The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected ...The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected to both pre-compression and pre-aging exhibits the most refined and densest distribution of precipitates upon aging at 200℃,leading to the superior age-hardening performance observed in the alloy.Comparatively,the alloy that underwent only pre-aging displayed a greater number density of precipitates than its counterpart that was neither pre-compressed nor pre-aged when both were aged to their peak conditions at 200℃,indicating an enhanced age-hardening response in the pre-aged alloy.The precipitates in these three peak-aged alloys consist of Mg_(2)Sn and MgZn_(2)phases.The reason why the pre-aged alloy has a higher number density of precipitates than the directly aged alloy is that MgZn_(2)phase formed during pre-aging can serve as heterogeneous nucleation site for the formation of Mg_(2)Sn.The reason why the pre compression and pre-aged alloy has the highest number density of precipitates is that Mg_(3)Sn and MgZn_(2)phases formed during pre-aging,alongside lattice defects introduced during pre-compression,collectively act as effective heterogeneous nucleation sites for the formation of Mg_(2)Sn during the subsequent aging at 200℃.展开更多
The combined effects of isothermal annealing and pre-compression on the mechanical properties of Cu36Zr48Al8Ag8 bulk metallic glass （BMG） were investigated. The as-cast specimens were first annealed at 743 K for 10 ...The combined effects of isothermal annealing and pre-compression on the mechanical properties of Cu36Zr48Al8Ag8 bulk metallic glass （BMG） were investigated. The as-cast specimens were first annealed at 743 K for 10 min, and then pre-compressed under 800 MPa for 1, 3, 5 and 10 h, respectively. The results indicated that annealing resulted in the formation of nanocrystals with a diameter of -10 nm in the amorphous matrix and a drastic decrease of the free volume, leading to complete loss of the plasticity of the BMG. Applying pre-compression under a stress of 800 MPa for a proper duration （5 h） resumed part of the lost free volume in the BMG matrix and therefore partially recovered the plasticity. A very long period of pre-compression （10 h） decreased the free volume again, which was caused by the excessive crystal growth.展开更多
Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump wi...Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difticult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic（including fluid compressibility and viscosity） and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13~, the PCV volume is 1.3 ~ I0-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13~. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/rain, 1 500 r/rain, the swash plate angle is ll~, 13~, 15~ and 17~, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.展开更多
In this work, pre-strain annealing strengthening(PSAS) effect was investigated in an extruded Mg-1.0Gd-1.5 Zn(wt.%) alloy with respect to different grain sizes. The evolution of microstructures was provided by scannin...In this work, pre-strain annealing strengthening(PSAS) effect was investigated in an extruded Mg-1.0Gd-1.5 Zn(wt.%) alloy with respect to different grain sizes. The evolution of microstructures was provided by scanning electron microscopy(SEM), electron backscattered diffraction(EBSD), transmission electron microscopy(TEM) and high-angle annular dark-field scanning transmission electron microscopy(HAADF-STEM) under the initial state, pre-compression, intermediate annealing and re-compression conditions. The obtained results showed a grain size-dependent PSAS effect in the alloy. The sample with larger grain sizes corresponded to a higher strengthening effect, which mainly resulted from a more remarkable hindrance for the growth of existing twins and a larger proportion of activation for the nucleation of new twins. This was closely associated with the increase of back stress and friction stress for twin boundary motion impeded by the larger restraint of dislocations, the higher stress field surrounding solutes and the more Zn segregation. In addition to twinning behavior, Guinier Preston(G.P.) zones on basaldislocations were found after intermediate annealing and provided an extra strengthening by inhibiting the motions of gilding pre-existing dislocations and newly formed ones, but it was independent on the grain size.展开更多
The creep anisotropy behavior under different stresses at 180℃ of hot-extruded AZ91−2Y magnesium alloy with pre-compression(PC)and without pre-compression(NPC)was studied.Microstructure,texture and mechanical propert...The creep anisotropy behavior under different stresses at 180℃ of hot-extruded AZ91−2Y magnesium alloy with pre-compression(PC)and without pre-compression(NPC)was studied.Microstructure,texture and mechanical properties of the alloy were examined by scanning electron microscopy(SEM),electron backscatter diffraction(EBSD),transmission electron microscopy(TEM)and tensile creep tests.The results revealed that the creep resistance was proportional to the volume fraction of spherical Mg_(17)Al_(12) precipitates.The dynamic precipitation of large volume fraction of lamellar Mg_(17)Al_(12) in NPC samples leads to the basaláañslip as the dominant creep mechanism,and the NPC samples have obvious anisotropy.In the PC samples,dynamic precipitation of large volume fraction of spherical Mg_(17)Al_(12) has inhibitory effect on the basaláañslip.The pyramidalác+añslip and twinning improve the creep anisotropy resistance significantly.展开更多
As the total pressure ratio of centrifugal compressors increases, the diffuser inlet flow becomes highly subsonic or even supersonic, which causes additional shock loss. The shock loss leads the stage performance to d...As the total pressure ratio of centrifugal compressors increases, the diffuser inlet flow becomes highly subsonic or even supersonic, which causes additional shock loss. The shock loss leads the stage performance to drop greatly. Pre-compression is an efficient method for reducing shock loss and improving the stage performance. To study the effect of wedge diffusers with pre-compression blades on centrifugal compressor performance, wedge diffusers with various pre-compression angles, divergence angles and numbers of blades were designed and investigated via a numerical method. As a result, it is found that the compressor stage achieves high peak efficiency when the pre-compression angle ranges from 2.5° to 5.5° and when the divergence angle ranges from 7° to 9°. As the number of blades increases, the total pressure ratio and adiabatic efficiency of the compressor stage increase slightly, whereas the surge margin of the stage decreases.展开更多
To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under ...To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under different states. The spallation signals of these pre-compressed samples are measured by VISAR in the light-gas gun shock experiments. The experimental results show that even under the same impact velocity, the pullback amplitudes of the velocity at the free surface of the sam- pies vary significantly. According to the experimental data, we propose a distinct concept that the material spallation strength is closely related to the deviatoric stress fields in the material. Based on the numerical simulation, we develop a damage con- stitutive model, which reveals that the deviatoric stress reduces the tensile threshold of the void growth. The numerical inves- tigations also demonstrate that the spallation strength decreases as pre-compression increases. The experimental idea proposed in this paper can also be used to study the spallation process in other structures.展开更多
A combined experimental and computational study was carried out to investigate ballistic performance of laterally preload compressed SiC tile against long rod impact. A 100 x 100 by 20 mm thick SiC tile was pushed int...A combined experimental and computational study was carried out to investigate ballistic performance of laterally preload compressed SiC tile against long rod impact. A 100 x 100 by 20 mm thick SiC tile was pushed into a 5 mm thick steel frame at high temperature of 430 ℃ so that after cool down to room temperature, the lateral preload compressive stress was developed in the SiC tiles. Depth of penetration tests of the SiC tiles with and without pre-stress were performed, where tungsten alloy long rods at a nominal velocity of 1240 m/s were launched to hit the SiC tiles backed by the steel blocks. Compared with the SiC tiles without any pre-stress, the pre-compressed SiC tiles were found to reduce significantly the residual penetration in the backing block. Simulations were carried out using the LS-dyna hydrocode,taking account of preload stress. The simulations showed that the lateral preload compression strengthened the intact SiC tiles and dwell occurred in the early penetration stage, eroding the striking long rod efficiently.展开更多
Pre-compression and heat treatment were performed on an extruded AZ31 Mg alloy,and their effects on subsequent deformation behavior were investigated.The results show that at low temperature annealing(170 ℃ for 4 h),...Pre-compression and heat treatment were performed on an extruded AZ31 Mg alloy,and their effects on subsequent deformation behavior were investigated.The results show that at low temperature annealing(170 ℃ for 4 h),the extruded samples with and without annealing exhibit a nearly equivalent yield stress(~148 MPa) because their microstructures are nearly unchanged.However,under the same annealing condition,the yield stress of sample with pre-twinning and subsequent annealing(~225 MPa) is higher than that of the pre-twinned one(~200 MPa).The former sample presents a hardening effect because the solute atoms segregated on twin boundaries lead to a strengthening effect.The pre-twinned sample annealed at 400 ℃ for 1 h shows a higher ultimate elongation(~28%) than the pre-twinned one(~15%),but its yield stress(~125 MPa) is much lower than that of the pre-twinned one(~200 MPa).展开更多
A significant enhancement of bendability was achieved by the introduction of bimodal microstructure for AZ31B alloy sheets via pre-compression and subsequent annealing(PCA)process.This combined treatment led to the c-...A significant enhancement of bendability was achieved by the introduction of bimodal microstructure for AZ31B alloy sheets via pre-compression and subsequent annealing(PCA)process.This combined treatment led to the c-axis of the extracted samples that were inclined by 30°to the rolling direction(30°sample)further shifting toward the rolling direction(RD)and resulting in a higher Schmid factor(SF)value of basal slip under the RD tensile stress.Furthermore,the bimodal microstructure that was introduced by the PCA process broke the damage bands(DBs)in the initial hot rolled AZ31B alloy sheets and gave rise to a more uniform strain distribution in the outer tension region of the bending samples,in which the tensile deformation was accommodated by the equally distributed{101^(-)2}tension twinning and basal slip.Consequently,the bimodal microstructure,shifted basal texture and the modification of DBs were responsible for the significant enhancement in the bendability of the AZ31 alloys.展开更多
The effects of indentation loading depth and dynamic pre-compression on the creep behavior of CoCrFeNiAl_(0.3) high-entropy alloy(HEA)were studied through a series of indentation creep tests.Results show that the cree...The effects of indentation loading depth and dynamic pre-compression on the creep behavior of CoCrFeNiAl_(0.3) high-entropy alloy(HEA)were studied through a series of indentation creep tests.Results show that the creep displacement,creep stress exponent and creep strain rate are all sensitive to loading depth.A phenomenological model based on the holding time and loading depth was established by studying the characteristic relation between the loading depth and the creep displacement of CoCrFeNiAl_(0.3) HEA.The phenomenological model was used to analyze the creep behavior of the alloy under dynamic pre-compression(i.e.,dynamic compressive deformation caused by Hopkinson bar impact).展开更多
This study focuses on the geometry and kinematics of the Sinnyeong Fault which is the most conspicuous fault among the WNW-trending Gaeum Fault System in the Gyeongsang Basin,SE Korea. The fault is traced for over ca....This study focuses on the geometry and kinematics of the Sinnyeong Fault which is the most conspicuous fault among the WNW-trending Gaeum Fault System in the Gyeongsang Basin,SE Korea. The fault is traced for over ca.70 kmand has a consistent WNW-trending strike with a nearly vertical dip. It has an asymmetric fault damage zone of several meters to several tens of meters in width and a several meter-thick fault core. Its main movement is interpreted as sinistral-reverse oblique-slip or sinistral strike-slip under NE-SW compressional stress regime, although it could have experienced other faultings with different senses before/after this movement. Cylindrical folds, having the NW-trending fold axes of low angle plunge, are only observed along the southern damage zone of the fault with a continuous narrow width of several tens of meters. It is thus interpreted that the formation of the folds and sinistral movement of the fault were almost contemporaneously generated due to the concentration of the regional NE-SW compressional stress along pre-existing WNW-trending faults or densely populated fracture zone in a relatively stable intraplate region.展开更多
The present paper is part of a research that is devetoped within the sustainable building design through the revisiting of the traditional construction materials. The results obtained show that the naturat stone, enha...The present paper is part of a research that is devetoped within the sustainable building design through the revisiting of the traditional construction materials. The results obtained show that the naturat stone, enhanced by technoLogicaL innovations, are often capable of providing excellent performance. Based on the tests, it was possible to verify and validate the hypothesis that the proposed new system of external vertical opaque enclosure consisting in a panel in dry-assembled and pre- compressed blocks of natural stone through reinforcing steel has good performances when used both in the case of new design and in the case of recovery of modern buildings, when the intervention is being addressed within of an overaLL building improvement regarding the security, sustainabiLity, functionality and image. This paper reports the first results obtained by the study of the feasibility of the envelope being tested, through the definition of alL the detaits of links with the existing building structure.展开更多
基金Project(52101167)supported by the National Natural Science Foundation of ChinaProject(2022JJ40604)supported by the Natural Science Foundation of Hunan Province,ChinaProject(2022ZZTS0538)supported by the Postgraduate Research Innovation Project of Central South University,China。
文摘The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected to both pre-compression and pre-aging exhibits the most refined and densest distribution of precipitates upon aging at 200℃,leading to the superior age-hardening performance observed in the alloy.Comparatively,the alloy that underwent only pre-aging displayed a greater number density of precipitates than its counterpart that was neither pre-compressed nor pre-aged when both were aged to their peak conditions at 200℃,indicating an enhanced age-hardening response in the pre-aged alloy.The precipitates in these three peak-aged alloys consist of Mg_(2)Sn and MgZn_(2)phases.The reason why the pre-aged alloy has a higher number density of precipitates than the directly aged alloy is that MgZn_(2)phase formed during pre-aging can serve as heterogeneous nucleation site for the formation of Mg_(2)Sn.The reason why the pre compression and pre-aged alloy has the highest number density of precipitates is that Mg_(3)Sn and MgZn_(2)phases formed during pre-aging,alongside lattice defects introduced during pre-compression,collectively act as effective heterogeneous nucleation sites for the formation of Mg_(2)Sn during the subsequent aging at 200℃.
基金Projects(51328101,51301142)supported by the National Natural Science Foundation of ChinaProject(2015JJ2206)supported by Hunan Provincial Natural Science Foundation of China
文摘The combined effects of isothermal annealing and pre-compression on the mechanical properties of Cu36Zr48Al8Ag8 bulk metallic glass （BMG） were investigated. The as-cast specimens were first annealed at 743 K for 10 min, and then pre-compressed under 800 MPa for 1, 3, 5 and 10 h, respectively. The results indicated that annealing resulted in the formation of nanocrystals with a diameter of -10 nm in the amorphous matrix and a drastic decrease of the free volume, leading to complete loss of the plasticity of the BMG. Applying pre-compression under a stress of 800 MPa for a proper duration （5 h） resumed part of the lost free volume in the BMG matrix and therefore partially recovered the plasticity. A very long period of pre-compression （10 h） decreased the free volume again, which was caused by the excessive crystal growth.
基金supported by National Key Technology R&D Program of the Eleventh Five-year Plan of China(Grant No.2011BAF09B03)National Natural Science Foundation of China(Grant No.51075360)
文摘Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difticult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic（including fluid compressibility and viscosity） and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13~, the PCV volume is 1.3 ~ I0-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13~. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/rain, 1 500 r/rain, the swash plate angle is ll~, 13~, 15~ and 17~, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.
基金the financial supports from National Natural Science Foundation of China (U1764253)National Natural Science Foundation of China (51901202) and National Natural Science Foundation of China (51901204)。
文摘In this work, pre-strain annealing strengthening(PSAS) effect was investigated in an extruded Mg-1.0Gd-1.5 Zn(wt.%) alloy with respect to different grain sizes. The evolution of microstructures was provided by scanning electron microscopy(SEM), electron backscattered diffraction(EBSD), transmission electron microscopy(TEM) and high-angle annular dark-field scanning transmission electron microscopy(HAADF-STEM) under the initial state, pre-compression, intermediate annealing and re-compression conditions. The obtained results showed a grain size-dependent PSAS effect in the alloy. The sample with larger grain sizes corresponded to a higher strengthening effect, which mainly resulted from a more remarkable hindrance for the growth of existing twins and a larger proportion of activation for the nucleation of new twins. This was closely associated with the increase of back stress and friction stress for twin boundary motion impeded by the larger restraint of dislocations, the higher stress field surrounding solutes and the more Zn segregation. In addition to twinning behavior, Guinier Preston(G.P.) zones on basaldislocations were found after intermediate annealing and provided an extra strengthening by inhibiting the motions of gilding pre-existing dislocations and newly formed ones, but it was independent on the grain size.
基金the National Natural Science Foundation of China(Nos.52075048,52171099 and 52105140)the Natural Science Foundation of Hunan Province,China(No.2021JJ40583)+2 种基金the Science and Technology Innovation Project of Hunan Province,China(No.2018RS3073)the Scientific Research Innovation Project for Graduate Student of Changsha University of Science&Technology,China(No.CX2021SS55)the Double First-class Scientific Research International Cooperation Project of Changsha University of Science and Technology,China(No.2019IC15).
文摘The creep anisotropy behavior under different stresses at 180℃ of hot-extruded AZ91−2Y magnesium alloy with pre-compression(PC)and without pre-compression(NPC)was studied.Microstructure,texture and mechanical properties of the alloy were examined by scanning electron microscopy(SEM),electron backscatter diffraction(EBSD),transmission electron microscopy(TEM)and tensile creep tests.The results revealed that the creep resistance was proportional to the volume fraction of spherical Mg_(17)Al_(12) precipitates.The dynamic precipitation of large volume fraction of lamellar Mg_(17)Al_(12) in NPC samples leads to the basaláañslip as the dominant creep mechanism,and the NPC samples have obvious anisotropy.In the PC samples,dynamic precipitation of large volume fraction of spherical Mg_(17)Al_(12) has inhibitory effect on the basaláañslip.The pyramidalác+añslip and twinning improve the creep anisotropy resistance significantly.
文摘As the total pressure ratio of centrifugal compressors increases, the diffuser inlet flow becomes highly subsonic or even supersonic, which causes additional shock loss. The shock loss leads the stage performance to drop greatly. Pre-compression is an efficient method for reducing shock loss and improving the stage performance. To study the effect of wedge diffusers with pre-compression blades on centrifugal compressor performance, wedge diffusers with various pre-compression angles, divergence angles and numbers of blades were designed and investigated via a numerical method. As a result, it is found that the compressor stage achieves high peak efficiency when the pre-compression angle ranges from 2.5° to 5.5° and when the divergence angle ranges from 7° to 9°. As the number of blades increases, the total pressure ratio and adiabatic efficiency of the compressor stage increase slightly, whereas the surge margin of the stage decreases.
基金supported by the National Natural Science Foundation of China (Grant No. 10772165)the CAEP Foundation for Basic Research (Grant No. 2005R0802)
文摘To pre-compress the disk-shaped LY12 samples along the radial direction can be done with the aid of overstress assembly by heating or by mechanical clamping, which can also generate the deviatoric stress fields under different states. The spallation signals of these pre-compressed samples are measured by VISAR in the light-gas gun shock experiments. The experimental results show that even under the same impact velocity, the pullback amplitudes of the velocity at the free surface of the sam- pies vary significantly. According to the experimental data, we propose a distinct concept that the material spallation strength is closely related to the deviatoric stress fields in the material. Based on the numerical simulation, we develop a damage con- stitutive model, which reveals that the deviatoric stress reduces the tensile threshold of the void growth. The numerical inves- tigations also demonstrate that the spallation strength decreases as pre-compression increases. The experimental idea proposed in this paper can also be used to study the spallation process in other structures.
文摘A combined experimental and computational study was carried out to investigate ballistic performance of laterally preload compressed SiC tile against long rod impact. A 100 x 100 by 20 mm thick SiC tile was pushed into a 5 mm thick steel frame at high temperature of 430 ℃ so that after cool down to room temperature, the lateral preload compressive stress was developed in the SiC tiles. Depth of penetration tests of the SiC tiles with and without pre-stress were performed, where tungsten alloy long rods at a nominal velocity of 1240 m/s were launched to hit the SiC tiles backed by the steel blocks. Compared with the SiC tiles without any pre-stress, the pre-compressed SiC tiles were found to reduce significantly the residual penetration in the backing block. Simulations were carried out using the LS-dyna hydrocode,taking account of preload stress. The simulations showed that the lateral preload compression strengthened the intact SiC tiles and dwell occurred in the early penetration stage, eroding the striking long rod efficiently.
基金Project(XDJK2013C106)supported by the Fundamental Research Funds for the Central Universities of ChinaProject(51201140)supported by the National Natural Science Foundation of China
文摘Pre-compression and heat treatment were performed on an extruded AZ31 Mg alloy,and their effects on subsequent deformation behavior were investigated.The results show that at low temperature annealing(170 ℃ for 4 h),the extruded samples with and without annealing exhibit a nearly equivalent yield stress(~148 MPa) because their microstructures are nearly unchanged.However,under the same annealing condition,the yield stress of sample with pre-twinning and subsequent annealing(~225 MPa) is higher than that of the pre-twinned one(~200 MPa).The former sample presents a hardening effect because the solute atoms segregated on twin boundaries lead to a strengthening effect.The pre-twinned sample annealed at 400 ℃ for 1 h shows a higher ultimate elongation(~28%) than the pre-twinned one(~15%),but its yield stress(~125 MPa) is much lower than that of the pre-twinned one(~200 MPa).
基金financial supports from the National Natural Science Foundation of China (Nos.U1764253,51971044,U1910213,52001037,and U207601)Qinghai Scientific&Technological Program (No.2018-GX-A1)Natural Science Foundation of Chongqing (No.c stc2019jcyj-msxmX 0234)
文摘A significant enhancement of bendability was achieved by the introduction of bimodal microstructure for AZ31B alloy sheets via pre-compression and subsequent annealing(PCA)process.This combined treatment led to the c-axis of the extracted samples that were inclined by 30°to the rolling direction(30°sample)further shifting toward the rolling direction(RD)and resulting in a higher Schmid factor(SF)value of basal slip under the RD tensile stress.Furthermore,the bimodal microstructure that was introduced by the PCA process broke the damage bands(DBs)in the initial hot rolled AZ31B alloy sheets and gave rise to a more uniform strain distribution in the outer tension region of the bending samples,in which the tensile deformation was accommodated by the equally distributed{101^(-)2}tension twinning and basal slip.Consequently,the bimodal microstructure,shifted basal texture and the modification of DBs were responsible for the significant enhancement in the bendability of the AZ31 alloys.
基金support from the China Postdoctoral Science Foundation(Grant No.2021M702605)National Natural Science Foundation of China(Grant Nos.12102287,12102289,11772217).
文摘The effects of indentation loading depth and dynamic pre-compression on the creep behavior of CoCrFeNiAl_(0.3) high-entropy alloy(HEA)were studied through a series of indentation creep tests.Results show that the creep displacement,creep stress exponent and creep strain rate are all sensitive to loading depth.A phenomenological model based on the holding time and loading depth was established by studying the characteristic relation between the loading depth and the creep displacement of CoCrFeNiAl_(0.3) HEA.The phenomenological model was used to analyze the creep behavior of the alloy under dynamic pre-compression(i.e.,dynamic compressive deformation caused by Hopkinson bar impact).
文摘This study focuses on the geometry and kinematics of the Sinnyeong Fault which is the most conspicuous fault among the WNW-trending Gaeum Fault System in the Gyeongsang Basin,SE Korea. The fault is traced for over ca.70 kmand has a consistent WNW-trending strike with a nearly vertical dip. It has an asymmetric fault damage zone of several meters to several tens of meters in width and a several meter-thick fault core. Its main movement is interpreted as sinistral-reverse oblique-slip or sinistral strike-slip under NE-SW compressional stress regime, although it could have experienced other faultings with different senses before/after this movement. Cylindrical folds, having the NW-trending fold axes of low angle plunge, are only observed along the southern damage zone of the fault with a continuous narrow width of several tens of meters. It is thus interpreted that the formation of the folds and sinistral movement of the fault were almost contemporaneously generated due to the concentration of the regional NE-SW compressional stress along pre-existing WNW-trending faults or densely populated fracture zone in a relatively stable intraplate region.
文摘The present paper is part of a research that is devetoped within the sustainable building design through the revisiting of the traditional construction materials. The results obtained show that the naturat stone, enhanced by technoLogicaL innovations, are often capable of providing excellent performance. Based on the tests, it was possible to verify and validate the hypothesis that the proposed new system of external vertical opaque enclosure consisting in a panel in dry-assembled and pre- compressed blocks of natural stone through reinforcing steel has good performances when used both in the case of new design and in the case of recovery of modern buildings, when the intervention is being addressed within of an overaLL building improvement regarding the security, sustainabiLity, functionality and image. This paper reports the first results obtained by the study of the feasibility of the envelope being tested, through the definition of alL the detaits of links with the existing building structure.
