If the upstream boundary conditions are prescribed based on the incident wave only, the time-dependent numerical models cannot effectively simulate the wave field when the physical or spurious reflected waves become s...If the upstream boundary conditions are prescribed based on the incident wave only, the time-dependent numerical models cannot effectively simulate the wave field when the physical or spurious reflected waves become significant. This paper describes carefully an approach to specifying the incident wave boundary conditions combined with a set sponge layer to absorb the reflected waves towards the incident boundary. Incorporated into a time-dependent numerical model, whose governing equations are the Boussinesq-type ones, the effectiveness of the approach is studied in detail. The general boundary conditions, describing the down-wave boundary conditions are also generalized to the case of random waves. The numerical model is in detail examined. The test cases include both the normal one-dimensional incident regular or random waves and the two-dimensional oblique incident regular waves. The calculated results show that the present approach is effective on damping the reflected waves towards the incident wave boundary.展开更多
In the nearshore, the wave field contains reflected and incident waves in which there is correlation between their phases due to the effect of reflection by some obstacles. Based on the extended eigenvector method (EE...In the nearshore, the wave field contains reflected and incident waves in which there is correlation between their phases due to the effect of reflection by some obstacles. Based on the extended eigenvector method (EEV) derived by Guan et al., a modified method (MEEV) is proposed as a general and practical approach to estimating directional spectra for the co-existent field of incident and reflected waves and a formula is given for direct calculation of the reflection coefficient. The results of numerical simulations show that MEEV is superior to EEV in resolution power, and the computed reflection coefficient agrees well with the real value within a certain range of incident angle.展开更多
This study presents a three-point method for separating incident and reflected waves to explain normally incident waves' propagating over a sloping bed. linear wave shoaling is used to determine changes in wave am...This study presents a three-point method for separating incident and reflected waves to explain normally incident waves' propagating over a sloping bed. linear wave shoaling is used to determine changes in wave amplitude and phase in response to variations of bathymetry. The wave reflection coefficient and incident amplitude are estimated from wave heights measured at three fixed wave gauges with unequal spacing. Sensitivity analysis demonstrates that the proposed method can predict the reflection and amplitude of waves over a sloping bed more accurately than the two-point method.展开更多
Femtosecond pump-terahertz probe studies of carrier dynamics in semi-insulating CaAs have been investigated in detail for various pump powers. It is observed that, at high pump powers, the reflection peaks flip to the...Femtosecond pump-terahertz probe studies of carrier dynamics in semi-insulating CaAs have been investigated in detail for various pump powers. It is observed that, at high pump powers, the reflection peaks flip to the opposite polarity and dramatically enhance as the pump arrival time approaches the reflected wave of the terahertz pulse. The abnormal polarity-flip and enhancement can be interpreted by the pump-induced enhancement in the photoconductivity of GaAs and half-wave loss. Moreover, the carrier relaxation processes and surface states filling in GaAs are also studied in these measurements.展开更多
Wave reflection is one of the key problems affecting wave simulation quality in ocean engineering basin. The deep ocean engineering basin is equipped with two-sided segmented wavemakers and two wave absorbing beaches,...Wave reflection is one of the key problems affecting wave simulation quality in ocean engineering basin. The deep ocean engineering basin is equipped with two-sided segmented wavemakers and two wave absorbing beaches, which are located opposite to wave generators to reduce wave reflection effects. When an oblique longcrested wave is made by two-sided segmented wavemakers in a wave basin, two bi-directional reflected waves with the same azimuth but opposite propagation directions are generated. According to this feature, based on the two-point approach developed by Goda, a method to separate an incident regular wave from two bi-directional reflected waves using three wave gauges is proposed. The validity of this method is proved by numerical composite waves. The results indicate that the method can separate incident wave from reflected waves effectively. The method can be used to determine the reflection coefficient and verify the capacity of wave absorbing beaches in deep ocean engineering basin.展开更多
In channel reservoirs,a quantitative characterization of landslide-generated impulse wave-structure interactions is essential for evaluating potential damage to infrastructure and dams.In this study,the problem of lan...In channel reservoirs,a quantitative characterization of landslide-generated impulse wave-structure interactions is essential for evaluating potential damage to infrastructure and dams.In this study,the problem of landslide-generated impulse waves that attack a vertical wall was investigated in a wave channel via a smooth particle hydrodynamics(SPH)method coupled with a Chrono model.The results indicated that the longitudinal velocity beneath the leading wave crest of an incident impulse wave deviated significantly from solitary wave theory.Moreover,the variation rate in the vertical velocity along the water column coincided with the theoretical prediction only for small wave amplitudes.Nevertheless,the maximum run-up height of an impulse wave can be accurately predicted via the solitary wave theory.Moreover,the maximum wall force during impulse wave-wall interaction was significantly larger than that during solitary wave reflection,particularly for high incident wave amplitudes.Overall,the present study demonstrated some striking differences in the interactions of landslide-generated impulse waves and solitary waves with a vertical wall.展开更多
The geological conditions for coal mining in China are complex,with various structural issues such as faults and collapsed columns seriously compromising the safety of coal mine production.In-seam wave exploration is ...The geological conditions for coal mining in China are complex,with various structural issues such as faults and collapsed columns seriously compromising the safety of coal mine production.In-seam wave exploration is an effective technique for acquiring detailed information on geological structures in coal seam working faces.However,the existing reflected in-seam wave imaging technique can no longer meet the exploration precision requirements,making it imperative to develop a new reflected in-seam wave imaging technique.This study applies the Gaussian beam summation(GBS)migration method to imaging coal seams'reflected in-seam wave data.Firstly,with regard to the characteristics of the reflected in-seam wave data,methods such as wavefield removal and enveloped superposition are employed for the corresponding wavefield separation,wave train compression and other processing of reflected in-seam waves.Thereafter,imaging is performed using the GBS migration technique.The feasibility and effectiveness of the proposed method for reflected in-seam wave imaging are validated by conducting GBS migration tests on 3D coal-seam fault models with different dip angles and throws.By applying the method to reflected in-seam wave data for an actual coal seam working face,accurate imaging of a fault structure is obtained,thereby validating its practicality.展开更多
Detecting subsurface fault structure is important for evaluating potential earthquake risks associated with active faults.In this study,we propose a new method to detect faults using reflected surface waves observed i...Detecting subsurface fault structure is important for evaluating potential earthquake risks associated with active faults.In this study,we propose a new method to detect faults using reflected surface waves observed in ambient noise cross correlation functions.Ambient noise tomography using direct surface waves obtained from ambient noise interferometry has been widely used to characterize active fault zones.In cases where a strong velocity contrast exists across the fault interface,fault-reflected surface waves are expected.We test this idea using a linear array deployed in the Suqian segment of Tanlu fault zone in Eastern China.The fault-reflected surface waves can be clearly seen in the cross-correlation functions of the ambient noise data,and the spatial position of the fault on the surface is close to the stations where the reflected signals first appear.Potentially reflected surface waves could also be used to infer the dip angle,fault zone thickness and the degree of velocity contrast across the fault by comparing synthetic and observed waveforms.展开更多
Diffracted seismic waves may be used to help identify and track geologically heterogeneous bodies or zones.However,the energy of diffracted waves is weaker than that of reflections.Therefore,the extraction of diffract...Diffracted seismic waves may be used to help identify and track geologically heterogeneous bodies or zones.However,the energy of diffracted waves is weaker than that of reflections.Therefore,the extraction of diffracted waves is the basis for the effective utilization of diffracted waves.Based on the difference in travel times between diffracted and reflected waves,we developed a method for separating the diffracted waves via singular value decomposition filters and presented an effective processing flowchart for diffracted wave separation and imaging.The research results show that the horizontally coherent difference between the reflected and diffracted waves can be further improved using normal move-out(NMO) correction.Then,a band-rank or high-rank approximation is used to suppress the reflected waves with better transverse coherence.Following,separation of reflected and diffracted waves is achieved after the filtered data are transformed into the original data domain by inverse NMO.Synthetic and field examples show that our proposed method has the advantages of fewer constraints,fast processing speed and complete extraction of diffracted waves.And the diffracted wave imaging results can effectively improve the identification accuracy of geological heterogeneous bodies or zones.展开更多
The selection of an appropriate basic detonation wave flow field is crucial for improving the performance and geometric design of standing detonation vehicles.This paper employs a detailed chemical reaction model and ...The selection of an appropriate basic detonation wave flow field is crucial for improving the performance and geometric design of standing detonation vehicles.This paper employs a detailed chemical reaction model and solves the unsteady axisymmetric Euler equation to study the characteristics of the Axisymmetric Inward Turning Curved Detonation Wave(AIT-CDW)flow field and the parameters affecting the stability of the wave system structure of AIT-CDW flow field.The numerical results demonstrate a radial compression effect in the AIT-CDW flow field.This effect causes the detonation wave to have a shorter initiation length than oblique detonation wave flow field and the detonation wave angle to gradually increase with the flow direction postdetonation.The AIT-CDW flow field is confined space,making it prone to normal detonation waves when the detonation wave reflects from the wall.This phenomenon is detrimental to the stability of the wave system structure in the flow field.It has been observed that increasing the center body radius and decreasing the fuel equivalent ratio can effectively reduce the height of the normal detonation wave or even eliminate it.Additionally,a well-designed generatrix shape of the center body can enhance airflow,reduce choked flow,and promote the stability of the wave structure in the flow field.展开更多
The reflection of oblique incident waves from breakwaters with a partially-perforated front wall is investigated. The fluid domain is divided into two sub-domains and the eigenfunction expansion method is applied to e...The reflection of oblique incident waves from breakwaters with a partially-perforated front wall is investigated. The fluid domain is divided into two sub-domains and the eigenfunction expansion method is applied to expand velocity potentials in each domain. In the eigen-expansion of the velocity potential, evanescent waves are included. Numerical results of the present model are compared with experimental data. The effect of porosity, the relative chamber width, the relative water depth in the wave absorbing chamber and the water depth in front of the structure are discussed.展开更多
A time-domain method, based on linear velocity potential theory, is presented to study the interaction between narrow-banded random waves and perforated structures. A simple relation is derived to estimate the jet len...A time-domain method, based on linear velocity potential theory, is presented to study the interaction between narrow-banded random waves and perforated structures. A simple relation is derived to estimate the jet length of flows through the perforated wall. The reflection coefficient of narrow banded random waves from perforated structures is calculated by assuming a Rayleigh distribution of the heights of incident random waves. For reflection of narrow-banded waves from a single-chamber perforated breakwater, a comparison of the predicted and measured reflection coefficients shows that the method presented in this paper can provide a prediction better than that of regular waves. Numerical results are also reported on the reflection of narrow-banded waves from multi-chamber perforated breakwaters.展开更多
The characteristics of wave transmission, reflection and energy dissipation of comb-type caisson breakwaters are studied through laboratory physical model tests. Regular and irregular waves, with a wide range of wave ...The characteristics of wave transmission, reflection and energy dissipation of comb-type caisson breakwaters are studied through laboratory physical model tests. Regular and irregular waves, with a wide range of wave heights and periods and a constant water depth, are considered. Different dimensions of each portion of the comb-type caisson breakwater are tested. Empirical formulae for calculating the reduction coefficient k, which is the ratio of horizontal wave force on unit length of the comb-type breakwater to that on unit length of the vertical wall breakwater, and for calculating the reflection coefficient of waves k, are obtained from the measurements. The comb-type caisson breakwater has been found to be very efficient in dissipating incident wave energy and in reducing wave reflection, and has already been used for the construction of an island breakwater in the Dayao Bay of Dalian Port, Liaoning Province, China. Compared with the cost of a common caisson breakwater, about 24.5% of the investment has been saved owing to the use of this comb-type breakwater.展开更多
The key problem in physical model tests with highly reflective structures is to prevent the multiple reflections between the reflective structures and the wave maker. An active absorption wave maker system is describe...The key problem in physical model tests with highly reflective structures is to prevent the multiple reflections between the reflective structures and the wave maker. An active absorption wave maker system is described and the representative frequency method for irregular waves is proposed in this paper. Physical model tests are conducted to verify the effectiveness of the proposed method.展开更多
In this paper, reflection and transmission coefficients of regular waves from/through perforated thin walls are investigated. Small scale laboratory tests have been performed in a wave flume firstly with single perfor...In this paper, reflection and transmission coefficients of regular waves from/through perforated thin walls are investigated. Small scale laboratory tests have been performed in a wave flume firstly with single perforated thin Plexiglas plates of various porosities. The plate is placed perpendicular to the flume with the height from the flume bottom to the position above water surface. With this thin wall in the flume wave overtopping is prohibited and incident waves are able to transmit. The porosities of the walls are achieved by perforating the plates with circular holes. Model settings with double perforated walls parallel to each other forming so called chamber system, have been also examined. Several parameters have been used for correlating the laboratory tests’ results. Experimental data are also compared with results from the numerical model by applying the multi-domain boundary element method （MDBEM） with linear wave theory. Wave energy dissipation due to the perforations of the thin wall has been represented by a simple yet effective porosity parameter in the model. The numerical model with the MDBEM has been further validated against the previously published data.展开更多
A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium...A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium, in which the solid matrix is filled with two weakly coupled fluids （liquid and gas）. The expressions for the amplitude reflection coefficients and the amplitude transmission coefficients are derived by using the potential method. The present derivation is subsequently applied to study the energy conversions among the incident, reflected, and transmitted wave modes. It is found that the reflection and transmission coefficients in the forms of amplitude ratios and energy ratios are functions of the incident angle, the liquid saturation, the frequency of the incident wave, and the elastic constants of the upper and lower media. Numerical results are presented graphically. The effects of the incident angle, the frequency, and the liquid saturation on the amplitude and the energy reflection and transmission coefficients are discussed. It is verified that in the transmission process, there is no energy dissipation at the interface.展开更多
The hydrodynamic efficiency of the vertical porous structures is investigated under regular waves by use of physical models. The hydrodynamic efficiency of the breakwater is presented in terms of the wave transmission...The hydrodynamic efficiency of the vertical porous structures is investigated under regular waves by use of physical models. The hydrodynamic efficiency of the breakwater is presented in terms of the wave transmission （kt）, reflection （kr） and energy dissipation （ka） coefficients. Different wave and structural parameters affecting the breakwater efficiency are tested. It is found that, the transmission coefficient （kt） decreases with the increase of the relative water depth （h/L）, the wave steepness （Hi^L）, the relative breakwater widths （B/L, B/h）, the relative breakwater height （D/h）, and the breakwater porosity （n）. The reflection coefficient （kr） takes the opposite trend of kt when D/h=l.25 and it decreases with the increasing h/L, HJL and B/L when D/h〈1.0. The dissipation coefficient （kd） increases with the increasing h/L, HilL and B/L when D/h〈_l.O and it decreases when D/h=l.25. In which, it is possible to achieve values ofkt smaller than 0.3, k~ larger than 0.5, and kd larger than 0.6 when D/h=1.25, B/h=0.6, h/L〉0.22, B/L〉O. 13, and H/L 〉0.04. Empirical equations are developed for the estimation of the transmission and reflection coefficients. The results of these equations are compared with other experimental and theoretical results and a reasonable agreement is obtained.展开更多
The present article represents an analysis of reflection of P-wave and SV-wave on the boundary of an isotropic and homogeneous generalized thermoelastic half-space when the boundary is stress-free as well as isotherma...The present article represents an analysis of reflection of P-wave and SV-wave on the boundary of an isotropic and homogeneous generalized thermoelastic half-space when the boundary is stress-free as well as isothermal. The modulus of elasticity is taken as a linear function of reference temperature. The basic governing equations are applied under four theories of the generalized thermoelasticity： Lord-Shulman （L-S） theory with one relaxation time, Green-Naghdi （G-N） theory without energy dissipation and Tzou theory with dual-phase-lag （DPL）, as well as the coupled thermoelasticity （CTE） theory. It is shown that there exist three plane waves, namely, a thermal wave, a P-wave and an SV-wave. The reflection from an isothermal stress-free surface is studied to obtain the reflection amplitude ratios of the reflected waves for the incidence of P- and SV-waves. The amplitude ratios variations with the angle of incident are shown graphically. Also the effects of reference temperature of the modulus of elasticity and dual-phase lags on the reflection amplitude ratios are discussed numerically.展开更多
An experimental study and a numerical simulation were conducted to investigate the mechanical and thermodynamic processes involved in the interaction between shock waves and low density foam. The experiment was done i...An experimental study and a numerical simulation were conducted to investigate the mechanical and thermodynamic processes involved in the interaction between shock waves and low density foam. The experiment was done in a stainless shock tube (80 mm in inner diameter, 10 mm in wall thickness and 5 360 mm in length). The velocities of the incident and reflected compression waves in the foam were measured by using piezo-ceramic pressure sensors. The end-wall peak pressure behind the reflected wave in the foam was measured by using a crystal piezoelectric sensor. It is suggested that the high end-wall pressure may be caused by a rapid contact between the foam and the end-wall surface. Both open-cell and closed-cell foams with different length and density were tested. Through comparing the numerical and experimental end-wall pressure, the permeability coefficients α and β are quantitatively determined.展开更多
This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the...This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the normally-incident reflected and transmitted ultrasonic waves. The analytical formula of the layer thickness related to the measured trans- mitted transfer functions is derived. The two determination steps of the four layer parameters are developed, in which acoustic impedance, time-of-flight and attenuation are first determined by the reflected transfer functions. Using the derived formula, it successively calculates and determines the layer thickness, longitudinal velocity and mass density by the measured transmitted transfer functions. According to the two determination steps, a more feasible and simplified measurement setups is described. It is found that only three signals （the reference waves, the reflected and transmitted waves） need to be recorded in the whole measurement for the determination of the four layer parameters. A study of the stability of the determination method against the experimental noises and the error analysis of the four layer parameters are made. This study lays the theoretical foundation of the practical measurement of a linear-viscoelastic thin layer.展开更多
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51079082 and 40676053)the LRET through the joint centre involving University College London,Shanghai JiaoTong University and Harbin Engineering University
文摘If the upstream boundary conditions are prescribed based on the incident wave only, the time-dependent numerical models cannot effectively simulate the wave field when the physical or spurious reflected waves become significant. This paper describes carefully an approach to specifying the incident wave boundary conditions combined with a set sponge layer to absorb the reflected waves towards the incident boundary. Incorporated into a time-dependent numerical model, whose governing equations are the Boussinesq-type ones, the effectiveness of the approach is studied in detail. The general boundary conditions, describing the down-wave boundary conditions are also generalized to the case of random waves. The numerical model is in detail examined. The test cases include both the normal one-dimensional incident regular or random waves and the two-dimensional oblique incident regular waves. The calculated results show that the present approach is effective on damping the reflected waves towards the incident wave boundary.
文摘In the nearshore, the wave field contains reflected and incident waves in which there is correlation between their phases due to the effect of reflection by some obstacles. Based on the extended eigenvector method (EEV) derived by Guan et al., a modified method (MEEV) is proposed as a general and practical approach to estimating directional spectra for the co-existent field of incident and reflected waves and a formula is given for direct calculation of the reflection coefficient. The results of numerical simulations show that MEEV is superior to EEV in resolution power, and the computed reflection coefficient agrees well with the real value within a certain range of incident angle.
文摘This study presents a three-point method for separating incident and reflected waves to explain normally incident waves' propagating over a sloping bed. linear wave shoaling is used to determine changes in wave amplitude and phase in response to variations of bathymetry. The wave reflection coefficient and incident amplitude are estimated from wave heights measured at three fixed wave gauges with unequal spacing. Sensitivity analysis demonstrates that the proposed method can predict the reflection and amplitude of waves over a sloping bed more accurately than the two-point method.
基金Project supported by the National Basic Research Program of China (973 Program) (Grant Nos 2007CB310408 and2006CB302901)the National Natural Science Foundation of China (Grant No 10804077)+2 种基金Science Foundation of Beijing Municipal Commission of Education (Grant No KM200910028006)Funding Project for Academic Human Resources Development in Institutions of Higher Learning under the Jurisdiction of Beijing Municipalitysupported by State Key Laboratory of Functional Materials for Informatics,Shanghai Institute of Microsystem and Information Technology,the Chinese Academy of Sciences
文摘Femtosecond pump-terahertz probe studies of carrier dynamics in semi-insulating CaAs have been investigated in detail for various pump powers. It is observed that, at high pump powers, the reflection peaks flip to the opposite polarity and dramatically enhance as the pump arrival time approaches the reflected wave of the terahertz pulse. The abnormal polarity-flip and enhancement can be interpreted by the pump-induced enhancement in the photoconductivity of GaAs and half-wave loss. Moreover, the carrier relaxation processes and surface states filling in GaAs are also studied in these measurements.
基金the National Natural Science Foundation of China(No.51239007)
文摘Wave reflection is one of the key problems affecting wave simulation quality in ocean engineering basin. The deep ocean engineering basin is equipped with two-sided segmented wavemakers and two wave absorbing beaches, which are located opposite to wave generators to reduce wave reflection effects. When an oblique longcrested wave is made by two-sided segmented wavemakers in a wave basin, two bi-directional reflected waves with the same azimuth but opposite propagation directions are generated. According to this feature, based on the two-point approach developed by Goda, a method to separate an incident regular wave from two bi-directional reflected waves using three wave gauges is proposed. The validity of this method is proved by numerical composite waves. The results indicate that the method can separate incident wave from reflected waves effectively. The method can be used to determine the reflection coefficient and verify the capacity of wave absorbing beaches in deep ocean engineering basin.
基金financially supported by the Natural Science Foundation of Chongqing,China(Grant No.cstc2020jcyj-bshX0043)POWERCHINA Science and Technology Project(Grant No.DJ-ZDXM-2022-28)Yunnan Fundamental Research Projects(Grant No.202401CF070042).
文摘In channel reservoirs,a quantitative characterization of landslide-generated impulse wave-structure interactions is essential for evaluating potential damage to infrastructure and dams.In this study,the problem of landslide-generated impulse waves that attack a vertical wall was investigated in a wave channel via a smooth particle hydrodynamics(SPH)method coupled with a Chrono model.The results indicated that the longitudinal velocity beneath the leading wave crest of an incident impulse wave deviated significantly from solitary wave theory.Moreover,the variation rate in the vertical velocity along the water column coincided with the theoretical prediction only for small wave amplitudes.Nevertheless,the maximum run-up height of an impulse wave can be accurately predicted via the solitary wave theory.Moreover,the maximum wall force during impulse wave-wall interaction was significantly larger than that during solitary wave reflection,particularly for high incident wave amplitudes.Overall,the present study demonstrated some striking differences in the interactions of landslide-generated impulse waves and solitary waves with a vertical wall.
基金supported by the National Natural Science Foundation of China(Grant No.42174157)the CAGS Research Fund(Grant No.JKY202216)the Chinese Geological Survey Project(Grant Nos.DD20230008,DD20233002).
文摘The geological conditions for coal mining in China are complex,with various structural issues such as faults and collapsed columns seriously compromising the safety of coal mine production.In-seam wave exploration is an effective technique for acquiring detailed information on geological structures in coal seam working faces.However,the existing reflected in-seam wave imaging technique can no longer meet the exploration precision requirements,making it imperative to develop a new reflected in-seam wave imaging technique.This study applies the Gaussian beam summation(GBS)migration method to imaging coal seams'reflected in-seam wave data.Firstly,with regard to the characteristics of the reflected in-seam wave data,methods such as wavefield removal and enveloped superposition are employed for the corresponding wavefield separation,wave train compression and other processing of reflected in-seam waves.Thereafter,imaging is performed using the GBS migration technique.The feasibility and effectiveness of the proposed method for reflected in-seam wave imaging are validated by conducting GBS migration tests on 3D coal-seam fault models with different dip angles and throws.By applying the method to reflected in-seam wave data for an actual coal seam working face,accurate imaging of a fault structure is obtained,thereby validating its practicality.
基金supported by the National Key R&D Program of China(2018YFC1504102)National Natural Science Foundation of China(41961134001).
文摘Detecting subsurface fault structure is important for evaluating potential earthquake risks associated with active faults.In this study,we propose a new method to detect faults using reflected surface waves observed in ambient noise cross correlation functions.Ambient noise tomography using direct surface waves obtained from ambient noise interferometry has been widely used to characterize active fault zones.In cases where a strong velocity contrast exists across the fault interface,fault-reflected surface waves are expected.We test this idea using a linear array deployed in the Suqian segment of Tanlu fault zone in Eastern China.The fault-reflected surface waves can be clearly seen in the cross-correlation functions of the ambient noise data,and the spatial position of the fault on the surface is close to the stations where the reflected signals first appear.Potentially reflected surface waves could also be used to infer the dip angle,fault zone thickness and the degree of velocity contrast across the fault by comparing synthetic and observed waveforms.
基金supported by the National Natural Science Foundation of China(41874123)Shaanxi Province Natural Science Basic Research Project(2017JZ007)PetroChina Innovation Foundation(2014D-5006-0303)。
文摘Diffracted seismic waves may be used to help identify and track geologically heterogeneous bodies or zones.However,the energy of diffracted waves is weaker than that of reflections.Therefore,the extraction of diffracted waves is the basis for the effective utilization of diffracted waves.Based on the difference in travel times between diffracted and reflected waves,we developed a method for separating the diffracted waves via singular value decomposition filters and presented an effective processing flowchart for diffracted wave separation and imaging.The research results show that the horizontally coherent difference between the reflected and diffracted waves can be further improved using normal move-out(NMO) correction.Then,a band-rank or high-rank approximation is used to suppress the reflected waves with better transverse coherence.Following,separation of reflected and diffracted waves is achieved after the filtered data are transformed into the original data domain by inverse NMO.Synthetic and field examples show that our proposed method has the advantages of fewer constraints,fast processing speed and complete extraction of diffracted waves.And the diffracted wave imaging results can effectively improve the identification accuracy of geological heterogeneous bodies or zones.
基金supported by the National Natural Science Foundation of China(Nos.U20A2069,62376234 and 123B2037)the Advanced Aero-Power Innovation Workstation,China(No.HKCX2024-01-017)。
文摘The selection of an appropriate basic detonation wave flow field is crucial for improving the performance and geometric design of standing detonation vehicles.This paper employs a detailed chemical reaction model and solves the unsteady axisymmetric Euler equation to study the characteristics of the Axisymmetric Inward Turning Curved Detonation Wave(AIT-CDW)flow field and the parameters affecting the stability of the wave system structure of AIT-CDW flow field.The numerical results demonstrate a radial compression effect in the AIT-CDW flow field.This effect causes the detonation wave to have a shorter initiation length than oblique detonation wave flow field and the detonation wave angle to gradually increase with the flow direction postdetonation.The AIT-CDW flow field is confined space,making it prone to normal detonation waves when the detonation wave reflects from the wall.This phenomenon is detrimental to the stability of the wave system structure in the flow field.It has been observed that increasing the center body radius and decreasing the fuel equivalent ratio can effectively reduce the height of the normal detonation wave or even eliminate it.Additionally,a well-designed generatrix shape of the center body can enhance airflow,reduce choked flow,and promote the stability of the wave structure in the flow field.
基金by Joint Fund of the National Natural Science Foundation of China the Hong Kong Science Research Bureau (49910161985)+1 种基金the National Natural Science Foundation of China (50025924,50179004)the Research Fund for the Development of harbor engineeri
文摘The reflection of oblique incident waves from breakwaters with a partially-perforated front wall is investigated. The fluid domain is divided into two sub-domains and the eigenfunction expansion method is applied to expand velocity potentials in each domain. In the eigen-expansion of the velocity potential, evanescent waves are included. Numerical results of the present model are compared with experimental data. The effect of porosity, the relative chamber width, the relative water depth in the wave absorbing chamber and the water depth in front of the structure are discussed.
基金The project partially supported by the Hong Kong Research Grant Council (DAG03/04.EG39, DAG04/05.EG32)
文摘A time-domain method, based on linear velocity potential theory, is presented to study the interaction between narrow-banded random waves and perforated structures. A simple relation is derived to estimate the jet length of flows through the perforated wall. The reflection coefficient of narrow banded random waves from perforated structures is calculated by assuming a Rayleigh distribution of the heights of incident random waves. For reflection of narrow-banded waves from a single-chamber perforated breakwater, a comparison of the predicted and measured reflection coefficients shows that the method presented in this paper can provide a prediction better than that of regular waves. Numerical results are also reported on the reflection of narrow-banded waves from multi-chamber perforated breakwaters.
基金This paper presents part of the achievement in the China National Key Project"Construction Techniques for Breakwa-ters in Deep Water"(96-415-02-03)
文摘The characteristics of wave transmission, reflection and energy dissipation of comb-type caisson breakwaters are studied through laboratory physical model tests. Regular and irregular waves, with a wide range of wave heights and periods and a constant water depth, are considered. Different dimensions of each portion of the comb-type caisson breakwater are tested. Empirical formulae for calculating the reduction coefficient k, which is the ratio of horizontal wave force on unit length of the comb-type breakwater to that on unit length of the vertical wall breakwater, and for calculating the reflection coefficient of waves k, are obtained from the measurements. The comb-type caisson breakwater has been found to be very efficient in dissipating incident wave energy and in reducing wave reflection, and has already been used for the construction of an island breakwater in the Dayao Bay of Dalian Port, Liaoning Province, China. Compared with the cost of a common caisson breakwater, about 24.5% of the investment has been saved owing to the use of this comb-type breakwater.
基金TheworkwasfinanciallysupportedbytheNationalNaturalScienceFoundationofChina(GrantNo .5 990 90 0 1)andFokYingTungEducationFoundation (No .810 68)
文摘The key problem in physical model tests with highly reflective structures is to prevent the multiple reflections between the reflective structures and the wave maker. An active absorption wave maker system is described and the representative frequency method for irregular waves is proposed in this paper. Physical model tests are conducted to verify the effectiveness of the proposed method.
基金the Yildiz Technical University Research Fund for financially supporting this work
文摘In this paper, reflection and transmission coefficients of regular waves from/through perforated thin walls are investigated. Small scale laboratory tests have been performed in a wave flume firstly with single perforated thin Plexiglas plates of various porosities. The plate is placed perpendicular to the flume with the height from the flume bottom to the position above water surface. With this thin wall in the flume wave overtopping is prohibited and incident waves are able to transmit. The porosities of the walls are achieved by perforating the plates with circular holes. Model settings with double perforated walls parallel to each other forming so called chamber system, have been also examined. Several parameters have been used for correlating the laboratory tests’ results. Experimental data are also compared with results from the numerical model by applying the multi-domain boundary element method （MDBEM） with linear wave theory. Wave energy dissipation due to the perforations of the thin wall has been represented by a simple yet effective porosity parameter in the model. The numerical model with the MDBEM has been further validated against the previously published data.
文摘A linear viscoporoelastic model is developed to describe the problem of reflection and transmission of an obliquely incident plane P-wave at the interface between an elastic solid and an unsaturated poroelastic medium, in which the solid matrix is filled with two weakly coupled fluids （liquid and gas）. The expressions for the amplitude reflection coefficients and the amplitude transmission coefficients are derived by using the potential method. The present derivation is subsequently applied to study the energy conversions among the incident, reflected, and transmitted wave modes. It is found that the reflection and transmission coefficients in the forms of amplitude ratios and energy ratios are functions of the incident angle, the liquid saturation, the frequency of the incident wave, and the elastic constants of the upper and lower media. Numerical results are presented graphically. The effects of the incident angle, the frequency, and the liquid saturation on the amplitude and the energy reflection and transmission coefficients are discussed. It is verified that in the transmission process, there is no energy dissipation at the interface.
文摘The hydrodynamic efficiency of the vertical porous structures is investigated under regular waves by use of physical models. The hydrodynamic efficiency of the breakwater is presented in terms of the wave transmission （kt）, reflection （kr） and energy dissipation （ka） coefficients. Different wave and structural parameters affecting the breakwater efficiency are tested. It is found that, the transmission coefficient （kt） decreases with the increase of the relative water depth （h/L）, the wave steepness （Hi^L）, the relative breakwater widths （B/L, B/h）, the relative breakwater height （D/h）, and the breakwater porosity （n）. The reflection coefficient （kr） takes the opposite trend of kt when D/h=l.25 and it decreases with the increasing h/L, HJL and B/L when D/h〈1.0. The dissipation coefficient （kd） increases with the increasing h/L, HilL and B/L when D/h〈_l.O and it decreases when D/h=l.25. In which, it is possible to achieve values ofkt smaller than 0.3, k~ larger than 0.5, and kd larger than 0.6 when D/h=1.25, B/h=0.6, h/L〉0.22, B/L〉O. 13, and H/L 〉0.04. Empirical equations are developed for the estimation of the transmission and reflection coefficients. The results of these equations are compared with other experimental and theoretical results and a reasonable agreement is obtained.
基金funded by the Deanship of Scientific Research(DSR),King Abdulaziz University,Jeddah,under grant No.(363/130/1431)
文摘The present article represents an analysis of reflection of P-wave and SV-wave on the boundary of an isotropic and homogeneous generalized thermoelastic half-space when the boundary is stress-free as well as isothermal. The modulus of elasticity is taken as a linear function of reference temperature. The basic governing equations are applied under four theories of the generalized thermoelasticity： Lord-Shulman （L-S） theory with one relaxation time, Green-Naghdi （G-N） theory without energy dissipation and Tzou theory with dual-phase-lag （DPL）, as well as the coupled thermoelasticity （CTE） theory. It is shown that there exist three plane waves, namely, a thermal wave, a P-wave and an SV-wave. The reflection from an isothermal stress-free surface is studied to obtain the reflection amplitude ratios of the reflected waves for the incidence of P- and SV-waves. The amplitude ratios variations with the angle of incident are shown graphically. Also the effects of reference temperature of the modulus of elasticity and dual-phase lags on the reflection amplitude ratios are discussed numerically.
文摘An experimental study and a numerical simulation were conducted to investigate the mechanical and thermodynamic processes involved in the interaction between shock waves and low density foam. The experiment was done in a stainless shock tube (80 mm in inner diameter, 10 mm in wall thickness and 5 360 mm in length). The velocities of the incident and reflected compression waves in the foam were measured by using piezo-ceramic pressure sensors. The end-wall peak pressure behind the reflected wave in the foam was measured by using a crystal piezoelectric sensor. It is suggested that the high end-wall pressure may be caused by a rapid contact between the foam and the end-wall surface. Both open-cell and closed-cell foams with different length and density were tested. Through comparing the numerical and experimental end-wall pressure, the permeability coefficients α and β are quantitatively determined.
基金supported by the National Natural Science Foundation of China (Grant Nos. 10534040 and 40674059)the State Key Laboratory of Acoustics (IACAS) (Grant No. 200807)
文摘This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the normally-incident reflected and transmitted ultrasonic waves. The analytical formula of the layer thickness related to the measured trans- mitted transfer functions is derived. The two determination steps of the four layer parameters are developed, in which acoustic impedance, time-of-flight and attenuation are first determined by the reflected transfer functions. Using the derived formula, it successively calculates and determines the layer thickness, longitudinal velocity and mass density by the measured transmitted transfer functions. According to the two determination steps, a more feasible and simplified measurement setups is described. It is found that only three signals （the reference waves, the reflected and transmitted waves） need to be recorded in the whole measurement for the determination of the four layer parameters. A study of the stability of the determination method against the experimental noises and the error analysis of the four layer parameters are made. This study lays the theoretical foundation of the practical measurement of a linear-viscoelastic thin layer.
