A significant enhancement in solar hydrogen generation efficiency has been achieved by inductive coupled etching （ICP） surface roughening treatment using nano-sized nickel mask. As much as 7 times improvement of pho...A significant enhancement in solar hydrogen generation efficiency has been achieved by inductive coupled etching （ICP） surface roughening treatment using nano-sized nickel mask. As much as 7 times improvement of photocurrent is demonstrated in comparison with a planar one fabricated from the same parent wafer. Under identical illumination conditions in HBr solution, the incident photon conversion efficiency （IPCE） shows an enhancement with a factor of 3, which even exceed 54% at 400 nm wavelength. We believe the enhancement is attributed to several facts including improvement in absorption, reacting area, carder localization and carrier lifetime.展开更多
Impingement heat transfer from the rib roughened surface within 2 dimensional arrays of circular jet has been experimentally investigated.This investigation is intended here to include the flow and the heat transfer c...Impingement heat transfer from the rib roughened surface within 2 dimensional arrays of circular jet has been experimentally investigated.This investigation is intended here to include the flow and the heat transfer characteristics of the jet impinging on the rib roughened surface with initial crossflow for simulating the impingement cooling midchord region of the gas turbine aerofoils in case where an initial crossflow is presented.The study covered the ranges of crossflow G_(c)/G_(j)=0~0.55 under the conditions of Re_(j)=8000~11000 and Z/d=1.5~3.0 for smooth and rib roughened surfaces.The test results show that the impingement heat transfer from the rib roughened surface is considerably affected by the initial crossflow rate.The existence of the initial crossflow will improve the efficiency of the impingement heat transfer from the rib roughened surface within arrays of circular jet compared with that from the smooth surface.展开更多
Low resistance and thermally stable n-type contacts to N-polar GaN are essentially important for vertical light emitting diodes （VLEDs）. The electrical characteristics of VLEDs with n-type contacts on a roughened an...Low resistance and thermally stable n-type contacts to N-polar GaN are essentially important for vertical light emitting diodes （VLEDs）. The electrical characteristics of VLEDs with n-type contacts on a roughened and flat N-polar surface have been compared. VLEDs with contacts deposited on a roughened surface exhibit lower leakage currents yet a higher operating voltage. Based on this, a new scheme by depositing metallization contacts on a selectively wet-etching roughened surface has been developed. Excellent electrical and optical characteristics have been achieved with this method. An aging test further confirmed its stability.展开更多
By using the wafer bonding technique and wet etching process,a wafer bonded thin film AlGaInP LED with wet etched n-AlGaInP surfaces was fabricated.The morphology of the etched surface exhibits a pyramid-like feature....By using the wafer bonding technique and wet etching process,a wafer bonded thin film AlGaInP LED with wet etched n-AlGaInP surfaces was fabricated.The morphology of the etched surface exhibits a pyramid-like feature.The wafer was cut into 270×270μm2 chips and then packaged into TO-18 without epoxy resin.With 20-mA current injection,the light intensity and output power of LED-Ⅰwith surface roughening respectively reach 315 mcd and 4.622 mW,which was 1.7 times higher than that of LED-Ⅱwithout surface roughening.The enhancement of output power in LED-Ⅰcan be attributed to the pyramid-like surface,which not only reduces the total internal reflection at the semiconductor-air interface but also effectively guides more photons into the escape angle for emission from the LED device.展开更多
The morphology and lateral growth rate of isotactic polybutene-1(it-PB1)have been investigated for crystallization from the melt over a wide range of crystallization temperatures from 50 to 110℃.The morphology of it-...The morphology and lateral growth rate of isotactic polybutene-1(it-PB1)have been investigated for crystallization from the melt over a wide range of crystallization temperatures from 50 to 110℃.The morphology of it-PB1 crystals is a rounded shape at crystallization temperatures lower than 85℃,while lamellarsingle crystals possess faceted morphology at higher crystallization temperatures.The kinetic roughening transi-tion occurs around 85℃.The nucleation and growth mechanism for crystallization does not work below 85℃,since the growth face is rough.However,the growth rate shows the supercooling dependence derived from the nucleation and growth mechanism.The nucleation theory seems still to work even for rough surface growth.Possible mechanisms for the crystal growth of this polymer are discussed.展开更多
The light beating technique (intensity correlation algorithm) was employed to analyze the Rayleigh scattering from the roughened Ag electrode in very dilute (10^(-4)M) pyrazine, pyridine and piperidine aqueous solutio...The light beating technique (intensity correlation algorithm) was employed to analyze the Rayleigh scattering from the roughened Ag electrode in very dilute (10^(-4)M) pyrazine, pyridine and piperidine aqueous solutions containing KCl (0.1 M). The relaxation time is longer when the applied voltages are between-0.4 V and-0.8 V(vs. SCE) where the Raman effect also shows greater surface enhancement. Also observed was that for the piperidine case the relaxation time reaches its maximum at the more negative applied voltage. The origin of the relaxation is attributed mainly to the desorp- tion process of the pyrazine. pyridine and piperidine molecules off the roughened Ag electrode. An. electrostatic model was also proposed for the interpretation of these experimental observations.展开更多
An ultraviolet (UV) laser lift-off (LLO) technique was presented to form a roughened surface morphol-ogy on GaN membrane grown by metalorganic chemical vapor deposition (MOCVD). The etched sur-face showed cone-like st...An ultraviolet (UV) laser lift-off (LLO) technique was presented to form a roughened surface morphol-ogy on GaN membrane grown by metalorganic chemical vapor deposition (MOCVD). The etched sur-face showed cone-like structures on a free-standing GaN membrane. Based on the scanning electron microscopy (SEM) and atom force microscopy (AFM) measurements, the etching mechanism was proposed, which was related to the different decomposition depth caused by the dislocations in the GaN membrane. The etching efficiency and morphology of GaN by the LLO technique and the photo-electrochemical (PEC) wet etching technique was compared and analyzed. This roughed cone-like surface morphology by LLO can enhance the external efficiency of vertical structure n-side-up GaN-based light-emitting diodes (LEDs) simultaneously while being released of the performance con-strains impeded by sapphire.展开更多
基于Microfacet理论,当光线照射到粗糙表面时会发生显著的多次镜面反射现象,而传统偏振双向反射分布函数(Polarized Bidirectional Reflectance Distribution Function,pBRDF)未能很好地描述这种现象,为了得到更精确的pBRDF模型,更好地...基于Microfacet理论,当光线照射到粗糙表面时会发生显著的多次镜面反射现象,而传统偏振双向反射分布函数(Polarized Bidirectional Reflectance Distribution Function,pBRDF)未能很好地描述这种现象,为了得到更精确的pBRDF模型,更好地分析材料的偏振特性,本文在包含镜面反射、漫反射和定向漫反射的三分量pBRDF模型基础上,进一步定义了高阶微相位角与一阶相位角的关系。改进后的pBRDF模型不仅考虑了多次镜面反射的几何衰减因子,还引入了微相位角的定义,从而建立了一个更全面的高阶镜面反射pBRDF模型。通过比较不同的pBRDF模型,并结合偏振特性采集装置进行验证,实验结果表明,本文提出的模型优于其他模型,三阶模型效果普遍优于二阶。在偏振图像渲染中,峰值信噪比和结构相似性平均分别提升10.09%和2.97%,呈现更加真实的渲染效果。验证本文提出的高阶镜面反射pBRDF模型能够更准确地描述目标表面的偏振特性。展开更多
Due to the continuously increasing building and construction industry,sand has become one of the most questioned raw materials worldwide.However,the available amount of sand suitable for concrete production is orders ...Due to the continuously increasing building and construction industry,sand has become one of the most questioned raw materials worldwide.However,the available amount of sand suitable for concrete production is orders of magnitude lower that the demand and consumption.Even though desert sand is sufficiently available,it is not usable for realizing stable concrete due to its surface shape.Against this background,the suitability of energy-efficient‘cold'dielectric barrier discharge plasma operated at atmospheric pressure for improving the properties of concrete produced from desert sand was investigated in this contribution.It is shown that such plasma treatment allows for a certain roughening and re-shaping of sand grains.As a result,the mass flow of treated sand is decreased due to an improved wedging of sand grains.This leads to a certain increase in compressive strength of concrete samples.Even though this increase is marginal,the suitability of the applied type of plasma for modification of the geometry and surface chemistry of sand grains was proven,showing its basic potential for the treatment and preconditioning of sand used for concrete,mortar or plastering.展开更多
基金supported by the Special Funds for Major State Basic Research Project of China(Grant Nos.2011CB301900,2012CB619304,and 2010CB327504)the Hi-tech Research Project of China(Grant No.2011AA03A103)+4 种基金the National Nature Science Foundation of China(Grant Nos.60990311,61274003,60936004,and 61176063)the Program for New Century Excellent Talents in University of China(Grant No.NCET-11-0229)the Natural Science Foundation of Jiangsu Province of China(Grant No.BK2011010)the Funds of Key Laboratory of China(Grant No.9140C140102120C14)the Research Funds from NJU-Yangzhou Institute of Opto-electronics of China
文摘A significant enhancement in solar hydrogen generation efficiency has been achieved by inductive coupled etching （ICP） surface roughening treatment using nano-sized nickel mask. As much as 7 times improvement of photocurrent is demonstrated in comparison with a planar one fabricated from the same parent wafer. Under identical illumination conditions in HBr solution, the incident photon conversion efficiency （IPCE） shows an enhancement with a factor of 3, which even exceed 54% at 400 nm wavelength. We believe the enhancement is attributed to several facts including improvement in absorption, reacting area, carder localization and carrier lifetime.
文摘Impingement heat transfer from the rib roughened surface within 2 dimensional arrays of circular jet has been experimentally investigated.This investigation is intended here to include the flow and the heat transfer characteristics of the jet impinging on the rib roughened surface with initial crossflow for simulating the impingement cooling midchord region of the gas turbine aerofoils in case where an initial crossflow is presented.The study covered the ranges of crossflow G_(c)/G_(j)=0~0.55 under the conditions of Re_(j)=8000~11000 and Z/d=1.5~3.0 for smooth and rib roughened surfaces.The test results show that the impingement heat transfer from the rib roughened surface is considerably affected by the initial crossflow rate.The existence of the initial crossflow will improve the efficiency of the impingement heat transfer from the rib roughened surface within arrays of circular jet compared with that from the smooth surface.
基金Project supported by the Knowledge Innovation Program of ISCAS(No.08S4060000)
文摘Low resistance and thermally stable n-type contacts to N-polar GaN are essentially important for vertical light emitting diodes （VLEDs）. The electrical characteristics of VLEDs with n-type contacts on a roughened and flat N-polar surface have been compared. VLEDs with contacts deposited on a roughened surface exhibit lower leakage currents yet a higher operating voltage. Based on this, a new scheme by depositing metallization contacts on a selectively wet-etching roughened surface has been developed. Excellent electrical and optical characteristics have been achieved with this method. An aging test further confirmed its stability.
基金Project supported by the Natural Science Foundation of Beijing,China(No.4092007)the National High Technology Research and Development Program of China(No.2008AA03Z402)+1 种基金the Doctoral Program Foundation of Beijing,China(No.X0002013200801)the Eighth BJUT Technology Fund for Postgraduate Students,China
文摘By using the wafer bonding technique and wet etching process,a wafer bonded thin film AlGaInP LED with wet etched n-AlGaInP surfaces was fabricated.The morphology of the etched surface exhibits a pyramid-like feature.The wafer was cut into 270×270μm2 chips and then packaged into TO-18 without epoxy resin.With 20-mA current injection,the light intensity and output power of LED-Ⅰwith surface roughening respectively reach 315 mcd and 4.622 mW,which was 1.7 times higher than that of LED-Ⅱwithout surface roughening.The enhancement of output power in LED-Ⅰcan be attributed to the pyramid-like surface,which not only reduces the total internal reflection at the semiconductor-air interface but also effectively guides more photons into the escape angle for emission from the LED device.
文摘The morphology and lateral growth rate of isotactic polybutene-1(it-PB1)have been investigated for crystallization from the melt over a wide range of crystallization temperatures from 50 to 110℃.The morphology of it-PB1 crystals is a rounded shape at crystallization temperatures lower than 85℃,while lamellarsingle crystals possess faceted morphology at higher crystallization temperatures.The kinetic roughening transi-tion occurs around 85℃.The nucleation and growth mechanism for crystallization does not work below 85℃,since the growth face is rough.However,the growth rate shows the supercooling dependence derived from the nucleation and growth mechanism.The nucleation theory seems still to work even for rough surface growth.Possible mechanisms for the crystal growth of this polymer are discussed.
基金This work was supported by the National Natural Science Foundation of ChinaNational Laboratory for Structural Chemistry of Dynamical and Stable Species.
文摘The light beating technique (intensity correlation algorithm) was employed to analyze the Rayleigh scattering from the roughened Ag electrode in very dilute (10^(-4)M) pyrazine, pyridine and piperidine aqueous solutions containing KCl (0.1 M). The relaxation time is longer when the applied voltages are between-0.4 V and-0.8 V(vs. SCE) where the Raman effect also shows greater surface enhancement. Also observed was that for the piperidine case the relaxation time reaches its maximum at the more negative applied voltage. The origin of the relaxation is attributed mainly to the desorp- tion process of the pyrazine. pyridine and piperidine molecules off the roughened Ag electrode. An. electrostatic model was also proposed for the interpretation of these experimental observations.
基金Supported by the National High Technology Research and Development Program of China (Grant No. 2004AA311030)State Key Program of Basic Research of China (973) (Grant No. 20000683-02)+1 种基金Beijing Municipal Education Commission (Grant No. 2002kj018, Grant No. kz200510005003)Beijing Municipal Science and Technology Commission (Grant No. D0404003040221)
文摘An ultraviolet (UV) laser lift-off (LLO) technique was presented to form a roughened surface morphol-ogy on GaN membrane grown by metalorganic chemical vapor deposition (MOCVD). The etched sur-face showed cone-like structures on a free-standing GaN membrane. Based on the scanning electron microscopy (SEM) and atom force microscopy (AFM) measurements, the etching mechanism was proposed, which was related to the different decomposition depth caused by the dislocations in the GaN membrane. The etching efficiency and morphology of GaN by the LLO technique and the photo-electrochemical (PEC) wet etching technique was compared and analyzed. This roughed cone-like surface morphology by LLO can enhance the external efficiency of vertical structure n-side-up GaN-based light-emitting diodes (LEDs) simultaneously while being released of the performance con-strains impeded by sapphire.
文摘基于Microfacet理论,当光线照射到粗糙表面时会发生显著的多次镜面反射现象,而传统偏振双向反射分布函数(Polarized Bidirectional Reflectance Distribution Function,pBRDF)未能很好地描述这种现象,为了得到更精确的pBRDF模型,更好地分析材料的偏振特性,本文在包含镜面反射、漫反射和定向漫反射的三分量pBRDF模型基础上,进一步定义了高阶微相位角与一阶相位角的关系。改进后的pBRDF模型不仅考虑了多次镜面反射的几何衰减因子,还引入了微相位角的定义,从而建立了一个更全面的高阶镜面反射pBRDF模型。通过比较不同的pBRDF模型,并结合偏振特性采集装置进行验证,实验结果表明,本文提出的模型优于其他模型,三阶模型效果普遍优于二阶。在偏振图像渲染中,峰值信噪比和结构相似性平均分别提升10.09%和2.97%,呈现更加真实的渲染效果。验证本文提出的高阶镜面反射pBRDF模型能够更准确地描述目标表面的偏振特性。
基金funded by the Bundesministerium für Bildung und Forschung(Nos.13FH6I06IA and 13FH6I08IA)。
文摘Due to the continuously increasing building and construction industry,sand has become one of the most questioned raw materials worldwide.However,the available amount of sand suitable for concrete production is orders of magnitude lower that the demand and consumption.Even though desert sand is sufficiently available,it is not usable for realizing stable concrete due to its surface shape.Against this background,the suitability of energy-efficient‘cold'dielectric barrier discharge plasma operated at atmospheric pressure for improving the properties of concrete produced from desert sand was investigated in this contribution.It is shown that such plasma treatment allows for a certain roughening and re-shaping of sand grains.As a result,the mass flow of treated sand is decreased due to an improved wedging of sand grains.This leads to a certain increase in compressive strength of concrete samples.Even though this increase is marginal,the suitability of the applied type of plasma for modification of the geometry and surface chemistry of sand grains was proven,showing its basic potential for the treatment and preconditioning of sand used for concrete,mortar or plastering.
