In rock engineering,natural cracks in rock masses subjected to external loads tend to initiate and propagate,leading to potential safety hazards.To investigate the effect of cracking behavior on the mechanical propert...In rock engineering,natural cracks in rock masses subjected to external loads tend to initiate and propagate,leading to potential safety hazards.To investigate the effect of cracking behavior on the mechanical properties of rocks,the cracking processes of pre-cracked rocks have been extensively studied using numerical modeling methods.The peridynamics(PD)exhibits advantages over other numerical methods due to the absence of the requirements for remeshing and external crack growth criterion.However,for modeling pre-cracked rock cracking processes under impact,current PD implementations lack generally applicable rock constitutive models and impact contact models,which leads to difficulties in determining rock material parameters and efficiently calculating impact loads.This paper proposes a non-ordinary state-based peridynamics(NOSBPD)modeling method integrating the Drucker-Prager(DP)plasticity model and an efficient contact model to address the above problems.In the proposed method,the Drucker-Prager plasticity model is integrated into the NOSBPD,thereby equipping NOSBPD with the capability to accurately characterize the nonlinear stress-strain relationship inherent in rocks.An efficient contact model between particles and meshes is designed to calculate the impact loads,which is essentially a coupling method of PD with the finite element method(FEM).The effectiveness of the proposed NOSBPD modeling method is verified by comparison with other numerical methods and experiments.Experimental results indicate that the proposed method can effectively and accurately predict the 3D cracking processes of pre-cracked cracks under impact loading,and the maximum principal stress is the key driver behind wing crack formation in pre-cracked rocks.展开更多
The effects of solid solution on the deformation behavior of binary Mg-xZn(x=0,1,2 wt%)alloys featuring a designated texture that enables extension twinning under tension parallel to the basal pole in most grains,were...The effects of solid solution on the deformation behavior of binary Mg-xZn(x=0,1,2 wt%)alloys featuring a designated texture that enables extension twinning under tension parallel to the basal pole in most grains,were investigated using in-situ neutron diffraction and the EVPSC-TDT model.Neutron diffraction was used to quantitatively track grain-level lattice strains and diffraction intensity changes(related to mechanical twinning)in differently oriented grains of each alloy during cyclic tensile/compressive loadings.These measurements were accurately captured by the model.The stress-strain curves of Mg-1 wt%Zn and Mg-2 wt%Zn alloys show as-expected solid solution strengthening from the addition of Zn compared to pure Mg.The macroscopic yielding and hardening behaviors are explained by alternating slip and twinning modes as calculated by the model.The solid solution's influence on individual deformation modes,including basal〈a〉slip,prismatic〈a〉slip,and extension twinning,was then quantitatively assessed in terms of activity,yielding behavior,and hardening response by combining neutron diffraction results with crystal plasticity predictions.The Mg-1 wt%Zn alloy displays distinct yielding and hardening behavior due to solid solution softening of prismatic〈a〉slip.Additionally,the dependence of extension twinning,in terms of the twinning volume fraction,on Zn content exhibits opposite trends under tensile and compressive loadings.展开更多
A polycrystal plasticity model was developed to analyze the room-temperature deformation behaviors of Mg-3A1-1Zn alloy（AZ31）.The uniaxial tension and compression tests at room temperature were conducted using cast a...A polycrystal plasticity model was developed to analyze the room-temperature deformation behaviors of Mg-3A1-1Zn alloy（AZ31）.The uniaxial tension and compression tests at room temperature were conducted using cast and extruded AZ31 rods with different textures and combined with the proposed model to reveal the deformation mechanisms.It is shown that,different flow curves of two specimens under tension and compression tests can be simulated by this model.The flow curves of AZ31 extrusions exhibit different shapes for tension and compression due to different activities of tensile twinning and pyramidalc＋a slip.The metallographic and TEM observations showed the equal twinning activities at the initial stage in tension and compression tests and the occurrence of pyramidalc＋a slip in compression of as-cast Mg-3A1-1Zn alloy with increasing the strain,which is consistent with the simulated results by the proposed model.展开更多
Low ductility and strength are major bottlenecks against Mg alloys’wide applications.In this work,we systematically design the composition and fabrication process for a low-alloyed Mg-Zn-Ca alloy,showing that it can ...Low ductility and strength are major bottlenecks against Mg alloys’wide applications.In this work,we systematically design the composition and fabrication process for a low-alloyed Mg-Zn-Ca alloy,showing that it can be extruded at low temperatures(~250℃)and high speeds(~2 mm/s).After the extrusion,this alloy exhibits a substantially weakened basal texture,relatively small grain size,very high tensile elongation(~30%),and good strength.The origin of the considerably improved ductility was studied using a combination of three-dimensional atom probe tomography(3D-APT),transmission electron microscopy(TEM),electron backscattered diffraction(EBSD)in conjunction with surface slip trace analysis,in-situ synchrotron X-ray diffraction,and elasto-plastic self-consistent(EPSC)modeling.Co-segregation of Zn and Ca atoms at a grain boundary is observed and associated with texture weakening and grain boundary mediated plasticity,both improving the ductility.While basal slip and prismatic slip are identified as the dominant deformation systems in the alloy,the ratio between their slip resistances is substantially reduced relative to pure Mg and most other Mg alloys,significantly contributing to the improved ductility of the alloy.This Mg-Zn-Ca alloy exhibiting excellent mechanical properties and low fabrication cost is a promising candidate for industrial productions.展开更多
A mesoscale model of plastic deformation of ferritic stainless steels （FSSs） is formulated by combining a crystal plasticity finite element model with 3D cellular automaton algorithm. The actual grain orientations o...A mesoscale model of plastic deformation of ferritic stainless steels （FSSs） is formulated by combining a crystal plasticity finite element model with 3D cellular automaton algorithm. The actual grain orientations of FSS cold rolling and annealing sheet have been detected by electron backscatter diffraction and selected to be assigned to the polycrystal model. The simulation results have been validated by comparing the calculated true stress-strain response with the experimental one. For the lack of considering the interactions of dislocations with impurities, there are no upper and lower yield points in the simulation stress-strain curves. However, the calculated yield strength and the stress-strain response after yielding agree well with the real material. The local stress and strain fields show inhomogeneous at mesoscale. The plastic deformations of the grains with typical orientations have been characterized. The analysis reveals that the grains with fiber texture show higher thickness reduction ratio as compared to others. The deformation behaviors of the grains in polycrystal are not only related to the orientations but also to the interactions from adjacent grains.展开更多
In this work,we investigated the mechanical properties and corresponding deformation mechanisms of an Al1Mg0.4Si alloy,which exhibited significantly higher strength and outstanding strain hardening capacity at 77 K co...In this work,we investigated the mechanical properties and corresponding deformation mechanisms of an Al1Mg0.4Si alloy,which exhibited significantly higher strength and outstanding strain hardening capacity at 77 K compared to its counterparts at 298 K.The deformation mechanisms responsible for the excellent strength-ductility synergy and extraordinary strain hardening capacity at cryogenic temperature were elucidated through a combined experimental and simulation study.The results reveal the presence of numerous slip traces and microbands throughout grain surfaces during deformation at 298 K,whereas at 77 K,vague grain surfaces dominate,indicating the simultaneous operation of multiple slip systems.Transmission electron microscopy(TEM)analysis using the two-beam diffraction technique demonstrates the presence of dislocations with several different Burgers vectors inside a grain at cryogenic temperature,confirming the activation of multiple slip systems.The accumulation of dislocations facilitated by these multiple slip systems,combined with the high dislocation density,contributes to strain hardening and remarkable uniform elongation at 77 K.A modified dislocation density-based crystal plasticity model,incorporating the effect of grain boundary hardening(GBH)and temperature,was developed to gain a better understanding of the underlying mechanisms governing alloy’s strength and plasticity.The GBH effect significantly enhances statistically stored dislocation(SSD)density and screw dislocation proportion,which promote homogeneous deformation and enhance strain hardening capacity at cryogenic temperature.These findings deepen the understanding of plastic deformation at cryogenic temperatures and pave the way for the development of ultrahigh-performance metallic materials for cryogenic applications.展开更多
The complex grain fragmentation mechanisms of coarse grains in titanium alloys under multi-directional forging(MDF)directly influence the optimization and control of primary hot working processes.This study conducted ...The complex grain fragmentation mechanisms of coarse grains in titanium alloys under multi-directional forging(MDF)directly influence the optimization and control of primary hot working processes.This study conducted MDF experiments onβ-phase as-cast Ti-6554 alloy and simulated non-uniform deformation during cyclic multi-directional compression through macro-and micro-deformation modeling.The results revealed that friction and surface cooling caused low strain and tensile stress concentration at billet edges,leading to mixed grain structures.In contrast,high strain and triaxial compressive stress at billet centers facilitated uniform grain refinement.After 14 compressions and 4 intermediate reheating processes,coarse grains of the billet were refined from 2-5 mm to 0.25-0.50 mm,achieving uniform grain sizes across different regions.For the first time,the orientation evolution of grains with different morphologies during multi-directional compressions was visualized microscopically.Columnar grains were found to be more easily subdivided than equiaxed grains due to local strain accumulation.Under cumulative compressions,grain orientations gradually rotated from uniform to random,driving continuous dynamic recrystallization(CDRX).Slip system interactions and concentrated misorientation led to the formation and extension of transition and shear bands,inducing grain fragmentation dominated by transgranular subdivided CDRX.Smooth grain boundaries transformed into serrated ones after multiple passes,providing additional nucleation sites for discontinuous dynamic recrystallization(DDRX)and facilitating boundary expand CDRX.The interaction of diverse DRX mechanisms was the fundamental cause of grain refinement.This study clarified the principles of refining and homogenizing millimeter-grade coarse grains under increasing forging strain,offering valuable insights for the development of primary hot processing techniques for as-castβtitanium alloys.展开更多
Non-Schmid(NS)effects in body-centered cubic(BCC)single-phase metals have received special attention in recent years.However,a deep understanding of these effects in the BCC phase of dual-phase(DP)steels has not yet b...Non-Schmid(NS)effects in body-centered cubic(BCC)single-phase metals have received special attention in recent years.However,a deep understanding of these effects in the BCC phase of dual-phase(DP)steels has not yet been reached.This study explores the NS effects in ferrite-martensite DP steels,where the ferrite phase has a BCC crystallographic structure and exhibits NS effects.The influences of NS stress components on the mechanical response of DP steels are studied,including stress/strain partitioning,plastic flow,and yield surface.To this end,the mechanical behavior of the two phases is described by dislocation density-based crystal plasticity constitutive models,with the NS effect only incorporated into the ferrite phase modeling.The NS stress contribution is revealed for two types of microstructures commonly observed in DP steels:equiaxed phases with random grain orientations,and elongated phases with preferred grain orientations.Our results show that,in the case of a microstructure with equiaxed phases,the normal NS stress components play significant roles in tension-compression asymmetry.By contrast,in microstructures with elongated phases,a combined influence of crystallographic texture and NS effect is evident.These findings advance our knowledge of the intricate interplay between microstructural features and NS effects and help to elucidate the mechanisms underlying anisotropic-asymmetric plastic behavior of DP steels.展开更多
Buckling restrained braces （BRBs） have been widely applied in seismic mitigation since they were introduced in the 1970s. However, traditional BRBs have several disadvantages caused by using a steel tube to envelope...Buckling restrained braces （BRBs） have been widely applied in seismic mitigation since they were introduced in the 1970s. However, traditional BRBs have several disadvantages caused by using a steel tube to envelope the mortar to prevent the core plate from buckling, such as： complex interfaces between the materials used, uncertain precision, and time consumption during the manufacturing processes. In this study, a new device called the multi-curve buckling restrained brace （MC-BRB） is proposed to overcome these disadvantages. The new device consists of a core plate with multiple neck portions assembled to form multiple energy dissipation segments, and the enlarged segment, lateral support elements and constraining elements to prevent the BRB from buckling. The enlarged segment located in the middle of the core plate can be welded to the lateral support and constraining elements to increase buckling resistance and to prevent them from sliding during earthquakes. Component tests and a series of shaking table tests on a full-scale steel structure equipped with MC-BRBs were carried out to investigate the behavior and capability of this new BRB design for seismic mitigation. The experimental results illustrate that the MC-BRB possesses a stable mechanical behavior under cyclic loadings and provides good protection to structures during earthquakes. Also, a mathematical model has been developed to simulate the mechanical characteristics of BRBs.展开更多
in order to evaluate the capacity of reinforced concrete （RC） structures subjected to blast Ioadings, the damaged plasticity model for concrete was used in the analysis of the dynamic responses of blast-loaded RC st...in order to evaluate the capacity of reinforced concrete （RC） structures subjected to blast Ioadings, the damaged plasticity model for concrete was used in the analysis of the dynamic responses of blast-loaded RC structures, and all three failure modes were numerically simulated by the finite element software ABAQUS. Simulation results agree with the experimental observations. It is demonstrated that the damaged plasticity model for concrete in the finite element software ABAQUS can predict dynamic responses and typical flexure, flexure-shear and direct shear failure modes of the blast-loaded RC structures.展开更多
Magnesium(Mg) alloys with hexagonal close-packed(HCP) structure usually have a poor ductility at room temperature. The addition of yttrium(Y) can improve the ductility of Mg alloys. To understand the underlying mechan...Magnesium(Mg) alloys with hexagonal close-packed(HCP) structure usually have a poor ductility at room temperature. The addition of yttrium(Y) can improve the ductility of Mg alloys. To understand the underlying mechanism, crystal plasticity finite element method(CPFEM) was employed to simulate the tensile deformation of a Mg-0.8 wt% Y alloy. The simulated stress–strain curve and the grain-scale slip activities were compared with an in-situ tensile test conducted in a scanning electron microscope.According to the CPFEM result, basal slip is the dominant deformation mode in the plastic deformation stage, accounting for about 50% of total strain. Prismatic slip and pyramidal a slip are responsible for about 25% and 20% of the total strain, respectively. Pyramidal c + a slip and twinning, on the other hand,accommodate much less strain.展开更多
To investigate the relationship between macro-plastic behavior and meso-deformation mechanism of Mg alloy AZ31, the mathematical models for various deformation mechanisms of slip, twinning and detwinning are establish...To investigate the relationship between macro-plastic behavior and meso-deformation mechanism of Mg alloy AZ31, the mathematical models for various deformation mechanisms of slip, twinning and detwinning are established, respectively. Furthermore, in order to capture the Bauschinger effect under cyclic loading, the back stress is introduced into the three independent deformation mechanisms, respectively. Finally, using the above-mentioned model, a new cyclic plastic constitutive model based on the constitutive theory of crystal deformation for magnesium alloy is established. On this basis, the numerical simulation for AZ31 under cyclic loading with the axial strain amplitude of 1.2% is carried out in accordance with the aforementioned crystal plas- ticity theory associated with the representative volume element model. The comparison between the stress-strain curves obtained from the simulation and the experiments shows that the macro- scopic mechanical responses predicted using the proposed model are in good agreement with the experimental results. In particular, the unique characteristics of cyclic macro-plastic behavior observed in the experiments can be satisfactorily captured by the presented crystal plasticity model. At the mesoscale, these features are caused by the alternate occurrence of twinning and detwinning mechanisms. The further analysis of meso-plastic behavior shows that there are het- erogeneous distributions of twinning, stress-strain and stress triaxiality in polycrystal under cyclic loading.展开更多
A constitutive model is developed for the transformation, reorientation and plastic deformation of shape memory alloys （SMAs）. It is based on the concept that an SMA is a mixture composed of austenite and martensite...A constitutive model is developed for the transformation, reorientation and plastic deformation of shape memory alloys （SMAs）. It is based on the concept that an SMA is a mixture composed of austenite and martensite, the volume fraction of each phase is transformable with the change of applied thermal-mechanical loading, and the constitutive behavior of the SMA is the combination of the individual behavior of its two phases. The deformation of the martensite is separated into elastic, thermal, reorientation and plastic parts, and that of the austenite is separated into elastic, thermal and plastic parts. Making use of the Tanaka＇s transformation rule modified by taking into account the effect of plastic deformation, the constitutive model of the SMA is obtained. The ferroelasticity, pseudoelastieity and shape memory effect of SMA Au-47.5 at.%Cd, and the pseudoelasticity and shape memory effect as well as plastic deformation and its effect of an NiTi SMA, are analyzed and compared with experimental results.展开更多
Water-based lubrication is an effective method to achieve superlubricity,which implies a friction coefficient in the order of 10−3 or lower.Recent numerical,analytical,and experimental studies confirm that the surface...Water-based lubrication is an effective method to achieve superlubricity,which implies a friction coefficient in the order of 10−3 or lower.Recent numerical,analytical,and experimental studies confirm that the surface force effect is crucial for realizing water-based superlubricity.To enhance the contribution of the surface force,soft and plastic materials can be utilized as friction pair materials because of their effect in increasing the contact area.A new numerical model of water-based lubrication that considers the surface force between plastic and elastic materials is developed in this study to investigate the effect of plastic flow in water-based lubrication.Considering the complexity of residual stress accumulation in lubrication problems,a simplified plastic model is proposed,which merely calculates the result of the dry contact solution and avoids repeated calculations of the plastic flow.The results of the two models show good agreement.Plastic deformation reduces the local contact pressure and enhances the function of the surface force,thus resulting in a lower friction coefficient.展开更多
The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio（Sp/C）,water to cement ratio（w/c）,...The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio（Sp/C）,water to cement ratio（w/c）,temperature,and time were discussed.Fresh cement pastes with Sp/Cs in the range of 0 to 2.0% and varied W/Cs from 0.25 to 0.5 were prepared and tested at 0,20 and 40 °C,respectively.Flowability and rheologicaltests on cement pastes were conducted to characterize the development of the rheologicalbehavior of fresh cement pastes over time.The exprimentalresults indicate that the initialflowability and flowability retention over shelf time increase with the growth in superplasticizer dosage due to the plasticizing effect and retardation effect of superplasticizer.Higher temperature usually leads to a sharper drop in initialflowability and flowability retention.However,for the cement paste with high Sp/C or w/c,the flowability is slightly affected by temperature.Yield stress and plastic viscosity show similar variation trends to the flowability under the abovementioned influentialfactors at low Sp/C.In the case of high Sp/C,yield stress and plastic viscosity start to decline over shelf time and the decreasing rate descends at elevated temperature.Moreover,two equations to roughly predict yield stress and plastic viscosity of the fresh cement pastes incorporating Sp/C,w/c,temperature and time are developed on the basis of the existing models,in which experimentalconstants can be extracted from a database created by the rheologicaltest results.展开更多
The distribution of shear stress on the cross-section of plastic metal solid circular shaft under pure torsion yielding, the applicability of complete plastic model assumption and the shear stress formula were researc...The distribution of shear stress on the cross-section of plastic metal solid circular shaft under pure torsion yielding, the applicability of complete plastic model assumption and the shear stress formula were researched. Based on the shear stress formula of circular shaft under pure torsion in elastic stage, the formula of torque in elastic stage and the definition of yield, it is obtained that the yielding stage of plastic metal shaft under pure torsion is only a surface phenomenon of torque-torsion angle relationship, and the distribution of shear stress is essentially different from that of tensile stress when yielding under uniaxial tension. The pure torsion platform-torsion angle and the shape of torque-torsion angle curve cannot change the distribution of shear stress on the shaft cross-section. The distribution of shear stress is still linear with the maximum shear stress ts. The complete plasticity model assumption is not in accordance with the actual situation of shaft under torsion. The experimental strength data of nine plastic metals are consistent with the calculated results of the new limiting strain energy strength theory （LSEST）. The traditional yield stress formula for plastic shaft under torsion is reasonable. The shear stress formula based on the plane assumption in material mechanics is applicable for all loaded stages of torsion shaft.展开更多
The complex micromechanical response among grains remains a persistent challenge to understand the deformation mechanism of titanium alloys during cold rolling.Therefore,in this work,a multiscale crystal plasticity fi...The complex micromechanical response among grains remains a persistent challenge to understand the deformation mechanism of titanium alloys during cold rolling.Therefore,in this work,a multiscale crystal plasticity finite element method of dual-phase alloy was proposed and secondarily developed based on LS-DYNA software.Afterward,the texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr alloy,based on the realistic 3D microstructure,during cold rolling(20%thickness reduction)were systematically investigated.The relative activity of the■slip system in theαphase gradually increased,and then served as the main slip mode at lower Schmid factor(<0.2).In contrast,the contribution of the■slip system to the overall plastic deformation was relatively limited.For theβphase,the relative activity of the<111>{110}slip system showed an upward tendency,indicating the important role of the critical resolved shear stress relationship in the relative activity evolutions.Furthermore,the abnormally high strain of very fewβgrains was found,which was attributed to their severe rotations compelled by the neighboring pre-deformedαgrains.The calculated pole figures,rotation axes,and compelled rotation behavior exhibited good agreement to the experimental results.展开更多
The most critical issue in the steel catenary riser design is to evaluate the fatigue damage in the touchdown zone accurately. Appropriate modeling of the riser-soil resistance in the touchdown zone can lead to signif...The most critical issue in the steel catenary riser design is to evaluate the fatigue damage in the touchdown zone accurately. Appropriate modeling of the riser-soil resistance in the touchdown zone can lead to significant cost reduction by optimizing design. This paper presents a plasticity model that can be applied to numerically simulate riser-soil interaction and evaluate dynamic responses and the fatigue damage of a steel catenary riser in the touchdown zone. Utilizing the model, numerous riser-soil elements are attached to the steel catenary riser finite elements, in which each simulates local foundation restraint along the riser touchdown zone. The riser-soil interaction plasticity model accounts for the behavior within an allowable combined loading surface. The model will be represented in this paper, allowing simple numerical implementation. More importantly, it can be incorporated within the structural analysis of a steel catenary riser with the finite element method. The applicability of the model is interpreted theoretically and the results are shown through application to an offshore 8.625 steel catenary riser example. The fatigue analysis results of the liner elastic riser-soil model are also shown. According to the comparison results of the two models, the fatigue life analysis results of the plasticity framework are reasonable and the horizontal effects of the riser-soil interaction can be included.展开更多
This paper establishes an anisotropic plastic material model to analyze the elasto-plastic behavior of masonry in plane stress state.Being an anisotropic material,masonry has different constitutive relation and fractu...This paper establishes an anisotropic plastic material model to analyze the elasto-plastic behavior of masonry in plane stress state.Being an anisotropic material,masonry has different constitutive relation and fracture energies along each orthotropic axes.Considering the unique material properties of masonry,a new yield criterion for masonry is proposed combining the Hill's yield criterion and the Rankine's yield criterion.The new yield criterion not only introduces compression friction coefficient of shear but also considers yield functions for independent stress state along two material axes of tension.To solve the involved nonlinear equations in numerical analysis,several nonlinear methods are implemented,including Newton-Raphson method for nonlinear equations and Implicit Euler backward mapping algorithm to update stresses.To verify the proposed material model of masonry,a series of tests are operated.The simulation results show that the new developed material model implements successfully.Compared with isotropic material model,the proposed model performs better in elasto-plastic analysis of masonry in plane stress state.The proposed anisotropic model is capable of simulating elasto-plastic behavior of masonry and can be used in related applications.展开更多
Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high...Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high purity aluminum by ECAE at ambient temperature. The experimental results showed that high strain rate and large deformation could induce dynamic recrystallization.Based on dislocation dynamics and grain orientation change enhanced by plastic deformation,a model for the recrystallization process is developed. The model is used to explain the ultra fine grains which are formed at a temperature still much lower than that for the conventional recrystallization展开更多
基金support from the National Natural Science Foundation of China(Grant Nos.42277161 and 42230709).
文摘In rock engineering,natural cracks in rock masses subjected to external loads tend to initiate and propagate,leading to potential safety hazards.To investigate the effect of cracking behavior on the mechanical properties of rocks,the cracking processes of pre-cracked rocks have been extensively studied using numerical modeling methods.The peridynamics(PD)exhibits advantages over other numerical methods due to the absence of the requirements for remeshing and external crack growth criterion.However,for modeling pre-cracked rock cracking processes under impact,current PD implementations lack generally applicable rock constitutive models and impact contact models,which leads to difficulties in determining rock material parameters and efficiently calculating impact loads.This paper proposes a non-ordinary state-based peridynamics(NOSBPD)modeling method integrating the Drucker-Prager(DP)plasticity model and an efficient contact model to address the above problems.In the proposed method,the Drucker-Prager plasticity model is integrated into the NOSBPD,thereby equipping NOSBPD with the capability to accurately characterize the nonlinear stress-strain relationship inherent in rocks.An efficient contact model between particles and meshes is designed to calculate the impact loads,which is essentially a coupling method of PD with the finite element method(FEM).The effectiveness of the proposed NOSBPD modeling method is verified by comparison with other numerical methods and experiments.Experimental results indicate that the proposed method can effectively and accurately predict the 3D cracking processes of pre-cracked cracks under impact loading,and the maximum principal stress is the key driver behind wing crack formation in pre-cracked rocks.
基金supported by the National Research Foundation grant funded by the Korean government(No,2023R1A2C2007190,RS-2024-00398068)partially funded by the Natural Science Foundation of Shandong Province,China(No.ZR2022QE206).
文摘The effects of solid solution on the deformation behavior of binary Mg-xZn(x=0,1,2 wt%)alloys featuring a designated texture that enables extension twinning under tension parallel to the basal pole in most grains,were investigated using in-situ neutron diffraction and the EVPSC-TDT model.Neutron diffraction was used to quantitatively track grain-level lattice strains and diffraction intensity changes(related to mechanical twinning)in differently oriented grains of each alloy during cyclic tensile/compressive loadings.These measurements were accurately captured by the model.The stress-strain curves of Mg-1 wt%Zn and Mg-2 wt%Zn alloys show as-expected solid solution strengthening from the addition of Zn compared to pure Mg.The macroscopic yielding and hardening behaviors are explained by alternating slip and twinning modes as calculated by the model.The solid solution's influence on individual deformation modes,including basal〈a〉slip,prismatic〈a〉slip,and extension twinning,was then quantitatively assessed in terms of activity,yielding behavior,and hardening response by combining neutron diffraction results with crystal plasticity predictions.The Mg-1 wt%Zn alloy displays distinct yielding and hardening behavior due to solid solution softening of prismatic〈a〉slip.Additionally,the dependence of extension twinning,in terms of the twinning volume fraction,on Zn content exhibits opposite trends under tensile and compressive loadings.
基金Project(51201092)supported by the National Natural Science Foundation of China
文摘A polycrystal plasticity model was developed to analyze the room-temperature deformation behaviors of Mg-3A1-1Zn alloy（AZ31）.The uniaxial tension and compression tests at room temperature were conducted using cast and extruded AZ31 rods with different textures and combined with the proposed model to reveal the deformation mechanisms.It is shown that,different flow curves of two specimens under tension and compression tests can be simulated by this model.The flow curves of AZ31 extrusions exhibit different shapes for tension and compression due to different activities of tensile twinning and pyramidalc＋a slip.The metallographic and TEM observations showed the equal twinning activities at the initial stage in tension and compression tests and the occurrence of pyramidalc＋a slip in compression of as-cast Mg-3A1-1Zn alloy with increasing the strain,which is consistent with the simulated results by the proposed model.
基金financially supported by the National Key Research and Development Program of China(No.2016YFB0701203)the National Natural Science Foundation of China(Nos.51631006,51671127 and 51825101)+3 种基金sponsored by the Youth Cheung Kong Scholars Programthe Shanghai Rising-Star Programthe support provided by the U.S.National Science Foundation(No.OIA-1757371)Use of the Advanced Photon Source was supported by the United States Department of Energy,Office of Science,Office of Basic Energy Sciences(No.DE-AC02-06CH11357)。
文摘Low ductility and strength are major bottlenecks against Mg alloys’wide applications.In this work,we systematically design the composition and fabrication process for a low-alloyed Mg-Zn-Ca alloy,showing that it can be extruded at low temperatures(~250℃)and high speeds(~2 mm/s).After the extrusion,this alloy exhibits a substantially weakened basal texture,relatively small grain size,very high tensile elongation(~30%),and good strength.The origin of the considerably improved ductility was studied using a combination of three-dimensional atom probe tomography(3D-APT),transmission electron microscopy(TEM),electron backscattered diffraction(EBSD)in conjunction with surface slip trace analysis,in-situ synchrotron X-ray diffraction,and elasto-plastic self-consistent(EPSC)modeling.Co-segregation of Zn and Ca atoms at a grain boundary is observed and associated with texture weakening and grain boundary mediated plasticity,both improving the ductility.While basal slip and prismatic slip are identified as the dominant deformation systems in the alloy,the ratio between their slip resistances is substantially reduced relative to pure Mg and most other Mg alloys,significantly contributing to the improved ductility of the alloy.This Mg-Zn-Ca alloy exhibiting excellent mechanical properties and low fabrication cost is a promising candidate for industrial productions.
基金supported by the National Natural Science Foundation of China(No.51604058)the Fundamental Research Funds for the Central Universities of China+1 种基金the Scientific Research Fund of Liaoning Provincial Education Department under Grant No.L2015120the Open Research Fund from the State Key Laboratory of Rolling and Automation,Northeastern University,China
文摘A mesoscale model of plastic deformation of ferritic stainless steels （FSSs） is formulated by combining a crystal plasticity finite element model with 3D cellular automaton algorithm. The actual grain orientations of FSS cold rolling and annealing sheet have been detected by electron backscatter diffraction and selected to be assigned to the polycrystal model. The simulation results have been validated by comparing the calculated true stress-strain response with the experimental one. For the lack of considering the interactions of dislocations with impurities, there are no upper and lower yield points in the simulation stress-strain curves. However, the calculated yield strength and the stress-strain response after yielding agree well with the real material. The local stress and strain fields show inhomogeneous at mesoscale. The plastic deformations of the grains with typical orientations have been characterized. The analysis reveals that the grains with fiber texture show higher thickness reduction ratio as compared to others. The deformation behaviors of the grains in polycrystal are not only related to the orientations but also to the interactions from adjacent grains.
基金supported by the National Natural Science Foundation of China(Nos.92263201,51927801,52001160,and 52205378)the National Key Research&Development Plan(Nos.2020YFA0405900 and 2019YFA0708801)Natural Science Foundation of Jiangsu Province(No.BK20202010).
文摘In this work,we investigated the mechanical properties and corresponding deformation mechanisms of an Al1Mg0.4Si alloy,which exhibited significantly higher strength and outstanding strain hardening capacity at 77 K compared to its counterparts at 298 K.The deformation mechanisms responsible for the excellent strength-ductility synergy and extraordinary strain hardening capacity at cryogenic temperature were elucidated through a combined experimental and simulation study.The results reveal the presence of numerous slip traces and microbands throughout grain surfaces during deformation at 298 K,whereas at 77 K,vague grain surfaces dominate,indicating the simultaneous operation of multiple slip systems.Transmission electron microscopy(TEM)analysis using the two-beam diffraction technique demonstrates the presence of dislocations with several different Burgers vectors inside a grain at cryogenic temperature,confirming the activation of multiple slip systems.The accumulation of dislocations facilitated by these multiple slip systems,combined with the high dislocation density,contributes to strain hardening and remarkable uniform elongation at 77 K.A modified dislocation density-based crystal plasticity model,incorporating the effect of grain boundary hardening(GBH)and temperature,was developed to gain a better understanding of the underlying mechanisms governing alloy’s strength and plasticity.The GBH effect significantly enhances statistically stored dislocation(SSD)density and screw dislocation proportion,which promote homogeneous deformation and enhance strain hardening capacity at cryogenic temperature.These findings deepen the understanding of plastic deformation at cryogenic temperatures and pave the way for the development of ultrahigh-performance metallic materials for cryogenic applications.
基金supported by the National Key Research and Development Program of China(No.2022YFB3706901)the National Natural Science Foundation of China(No.52274382)。
文摘The complex grain fragmentation mechanisms of coarse grains in titanium alloys under multi-directional forging(MDF)directly influence the optimization and control of primary hot working processes.This study conducted MDF experiments onβ-phase as-cast Ti-6554 alloy and simulated non-uniform deformation during cyclic multi-directional compression through macro-and micro-deformation modeling.The results revealed that friction and surface cooling caused low strain and tensile stress concentration at billet edges,leading to mixed grain structures.In contrast,high strain and triaxial compressive stress at billet centers facilitated uniform grain refinement.After 14 compressions and 4 intermediate reheating processes,coarse grains of the billet were refined from 2-5 mm to 0.25-0.50 mm,achieving uniform grain sizes across different regions.For the first time,the orientation evolution of grains with different morphologies during multi-directional compressions was visualized microscopically.Columnar grains were found to be more easily subdivided than equiaxed grains due to local strain accumulation.Under cumulative compressions,grain orientations gradually rotated from uniform to random,driving continuous dynamic recrystallization(CDRX).Slip system interactions and concentrated misorientation led to the formation and extension of transition and shear bands,inducing grain fragmentation dominated by transgranular subdivided CDRX.Smooth grain boundaries transformed into serrated ones after multiple passes,providing additional nucleation sites for discontinuous dynamic recrystallization(DDRX)and facilitating boundary expand CDRX.The interaction of diverse DRX mechanisms was the fundamental cause of grain refinement.This study clarified the principles of refining and homogenizing millimeter-grade coarse grains under increasing forging strain,offering valuable insights for the development of primary hot processing techniques for as-castβtitanium alloys.
基金supported by the National Natural Science Foundation of China(Grant Nos.12202153 and 12072123).
文摘Non-Schmid(NS)effects in body-centered cubic(BCC)single-phase metals have received special attention in recent years.However,a deep understanding of these effects in the BCC phase of dual-phase(DP)steels has not yet been reached.This study explores the NS effects in ferrite-martensite DP steels,where the ferrite phase has a BCC crystallographic structure and exhibits NS effects.The influences of NS stress components on the mechanical response of DP steels are studied,including stress/strain partitioning,plastic flow,and yield surface.To this end,the mechanical behavior of the two phases is described by dislocation density-based crystal plasticity constitutive models,with the NS effect only incorporated into the ferrite phase modeling.The NS stress contribution is revealed for two types of microstructures commonly observed in DP steels:equiaxed phases with random grain orientations,and elongated phases with preferred grain orientations.Our results show that,in the case of a microstructure with equiaxed phases,the normal NS stress components play significant roles in tension-compression asymmetry.By contrast,in microstructures with elongated phases,a combined influence of crystallographic texture and NS effect is evident.These findings advance our knowledge of the intricate interplay between microstructural features and NS effects and help to elucidate the mechanisms underlying anisotropic-asymmetric plastic behavior of DP steels.
基金Science Council in Chinese Taipei Under Grant No.NSC 94-2211-E-035-015
文摘Buckling restrained braces （BRBs） have been widely applied in seismic mitigation since they were introduced in the 1970s. However, traditional BRBs have several disadvantages caused by using a steel tube to envelope the mortar to prevent the core plate from buckling, such as： complex interfaces between the materials used, uncertain precision, and time consumption during the manufacturing processes. In this study, a new device called the multi-curve buckling restrained brace （MC-BRB） is proposed to overcome these disadvantages. The new device consists of a core plate with multiple neck portions assembled to form multiple energy dissipation segments, and the enlarged segment, lateral support elements and constraining elements to prevent the BRB from buckling. The enlarged segment located in the middle of the core plate can be welded to the lateral support and constraining elements to increase buckling resistance and to prevent them from sliding during earthquakes. Component tests and a series of shaking table tests on a full-scale steel structure equipped with MC-BRBs were carried out to investigate the behavior and capability of this new BRB design for seismic mitigation. The experimental results illustrate that the MC-BRB possesses a stable mechanical behavior under cyclic loadings and provides good protection to structures during earthquakes. Also, a mathematical model has been developed to simulate the mechanical characteristics of BRBs.
基金Supported by National Natural Science Foundation of China (No.50638030 and 50525825)National Science and Technology Support Program (No.2006BAJ13B02).
文摘in order to evaluate the capacity of reinforced concrete （RC） structures subjected to blast Ioadings, the damaged plasticity model for concrete was used in the analysis of the dynamic responses of blast-loaded RC structures, and all three failure modes were numerically simulated by the finite element software ABAQUS. Simulation results agree with the experimental observations. It is demonstrated that the damaged plasticity model for concrete in the finite element software ABAQUS can predict dynamic responses and typical flexure, flexure-shear and direct shear failure modes of the blast-loaded RC structures.
基金financially supported by the National Natural Science Foundation of China (Nos. 51631006, 51671127 and 51825101)
文摘Magnesium(Mg) alloys with hexagonal close-packed(HCP) structure usually have a poor ductility at room temperature. The addition of yttrium(Y) can improve the ductility of Mg alloys. To understand the underlying mechanism, crystal plasticity finite element method(CPFEM) was employed to simulate the tensile deformation of a Mg-0.8 wt% Y alloy. The simulated stress–strain curve and the grain-scale slip activities were compared with an in-situ tensile test conducted in a scanning electron microscope.According to the CPFEM result, basal slip is the dominant deformation mode in the plastic deformation stage, accounting for about 50% of total strain. Prismatic slip and pyramidal a slip are responsible for about 25% and 20% of the total strain, respectively. Pyramidal c + a slip and twinning, on the other hand,accommodate much less strain.
基金Project （11462002） supported by the National Natural Science Foundation of China Project （2016GXNSFAA380218） supported by Guangxi Natural Science Foundation, China+1 种基金 Project （2014ZDK002） supported by the Open Project of Guangxi Key Laboratory of Disaster Prevention and Structural Safety at Guangxi University, China and Project （Z01） supported by the Science Foundation for Doctorate Research of Guangxi University of Science and Technology, China.
文摘To investigate the relationship between macro-plastic behavior and meso-deformation mechanism of Mg alloy AZ31, the mathematical models for various deformation mechanisms of slip, twinning and detwinning are established, respectively. Furthermore, in order to capture the Bauschinger effect under cyclic loading, the back stress is introduced into the three independent deformation mechanisms, respectively. Finally, using the above-mentioned model, a new cyclic plastic constitutive model based on the constitutive theory of crystal deformation for magnesium alloy is established. On this basis, the numerical simulation for AZ31 under cyclic loading with the axial strain amplitude of 1.2% is carried out in accordance with the aforementioned crystal plas- ticity theory associated with the representative volume element model. The comparison between the stress-strain curves obtained from the simulation and the experiments shows that the macro- scopic mechanical responses predicted using the proposed model are in good agreement with the experimental results. In particular, the unique characteristics of cyclic macro-plastic behavior observed in the experiments can be satisfactorily captured by the presented crystal plasticity model. At the mesoscale, these features are caused by the alternate occurrence of twinning and detwinning mechanisms. The further analysis of meso-plastic behavior shows that there are het- erogeneous distributions of twinning, stress-strain and stress triaxiality in polycrystal under cyclic loading.
基金Project supported by the National Natural Science Foundation of China (No. 10976032)
文摘A constitutive model is developed for the transformation, reorientation and plastic deformation of shape memory alloys （SMAs）. It is based on the concept that an SMA is a mixture composed of austenite and martensite, the volume fraction of each phase is transformable with the change of applied thermal-mechanical loading, and the constitutive behavior of the SMA is the combination of the individual behavior of its two phases. The deformation of the martensite is separated into elastic, thermal, reorientation and plastic parts, and that of the austenite is separated into elastic, thermal and plastic parts. Making use of the Tanaka＇s transformation rule modified by taking into account the effect of plastic deformation, the constitutive model of the SMA is obtained. The ferroelasticity, pseudoelastieity and shape memory effect of SMA Au-47.5 at.%Cd, and the pseudoelasticity and shape memory effect as well as plastic deformation and its effect of an NiTi SMA, are analyzed and compared with experimental results.
基金National Natural Science Foundation of China(Grant No.51925506)National Key R&D Program of China(Grants No.2020YFA0711003).
文摘Water-based lubrication is an effective method to achieve superlubricity,which implies a friction coefficient in the order of 10−3 or lower.Recent numerical,analytical,and experimental studies confirm that the surface force effect is crucial for realizing water-based superlubricity.To enhance the contribution of the surface force,soft and plastic materials can be utilized as friction pair materials because of their effect in increasing the contact area.A new numerical model of water-based lubrication that considers the surface force between plastic and elastic materials is developed in this study to investigate the effect of plastic flow in water-based lubrication.Considering the complexity of residual stress accumulation in lubrication problems,a simplified plastic model is proposed,which merely calculates the result of the dry contact solution and avoids repeated calculations of the plastic flow.The results of the two models show good agreement.Plastic deformation reduces the local contact pressure and enhances the function of the surface force,thus resulting in a lower friction coefficient.
基金Funded by the National Natural Science Foundation of China(Nos.U1301241 and U1234211)the Postdoctoral Science Foundation of China(No.2015M580042)
文摘The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio（Sp/C）,water to cement ratio（w/c）,temperature,and time were discussed.Fresh cement pastes with Sp/Cs in the range of 0 to 2.0% and varied W/Cs from 0.25 to 0.5 were prepared and tested at 0,20 and 40 °C,respectively.Flowability and rheologicaltests on cement pastes were conducted to characterize the development of the rheologicalbehavior of fresh cement pastes over time.The exprimentalresults indicate that the initialflowability and flowability retention over shelf time increase with the growth in superplasticizer dosage due to the plasticizing effect and retardation effect of superplasticizer.Higher temperature usually leads to a sharper drop in initialflowability and flowability retention.However,for the cement paste with high Sp/C or w/c,the flowability is slightly affected by temperature.Yield stress and plastic viscosity show similar variation trends to the flowability under the abovementioned influentialfactors at low Sp/C.In the case of high Sp/C,yield stress and plastic viscosity start to decline over shelf time and the decreasing rate descends at elevated temperature.Moreover,two equations to roughly predict yield stress and plastic viscosity of the fresh cement pastes incorporating Sp/C,w/c,temperature and time are developed on the basis of the existing models,in which experimentalconstants can be extracted from a database created by the rheologicaltest results.
文摘The distribution of shear stress on the cross-section of plastic metal solid circular shaft under pure torsion yielding, the applicability of complete plastic model assumption and the shear stress formula were researched. Based on the shear stress formula of circular shaft under pure torsion in elastic stage, the formula of torque in elastic stage and the definition of yield, it is obtained that the yielding stage of plastic metal shaft under pure torsion is only a surface phenomenon of torque-torsion angle relationship, and the distribution of shear stress is essentially different from that of tensile stress when yielding under uniaxial tension. The pure torsion platform-torsion angle and the shape of torque-torsion angle curve cannot change the distribution of shear stress on the shaft cross-section. The distribution of shear stress is still linear with the maximum shear stress ts. The complete plasticity model assumption is not in accordance with the actual situation of shaft under torsion. The experimental strength data of nine plastic metals are consistent with the calculated results of the new limiting strain energy strength theory （LSEST）. The traditional yield stress formula for plastic shaft under torsion is reasonable. The shear stress formula based on the plane assumption in material mechanics is applicable for all loaded stages of torsion shaft.
基金financially supported by the Natural Science Foundation of Chongqing(No.Cstc2020jcyj-msxmX0094)the Joint Research Programs between Belarusian Republican Foundation for Fundamental Research and Beijing Institute of Technology"BRFFR-BIT-2020(No.BITBLR2020004)。
文摘The complex micromechanical response among grains remains a persistent challenge to understand the deformation mechanism of titanium alloys during cold rolling.Therefore,in this work,a multiscale crystal plasticity finite element method of dual-phase alloy was proposed and secondarily developed based on LS-DYNA software.Afterward,the texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr alloy,based on the realistic 3D microstructure,during cold rolling(20%thickness reduction)were systematically investigated.The relative activity of the■slip system in theαphase gradually increased,and then served as the main slip mode at lower Schmid factor(<0.2).In contrast,the contribution of the■slip system to the overall plastic deformation was relatively limited.For theβphase,the relative activity of the<111>{110}slip system showed an upward tendency,indicating the important role of the critical resolved shear stress relationship in the relative activity evolutions.Furthermore,the abnormally high strain of very fewβgrains was found,which was attributed to their severe rotations compelled by the neighboring pre-deformedαgrains.The calculated pole figures,rotation axes,and compelled rotation behavior exhibited good agreement to the experimental results.
文摘The most critical issue in the steel catenary riser design is to evaluate the fatigue damage in the touchdown zone accurately. Appropriate modeling of the riser-soil resistance in the touchdown zone can lead to significant cost reduction by optimizing design. This paper presents a plasticity model that can be applied to numerically simulate riser-soil interaction and evaluate dynamic responses and the fatigue damage of a steel catenary riser in the touchdown zone. Utilizing the model, numerous riser-soil elements are attached to the steel catenary riser finite elements, in which each simulates local foundation restraint along the riser touchdown zone. The riser-soil interaction plasticity model accounts for the behavior within an allowable combined loading surface. The model will be represented in this paper, allowing simple numerical implementation. More importantly, it can be incorporated within the structural analysis of a steel catenary riser with the finite element method. The applicability of the model is interpreted theoretically and the results are shown through application to an offshore 8.625 steel catenary riser example. The fatigue analysis results of the liner elastic riser-soil model are also shown. According to the comparison results of the two models, the fatigue life analysis results of the plasticity framework are reasonable and the horizontal effects of the riser-soil interaction can be included.
基金Sponsored by Changjiang Scholars Program of China (Grant No.2009-37)PhD Programs Foundation of Ministry of Education of China (Grant No.20092302110046)Natural Science Foundation of Heilongjiang Province (Grant No.E200916)
文摘This paper establishes an anisotropic plastic material model to analyze the elasto-plastic behavior of masonry in plane stress state.Being an anisotropic material,masonry has different constitutive relation and fracture energies along each orthotropic axes.Considering the unique material properties of masonry,a new yield criterion for masonry is proposed combining the Hill's yield criterion and the Rankine's yield criterion.The new yield criterion not only introduces compression friction coefficient of shear but also considers yield functions for independent stress state along two material axes of tension.To solve the involved nonlinear equations in numerical analysis,several nonlinear methods are implemented,including Newton-Raphson method for nonlinear equations and Implicit Euler backward mapping algorithm to update stresses.To verify the proposed material model of masonry,a series of tests are operated.The simulation results show that the new developed material model implements successfully.Compared with isotropic material model,the proposed model performs better in elasto-plastic analysis of masonry in plane stress state.The proposed anisotropic model is capable of simulating elasto-plastic behavior of masonry and can be used in related applications.
文摘Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high purity aluminum by ECAE at ambient temperature. The experimental results showed that high strain rate and large deformation could induce dynamic recrystallization.Based on dislocation dynamics and grain orientation change enhanced by plastic deformation,a model for the recrystallization process is developed. The model is used to explain the ultra fine grains which are formed at a temperature still much lower than that for the conventional recrystallization
