Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the ap...Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the application of conventional control strategies for stability operation face several challenges due to the uncontrollability of the DR.In this paper,a coordinated control strategy of offshore wind farms using the DR-HVDC transmission technology to connect with the onshore grid,is investigated.A novel coordinated control strategy for DR-HVDC is proposed based on the analysis of the DC current control ability of the full-bridge-based modular multilevel converter(FB-MMC)at the onshore station and the input and output characteristics of the diode rectifier at the offshore.Considering the characteristics of operation stability and decoupling between reactive power and active power,a simplified design based on double-loop droop control for offshore AC voltage is proposed after power flow and voltage–current(I–V)characteristics of the offshore wind farm being analyzed.Furthermore,the impact of onshore AC fault to offshore wind farm is analyzed,and a fast fault detection and protection strategy without relying on communication is proposed.Case studies carried out by PSCAD/EMTDC verify the effectiveness of the proposed control strategy for the start up,power fluctuation,and onshore and offshore fault conditions.展开更多
The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence co...The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence components,the proposed nonlinear control strategy suppresses the twice frequency ripple and guarantees the dynamic response characteristic at the same time.Thanks to the proposed nonlinear control strategy,the DC bus capacitor can be reduced a lot since the voltage ripple and drop can be suppressed.A 10 kW Vienna rectifier is built to verify the proposed control strategy.After applying the proposed nonlinear control strategy,the voltage ripple is only7 V and decreases over 75%over the traditional PI control when the unbalanced degree is 20%.The voltage drop can be reduced about 80%than former control strategy which is helpful to reduce the DC bus capacitor and achieve higher power density.The volume of the capacitor can be reduced by 83.3%with the new control method.展开更多
The comprehensive understanding of the structure-dependent electrostatic discharge behaviors in a conventional diode-triggered silicon controlled rectifier （DTSCR） is presented in this paper. Combined with the devic...The comprehensive understanding of the structure-dependent electrostatic discharge behaviors in a conventional diode-triggered silicon controlled rectifier （DTSCR） is presented in this paper. Combined with the device simulation, a mathematical model is built to get a more in-depth insight into this phenomenon. The theoretical studies are verified by the transmission-line-pulsing （TLP） test results of the modified DTSCR structure, which is realized in a 65-nm complementary metal-oxide-semiconductor （CMOS） process. The detailed analysis of the physical mechanism is used to provide predictions as the DTSCR-based protection scheme is required. In addition, a method is also presented to achieve the tradeoff between the leakage and trigger voltage in DTSCR.展开更多
In this paper, a voltage oriented control strategy for three-level PWM rectifier based on Sliding Mode Control (SMC) is introduced in order to obtain fast and accurate response of dc-bus voltage. To verify the validit...In this paper, a voltage oriented control strategy for three-level PWM rectifier based on Sliding Mode Control (SMC) is introduced in order to obtain fast and accurate response of dc-bus voltage. To verify the validity of the analysis and the feasibility of the proposed control method a set of simulation tests have been conducted using Matlab/Simulink. The simulation results show that compared to the conventional PI controller, the SMC can reduce drastically the three-level rectifier’s voltage fluctuation and improve the dynamic response of dc-bus significantly.展开更多
To solve the problem of harmonic pollution to the power grid that caused by traditional diode rectifier and phase controlled rectifier, the unit power factor PWM rectifier is designed. The topology structure of the re...To solve the problem of harmonic pollution to the power grid that caused by traditional diode rectifier and phase controlled rectifier, the unit power factor PWM rectifier is designed. The topology structure of the rectifier circuit is introduced and the double closed-loop control strategy in three-phase stationary coordinate system is analyzed. For the deficiency of control strategy, the control strategy in two-phase synchronous rotating coordinate system is proposed. This makes the independent control of active current and reactive current to be realized. The simulation model of the PWM rectifier is built and the effectiveness of the control method proposed in this paper is verified by simulation.展开更多
Due to attractive features,including high efficiency,low device stress,and ability to boost voltage,a Vienna rectifier is commonly employed as a battery charger in an electric vehicle(EV).However,the 6k±1 harmoni...Due to attractive features,including high efficiency,low device stress,and ability to boost voltage,a Vienna rectifier is commonly employed as a battery charger in an electric vehicle(EV).However,the 6k±1 harmonics in the acside current of the Vienna rectifier deteriorate theTHDof the ac current,thus lowering the power factor.Therefore,the current closed-loop for suppressing 6k±1 harmonics is essential tomeet the desired total harmonic distortion(THD).Fast repetitive control(FRC)is generally adopted;however,the deviation of power grid frequency causes delay link in the six frequency fast repetitive control to become non-integer and the tracking performance to deteriorate.This paper presents the detailed parameter design and calculation of fractional order fast repetitive controller(FOFRC)for the non-integer delay link.The finite polynomial approximates the non-integer delay link through the Lagrange interpolation method.By comparing the frequency characteristics of traditional repetitive control,the effectiveness of the FOFRC strategy is verified.Finally,simulation and experiment validate the steadystate performance and harmonics suppression ability of FOFRC.展开更多
A diode-triggered silicon controlled rectifier (DTSCR) is being developed as an electrostatic discharge (ESD) pro- tection device for low voltage applications. However, DTSCR leaks high current during normal operation...A diode-triggered silicon controlled rectifier (DTSCR) is being developed as an electrostatic discharge (ESD) pro- tection device for low voltage applications. However, DTSCR leaks high current during normal operation due to the Darlington effect of the triggering-assist diode string. In this study, two types of diode string triggered SCRs are designed for low leakage consideration; the modified diode string and composite polysilicon diode string triggered SCRs (MDTSCR & PDTSCR). Com- pared with the conventional DTSCR (CDTSCR), the MDTSCR has a much lower substrate leakage current with a relatively large silicon cost, and the PDTSCR has a much lower substrate leakage current with similar area and shows good leakage performance at a high temperature. Other DTSCR ESD properties are also investigated, especially regarding their layout, triggering voltage and failure current.展开更多
In predictive direct power control(PDPC)system of three-phase pulse width modulation(PWM)rectifier,grid voltage sensor makes the whole system more complex and costly.Therefore,third-order generalized integrator(TOGI)i...In predictive direct power control(PDPC)system of three-phase pulse width modulation(PWM)rectifier,grid voltage sensor makes the whole system more complex and costly.Therefore,third-order generalized integrator(TOGI)is used to generate orthogonal signals with the same frequency to estimate the grid voltage.In addition,in view of the deviation between actual and reference power in the three-phase PWM rectifier traditional PDPC strategy,a power correction link is designed to correct the power reference value.The grid voltage sensor free algorithm based on TOGI and the corrected PDPC strategy are applied to three-phase PWM rectifier and simulated on the simulation platform.Simulation results show that the proposed method can effectively eliminate the power tracking deviation and the grid voltage.The effectiveness of the proposed method is verified by comparing the simulation results.展开更多
Aiming at the PWM rectifier control strategy of sliding mode control, steady state performance weak Hamiltonian control dynamic tracking performance is poor, the coordinated compound control is proposed, the feedback ...Aiming at the PWM rectifier control strategy of sliding mode control, steady state performance weak Hamiltonian control dynamic tracking performance is poor, the coordinated compound control is proposed, the feedback linearization controller and sliding mode controller Hamiltonian system is obtained, and the design of a coordinated control strategy. In order to verify the accuracy of this method, MATLAB/Simulink is used for simulation analysis. The simulation results show that the composite control can achieve the coordinated dynamic rapid tracking and constant DC output and unit power factor operation, and satisfy the control requirements of the rectifier, effectively reducing the disturbance effect on the system. Compared with Hamiltonian control, the proposed method combines the advantages of the two methods, which have the fast tracking performance and excellent steady-state characteristics, and the research prospect is broad.展开更多
This paper presents a PFCVF (Power Factor Correction) rectifier that uses a variable frequency source for alternators for electric and hybrid vehicles application. In such application, the frequency of the signal in t...This paper presents a PFCVF (Power Factor Correction) rectifier that uses a variable frequency source for alternators for electric and hybrid vehicles application. In such application, the frequency of the signal in the alternator changes according to the vehicle speed, more over the loading effect on the alternator introduces harmonic currents and increases the alternator apparent power requirements. To overcome these problems and aiming more stability and better design of the alternator, a new third harmonic injection technique is proposed. This technique allows to preserve a good THD (Total Harmonic Distortion) of the input source at any frequency and to decrease losses in semiconductors switches, thereby allowing more stability and reducing the apparent power requirements. A comparative study between the standard and the new technique is made and highlights the effectiveness of the new design. A detailed analysis of the proposed topology is presented and simulations as well as experimental results are shown.展开更多
A control strategy of repetitive control without inductorance decoupling was proposed to address the problem of high total harmonic distortion(THD)rate of the network-side current caused by the reduced stability of th...A control strategy of repetitive control without inductorance decoupling was proposed to address the problem of high total harmonic distortion(THD)rate of the network-side current caused by the reduced stability of the rectifier module of the DC charging pile under weak grid as well as the dead zone and nonlinearity of switching devices during charging.Firstly,the parallel repetitive control was constructed in the inner current loop,and the proportional-integral(PI)+repetitive controller based on parallel structure was designed.For system compensation,a second-order low-pass filter was selected to correct the system,and the network-side current harmonics were actively suppressed without increasing the filtering device,which effectively improves the quality of grid-connected current.Secondly,based on the synthetic vector method,the controller parameters were designed to realize the elimination of main pole by establishing two synchronous rotation coordinate system vector differential equations,so as to realize the inductanceless decoupling to cope with the influence of network-side inductance fluctuation on the stability of the control system under weak grid.By theoretical analysis and simulation,the proposed control strategy was embedded into the self-developed digital signal processor for the rectifier module of DC charging pile,simulated dynamic and steady-state operation experiments were conducted,and comparative analysis was performed to prove the feasibility of the proposed control strategy.展开更多
Power factor correction (PFC) is widely used in many industry fields. In this paper, a novel multiplexed and paralleled PFC rectifier (MPPR) is proposed. Compared with the paralleled traditional six-switch buck-type P...Power factor correction (PFC) is widely used in many industry fields. In this paper, a novel multiplexed and paralleled PFC rectifier (MPPR) is proposed. Compared with the paralleled traditional six-switch buck-type PFC rectifier (SSBPR), the proposed one uses fewer switches by multiplexing. And it is beneficial for system hardware design. The commutation states of the rectifier are illustrated in detail. By comparing the active power switches, it is shown that the efficiency of the rectifier is similar to that of the traditional paralleled one. Because the commutation states for the upper and lower parts of the rectifier are different, the controller of the converter is analyzed step by step. The forward duties and the inductor current references are discussed by considering the different input voltages of the upper and lower parts of the MPPR. Then the controller is presented and analyzed. Finally the effectiveness of the MPPR is verified by experiments.展开更多
In this paper, the modified LCC type of series-parallel Resonant Converter (RC) was designed and state-space modeling analysis was implemented. In this proposed converter, one leg of full bridge diode rectifier is rep...In this paper, the modified LCC type of series-parallel Resonant Converter (RC) was designed and state-space modeling analysis was implemented. In this proposed converter, one leg of full bridge diode rectifier is replaced with Synchronous Rectifier (SR) switches. The proposed LCC converter is controlled using frequency modulation in the nominal state. During hold-up time, the SRswitches control is changed from in-phase to phase-shifted gate signal to obtain high DC voltage conversion ratio. Furthermore, the closed loop PI and fuzzy provide control on the output side without decreasing the switching frequency. The parameter such as conduction loss on primary and secondary side, switching loss, core and copper also reduced. Simultaneously, the efficiency is increased about 94.79 is realized by this scheme. The proposed converter with an input of 40 V is built to produce an output of 235 V with the help of ZVS boost converter [1] even under line and load disturbances. As a comparison, the closed loop fuzzy controller performance is feasible and less sensitive than PI controller.展开更多
The performance of the current stabilization control system in an aluminum smelter affects the quality and the quantity of the electrolytic products. This paper elaborates the power supply, in which the diode rectifie...The performance of the current stabilization control system in an aluminum smelter affects the quality and the quantity of the electrolytic products. This paper elaborates the power supply, in which the diode rectifiers and the self-saturable reactors could keep the series current stable, then describes the basic principle of the rectifier unit control and the series current control. A coordinate strategy is proposed to keep the series current stable, the self-saturable reactors are controlled by a proportional-integral control scheme and the on load tap changers of transformer are triggered by the errors between the setting value of the series voltage and the measured values of the series voltage. Simulation results on PSCAD/EMTDC show that the effectiveness of the proposed strategy to keep the series current stable.展开更多
This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-ph...This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-phase half-controlled rectifier has been designed to control and convert the AC power into DC power.In addition,two types of direct current converters have been used in this paper which are a buck and bidirectional DC/DC converters.These systems adjust the output voltage to be lower or higher than the input voltage.In the buck converters,the main switch operates in conduction or cut-off mode and is triggered by a Pulse-Width Modulated(PWM)signal.The output and input voltage levels ratio are used to calculate thePWMsignal’s duty cycle.Therefore,the duty cycle indicates the operation mode of the converter in steady-state operation.In this study,we analyze and control of a buck converter with the PWM signal.Besides,the bidirectional DC/DC converter has been achieved and optimized by PI control methods to control the battery charging and discharging modes.The simulation has been applied via the Matlab/Simulink environment.The results show the activity of each part of the designed circuits starting from the converters and the battery control system in charge and discharge modes.展开更多
MPI（multishot pellet injector） was imported from Russia about ten years ago. During the year＇s operation in HL-1M, most electrical equipments were repaired. Since the components are non-standard, so it is difficult...MPI（multishot pellet injector） was imported from Russia about ten years ago. During the year＇s operation in HL-1M, most electrical equipments were repaired. Since the components are non-standard, so it is difficult to maintain. To fueling experiment meet the requirement of in HL-2A. The power supplies of fast valve and a programmable controller for shooting pellets were developed.展开更多
In this paper, a new current-controlled-power technique for small signal applications is presented. The proposed technique needs no passive devices (a resistor and a capacitor) but the well-known SCR technique needs, ...In this paper, a new current-controlled-power technique for small signal applications is presented. The proposed technique needs no passive devices (a resistor and a capacitor) but the well-known SCR technique needs, thus the proposed technique is very suitable for an IC process. An example application as a new current-controlled-power CMOS fullwave rectifier is also given. The example application is simulated by using the SPICE program. Simulation results show that the proposed technique can work well;the controlled-current from 0 μA to 5.5 μA produces the peak area amplitude from 100 mV to 0 mV to the load.展开更多
基金supported by State Grid Science and Technology Project“Study on Key Technologies of Large Scale Offshore Wind Power Integrating with Onshore Grid”(4000-202055045A-0-0-00)
文摘Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the application of conventional control strategies for stability operation face several challenges due to the uncontrollability of the DR.In this paper,a coordinated control strategy of offshore wind farms using the DR-HVDC transmission technology to connect with the onshore grid,is investigated.A novel coordinated control strategy for DR-HVDC is proposed based on the analysis of the DC current control ability of the full-bridge-based modular multilevel converter(FB-MMC)at the onshore station and the input and output characteristics of the diode rectifier at the offshore.Considering the characteristics of operation stability and decoupling between reactive power and active power,a simplified design based on double-loop droop control for offshore AC voltage is proposed after power flow and voltage–current(I–V)characteristics of the offshore wind farm being analyzed.Furthermore,the impact of onshore AC fault to offshore wind farm is analyzed,and a fast fault detection and protection strategy without relying on communication is proposed.Case studies carried out by PSCAD/EMTDC verify the effectiveness of the proposed control strategy for the start up,power fluctuation,and onshore and offshore fault conditions.
基金supported in part by the National Natural Science Foundation of China (Nos. 51777093 ,51722702)
文摘The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence components,the proposed nonlinear control strategy suppresses the twice frequency ripple and guarantees the dynamic response characteristic at the same time.Thanks to the proposed nonlinear control strategy,the DC bus capacitor can be reduced a lot since the voltage ripple and drop can be suppressed.A 10 kW Vienna rectifier is built to verify the proposed control strategy.After applying the proposed nonlinear control strategy,the voltage ripple is only7 V and decreases over 75%over the traditional PI control when the unbalanced degree is 20%.The voltage drop can be reduced about 80%than former control strategy which is helpful to reduce the DC bus capacitor and achieve higher power density.The volume of the capacitor can be reduced by 83.3%with the new control method.
基金Project supported by the Beijing Municipal Natural Science Foundation,China(Grant No.4162030)the National Science and Technology Major Project of China(Grant No.2013ZX02303002)
文摘The comprehensive understanding of the structure-dependent electrostatic discharge behaviors in a conventional diode-triggered silicon controlled rectifier （DTSCR） is presented in this paper. Combined with the device simulation, a mathematical model is built to get a more in-depth insight into this phenomenon. The theoretical studies are verified by the transmission-line-pulsing （TLP） test results of the modified DTSCR structure, which is realized in a 65-nm complementary metal-oxide-semiconductor （CMOS） process. The detailed analysis of the physical mechanism is used to provide predictions as the DTSCR-based protection scheme is required. In addition, a method is also presented to achieve the tradeoff between the leakage and trigger voltage in DTSCR.
文摘In this paper, a voltage oriented control strategy for three-level PWM rectifier based on Sliding Mode Control (SMC) is introduced in order to obtain fast and accurate response of dc-bus voltage. To verify the validity of the analysis and the feasibility of the proposed control method a set of simulation tests have been conducted using Matlab/Simulink. The simulation results show that compared to the conventional PI controller, the SMC can reduce drastically the three-level rectifier’s voltage fluctuation and improve the dynamic response of dc-bus significantly.
文摘To solve the problem of harmonic pollution to the power grid that caused by traditional diode rectifier and phase controlled rectifier, the unit power factor PWM rectifier is designed. The topology structure of the rectifier circuit is introduced and the double closed-loop control strategy in three-phase stationary coordinate system is analyzed. For the deficiency of control strategy, the control strategy in two-phase synchronous rotating coordinate system is proposed. This makes the independent control of active current and reactive current to be realized. The simulation model of the PWM rectifier is built and the effectiveness of the control method proposed in this paper is verified by simulation.
基金funded by the Xi’an Science and Technology Plan Project,Grant No.2020KJRC001the Xi’an Science and Technology Plan Project,Grant No.21XJZZ0003。
文摘Due to attractive features,including high efficiency,low device stress,and ability to boost voltage,a Vienna rectifier is commonly employed as a battery charger in an electric vehicle(EV).However,the 6k±1 harmonics in the acside current of the Vienna rectifier deteriorate theTHDof the ac current,thus lowering the power factor.Therefore,the current closed-loop for suppressing 6k±1 harmonics is essential tomeet the desired total harmonic distortion(THD).Fast repetitive control(FRC)is generally adopted;however,the deviation of power grid frequency causes delay link in the six frequency fast repetitive control to become non-integer and the tracking performance to deteriorate.This paper presents the detailed parameter design and calculation of fractional order fast repetitive controller(FOFRC)for the non-integer delay link.The finite polynomial approximates the non-integer delay link through the Lagrange interpolation method.By comparing the frequency characteristics of traditional repetitive control,the effectiveness of the FOFRC strategy is verified.Finally,simulation and experiment validate the steadystate performance and harmonics suppression ability of FOFRC.
基金Project partially supported by the Zhejiang Provincial Nature Science Fund of China (Nos. Y107055 and Y1080546)the Semiconductor Manufacturing International Corp. (SMIC)
文摘A diode-triggered silicon controlled rectifier (DTSCR) is being developed as an electrostatic discharge (ESD) pro- tection device for low voltage applications. However, DTSCR leaks high current during normal operation due to the Darlington effect of the triggering-assist diode string. In this study, two types of diode string triggered SCRs are designed for low leakage consideration; the modified diode string and composite polysilicon diode string triggered SCRs (MDTSCR & PDTSCR). Com- pared with the conventional DTSCR (CDTSCR), the MDTSCR has a much lower substrate leakage current with a relatively large silicon cost, and the PDTSCR has a much lower substrate leakage current with similar area and shows good leakage performance at a high temperature. Other DTSCR ESD properties are also investigated, especially regarding their layout, triggering voltage and failure current.
基金National Natural Science Foundation of China(Nos.51767013,52067013)。
文摘In predictive direct power control(PDPC)system of three-phase pulse width modulation(PWM)rectifier,grid voltage sensor makes the whole system more complex and costly.Therefore,third-order generalized integrator(TOGI)is used to generate orthogonal signals with the same frequency to estimate the grid voltage.In addition,in view of the deviation between actual and reference power in the three-phase PWM rectifier traditional PDPC strategy,a power correction link is designed to correct the power reference value.The grid voltage sensor free algorithm based on TOGI and the corrected PDPC strategy are applied to three-phase PWM rectifier and simulated on the simulation platform.Simulation results show that the proposed method can effectively eliminate the power tracking deviation and the grid voltage.The effectiveness of the proposed method is verified by comparing the simulation results.
文摘Aiming at the PWM rectifier control strategy of sliding mode control, steady state performance weak Hamiltonian control dynamic tracking performance is poor, the coordinated compound control is proposed, the feedback linearization controller and sliding mode controller Hamiltonian system is obtained, and the design of a coordinated control strategy. In order to verify the accuracy of this method, MATLAB/Simulink is used for simulation analysis. The simulation results show that the composite control can achieve the coordinated dynamic rapid tracking and constant DC output and unit power factor operation, and satisfy the control requirements of the rectifier, effectively reducing the disturbance effect on the system. Compared with Hamiltonian control, the proposed method combines the advantages of the two methods, which have the fast tracking performance and excellent steady-state characteristics, and the research prospect is broad.
文摘This paper presents a PFCVF (Power Factor Correction) rectifier that uses a variable frequency source for alternators for electric and hybrid vehicles application. In such application, the frequency of the signal in the alternator changes according to the vehicle speed, more over the loading effect on the alternator introduces harmonic currents and increases the alternator apparent power requirements. To overcome these problems and aiming more stability and better design of the alternator, a new third harmonic injection technique is proposed. This technique allows to preserve a good THD (Total Harmonic Distortion) of the input source at any frequency and to decrease losses in semiconductors switches, thereby allowing more stability and reducing the apparent power requirements. A comparative study between the standard and the new technique is made and highlights the effectiveness of the new design. A detailed analysis of the proposed topology is presented and simulations as well as experimental results are shown.
基金supported by National Natural Science Foundation of China(No.61903291)Shaanxi Province Key R&D Program(No.2022GY-134)。
文摘A control strategy of repetitive control without inductorance decoupling was proposed to address the problem of high total harmonic distortion(THD)rate of the network-side current caused by the reduced stability of the rectifier module of the DC charging pile under weak grid as well as the dead zone and nonlinearity of switching devices during charging.Firstly,the parallel repetitive control was constructed in the inner current loop,and the proportional-integral(PI)+repetitive controller based on parallel structure was designed.For system compensation,a second-order low-pass filter was selected to correct the system,and the network-side current harmonics were actively suppressed without increasing the filtering device,which effectively improves the quality of grid-connected current.Secondly,based on the synthetic vector method,the controller parameters were designed to realize the elimination of main pole by establishing two synchronous rotation coordinate system vector differential equations,so as to realize the inductanceless decoupling to cope with the influence of network-side inductance fluctuation on the stability of the control system under weak grid.By theoretical analysis and simulation,the proposed control strategy was embedded into the self-developed digital signal processor for the rectifier module of DC charging pile,simulated dynamic and steady-state operation experiments were conducted,and comparative analysis was performed to prove the feasibility of the proposed control strategy.
基金supported in part by the National Natural Science Foundation of China(No.61963030)the Education Administration project(No.17YJA630085)the Education Reform Project(No.202137)。
文摘Power factor correction (PFC) is widely used in many industry fields. In this paper, a novel multiplexed and paralleled PFC rectifier (MPPR) is proposed. Compared with the paralleled traditional six-switch buck-type PFC rectifier (SSBPR), the proposed one uses fewer switches by multiplexing. And it is beneficial for system hardware design. The commutation states of the rectifier are illustrated in detail. By comparing the active power switches, it is shown that the efficiency of the rectifier is similar to that of the traditional paralleled one. Because the commutation states for the upper and lower parts of the rectifier are different, the controller of the converter is analyzed step by step. The forward duties and the inductor current references are discussed by considering the different input voltages of the upper and lower parts of the MPPR. Then the controller is presented and analyzed. Finally the effectiveness of the MPPR is verified by experiments.
文摘In this paper, the modified LCC type of series-parallel Resonant Converter (RC) was designed and state-space modeling analysis was implemented. In this proposed converter, one leg of full bridge diode rectifier is replaced with Synchronous Rectifier (SR) switches. The proposed LCC converter is controlled using frequency modulation in the nominal state. During hold-up time, the SRswitches control is changed from in-phase to phase-shifted gate signal to obtain high DC voltage conversion ratio. Furthermore, the closed loop PI and fuzzy provide control on the output side without decreasing the switching frequency. The parameter such as conduction loss on primary and secondary side, switching loss, core and copper also reduced. Simultaneously, the efficiency is increased about 94.79 is realized by this scheme. The proposed converter with an input of 40 V is built to produce an output of 235 V with the help of ZVS boost converter [1] even under line and load disturbances. As a comparison, the closed loop fuzzy controller performance is feasible and less sensitive than PI controller.
文摘The performance of the current stabilization control system in an aluminum smelter affects the quality and the quantity of the electrolytic products. This paper elaborates the power supply, in which the diode rectifiers and the self-saturable reactors could keep the series current stable, then describes the basic principle of the rectifier unit control and the series current control. A coordinate strategy is proposed to keep the series current stable, the self-saturable reactors are controlled by a proportional-integral control scheme and the on load tap changers of transformer are triggered by the errors between the setting value of the series voltage and the measured values of the series voltage. Simulation results on PSCAD/EMTDC show that the effectiveness of the proposed strategy to keep the series current stable.
文摘This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-phase half-controlled rectifier has been designed to control and convert the AC power into DC power.In addition,two types of direct current converters have been used in this paper which are a buck and bidirectional DC/DC converters.These systems adjust the output voltage to be lower or higher than the input voltage.In the buck converters,the main switch operates in conduction or cut-off mode and is triggered by a Pulse-Width Modulated(PWM)signal.The output and input voltage levels ratio are used to calculate thePWMsignal’s duty cycle.Therefore,the duty cycle indicates the operation mode of the converter in steady-state operation.In this study,we analyze and control of a buck converter with the PWM signal.Besides,the bidirectional DC/DC converter has been achieved and optimized by PI control methods to control the battery charging and discharging modes.The simulation has been applied via the Matlab/Simulink environment.The results show the activity of each part of the designed circuits starting from the converters and the battery control system in charge and discharge modes.
文摘MPI（multishot pellet injector） was imported from Russia about ten years ago. During the year＇s operation in HL-1M, most electrical equipments were repaired. Since the components are non-standard, so it is difficult to maintain. To fueling experiment meet the requirement of in HL-2A. The power supplies of fast valve and a programmable controller for shooting pellets were developed.
文摘In this paper, a new current-controlled-power technique for small signal applications is presented. The proposed technique needs no passive devices (a resistor and a capacitor) but the well-known SCR technique needs, thus the proposed technique is very suitable for an IC process. An example application as a new current-controlled-power CMOS fullwave rectifier is also given. The example application is simulated by using the SPICE program. Simulation results show that the proposed technique can work well;the controlled-current from 0 μA to 5.5 μA produces the peak area amplitude from 100 mV to 0 mV to the load.
