In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components ...In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components in aircraft.The interfacial plastic flow behavior and bonding mechanism of this process were investigated by a developed coupling EulerianLagrangian numerical model using software ABAQUS and a novel thermo-physical simulation method with designed embedded hot compression specimen.In addition,the formation mechanism and control method of welding defects caused by uneven plastic flow were discussed.The results reveal that the plastic flow along oscillating direction of this process is even and sufficient.In the direction perpendicular to oscillation,thermo-plastic metals mainly flow downward along welding interface under coupling of shear stress and interfacial pressure,resulting in the interfacial plastic zone shown as an inverted“V”shape.The upward plastic flow in this direction is relatively weak,and only a small amount of flash is extruded from top of joint.Moreover,the wedge block and welding components at top of joint are always in un-steady friction stage,leading to nonuniform temperature field distribution and un-welded defects.According to the results of numerical simulation,high oscillating frequency combined with low pressure and small amplitude is considered as appropriate parameter selection scheme to improve the upward interfacial plastic flow at top of joint and suppress the un-welded defects.The results of thermo-physical simulation illustrate that continuous dynamic recrystallization(CDRX)induces the bonding of interface,accompanying by intense dislocation movement and creation of many low-angle grain boundaries.In the interfacial bonding area,grain orientation is random with relatively low texture density(5.0 mud)owing to CDRX.展开更多
Warm tensile tests for aluminum alloy 7022 sheet are held at different temperatures and strain rates. The range of temperature is 293-773 K and that of the strain rate is 0. 001-0.1 s^-1. The warm tensile properties,r...Warm tensile tests for aluminum alloy 7022 sheet are held at different temperatures and strain rates. The range of temperature is 293-773 K and that of the strain rate is 0. 001-0.1 s^-1. The warm tensile properties,relations among temperature,strain rate,and the flow stress are discussed. Constitutive equations under the warm tension are obtained based on revised Hooke law and Grosman equation. It is concluded that flow stress declines with the increase of the temperature and the decrease of the strain rates. The elongation percentage increases with the increase of the temperature and the decrease of strain rate.展开更多
In a large area of the east—central Asian continent there is a unified seismic network system composed of two families of large—seismic belts that intersect conjugately. Such a seismic network in the middle—upper c...In a large area of the east—central Asian continent there is a unified seismic network system composed of two families of large—seismic belts that intersect conjugately. Such a seismic network in the middle—upper crust is actually a response to the plastic flow network in the lower lithosphere including the lower crust and lithospheric mantle. The existence of the unified plastic flow system confirms that the driving force for intraplate tectonic deformation results mainly from the compression of the India plate, while the long-range transmission of the force is carried out chiefly by means of plastic flow. The plastic flow network has a control over the intraplate tectonic deformation.展开更多
An experimental analysis on the subsequent yield-surfaces evolution using multiple specimens is presented for a 45 steel after a prescribed pre-strain loading in three different directions respectively, and the yieldi...An experimental analysis on the subsequent yield-surfaces evolution using multiple specimens is presented for a 45 steel after a prescribed pre-strain loading in three different directions respectively, and the yielding is defined by a designated offsetting strain. The size of the subsequent yield surface is found smaller than the initial yield surface; the negative cross effects are observed in the normal loading direction, its shape is not a Mises circle but has a rather blunt nose in loading direction and flat in the opposite. These results strongly depend on the loading path and the prescribed offset plastic strain. The plastic flow direction to the subsequent yield surface is investigated, and it is found that the plastic flow direction deviates from the normal flow rule. The deviation differs from preloading case to preloading case. And the plastic flow direction would have a larger deviation from the normal of the yield surface, if the subsequent yield was defined by a smaller offset strain. Furthermore, the experiments are simulated using the Chaboche model, and the results show that it can rationally predict yield-surface only when yield is defined by a fairly large offset strain.展开更多
The plastic flow behavior of the rotating band material is investigated in this paper. The rotating band material is processed from H96 brass alloy, which is hardened to a much higher yield strength compared to the an...The plastic flow behavior of the rotating band material is investigated in this paper. The rotating band material is processed from H96 brass alloy, which is hardened to a much higher yield strength compared to the annealed one. The dynamically uniaxial compression behavior of the material is tested using the split Hopkinson pressure bar(SHPB) with temperature and strain rate ranging from 297 to 1073 K and500 to 3000 s^(-1), respectively, and a phenomenological plastic flow stress model is developed to describe the mechanical behavior of the material. The material is found to present noticeable temperature sensitivity and weak strain-rate sensitivity. The construction of the plastic flow stress model has two steps. Firstly, three univariate stress functions, taking plastic strain, plastic strain rate and temperature as independent variable, respectively, are proposed by fixing the other two variables. Then, as the three univariate functions describe the special cases of flow stress behavior under various conditions, the principle of stress compatibility is adopted to obtain the complete flow stress function. The numerical results show that the proposed plastic flow stress model is more suitable for the rotating band material than the existing well-known models.展开更多
The rotational tool is put forward, which is composed of the one-spiral-flute shoul- der and the rotational pin with screw. Using the turbulent model of the FLUENT software, material plastic flow behavior during the p...The rotational tool is put forward, which is composed of the one-spiral-flute shoul- der and the rotational pin with screw. Using the turbulent model of the FLUENT software, material plastic flow behavior during the process of friction stir welding of Ti6A14V alloy is researched by the numerical simulation method and then the effect of rotational tool geometry on material flow during the welding process is attained. The results show that the flow direction of the material near the rotational tool is mainly the same as the rotational direction of the tool while the material near tool flows more violently than the other regions. For the tapered rotational pin, the flow velocity of material inside the workpiece decreases with the increase of the distance away from the workpiece surface because of the change of pin diameter. For the rotational tool, the flute added to the shoulder and the screw added to the pin can greatly increase the flow velocity of material during the welding process while the peak value of the flow velocity of material appears on the flute or the screw. Moreover, the rotational tool with the one-spiral-flute shoulder is better than the tool with the concentric- circles-flute shoulder. Decreasing the width of pin screw and increasing the diameter of pin tip are both good for the increase of flow velocity.展开更多
The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercool...The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amorphous alloy. Thus, it is proposed that the flow behavior of the nanocrystalline/amorphous composite at 646 K is mainly controlled by the viscous flow of the remaining supercooled liquid.展开更多
Recent studies have shown that the size of microvoids has a significant effect on the void growth rate.The purpose of this paper is to explore whether the void size effect can influence the plastic flow localization i...Recent studies have shown that the size of microvoids has a significant effect on the void growth rate.The purpose of this paper is to explore whether the void size effect can influence the plastic flow localization in ductile materials.We have used the extended Gurson's dilatational plasticity theory,which accounts for the void size effect,to study the plastic flow localization in porous solids with long cylindrical voids.The localization model of Rice is adopted,in which the material inside the band may display a different response from that outside the band at the incipient plastic flow localization.The present study shows that it has little effect on the shear band angle.展开更多
It has not been a simple matter to obtain a sound extension of the classical J2 flow theory of plasticity that incorporates a dependence on plastic strain gradients and that is capable of capturing size-dependent beha...It has not been a simple matter to obtain a sound extension of the classical J2 flow theory of plasticity that incorporates a dependence on plastic strain gradients and that is capable of capturing size-dependent behaviour of metals at the micron scale. Two classes of basic extensions of classical J2 theory have been proposed： one with increments in higher order stresses related to increments of strain gradients and the other characterized by the higher order stresses themselves expressed in terms of increments of strain gradients. The theories proposed by Muhlhans and Aifantis in 1991 and Fleck and Hutchinson in 2001 are in the first class, and, as formulated, these do not always satisfy thermodynamic requirements on plastic dissipation. On the other hand, theories of the second class proposed by Gudmundson in 2004 and Gurtin and Anand in 2009 have the physical deficiency that the higher order stress quantities can change discontinuously for bodies subject to arbitrarily small load changes. The present paper lays out this background to the quest for a sound phenomenological extension of the rateindependent J2 flow theory of plasticity to include a de- pendence on gradients of plastic strain. A modification of the Fleck-Hutchinson formulation that ensures its thermo- dynamic integrity is presented and contrasted with a comparable formulation of the second class where in the higher or- der stresses are expressed in terms of the plastic strain rate. Both versions are constructed to reduce to the classical J2 flow theory of plasticity when the gradients can be neglected and to coincide with the simpler and more readily formulated J2 deformation theory of gradient plasticity for deformation histories characterized by proportional straining.展开更多
The physical-cover-oriented variational principle of nonlinear numerical manifold method (NNMM) for the analysis of plastical problems is put forward according to the displacement model and the characters of numerical...The physical-cover-oriented variational principle of nonlinear numerical manifold method (NNMM) for the analysis of plastical problems is put forward according to the displacement model and the characters of numerical manifold method (NMM). The theoretical calculating formulations and the controlling equation of NNMM are derived. As an example, the plate with a hole in the center is calculated and the results show that the solution precision and efficiency of NNMM are agreeable.展开更多
Samples of Mg-8.2Gd-3.8Y-1.1Zn-0.4Zr alloy with and without an intragranular lamellae-shaped long period stacking ordered(LPSO)phase were prepared through heat treatment and a series of hot compression tests on these ...Samples of Mg-8.2Gd-3.8Y-1.1Zn-0.4Zr alloy with and without an intragranular lamellae-shaped long period stacking ordered(LPSO)phase were prepared through heat treatment and a series of hot compression tests on these materials were conducted to examine and evaluate the influence of LPSO on the hot compressive deformation behavior and deformation mechanisms at a given alloy composition.The values of activation energy for plastic flow(Qc)of the solution treated(without LPSO phase)and annealed alloys(with intragranular LPSO phase)were larger than that for pure Mg,indicating that the presence of a high amount of rare earth(RE)elements and LPSO in the Mg matrix significantly increases Qc.The Qcvalue of the annealed alloy was larger than that of the solution treated alloy at all the strain levels(223.3 vs.195.5 k J/mol in average)and the largest difference in Qcbetween the two alloys was recorded at the smallest strain of 0.1 where precipitation of LPSO during deformation was limited in the solution treated alloy.These observations imply that the formation of LPSO phase out of the RE-rich solid solution matrix during deformation increases Qc,but the increment is not so large.Analysis of the hot compressive data of the alloys with LPSO phase and the alloys with RE-rich solid solution matrix in literatures indicates the similarity of the effect of the LPSO and RE-rich solid solution matrix phases on Qcand high-temperature strength.展开更多
Lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) and plate specimens (100 mm×100 mm×50 mm) were tested under biaxial compression-compression (CC) and compression-tension (CT) lo...Lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) and plate specimens (100 mm×100 mm×50 mm) were tested under biaxial compression-compression (CC) and compression-tension (CT) load combinations. For comparison, normal concrete plate specimens (100 mm×100 mm×50 mm) were tested under the same load combinations. Based on the test results, a two-level strength criterion of lightweight aggregate concrete in both octahedral stress coordinate and principal stress coordinate was suggested. The lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) were then tested under triaxial compression-compression-compression (CCC) load combination with corresponding tests on normal concrete cube specimens (100 mm×100 mm×100 mm). The effect of intermediate principal stress on triaxial compressive strength is further examined. A "plastic flow plateau" area was apparent in principal compressive stress-strain relationships of lightweight aggregate concrete but not in normal concrete. A quadratic formula was suggested for the expression of strength criterion under triaxial compression.展开更多
In this paper, we report a strain rate related glass transition in model SrCaYbMg（Li）Zn（Cu） metallic glasses at room temperature. A critical strain rate, equivalent to glass transition temperature, is found for th...In this paper, we report a strain rate related glass transition in model SrCaYbMg（Li）Zn（Cu） metallic glasses at room temperature. A critical strain rate, equivalent to glass transition temperature, is found for the strain rate induced glassy state to liquid-like viscoplastic state translation. The results show that the observation time, equivalent to temperature and stress, is a key parameter for the transition between the glass and supercooled liquid states. A three-dimension glass transition diagram involved in time, temperature and stress in metallic glasses is established.展开更多
Uniaxial or triaxial compression test of cylindrical rock specimens using rock mechanics testing machine is a basic experimental method to study the strength and deformation characteristics of rock and the development...Uniaxial or triaxial compression test of cylindrical rock specimens using rock mechanics testing machine is a basic experimental method to study the strength and deformation characteristics of rock and the development process of rock fracture. Extensive literature review has been conducted on this issue;meanwhile, experimental and numerical studies have been conducted on the stress-drop effect on the brittleness of rock materials. A plastic flow factor of λ is proposed to describe the stress-drop effect. Evaluation methods of the factor λ corresponding to the four yield criteria of rock mass are proposed. Those four yield criteria are Tresca criterion, von-Mises criterion, Mohr-Coulomb criterion and Drucker-Prager criterion. For simplicity purposes, an engineering approximation approach has been proposed to evaluate the stress-drop with a non-zero strain increment. Numerical simulation results validated the effectiveness of the plastic flow factors λ as well as the engineering approximation approach. Based on the results in this study, finite element code can be programmed for brittle materials with stress-drop, which has the potential to be readily incorporated in finite element codes.展开更多
In this work,the effects of Cr and Al contents on the preparation of SiC fiber-reinforced NiCrAl alloy matrix composites(SiCf/Ni-20Cr-5Al,SiCf/Ni-15Cr-5Al,SiCf/Ni-10Cr-5Al and SiCf/Ni-10Cr-3Al)were thoroughly discusse...In this work,the effects of Cr and Al contents on the preparation of SiC fiber-reinforced NiCrAl alloy matrix composites(SiCf/Ni-20Cr-5Al,SiCf/Ni-15Cr-5Al,SiCf/Ni-10Cr-5Al and SiCf/Ni-10Cr-3Al)were thoroughly discussed.The composites were prepared by vacuum hot pressing process using matrix-coated fibers.It was found that Cr solute atoms played a significant role in retarding the recrystallization of NiCrAl alloy matrix,and the Al elements in the form of γ'-Ni3Al phase had a suppression effect on the plastic flow of the matrix.Therefore,the reduction in Cr and Al contents was conductive to the recrystallization and plastic flow of NiCrAl alloy matrix,thereby reduced the size and number of micro-voids in the composite.In addition,this work provides some guidance for designing and manufacturing reasonable SiC fiber-reinforced Ni alloy matrix composites.展开更多
For friction stir welding （FSW）, a new idea is put forward in this paper to weld the thin plate of Al alloy by using the rotational tool without pin. The experiments of FSW are carried out by using the tools with in...For friction stir welding （FSW）, a new idea is put forward in this paper to weld the thin plate of Al alloy by using the rotational tool without pin. The experiments of FSW are carried out by using the tools with inner-concave-flute shoulder, concentric-circles-flute shoulder and three-spiral-flute shoulder, respectively. The experimental results show that the grain size in weld nugget zone attained by the tool with three-spiral-flute shoulder is nearly the same while the grain sizes decrease with the decrease of welding velocity. The displacement of material flow in the heat-mechanical affected zone by the tool with three-spiral-flute shoulder is much larger than that by the tool with inner-concave-flute shoulder or concentric-circles–flute shoulder. The above-mentioned results are verified by numerical simulation. For the tool with three-spiral-flute shoulder, the tensile strength of FSW joint increases with the decrease of welding velocity while the value of tensile strength attained by the welding velocity of 20 mm/min and the rotation speed of 1800 r/min is about 398 MPa, which is 80% more than that of parent mental tensile strength. Those verify that the tool with three-spiral-flute shoulder can be used to join the thin plate of Al alloy.展开更多
An experimental investigation was carried out on the flow characteristic and hardening of steel 40 subjected to complex combined axial-torsional cyclic straining. For a specific cyclic strain path, the steel has mainl...An experimental investigation was carried out on the flow characteristic and hardening of steel 40 subjected to complex combined axial-torsional cyclic straining. For a specific cyclic strain path, the steel has mainly cyclic softening behavior when the strain amplitude is small. While with an increase of the effective strain amplitude, the softening becomes small, but there is the cyclic softening even though the steel is subjected to the cyclic loading by a square strain path. However, the steel has cyclic additional hardening by a nonproportional path, compared with the proportional cycling. Generally, the additional hardening is small and its historical effect is not obvious at small strain amplitude. The additional hardening is remarkable by a cross-triangular strain path of large strain amplitude. The memory of the history of nonproportional cyclic loading, the direction of plastic flow and the plastic modulus of the steel were also studied.展开更多
The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile ...The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile metal and the dispersive phase is assumed to consist of either aligned or randomly-oriented, elastic,, spheroidal inhomogeneities. The plastic flow and decreasing stiffness of the matrix during Eshelby's transformation strain of the equivalent inclusions are accounted for by using the deformation theory of plasticity. The explicit results of the instantaneous overall thermal expansion coefficients and the critical inelastic temperature changes are presented for aligned disc- and fiber-inclusions. For the spherical and randomly-oriented spheroidal inclusion, the present study demonstrates that when the yielding of the composites is governed by the average matrix stress, the overall response is always elastic in spite of the temperature change.展开更多
Langevin simulations are preformed on the depinning dynamics of fluid monolayer on a quenched substrate. With increase in the strength of the substrate, we find for the first time a crossover from elastic crystal to s...Langevin simulations are preformed on the depinning dynamics of fluid monolayer on a quenched substrate. With increase in the strength of the substrate, we find for the first time a crossover from elastic crystal to smectic flows as well as a crossover from smectic to plastic flows above the depinning. A power-law scaling relationship can be derived between the drift velocity and the driving force for both the elastic crystal and smectic flows, but fails to be obtained for the plastic flow. The power-law exponents are found to be no larger than 1 for the elastic crystal flow and larger than 1 for the smeetic flow. The critical driving force and the averaged intensity of Bragg peaks remain invariant basically in the regime of smectic flow. A sudden increase in the critical driving force is observed within the crossover from the smeetic to plastic flows, and the averaged intensity of Bragg peaks shows sudden decreases within the crossovers both from the elastic crystal to smectic flows and from the smectic to plastic flows. The results are helpful for understanding the slip dynamics of fluids on a molecular level.展开更多
This paper reviews the recent progress in the studies of experimental rock mechanics and tectonophysics concerning seismology and physics of the Earths interior in China. The progress is presented in the following asp...This paper reviews the recent progress in the studies of experimental rock mechanics and tectonophysics concerning seismology and physics of the Earths interior in China. The progress is presented in the following aspects: a) A lot of results of experiment and numerical simulation enrich our knowledge of the brittle fracturing process under the condition with heterogeneity in material and structure; b) Some new results on frictional behavior of non-homogeneous faults reveal the complexity of faulting behavior; c) Some new results on the brittle-plastic transition and plastic flow are obtained; especially the important progress is obtained on rheological properties of rocks in the lower crust and the upper mantle; d) A lot of experimental results are obtained on rock physics at high temperature and pressure and have been used in study of material composition and state. These results provide useful information for understanding the physical properties and deformation mechanisms of material of the Earths interior and earthquake physics.展开更多
基金co-supported by the National Natural Science Foundation of China(Nos.52105411,52105400and 52305420)the China Postdoctoral Science Foundation(No.2023M742830)Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University(No.CX2023008).
文摘In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components in aircraft.The interfacial plastic flow behavior and bonding mechanism of this process were investigated by a developed coupling EulerianLagrangian numerical model using software ABAQUS and a novel thermo-physical simulation method with designed embedded hot compression specimen.In addition,the formation mechanism and control method of welding defects caused by uneven plastic flow were discussed.The results reveal that the plastic flow along oscillating direction of this process is even and sufficient.In the direction perpendicular to oscillation,thermo-plastic metals mainly flow downward along welding interface under coupling of shear stress and interfacial pressure,resulting in the interfacial plastic zone shown as an inverted“V”shape.The upward plastic flow in this direction is relatively weak,and only a small amount of flash is extruded from top of joint.Moreover,the wedge block and welding components at top of joint are always in un-steady friction stage,leading to nonuniform temperature field distribution and un-welded defects.According to the results of numerical simulation,high oscillating frequency combined with low pressure and small amplitude is considered as appropriate parameter selection scheme to improve the upward interfacial plastic flow at top of joint and suppress the un-welded defects.The results of thermo-physical simulation illustrate that continuous dynamic recrystallization(CDRX)induces the bonding of interface,accompanying by intense dislocation movement and creation of many low-angle grain boundaries.In the interfacial bonding area,grain orientation is random with relatively low texture density(5.0 mud)owing to CDRX.
基金Supported by the National Natural Science Foundation of China (50772095)the Graduate Innovation Foundation of Jiangsu Province (CX09B-073Z)~~
文摘Warm tensile tests for aluminum alloy 7022 sheet are held at different temperatures and strain rates. The range of temperature is 293-773 K and that of the strain rate is 0. 001-0.1 s^-1. The warm tensile properties,relations among temperature,strain rate,and the flow stress are discussed. Constitutive equations under the warm tension are obtained based on revised Hooke law and Grosman equation. It is concluded that flow stress declines with the increase of the temperature and the decrease of the strain rates. The elongation percentage increases with the increase of the temperature and the decrease of strain rate.
基金This project (No. 49070196) is funded by the National Science Foundation of China.
文摘In a large area of the east—central Asian continent there is a unified seismic network system composed of two families of large—seismic belts that intersect conjugately. Such a seismic network in the middle—upper crust is actually a response to the plastic flow network in the lower lithosphere including the lower crust and lithospheric mantle. The existence of the unified plastic flow system confirms that the driving force for intraplate tectonic deformation results mainly from the compression of the India plate, while the long-range transmission of the force is carried out chiefly by means of plastic flow. The plastic flow network has a control over the intraplate tectonic deformation.
基金Project supported by the National Natural Science Foundation of China(Nos.90815001and11072064)Key Project of Guangxi Science and Technology Lab Center(No.LGZX201101)
文摘An experimental analysis on the subsequent yield-surfaces evolution using multiple specimens is presented for a 45 steel after a prescribed pre-strain loading in three different directions respectively, and the yielding is defined by a designated offsetting strain. The size of the subsequent yield surface is found smaller than the initial yield surface; the negative cross effects are observed in the normal loading direction, its shape is not a Mises circle but has a rather blunt nose in loading direction and flat in the opposite. These results strongly depend on the loading path and the prescribed offset plastic strain. The plastic flow direction to the subsequent yield surface is investigated, and it is found that the plastic flow direction deviates from the normal flow rule. The deviation differs from preloading case to preloading case. And the plastic flow direction would have a larger deviation from the normal of the yield surface, if the subsequent yield was defined by a smaller offset strain. Furthermore, the experiments are simulated using the Chaboche model, and the results show that it can rationally predict yield-surface only when yield is defined by a fairly large offset strain.
基金the support from National Natural Science Foundation of China (Grant Nos. 11702137 and U2141246)。
文摘The plastic flow behavior of the rotating band material is investigated in this paper. The rotating band material is processed from H96 brass alloy, which is hardened to a much higher yield strength compared to the annealed one. The dynamically uniaxial compression behavior of the material is tested using the split Hopkinson pressure bar(SHPB) with temperature and strain rate ranging from 297 to 1073 K and500 to 3000 s^(-1), respectively, and a phenomenological plastic flow stress model is developed to describe the mechanical behavior of the material. The material is found to present noticeable temperature sensitivity and weak strain-rate sensitivity. The construction of the plastic flow stress model has two steps. Firstly, three univariate stress functions, taking plastic strain, plastic strain rate and temperature as independent variable, respectively, are proposed by fixing the other two variables. Then, as the three univariate functions describe the special cases of flow stress behavior under various conditions, the principle of stress compatibility is adopted to obtain the complete flow stress function. The numerical results show that the proposed plastic flow stress model is more suitable for the rotating band material than the existing well-known models.
基金supported by the National Natural Science Foundation of China(No. 61074090)
文摘The rotational tool is put forward, which is composed of the one-spiral-flute shoul- der and the rotational pin with screw. Using the turbulent model of the FLUENT software, material plastic flow behavior during the process of friction stir welding of Ti6A14V alloy is researched by the numerical simulation method and then the effect of rotational tool geometry on material flow during the welding process is attained. The results show that the flow direction of the material near the rotational tool is mainly the same as the rotational direction of the tool while the material near tool flows more violently than the other regions. For the tapered rotational pin, the flow velocity of material inside the workpiece decreases with the increase of the distance away from the workpiece surface because of the change of pin diameter. For the rotational tool, the flute added to the shoulder and the screw added to the pin can greatly increase the flow velocity of material during the welding process while the peak value of the flow velocity of material appears on the flute or the screw. Moreover, the rotational tool with the one-spiral-flute shoulder is better than the tool with the concentric- circles-flute shoulder. Decreasing the width of pin screw and increasing the diameter of pin tip are both good for the increase of flow velocity.
文摘The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amorphous alloy. Thus, it is proposed that the flow behavior of the nanocrystalline/amorphous composite at 646 K is mainly controlled by the viscous flow of the remaining supercooled liquid.
基金The project supported by the National Natural Science Foundation of China (10121202) and Ministry of Education,China (20020003023 and Key Grant Project 0306)
文摘Recent studies have shown that the size of microvoids has a significant effect on the void growth rate.The purpose of this paper is to explore whether the void size effect can influence the plastic flow localization in ductile materials.We have used the extended Gurson's dilatational plasticity theory,which accounts for the void size effect,to study the plastic flow localization in porous solids with long cylindrical voids.The localization model of Rice is adopted,in which the material inside the band may display a different response from that outside the band at the incipient plastic flow localization.The present study shows that it has little effect on the shear band angle.
文摘It has not been a simple matter to obtain a sound extension of the classical J2 flow theory of plasticity that incorporates a dependence on plastic strain gradients and that is capable of capturing size-dependent behaviour of metals at the micron scale. Two classes of basic extensions of classical J2 theory have been proposed： one with increments in higher order stresses related to increments of strain gradients and the other characterized by the higher order stresses themselves expressed in terms of increments of strain gradients. The theories proposed by Muhlhans and Aifantis in 1991 and Fleck and Hutchinson in 2001 are in the first class, and, as formulated, these do not always satisfy thermodynamic requirements on plastic dissipation. On the other hand, theories of the second class proposed by Gudmundson in 2004 and Gurtin and Anand in 2009 have the physical deficiency that the higher order stress quantities can change discontinuously for bodies subject to arbitrarily small load changes. The present paper lays out this background to the quest for a sound phenomenological extension of the rateindependent J2 flow theory of plasticity to include a de- pendence on gradients of plastic strain. A modification of the Fleck-Hutchinson formulation that ensures its thermo- dynamic integrity is presented and contrasted with a comparable formulation of the second class where in the higher or- der stresses are expressed in terms of the plastic strain rate. Both versions are constructed to reduce to the classical J2 flow theory of plasticity when the gradients can be neglected and to coincide with the simpler and more readily formulated J2 deformation theory of gradient plasticity for deformation histories characterized by proportional straining.
文摘The physical-cover-oriented variational principle of nonlinear numerical manifold method (NNMM) for the analysis of plastical problems is put forward according to the displacement model and the characters of numerical manifold method (NMM). The theoretical calculating formulations and the controlling equation of NNMM are derived. As an example, the plate with a hole in the center is calculated and the results show that the solution precision and efficiency of NNMM are agreeable.
基金financially supported by the Mid-Career Researcher Program through the National Research Foundation of Korea funded by the Ministry of Education,Science and Technology(NRF-2020R1A2C1008105)。
文摘Samples of Mg-8.2Gd-3.8Y-1.1Zn-0.4Zr alloy with and without an intragranular lamellae-shaped long period stacking ordered(LPSO)phase were prepared through heat treatment and a series of hot compression tests on these materials were conducted to examine and evaluate the influence of LPSO on the hot compressive deformation behavior and deformation mechanisms at a given alloy composition.The values of activation energy for plastic flow(Qc)of the solution treated(without LPSO phase)and annealed alloys(with intragranular LPSO phase)were larger than that for pure Mg,indicating that the presence of a high amount of rare earth(RE)elements and LPSO in the Mg matrix significantly increases Qc.The Qcvalue of the annealed alloy was larger than that of the solution treated alloy at all the strain levels(223.3 vs.195.5 k J/mol in average)and the largest difference in Qcbetween the two alloys was recorded at the smallest strain of 0.1 where precipitation of LPSO during deformation was limited in the solution treated alloy.These observations imply that the formation of LPSO phase out of the RE-rich solid solution matrix during deformation increases Qc,but the increment is not so large.Analysis of the hot compressive data of the alloys with LPSO phase and the alloys with RE-rich solid solution matrix in literatures indicates the similarity of the effect of the LPSO and RE-rich solid solution matrix phases on Qcand high-temperature strength.
基金Project (No. 50679007) supported by the National Natural Science Foundation of China
文摘Lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) and plate specimens (100 mm×100 mm×50 mm) were tested under biaxial compression-compression (CC) and compression-tension (CT) load combinations. For comparison, normal concrete plate specimens (100 mm×100 mm×50 mm) were tested under the same load combinations. Based on the test results, a two-level strength criterion of lightweight aggregate concrete in both octahedral stress coordinate and principal stress coordinate was suggested. The lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) were then tested under triaxial compression-compression-compression (CCC) load combination with corresponding tests on normal concrete cube specimens (100 mm×100 mm×100 mm). The effect of intermediate principal stress on triaxial compressive strength is further examined. A "plastic flow plateau" area was apparent in principal compressive stress-strain relationships of lightweight aggregate concrete but not in normal concrete. A quadratic formula was suggested for the expression of strength criterion under triaxial compression.
基金supported by the National Natural Science Foundation of China (No. 51271195)
文摘In this paper, we report a strain rate related glass transition in model SrCaYbMg（Li）Zn（Cu） metallic glasses at room temperature. A critical strain rate, equivalent to glass transition temperature, is found for the strain rate induced glassy state to liquid-like viscoplastic state translation. The results show that the observation time, equivalent to temperature and stress, is a key parameter for the transition between the glass and supercooled liquid states. A three-dimension glass transition diagram involved in time, temperature and stress in metallic glasses is established.
基金Projects(51678083,41302226)supported by the National Natural Science Foundation of China
文摘Uniaxial or triaxial compression test of cylindrical rock specimens using rock mechanics testing machine is a basic experimental method to study the strength and deformation characteristics of rock and the development process of rock fracture. Extensive literature review has been conducted on this issue;meanwhile, experimental and numerical studies have been conducted on the stress-drop effect on the brittleness of rock materials. A plastic flow factor of λ is proposed to describe the stress-drop effect. Evaluation methods of the factor λ corresponding to the four yield criteria of rock mass are proposed. Those four yield criteria are Tresca criterion, von-Mises criterion, Mohr-Coulomb criterion and Drucker-Prager criterion. For simplicity purposes, an engineering approximation approach has been proposed to evaluate the stress-drop with a non-zero strain increment. Numerical simulation results validated the effectiveness of the plastic flow factors λ as well as the engineering approximation approach. Based on the results in this study, finite element code can be programmed for brittle materials with stress-drop, which has the potential to be readily incorporated in finite element codes.
基金financially supported by the National Natural Science Foundation of China(No.51371170)。
文摘In this work,the effects of Cr and Al contents on the preparation of SiC fiber-reinforced NiCrAl alloy matrix composites(SiCf/Ni-20Cr-5Al,SiCf/Ni-15Cr-5Al,SiCf/Ni-10Cr-5Al and SiCf/Ni-10Cr-3Al)were thoroughly discussed.The composites were prepared by vacuum hot pressing process using matrix-coated fibers.It was found that Cr solute atoms played a significant role in retarding the recrystallization of NiCrAl alloy matrix,and the Al elements in the form of γ'-Ni3Al phase had a suppression effect on the plastic flow of the matrix.Therefore,the reduction in Cr and Al contents was conductive to the recrystallization and plastic flow of NiCrAl alloy matrix,thereby reduced the size and number of micro-voids in the composite.In addition,this work provides some guidance for designing and manufacturing reasonable SiC fiber-reinforced Ni alloy matrix composites.
文摘For friction stir welding （FSW）, a new idea is put forward in this paper to weld the thin plate of Al alloy by using the rotational tool without pin. The experiments of FSW are carried out by using the tools with inner-concave-flute shoulder, concentric-circles-flute shoulder and three-spiral-flute shoulder, respectively. The experimental results show that the grain size in weld nugget zone attained by the tool with three-spiral-flute shoulder is nearly the same while the grain sizes decrease with the decrease of welding velocity. The displacement of material flow in the heat-mechanical affected zone by the tool with three-spiral-flute shoulder is much larger than that by the tool with inner-concave-flute shoulder or concentric-circles–flute shoulder. The above-mentioned results are verified by numerical simulation. For the tool with three-spiral-flute shoulder, the tensile strength of FSW joint increases with the decrease of welding velocity while the value of tensile strength attained by the welding velocity of 20 mm/min and the rotation speed of 1800 r/min is about 398 MPa, which is 80% more than that of parent mental tensile strength. Those verify that the tool with three-spiral-flute shoulder can be used to join the thin plate of Al alloy.
基金The project supported by National Natural Science Foundation of China
文摘An experimental investigation was carried out on the flow characteristic and hardening of steel 40 subjected to complex combined axial-torsional cyclic straining. For a specific cyclic strain path, the steel has mainly cyclic softening behavior when the strain amplitude is small. While with an increase of the effective strain amplitude, the softening becomes small, but there is the cyclic softening even though the steel is subjected to the cyclic loading by a square strain path. However, the steel has cyclic additional hardening by a nonproportional path, compared with the proportional cycling. Generally, the additional hardening is small and its historical effect is not obvious at small strain amplitude. The additional hardening is remarkable by a cross-triangular strain path of large strain amplitude. The memory of the history of nonproportional cyclic loading, the direction of plastic flow and the plastic modulus of the steel were also studied.
基金This work was supported by the National Science Foundation under the Grant 19302017 and 59472031
文摘The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile metal and the dispersive phase is assumed to consist of either aligned or randomly-oriented, elastic,, spheroidal inhomogeneities. The plastic flow and decreasing stiffness of the matrix during Eshelby's transformation strain of the equivalent inclusions are accounted for by using the deformation theory of plasticity. The explicit results of the instantaneous overall thermal expansion coefficients and the critical inelastic temperature changes are presented for aligned disc- and fiber-inclusions. For the spherical and randomly-oriented spheroidal inclusion, the present study demonstrates that when the yielding of the composites is governed by the average matrix stress, the overall response is always elastic in spite of the temperature change.
基金Supported partially by the Foundation of Henan Educational Committee under Grant No.2008A140011
文摘Langevin simulations are preformed on the depinning dynamics of fluid monolayer on a quenched substrate. With increase in the strength of the substrate, we find for the first time a crossover from elastic crystal to smectic flows as well as a crossover from smectic to plastic flows above the depinning. A power-law scaling relationship can be derived between the drift velocity and the driving force for both the elastic crystal and smectic flows, but fails to be obtained for the plastic flow. The power-law exponents are found to be no larger than 1 for the elastic crystal flow and larger than 1 for the smeetic flow. The critical driving force and the averaged intensity of Bragg peaks remain invariant basically in the regime of smectic flow. A sudden increase in the critical driving force is observed within the crossover from the smeetic to plastic flows, and the averaged intensity of Bragg peaks shows sudden decreases within the crossovers both from the elastic crystal to smectic flows and from the smectic to plastic flows. The results are helpful for understanding the slip dynamics of fluids on a molecular level.
文摘This paper reviews the recent progress in the studies of experimental rock mechanics and tectonophysics concerning seismology and physics of the Earths interior in China. The progress is presented in the following aspects: a) A lot of results of experiment and numerical simulation enrich our knowledge of the brittle fracturing process under the condition with heterogeneity in material and structure; b) Some new results on frictional behavior of non-homogeneous faults reveal the complexity of faulting behavior; c) Some new results on the brittle-plastic transition and plastic flow are obtained; especially the important progress is obtained on rheological properties of rocks in the lower crust and the upper mantle; d) A lot of experimental results are obtained on rock physics at high temperature and pressure and have been used in study of material composition and state. These results provide useful information for understanding the physical properties and deformation mechanisms of material of the Earths interior and earthquake physics.
