In the study of the application effectiveness of deep-hole controlled pre-splittingblasting technology,it was found through laboratory micro test and field study on a mine insouth China that under the technology,coal ...In the study of the application effectiveness of deep-hole controlled pre-splittingblasting technology,it was found through laboratory micro test and field study on a mine insouth China that under the technology,coal masses produce many irreversible cracks.Afterblasting,the nearer the distance from blasting hole,the larger the BET surface areaand volume ratio of the infiltration pore are;they increased by 11.47%and 5.73%,respectively.The coefficient of air permeability is increased 4 times.After 3 months,the gasdrainage rate was increased by 66%.In the first 15 days,the cumulative pumped gas was1.93 times of blasting before.The average absolute gas emission decreased by 63.46%.Experimental results show that deep-hole controlled pre-splitting blasting not only preventscoal and gas outburst,but also gives good economic results.展开更多
This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality...This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality classification were determined based on wave theory of Kelvin medium.Then,a calculation model was obtained for the millisecond-delay cut blast vibration in Kelvin media using the Starfield charge superposition principle.Further,the influence of the delay time on the cut blast vibration was quantitatively analyzed and a method for calculating the reasonable cut blasting millisecond delay time is proposed according to the principle of dimensional analysis.Finally,field tests were used to verify the applicability of the method.The results show that 5 ms to 20 ms is a better detonator delay time range and cut blasting vibration can be effectively controlled using the delay time calculated by the calculation model described in this paper.展开更多
The present technical paper outlines the details of the controlled blasting techniques used to optimize blasting pattern for excavation of hard rock near the Bhira Earthen Dam in Maharashtra,India.In this connection,a...The present technical paper outlines the details of the controlled blasting techniques used to optimize blasting pattern for excavation of hard rock near the Bhira Earthen Dam in Maharashtra,India.In this connection,a series of experimental blasts were conducted by adjusting various blast design parameters at project site.The safe charge weight per delay was kept between 0.125 and 0.375 kg.The outcomes of these experimental blasts were analyzed to recommend optimized blasting patterns and methods for the overall excavation process during actual blasting operations.Blast design parameters,including the maximum quantity of explosive per delay,hole depth,burden and spacing between holes were optimized by using a site-specific attenuation equation,taking into account the proximity of the dam and tunnel from the blasting area.Peak particle velocity(PPV)level of 10 mm/s and 50 mm/s respectively were adopted as the safe vibration level for ensuring safety of the Bhira Earthen Dam and the nearby tunnel from the adverse effects of blast vibrations by analyzing the dominant frequency of ground vibrations observed and also by reviewing various international standards.Frequency of the ground vibrations observed on the dam and tunnel from majority of the blasts was found to be more than 10 Hz and 50 Hz respectively.During the entire period of blasting,the blast vibrations were recorded to be far lower than the safe vibration level set for these structures.Maximum Vibration level of about 0.8 mm/s and 35 mm/s were observed on dam and tunnel respectively which are far lower than the safe vibration level adopted for these structures.Hence,the entire excavation work was completed successfully and safely,without endangering the safety of dam or tunnel.展开更多
In order to solve the problems of top-coal inadequate destruction and large amounts of gas emission in mining extra thick and hard coal seam,this study investigated the pre-splitting for deep borehole blasting and gas...In order to solve the problems of top-coal inadequate destruction and large amounts of gas emission in mining extra thick and hard coal seam,this study investigated the pre-splitting for deep borehole blasting and gas pre-draining technologies on top coal.The mechanism of the technologies was systematically expounded based on hard top-coal cracks development obtained by numerical simulation and theoretical analysis.The results show that explosive blasting in the hard rock results in a large number of cracks and large displacement in the rock mass due to the effect of explosion stress.Meanwhile,the thick top-coal caves,and desorbing gas flows along the cracks improve gas extraction.Finally,the pre-splitting for deep borehole blasting and gas pre-draining technologies was applied in No.3802 working face of Shui Liandong Coal Mine,which increases monthly output in the face to 67.34 kt and the drained gas concentration to 86.2%.The drained gas average concentration from each borehole reaches 40%,and the effect is remarkable.展开更多
With the development of fracture mechanics,the fracture plane control blasting with notched borcholes hascome into being.This technique is used to create a satisfactory presplit along the contour of an excavation inro...With the development of fracture mechanics,the fracture plane control blasting with notched borcholes hascome into being.This technique is used to create a satisfactory presplit along the contour of an excavation inrock.However,the amount of explosive loaded in each hol usually is determined by trial and error.Because ofthis,two approaches estimating the amount of explosive for the blasting technique are suggested.展开更多
The mechanism of ground vibration in building demolition blasting was investigated,taking into account the prevailing influential factors, including the building's heightof mass center, the quantity size, the stru...The mechanism of ground vibration in building demolition blasting was investigated,taking into account the prevailing influential factors, including the building's heightof mass center, the quantity size, the structural feature, the component material quantity,the demolition method, the geological structure of the region, earthquake resistance rank,as well as the earthquake wave dissemination.The proposed method was applied efficientlyto reduce the blasting effects on the environment, which enriches the control theoriesof vibration caused by collapse in the blasting process and may provide a good referencefor the related engineering practices.展开更多
After a thorough review of some controllable parameters,which included field investigations,cavern dimensions,explosive,rock strength etc.,cut,contour,lifters and stoping holes were introduced for blasting cavern of n...After a thorough review of some controllable parameters,which included field investigations,cavern dimensions,explosive,rock strength etc.,cut,contour,lifters and stoping holes were introduced for blasting cavern of nucleus submarine.These design were conducted using a U.Langefors and B.Kihlstrom theory.展开更多
Based on experiments in lab, this paper analyzes the mechanism of directional broken controlled blasting and applies the technology to the cutting by utilizing its characteristic. The model cutting experiment and the ...Based on experiments in lab, this paper analyzes the mechanism of directional broken controlled blasting and applies the technology to the cutting by utilizing its characteristic. The model cutting experiment and the practical application result show that the cutting blasting technology is an effective way.展开更多
Blasting operation dissipates much of the blasting energy in crushing the rock at the borehole and the resulting cracks are randomly oriented. There is very little control of the fracture plane. In order to control th...Blasting operation dissipates much of the blasting energy in crushing the rock at the borehole and the resulting cracks are randomly oriented. There is very little control of the fracture plane. In order to control the fracture plane, many methods have been applied. This paper discusses a new blasting method in which a high degree of fracture control can be achieved while minimizing the ground shock.展开更多
This paper analyses the fragmenting principle of static blasting agent (SBA) and the action of its cutting fragmentation. Using SBA for sterming material proved very useful and advantageous. Here we analyse in detail ...This paper analyses the fragmenting principle of static blasting agent (SBA) and the action of its cutting fragmentation. Using SBA for sterming material proved very useful and advantageous. Here we analyse in detail the cutting action of pre- stress and stress wave in pre-stressing force blasting.展开更多
In recent years, China's overall social and economic system has undergone rapid and effective development under the promotion of personnel in various scientific research aspects. Driven by the economy, many indust...In recent years, China's overall social and economic system has undergone rapid and effective development under the promotion of personnel in various scientific research aspects. Driven by the economy, many industries in China have encountered many challenges with the advantages of such a large economic environment, but not only many challenges appear, but also challenges have also brought a lot of development opportunities. Enterprises to seize these opportunities can greatly promote their own economic rapid and effective development. Driven by the development of the social and economic system, the coal mining industry continues to develop through many measures. However, at present, the open-pit coal mines in China will produce a great vibration during blasting, which has brought a lot of harmful effects to the coal mining land. If these harmful effects are not effectively controlled, then for the coal mining enterprises will not only cause great damage to the machinery and equipment, in many cases, there will even endanger the life safety and property safety of the personnel on the site.展开更多
The study was conducted to reduce blast damage, the use of pesticides residue, environment pollution and control costs, and to make a significant contribution to the improvement of grain production, quality and agricu...The study was conducted to reduce blast damage, the use of pesticides residue, environment pollution and control costs, and to make a significant contribution to the improvement of grain production, quality and agriculture ecological environment. Over these years, by the methods of systematical monitoring, regular surveys, field investigation, rice blast resistance identification, experiments and meteorological data analysis, the study on comprehensive prevention and control of rice blast in Nanchong City was conducted. The results showed that the rice varieties more sensitive to blast had a higher incidence of severe blast disease. Replacing,varieties with different source of resistance every three to five years and reasonable variety distribution can effectively reduce the prevalence of rice blast. Appropriate treatment of infected rice straw and pathogen, seed disinfection, seedling disinfection, and pesticide application at transplanting and etc. can delay blast occurrence and reduce the damage caused by blast. By analyzing the blast control efficiency of pesticides applied at different growth stages, we found that best control efficiency against blast was achieved by spraying pesticide twice during the whole growth stage, once 3 d before transplanting or 10 d after transplanting; and once at initial heading stage. Spraying 525 g/hm^2 75% tricyclazole was proven to be the best dosage for blast control. However, 375-450 g/hm^2 75% tricyclazole is enough if the blast incidence is not severe, or the rice varieties are slightly susceptible to blast.The control efficiency against leaf blast between 4% kasugamycin and 20% tricyclazole had no significant difference, but was significantly higher than that of 100 billion spores/g of Bacillus subtilis. The control efficiency against neck blast had no significant difference among 4% kasugamycin, 20% tricyclazole and 100 billion spores/g of B. subtilis. 450 g/hm^2 75% tricyclazole had better control efficiency against neck blast than 2 250 g/hm^2 2% 800 million spores/g Jinggangmycin-wax bud bacteria SC, 1 050 g/hm^2 41% kasugamycin-isoprothiolane WP and 900 g/hm^2 41%kasugamycin-isoprothiolane WP. The frequency of severe blast incidence in Nanchong City has reached 50% since 1997. The rice blast disease has been effectively controlled by comprehensive prevention and control technology, reducing the production loss to less than 2%, and pesticides by 4 523 t in total. In 2014, 327000 t rice grains were approved as pollution-free, green and organic agricultural products, indicating that the blast control measures produced great economic, social and ecological values.展开更多
The article systematically summarizes the pathogen, incidence law and disease symptom of rice blast, and raises the integrated control technique for the disease, which will provide the certain theoretical basis for th...The article systematically summarizes the pathogen, incidence law and disease symptom of rice blast, and raises the integrated control technique for the disease, which will provide the certain theoretical basis for the control of the disease, being benefit for the actual production of rice in field.展开更多
At the beginning of 1990s, Shougang blast furnaces （BFs） No. 2, No. 4, No. 3 and No. 1 were rebuilt se quently for new technological modernization in succession. The campaign life of BFs No. 1, No. 3 and No. 4 reach...At the beginning of 1990s, Shougang blast furnaces （BFs） No. 2, No. 4, No. 3 and No. 1 were rebuilt se quently for new technological modernization in succession. The campaign life of BFs No. 1, No. 3 and No. 4 reaches 16.4, 17.6 and 15.6 years, respectively, and the hot metal output of one campaign reaches 33.8, 35.48 and 26.37 Mt, respectively; the hot metal output of BF effective volume of one campaign reaches 13328, 13991 and 12560 t/m^3, respectively, which reaches the international advanced level of BF high efficiency and long campaign life. In BF desig-ning, several advanced BF long campaign technologies were adopted. BF proper inner profile was optimized, reasona- ble inner profile was adopted, and closed circulating soften water cooling technology was applied in 4 BFs. Double row cooling pipe high efficiency cooling stave was developed which could prolong the service life of bosh, belly and stack. Hot pressed carbon brick and ceramic cup hearth lining structure were applied and optimized. BF operation was improved continuously to ensure stable and smooth operation of BF. Hearth working condition control was strengthened, burden distribution control technology was applied to achieve reasonable distribution of gas flow, and heat load monitoring was strengthened to maintain BF reasonable working inner profile. Proper maintenance at the end of BF campaign was enhanced. Hearth and bottom service life was prolonged by adding titaniferous material and enhancing hearth cooling. Gunning of lining was carried out periodically for the area above tuyere zone.展开更多
In the process of blasting excavation, stress wave propagation and gas expansion can basically induce damage to surrounding rocks, which is detrimental to rock mass integrity and engineering safety. In this case, eval...In the process of blasting excavation, stress wave propagation and gas expansion can basically induce damage to surrounding rocks, which is detrimental to rock mass integrity and engineering safety. In this case, evaluation and control of blast-induced effects are essential to the safety of nearby buildings and integrity of bedrock in blasting field. In Fangchenggang nuclear power station of China, the drill-and- blast method was employed for bedrock excavation. In order to reduce the blast-induced damage zone, the wave propagation and associated damage to rock mass should be carefully investigated. In this paper, the wave propagation regressively obtained from field monitoring data was presented based on empirical formula （e.g. Sadovsloj formula）. The relationship between the peak particle velocity （PPV） at a distance of 30 m away from the charge hole and charge per delay in blast design was derived. Meanwhile, the acoustic tests before and after blasting were conducted to determine the damage depth of rock mass. The charge per delay in blast design was then calibrated based on the blast-induced wave propagation regularity. The results showed that a satisfactory effect was achieved on blast-induced damage control of rock mass. This could be helpful to rock damage control in similar blasting projects.展开更多
Field experiments of mixed- (intercropping) and pure-planting (monoculture) of four rice varieties, representing improved hybrid varieties (Shanyou63 and Shanyou22) and high-quality traditional varieties (Huangkenuo a...Field experiments of mixed- (intercropping) and pure-planting (monoculture) of four rice varieties, representing improved hybrid varieties (Shanyou63 and Shanyou22) and high-quality traditional varieties (Huangkenuo and Zigu) from Yunnan Province, were conducted based on their differences in genetic background and agro-economical characteristics. The results demonstrated that the mixed-planting of the hybrid rice and high-quality traditional rice varieties had a significantly greater effect on controlling rice blast disease than the monoculture of these varieties, particularly the traditional ones. It is evident for the highly susceptible traditional varieties in mixed-planting to achieve disease control, with significant decreases in blast incidences and severity indexes. The blast control efficiency reached up to 83-98% under such planting model. This suggests that an appropriate mixed-planting of rice varieties with diverse genetic background and agro-economical characteristics is an effective approach for rice blast control. In addition, resistance of the traditional rice varieties to lodging was considerably increased in the plots with mixed-planting, compared with the plots with monoculture. The average rate of grain-yield increase ranged from 6. 5 to 9.7% in the plots with mixed-planting.展开更多
Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a...Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting. Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability.These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans.Finally, a new methodology is proposed.展开更多
The deformation control of surrounding rock in gobside roadway with thick and hard roof poses a significant challenge to the safety and efficiency of coal mining.To address this issue,a novel approach combining direct...The deformation control of surrounding rock in gobside roadway with thick and hard roof poses a significant challenge to the safety and efficiency of coal mining.To address this issue,a novel approach combining directional and non-directional blasting techniques,known as combined blasting,was proposed.This study focuses on the experimental investigation of the proposed method in the 122108 working face in Caojiatan Coal Mine as the engineering background.The initial phase of the study involves physical model experiments to reveal the underlying mechanisms of combined blasting for protecting gob-side roadway with thick and hard roof.The results demonstrate that this approach effectively accelerates the collapse of thick and hard roofs,enhances the fragmentation and expansion coefficient of gangue,facilitates the filling of the goaf with gangue,and provides support to the overlying strata,thus reducing the subsidence of the overlying strata above the goaf.Additionally,the method involves cutting the main roof into shorter beams to decrease the stress and disrupt stress transmission pathways.Subsequent numerical simulations were conducted to corroborate the findings of the physical model experiments,thus validating the accuracy of the experimental results.Furthermore,field engineering experiments were performed,affirming the efficacy of the combined blasting method in mitigating the deformation of surrounding rock and achieving the desired protection of the gob-side roadway.展开更多
The key technologies of precision blasting were put forward based on the characteristics of urban via- duct blasting demolition in complicated surroundings. Initial bending instability mechanics model of reinforcing s...The key technologies of precision blasting were put forward based on the characteristics of urban via- duct blasting demolition in complicated surroundings. Initial bending instability mechanics model of reinforcing steel bar frame of blasting fragmented pier and sequenced collapsed dynamic model were established for quanti- tative blasting design. Technologies of water pressure blasting were applied in multi-cell box girder fragmenta- tion. The detonating network of non-electric duplication crossover was adopted for the safety and reliability of ultra-long delay. The rationality of blasting scheme and parameters were validated by physical model test. Harm- ful effects were forecasted and controlled by integrated protective technologies. Specialization, cooperation, pre- cision, execution （SCPE） project management method was put forward for precision management. The key tech- nologies of precision demolition blasting can provide reference for similar proiects.展开更多
基金Supported by Project from National Natural Science Foundation of China(50674111)the National key Technology R&D Program in 10th Five Years Plan of China
文摘In the study of the application effectiveness of deep-hole controlled pre-splittingblasting technology,it was found through laboratory micro test and field study on a mine insouth China that under the technology,coal masses produce many irreversible cracks.Afterblasting,the nearer the distance from blasting hole,the larger the BET surface areaand volume ratio of the infiltration pore are;they increased by 11.47%and 5.73%,respectively.The coefficient of air permeability is increased 4 times.After 3 months,the gasdrainage rate was increased by 66%.In the first 15 days,the cumulative pumped gas was1.93 times of blasting before.The average absolute gas emission decreased by 63.46%.Experimental results show that deep-hole controlled pre-splitting blasting not only preventscoal and gas outburst,but also gives good economic results.
基金National Natural Science Foundation of China under Grant Nos.51979205 and 51939008。
文摘This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality classification were determined based on wave theory of Kelvin medium.Then,a calculation model was obtained for the millisecond-delay cut blast vibration in Kelvin media using the Starfield charge superposition principle.Further,the influence of the delay time on the cut blast vibration was quantitatively analyzed and a method for calculating the reasonable cut blasting millisecond delay time is proposed according to the principle of dimensional analysis.Finally,field tests were used to verify the applicability of the method.The results show that 5 ms to 20 ms is a better detonator delay time range and cut blasting vibration can be effectively controlled using the delay time calculated by the calculation model described in this paper.
文摘The present technical paper outlines the details of the controlled blasting techniques used to optimize blasting pattern for excavation of hard rock near the Bhira Earthen Dam in Maharashtra,India.In this connection,a series of experimental blasts were conducted by adjusting various blast design parameters at project site.The safe charge weight per delay was kept between 0.125 and 0.375 kg.The outcomes of these experimental blasts were analyzed to recommend optimized blasting patterns and methods for the overall excavation process during actual blasting operations.Blast design parameters,including the maximum quantity of explosive per delay,hole depth,burden and spacing between holes were optimized by using a site-specific attenuation equation,taking into account the proximity of the dam and tunnel from the blasting area.Peak particle velocity(PPV)level of 10 mm/s and 50 mm/s respectively were adopted as the safe vibration level for ensuring safety of the Bhira Earthen Dam and the nearby tunnel from the adverse effects of blast vibrations by analyzing the dominant frequency of ground vibrations observed and also by reviewing various international standards.Frequency of the ground vibrations observed on the dam and tunnel from majority of the blasts was found to be more than 10 Hz and 50 Hz respectively.During the entire period of blasting,the blast vibrations were recorded to be far lower than the safe vibration level set for these structures.Maximum Vibration level of about 0.8 mm/s and 35 mm/s were observed on dam and tunnel respectively which are far lower than the safe vibration level adopted for these structures.Hence,the entire excavation work was completed successfully and safely,without endangering the safety of dam or tunnel.
基金financially supported by the National Natural Science Fund of China(Nos.51004003 and 51474009)Anhui Province Education Department Natural Science Fund Key Project of China(No.KJ2010A091)
文摘In order to solve the problems of top-coal inadequate destruction and large amounts of gas emission in mining extra thick and hard coal seam,this study investigated the pre-splitting for deep borehole blasting and gas pre-draining technologies on top coal.The mechanism of the technologies was systematically expounded based on hard top-coal cracks development obtained by numerical simulation and theoretical analysis.The results show that explosive blasting in the hard rock results in a large number of cracks and large displacement in the rock mass due to the effect of explosion stress.Meanwhile,the thick top-coal caves,and desorbing gas flows along the cracks improve gas extraction.Finally,the pre-splitting for deep borehole blasting and gas pre-draining technologies was applied in No.3802 working face of Shui Liandong Coal Mine,which increases monthly output in the face to 67.34 kt and the drained gas concentration to 86.2%.The drained gas average concentration from each borehole reaches 40%,and the effect is remarkable.
文摘With the development of fracture mechanics,the fracture plane control blasting with notched borcholes hascome into being.This technique is used to create a satisfactory presplit along the contour of an excavation inrock.However,the amount of explosive loaded in each hol usually is determined by trial and error.Because ofthis,two approaches estimating the amount of explosive for the blasting technique are suggested.
文摘The mechanism of ground vibration in building demolition blasting was investigated,taking into account the prevailing influential factors, including the building's heightof mass center, the quantity size, the structural feature, the component material quantity,the demolition method, the geological structure of the region, earthquake resistance rank,as well as the earthquake wave dissemination.The proposed method was applied efficientlyto reduce the blasting effects on the environment, which enriches the control theoriesof vibration caused by collapse in the blasting process and may provide a good referencefor the related engineering practices.
文摘After a thorough review of some controllable parameters,which included field investigations,cavern dimensions,explosive,rock strength etc.,cut,contour,lifters and stoping holes were introduced for blasting cavern of nucleus submarine.These design were conducted using a U.Langefors and B.Kihlstrom theory.
文摘Based on experiments in lab, this paper analyzes the mechanism of directional broken controlled blasting and applies the technology to the cutting by utilizing its characteristic. The model cutting experiment and the practical application result show that the cutting blasting technology is an effective way.
文摘Blasting operation dissipates much of the blasting energy in crushing the rock at the borehole and the resulting cracks are randomly oriented. There is very little control of the fracture plane. In order to control the fracture plane, many methods have been applied. This paper discusses a new blasting method in which a high degree of fracture control can be achieved while minimizing the ground shock.
文摘This paper analyses the fragmenting principle of static blasting agent (SBA) and the action of its cutting fragmentation. Using SBA for sterming material proved very useful and advantageous. Here we analyse in detail the cutting action of pre- stress and stress wave in pre-stressing force blasting.
文摘In recent years, China's overall social and economic system has undergone rapid and effective development under the promotion of personnel in various scientific research aspects. Driven by the economy, many industries in China have encountered many challenges with the advantages of such a large economic environment, but not only many challenges appear, but also challenges have also brought a lot of development opportunities. Enterprises to seize these opportunities can greatly promote their own economic rapid and effective development. Driven by the development of the social and economic system, the coal mining industry continues to develop through many measures. However, at present, the open-pit coal mines in China will produce a great vibration during blasting, which has brought a lot of harmful effects to the coal mining land. If these harmful effects are not effectively controlled, then for the coal mining enterprises will not only cause great damage to the machinery and equipment, in many cases, there will even endanger the life safety and property safety of the personnel on the site.
基金Supported by Notice on the First Batch of National Modern Agricultural Demonstration Zone by the Ministry of Agriculture(Agricultural Project No.[2010]22)One of the Major Pest and Disease Early Warning and Prevention Research Programs for Main Grain and Oil Crops(N1997-ZC002)~~
文摘The study was conducted to reduce blast damage, the use of pesticides residue, environment pollution and control costs, and to make a significant contribution to the improvement of grain production, quality and agriculture ecological environment. Over these years, by the methods of systematical monitoring, regular surveys, field investigation, rice blast resistance identification, experiments and meteorological data analysis, the study on comprehensive prevention and control of rice blast in Nanchong City was conducted. The results showed that the rice varieties more sensitive to blast had a higher incidence of severe blast disease. Replacing,varieties with different source of resistance every three to five years and reasonable variety distribution can effectively reduce the prevalence of rice blast. Appropriate treatment of infected rice straw and pathogen, seed disinfection, seedling disinfection, and pesticide application at transplanting and etc. can delay blast occurrence and reduce the damage caused by blast. By analyzing the blast control efficiency of pesticides applied at different growth stages, we found that best control efficiency against blast was achieved by spraying pesticide twice during the whole growth stage, once 3 d before transplanting or 10 d after transplanting; and once at initial heading stage. Spraying 525 g/hm^2 75% tricyclazole was proven to be the best dosage for blast control. However, 375-450 g/hm^2 75% tricyclazole is enough if the blast incidence is not severe, or the rice varieties are slightly susceptible to blast.The control efficiency against leaf blast between 4% kasugamycin and 20% tricyclazole had no significant difference, but was significantly higher than that of 100 billion spores/g of Bacillus subtilis. The control efficiency against neck blast had no significant difference among 4% kasugamycin, 20% tricyclazole and 100 billion spores/g of B. subtilis. 450 g/hm^2 75% tricyclazole had better control efficiency against neck blast than 2 250 g/hm^2 2% 800 million spores/g Jinggangmycin-wax bud bacteria SC, 1 050 g/hm^2 41% kasugamycin-isoprothiolane WP and 900 g/hm^2 41%kasugamycin-isoprothiolane WP. The frequency of severe blast incidence in Nanchong City has reached 50% since 1997. The rice blast disease has been effectively controlled by comprehensive prevention and control technology, reducing the production loss to less than 2%, and pesticides by 4 523 t in total. In 2014, 327000 t rice grains were approved as pollution-free, green and organic agricultural products, indicating that the blast control measures produced great economic, social and ecological values.
文摘The article systematically summarizes the pathogen, incidence law and disease symptom of rice blast, and raises the integrated control technique for the disease, which will provide the certain theoretical basis for the control of the disease, being benefit for the actual production of rice in field.
文摘At the beginning of 1990s, Shougang blast furnaces （BFs） No. 2, No. 4, No. 3 and No. 1 were rebuilt se quently for new technological modernization in succession. The campaign life of BFs No. 1, No. 3 and No. 4 reaches 16.4, 17.6 and 15.6 years, respectively, and the hot metal output of one campaign reaches 33.8, 35.48 and 26.37 Mt, respectively; the hot metal output of BF effective volume of one campaign reaches 13328, 13991 and 12560 t/m^3, respectively, which reaches the international advanced level of BF high efficiency and long campaign life. In BF desig-ning, several advanced BF long campaign technologies were adopted. BF proper inner profile was optimized, reasona- ble inner profile was adopted, and closed circulating soften water cooling technology was applied in 4 BFs. Double row cooling pipe high efficiency cooling stave was developed which could prolong the service life of bosh, belly and stack. Hot pressed carbon brick and ceramic cup hearth lining structure were applied and optimized. BF operation was improved continuously to ensure stable and smooth operation of BF. Hearth working condition control was strengthened, burden distribution control technology was applied to achieve reasonable distribution of gas flow, and heat load monitoring was strengthened to maintain BF reasonable working inner profile. Proper maintenance at the end of BF campaign was enhanced. Hearth and bottom service life was prolonged by adding titaniferous material and enhancing hearth cooling. Gunning of lining was carried out periodically for the area above tuyere zone.
基金supported by the Key Program of National Natural Science Foundation of China(Grant No.51439008)National Natural Science Foundation of China(Grant Nos.41572307 and51779248)National Natural Science Funds for Distinguished Young Scholar of China(Grant No.41525009)
文摘In the process of blasting excavation, stress wave propagation and gas expansion can basically induce damage to surrounding rocks, which is detrimental to rock mass integrity and engineering safety. In this case, evaluation and control of blast-induced effects are essential to the safety of nearby buildings and integrity of bedrock in blasting field. In Fangchenggang nuclear power station of China, the drill-and- blast method was employed for bedrock excavation. In order to reduce the blast-induced damage zone, the wave propagation and associated damage to rock mass should be carefully investigated. In this paper, the wave propagation regressively obtained from field monitoring data was presented based on empirical formula （e.g. Sadovsloj formula）. The relationship between the peak particle velocity （PPV） at a distance of 30 m away from the charge hole and charge per delay in blast design was derived. Meanwhile, the acoustic tests before and after blasting were conducted to determine the damage depth of rock mass. The charge per delay in blast design was then calibrated based on the blast-induced wave propagation regularity. The results showed that a satisfactory effect was achieved on blast-induced damage control of rock mass. This could be helpful to rock damage control in similar blasting projects.
基金This research was supported by the National Natural Science Foundation of China and Natural Science Foundation of Yunnan(01NG10,01C0007Z,AA211091 and 30160048)the Shanghai Commission of Education(00XD14006).
文摘Field experiments of mixed- (intercropping) and pure-planting (monoculture) of four rice varieties, representing improved hybrid varieties (Shanyou63 and Shanyou22) and high-quality traditional varieties (Huangkenuo and Zigu) from Yunnan Province, were conducted based on their differences in genetic background and agro-economical characteristics. The results demonstrated that the mixed-planting of the hybrid rice and high-quality traditional rice varieties had a significantly greater effect on controlling rice blast disease than the monoculture of these varieties, particularly the traditional ones. It is evident for the highly susceptible traditional varieties in mixed-planting to achieve disease control, with significant decreases in blast incidences and severity indexes. The blast control efficiency reached up to 83-98% under such planting model. This suggests that an appropriate mixed-planting of rice varieties with diverse genetic background and agro-economical characteristics is an effective approach for rice blast control. In addition, resistance of the traditional rice varieties to lodging was considerably increased in the plots with mixed-planting, compared with the plots with monoculture. The average rate of grain-yield increase ranged from 6. 5 to 9.7% in the plots with mixed-planting.
文摘Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting. Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability.These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans.Finally, a new methodology is proposed.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52074298 and 52204164)Fundamental Research Funds for the Central Universities(Grant No.2022XJSB03).
文摘The deformation control of surrounding rock in gobside roadway with thick and hard roof poses a significant challenge to the safety and efficiency of coal mining.To address this issue,a novel approach combining directional and non-directional blasting techniques,known as combined blasting,was proposed.This study focuses on the experimental investigation of the proposed method in the 122108 working face in Caojiatan Coal Mine as the engineering background.The initial phase of the study involves physical model experiments to reveal the underlying mechanisms of combined blasting for protecting gob-side roadway with thick and hard roof.The results demonstrate that this approach effectively accelerates the collapse of thick and hard roofs,enhances the fragmentation and expansion coefficient of gangue,facilitates the filling of the goaf with gangue,and provides support to the overlying strata,thus reducing the subsidence of the overlying strata above the goaf.Additionally,the method involves cutting the main roof into shorter beams to decrease the stress and disrupt stress transmission pathways.Subsequent numerical simulations were conducted to corroborate the findings of the physical model experiments,thus validating the accuracy of the experimental results.Furthermore,field engineering experiments were performed,affirming the efficacy of the combined blasting method in mitigating the deformation of surrounding rock and achieving the desired protection of the gob-side roadway.
文摘The key technologies of precision blasting were put forward based on the characteristics of urban via- duct blasting demolition in complicated surroundings. Initial bending instability mechanics model of reinforcing steel bar frame of blasting fragmented pier and sequenced collapsed dynamic model were established for quanti- tative blasting design. Technologies of water pressure blasting were applied in multi-cell box girder fragmenta- tion. The detonating network of non-electric duplication crossover was adopted for the safety and reliability of ultra-long delay. The rationality of blasting scheme and parameters were validated by physical model test. Harm- ful effects were forecasted and controlled by integrated protective technologies. Specialization, cooperation, pre- cision, execution （SCPE） project management method was put forward for precision management. The key tech- nologies of precision demolition blasting can provide reference for similar proiects.
