Soy-protein isolate(SPI)was used to prepare non-isocyanate polyurethane(NIPU)thermosetting adhesives for wood panels by reacting it with dimethyl carbonate(DMC)and hexamethylene diamine.Both linear as well as branched...Soy-protein isolate(SPI)was used to prepare non-isocyanate polyurethane(NIPU)thermosetting adhesives for wood panels by reacting it with dimethyl carbonate(DMC)and hexamethylene diamine.Both linear as well as branched oligomers were obtained and identified,indicating how such oligomer structures could further cross-link to form a hardened network.Unusual structures were observed,namely carbamic acid-derived urethane linkages coupled with lactam structures.The curing of the adhesive was followed by thermomechanical analysis(TMA).It appeared to follow a two stages process:First,at a lower temperature(maximum 130℃),the growth of linear oligomers occurred,finally forming a physically entangled network.This appeared to collapse and disentangle,causing a decrease of MOE,as the temperature increases.This appears to be due to the ever more marked Brownian movements of the linear oligomer chains with the increase of the temperature.Second,chemical cross-linking of the chains appeared to ensue,forming a hardened network.This was shown by the thermomechanical analysis(TMA)showing two distinct MOE maxima peaks,one around 130℃ and the other around 220℃,with a very marked MOE decrease between the two.Plywood panels were prepared and bonded with the SPI-NIPU wood adhesive and the results obtained are presented.The adhesive appeared to pass comfortably the requirements for dry strength of relevant standards,showing to be suitable for interior grade plywood panels.It did not pass the requirements for wet tests.However,addition of 15%of glycerol diglycidyl ether improved the wet tests results but still not enough to satisfy the standards requirements.展开更多
A non-isocyanate-based polyurethane(NIPU)wood adhesive was produced from organosolv lignin,which is a bio-sourced raw material,available in large quantities and produced as a by-product of the paper industry.The formu...A non-isocyanate-based polyurethane(NIPU)wood adhesive was produced from organosolv lignin,which is a bio-sourced raw material,available in large quantities and produced as a by-product of the paper industry.The formulation of this new lignin-based NIPU adhesive,which is presented,was chemically characterised by Matrix-Assisted Laser Desorption Ionization Time of Flight(MALDI ToF)mass spectrometry and by Fourier Transform Infra-Red(FTIR)spectrometry analyses.The oligomers formed were determined and showed that the three species involved in the NIPU adhesive preparation were formed by the co-reaction of the three reagents used:lignin,dimethyl carbonate,and hexamethylene diamine.Linear and branched structures were both identi-fied.Mechanical properties of the adhesive were determined using the Automated Bonding Evaluation System(ABES)and internal bond(IB)strength test of the laboratory particleboard bonded with it.The adhesive has shown satisfactory mechanical properties after hot pressing at 230℃.Such a temperature is used industrially in the most modern particleboard factories,but since it is hardly feasible for more conventional wood bonding equipment,the reactivity of the NIPU adhesive was successfully increased with the addition of a small percentage of a silane coupling agent.With the addition of the silane,the proposed NIPU adhesive could also be used at a hot-pressing temperature lower than 200℃.展开更多
Non-isocyanate polyurethane(NIPU)foams from a commercial hydrolysable tannin extract,chestnut wood tannin extract,have been prepared to determine what chemical species and products are taking part in the reactions inv...Non-isocyanate polyurethane(NIPU)foams from a commercial hydrolysable tannin extract,chestnut wood tannin extract,have been prepared to determine what chemical species and products are taking part in the reactions involved.This method is based on two main steps:the reaction with dimethyl carbonate and the formation of urethane bonds by further reaction of the carbonated tannin with a diamine-like hexamethylene diamine.The hydroxyl groups on the tannin polyphenols and on the carbohydrates intimately linked with it and part of a hydrolysable tannin are the groups involved in these reactions.The carbohydrate skeleton of the hydrolysable tannin is also able to participate through its hydroxyl groups to the same two reactions rendering the whole molecular complex able to react to form NIPUs.The analysis by Matrix-Assisted Laser Desorption Ionization(MALDI-TOF)mass spectrometry and 13C Nuclear Magnetic Resonance(13C NMR)to further investigate the reaction mechanisms involved revealed the unsuspected complexity of chestnut hydrolysable tannin,with different fragments reacting in different manners forming a hardened network of considerable complexity.As the morphology and performance of these types of foams changes slightly with the change in the amount of glutaraldehyde and hexamine hardeners,the best performing foam formulation previously determined was scanned by SEM and analysed chemically for the structures formed.展开更多
Polyols are groups of organic compounds which contain carbon and are randomly linked to other atoms,especially carbon-carbon and carbon-hydrogen.These compounds are mainly used as reactants to make other polymers.Amon...Polyols are groups of organic compounds which contain carbon and are randomly linked to other atoms,especially carbon-carbon and carbon-hydrogen.These compounds are mainly used as reactants to make other polymers.Among biopolymers,lignin is regarded as the base of a new polymer in polyol construction.The present study aimed to investigate the effects of amine type(diethylenetriamine and ethylenediamine)on the modification of lignin-based polyols,so as to provide an alternative to petroleum polyols and,in turn,increase functional groups and reduce their harm to humans’health and the environment.To this aim,first,lignin was extracted from raw liquor.Next,the extracted lignin was reacted with diethylenetriamine(DETA)and ethylenediamine(EDA).Finally,the Mannich method was used for the reaction between amine lignin and propylene carbonate.The results of the Fourier Transform Infrared(FTIR)spectroscopy analysis showed that modification with DETA led to more structural change in lignin and peak 1100 indicates the presence of C–O bond related to urethane bonds in modified lignin.Moreover,adding propylene carbonate to aminated lignin did not result in much change in the results of the FTIR analysis.Additionally,urethane bonds can be seen in the results of GPC at 400℃–500℃.Furthermore,a slight decrease in thermal stability was observed in lignin modified with amine and propylene carbonate,compared to the raw lignin sample.展开更多
The synthesis of polyurethanes(PUs)from the reaction of low molecular weight poly(ethylene carbonate)diol(PECD)is rarely investigated.This work reports a novel PU with excellent mechanical properties from the solution...The synthesis of polyurethanes(PUs)from the reaction of low molecular weight poly(ethylene carbonate)diol(PECD)is rarely investigated.This work reports a novel PU with excellent mechanical properties from the solution polymerization of 4,4-diphenylmethane diisocyanate(MDI)with PECD that was derived from the copolymerization of carbon dioxide(CO_(2))and ethylene oxide(EO).The tensile strength,the elongation at break and 300%constant tensile strength of the PECD-PU were up to 66±2 MPa,880%±50%and 13 MPa,respectively,higher than the control PUs from the reaction of MDI with commercial polyethers or polyesters.The PECD-PU with high CO_(2) carbonate content exhibited good solvent resistance and chemical stability.Of importance,the mechanical properties and chemical resistance of PECD-PU were significantly enhanced with the increasing content of CO_(2),i.e.,the carbonate unit in PECD.This work provides comprehensive properties of PECD-derived PUs,indicating that PECD is a competitive precursor for the preparation of PU and has broad application prospects.展开更多
In ultraviolet cured-in-place-pipe(UV-CIPP)pipeline rehabilitation,resin performance critically determines repair effectiveness.Current UV-curable resins exhibit high volatile organic compound(VOC)emissions and inadeq...In ultraviolet cured-in-place-pipe(UV-CIPP)pipeline rehabilitation,resin performance critically determines repair effectiveness.Current UV-curable resins exhibit high volatile organic compound(VOC)emissions and inadequate post-cure toughness,which compromise fatigue resistance during service.To address these issues,we synthesized hydroxyl-terminated polyurethane acrylate prepolymers using diphenylmethane diisocyanate(MDI),polypropylene glycol(PPG),and hydroxyethyl methacrylate(HEMA).Fourier transform infrared spectroscopy(FTIR)confirmed successful prepolymer synthesis.We developed UV-curable resins by incorporating various crosslinking monomers and optimized the formulations through mechanical property analysis.Testing revealed that the polyurethane-acrylic UV-cured resin system combines polyurethane's mechanical excellence with acrylics'high UV-curing activity.The PPG200/MDI/HEMA formulation achieved superior performance,with a tensile strength of 55.31 MPa,an impact toughness of 22.7 kJ/m^(2),and a heat deflection temperature(HDT)of 132℃.The optimized system eliminates volatile components while maintaining high reactivity,addressing critical limitations in trenchless pipeline rehabilitation.The improved mechanical properties meet the operational demands of underground pipes,suggesting practical applicability in trenchless pipeline repair.展开更多
Background:The development of materials for cardiovascular surgery that would improve the effectiveness of surgical interventions remains an important task.Surgical intervention during the implantation of vascular pro...Background:The development of materials for cardiovascular surgery that would improve the effectiveness of surgical interventions remains an important task.Surgical intervention during the implantation of vascular prostheses and stents,and the body’s reaction to artificial materials,could lead to chronic inflammation,a local increase in the concentration of proinflammatory factors,and stimulation of unwanted tissue growth.The introduction of nonsteroidal anti-inflammatory drugs into implantable devices could be used to obtain vascular implants that do not induce inflammation and do not induce neointimal tissue outgrowth.Methods:The scaffolds were made by electrospinning from mixtures of polyurethane(PU)with diclofenac(DF).The kinetics of DF release from the scaffolds composed of 3%PU/10%HSA/3%DMSO/DF and 3%PU/DF were studied.The biocompatibility and anti-inflammatory effects of the obtained scaffolds on human gingival fibroblasts and umbilical vein endothelial cells were studied.Results:Both types of scaffolds are characterized by fast DF release.The viability of cells cultured on scaffolds is 2 times worse than that of cells cultured on plastic.The level of the proinflammatory cytokine IL-6 in the culture medium of cells cultured on DF-containing scaffolds was lower than that of cells cultured on scaffolds without DF.Conclusion:The introduction of DF into scaffolds minimizes the inflammation caused by cell reactions to an artificial material.展开更多
文摘Soy-protein isolate(SPI)was used to prepare non-isocyanate polyurethane(NIPU)thermosetting adhesives for wood panels by reacting it with dimethyl carbonate(DMC)and hexamethylene diamine.Both linear as well as branched oligomers were obtained and identified,indicating how such oligomer structures could further cross-link to form a hardened network.Unusual structures were observed,namely carbamic acid-derived urethane linkages coupled with lactam structures.The curing of the adhesive was followed by thermomechanical analysis(TMA).It appeared to follow a two stages process:First,at a lower temperature(maximum 130℃),the growth of linear oligomers occurred,finally forming a physically entangled network.This appeared to collapse and disentangle,causing a decrease of MOE,as the temperature increases.This appears to be due to the ever more marked Brownian movements of the linear oligomer chains with the increase of the temperature.Second,chemical cross-linking of the chains appeared to ensue,forming a hardened network.This was shown by the thermomechanical analysis(TMA)showing two distinct MOE maxima peaks,one around 130℃ and the other around 220℃,with a very marked MOE decrease between the two.Plywood panels were prepared and bonded with the SPI-NIPU wood adhesive and the results obtained are presented.The adhesive appeared to pass comfortably the requirements for dry strength of relevant standards,showing to be suitable for interior grade plywood panels.It did not pass the requirements for wet tests.However,addition of 15%of glycerol diglycidyl ether improved the wet tests results but still not enough to satisfy the standards requirements.
基金This research was financed by the ERA-CoBioTech project WooBAdh(Environmentally-friendly bioadhesives from renewable resources).The University of Ljubljana,Biotechnical Faculty was financed by the Slovenian Ministry of Education,Science and Sport and the Slovenian Research Agency within the framework of program P4-0015.The LERMAB was financed by the French Agence Nationale de la Recherche(ANR)as part of the laboratory of excellence(LABEX)ARBRE.
文摘A non-isocyanate-based polyurethane(NIPU)wood adhesive was produced from organosolv lignin,which is a bio-sourced raw material,available in large quantities and produced as a by-product of the paper industry.The formulation of this new lignin-based NIPU adhesive,which is presented,was chemically characterised by Matrix-Assisted Laser Desorption Ionization Time of Flight(MALDI ToF)mass spectrometry and by Fourier Transform Infra-Red(FTIR)spectrometry analyses.The oligomers formed were determined and showed that the three species involved in the NIPU adhesive preparation were formed by the co-reaction of the three reagents used:lignin,dimethyl carbonate,and hexamethylene diamine.Linear and branched structures were both identi-fied.Mechanical properties of the adhesive were determined using the Automated Bonding Evaluation System(ABES)and internal bond(IB)strength test of the laboratory particleboard bonded with it.The adhesive has shown satisfactory mechanical properties after hot pressing at 230℃.Such a temperature is used industrially in the most modern particleboard factories,but since it is hardly feasible for more conventional wood bonding equipment,the reactivity of the NIPU adhesive was successfully increased with the addition of a small percentage of a silane coupling agent.With the addition of the silane,the proposed NIPU adhesive could also be used at a hot-pressing temperature lower than 200℃.
文摘Non-isocyanate polyurethane(NIPU)foams from a commercial hydrolysable tannin extract,chestnut wood tannin extract,have been prepared to determine what chemical species and products are taking part in the reactions involved.This method is based on two main steps:the reaction with dimethyl carbonate and the formation of urethane bonds by further reaction of the carbonated tannin with a diamine-like hexamethylene diamine.The hydroxyl groups on the tannin polyphenols and on the carbohydrates intimately linked with it and part of a hydrolysable tannin are the groups involved in these reactions.The carbohydrate skeleton of the hydrolysable tannin is also able to participate through its hydroxyl groups to the same two reactions rendering the whole molecular complex able to react to form NIPUs.The analysis by Matrix-Assisted Laser Desorption Ionization(MALDI-TOF)mass spectrometry and 13C Nuclear Magnetic Resonance(13C NMR)to further investigate the reaction mechanisms involved revealed the unsuspected complexity of chestnut hydrolysable tannin,with different fragments reacting in different manners forming a hardened network of considerable complexity.As the morphology and performance of these types of foams changes slightly with the change in the amount of glutaraldehyde and hexamine hardeners,the best performing foam formulation previously determined was scanned by SEM and analysed chemically for the structures formed.
文摘Polyols are groups of organic compounds which contain carbon and are randomly linked to other atoms,especially carbon-carbon and carbon-hydrogen.These compounds are mainly used as reactants to make other polymers.Among biopolymers,lignin is regarded as the base of a new polymer in polyol construction.The present study aimed to investigate the effects of amine type(diethylenetriamine and ethylenediamine)on the modification of lignin-based polyols,so as to provide an alternative to petroleum polyols and,in turn,increase functional groups and reduce their harm to humans’health and the environment.To this aim,first,lignin was extracted from raw liquor.Next,the extracted lignin was reacted with diethylenetriamine(DETA)and ethylenediamine(EDA).Finally,the Mannich method was used for the reaction between amine lignin and propylene carbonate.The results of the Fourier Transform Infrared(FTIR)spectroscopy analysis showed that modification with DETA led to more structural change in lignin and peak 1100 indicates the presence of C–O bond related to urethane bonds in modified lignin.Moreover,adding propylene carbonate to aminated lignin did not result in much change in the results of the FTIR analysis.Additionally,urethane bonds can be seen in the results of GPC at 400℃–500℃.Furthermore,a slight decrease in thermal stability was observed in lignin modified with amine and propylene carbonate,compared to the raw lignin sample.
基金financially supported by the Maoming Science and Technology Bureau(No.2022DZXHT007)。
文摘The synthesis of polyurethanes(PUs)from the reaction of low molecular weight poly(ethylene carbonate)diol(PECD)is rarely investigated.This work reports a novel PU with excellent mechanical properties from the solution polymerization of 4,4-diphenylmethane diisocyanate(MDI)with PECD that was derived from the copolymerization of carbon dioxide(CO_(2))and ethylene oxide(EO).The tensile strength,the elongation at break and 300%constant tensile strength of the PECD-PU were up to 66±2 MPa,880%±50%and 13 MPa,respectively,higher than the control PUs from the reaction of MDI with commercial polyethers or polyesters.The PECD-PU with high CO_(2) carbonate content exhibited good solvent resistance and chemical stability.Of importance,the mechanical properties and chemical resistance of PECD-PU were significantly enhanced with the increasing content of CO_(2),i.e.,the carbonate unit in PECD.This work provides comprehensive properties of PECD-derived PUs,indicating that PECD is a competitive precursor for the preparation of PU and has broad application prospects.
基金Funded by the National Natural Science Foundation of China(No.52473077)China Three Gorges Corporation(No.202403190)。
文摘In ultraviolet cured-in-place-pipe(UV-CIPP)pipeline rehabilitation,resin performance critically determines repair effectiveness.Current UV-curable resins exhibit high volatile organic compound(VOC)emissions and inadequate post-cure toughness,which compromise fatigue resistance during service.To address these issues,we synthesized hydroxyl-terminated polyurethane acrylate prepolymers using diphenylmethane diisocyanate(MDI),polypropylene glycol(PPG),and hydroxyethyl methacrylate(HEMA).Fourier transform infrared spectroscopy(FTIR)confirmed successful prepolymer synthesis.We developed UV-curable resins by incorporating various crosslinking monomers and optimized the formulations through mechanical property analysis.Testing revealed that the polyurethane-acrylic UV-cured resin system combines polyurethane's mechanical excellence with acrylics'high UV-curing activity.The PPG200/MDI/HEMA formulation achieved superior performance,with a tensile strength of 55.31 MPa,an impact toughness of 22.7 kJ/m^(2),and a heat deflection temperature(HDT)of 132℃.The optimized system eliminates volatile components while maintaining high reactivity,addressing critical limitations in trenchless pipeline rehabilitation.The improved mechanical properties meet the operational demands of underground pipes,suggesting practical applicability in trenchless pipeline repair.
基金supported by the Russian state-funded project for ICBFM SB RAS(grant number 125012300656-5)。
文摘Background:The development of materials for cardiovascular surgery that would improve the effectiveness of surgical interventions remains an important task.Surgical intervention during the implantation of vascular prostheses and stents,and the body’s reaction to artificial materials,could lead to chronic inflammation,a local increase in the concentration of proinflammatory factors,and stimulation of unwanted tissue growth.The introduction of nonsteroidal anti-inflammatory drugs into implantable devices could be used to obtain vascular implants that do not induce inflammation and do not induce neointimal tissue outgrowth.Methods:The scaffolds were made by electrospinning from mixtures of polyurethane(PU)with diclofenac(DF).The kinetics of DF release from the scaffolds composed of 3%PU/10%HSA/3%DMSO/DF and 3%PU/DF were studied.The biocompatibility and anti-inflammatory effects of the obtained scaffolds on human gingival fibroblasts and umbilical vein endothelial cells were studied.Results:Both types of scaffolds are characterized by fast DF release.The viability of cells cultured on scaffolds is 2 times worse than that of cells cultured on plastic.The level of the proinflammatory cytokine IL-6 in the culture medium of cells cultured on DF-containing scaffolds was lower than that of cells cultured on scaffolds without DF.Conclusion:The introduction of DF into scaffolds minimizes the inflammation caused by cell reactions to an artificial material.
