In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this stu...In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this study,the consistency of printed electrodes was measured by using a confocal microscope and the pressure distribution detected by online pressure monitoring system was compared to investigate the relationship.The results demonstrated the relationship between printing pressure and the consistency of printed electrodes.As printing pressure increases,the ink layer at the corresponding position becomes thicker and that higher printing pressure enhances the consistency of the printed electrodes.The experiment confirms the feasibility of the online pressure monitoring system,which aids in predicting and controlling the consistency of printed electrodes,thereby improving their performance.展开更多
Free organic solvent ink containing graphite, carboxymethyl cellulose and microfibrillated cellulose as active material, dispersing and binder, respectively, has been formulated to produce flexible and eco- sustainabl...Free organic solvent ink containing graphite, carboxymethyl cellulose and microfibrillated cellulose as active material, dispersing and binder, respectively, has been formulated to produce flexible and eco- sustainable electrodes for lithium ion batteries. Content ratio of components and dispersion protocol were tailored in order to have theological properties suitable for a large and cheap manufacturing process as well as screen printing. The bio-sourced printed electrodes exhibit a high porosity value of 70% that limits the electrochemical performances. However, the calendering process enhances electrode performances by increasing the reversible capacity from 85 until 315 mAh/g and reducing porosity to an optimal value of 34%. Moreover the introduction of 2% w/w of monofluoro-ethylene carbonate in the electrolyte reduced their reversible capacity loss of 11% in the printed electrode.展开更多
Graphite screen printed electrode modified with Gd_2 O_3 nanoparticles(Gd_2 O_3/SPE) was developed for the determination of venlafaxine(VF). The Gd_2 O_3 nanoparticles were thoroughly characterized by scanning electro...Graphite screen printed electrode modified with Gd_2 O_3 nanoparticles(Gd_2 O_3/SPE) was developed for the determination of venlafaxine(VF). The Gd_2 O_3 nanoparticles were thoroughly characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM) and X-ray diffraction(XRD) analyses. To study the electrochemical behaviour of venlafaxine cyclic voltammetry(CV), chronoamperometry(CHA)and differential pulse voltammetry(DPV) were employed. These studies reveal that the oxidation of venlafaxine is facilitated at Gd_2 O_3/SPE. After optimization of analytical conditions, analysis of venlafaxine using the modified electrode in 0.1 mol/L PBS(pH 7.0) demonstrates that the peak currents corresponding to venlafaxine vary linearly with its concentration in the range of 5.0 ×10^(-6)-9.0 × 10^(-4) mol/L. The detection limit(S/N = 3) of 2.1 × 10^(-7) mol/L is obtained for venlafaxine using DPV. The prepared modified electrode benefits from advantages such as simple preparation method, high sensitivity and low detection limit.Moreover, the evaluation of practical applicability of this proposed method is successful in the identification of venlafaxine in pharmaceutical formulations, urine and water samples.展开更多
A sensitive and specific immunosensor for the detection of the hormones cortisol and lactate in human or animal biological fluids, such as sweat and saliva, was devised using the label-free electrochemical chronoamper...A sensitive and specific immunosensor for the detection of the hormones cortisol and lactate in human or animal biological fluids, such as sweat and saliva, was devised using the label-free electrochemical chronoamperometric technique. By using these fluids instead of blood,the biosensor becomes noninvasive and is less stressful to the end user, who may be a small child or a farm animal.Electroreduced graphene oxide(e-RGO) was used as a synergistic platform for signal amplification and template for bioconjugation for the sensing mechanism on a screenprinted electrode. The cortisol and lactate antibodies were bioconjugated to the e-RGO using covalent carbodiimide chemistry. Label-free electrochemical chronoamperometric detection was used to analyze the response to the desired biomolecules over the wide detection range. A detection limit of 0.1 ng mL^(-1) for cortisol and 0.1 mM for lactate was established and a correlation between concentration and current was observed. A portable, handheld potentiostat assembled with Bluetooth communication and battery operation enables the developed system for point-of-care applications. A sandwich-like structure containing the sensing mechanisms as a prototype was designed to secure the biosensor to skin and use capillary action to draw sweat or other fluids toward the sensing mechanism. Overall, the immunosensor shows remarkable specificity, sensitivity as well as the noninvasive and point-of-care capabilities and allows the biosensor to be used as a versatile sensing platform in both developed and developing countries.展开更多
A novel electrochemical method for the rapid detection of organophosphorus pesticide residues was realized on a dual-channel screen-printed electrode （DSPE） that was integrated with a portable smartphone-controlled ...A novel electrochemical method for the rapid detection of organophosphorus pesticide residues was realized on a dual-channel screen-printed electrode （DSPE） that was integrated with a portable smartphone-controlled potentiostat. The two carbon working channels of DSPE were first modified by electrodepositing of Prussian blue. The channels were then modified with acetylcholinesterase （ACHE） via Nation. The inhibition ratio of AChE was detected by comparing the electrical current of acetylthiocholine （ATCh） that was catalyzed by the enzyme electrodes with （channel 1） and without （channel 2） organophosphorus pesticide. Inhibition ratios were related with the negative logarithm of the organophosphorus pesticide （trichlorfon, oxamyl, and isocarbophos） concentrations at optimum experimental conditions （pH 6.9 of electrolyte, 0.2V working potential, 2.5μL AChE modification amount, and 15 min inhibition time）. The linear equations were 1%=32.301gC＋ 253.3 （R=0.9750） for isocarbophos, I% = 35.991gC＋ 270.1 （R = 0.9668） for chlorpyrifos, and 1% = 33.701gC＋ 250.5 （R = 0.9606） for trichlorfon. The detection limits were calculated as 10-7 g/mL. Given that the inhibition ratios were only related with pesticide concentration and not with pesticide species, the proposed electrodes and electrometer can rapidly detect universal organophosphorus pesticides and assess pesticide pollution.展开更多
The maximum level of organophosphate pesticide residues in rice is 0.1 mg/kg and 0.5 mg/kg in vegetables. The control of pesticide residues in agricultural products required a method of analysis quickly and accurately...The maximum level of organophosphate pesticide residues in rice is 0.1 mg/kg and 0.5 mg/kg in vegetables. The control of pesticide residues in agricultural products required a method of analysis quickly and accurately. The research developed a biosensor for the detection of organophosphate pesticide residues in agricultural products. The research studied immobilized organophosphate hydrolase (OPH) mass and characterization of biosensor. The solution conductivity measurement in the conductivity cell consists of a 1 × 5 mm2 pair of electrodes screen printed carbon electrode (SPCE). The instrument is a converted local conductometer. From the results of study concluded that the optimum performance of the biosensor was obtained from the 105 μg OPH, at pH 8.5 with a response time of 45 seconds. In that condition the sensitivity of biosensor is 28.04 μS/ppm and 0.18 ppm detection limit and the maximum concentration of pesticide which can be measured is 1 ppm. Biosensors have been applied to measure pesticide residues in some vegetable samples.展开更多
The electrochemical oxidation behavior and voltammetric assay of gemifloxacin were investigated using differential-pulse and cyclic voltammetry on a screen-printed carbon electrode.The effects of pH,scan rates,and con...The electrochemical oxidation behavior and voltammetric assay of gemifloxacin were investigated using differential-pulse and cyclic voltammetry on a screen-printed carbon electrode.The effects of pH,scan rates,and concentration of the drug on the anodic peak current were studied.Voltammograms of gemifloxacin in Tris-HCl buffer（pH 7.0） exhibited a well-defined single oxidation peak.A differential-pulse voltammetric procedure for the quantitation of gemifloxacin has been developed and suitably validated with respect to linearity,limits of detection and quantification,accuracy,precision,specificity,and robustness.The calibration was linear from 0.5 to 10.0 μM,and the limits of detection and quantification were 0.15 and 5.0 μM.Recoveries ranging from 96.26% to 103.64% were obtained.The method was successfully applied to the determination of gemifloxacin in pharmaceutical tablets without any pre-treatment.Excipients present in the tablets did not interfere in the assay.展开更多
The current work focuses on the development of a sensitive and selective electrochemical device based on a graphite screen printed electrode modified with Dy2（WO4）3 nanoparticles（DWO/SPE） for the analysis of epine...The current work focuses on the development of a sensitive and selective electrochemical device based on a graphite screen printed electrode modified with Dy2（WO4）3 nanoparticles（DWO/SPE） for the analysis of epinephrine in samples also containing acetylcholine. The study proves that the sensor has excellent electron-mediating behavior in the oxidation of epinephrine in a 0.1 mol/L phosphate buffer solution（PBS）（pH 7.0）. The application of the DWO/SPE in differential pulse voltammetry（DPV） is found to lead to distinct response for the oxidation of epinephrine and acetylcholine, with the potentials of the epinephrine and acetylcholine peaks（△Ep） to be 550 mV apart. The detection limits of the method for epinephrine and acetylcholine are 0.5 and 0.7 μmol/L（S/N = 3） and the responses are found to be linear in the concentration ranges of 1.0-900.0 μmol/L and 1.0-1200.0 μmol/L in a PBS buffer（pH = 7.0）respectively. The modified electrode was used for the detection of epinephrine and acetylcholine in real samples and found to produce satisfactory results. These results can be a proof that Dy2（WO4）3 nanoparticles can find promising applications in electrochemical sensors to be used for the analysis of（bio）chemical species.展开更多
We report the fabrication of disposable and flexible Screen-Printed Electrodes (SPEs). This new type of screen-printed electrochemical platform consists of Ag nanoparticles (AgNPs) and graphite composite. For this pur...We report the fabrication of disposable and flexible Screen-Printed Electrodes (SPEs). This new type of screen-printed electrochemical platform consists of Ag nanoparticles (AgNPs) and graphite composite. For this purpose, silver nanoparticles were first synthesized by a chemical reduction method. The morphology and structure of the AgNPs were analyzed using a Scanning Electron Microscope (SEM) and UV-Visible spectroscopy. Graphite was chosen as the working electrode material for the fabrication of a thick-film. The fabrication of a screen-printed hydrogen peroxide biosensor consisting of three electrodes on a polyethylene terephthalate (PET) substrate was performed with a spraying approach (working, counter and reference: enzyme electrode, graphite, pseudo reference: Ag/AgCl). This biosensor was fabricated by immobilizing the peroxidase enzyme (HRP) in a Titania sol-gel membrane which was obtained through a vapor deposition method. The biosensor had electrocatalytic activity in the reduction of H2O2 with linear dependence on H2O2 concentration in the range of 10-5 to 10-3 M;the detection limit was 4.5 × 10-6 M.展开更多
In this study, gold nanoparticles and thermochromic composite films modified screen-printed carbon electrodes (TM-AuNPsSPCEs) were developed as a platform for the simultaneous detection of protein and temperature. The...In this study, gold nanoparticles and thermochromic composite films modified screen-printed carbon electrodes (TM-AuNPsSPCEs) were developed as a platform for the simultaneous detection of protein and temperature. The TM-AuNPs composited film had better sensitivity resulting from the gold nanoparticles amplification effect. A phase transition model analysis of TM-AuNPs films found that the TM-AuNPs films had three-phase transition intervals (<45℃, 45℃ to 80℃ and >80℃) which accommodated the temperature requirements for protein denaturation. When used to detect different concentrations of haemoglobin (Hb) solution, the TM-AuNPs modified SPCEs had a better sensitivity in detecting the different concentrations in comparison to TM and AuNP modified SPCEs which showed no clear sensitivity towards the different Hb concentrations. The dual detection and excellent sensitivity show a good application prospect for the study of the TM-AuNPs composite film.展开更多
Metal-organic frameworks(MOFs)have attracted significant attention for energy storage applications due to their high surface area and tunable chemical properties.However,integrating MOFs into flexible,microstructured ...Metal-organic frameworks(MOFs)have attracted significant attention for energy storage applications due to their high surface area and tunable chemical properties.However,integrating MOFs into flexible,microstructured electrodes with good structural stability and printability remains challenging.In this study,electrohydrodynamic(EHD)jet printing was employed to fabricate microstructured supercapacitor electrodes based on a composite of ZIF-67(cobalt-based MOF)and polycaprolactone(PCL).ZIF-67 with high surface area and redox activity was embedded in a PCL matrix that helped regulate ink viscosity and offered structural support for the electrodes.The as-prepared hybrid electrodes exhibited uniform structure and tunable fiber spacing.Structural and compositional characterizations confirmed the successful integration of ZIF-67 and PCL,with homogeneous elemental distribution and well-defined Co-N coordination.Electrochemical evaluations demonstrated promising capacitive behavior,with a specific capacitance of∼230 mF/g and capacitance retention of 83%after 5000 cycles.These results highlight the potential of EHD printing for constructing MOF-based microelectrodes with controlled architectures,offering a new strategy for flexible and high-performance energy storage systems.展开更多
Flexible electrode films play critical and fundamental roles in the successful development of flexible electronic devices. In this study, carbon nanotubes（CNTs） were implanted into silver（Ag） ink to enhance the el...Flexible electrode films play critical and fundamental roles in the successful development of flexible electronic devices. In this study, carbon nanotubes（CNTs） were implanted into silver（Ag） ink to enhance the electrical conductivity and the reliability of the printed Ag electrode films. The fabricated carbon nanotubes-enriched silver（Ag-CNTs） electrode films were printed on the polyimide substrates by a facile screen printing method and sintered at a relatively low temperature. The resistivity of Ag-CNTs films was decreased by 62.27% compared with the pure Ag film. Additionally, the Ag-CNTs films exhibited excellent flexibility under a bending radius of 4 mm（strain ε = 2.09%） over 1000 cycles. Furthermore, the Ag-CNTs film displayed unchangeable electrical conductivity together with a strong adhesion after an accelerated aging test with 500 thermal shock cycles. These improvements were attributed to the AgCNTs interconnected network structure, which can provide electronic transmission channels and prevent cracks from initiating and propagating.展开更多
Electrochemical energy storage(EES)systems like batteries and supercapacitors are becoming the key power sources for attempts to change the energy dependency from inadequate fossil fuels to sustainable and renewable r...Electrochemical energy storage(EES)systems like batteries and supercapacitors are becoming the key power sources for attempts to change the energy dependency from inadequate fossil fuels to sustainable and renewable resources.Electrochemical energy storage devices(EESDs)operate efficiently as a result of the construction and assemblage of electrodes and electrolytes with appropriate structures and effective materials.Conventional manufacturing procedures have restrictions on regulating the morphology and architecture of the electrodes,which would influence the performance of the devices.3D printing(3DP)is an advanced manufacturing technology combining computer-aided design and has been recognised as an artistic method of fabricating different fragments of energy storage devices with its ability to precisely control the geometry,porosity,and morphology with improved specific energy and power densities.The capacity to create mathematically challenging shape or configuration designs and high-aspect-ratio 3D architectures makes 3D printing technology unique in its benefits.Nevertheless,the control settings,interactive manufacturing processes,and protracted post-treatments will affect the reproducibility of the printed components.More intelligent software,sophisticated control systems,high-grade industrial equipment,and post-treatment-free methods are necessary to develop.3D printed(3DPd)EESDs necessitate dynamic printable materials and composites that are influenced by performance criteria and fundamental electrochemistry.Herein,we review the recent advances in 3DPd electrodes for EES applications.The emphasis is on printable material synthesis,3DP techniques,and the electrochemical performance of printed electrodes.For the fabrication of electrodes,we concentrate on major 3DP technologies such as direct ink writing(DIW),inkjet printing(IJP),fused deposition modelling(FDM),and stereolithography3DP(SLA).The benefits and drawbacks of each 3DP technology are extensively discussed.We provide an outlook on the integration of synthesis of emerging nanomaterials and fabrication of complex structures from micro to macroscale to construct highly effective electrodes for the EESDs.展开更多
In this work, a simple procedure for the preparation of an inkjet printed disposable graphene electrode is reported. Commercial graphene ink was printed on a kapton substrate and the resulting electrode was 30 min tre...In this work, a simple procedure for the preparation of an inkjet printed disposable graphene electrode is reported. Commercial graphene ink was printed on a kapton substrate and the resulting electrode was 30 min treated by oxygen plasma, then modified by a bismuth salt. The as prepared electrode was characterized by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), laser scanning microscopy (LSM) and scanning electron microscopy (SEM) coupled to energy-dispersive X-ray spectroscopy (EDX). The sensing properties of the characterized electrodes were then investigated using cyclic voltammetry and Electrochemical Impedance Spectroscopy (EIS). Afterwards, these electrodes were exploited in a comparative way for the electroanalysis of Cadmium(II) and Lead(II) ions. An increase in the electrode sensitivity due to its modification and to the presence of bismuth was observed. Some preliminary experiments based on stripping square wave voltammetry highlighted the interest of using the proposed disposable inkjet printed electrodes for the electrochemical detection of heavy metals in tap water.展开更多
Screen printing is regarded as a highly competitive manufacture technology for scalable and fast fabrication of printed microelectronics, owing to its advanced merits of low-cost, facile operability and scalability.Ho...Screen printing is regarded as a highly competitive manufacture technology for scalable and fast fabrication of printed microelectronics, owing to its advanced merits of low-cost, facile operability and scalability.However, its large-scale application in printed microelectronics is still limited by screen printing functional ink. In this review, we summarize the recent advances of ink formation, typical scalable applications, and challenging perspectives of screen printing for emerging printed microelectronics. Firstly, we introduce the major mechanism of screen printing and the formation of different organic-and aqueous-based inks by various solvents and binders. Next, we review the most widely used applications of screen printing technique in micro-batteries, micro-supercapacitors and micro-sensors, demonstrative of wide applicability.Finally, the perspectives and future challenges in the sight of screen printing are briefly discussed.展开更多
Conductive inks based on graphene materials have received significant attention for the fabrication of a wide range of printed and flexible devices.However,the application of graphene fillers is limited by their restr...Conductive inks based on graphene materials have received significant attention for the fabrication of a wide range of printed and flexible devices.However,the application of graphene fillers is limited by their restricted mass production and the low concentration of their suspensions.In this study,a highly concentrated and conductive ink based on defect-free graphene was developed by a scalable fluid dynamics process.A high shear exfoliation and mixing process enabled the production of graphene at a high concentration of 47.5 mg mL^(−1)for graphene ink.The screen-printed graphene conductor exhibits a high electrical conductivity of 1.49×10^(4)S m^(−1)and maintains high conductivity under mechanical bending,compressing,and fatigue tests.Based on the as-prepared graphene ink,a printed electrochemical sodium ion(Na^(+))sensor that shows high potentiometric sensing performance was fabricated.Further,by integrating a wireless electronic module,a prototype Na^(+)-sensing watch is demonstrated for the real-time monitoring of the sodium ion concentration in human sweat during the indoor exercise of a volunteer.The scalable and efficient procedure for the preparation of graphene ink presented in this work is very promising for the low-cost,reproducible,and large-scale printing of flexible and wearable electronic devices.展开更多
Fractal-structured silver particles(FSSPs)are conductive materials with a micron-scale trunk and nanoscale branches,and are characterized with high electrical conductivity and high connectivity.In this study,FSSPs wer...Fractal-structured silver particles(FSSPs)are conductive materials with a micron-scale trunk and nanoscale branches,and are characterized with high electrical conductivity and high connectivity.In this study,FSSPs were added to an aqueous additive solution for synthesizing a conductive ink,which was used to prepare two types of printing electrodes via screen printing.The first type included two flexible printed electrodes(FPEs):an FPE on a polyethylene terephthalate(PET)film and an FPE on paper.The second one was a polydimethylsiloxane(PDMS)-embedded FPE.The PETbased FPE exhibited high electrochemical stability when its sheet resistance was 0.38Ω/sq for a 50%(w/w)content of FSSPs in the prepared conductive ink.Moreover,the embedded FPE demonstrated excellent mechanical properties and high chemical stability.In addition,the embedded structure was endowed with stretchability,which is important for different devices,such as flexible biomedical sensors and flexible electronics.展开更多
Compared with bar code and quick response( QR) code in the storage and retailing management of textiles, the ultra-high frequency( UHF) radio frequency identification( RFID) tags have high information capacity as well...Compared with bar code and quick response( QR) code in the storage and retailing management of textiles, the ultra-high frequency( UHF) radio frequency identification( RFID) tags have high information capacity as well as reliability in complex environmental conditions. In this study,the UHF RFID tags with perfect integration with textiles are assembled with screen-printed antenna on woven water-mark nylon fabric and Alien UHF integrated circuit( IC), and their reading performance under various washing and bending conditions is evaluated by an RFID reader. The results show that the tags after fifty bending( both arch and sink) cycles of screen-printed antenna still have reading distance more than 5.5 m,and an average reading distance is over 4.0 m after five washing cycles. The experimental results demonstrate that the tag antenna on the water-mark fabric can be manufactured by the screen-printing technology,and a coating process on this fabric facilitates the reading performance and the resistance against complex mechanical impact.展开更多
Perovskite solar cells(PSCs)have reached a recorded power conversion efficiency(PCE)of 25.7%just over a decade.1 Due to the solution processability,various deposition methods have been developed to prepare PSCs,includ...Perovskite solar cells(PSCs)have reached a recorded power conversion efficiency(PCE)of 25.7%just over a decade.1 Due to the solution processability,various deposition methods have been developed to prepare PSCs,including spin coating,blade coating,spray coating,slot-die printing,and ink-jet printing.2,3 Among them,screen printing has received great attention due to the unique advantages of customized pattern design,high throughput,and low-cost production.Thus this technology holds a great promise for industrialization of perovskite solar cells.4 Till now,screen printing has been successfully applied to prepare buffer layers and electrodes of PSCs,but attempts in perovskite-layer fabrication have failed.The key problem is that the commonly used organic solvents with a low viscosity are not fit for screen printing,which limits the application of this deposition technology for perovskite-film manufacturing.展开更多
文摘In order to address the current inability of screen printing to monitor printing pressure online,an online printing pressure monitoring system applied to screen printing machines was designed in this study.In this study,the consistency of printed electrodes was measured by using a confocal microscope and the pressure distribution detected by online pressure monitoring system was compared to investigate the relationship.The results demonstrated the relationship between printing pressure and the consistency of printed electrodes.As printing pressure increases,the ink layer at the corresponding position becomes thicker and that higher printing pressure enhances the consistency of the printed electrodes.The experiment confirms the feasibility of the online pressure monitoring system,which aids in predicting and controlling the consistency of printed electrodes,thereby improving their performance.
基金partially supported by theénergies du Futur Carnot Institute(Investissements d’Avenir-grant agreement No.ANR-11-CARN-030-01)the facilities of the Tek Li Cell platform funded by the Région Rhone-Alpes(ERDF:European Regional Development Fund)
文摘Free organic solvent ink containing graphite, carboxymethyl cellulose and microfibrillated cellulose as active material, dispersing and binder, respectively, has been formulated to produce flexible and eco- sustainable electrodes for lithium ion batteries. Content ratio of components and dispersion protocol were tailored in order to have theological properties suitable for a large and cheap manufacturing process as well as screen printing. The bio-sourced printed electrodes exhibit a high porosity value of 70% that limits the electrochemical performances. However, the calendering process enhances electrode performances by increasing the reversible capacity from 85 until 315 mAh/g and reducing porosity to an optimal value of 34%. Moreover the introduction of 2% w/w of monofluoro-ethylene carbonate in the electrolyte reduced their reversible capacity loss of 11% in the printed electrode.
文摘Graphite screen printed electrode modified with Gd_2 O_3 nanoparticles(Gd_2 O_3/SPE) was developed for the determination of venlafaxine(VF). The Gd_2 O_3 nanoparticles were thoroughly characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM) and X-ray diffraction(XRD) analyses. To study the electrochemical behaviour of venlafaxine cyclic voltammetry(CV), chronoamperometry(CHA)and differential pulse voltammetry(DPV) were employed. These studies reveal that the oxidation of venlafaxine is facilitated at Gd_2 O_3/SPE. After optimization of analytical conditions, analysis of venlafaxine using the modified electrode in 0.1 mol/L PBS(pH 7.0) demonstrates that the peak currents corresponding to venlafaxine vary linearly with its concentration in the range of 5.0 ×10^(-6)-9.0 × 10^(-4) mol/L. The detection limit(S/N = 3) of 2.1 × 10^(-7) mol/L is obtained for venlafaxine using DPV. The prepared modified electrode benefits from advantages such as simple preparation method, high sensitivity and low detection limit.Moreover, the evaluation of practical applicability of this proposed method is successful in the identification of venlafaxine in pharmaceutical formulations, urine and water samples.
基金the Natural Sciences and Engineering Research Council of Canada (400705) for funding this study
文摘A sensitive and specific immunosensor for the detection of the hormones cortisol and lactate in human or animal biological fluids, such as sweat and saliva, was devised using the label-free electrochemical chronoamperometric technique. By using these fluids instead of blood,the biosensor becomes noninvasive and is less stressful to the end user, who may be a small child or a farm animal.Electroreduced graphene oxide(e-RGO) was used as a synergistic platform for signal amplification and template for bioconjugation for the sensing mechanism on a screenprinted electrode. The cortisol and lactate antibodies were bioconjugated to the e-RGO using covalent carbodiimide chemistry. Label-free electrochemical chronoamperometric detection was used to analyze the response to the desired biomolecules over the wide detection range. A detection limit of 0.1 ng mL^(-1) for cortisol and 0.1 mM for lactate was established and a correlation between concentration and current was observed. A portable, handheld potentiostat assembled with Bluetooth communication and battery operation enables the developed system for point-of-care applications. A sandwich-like structure containing the sensing mechanisms as a prototype was designed to secure the biosensor to skin and use capillary action to draw sweat or other fluids toward the sensing mechanism. Overall, the immunosensor shows remarkable specificity, sensitivity as well as the noninvasive and point-of-care capabilities and allows the biosensor to be used as a versatile sensing platform in both developed and developing countries.
基金financially supported by the Natural Science Foundation of Zhejiang Province(No.LQ17B050002)Analysis and Measurement Foundation of Zhejiang Province(No.2015C37068)
文摘A novel electrochemical method for the rapid detection of organophosphorus pesticide residues was realized on a dual-channel screen-printed electrode （DSPE） that was integrated with a portable smartphone-controlled potentiostat. The two carbon working channels of DSPE were first modified by electrodepositing of Prussian blue. The channels were then modified with acetylcholinesterase （ACHE） via Nation. The inhibition ratio of AChE was detected by comparing the electrical current of acetylthiocholine （ATCh） that was catalyzed by the enzyme electrodes with （channel 1） and without （channel 2） organophosphorus pesticide. Inhibition ratios were related with the negative logarithm of the organophosphorus pesticide （trichlorfon, oxamyl, and isocarbophos） concentrations at optimum experimental conditions （pH 6.9 of electrolyte, 0.2V working potential, 2.5μL AChE modification amount, and 15 min inhibition time）. The linear equations were 1%=32.301gC＋ 253.3 （R=0.9750） for isocarbophos, I% = 35.991gC＋ 270.1 （R = 0.9668） for chlorpyrifos, and 1% = 33.701gC＋ 250.5 （R = 0.9606） for trichlorfon. The detection limits were calculated as 10-7 g/mL. Given that the inhibition ratios were only related with pesticide concentration and not with pesticide species, the proposed electrodes and electrometer can rapidly detect universal organophosphorus pesticides and assess pesticide pollution.
文摘The maximum level of organophosphate pesticide residues in rice is 0.1 mg/kg and 0.5 mg/kg in vegetables. The control of pesticide residues in agricultural products required a method of analysis quickly and accurately. The research developed a biosensor for the detection of organophosphate pesticide residues in agricultural products. The research studied immobilized organophosphate hydrolase (OPH) mass and characterization of biosensor. The solution conductivity measurement in the conductivity cell consists of a 1 × 5 mm2 pair of electrodes screen printed carbon electrode (SPCE). The instrument is a converted local conductometer. From the results of study concluded that the optimum performance of the biosensor was obtained from the 105 μg OPH, at pH 8.5 with a response time of 45 seconds. In that condition the sensitivity of biosensor is 28.04 μS/ppm and 0.18 ppm detection limit and the maximum concentration of pesticide which can be measured is 1 ppm. Biosensors have been applied to measure pesticide residues in some vegetable samples.
文摘The electrochemical oxidation behavior and voltammetric assay of gemifloxacin were investigated using differential-pulse and cyclic voltammetry on a screen-printed carbon electrode.The effects of pH,scan rates,and concentration of the drug on the anodic peak current were studied.Voltammograms of gemifloxacin in Tris-HCl buffer（pH 7.0） exhibited a well-defined single oxidation peak.A differential-pulse voltammetric procedure for the quantitation of gemifloxacin has been developed and suitably validated with respect to linearity,limits of detection and quantification,accuracy,precision,specificity,and robustness.The calibration was linear from 0.5 to 10.0 μM,and the limits of detection and quantification were 0.15 and 5.0 μM.Recoveries ranging from 96.26% to 103.64% were obtained.The method was successfully applied to the determination of gemifloxacin in pharmaceutical tablets without any pre-treatment.Excipients present in the tablets did not interfere in the assay.
文摘The current work focuses on the development of a sensitive and selective electrochemical device based on a graphite screen printed electrode modified with Dy2（WO4）3 nanoparticles（DWO/SPE） for the analysis of epinephrine in samples also containing acetylcholine. The study proves that the sensor has excellent electron-mediating behavior in the oxidation of epinephrine in a 0.1 mol/L phosphate buffer solution（PBS）（pH 7.0）. The application of the DWO/SPE in differential pulse voltammetry（DPV） is found to lead to distinct response for the oxidation of epinephrine and acetylcholine, with the potentials of the epinephrine and acetylcholine peaks（△Ep） to be 550 mV apart. The detection limits of the method for epinephrine and acetylcholine are 0.5 and 0.7 μmol/L（S/N = 3） and the responses are found to be linear in the concentration ranges of 1.0-900.0 μmol/L and 1.0-1200.0 μmol/L in a PBS buffer（pH = 7.0）respectively. The modified electrode was used for the detection of epinephrine and acetylcholine in real samples and found to produce satisfactory results. These results can be a proof that Dy2（WO4）3 nanoparticles can find promising applications in electrochemical sensors to be used for the analysis of（bio）chemical species.
文摘We report the fabrication of disposable and flexible Screen-Printed Electrodes (SPEs). This new type of screen-printed electrochemical platform consists of Ag nanoparticles (AgNPs) and graphite composite. For this purpose, silver nanoparticles were first synthesized by a chemical reduction method. The morphology and structure of the AgNPs were analyzed using a Scanning Electron Microscope (SEM) and UV-Visible spectroscopy. Graphite was chosen as the working electrode material for the fabrication of a thick-film. The fabrication of a screen-printed hydrogen peroxide biosensor consisting of three electrodes on a polyethylene terephthalate (PET) substrate was performed with a spraying approach (working, counter and reference: enzyme electrode, graphite, pseudo reference: Ag/AgCl). This biosensor was fabricated by immobilizing the peroxidase enzyme (HRP) in a Titania sol-gel membrane which was obtained through a vapor deposition method. The biosensor had electrocatalytic activity in the reduction of H2O2 with linear dependence on H2O2 concentration in the range of 10-5 to 10-3 M;the detection limit was 4.5 × 10-6 M.
文摘In this study, gold nanoparticles and thermochromic composite films modified screen-printed carbon electrodes (TM-AuNPsSPCEs) were developed as a platform for the simultaneous detection of protein and temperature. The TM-AuNPs composited film had better sensitivity resulting from the gold nanoparticles amplification effect. A phase transition model analysis of TM-AuNPs films found that the TM-AuNPs films had three-phase transition intervals (<45℃, 45℃ to 80℃ and >80℃) which accommodated the temperature requirements for protein denaturation. When used to detect different concentrations of haemoglobin (Hb) solution, the TM-AuNPs modified SPCEs had a better sensitivity in detecting the different concentrations in comparison to TM and AuNP modified SPCEs which showed no clear sensitivity towards the different Hb concentrations. The dual detection and excellent sensitivity show a good application prospect for the study of the TM-AuNPs composite film.
基金supported by National Natural Science Foundation of China(Grant No.52305426)Postdoctoral Research Foundation of China(Grant No.2022M722690)+1 种基金State Key Laboratory for Manufacturing Systems Engineering(Grant No.sklms2022014)Yangzhou Innovation Capability Enhancement Program(Grant No.YZ2022170).
文摘Metal-organic frameworks(MOFs)have attracted significant attention for energy storage applications due to their high surface area and tunable chemical properties.However,integrating MOFs into flexible,microstructured electrodes with good structural stability and printability remains challenging.In this study,electrohydrodynamic(EHD)jet printing was employed to fabricate microstructured supercapacitor electrodes based on a composite of ZIF-67(cobalt-based MOF)and polycaprolactone(PCL).ZIF-67 with high surface area and redox activity was embedded in a PCL matrix that helped regulate ink viscosity and offered structural support for the electrodes.The as-prepared hybrid electrodes exhibited uniform structure and tunable fiber spacing.Structural and compositional characterizations confirmed the successful integration of ZIF-67 and PCL,with homogeneous elemental distribution and well-defined Co-N coordination.Electrochemical evaluations demonstrated promising capacitive behavior,with a specific capacitance of∼230 mF/g and capacitance retention of 83%after 5000 cycles.These results highlight the potential of EHD printing for constructing MOF-based microelectrodes with controlled architectures,offering a new strategy for flexible and high-performance energy storage systems.
基金supported financially by the Joint Funds of the National Natural Science Foundation of China (Grant No. U1601213)the National Natural Science Foundation of China (Grant No. 51601005)the Fundamental Research Funds for the Central Universities.
文摘Flexible electrode films play critical and fundamental roles in the successful development of flexible electronic devices. In this study, carbon nanotubes（CNTs） were implanted into silver（Ag） ink to enhance the electrical conductivity and the reliability of the printed Ag electrode films. The fabricated carbon nanotubes-enriched silver（Ag-CNTs） electrode films were printed on the polyimide substrates by a facile screen printing method and sintered at a relatively low temperature. The resistivity of Ag-CNTs films was decreased by 62.27% compared with the pure Ag film. Additionally, the Ag-CNTs films exhibited excellent flexibility under a bending radius of 4 mm（strain ε = 2.09%） over 1000 cycles. Furthermore, the Ag-CNTs film displayed unchangeable electrical conductivity together with a strong adhesion after an accelerated aging test with 500 thermal shock cycles. These improvements were attributed to the AgCNTs interconnected network structure, which can provide electronic transmission channels and prevent cracks from initiating and propagating.
基金supported by the National Research Foundation of Korea (NRF)grant funded by the Korea government (MSIT) (No.2021R1A2C2006888)。
文摘Electrochemical energy storage(EES)systems like batteries and supercapacitors are becoming the key power sources for attempts to change the energy dependency from inadequate fossil fuels to sustainable and renewable resources.Electrochemical energy storage devices(EESDs)operate efficiently as a result of the construction and assemblage of electrodes and electrolytes with appropriate structures and effective materials.Conventional manufacturing procedures have restrictions on regulating the morphology and architecture of the electrodes,which would influence the performance of the devices.3D printing(3DP)is an advanced manufacturing technology combining computer-aided design and has been recognised as an artistic method of fabricating different fragments of energy storage devices with its ability to precisely control the geometry,porosity,and morphology with improved specific energy and power densities.The capacity to create mathematically challenging shape or configuration designs and high-aspect-ratio 3D architectures makes 3D printing technology unique in its benefits.Nevertheless,the control settings,interactive manufacturing processes,and protracted post-treatments will affect the reproducibility of the printed components.More intelligent software,sophisticated control systems,high-grade industrial equipment,and post-treatment-free methods are necessary to develop.3D printed(3DPd)EESDs necessitate dynamic printable materials and composites that are influenced by performance criteria and fundamental electrochemistry.Herein,we review the recent advances in 3DPd electrodes for EES applications.The emphasis is on printable material synthesis,3DP techniques,and the electrochemical performance of printed electrodes.For the fabrication of electrodes,we concentrate on major 3DP technologies such as direct ink writing(DIW),inkjet printing(IJP),fused deposition modelling(FDM),and stereolithography3DP(SLA).The benefits and drawbacks of each 3DP technology are extensively discussed.We provide an outlook on the integration of synthesis of emerging nanomaterials and fabrication of complex structures from micro to macroscale to construct highly effective electrodes for the EESDs.
文摘In this work, a simple procedure for the preparation of an inkjet printed disposable graphene electrode is reported. Commercial graphene ink was printed on a kapton substrate and the resulting electrode was 30 min treated by oxygen plasma, then modified by a bismuth salt. The as prepared electrode was characterized by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), laser scanning microscopy (LSM) and scanning electron microscopy (SEM) coupled to energy-dispersive X-ray spectroscopy (EDX). The sensing properties of the characterized electrodes were then investigated using cyclic voltammetry and Electrochemical Impedance Spectroscopy (EIS). Afterwards, these electrodes were exploited in a comparative way for the electroanalysis of Cadmium(II) and Lead(II) ions. An increase in the electrode sensitivity due to its modification and to the presence of bismuth was observed. Some preliminary experiments based on stripping square wave voltammetry highlighted the interest of using the proposed disposable inkjet printed electrodes for the electrochemical detection of heavy metals in tap water.
基金This workwas mpported bygrants from the KeyBasic Research and Development Program （＂973＂ Program） of China （2007CB513108）, Deutsche Fo~hungsgemeLn_s chaft （DFG, Germany） （KO4136/1-1 ）, the ＂Eleventh Five-Year＂ National Key Technology R＆D Program of China （2009BAI78BO5）, the Key Laboratory of Immune and Contxol Schistosomiasis, and the Key Subject Development Special Program of Hunan Province, P.R. China （2008-985-2）.
基金financially supported by the National Key R@D Program of China (2016YFB0100100,2016YFA0200200)the National Natural Science Foundation of China (22125903,51872283,22075279,21805273,22005297,22005298)+7 种基金the Liao Ning Revitalization Talents Program (XLYC1807153)the CentralGovernment of Liaoning Province Guides The Funds for Local Science and Technology Development (2021JH6/10500112)the Dalian Innovation Support Plan for High Level Talents(2019RT09)the Dalian National Laboratory For Clean Energy(DNL)the CASDNL Cooperation Fund,CAS (DNL201912,DNL201915,DNL202016,DNL202019)DICP (DICP ZZBS201708,DICP ZZBS201802,DICP I2020032)the China Postdoctoral Science Foundation (2019M661141,2020M680995)。
文摘Screen printing is regarded as a highly competitive manufacture technology for scalable and fast fabrication of printed microelectronics, owing to its advanced merits of low-cost, facile operability and scalability.However, its large-scale application in printed microelectronics is still limited by screen printing functional ink. In this review, we summarize the recent advances of ink formation, typical scalable applications, and challenging perspectives of screen printing for emerging printed microelectronics. Firstly, we introduce the major mechanism of screen printing and the formation of different organic-and aqueous-based inks by various solvents and binders. Next, we review the most widely used applications of screen printing technique in micro-batteries, micro-supercapacitors and micro-sensors, demonstrative of wide applicability.Finally, the perspectives and future challenges in the sight of screen printing are briefly discussed.
基金the National Research Foundation of Korea(NRF)Grant funded by the Ministry of Science and ICT(No.2021R1A2C1009926)“Basic project(referring to projects performed with the budget directly contributed by the Government to achieve the purposes of establishment of Government-funded research Institutes)”+3 种基金supported by the KOREA RESEARCH INSTITUTE of CHEMICAL TECHNOLOGY(KRICT)(SS2042-10)Basic research project(Project:21-3212-1)of the Korea institute of GeoscienceMineral resources funded by the Ministry of Science and ICT of Koreaby Nanomedical Devices Development Project of NNFC in 2021.
文摘Conductive inks based on graphene materials have received significant attention for the fabrication of a wide range of printed and flexible devices.However,the application of graphene fillers is limited by their restricted mass production and the low concentration of their suspensions.In this study,a highly concentrated and conductive ink based on defect-free graphene was developed by a scalable fluid dynamics process.A high shear exfoliation and mixing process enabled the production of graphene at a high concentration of 47.5 mg mL^(−1)for graphene ink.The screen-printed graphene conductor exhibits a high electrical conductivity of 1.49×10^(4)S m^(−1)and maintains high conductivity under mechanical bending,compressing,and fatigue tests.Based on the as-prepared graphene ink,a printed electrochemical sodium ion(Na^(+))sensor that shows high potentiometric sensing performance was fabricated.Further,by integrating a wireless electronic module,a prototype Na^(+)-sensing watch is demonstrated for the real-time monitoring of the sodium ion concentration in human sweat during the indoor exercise of a volunteer.The scalable and efficient procedure for the preparation of graphene ink presented in this work is very promising for the low-cost,reproducible,and large-scale printing of flexible and wearable electronic devices.
基金supported by the International Joint Research Center for Biomass Chemistry and Materials,Shaanxi International Science and Technology Cooperation Base(2018GHJD-19)the Shaanxi Key Industry Innovation Chain Projects(2020ZDLGY11-03)+2 种基金the Science and Technology Plan of Weiyang District of Xi'an(201910)the Scientific Research Plan Projects of Shaanxi Education Department(19JK0131)The project was also supported by the Foundation of Key Laboratory of Pulp and Paper Science and Technology of the Ministry of Education/Shandong Province of China(KF201814).
文摘Fractal-structured silver particles(FSSPs)are conductive materials with a micron-scale trunk and nanoscale branches,and are characterized with high electrical conductivity and high connectivity.In this study,FSSPs were added to an aqueous additive solution for synthesizing a conductive ink,which was used to prepare two types of printing electrodes via screen printing.The first type included two flexible printed electrodes(FPEs):an FPE on a polyethylene terephthalate(PET)film and an FPE on paper.The second one was a polydimethylsiloxane(PDMS)-embedded FPE.The PETbased FPE exhibited high electrochemical stability when its sheet resistance was 0.38Ω/sq for a 50%(w/w)content of FSSPs in the prepared conductive ink.Moreover,the embedded FPE demonstrated excellent mechanical properties and high chemical stability.In addition,the embedded structure was endowed with stretchability,which is important for different devices,such as flexible biomedical sensors and flexible electronics.
基金National Natural Science Foundation of China(Nos.51405079)China Postdoctoral Science Foundation of China(No.2015M570307)+1 种基金the Fundamental Research Funds for the Central Universities,Chinathe Jiangsu Planned Projects for Postdoctoral Research Funds,China
文摘Compared with bar code and quick response( QR) code in the storage and retailing management of textiles, the ultra-high frequency( UHF) radio frequency identification( RFID) tags have high information capacity as well as reliability in complex environmental conditions. In this study,the UHF RFID tags with perfect integration with textiles are assembled with screen-printed antenna on woven water-mark nylon fabric and Alien UHF integrated circuit( IC), and their reading performance under various washing and bending conditions is evaluated by an RFID reader. The results show that the tags after fifty bending( both arch and sink) cycles of screen-printed antenna still have reading distance more than 5.5 m,and an average reading distance is over 4.0 m after five washing cycles. The experimental results demonstrate that the tag antenna on the water-mark fabric can be manufactured by the screen-printing technology,and a coating process on this fabric facilitates the reading performance and the resistance against complex mechanical impact.
文摘Perovskite solar cells(PSCs)have reached a recorded power conversion efficiency(PCE)of 25.7%just over a decade.1 Due to the solution processability,various deposition methods have been developed to prepare PSCs,including spin coating,blade coating,spray coating,slot-die printing,and ink-jet printing.2,3 Among them,screen printing has received great attention due to the unique advantages of customized pattern design,high throughput,and low-cost production.Thus this technology holds a great promise for industrialization of perovskite solar cells.4 Till now,screen printing has been successfully applied to prepare buffer layers and electrodes of PSCs,but attempts in perovskite-layer fabrication have failed.The key problem is that the commonly used organic solvents with a low viscosity are not fit for screen printing,which limits the application of this deposition technology for perovskite-film manufacturing.
