In this study, powder metallurgy methods were used to fabricate Mg-7.5Li-3Al-Zn alloys from repowdered extruded alloys. Extruded alloys were powdered using ultrasonic atomization, and then laser powder bed fusion(LPBF...In this study, powder metallurgy methods were used to fabricate Mg-7.5Li-3Al-Zn alloys from repowdered extruded alloys. Extruded alloys were powdered using ultrasonic atomization, and then laser powder bed fusion(LPBF) and pulse plasma sintering(PPS) were used to consolidate the bulk materials. A comparison of the properties of the fabricated alloys with those of a conventionally extruded one was carried out using methods that characterized the microstructure and corrosion resistance. When compared to their conventionally extruded counterpart, LPBF and PPS materials exhibited refined microstructures with low enrichment in Al Li and coarse Al, Zn, Mn precipitates. The main drawback of the LPBF alloy, printed for the needs of this study, was its porosity, which had a negative effect on its corrosion. The presence of unrecrystallized particle boundaries in the PPS alloy was also unbeneficial with regard to corrosion. The advantage of the LPBF and PPS processes was the ability to change the proportion of α(Mg) to β(Li), which when the complete consolidation of the material is achievable, may increase the corrosion resistance of dual-structured Mg-Li alloys. The results show that powder metallurgy routes have a wide potential to be used for the manufacture of Mg-Li based alloys.展开更多
In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past...In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past.Reported here are measurements of the voltage distribution between the plates of a parallel-plate pulsed plasma thruster under different discharge voltages,based on which the variations in the total circuit inductance and resistance as well as those between the plates are calculated.The results show that the time-averaged voltage across the plates accounts for 28.7%-50.4%of the capacitor voltage.As the capacitor initial voltage increases from 1250 V to 2000 V,the voltage across the plates rises,but its proportion relative to the capacitor voltage decreases.For every 250 V increase in the capacitor initial voltage,the average voltage proportion across the plates decreases by approximately 2%-3%.Additionally,the voltage proportion decreases gradually from the end near the propellant outward.The voltage distribution ratio between the plates is correlated with the proportions of the resistance and inductance between the plates relative to the total circuit.展开更多
A numerical simulation method is employed to investigate the effects of the unsteady plasma body force over the stalled NACA 0015 airfoil at low Reynolds number flow conditions. The plasma body force created by a diel...A numerical simulation method is employed to investigate the effects of the unsteady plasma body force over the stalled NACA 0015 airfoil at low Reynolds number flow conditions. The plasma body force created by a dielectric barrier discharge actuator is modeled with a phenomenological method for plasma simulation coupled with the compressible Navier-Stokes equations. The governing equations are solved using an efficient implicit finitevolume method. The responses of the separated flow field to the effects of an unsteady body force in various inter- pulses and duty cycles as well as different locations and magnitudes are studied. It is shown that the duty cycle and inter-pulse are key parameters for flow separation control. Additionally, it is concluded that the body force is able to attach the flow and can affect boundary layer grow that Mach number 0.1 and Reynolds number of 45000.展开更多
Carbyne-enriched nanomaterials are of current interest in nanotechnology-related applications.The properties of these nanomaterials greatly depend on their production process.In particular,structural self-organization...Carbyne-enriched nanomaterials are of current interest in nanotechnology-related applications.The properties of these nanomaterials greatly depend on their production process.In particular,structural self-organization and auto-synchronization of nanostructures are typical phenomena observed during the growth and heteroatom-doping of carbyne-enriched nanostructured metamaterials by the ion-assisted pulse-plasma deposition method.Accordingly,fine tuning of these processes may be seen as the key step to the predictive designing of carbyneenriched nano-matrices with improved properties.In particular,we propose an innovative concept,connected with application of the vibrational-acoustic effects and based on universal Cymatics mechanisms.These effects are used to induce vibration-assisted self-organized wave patterns together with the simultaneous manipulation of their properties through an electric field.Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions serves as the additional energizing factor controlling the local pattern formation and self-organization of the nano-structures.展开更多
Plasma flow control technology has broad prospects for application.Compared with conventional dielectric barrier discharge plasma actuators(DBD-PA),the sliding discharge plasma actuator(SD-PA)has the advantages of a l...Plasma flow control technology has broad prospects for application.Compared with conventional dielectric barrier discharge plasma actuators(DBD-PA),the sliding discharge plasma actuator(SD-PA)has the advantages of a large discharge area and a deflectable induced jet.To achieve the basic performance requirements of light weight,low cost,and high reliability required for UAV(Unmanned Aerial Vehicle)plasma flight experiments,this work designed a microsecond pulse plasma supply that can be used for sliding discharge plasma actuators.In this study,the topology of the primary circuit of the microsecond pulse supply is determined,the waveform of the output terminal of the microsecond pulse plasma supply is detected using the Simulink simulation platform,and the design of the actuation voltage,the pulse frequency modulation function and the construction of the hardware circuit are achieved.Using electrical diagnosis and flow field analysis,the actuation characteristics and flow characteristics of sliding discharge plasma under microsecond pulse actuation are studied,the optimal electrical actuation parameters and flow field characteristics are described.展开更多
Pulsed plasma arc deposition （PPAD）, which combines pulsed plasma cladding with rapid prototyping, is a promising technology for manufacturing near net shape components due to its superiority in cost and convenience...Pulsed plasma arc deposition （PPAD）, which combines pulsed plasma cladding with rapid prototyping, is a promising technology for manufacturing near net shape components due to its superiority in cost and convenience of processing. In the present research, PPAD was successfully used to fabricate the Ni-based superalloy Inconel 625 components. The microstructures and mechanical properties of deposits were investigated by scanning electron microscopy （SEM）, optical microscopy （OM）, transmission electron microscopy （TEM） with energy dispersive spectrometer （EDS）, microhardness and tensile testers. It was found that the as-deposited structure exhibited homogenous columnar dendrite structure, which grew epitaxially along the deposition direction. Moreover, some intermetallic phases such as Laves phase, minor MC （NbC, TiC） carbides and needle-like δ-Ni3Nb were observed in y-Ni matrix. Precipitation mechanism and distribution characteristics of these intermetallic phases in the as-deposited 625 alloy sample were analyzed. In order to evaluate the mechanical properties of the deposits, microhardness was measured at various location （including transverse plane and longitudinal plane）. The results revealed hardness was in the range of 260- 285 HVo.2. In particular, microhardness at the interface region between two adjacent deposited layers was slightly higher than that at other regions due to highly refined structure and the disperse distribution of Laves particles. Finally, the influence of precipitation phases and fabrication strategies on the tensile properties of the as-deposited samples was investigated. The failure modes of the tensile specimens were analyzed with fractography.展开更多
Technological miniaturization has enabled the development of small satellites weighing as little as 1 kg.Unfortunately,there is still a lack of suitable efficient micropropulsion systems at these scales.The pulsed pla...Technological miniaturization has enabled the development of small satellites weighing as little as 1 kg.Unfortunately,there is still a lack of suitable efficient micropropulsion systems at these scales.The pulsed plasma thruster is a structurally simple form of electric propulsion.This simplicity also makes it ideally suited for miniaturization.Its history can be traced back to applications in satellites that are much larger than micro/nano-satellites.The vast majority of modern pulsed plasma thrusters use solid polytetrafluoroethylene(PTFE)as a propellant.Unfortunately,at lower discharge energy levels such as those necessitated by the power limitations of micro/nano-satellites,PTFE has a tendency to exhibit carbon deposition,which can ultimately lead to thruster failure.In this new era of small satellites,it is important to consider alternative propellants in the miniaturization of pulsed plasma thrusters.This brief review discusses the needs and limitations of small satellites and alternative propellants that may be able to meet these needs.Such propellants may be able to offer advantages such as a longer thruster lifetime,a higher specific impulse,or a higher thrust-topower ratio.This would enable the development of different types of pulsed plasma thrusters that can be tailored towards specific mission requirements.展开更多
The application and development of pulsed plasma thrusters(PPTs)in recent years are reviewed in this paper.The advantages of PPTs are discussed.The schematics,propulsion performance parameters and key physical process...The application and development of pulsed plasma thrusters(PPTs)in recent years are reviewed in this paper.The advantages of PPTs are discussed.The schematics,propulsion performance parameters and key physical processes of PPTs are described.Some representative PPT products and flight systems developed in recent years are presented to show the performance of the PPT.Studies about how electrode structures,discharge circuits,propellant materials,energy discharge method,propellant feed method,ignition method and number of thruster heads influence the PPT performance are presented and analyzed.The ignitor design method,ignition process and propellant carbonization are introduced to discuss the reliability and lifetime issues in PPTs.The modeling methods of the discharge circuit,as well as ablation,ionization and acceleration in PPTs are presented.Finally,the application of PPTs in the future is analyzed and some suggestions for PPT development are proposed.展开更多
This study aims to draw an exact boundary for microstructural and mechanical behaviors in terms of pulsed plasma nitriding conditions.The pulsed plasma nitriding treatment was applied to AISI 304 austenitic stainless ...This study aims to draw an exact boundary for microstructural and mechanical behaviors in terms of pulsed plasma nitriding conditions.The pulsed plasma nitriding treatment was applied to AISI 304 austenitic stainless steel at different temperatures and durations.Results reveal that nitriding depth increased as process temperature and duration increase.The nitriding depth remarkably increased at 475℃for 8 h and at 550℃for 4 h.An austenite structure was transformed into a metastable nitrogen-oversaturated body-centered tetragonal expanded austenite(S-phase)during low-temperature plasma nitriding.The S-phase was converted to CrN precipitation at 475℃for 8 h and at 550℃for 4 h.Surface hardness and fatigue limit increased through plasma nitriding regardless of process conditions.The best surface hardness and fatigue limit were obtained at 550℃for 4 h because of the occurrence of CrN precipitation.展开更多
A hybrid gas/liquid pulsed discharge plasma reactor using a porous ceramic tube is proposed for dye wastewater treatment. High voltage pulsed discharge plasma was generated in the gas phase and simultaneously the plas...A hybrid gas/liquid pulsed discharge plasma reactor using a porous ceramic tube is proposed for dye wastewater treatment. High voltage pulsed discharge plasma was generated in the gas phase and simultaneously the plasma channel was permeated through the tiny holes of the ceramic tube into the water phase accompanied by gas bubbles. The porous ceramic tube not only separated the gas phase and liquid phase but also offered an effective plasma spreading channel. The effects of the peak pulse voltage, additive gas varieties, gas bubbling rate, solution conductivity and TiO2 addition were investigated. The results showed that this reactor was effective for dye wastewater treatment. The decoloration efficiency of Acid Orange II was enhanced with an increase in the power supplied. Under the studied conditions, 97% of Acid Orange II in aqueous solution was effectively decolored with additive oxygen gas, which was 51% higher than that with argon gas, and the increasing 02 bubbling rate also benefited the decoloration of dye wastewater. Water conductivity had a small effect on the level of decoloration. Catalysis of TiO2 could be induced by the pulsed discharge plasma and addition of TiO2 aided the decoloration of Acid Orange II.展开更多
Effectiveness of pulsed power plasma for the degradation of two toxic volatile organic compounds(VOCs),toluene and methyl isobutyl ketone(MIBK),in aqueous solution was evaluated.The plasma degradation of MIBK has been...Effectiveness of pulsed power plasma for the degradation of two toxic volatile organic compounds(VOCs),toluene and methyl isobutyl ketone(MIBK),in aqueous solution was evaluated.The plasma degradation of MIBK has been studied for the first time.The influence of initial concentration of target compound,solution pH and scavengers on percentage degradation was evaluated.100%removal of 200 mg/L of toluene and MIBK was achieved both in liquid and gaseous phases after 12 and 16 min of plasma treatment,respectively.The first order rate constant of toluene and MIBK degradation(for 200 mg/L each)was 0.421 and 0.319 min~(-1)respectively when they were treated individually,and these values decreased slightly during degradation of their mixture.MIBK degradation was slower than toluene and it might be due to semi volatile and hydrophilic nature of MIBK.The effect of initial concentration of toluene and MIBK showed different degradation patterns.Highest degradation of both the compounds was obtained in neutral pH and in absence of scavengers.·OH radical was the major reactive species involved in their degradation.Their degradation in real environmental matrices showed that removal reduced significantly in secondary effluent due to scavenging of reactive species by various ions and organic matter.The total number of degradation intermediates identified in case of toluene and MIBK was 11 and 14 respectively and formate was the one recalcitrant byproduct generated.The degradation pathway of toluene and MIBK involving reactions of reactive oxygen and nitrogen species and reductive species is proposed.展开更多
In this paper, the conversion of CO2/CH4 by using pulse corona plasma was studied at atmospheric pressure and ambient temperature. The effects of ratio of CO2/CH4, pulse voltage and repeated frequency of plasma discha...In this paper, the conversion of CO2/CH4 by using pulse corona plasma was studied at atmospheric pressure and ambient temperature. The effects of ratio of CO2/CH4, pulse voltage and repeated frequency of plasma discharge were first studied in the system.展开更多
Pulsed discharge plasma has exhibited active potential to prepare low molecular weight chitosan. In the present study, the viscosity of ehitosan solution was decreased noticeably after treated with pulsed corona disch...Pulsed discharge plasma has exhibited active potential to prepare low molecular weight chitosan. In the present study, the viscosity of ehitosan solution was decreased noticeably after treated with pulsed corona discharge plasma. An experimental investigation on electrical characteristics of pulsed corona discharge plasma in chitosan solution was conducted with a view toward getting insight into discharge process. Factors affecting I-V curve, single pulse injec- tion energy and pulse width were studied. Experimental results showed positive effect of pulsed peak voltage on discharge plasma in chitosan solution. Pulse-forming capacitor greatly influenced the discharge form, and 4 nF was observed as a suitable value for efficiently generating stable discharge plasmas. As the electrode distance was larger than 10 ram, it had slight impact on dis- charge plasma due to the excellent conductive-property of chitosan solution. The injection energy significantly increased with air flow rate, while the pulse width hardly changed as the air flow rate increased from 0.5 m^3/h to 1.0 m^3/h. This study is expected to provide reference for promoting the application of pulsed corona discharge plasma to ehitosan solution treatment.展开更多
In the present study,a combination of pulsed discharge plasma and TiO2（plasma/TiO2）has been developed in order to study the activity of TiO2by varying the discharge conditions of pulsed voltage,discharge mode,air fl...In the present study,a combination of pulsed discharge plasma and TiO2（plasma/TiO2）has been developed in order to study the activity of TiO2by varying the discharge conditions of pulsed voltage,discharge mode,air flow rate and solution conductivity.Phenol was used as the chemical probe to characterize the activity of TiO2in a pulsed discharge system.The experimental results showed that the phenol removal efficiency could be improved by about 10%by increasing the applied voltage.The phenol removal efficiency for three discharge modes in the plasma-discharge-alone system was found to be highest in the spark mode,followed by the spark–streamer mode and finally the streamer mode.In the plasma/TiO2system,the highest catalytic effect of TiO2was observed in the spark–streamer discharge mode,which may be attributed to the favorable chemical and physical effects from the spark–streamer discharge mode,such as ultraviolet light,O3,H2O2,pyrolysis,shockwaves and high-energy electrons.Meanwhile,the optimal flow rate and conductivity were 0.05 m^3l^（-1）and 10μS cm^（-1）,respectively.The main phenolic intermediates were hydroquinone,catechol,and p-benzoquinone during the discharge treatment process.A different phenol degradation pathway was observed in the plasma/TiO2system as compared to plasma alone.Analysis of the reaction intermediates demonstrated that p-benzoquinone reduction was selectively catalyzed on the TiO2surface.The effective decomposition of phenol constant（De）increased from 74.11%to 79.16%when TiO2was added,indicating that higher phenol mineralization was achieved in the plasma/TiO2system.展开更多
The triple Langmuir probe enables measurements of the transient plasma parameters over time at a point of interest.We demonstrate how these measurements can be easily combined to obtain a visualization of the overall ...The triple Langmuir probe enables measurements of the transient plasma parameters over time at a point of interest.We demonstrate how these measurements can be easily combined to obtain a visualization of the overall plasma behavior of a pulsed plasma thruster.Through this,it is possible to identify features in the expansion of the plasma such as the canting angle of the plume.We also identified the early arrival of a negatively canted low-density plasma plume.The 2D profiles also reveal data that would otherwise be obscured by other planes in optical measurements.展开更多
Pulsed plasma thrusters(PPTs)are an attractive form of micro-thrusters due to advantages such as their compactness and lightweight design compared to other electric propulsion systems.Experimental investigations on th...Pulsed plasma thrusters(PPTs)are an attractive form of micro-thrusters due to advantages such as their compactness and lightweight design compared to other electric propulsion systems.Experimental investigations on their plasma properties are beneficial in clarifying the complex process of plasma evolution during the micro-second pulse discharge of a PPT.In this work,the multi-dimensional evolutions of the light intensity of the PPT plasma with wavelength,time,and position were identified.The plasma pressure was obtained using an iterative process with composition calculations.The results show that significant ion recombination occurred in the discharge channel since the line intensities of CII,CIII,CIV,and FII decreased and those of CI and FI increased as the plasma moved downstream.At the center of the discharge channel,the electron temperature and electron density were in the order of 10000 K and 1017 cm-3,respectively.These had maximum values of 13750 K and 2.3?×?1017 cm-3 and the maximum temperature occurred during the first half-cycle while the maximum number density was measured during the second half-cycle.The estimated plasma pressure was in the order of 105 Pa and exhibited a maximum value of 2.69?×?105 Pa.展开更多
The effects of three different typical resistivity models（Spitzer, Z＆L and M＆G） on the performance of pulsed inductive acceleration plasma are studied. Numerical results show that their influences decrease with th...The effects of three different typical resistivity models（Spitzer, Z＆L and M＆G） on the performance of pulsed inductive acceleration plasma are studied. Numerical results show that their influences decrease with the increase of the plasma temperature. The significant discriminations among them appear at the plasma temperature lower than 2.5 eV, and the maximum gap of the pulsed inductive plasma accelerated efficiency is approximately 2.5%.Moreover, the pulsed inductive plasma accelerated efficiency is absolutely related to the dynamic impedance parameters, such as voltage, inductance, capacitance and flow rate. However, the distribution of the efficiency as a function of plasma temperature with three resistivity models has nothing to do with the dynamic impedance parameter.展开更多
In this study,a laser-assisted pulsed plasma thruster(LA-PPT)with a novel configuration is proposed as an electric propulsion thruster which separates laser ablation and electromagnetic acceleration.Owing to the uniqu...In this study,a laser-assisted pulsed plasma thruster(LA-PPT)with a novel configuration is proposed as an electric propulsion thruster which separates laser ablation and electromagnetic acceleration.Owing to the unique structure of the thruster,metals can also be used as propellants,and a higher specific impulse is expected.The ablation quality,morphology,and plume distribution of various metals(aluminium alloy,red copper,and carbon steel)with different laser energies were studied experimentally.The ablation morphology and plume distribution of red copper were more uniform,as compared to those of other metals,and the ablation quality was higher,indicating its greater suitability for LA-PPT.The plume generated by nanosecond laser ablation of aluminium alloy expanded faster,which indicated that the response time of the thruster with aluminium alloy as the propellant was shorter.In addition,when the background pressure was 0.005 Pa,an obvious plume splitting phenomenon was observed in the ablation plume of the pulsed laser irradiating aluminium alloy,which may significantly reduce the utilisation rate of the propellant.展开更多
In this paper, a pulsed discharge plasma （PDP） system with a multi-needle-to-plate electrodes geometry was set up to investigate the regeneration of acid orange 7 （AO7） exhausted granular activated carbon （GAC）....In this paper, a pulsed discharge plasma （PDP） system with a multi-needle-to-plate electrodes geometry was set up to investigate the regeneration of acid orange 7 （AO7） exhausted granular activated carbon （GAC）. Regeneration of GAC was studied under different conditions of peak pulse discharge voltage and water pH, as well as the modification effect of GAC by the pulse discharge process, to figure out the regeneration efficiency and the change of the GAC structure by the PDP treatment. The obtained results showed that there was an appropriate peak pulse voltage and an optimal initial pH value of the solution for GAC regeneration. Analyses of scanning electron microscope （SEM）, Boehm titration, Brunauer-Emmett-Teller （BET）, Horvath-Kawazoe （HK）, and X-ray Diffraction （XRD） showed that there were more mesopore and macropore in the regenerated GAC and the structure turned smoother with the increase of discharge voltage; the amount of acidic functional groups on the GAC surface increased while the amount of basic functional groups decreased after the regeneration process. From the result of the XRD analysis, there were no new substances produced on the GAC after PDP treatment.展开更多
A novel laser-assisted pulsed plasma thruster(LA-PPT)is proposed as an electric propulsion thruster,which separates laser ablation and electromagnetic acceleration.It aims for a higher specific impulse than that achie...A novel laser-assisted pulsed plasma thruster(LA-PPT)is proposed as an electric propulsion thruster,which separates laser ablation and electromagnetic acceleration.It aims for a higher specific impulse than that achieved with conventional LA-PPTs.Owing to the short-time discharge and the novel configuration,the physical mechanism of the discharge is unclear.Time and spatial-resolved optical emission spectroscopy was applied to investigate the variation in the plasma properties in the thruster discharge channel.The plasma species,electron temperature,and electron density were obtained and discussed.Our investigation revealed that there were H_(α),H_(β),H_(γ),H_(ε) atoms,CⅠ,CⅡ,CⅢ,CⅣ,ClⅠ,ClⅡparticles,and a small amount of CH,C_(3),C_(2),H_(2) neutral molecular groups in the plasma.The electron temperature of the discharge channel of the thruster was within 0.6–4.9 e V,and the electron density was within(1.1–3.0)×10^(18)cm^(-3),which shows that the optical emission spectroscopy method is to measure the electron excitation temperature and electron density in heavy particles.But the Langmuir probe method is to measure the temperature and density of free electrons.The use of laser instead of spark plug as the ignition mode significantly changed the plasma distribution in the discharge channel.Unlike the conventional PPT,which has high electron density near the thruster surface,LAPPT showed relatively large electron density at the thruster outlet,which increased the thruster specific impulse.In addition,the change in the ignition mode enabled the electron density in the LA-PPT discharge channel to be higher than that in the conventional PPT.This proves that the ignition mode with laser replacing the spark plug effectively optimised the PPT performance.展开更多
文摘In this study, powder metallurgy methods were used to fabricate Mg-7.5Li-3Al-Zn alloys from repowdered extruded alloys. Extruded alloys were powdered using ultrasonic atomization, and then laser powder bed fusion(LPBF) and pulse plasma sintering(PPS) were used to consolidate the bulk materials. A comparison of the properties of the fabricated alloys with those of a conventionally extruded one was carried out using methods that characterized the microstructure and corrosion resistance. When compared to their conventionally extruded counterpart, LPBF and PPS materials exhibited refined microstructures with low enrichment in Al Li and coarse Al, Zn, Mn precipitates. The main drawback of the LPBF alloy, printed for the needs of this study, was its porosity, which had a negative effect on its corrosion. The presence of unrecrystallized particle boundaries in the PPS alloy was also unbeneficial with regard to corrosion. The advantage of the LPBF and PPS processes was the ability to change the proportion of α(Mg) to β(Li), which when the complete consolidation of the material is achievable, may increase the corrosion resistance of dual-structured Mg-Li alloys. The results show that powder metallurgy routes have a wide potential to be used for the manufacture of Mg-Li based alloys.
基金supported by the Beijing Natural Science Foundation(No.QY24166).
文摘In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past.Reported here are measurements of the voltage distribution between the plates of a parallel-plate pulsed plasma thruster under different discharge voltages,based on which the variations in the total circuit inductance and resistance as well as those between the plates are calculated.The results show that the time-averaged voltage across the plates accounts for 28.7%-50.4%of the capacitor voltage.As the capacitor initial voltage increases from 1250 V to 2000 V,the voltage across the plates rises,but its proportion relative to the capacitor voltage decreases.For every 250 V increase in the capacitor initial voltage,the average voltage proportion across the plates decreases by approximately 2%-3%.Additionally,the voltage proportion decreases gradually from the end near the propellant outward.The voltage distribution ratio between the plates is correlated with the proportions of the resistance and inductance between the plates relative to the total circuit.
文摘A numerical simulation method is employed to investigate the effects of the unsteady plasma body force over the stalled NACA 0015 airfoil at low Reynolds number flow conditions. The plasma body force created by a dielectric barrier discharge actuator is modeled with a phenomenological method for plasma simulation coupled with the compressible Navier-Stokes equations. The governing equations are solved using an efficient implicit finitevolume method. The responses of the separated flow field to the effects of an unsteady body force in various inter- pulses and duty cycles as well as different locations and magnitudes are studied. It is shown that the duty cycle and inter-pulse are key parameters for flow separation control. Additionally, it is concluded that the body force is able to attach the flow and can affect boundary layer grow that Mach number 0.1 and Reynolds number of 45000.
基金This research work is jointly supported and funded by the Scientific and Technological Research Council of Turkey(TÜBİTAK)the Russian Foundation for Basic Research(RFBR)according to the Research Project No.20-58-46014.
文摘Carbyne-enriched nanomaterials are of current interest in nanotechnology-related applications.The properties of these nanomaterials greatly depend on their production process.In particular,structural self-organization and auto-synchronization of nanostructures are typical phenomena observed during the growth and heteroatom-doping of carbyne-enriched nanostructured metamaterials by the ion-assisted pulse-plasma deposition method.Accordingly,fine tuning of these processes may be seen as the key step to the predictive designing of carbyneenriched nano-matrices with improved properties.In particular,we propose an innovative concept,connected with application of the vibrational-acoustic effects and based on universal Cymatics mechanisms.These effects are used to induce vibration-assisted self-organized wave patterns together with the simultaneous manipulation of their properties through an electric field.Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions serves as the additional energizing factor controlling the local pattern formation and self-organization of the nano-structures.
基金supported by National Natural Science Foundation of China(No.61971345)the Foundation for Key Laboratories of National Defense Science and Technology of China(No.614220120030810)Shaanxi Provincial Key R&D Program General Project(No.2021GY-044)。
文摘Plasma flow control technology has broad prospects for application.Compared with conventional dielectric barrier discharge plasma actuators(DBD-PA),the sliding discharge plasma actuator(SD-PA)has the advantages of a large discharge area and a deflectable induced jet.To achieve the basic performance requirements of light weight,low cost,and high reliability required for UAV(Unmanned Aerial Vehicle)plasma flight experiments,this work designed a microsecond pulse plasma supply that can be used for sliding discharge plasma actuators.In this study,the topology of the primary circuit of the microsecond pulse supply is determined,the waveform of the output terminal of the microsecond pulse plasma supply is detected using the Simulink simulation platform,and the design of the actuation voltage,the pulse frequency modulation function and the construction of the hardware circuit are achieved.Using electrical diagnosis and flow field analysis,the actuation characteristics and flow characteristics of sliding discharge plasma under microsecond pulse actuation are studied,the optimal electrical actuation parameters and flow field characteristics are described.
基金supported by the National Basic Research Program of China("973 Project",No.2011CB013403)the National Science and Technology Supporting Project (Nos.2011BAF11B07 and 2011BAC10B05)
文摘Pulsed plasma arc deposition （PPAD）, which combines pulsed plasma cladding with rapid prototyping, is a promising technology for manufacturing near net shape components due to its superiority in cost and convenience of processing. In the present research, PPAD was successfully used to fabricate the Ni-based superalloy Inconel 625 components. The microstructures and mechanical properties of deposits were investigated by scanning electron microscopy （SEM）, optical microscopy （OM）, transmission electron microscopy （TEM） with energy dispersive spectrometer （EDS）, microhardness and tensile testers. It was found that the as-deposited structure exhibited homogenous columnar dendrite structure, which grew epitaxially along the deposition direction. Moreover, some intermetallic phases such as Laves phase, minor MC （NbC, TiC） carbides and needle-like δ-Ni3Nb were observed in y-Ni matrix. Precipitation mechanism and distribution characteristics of these intermetallic phases in the as-deposited 625 alloy sample were analyzed. In order to evaluate the mechanical properties of the deposits, microhardness was measured at various location （including transverse plane and longitudinal plane）. The results revealed hardness was in the range of 260- 285 HVo.2. In particular, microhardness at the interface region between two adjacent deposited layers was slightly higher than that at other regions due to highly refined structure and the disperse distribution of Laves particles. Finally, the influence of precipitation phases and fabrication strategies on the tensile properties of the as-deposited samples was investigated. The failure modes of the tensile specimens were analyzed with fractography.
基金supported by the National Natural Science Foundation of China(No.11802022)the Beijing Institute of Technology Research Fund Program for Young Scholars。
文摘Technological miniaturization has enabled the development of small satellites weighing as little as 1 kg.Unfortunately,there is still a lack of suitable efficient micropropulsion systems at these scales.The pulsed plasma thruster is a structurally simple form of electric propulsion.This simplicity also makes it ideally suited for miniaturization.Its history can be traced back to applications in satellites that are much larger than micro/nano-satellites.The vast majority of modern pulsed plasma thrusters use solid polytetrafluoroethylene(PTFE)as a propellant.Unfortunately,at lower discharge energy levels such as those necessitated by the power limitations of micro/nano-satellites,PTFE has a tendency to exhibit carbon deposition,which can ultimately lead to thruster failure.In this new era of small satellites,it is important to consider alternative propellants in the miniaturization of pulsed plasma thrusters.This brief review discusses the needs and limitations of small satellites and alternative propellants that may be able to meet these needs.Such propellants may be able to offer advantages such as a longer thruster lifetime,a higher specific impulse,or a higher thrust-topower ratio.This would enable the development of different types of pulsed plasma thrusters that can be tailored towards specific mission requirements.
基金supported by National Natural Science Foundation of China (No. 11672039)。
文摘The application and development of pulsed plasma thrusters(PPTs)in recent years are reviewed in this paper.The advantages of PPTs are discussed.The schematics,propulsion performance parameters and key physical processes of PPTs are described.Some representative PPT products and flight systems developed in recent years are presented to show the performance of the PPT.Studies about how electrode structures,discharge circuits,propellant materials,energy discharge method,propellant feed method,ignition method and number of thruster heads influence the PPT performance are presented and analyzed.The ignitor design method,ignition process and propellant carbonization are introduced to discuss the reliability and lifetime issues in PPTs.The modeling methods of the discharge circuit,as well as ablation,ionization and acceleration in PPTs are presented.Finally,the application of PPTs in the future is analyzed and some suggestions for PPT development are proposed.
基金the Scientific and Technological Research Council of Turkey(TUBITAK)for the support of this study(Grant No:215M134)。
文摘This study aims to draw an exact boundary for microstructural and mechanical behaviors in terms of pulsed plasma nitriding conditions.The pulsed plasma nitriding treatment was applied to AISI 304 austenitic stainless steel at different temperatures and durations.Results reveal that nitriding depth increased as process temperature and duration increase.The nitriding depth remarkably increased at 475℃for 8 h and at 550℃for 4 h.An austenite structure was transformed into a metastable nitrogen-oversaturated body-centered tetragonal expanded austenite(S-phase)during low-temperature plasma nitriding.The S-phase was converted to CrN precipitation at 475℃for 8 h and at 550℃for 4 h.Surface hardness and fatigue limit increased through plasma nitriding regardless of process conditions.The best surface hardness and fatigue limit were obtained at 550℃for 4 h because of the occurrence of CrN precipitation.
基金supported financially by the Program for Liaoning Excellent Talents in University,China (No.2009R09)National Natural Science Foundation of China (No.40901150)863 Program of China (No.2009AA064101-4)
文摘A hybrid gas/liquid pulsed discharge plasma reactor using a porous ceramic tube is proposed for dye wastewater treatment. High voltage pulsed discharge plasma was generated in the gas phase and simultaneously the plasma channel was permeated through the tiny holes of the ceramic tube into the water phase accompanied by gas bubbles. The porous ceramic tube not only separated the gas phase and liquid phase but also offered an effective plasma spreading channel. The effects of the peak pulse voltage, additive gas varieties, gas bubbling rate, solution conductivity and TiO2 addition were investigated. The results showed that this reactor was effective for dye wastewater treatment. The decoloration efficiency of Acid Orange II was enhanced with an increase in the power supplied. Under the studied conditions, 97% of Acid Orange II in aqueous solution was effectively decolored with additive oxygen gas, which was 51% higher than that with argon gas, and the increasing 02 bubbling rate also benefited the decoloration of dye wastewater. Water conductivity had a small effect on the level of decoloration. Catalysis of TiO2 could be induced by the pulsed discharge plasma and addition of TiO2 aided the decoloration of Acid Orange II.
基金the financial support received from Department of Science and Technology(DST),Government of India(Nos.DST/TM/WTI/WIC/2K17/82(G)and DST/CCP/Co E/141/2018(G))for this study。
文摘Effectiveness of pulsed power plasma for the degradation of two toxic volatile organic compounds(VOCs),toluene and methyl isobutyl ketone(MIBK),in aqueous solution was evaluated.The plasma degradation of MIBK has been studied for the first time.The influence of initial concentration of target compound,solution pH and scavengers on percentage degradation was evaluated.100%removal of 200 mg/L of toluene and MIBK was achieved both in liquid and gaseous phases after 12 and 16 min of plasma treatment,respectively.The first order rate constant of toluene and MIBK degradation(for 200 mg/L each)was 0.421 and 0.319 min~(-1)respectively when they were treated individually,and these values decreased slightly during degradation of their mixture.MIBK degradation was slower than toluene and it might be due to semi volatile and hydrophilic nature of MIBK.The effect of initial concentration of toluene and MIBK showed different degradation patterns.Highest degradation of both the compounds was obtained in neutral pH and in absence of scavengers.·OH radical was the major reactive species involved in their degradation.Their degradation in real environmental matrices showed that removal reduced significantly in secondary effluent due to scavenging of reactive species by various ions and organic matter.The total number of degradation intermediates identified in case of toluene and MIBK was 11 and 14 respectively and formate was the one recalcitrant byproduct generated.The degradation pathway of toluene and MIBK involving reactions of reactive oxygen and nitrogen species and reductive species is proposed.
文摘In this paper, the conversion of CO2/CH4 by using pulse corona plasma was studied at atmospheric pressure and ambient temperature. The effects of ratio of CO2/CH4, pulse voltage and repeated frequency of plasma discharge were first studied in the system.
基金supported by National Natural Science Foundation of China(No.40901150)
文摘Pulsed discharge plasma has exhibited active potential to prepare low molecular weight chitosan. In the present study, the viscosity of ehitosan solution was decreased noticeably after treated with pulsed corona discharge plasma. An experimental investigation on electrical characteristics of pulsed corona discharge plasma in chitosan solution was conducted with a view toward getting insight into discharge process. Factors affecting I-V curve, single pulse injec- tion energy and pulse width were studied. Experimental results showed positive effect of pulsed peak voltage on discharge plasma in chitosan solution. Pulse-forming capacitor greatly influenced the discharge form, and 4 nF was observed as a suitable value for efficiently generating stable discharge plasmas. As the electrode distance was larger than 10 ram, it had slight impact on dis- charge plasma due to the excellent conductive-property of chitosan solution. The injection energy significantly increased with air flow rate, while the pulse width hardly changed as the air flow rate increased from 0.5 m^3/h to 1.0 m^3/h. This study is expected to provide reference for promoting the application of pulsed corona discharge plasma to ehitosan solution treatment.
基金funded by the Fundamental Research Funds for the Central Universities under Grant(DUT 15QY17)National Natural Science Foundation of China(Project Nos.51477025 and U1462105)
文摘In the present study,a combination of pulsed discharge plasma and TiO2（plasma/TiO2）has been developed in order to study the activity of TiO2by varying the discharge conditions of pulsed voltage,discharge mode,air flow rate and solution conductivity.Phenol was used as the chemical probe to characterize the activity of TiO2in a pulsed discharge system.The experimental results showed that the phenol removal efficiency could be improved by about 10%by increasing the applied voltage.The phenol removal efficiency for three discharge modes in the plasma-discharge-alone system was found to be highest in the spark mode,followed by the spark–streamer mode and finally the streamer mode.In the plasma/TiO2system,the highest catalytic effect of TiO2was observed in the spark–streamer discharge mode,which may be attributed to the favorable chemical and physical effects from the spark–streamer discharge mode,such as ultraviolet light,O3,H2O2,pyrolysis,shockwaves and high-energy electrons.Meanwhile,the optimal flow rate and conductivity were 0.05 m^3l^（-1）and 10μS cm^（-1）,respectively.The main phenolic intermediates were hydroquinone,catechol,and p-benzoquinone during the discharge treatment process.A different phenol degradation pathway was observed in the plasma/TiO2system as compared to plasma alone.Analysis of the reaction intermediates demonstrated that p-benzoquinone reduction was selectively catalyzed on the TiO2surface.The effective decomposition of phenol constant（De）increased from 74.11%to 79.16%when TiO2was added,indicating that higher phenol mineralization was achieved in the plasma/TiO2system.
基金supported by National Natural Science Foundation of China(No.11802022)the Beijing Institute of Technology Research Fund Program for Young Scholars。
文摘The triple Langmuir probe enables measurements of the transient plasma parameters over time at a point of interest.We demonstrate how these measurements can be easily combined to obtain a visualization of the overall plasma behavior of a pulsed plasma thruster.Through this,it is possible to identify features in the expansion of the plasma such as the canting angle of the plume.We also identified the early arrival of a negatively canted low-density plasma plume.The 2D profiles also reveal data that would otherwise be obscured by other planes in optical measurements.
基金supported by National Natural Science Foundation of China(No.51576018)。
文摘Pulsed plasma thrusters(PPTs)are an attractive form of micro-thrusters due to advantages such as their compactness and lightweight design compared to other electric propulsion systems.Experimental investigations on their plasma properties are beneficial in clarifying the complex process of plasma evolution during the micro-second pulse discharge of a PPT.In this work,the multi-dimensional evolutions of the light intensity of the PPT plasma with wavelength,time,and position were identified.The plasma pressure was obtained using an iterative process with composition calculations.The results show that significant ion recombination occurred in the discharge channel since the line intensities of CII,CIII,CIV,and FII decreased and those of CI and FI increased as the plasma moved downstream.At the center of the discharge channel,the electron temperature and electron density were in the order of 10000 K and 1017 cm-3,respectively.These had maximum values of 13750 K and 2.3?×?1017 cm-3 and the maximum temperature occurred during the first half-cycle while the maximum number density was measured during the second half-cycle.The estimated plasma pressure was in the order of 105 Pa and exhibited a maximum value of 2.69?×?105 Pa.
基金Supported by the Fund of Science and Technology on Vacuum Technology and Physics Laboratory of Lanzhou Institute of Physics under Grant No YSC0715the National Natural Science Foundation of China under Grant No 62601210the Civil Aerospace Technology Research Project under Grant No D010509
文摘The effects of three different typical resistivity models（Spitzer, Z＆L and M＆G） on the performance of pulsed inductive acceleration plasma are studied. Numerical results show that their influences decrease with the increase of the plasma temperature. The significant discriminations among them appear at the plasma temperature lower than 2.5 eV, and the maximum gap of the pulsed inductive plasma accelerated efficiency is approximately 2.5%.Moreover, the pulsed inductive plasma accelerated efficiency is absolutely related to the dynamic impedance parameters, such as voltage, inductance, capacitance and flow rate. However, the distribution of the efficiency as a function of plasma temperature with three resistivity models has nothing to do with the dynamic impedance parameter.
基金supported by National Natural Science Foundation of China(No.11772354)。
文摘In this study,a laser-assisted pulsed plasma thruster(LA-PPT)with a novel configuration is proposed as an electric propulsion thruster which separates laser ablation and electromagnetic acceleration.Owing to the unique structure of the thruster,metals can also be used as propellants,and a higher specific impulse is expected.The ablation quality,morphology,and plume distribution of various metals(aluminium alloy,red copper,and carbon steel)with different laser energies were studied experimentally.The ablation morphology and plume distribution of red copper were more uniform,as compared to those of other metals,and the ablation quality was higher,indicating its greater suitability for LA-PPT.The plume generated by nanosecond laser ablation of aluminium alloy expanded faster,which indicated that the response time of the thruster with aluminium alloy as the propellant was shorter.In addition,when the background pressure was 0.005 Pa,an obvious plume splitting phenomenon was observed in the ablation plume of the pulsed laser irradiating aluminium alloy,which may significantly reduce the utilisation rate of the propellant.
基金supported by National Natural Science Foundation of China(No.21207052)China Postdoctoral Science Foundation(No.20110491353)Jiangsu Planned Projects for Postdoctoral Research Funds,China(No.1102116C)
文摘In this paper, a pulsed discharge plasma （PDP） system with a multi-needle-to-plate electrodes geometry was set up to investigate the regeneration of acid orange 7 （AO7） exhausted granular activated carbon （GAC）. Regeneration of GAC was studied under different conditions of peak pulse discharge voltage and water pH, as well as the modification effect of GAC by the pulse discharge process, to figure out the regeneration efficiency and the change of the GAC structure by the PDP treatment. The obtained results showed that there was an appropriate peak pulse voltage and an optimal initial pH value of the solution for GAC regeneration. Analyses of scanning electron microscope （SEM）, Boehm titration, Brunauer-Emmett-Teller （BET）, Horvath-Kawazoe （HK）, and X-ray Diffraction （XRD） showed that there were more mesopore and macropore in the regenerated GAC and the structure turned smoother with the increase of discharge voltage; the amount of acidic functional groups on the GAC surface increased while the amount of basic functional groups decreased after the regeneration process. From the result of the XRD analysis, there were no new substances produced on the GAC after PDP treatment.
基金supported by National Natural Science Foundation of China(No.11772354)。
文摘A novel laser-assisted pulsed plasma thruster(LA-PPT)is proposed as an electric propulsion thruster,which separates laser ablation and electromagnetic acceleration.It aims for a higher specific impulse than that achieved with conventional LA-PPTs.Owing to the short-time discharge and the novel configuration,the physical mechanism of the discharge is unclear.Time and spatial-resolved optical emission spectroscopy was applied to investigate the variation in the plasma properties in the thruster discharge channel.The plasma species,electron temperature,and electron density were obtained and discussed.Our investigation revealed that there were H_(α),H_(β),H_(γ),H_(ε) atoms,CⅠ,CⅡ,CⅢ,CⅣ,ClⅠ,ClⅡparticles,and a small amount of CH,C_(3),C_(2),H_(2) neutral molecular groups in the plasma.The electron temperature of the discharge channel of the thruster was within 0.6–4.9 e V,and the electron density was within(1.1–3.0)×10^(18)cm^(-3),which shows that the optical emission spectroscopy method is to measure the electron excitation temperature and electron density in heavy particles.But the Langmuir probe method is to measure the temperature and density of free electrons.The use of laser instead of spark plug as the ignition mode significantly changed the plasma distribution in the discharge channel.Unlike the conventional PPT,which has high electron density near the thruster surface,LAPPT showed relatively large electron density at the thruster outlet,which increased the thruster specific impulse.In addition,the change in the ignition mode enabled the electron density in the LA-PPT discharge channel to be higher than that in the conventional PPT.This proves that the ignition mode with laser replacing the spark plug effectively optimised the PPT performance.
