This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen w...This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.展开更多
Composite materials are increasingly used in the aerospace industry.To fully realise the weight saving potential along with superior mechanical properties that composites offer in safety critical applications,reliable...Composite materials are increasingly used in the aerospace industry.To fully realise the weight saving potential along with superior mechanical properties that composites offer in safety critical applications,reliable Non-Destructive Testing(NDT)methods are required to prevent catastrophic failures.This paper will review the state of the art in the field and point to highlight the success and challenges that different NDT methods are faced to evaluate the integrity of critical aerospace composites.The focus will be on advanced certificated NDT methods for damage detection and characterization in composite laminates for use in the aircraft primary and secondary structures.展开更多
To study ice-induced vibration of a compliant conical structure, a series of model tests were performed from 2004 to 2005. In the tests, the ice sheet before the compliant conical structure was found to fail in two-ti...To study ice-induced vibration of a compliant conical structure, a series of model tests were performed from 2004 to 2005. In the tests, the ice sheet before the compliant conical structure was found to fail in two-time breaking. From 2005 to 2006, this type of ice failure was studied through more groups of tests. The tests show that two-time breaking is the typical failure of ice before steep conical structures, and is controlled by other factors at the same time, such as ice speed and the angle of the cone.展开更多
A retrofitting technology using precast steel reinforced concrete（PSRC） panels is developed to improve the seismic performance of old masonry buildings. The PSRC panels are built up as an external PSRC wall system s...A retrofitting technology using precast steel reinforced concrete（PSRC） panels is developed to improve the seismic performance of old masonry buildings. The PSRC panels are built up as an external PSRC wall system surrounding the existing masonry building. The PSRC walls are well connected to the existing masonry building, which provides enough confinement to effectively improve the ductility, strength, and stiffenss of old masonry structures. The PSRC panels are prefabricated in a factory, significantly reducing the situ work and associated construction time. To demonstrate the feasibility and mechanical effectivenss of the proposed retrofitting system, a full-scale five-story specimen was constructed. The retrofitting process was completed within five weeks with very limited indoor operation. The specimen was then tested in the lateral direction, which could potentially suffer sigifnicant damage in a large earthquake. The technical feasibility, construction workability, and seismic performance were thoroughly demonstrated by a full-scale specimen construction and pseudo-dynamic tests.展开更多
For the study on the ice-induced vibration of a compliant mono-cone structure,a series of model tests were performed from 2004 to 2006.In these tests,the ice sheet before the compliant conical structure was found to b...For the study on the ice-induced vibration of a compliant mono-cone structure,a series of model tests were performed from 2004 to 2006.In these tests,the ice sheet before the compliant conical structure was found to be failed in two-time breaking.Based on this important finding,model tests study of the ice force on a compliant multi-cone structure were performed from 2006 to 2007.In these tests,the ice sheet broke before each single cone non-simultaneously.The exciting energy of the total ice force was found to be in a wide range of frequencies,and the structure can be easily excited with nonlinear resonance.展开更多
A pseudo-dynamic testing program was generated on a fabricated composite frame with steel plate shear walls （SPSWs） to study its seismic perlbrmance. The specimen was a three-storey single-bay frame, which was compo...A pseudo-dynamic testing program was generated on a fabricated composite frame with steel plate shear walls （SPSWs） to study its seismic perlbrmance. The specimen was a three-storey single-bay frame, which was composed of H- section steel columns and composite beams, and was assembled by bolted height-adjustable steel beam-to-column connections （BHA connections）. Beam-only-connected SPSWs were selected as lateral load resisting members. The specimen was subjected to four ground motions of progressively increasing intensity. The results showed that： （1） beam-only-connected S PSWs provided sufficient lateral load resistance, lateral stiffness, and energy dissipation capacity to the fabricated frame via the tension ficld action developed in their infill panels; （2） the fabricated frame, assembled by BHA connections, exhibited substantial redundancy and good ductility; （3） an undesirable failure mode of the fabricated frame, in huge earthquakes, included severe cracking in composite beams and block shear failure in SPSWs＇ connections; （4） the inter-storey shear force distribution determined by ASCE/SE1 7-10 was verified with experimental data.展开更多
Modem dynamic tests such as networked collaborative pseudo-dynamic testing （PDT） provide new tools to study the dynamic performance of large and complex structures. In this paper, several networked collaborative PDT...Modem dynamic tests such as networked collaborative pseudo-dynamic testing （PDT） provide new tools to study the dynamic performance of large and complex structures. In this paper, several networked collaborative PDT systems established in China and abroad are introduced, including a detailed description of the first networked collaborative platform that involved the construction of a standardized demonstration procedure for networked collaborative PDT. The example is a multi-span bridge with RC piers retrofitted by FRP, and a networked structural laboratory （NetSLab） platform is used to link distributed laboratories located at several universities together. Substructure technology is also used in the testing. The characteristics, resource sharing and collaborative work of NetSLab are described, and the results illustrate that use of the NetSLab is feasible for studying the dynamic performance of multi-span bridge structures.展开更多
With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weigh...With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weight and increase the payload,composite material structures will be widely used. It is difficult to evaluate the strength and life of composite materials due to their complex mechanism and various phenomena in damage and failure.Meanwhile,the structures of composite materials used in spacecrafts will bear complex loads,including the coupling loads of tension,pressure,bending,shear,and torsion. Static loads,thermal loads,and vibration loads may occur at the same time,which asks for verification requirements to ensure the structure safety. Therefore,it is necessary to carry out a systematic multi-level experimental study. In this paper,the building block approach (BBA) is used to investigate the multilevel composite material structures for spacecrafts. The advanced measurement technology is adopted based on digital image correlation (DIC) and piezoelectric and optical fiber sensors to measure the composite material structure deformation. The virtual experiment technology is applied to provide sufficient and reliable data for the evaluation of the composite material structures of spacecrafts.展开更多
Non-destructive testing (NDT) of structures is one of the most important tasksof the proper maintenance and diagnosis of machines and constructions structuralcondition. NDT methods contribute to the damage tolerance p...Non-destructive testing (NDT) of structures is one of the most important tasksof the proper maintenance and diagnosis of machines and constructions structuralcondition. NDT methods contribute to the damage tolerance philosophy used in theaircraft design methodology as well as many other operation and maintenance programsof machinery and constructions. The following study is focusing on overviewing animportant group of NDT methods: the optical and other ones, which found broadapplicability in scientific and industrial studies nowadays. The paper discusses theselected most widely applicable methods, namely, visual testing, ultrasonic testing,radiographic testing, infrared thermography as well as electronic speckle patterninterferometry and shearographic testing. Besides the basic principles of testing usingthese methods, their potential applications in various industrial and technologicalbranches are broadly discussed. The analysis as categorization of the NDT methodsprovided in this paper may help in selection of such methods in diagnosis of varioustypes of structures and defects and damage occurring in these structures.展开更多
Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-l...Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.展开更多
When an underground structure passes through a liquefiable soil layer,the soil liquefaction may pose a significant threat to the structure.A centrifuge shaking table test was performed to research the seismic response...When an underground structure passes through a liquefiable soil layer,the soil liquefaction may pose a significant threat to the structure.A centrifuge shaking table test was performed to research the seismic response of underground structures in liquefiable interlayer sites,and a valid numerical model was obtained through simulation model test.Finally,the calibrated numerical model was used to perform further research on the influence of various distribution characteristics of liquefiable interlayers on the seismic reaction of underground structures.The key findings are as follows.The structure faces the most unfavorable condition once a liquefiable layer is located in the middle of the underground structure.When a liquefiable layer exists in the middle of the structure,the seismic reactions of both the underground structure and model site will increase with the rise of the thickness of the liquefiable interlayer.The inter-story drift of the structure in the non-liquefiable site is much smaller than that in the liquefiable interlayer site.The inter-story drift of the structure is not only associated with the site displacement and the soil-structure stiffness ratio but also closely associated with the slippage of the soil-structure contact interface under the condition of large deformation of the site.展开更多
The bolted flange structure finds significant applications in fields such as aerospace,shipbuilding,and pipeline transportation.The investigation of its dynamic characteristics has consistently been a focal point for ...The bolted flange structure finds significant applications in fields such as aerospace,shipbuilding,and pipeline transportation.The investigation of its dynamic characteristics has consistently been a focal point for researchers;however,there remains a deficiency in the development of robust analytical models.This paper introduces a novel analytical model based on the finite element methods and the Timoshenko beam theory to accurately simulate the bolted flange structure.The stiffness,mass,damping,and inertia matrices of the rotor system are individually derived,and the dynamic equation is subsequently formulated.The model’s validity and accuracy are validated through both the experimental testing and the finite element analysis.This study aims to elucidate the relationship between the external loads and the influence of the geometric configuration on the stiffness and contact behavior of the bolted flange structure,thereby enabling a thorough and precise prediction of the static and dynamic load transfer pathways,as well as the distribution of vibrational energy within the structure,while also facilitating the incorporation of friction and slip effects.Simultaneously,this work provides a foundational framework for the optimization design of bolted flange structures,addressing the factors such as the number,size,and geometric distribution of bolts.展开更多
The steel-epoxy-steel sandwich structures provide enhanced corrosion resistance and fatigue resistance,making them suitable for pipeline rehabilitation with effective repair and long-term durability.However,the repair...The steel-epoxy-steel sandwich structures provide enhanced corrosion resistance and fatigue resistance,making them suitable for pipeline rehabilitation with effective repair and long-term durability.However,the repair quality can be compromised by disbond between the steel and epoxy layers,whichmay result frominsufficient epoxy injection.Conventional ultrasonic testing faces challenges in accurately locating disbond defects due to aliased echo interference at interfaces.This paper proposes a signal processing algorithm for improving the accuracy of ultrasonic reflection method for detecting disbond defects between steel and epoxy layers.First,a coati optimization algorithmvariational mode decomposition(COA-VMD)is applied to adaptively decompose the ultrasonic signals and extract the intrinsic mode function components that show high correlation with the defect-related signals.Then,by calculating the relative reflectance at the interface and establishing a quantitative evaluation index based on acoustic impedance discontinuity,the locations of disbond defects are identified.Experimental results demonstrate that this method can effectively detect the locations of disbond defects between steel and epoxy layers.展开更多
Experimental studies were conducted on two high-strength steel plate-frame structures with different truss spacings under various impact velocities to investigate the dynamic mechanical properties of hull plate-frame ...Experimental studies were conducted on two high-strength steel plate-frame structures with different truss spacings under various impact velocities to investigate the dynamic mechanical properties of hull plate-frame structures under drop weight impact.The results showed that decreasing the main beam spacing can effectively increase the structural stiffness,reduce the maximum deformation,and increase the damage range.Furthermore,to simulate the impact tests accurately,static and dynamic tensile tests at different strain rates were carried out,and the Cowper-Symonds model parameters were fitted via experimental data.The material properties obtained from the tensile tests were used as inputs for numerical simulations with the numerical results coincide with the experimental results.A systematic analysis and discussion were conducted on the effects of truss spacing and truss width on the dynamic response of the reinforced plates,and an optimal range for the ratio of truss spacing to truss width was proposed.In addition,a mesh size sensitivity analysis for ship hull plate frame collision simulations was performed.The applicability of the EPS,MMC,and RTCL failure criteria in the simulation of plate-frame structures was investigated via finite element simulations of falling weight impact tests.The research findings provide a reference for ship hull structure design and resilience assessment.展开更多
The field test of a typical Tibetan ancient structure instrumented with displacement and acceleration transducers was conducted to measure time histories due to crowd walking and running. The test case is introduced f...The field test of a typical Tibetan ancient structure instrumented with displacement and acceleration transducers was conducted to measure time histories due to crowd walking and running. The test case is introduced firstly. The displacement time histories are then used to analyze the dynamic property such as fundamental frequency of vertical vibration and damping ratio of the test structure, and the acceleration time histories are applied to evaluate the floor vibration serviceability. The floor interaction and comparison of human walking and running are also discussed. Some valuable conclusions are given.展开更多
It is considered thai the damage of the underground structures caused by earthquakes is minor for a long time. However, the catastrophic damages induced by several recent earthquakes （e. g. Kobe earthquake in 1995 ）...It is considered thai the damage of the underground structures caused by earthquakes is minor for a long time. However, the catastrophic damages induced by several recent earthquakes （e. g. Kobe earthquake in 1995 ） revealed that the study on the dynamic properties of the underground structures is indispensable. The dynamic behavior and damage mechanism of underground structure are analyzed by using shaking table tests （ both shallow-and deep-buried） and numerical simulation （3D FEM） including horizontal and vertical input motions, individually and simultaneously. From the results, the underground structure collapsed due to strong horizontal forces although vertical deformation is not negligible. The vertical excitation increases the response of structure, especially the stress and shear stress at the upper section; the soil influenced the property of soilstructure system. In the same excitation, the response in shallow-buried test is larger than deep case. Both overburden and vertical earthquake play important roles in the response of structure and those are two critical aspects in the design of the large-span underground structures, such as subway stations.展开更多
Smart material and structure (SMS) is a challenging novel technique for the 21 century especially in fields of aviation and aerospace. Vibration and noise suppression smart structure is an important branch of SMS. T...Smart material and structure (SMS) is a challenging novel technique for the 21 century especially in fields of aviation and aerospace. Vibration and noise suppression smart structure is an important branch of SMS. There are several typical structures such as the cabin of an airplane, space station, the solar board of satellite and the rotor blade of a helicopter, of which the vibrations and radiation noises have bad influences on precise equipments and aiming systems. In order to suppress vibrations and noises of these structures, several algorithms are applied to the models which simulate the structures. Experiments are performed to suppress vibrations and noises by bonding sensors and actuators to the structures at the optimized locations and using computer based measurement and control systems. For the blade vibration control of a helicopter, a non contact method of signal transmission by magneto electric coupling is discussed. The experimental results demonstrate that the methods used for active control are effective.展开更多
Adaptive truss structures are a new kind of structures with integrated active members,whose dynamic characteristies can be beneficially modified to meet mission requirements.Active members containing actuating and sen...Adaptive truss structures are a new kind of structures with integrated active members,whose dynamic characteristies can be beneficially modified to meet mission requirements.Active members containing actuating and sensing units are the major components of adaptive truss structures.Modeling of adaptive truss structures is a key step to analyze the structural dynamic characteristics.A new experimental modal analysis approach,in which active members are used as excitatiDn sources for modal test,has been proposed in this paper.The excitation forces generated by the active members, which are different from the excitation forces exerted on structures in the conventional modal test,are internal forces for the truss structures.The relation between internal excitation forces and external forces is revealed such that the traditional identification method can be adopted to obtain modal parameters of adaptive structures.Placement problem of the active member in adaptive truss structures is also discussed in this work. Modal test and analysis are conducted with a planar adaptive truss structure by using piezoelectric active members in order to verify the feasibility and effectiveness of the proposed method.展开更多
In this paper, the buoyancy, kinetic properties and stability of air floated structures have been studied by theoretical and experimental methods. The equations for calculation of the buoyancy of the air floated buoy ...In this paper, the buoyancy, kinetic properties and stability of air floated structures have been studied by theoretical and experimental methods. The equations for calculation of the buoyancy of the air floated buoy are derived according to the Boyler law and the equilibrium equations of the air floated structure are established. Through simplification of the air floated structure as a single freedom rigid body and spring system, the natural period of heaving and some kinetic properties are discussed. In the stability analysis, the formulas for calculation of the meta centric height are presented. The theoretical results are in good agreement with the data observed from the model test and prototype test. The air buoyancy decrease coefficient presented in this paper has a large influence on the floating state, stability and dynamic properties of the air floated structure. The stability of the air floated structure can also be judged by the parameter of meta centric height, and calculations show that the air floated structure is less stable than the conventional float.展开更多
Studies on landslides by the 2008 Wenchuan earthquake showed that topography was of great importance in amplifying the seismic shaking, and among other factors, lithology and slope structure controlled the spatial occ...Studies on landslides by the 2008 Wenchuan earthquake showed that topography was of great importance in amplifying the seismic shaking, and among other factors, lithology and slope structure controlled the spatial occurrence of slope failures. The present study carried out experiments on four rock slopes with steep angle of 60° by means of a shaking table. The recorded Wenchuan earthquake waves were scaled to excite the model slopes. Measurements from accelerometers installed on free surface of the model slope were analyzed, with much effort on timedomain acceleration responses to horizontal components of seismic shaking. It was found that the amplification factor of peak horizontal acceleration, RPHA, was increasing with elevation of each model slope, though the upper and lower halves of the slope exhibited different increasing patterns. As excitation intensity was increased, the drastic deterioration of the inner structure of each slope caused the sudden increase of RPHA in the upper slope part. In addition, the model simulating the soft rock slope produced the larger RPHA than the model simulating the hard rock slope by a maximum factor of 2.6. The layered model slope also produced the larger RPHA than the homogeneous model slope by a maximum factor of 2.7. The upper half of a slope was influenced more seriously by the effect of lithology, while the lower half was influenced more seriously by the effect of slope structure.展开更多
基金Liaoning Provincial Natural Science Foundation of China Under Grant No. 20052005
文摘This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.
基金the support of NVIDIA Corporation with the donation of the Titan Xp GPU used for this researchsupported by EPSRC grant EP/R002495/1the European Metrology Research Programme through grant 17IND08。
文摘Composite materials are increasingly used in the aerospace industry.To fully realise the weight saving potential along with superior mechanical properties that composites offer in safety critical applications,reliable Non-Destructive Testing(NDT)methods are required to prevent catastrophic failures.This paper will review the state of the art in the field and point to highlight the success and challenges that different NDT methods are faced to evaluate the integrity of critical aerospace composites.The focus will be on advanced certificated NDT methods for damage detection and characterization in composite laminates for use in the aircraft primary and secondary structures.
基金This project is financially supported by the National High Technology Research Development Program of China(863Program) by the National Natural Science Foundation of China(Grant No.50609015)
文摘To study ice-induced vibration of a compliant conical structure, a series of model tests were performed from 2004 to 2005. In the tests, the ice sheet before the compliant conical structure was found to fail in two-time breaking. From 2005 to 2006, this type of ice failure was studied through more groups of tests. The tests show that two-time breaking is the typical failure of ice before steep conical structures, and is controlled by other factors at the same time, such as ice speed and the angle of the cone.
基金Scientific Research Fund of Institute of Engineering Mechanics,CEA under Grant No.2016A06International Science & Technology Cooperation Program of China under Grant No.2014DFA70950National Natural Science Foundation of China under Grant Nos.51378478,51161120360
文摘A retrofitting technology using precast steel reinforced concrete（PSRC） panels is developed to improve the seismic performance of old masonry buildings. The PSRC panels are built up as an external PSRC wall system surrounding the existing masonry building. The PSRC walls are well connected to the existing masonry building, which provides enough confinement to effectively improve the ductility, strength, and stiffenss of old masonry structures. The PSRC panels are prefabricated in a factory, significantly reducing the situ work and associated construction time. To demonstrate the feasibility and mechanical effectivenss of the proposed retrofitting system, a full-scale five-story specimen was constructed. The retrofitting process was completed within five weeks with very limited indoor operation. The specimen was then tested in the lateral direction, which could potentially suffer sigifnicant damage in a large earthquake. The technical feasibility, construction workability, and seismic performance were thoroughly demonstrated by a full-scale specimen construction and pseudo-dynamic tests.
基金supported bythe National High Technology Research and Development Program of China(863Program,Grant No.2003AA602150-3)the National Natural Science Foundation of China(Grant No.50609015)
文摘For the study on the ice-induced vibration of a compliant mono-cone structure,a series of model tests were performed from 2004 to 2006.In these tests,the ice sheet before the compliant conical structure was found to be failed in two-time breaking.Based on this important finding,model tests study of the ice force on a compliant multi-cone structure were performed from 2006 to 2007.In these tests,the ice sheet broke before each single cone non-simultaneously.The exciting energy of the total ice force was found to be in a wide range of frequencies,and the structure can be easily excited with nonlinear resonance.
基金Project supported by the National Natural Science Foundation of China （No. 51378147）
文摘A pseudo-dynamic testing program was generated on a fabricated composite frame with steel plate shear walls （SPSWs） to study its seismic perlbrmance. The specimen was a three-storey single-bay frame, which was composed of H- section steel columns and composite beams, and was assembled by bolted height-adjustable steel beam-to-column connections （BHA connections）. Beam-only-connected SPSWs were selected as lateral load resisting members. The specimen was subjected to four ground motions of progressively increasing intensity. The results showed that： （1） beam-only-connected S PSWs provided sufficient lateral load resistance, lateral stiffness, and energy dissipation capacity to the fabricated frame via the tension ficld action developed in their infill panels; （2） the fabricated frame, assembled by BHA connections, exhibited substantial redundancy and good ductility; （3） an undesirable failure mode of the fabricated frame, in huge earthquakes, included severe cracking in composite beams and block shear failure in SPSWs＇ connections; （4） the inter-storey shear force distribution determined by ASCE/SE1 7-10 was verified with experimental data.
基金The Key Project of the Major Research Plan of Natural Science Foundation of China Under Grant No.90715036the Key Project of the Natural Science Foundation of China Under Grant No.50338020
文摘Modem dynamic tests such as networked collaborative pseudo-dynamic testing （PDT） provide new tools to study the dynamic performance of large and complex structures. In this paper, several networked collaborative PDT systems established in China and abroad are introduced, including a detailed description of the first networked collaborative platform that involved the construction of a standardized demonstration procedure for networked collaborative PDT. The example is a multi-span bridge with RC piers retrofitted by FRP, and a networked structural laboratory （NetSLab） platform is used to link distributed laboratories located at several universities together. Substructure technology is also used in the testing. The characteristics, resource sharing and collaborative work of NetSLab are described, and the results illustrate that use of the NetSLab is feasible for studying the dynamic performance of multi-span bridge structures.
文摘With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weight and increase the payload,composite material structures will be widely used. It is difficult to evaluate the strength and life of composite materials due to their complex mechanism and various phenomena in damage and failure.Meanwhile,the structures of composite materials used in spacecrafts will bear complex loads,including the coupling loads of tension,pressure,bending,shear,and torsion. Static loads,thermal loads,and vibration loads may occur at the same time,which asks for verification requirements to ensure the structure safety. Therefore,it is necessary to carry out a systematic multi-level experimental study. In this paper,the building block approach (BBA) is used to investigate the multilevel composite material structures for spacecrafts. The advanced measurement technology is adopted based on digital image correlation (DIC) and piezoelectric and optical fiber sensors to measure the composite material structure deformation. The virtual experiment technology is applied to provide sufficient and reliable data for the evaluation of the composite material structures of spacecrafts.
文摘Non-destructive testing (NDT) of structures is one of the most important tasksof the proper maintenance and diagnosis of machines and constructions structuralcondition. NDT methods contribute to the damage tolerance philosophy used in theaircraft design methodology as well as many other operation and maintenance programsof machinery and constructions. The following study is focusing on overviewing animportant group of NDT methods: the optical and other ones, which found broadapplicability in scientific and industrial studies nowadays. The paper discusses theselected most widely applicable methods, namely, visual testing, ultrasonic testing,radiographic testing, infrared thermography as well as electronic speckle patterninterferometry and shearographic testing. Besides the basic principles of testing usingthese methods, their potential applications in various industrial and technologicalbranches are broadly discussed. The analysis as categorization of the NDT methodsprovided in this paper may help in selection of such methods in diagnosis of varioustypes of structures and defects and damage occurring in these structures.
文摘Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.
基金National Natural Science Foundation of China under Grant No.52078020。
文摘When an underground structure passes through a liquefiable soil layer,the soil liquefaction may pose a significant threat to the structure.A centrifuge shaking table test was performed to research the seismic response of underground structures in liquefiable interlayer sites,and a valid numerical model was obtained through simulation model test.Finally,the calibrated numerical model was used to perform further research on the influence of various distribution characteristics of liquefiable interlayers on the seismic reaction of underground structures.The key findings are as follows.The structure faces the most unfavorable condition once a liquefiable layer is located in the middle of the underground structure.When a liquefiable layer exists in the middle of the structure,the seismic reactions of both the underground structure and model site will increase with the rise of the thickness of the liquefiable interlayer.The inter-story drift of the structure in the non-liquefiable site is much smaller than that in the liquefiable interlayer site.The inter-story drift of the structure is not only associated with the site displacement and the soil-structure stiffness ratio but also closely associated with the slippage of the soil-structure contact interface under the condition of large deformation of the site.
基金Project supported by the National Defense Technology Foundation Under the State Administration of Science,Technology,and Industry for National Defense of China(No.JSZL2022213A001)the Special Funds for Basic Research in Central Universities of China(No.HYGJZN202322)。
文摘The bolted flange structure finds significant applications in fields such as aerospace,shipbuilding,and pipeline transportation.The investigation of its dynamic characteristics has consistently been a focal point for researchers;however,there remains a deficiency in the development of robust analytical models.This paper introduces a novel analytical model based on the finite element methods and the Timoshenko beam theory to accurately simulate the bolted flange structure.The stiffness,mass,damping,and inertia matrices of the rotor system are individually derived,and the dynamic equation is subsequently formulated.The model’s validity and accuracy are validated through both the experimental testing and the finite element analysis.This study aims to elucidate the relationship between the external loads and the influence of the geometric configuration on the stiffness and contact behavior of the bolted flange structure,thereby enabling a thorough and precise prediction of the static and dynamic load transfer pathways,as well as the distribution of vibrational energy within the structure,while also facilitating the incorporation of friction and slip effects.Simultaneously,this work provides a foundational framework for the optimization design of bolted flange structures,addressing the factors such as the number,size,and geometric distribution of bolts.
基金supported by the Research Funding of Hangzhou International Innovation Institute of Beihang University(Grant No.015731201-2024KQ126)National Key R&D Program of China(Grant No.2023YFF0716600)National Natural Science Foundation of China(Grant No.62271021).
文摘The steel-epoxy-steel sandwich structures provide enhanced corrosion resistance and fatigue resistance,making them suitable for pipeline rehabilitation with effective repair and long-term durability.However,the repair quality can be compromised by disbond between the steel and epoxy layers,whichmay result frominsufficient epoxy injection.Conventional ultrasonic testing faces challenges in accurately locating disbond defects due to aliased echo interference at interfaces.This paper proposes a signal processing algorithm for improving the accuracy of ultrasonic reflection method for detecting disbond defects between steel and epoxy layers.First,a coati optimization algorithmvariational mode decomposition(COA-VMD)is applied to adaptively decompose the ultrasonic signals and extract the intrinsic mode function components that show high correlation with the defect-related signals.Then,by calculating the relative reflectance at the interface and establishing a quantitative evaluation index based on acoustic impedance discontinuity,the locations of disbond defects are identified.Experimental results demonstrate that this method can effectively detect the locations of disbond defects between steel and epoxy layers.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52171311 and 5227127).
文摘Experimental studies were conducted on two high-strength steel plate-frame structures with different truss spacings under various impact velocities to investigate the dynamic mechanical properties of hull plate-frame structures under drop weight impact.The results showed that decreasing the main beam spacing can effectively increase the structural stiffness,reduce the maximum deformation,and increase the damage range.Furthermore,to simulate the impact tests accurately,static and dynamic tensile tests at different strain rates were carried out,and the Cowper-Symonds model parameters were fitted via experimental data.The material properties obtained from the tensile tests were used as inputs for numerical simulations with the numerical results coincide with the experimental results.A systematic analysis and discussion were conducted on the effects of truss spacing and truss width on the dynamic response of the reinforced plates,and an optimal range for the ratio of truss spacing to truss width was proposed.In addition,a mesh size sensitivity analysis for ship hull plate frame collision simulations was performed.The applicability of the EPS,MMC,and RTCL failure criteria in the simulation of plate-frame structures was investigated via finite element simulations of falling weight impact tests.The research findings provide a reference for ship hull structure design and resilience assessment.
基金Acknowledgements The supports provided for the paper by the National Natural Science Foundation of China （Grant No. 50778019） and the Natural Science Foundation of Beijing （Grant No. 8092024） are gratefully appreciated.
文摘The field test of a typical Tibetan ancient structure instrumented with displacement and acceleration transducers was conducted to measure time histories due to crowd walking and running. The test case is introduced firstly. The displacement time histories are then used to analyze the dynamic property such as fundamental frequency of vertical vibration and damping ratio of the test structure, and the acceleration time histories are applied to evaluate the floor vibration serviceability. The floor interaction and comparison of human walking and running are also discussed. Some valuable conclusions are given.
文摘It is considered thai the damage of the underground structures caused by earthquakes is minor for a long time. However, the catastrophic damages induced by several recent earthquakes （e. g. Kobe earthquake in 1995 ） revealed that the study on the dynamic properties of the underground structures is indispensable. The dynamic behavior and damage mechanism of underground structure are analyzed by using shaking table tests （ both shallow-and deep-buried） and numerical simulation （3D FEM） including horizontal and vertical input motions, individually and simultaneously. From the results, the underground structure collapsed due to strong horizontal forces although vertical deformation is not negligible. The vertical excitation increases the response of structure, especially the stress and shear stress at the upper section; the soil influenced the property of soilstructure system. In the same excitation, the response in shallow-buried test is larger than deep case. Both overburden and vertical earthquake play important roles in the response of structure and those are two critical aspects in the design of the large-span underground structures, such as subway stations.
文摘Smart material and structure (SMS) is a challenging novel technique for the 21 century especially in fields of aviation and aerospace. Vibration and noise suppression smart structure is an important branch of SMS. There are several typical structures such as the cabin of an airplane, space station, the solar board of satellite and the rotor blade of a helicopter, of which the vibrations and radiation noises have bad influences on precise equipments and aiming systems. In order to suppress vibrations and noises of these structures, several algorithms are applied to the models which simulate the structures. Experiments are performed to suppress vibrations and noises by bonding sensors and actuators to the structures at the optimized locations and using computer based measurement and control systems. For the blade vibration control of a helicopter, a non contact method of signal transmission by magneto electric coupling is discussed. The experimental results demonstrate that the methods used for active control are effective.
文摘Adaptive truss structures are a new kind of structures with integrated active members,whose dynamic characteristies can be beneficially modified to meet mission requirements.Active members containing actuating and sensing units are the major components of adaptive truss structures.Modeling of adaptive truss structures is a key step to analyze the structural dynamic characteristics.A new experimental modal analysis approach,in which active members are used as excitatiDn sources for modal test,has been proposed in this paper.The excitation forces generated by the active members, which are different from the excitation forces exerted on structures in the conventional modal test,are internal forces for the truss structures.The relation between internal excitation forces and external forces is revealed such that the traditional identification method can be adopted to obtain modal parameters of adaptive structures.Placement problem of the active member in adaptive truss structures is also discussed in this work. Modal test and analysis are conducted with a planar adaptive truss structure by using piezoelectric active members in order to verify the feasibility and effectiveness of the proposed method.
文摘In this paper, the buoyancy, kinetic properties and stability of air floated structures have been studied by theoretical and experimental methods. The equations for calculation of the buoyancy of the air floated buoy are derived according to the Boyler law and the equilibrium equations of the air floated structure are established. Through simplification of the air floated structure as a single freedom rigid body and spring system, the natural period of heaving and some kinetic properties are discussed. In the stability analysis, the formulas for calculation of the meta centric height are presented. The theoretical results are in good agreement with the data observed from the model test and prototype test. The air buoyancy decrease coefficient presented in this paper has a large influence on the floating state, stability and dynamic properties of the air floated structure. The stability of the air floated structure can also be judged by the parameter of meta centric height, and calculations show that the air floated structure is less stable than the conventional float.
基金financially supported by the National Basic Research Program "973" Project of the Ministry of Science and Technology of the People’s Republic of China (Grant No. 2013CB733200)the National Science Found for Distinguished Young Scholars of China (Grant No. 41225011)the Chang Jiang Scholars Program of China and the open fund on "Research on largescale landslides triggered by the Wenchuan earthquake" provided by the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection
文摘Studies on landslides by the 2008 Wenchuan earthquake showed that topography was of great importance in amplifying the seismic shaking, and among other factors, lithology and slope structure controlled the spatial occurrence of slope failures. The present study carried out experiments on four rock slopes with steep angle of 60° by means of a shaking table. The recorded Wenchuan earthquake waves were scaled to excite the model slopes. Measurements from accelerometers installed on free surface of the model slope were analyzed, with much effort on timedomain acceleration responses to horizontal components of seismic shaking. It was found that the amplification factor of peak horizontal acceleration, RPHA, was increasing with elevation of each model slope, though the upper and lower halves of the slope exhibited different increasing patterns. As excitation intensity was increased, the drastic deterioration of the inner structure of each slope caused the sudden increase of RPHA in the upper slope part. In addition, the model simulating the soft rock slope produced the larger RPHA than the model simulating the hard rock slope by a maximum factor of 2.6. The layered model slope also produced the larger RPHA than the homogeneous model slope by a maximum factor of 2.7. The upper half of a slope was influenced more seriously by the effect of lithology, while the lower half was influenced more seriously by the effect of slope structure.
