This paper proposes a hybrid decoupled power flow method for balanced power distribution systems with distributed generation sources. The method formulates the power flow equations in active power and reactive power d...This paper proposes a hybrid decoupled power flow method for balanced power distribution systems with distributed generation sources. The method formulates the power flow equations in active power and reactive power decoupled form with polar coordinates. Second-order terms are included in the active power mismatch iteration, and constant Jacobian and Hessian matrices are used. A hybrid direct and indirect solution technique is used to achieve efficiency and robustness of the algorithm. Active power correction is solved by means of a sparse lower triangular and upper triangular （LU） decomposition algorithm with partial pivoting, and the reactive power correction is solved by means of restarted generalized minimal residual algorithm with an incomplete LU pre-conditioner. Typical distribution generation models and distribution load models are included. The impact of zero-impedance branches is explicitly modeled through reconfiguring of the adjacent branches with impedances. Numerical examples on a sample distribution system with widespread photovoltaic installations are given to demonstrate the effectiveness of the proposed method.展开更多
As an important process during the cement production,grate cooler plays significance roles on clinker cooling and waste heat recovery.In this paper,we measured experimentally the heat balance of the grate cooler,which...As an important process during the cement production,grate cooler plays significance roles on clinker cooling and waste heat recovery.In this paper,we measured experimentally the heat balance of the grate cooler,which provided initial operating parameters for optimization.Then,the grate cooler was simplified into a series-connected heat exchanger network by power flow method.Constructing the equivalent thermal resistance network provided the global constraints by Kirchhoff’s law.On this basis,with the objectives of the minimum entropy generation numbers caused by heat transfer and viscous dissipation,solving a multi-objective optimization model achieved the Pareto Front by genetic algorithm.Then selecting the scheme of the lowest fan power consumption obtained the optimal operating parameters of the grate cooler.The results showed that the total mass flow of the optimized scheme did not change significantly compared with the original scheme,but the fan power consumption was 25.44%lower,and the heat recovery efficiency was 88.43%,which was improved by 11.35%.Furthermore,the analysis showed that the optimal operating parameters were affected by the local heat load.After optimizing the diameter of clinker particles within the allowable industrial range,the clinker with particle diameter of 0.02 m had the optimal performance.展开更多
The effect of line voltage drop is considered larger on loads, especially on asynchronous motor, transformers and other non-linear load parameters in power system of large ships. A novel power flow method based on imp...The effect of line voltage drop is considered larger on loads, especially on asynchronous motor, transformers and other non-linear load parameters in power system of large ships. A novel power flow method based on improved node voltage method is proposed, and a typical ship power system, which has 2 power stations and 10 nodes, with closed-loop design but open-loop operation, is taken as an example. Simulation results show that the improved power flow calculation method has achieved higher accuracy and better convergence.展开更多
For a long time, because of the lack of investment capital and enough attentions, the overall constructions of rural power grid were far behind than the urban power grid in Chongqing Jiangbei Power Company. The low vo...For a long time, because of the lack of investment capital and enough attentions, the overall constructions of rural power grid were far behind than the urban power grid in Chongqing Jiangbei Power Company. The low voltage problems were highlighted in the rural power grid due to the characteristics of rural power grid. Using the distribution network flow calculation method, we evaluated the low voltage problems of the rural power grid which belongs to Chongqing Jiangbei Power Company. In addition, we collected the data of distribution transformers in electricity consumption peak period. Some practical management strategies were proposed by the analysis and evaluation of potential and appeared low voltage problems.展开更多
In a power system, power generation and load have frequency response characteristics, which randomly fluctuate with changes in operating status. This study investigates a probabilistic power flow method that considers...In a power system, power generation and load have frequency response characteristics, which randomly fluctuate with changes in operating status. This study investigates a probabilistic power flow method that considers the unit and load uncertainty of the static frequency characteristic. Firstly, a calculation model is established on the basis of the characteristics of the frequency modulation performance of the unit and load. Then a calculation method is developed using the concept of dynamic power flow in order to determine the probability distribution of the active power flow of each line under the occurrence of a fault in the system. In the method, Monte Carlo sampling with the semi-invariant method is applied for analysis and calculation. The IEEE-30-buses system is taken as an example to analyze the impact of different responses of units on the power flow distribution of various branches. The method discussed herein is compared with the Monte Carlo simulation method to verify its effectiveness.展开更多
A new concept, namely, the equivalent mobility matrix of coupling subsystem is proposed, and the corresponding threesubsystem coupling progressive approach is explored. With the new efficient approach presented, the c...A new concept, namely, the equivalent mobility matrix of coupling subsystem is proposed, and the corresponding threesubsystem coupling progressive approach is explored. With the new efficient approach presented, the complexity in dealing with a more complicated dynamic coupling system is greatly reduced. The new modeling method is then combined with the theory of power flow to investigate the dynamics of the overall non rigid isolation system from the viewpoint of energy. The interaction between the resilient machine of its main modes and the resonant behavior of the flexible foundation on power flow transmission is studied. Taking a machine tool mounted on a multi story working plant as an example, the dynamic characteristics of the machine foundation coupling system are analyzed, and their effects on power flow transmission are revealed under various service frequency bands. Some advisable control strategies and the design principle for machinery mounted on flexible structure are proposed.展开更多
This paper is a further study of two papers [1] and [2], which were related to Ill-Conditioned Load Flow Problems and were published by IEEE Trans. PAS. The authors of this paper have some different opinions, for exam...This paper is a further study of two papers [1] and [2], which were related to Ill-Conditioned Load Flow Problems and were published by IEEE Trans. PAS. The authors of this paper have some different opinions, for example, the 11-bus system is not an ill-conditioned system. In addition, a new approach to solve Load Flow Problems, E-ψtc, is introduced. It is an explicit method;solving linear equations is not needed. It can handle very tough and very large systems. The advantage of this method has been fully proved by two examples. The authors give this new method a detailed description of how to use it to solve Load Flow Problems and successfully apply it to the 43-bus and the 11-bus systems. The authors also propose a strategy to test the reliability, and by solving gradient equations, this new method can answer if the solution exists or not.展开更多
This paper presents in the first place, the state of art relating to the methods to solve optimal power flows (OPF) and its application in electrical microgrids. Afterwards, a mathematical algorithm based on the gradi...This paper presents in the first place, the state of art relating to the methods to solve optimal power flows (OPF) and its application in electrical microgrids. Afterwards, a mathematical algorithm based on the gradient method is proposed for the application of OPF in a low power microgrid, in order to improve the voltages profiles and consequently reduce the active power losses. Finally, the proposed algorithm is implemented in a low power microgrid to demonstrate the effectiveness of the method.展开更多
The erythrocyte and blood flowing in the blood vessel can be treated as the two-phase flow of the mixture of particles and a power-law fluid in a peristaltic tube.In the present work, the peristaltic transport of a po...The erythrocyte and blood flowing in the blood vessel can be treated as the two-phase flow of the mixture of particles and a power-law fluid in a peristaltic tube.In the present work, the peristaltic transport of a power-law fluid and the suspension of particles in a tube is investigated by a perturbation method using the long wavelength approximation. The influence of different parameters on the velocity profile and streamlines is explored. Results show that there is a deflection of the flow field when the power-law index n = 0.5 or 1.5 compared with the Newtonian fluid where the trapping zone is symmetric to a certain cross section. The flux rate and reflux of the material are identified,and the conditions under which the reflux appears are determined. Moreover, a reflux phenomenon occurs near the wall. The trapping zone is related to not only the tube geometry and the flow flux but also the fluid properties. Both the length and width of the trapping zone increase with an increase in θ or φ. The trapping zone is more difficult to produce in the shear-thinning fluid than the shear-thickening fluid.展开更多
Power flow analysis is a numerical way of study of behavior of flow of electric power in an interconnected system. In order to meet the growing demands of electrical energy in an optimum way, there is a need to upgrad...Power flow analysis is a numerical way of study of behavior of flow of electric power in an interconnected system. In order to meet the growing demands of electrical energy in an optimum way, there is a need to upgrade existing systems or to install new systems. Therefore, planning of new installations and determination of best operating conditions of existing systems need power flow analysis. In this way, cost/benefit ratio for both suppliers and customers is maintained. This research involves the design and power flow analysis of IEEE-14 bus system. Newton Raphson method is applied for better efficiency and reduced computational time. Simulation analysis is conducted in ETAP software because of its excessive used in real life systems.展开更多
The continuation power flow method combined with the Jacobi-Davidson method is presented to trace the critical eigenvalues for power system small signal stability analysis. The continuation power flow based on a predi...The continuation power flow method combined with the Jacobi-Davidson method is presented to trace the critical eigenvalues for power system small signal stability analysis. The continuation power flow based on a predictor- corrector technique is applied to evaluate a continuum of steady state power flow solutions as system parameters change;meanwhile, the critical eigenvalues are found by the Jacobi-Davidson method, and thereby the trajectories of the critical eigenvalues, Hopf bifurcation and saddle node bifurcation points can also be found by the proposed method. The numerical simulations are studied in the IEEE 30-bus test system.展开更多
With the rapid development of the wind generation,uncertainties of random wind and load bring some inevitable impacts on the security of power system. Once the uncertainty causes line power to exceed its limit, line o...With the rapid development of the wind generation,uncertainties of random wind and load bring some inevitable impacts on the security of power system. Once the uncertainty causes line power to exceed its limit, line overload will occur. The paper presents the risk control of transmission line overload for windintegrated power systems. Firstly, a risk control model of line overload is proposed considering the uncertainties of loads,generator outputs and wind powers. The generation cost and security level of system associated with overload can be optimally controlled. Then path following interior point method is employed to carry out the optimal control. Finally the simulation is made on the modified IEEE-30 bus system. Results show that the risk of line overload is effectively reduced through the optimization of control variables.展开更多
Improving vehicle transmission efficiency and reducing vehicle fuel consumption is currently one of the main objectives in the automotive field. Reducing gear churning power losses has significant influence on the dec...Improving vehicle transmission efficiency and reducing vehicle fuel consumption is currently one of the main objectives in the automotive field. Reducing gear churning power losses has significant influence on the decreasing vehicle fuel consumption. Based on the two phase flow theory, a 2D two-phase model of the simplified hypoid gear is established to predict the churning losses in different conditions, the VOF method is introduced to track the volume fraction of the free surface, a standard k-ε model is also built to calculate complex turbulence. The oil distributions at the different rotational speed, the different immersion depth and the different viscosity as well as the churning losses of the hypoid gear are obtained and discussed in detail. In general, the churning power losses increase with the increase of the speed, the immersion depth and the viscosity, while the rotational speed shows the greatest influence on the churning losses. It is hoped that this investigation will be helpful in automotive industry applications.展开更多
文摘This paper proposes a hybrid decoupled power flow method for balanced power distribution systems with distributed generation sources. The method formulates the power flow equations in active power and reactive power decoupled form with polar coordinates. Second-order terms are included in the active power mismatch iteration, and constant Jacobian and Hessian matrices are used. A hybrid direct and indirect solution technique is used to achieve efficiency and robustness of the algorithm. Active power correction is solved by means of a sparse lower triangular and upper triangular （LU） decomposition algorithm with partial pivoting, and the reactive power correction is solved by means of restarted generalized minimal residual algorithm with an incomplete LU pre-conditioner. Typical distribution generation models and distribution load models are included. The impact of zero-impedance branches is explicitly modeled through reconfiguring of the adjacent branches with impedances. Numerical examples on a sample distribution system with widespread photovoltaic installations are given to demonstrate the effectiveness of the proposed method.
基金supported by the Shandong Provincial Natural Science Foundation(Grant No.ZR2019QEE016)。
文摘As an important process during the cement production,grate cooler plays significance roles on clinker cooling and waste heat recovery.In this paper,we measured experimentally the heat balance of the grate cooler,which provided initial operating parameters for optimization.Then,the grate cooler was simplified into a series-connected heat exchanger network by power flow method.Constructing the equivalent thermal resistance network provided the global constraints by Kirchhoff’s law.On this basis,with the objectives of the minimum entropy generation numbers caused by heat transfer and viscous dissipation,solving a multi-objective optimization model achieved the Pareto Front by genetic algorithm.Then selecting the scheme of the lowest fan power consumption obtained the optimal operating parameters of the grate cooler.The results showed that the total mass flow of the optimized scheme did not change significantly compared with the original scheme,but the fan power consumption was 25.44%lower,and the heat recovery efficiency was 88.43%,which was improved by 11.35%.Furthermore,the analysis showed that the optimal operating parameters were affected by the local heat load.After optimizing the diameter of clinker particles within the allowable industrial range,the clinker with particle diameter of 0.02 m had the optimal performance.
基金Supported by the National Natural Science Foundation under Grant No. 60704004
文摘The effect of line voltage drop is considered larger on loads, especially on asynchronous motor, transformers and other non-linear load parameters in power system of large ships. A novel power flow method based on improved node voltage method is proposed, and a typical ship power system, which has 2 power stations and 10 nodes, with closed-loop design but open-loop operation, is taken as an example. Simulation results show that the improved power flow calculation method has achieved higher accuracy and better convergence.
文摘For a long time, because of the lack of investment capital and enough attentions, the overall constructions of rural power grid were far behind than the urban power grid in Chongqing Jiangbei Power Company. The low voltage problems were highlighted in the rural power grid due to the characteristics of rural power grid. Using the distribution network flow calculation method, we evaluated the low voltage problems of the rural power grid which belongs to Chongqing Jiangbei Power Company. In addition, we collected the data of distribution transformers in electricity consumption peak period. Some practical management strategies were proposed by the analysis and evaluation of potential and appeared low voltage problems.
基金Supported by the State Grid Scientific and Technological Project (Title: Research on Control Strategy with Fast Demand Response to Severe Power Shortage, SGJS0000DKJS1700263)
文摘In a power system, power generation and load have frequency response characteristics, which randomly fluctuate with changes in operating status. This study investigates a probabilistic power flow method that considers the unit and load uncertainty of the static frequency characteristic. Firstly, a calculation model is established on the basis of the characteristics of the frequency modulation performance of the unit and load. Then a calculation method is developed using the concept of dynamic power flow in order to determine the probability distribution of the active power flow of each line under the occurrence of a fault in the system. In the method, Monte Carlo sampling with the semi-invariant method is applied for analysis and calculation. The IEEE-30-buses system is taken as an example to analyze the impact of different responses of units on the power flow distribution of various branches. The method discussed herein is compared with the Monte Carlo simulation method to verify its effectiveness.
文摘A new concept, namely, the equivalent mobility matrix of coupling subsystem is proposed, and the corresponding threesubsystem coupling progressive approach is explored. With the new efficient approach presented, the complexity in dealing with a more complicated dynamic coupling system is greatly reduced. The new modeling method is then combined with the theory of power flow to investigate the dynamics of the overall non rigid isolation system from the viewpoint of energy. The interaction between the resilient machine of its main modes and the resonant behavior of the flexible foundation on power flow transmission is studied. Taking a machine tool mounted on a multi story working plant as an example, the dynamic characteristics of the machine foundation coupling system are analyzed, and their effects on power flow transmission are revealed under various service frequency bands. Some advisable control strategies and the design principle for machinery mounted on flexible structure are proposed.
文摘This paper is a further study of two papers [1] and [2], which were related to Ill-Conditioned Load Flow Problems and were published by IEEE Trans. PAS. The authors of this paper have some different opinions, for example, the 11-bus system is not an ill-conditioned system. In addition, a new approach to solve Load Flow Problems, E-ψtc, is introduced. It is an explicit method;solving linear equations is not needed. It can handle very tough and very large systems. The advantage of this method has been fully proved by two examples. The authors give this new method a detailed description of how to use it to solve Load Flow Problems and successfully apply it to the 43-bus and the 11-bus systems. The authors also propose a strategy to test the reliability, and by solving gradient equations, this new method can answer if the solution exists or not.
文摘This paper presents in the first place, the state of art relating to the methods to solve optimal power flows (OPF) and its application in electrical microgrids. Afterwards, a mathematical algorithm based on the gradient method is proposed for the application of OPF in a low power microgrid, in order to improve the voltages profiles and consequently reduce the active power losses. Finally, the proposed algorithm is implemented in a low power microgrid to demonstrate the effectiveness of the method.
基金supported by the Major Program of National Natural Science Foundation of China(Nos.11632016 and 91634103)
文摘The erythrocyte and blood flowing in the blood vessel can be treated as the two-phase flow of the mixture of particles and a power-law fluid in a peristaltic tube.In the present work, the peristaltic transport of a power-law fluid and the suspension of particles in a tube is investigated by a perturbation method using the long wavelength approximation. The influence of different parameters on the velocity profile and streamlines is explored. Results show that there is a deflection of the flow field when the power-law index n = 0.5 or 1.5 compared with the Newtonian fluid where the trapping zone is symmetric to a certain cross section. The flux rate and reflux of the material are identified,and the conditions under which the reflux appears are determined. Moreover, a reflux phenomenon occurs near the wall. The trapping zone is related to not only the tube geometry and the flow flux but also the fluid properties. Both the length and width of the trapping zone increase with an increase in θ or φ. The trapping zone is more difficult to produce in the shear-thinning fluid than the shear-thickening fluid.
文摘Power flow analysis is a numerical way of study of behavior of flow of electric power in an interconnected system. In order to meet the growing demands of electrical energy in an optimum way, there is a need to upgrade existing systems or to install new systems. Therefore, planning of new installations and determination of best operating conditions of existing systems need power flow analysis. In this way, cost/benefit ratio for both suppliers and customers is maintained. This research involves the design and power flow analysis of IEEE-14 bus system. Newton Raphson method is applied for better efficiency and reduced computational time. Simulation analysis is conducted in ETAP software because of its excessive used in real life systems.
文摘The continuation power flow method combined with the Jacobi-Davidson method is presented to trace the critical eigenvalues for power system small signal stability analysis. The continuation power flow based on a predictor- corrector technique is applied to evaluate a continuum of steady state power flow solutions as system parameters change;meanwhile, the critical eigenvalues are found by the Jacobi-Davidson method, and thereby the trajectories of the critical eigenvalues, Hopf bifurcation and saddle node bifurcation points can also be found by the proposed method. The numerical simulations are studied in the IEEE 30-bus test system.
基金National Natural Science Foundations of China(Nos.51007052,71201097)Natural Science Foundation of Shanghai,China(No.14ZR1415300)
文摘With the rapid development of the wind generation,uncertainties of random wind and load bring some inevitable impacts on the security of power system. Once the uncertainty causes line power to exceed its limit, line overload will occur. The paper presents the risk control of transmission line overload for windintegrated power systems. Firstly, a risk control model of line overload is proposed considering the uncertainties of loads,generator outputs and wind powers. The generation cost and security level of system associated with overload can be optimally controlled. Then path following interior point method is employed to carry out the optimal control. Finally the simulation is made on the modified IEEE-30 bus system. Results show that the risk of line overload is effectively reduced through the optimization of control variables.
文摘Improving vehicle transmission efficiency and reducing vehicle fuel consumption is currently one of the main objectives in the automotive field. Reducing gear churning power losses has significant influence on the decreasing vehicle fuel consumption. Based on the two phase flow theory, a 2D two-phase model of the simplified hypoid gear is established to predict the churning losses in different conditions, the VOF method is introduced to track the volume fraction of the free surface, a standard k-ε model is also built to calculate complex turbulence. The oil distributions at the different rotational speed, the different immersion depth and the different viscosity as well as the churning losses of the hypoid gear are obtained and discussed in detail. In general, the churning power losses increase with the increase of the speed, the immersion depth and the viscosity, while the rotational speed shows the greatest influence on the churning losses. It is hoped that this investigation will be helpful in automotive industry applications.
