In 5G systems, massive multiple-input multiple-output (MIMO) has been adopted in base stations (BSs) to improve spectral efficiency and coverage. The traditional conductive performance test techniques are challenging ...In 5G systems, massive multiple-input multiple-output (MIMO) has been adopted in base stations (BSs) to improve spectral efficiency and coverage. The traditional conductive performance test techniques are challenging due to the unaffordable cost and high complexity when testing a large number of antennas. To solve this problem, the over-the-air (OTA) test has been presented, in which probe selection is the key to reduce the number of channel emulators and probes. In this paper, a novel artificial bee colony (ABC) algorithm is introduced to enhance the efficiency and accuracy of probe selection procedure. A sectoring- based multi-probe anechoic chamber (MPAC) is built to evaluate the throughput performance of massive MIMO equipped in 5G BS. In addition, link level simulation is carried out to evaluate the proposal’s performance gain under the commercial network assumptions, where the average throughput of three velocity is given with different SNR region. The results suggest that OTA chamber and multi-probe wall are available not only for 5G BSs, but also for user equipments (UEs) with end-to-end communication.展开更多
Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of c...Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of coin-tap are classified through the grey clustering based on relation analysis,and corresponding improvements are made to the calculation method of the relation degree of nearness.First,the time history of acceleration is taken as the system behavior sequence.The improved correlation calculation method is used to solve the relation degree of nearness between the sequences,and the matrix of degree of grey relation is constructed based on this.Then,the sequence groups are summarized through the matrix,and the response signals of coin-tap are qualitatively classified according to the location of the reference sequence.Finally,the defect detection of composite materials is completed without pre-testing.The test results show that the accuracy of the coin-tap test based on improved grey clustering reaches 100%,which simplifies the operation steps while ensuring the reliability of the coin-tap test results.展开更多
To date,the primary industrial carbon capture approach is still absorption using aqueous solutions of alkanolamines.Here,to pursue a substitute for the amine-based approach to improve the CO_(2) capture efficiency and...To date,the primary industrial carbon capture approach is still absorption using aqueous solutions of alkanolamines.Here,to pursue a substitute for the amine-based approach to improve the CO_(2) capture efficiency and decrease the energy cost further,we report a new carbon capture approach using a 2-methylimidazole(mIm)aqueous solution.The properties and sorption behaviors of this approach have been experimentally investigated.The results show that the mIm solution has higher CO_(2) absorption capacity under relatively higher equilibrium pressure(>130 kPa)and lower desorption heat than the methyldiethanolamine solution.91.6%sorption capacity of mIm solution can be recovered at 353.15 K and 80 kPa.The selectivity for CO_(2)/N_(2) and CO_(2)/CH_(4) can reach an exceptional 7609 and 4324,respectively.Furthermore,the pilot-scale tests were also performed,and the results demonstrate that more than 98%of CO_(2) in the feed gas could be removed and cyclic absorption capacity can reach 1 mol·L^(-1).This work indicates that mIm is an excellent alternative to alkanolamines for carbon capture in the industry.展开更多
Robustness testing for safety-critical embedded software is still a challenge in its nascent stages. In this paper, we propose a practical methodology and implement an environment by employing model-based robustness t...Robustness testing for safety-critical embedded software is still a challenge in its nascent stages. In this paper, we propose a practical methodology and implement an environment by employing model-based robustness testing for embedded software systems. It is a system-level black-box testing approach in which the fault behaviors of embedded software is triggered with the aid of modelbased fault injection by the support of an executable model-driven hardware-in-loop （HIL） testing environment. The prototype implementation of the robustness testing environment based on the proposed approach is experimentally discussed and illustrated by industrial case studies based on several avionics-embedded software systems. The results show that our proposed and implemented robustness testing method and environment are effective to find more bugs, and reduce burdens of testing engineers to enhance efficiency of testing tasks, especially for testing complex embedded systems.展开更多
Unified modeling language （UML） is a powerful graphical modeling language with intuitional meaning. It provides various diagrams to depict system characteristics and complex environment from different viewpoints and...Unified modeling language （UML） is a powerful graphical modeling language with intuitional meaning. It provides various diagrams to depict system characteristics and complex environment from different viewpoints and different application layers. UML-based software development and modeling environments have been widely accepted in industry, including areas in which safety is an important issue such as spaceflight, defense, automobile, etc. To ensure and improve software quality becomes a main concern in the field. As one of the key techniques for software quality, software testing can effectively detect system faults. UML based software testing based is an important research direction in software engineering. The key to software testing is the generation of test cases. This dissertation studies an approach to generating test cases from UML statecharts.展开更多
In this paper,a novel component based framework of test system is presented for the new requirements of dynamic changes of test functions and reconfiguration of test resources.The complexity of dynamic reconfiguration...In this paper,a novel component based framework of test system is presented for the new requirements of dynamic changes of test functions and reconfiguration of test resources.The complexity of dynamic reconfiguration arises from the scale,redirection,extensibility and interconnection of components in test system.The paper is started by discussing the component assem-bly based framework which provide the open platform to the deploy of companents and then the script interpreter model is introduced to dynamically create the components and build the test system by analyzing XML based information of test system.A pipeline mod-el is presented to provide the data channels and behavior reflection among the components.Finally,a dynamic reconfigurable test system is implemented on the basis of COM and applied in the remote test and control system of CNC machine.展开更多
Studies on Soil Test Crop Response Based Integrated Plant Nutrition System(STCR-IPNS)were conducted for three years adopting the Inductive cum Targeted Yield Model,on alfisols of Unified Andhra Pradesh,Southern India ...Studies on Soil Test Crop Response Based Integrated Plant Nutrition System(STCR-IPNS)were conducted for three years adopting the Inductive cum Targeted Yield Model,on alfisols of Unified Andhra Pradesh,Southern India during summer 2016-2018 in order to develop fertilizer prescriptions through IPNS for the desired yield targets of Sesamum under field conditions.The bases for making the fertilizer prescriptions viz.nutrient requirement(NR),contribution of nutrients from soil(Cs),fertilizer(Cf)and vermicompost(CVC)were computed using the field experimental data.Making use of these basic parameters,the fertilizer prescription equations were developed under NPK alone and under IPNS for the desired yield targets of Sesamum for a range of soil test values.The quantity of fertilizers contributed by the application of vermicompost was assessed.Nutrient requirement to produce 100 kg of sesame seed was worked out to be 10.20 kg N,3.90 kg P2O5 and 5.22 kg K2O.In the present investigation,the requirement of N was higher which is followed by K2O and P2O5.The requirement of N was 2.62 times higher than P and 1.95 times higher than K.The percent contribution of N,P and K was 12.25,15.75 and 6.00 from soils,41.68,22.85 and 59.97 from fertilizer and 9.87,6.74 and 18.65 from organic manures,respectively.Thus the Inductive cum Targeted Yield Model used to develop fertilizer prescription equations provides a strong basis for soil fertility maintenance consistent with high productivity and efficient nutrient management in farming for sustainable and enduring agriculture.展开更多
Compressive strength and compressive resilience modulus are two important parameters to measure the mechanical properties of semi-rigid base.The test methods of semi-rigid base cores are different from those of the la...Compressive strength and compressive resilience modulus are two important parameters to measure the mechanical properties of semi-rigid base.The test methods of semi-rigid base cores are different from those of the laboratory samples in terms of sample acquisition,sample selection and humidity requirements.Core-drilling location,size of core sample,smoothness and humidity conditions were analyzed.The test methods of compressive strength and compressive resilience modulus were proposed.The research results show that compressive strength of lime fly-ash stabilized gravels base has a tendency of increasing during a long period.The compressive resilience modulus increases significantly with compressive strength of semi-rigid base.The compressive resilience modulus generally is 3-4 times than the recommended range of asphalt pavement design specifications.The fluctuation range of compressive resilience modulus is obviously higher than the compressive strength.The compressive resilience modulus is more sensitive to the construction variability.The overall trend between the compressive resilience modulus and the back-calculation modulus is consistent.FWD(falling weight deflectometer)back-calculation modulus can reflect the stiffness and bearing capacity of asphalt pavement.展开更多
Quality of software systems is highly demanded in today’s scenario. Highly testable system enhances the reliability also. More than 50% of test effort-time and cost are used to produce a highly testable system. Thus,...Quality of software systems is highly demanded in today’s scenario. Highly testable system enhances the reliability also. More than 50% of test effort-time and cost are used to produce a highly testable system. Thus, design-for-testability is needed to reduce the test effort. In order to enhance the quality, productivity and reduced cost of the software organizations are promoting to produce the reuse-oriented products. Incorporating reuse technology in both aspects-software development process and test process may payoff many folds. Keeping this view, our study focus the testability of the object-oriented framework based software systems and identify that flexibility at the variable points of the object-oriented framework, chosen for framework instantiation, greatly affects the testability of object-oriented framework based software at each level of testing. In the current paper, we propose a testability model considering the flexible aspect of the variable point to estimate testability in the early phase, requirement analysis phase, of development process of the framework based software. The proposed model helps to improve the testability of the software before the implementation starts thus reducing the overall development cost.展开更多
The function of the UHVDC test base of the State Grid Corporation of China (SGCC) is oriented to serve UHVDC power transmission and substation projects, especially power transmission from West China to East China, and...The function of the UHVDC test base of the State Grid Corporation of China (SGCC) is oriented to serve UHVDC power transmission and substation projects, especially power transmission from West China to East China, and to promote localization of UHVDC transmission and substation equipment. In essentials, this test base consists of UHVDC test transmission line, corona cage, outdoor test site, UHV test hall, pollution and environment laboratory, electromagnetic environment simulation test site, insulator laboratory, arrester laboratory and live equipment test field. This paper introduces the function and design idea of the test base, presents the main performance parameters of the above-mentioned test facilities, and summarizes the matters of concern when siting and planning.展开更多
The construction of the UHVAC test base of SGCC is an important component of the pilot project on UHVAC power transmission and transformation in China. This paper introduces the layout, technical requirements and main...The construction of the UHVAC test base of SGCC is an important component of the pilot project on UHVAC power transmission and transformation in China. This paper introduces the layout, technical requirements and main test functions of the UHVAC test base as well as difficulties during construction. It lays stress on the characterization of a 1 000-kV single-circuit test line, a 1 000-kV one-tower double-circuit test line, a full voltage test site for UHV equipment, a climate laboratory, a corona cage and a long-wave-front impulse voltage generator.展开更多
The tarnishing test in the presence of hydrogen sulfide（H2S） vapors has been used to investigate the tarnish resistance capability of copper-based alloys coated with Si02-like films by means of plasma-enhanced chemi...The tarnishing test in the presence of hydrogen sulfide（H2S） vapors has been used to investigate the tarnish resistance capability of copper-based alloys coated with Si02-like films by means of plasma-enhanced chemical vapor deposition（PECVD） fed with a tetraethoxysilane/oxygen mixture.The chemical and morphological properties of the films have been characterized by using infrared absorption spectroscopy（IR） and scanning electron microscopy（SEM）with energy disperse spectroscopy（EDS）.The corrosion products of the samples after the tarnishing test have been identified by X-ray diffraction analysis（XRD）.It has been found that SiO2-like films formed via PECVD with a high O2 flow rate could protect copper-based alloys from H2S vapor tarnishing.The alloys coated at the O2 flow rate of 20 sccm remain uncorroded after 54days of H2S vapor tarnish testing.The corrosion products for the alloys deposited at a low O2flow rate after 54 days of tarnish testing are mainly composed of brochantite.展开更多
The essay aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vocational college, with the further purpose to work out some ways to promote positive washback effect and reform t...The essay aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vocational college, with the further purpose to work out some ways to promote positive washback effect and reform the current tests hence to improve vocational learning.展开更多
The present study aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vo cational college, with the further purpose to work out some ways to promote positive washback effect and...The present study aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vo cational college, with the further purpose to work out some ways to promote positive washback effect and reform the current tests hence to improve vocational teaching.展开更多
Globally, traditional power systems are rapidly transforming towards the adoption of smart grid platforms. Substations which are at the center of the electric power transformation from the power plant are changing to ...Globally, traditional power systems are rapidly transforming towards the adoption of smart grid platforms. Substations which are at the center of the electric power transformation from the power plant are changing to IEC 61850 based digital substations. Therefore, within substation, there is a growing demand for the IEC 61850 based Intelligent Electronic Devices (IEDs). The operation of multiple manufacturers of IEDs in a single digital substation network increases the need for IEC 61850 communications specification conformance diagnosis to ensure interoperability for efficient data exchange between IEDs. The IEC 61850-10 presents test items for diagnosing communication specification conformance. There are many test tools available in the market today to test the compliance of the IEC 61850 communications specifications to the IED. In this paper, we propose a model-based diagnostic method for IED communication conformance testing. The proposed model-based software therefore uses the “drag and drop” technique to select the various IEC 61850 communication services (objects) required to design the test case in a user friendly Graphical User Interface (GUI). This makes the service conformance testing more flexible for test engineers and system integrators especially in situations that require test case modifications. Also, the proposed software tool makes it easy to understand the various IEC 61850 services using the friendly GUI.展开更多
Parallel key-insulation allows the use of multiple helper keys to protect private decryption keys during secret decryption key updates. This approach prevents decryption key leakage or exposure in insecure environment...Parallel key-insulation allows the use of multiple helper keys to protect private decryption keys during secret decryption key updates. This approach prevents decryption key leakage or exposure in insecure environment. We combined parallel key-insulated encryption (PKIE) with multiple helper keys and identity-based encryption with the equality test (IBE-ET) to obtain parallel key insulated ID-based public key encryption with outsourced equivalent test (PKI-IBPKE-ET). The scheme inherits the advantages of identity-based encryption (IBE), which simplifies certificate management for public key encryption. Furthermore, the parallel key-insulation with multiple helper mechanism was introduced in our scheme, which perfectly reduced the possibility of helper key exposure. Our scheme will enable the protection and periodic update of decryption keys in insecure environment. Our scheme achieves a weak indistinguishable identity chosen ciphertext (W-IND-ID-CCA) security in the random oracle model. Ultimately, it is observed that our scheme is feasible and practical through the experimental simulation and theoretical analysis.展开更多
In a component-based software development life cycle, selection of preexisting components is an important task. Every component that has to be reused has an associated risk of failure of not meeting the functional and...In a component-based software development life cycle, selection of preexisting components is an important task. Every component that has to be reused has an associated risk of failure of not meeting the functional and non-functional requirements. A component's failure would lead a developer to look for some other alternative of combinations of COTS, in-house and engineered components among possible candidate combinations. This means design itself can readily change. The very process of design of a software system and component selection seems to be heavily dependent on testing results. Instability of design, further, becomes more severe due to requirements change requests. Therefore, this instability of design has to be essentially mitigated by using proper design and testing approaches, otherwise, it may lead to exorbitantly high testing cost due to the repeated testing of various alternatives. How these three activities: Component-based software design, component selection and component-based software testing are interrelated? What process model is most suited to address this concern? This work explores the above questions and their implication in terms of nature of a process model that can be convincing in case of component-based software development.展开更多
基金supported by the State Major Science and Technology Special Projects under Grant No. 2018ZX03001028-003
文摘In 5G systems, massive multiple-input multiple-output (MIMO) has been adopted in base stations (BSs) to improve spectral efficiency and coverage. The traditional conductive performance test techniques are challenging due to the unaffordable cost and high complexity when testing a large number of antennas. To solve this problem, the over-the-air (OTA) test has been presented, in which probe selection is the key to reduce the number of channel emulators and probes. In this paper, a novel artificial bee colony (ABC) algorithm is introduced to enhance the efficiency and accuracy of probe selection procedure. A sectoring- based multi-probe anechoic chamber (MPAC) is built to evaluate the throughput performance of massive MIMO equipped in 5G BS. In addition, link level simulation is carried out to evaluate the proposal’s performance gain under the commercial network assumptions, where the average throughput of three velocity is given with different SNR region. The results suggest that OTA chamber and multi-probe wall are available not only for 5G BSs, but also for user equipments (UEs) with end-to-end communication.
基金National Key Research and Development Project of China(No.2018YFB1701200)。
文摘Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of coin-tap are classified through the grey clustering based on relation analysis,and corresponding improvements are made to the calculation method of the relation degree of nearness.First,the time history of acceleration is taken as the system behavior sequence.The improved correlation calculation method is used to solve the relation degree of nearness between the sequences,and the matrix of degree of grey relation is constructed based on this.Then,the sequence groups are summarized through the matrix,and the response signals of coin-tap are qualitatively classified according to the location of the reference sequence.Finally,the defect detection of composite materials is completed without pre-testing.The test results show that the accuracy of the coin-tap test based on improved grey clustering reaches 100%,which simplifies the operation steps while ensuring the reliability of the coin-tap test results.
基金The financial supports received from National Natural Science Foundation of China (U20B6005, 22178378, and 22127812)
文摘To date,the primary industrial carbon capture approach is still absorption using aqueous solutions of alkanolamines.Here,to pursue a substitute for the amine-based approach to improve the CO_(2) capture efficiency and decrease the energy cost further,we report a new carbon capture approach using a 2-methylimidazole(mIm)aqueous solution.The properties and sorption behaviors of this approach have been experimentally investigated.The results show that the mIm solution has higher CO_(2) absorption capacity under relatively higher equilibrium pressure(>130 kPa)and lower desorption heat than the methyldiethanolamine solution.91.6%sorption capacity of mIm solution can be recovered at 353.15 K and 80 kPa.The selectivity for CO_(2)/N_(2) and CO_(2)/CH_(4) can reach an exceptional 7609 and 4324,respectively.Furthermore,the pilot-scale tests were also performed,and the results demonstrate that more than 98%of CO_(2) in the feed gas could be removed and cyclic absorption capacity can reach 1 mol·L^(-1).This work indicates that mIm is an excellent alternative to alkanolamines for carbon capture in the industry.
基金the Aeronautics Science Foundation of China(No.2011ZD51055)Science and Technology on Reliability&Environmental Engineering Laboratory(No.302367)the National Pre-Research Foundation of China(No.51319080201)
文摘Robustness testing for safety-critical embedded software is still a challenge in its nascent stages. In this paper, we propose a practical methodology and implement an environment by employing model-based robustness testing for embedded software systems. It is a system-level black-box testing approach in which the fault behaviors of embedded software is triggered with the aid of modelbased fault injection by the support of an executable model-driven hardware-in-loop （HIL） testing environment. The prototype implementation of the robustness testing environment based on the proposed approach is experimentally discussed and illustrated by industrial case studies based on several avionics-embedded software systems. The results show that our proposed and implemented robustness testing method and environment are effective to find more bugs, and reduce burdens of testing engineers to enhance efficiency of testing tasks, especially for testing complex embedded systems.
文摘Unified modeling language （UML） is a powerful graphical modeling language with intuitional meaning. It provides various diagrams to depict system characteristics and complex environment from different viewpoints and different application layers. UML-based software development and modeling environments have been widely accepted in industry, including areas in which safety is an important issue such as spaceflight, defense, automobile, etc. To ensure and improve software quality becomes a main concern in the field. As one of the key techniques for software quality, software testing can effectively detect system faults. UML based software testing based is an important research direction in software engineering. The key to software testing is the generation of test cases. This dissertation studies an approach to generating test cases from UML statecharts.
基金Supported by the National Science Foundation of China(Grant No.50275061)the National High Technology Research and Development Program(Grant No.2001AA423230).
文摘In this paper,a novel component based framework of test system is presented for the new requirements of dynamic changes of test functions and reconfiguration of test resources.The complexity of dynamic reconfiguration arises from the scale,redirection,extensibility and interconnection of components in test system.The paper is started by discussing the component assem-bly based framework which provide the open platform to the deploy of companents and then the script interpreter model is introduced to dynamically create the components and build the test system by analyzing XML based information of test system.A pipeline mod-el is presented to provide the data channels and behavior reflection among the components.Finally,a dynamic reconfigurable test system is implemented on the basis of COM and applied in the remote test and control system of CNC machine.
基金This work was carried out under part of AICRP on Soil Test Crop Response,ICAR at PJTSAU,Hyderabad-500030,India.
文摘Studies on Soil Test Crop Response Based Integrated Plant Nutrition System(STCR-IPNS)were conducted for three years adopting the Inductive cum Targeted Yield Model,on alfisols of Unified Andhra Pradesh,Southern India during summer 2016-2018 in order to develop fertilizer prescriptions through IPNS for the desired yield targets of Sesamum under field conditions.The bases for making the fertilizer prescriptions viz.nutrient requirement(NR),contribution of nutrients from soil(Cs),fertilizer(Cf)and vermicompost(CVC)were computed using the field experimental data.Making use of these basic parameters,the fertilizer prescription equations were developed under NPK alone and under IPNS for the desired yield targets of Sesamum for a range of soil test values.The quantity of fertilizers contributed by the application of vermicompost was assessed.Nutrient requirement to produce 100 kg of sesame seed was worked out to be 10.20 kg N,3.90 kg P2O5 and 5.22 kg K2O.In the present investigation,the requirement of N was higher which is followed by K2O and P2O5.The requirement of N was 2.62 times higher than P and 1.95 times higher than K.The percent contribution of N,P and K was 12.25,15.75 and 6.00 from soils,41.68,22.85 and 59.97 from fertilizer and 9.87,6.74 and 18.65 from organic manures,respectively.Thus the Inductive cum Targeted Yield Model used to develop fertilizer prescription equations provides a strong basis for soil fertility maintenance consistent with high productivity and efficient nutrient management in farming for sustainable and enduring agriculture.
文摘Compressive strength and compressive resilience modulus are two important parameters to measure the mechanical properties of semi-rigid base.The test methods of semi-rigid base cores are different from those of the laboratory samples in terms of sample acquisition,sample selection and humidity requirements.Core-drilling location,size of core sample,smoothness and humidity conditions were analyzed.The test methods of compressive strength and compressive resilience modulus were proposed.The research results show that compressive strength of lime fly-ash stabilized gravels base has a tendency of increasing during a long period.The compressive resilience modulus increases significantly with compressive strength of semi-rigid base.The compressive resilience modulus generally is 3-4 times than the recommended range of asphalt pavement design specifications.The fluctuation range of compressive resilience modulus is obviously higher than the compressive strength.The compressive resilience modulus is more sensitive to the construction variability.The overall trend between the compressive resilience modulus and the back-calculation modulus is consistent.FWD(falling weight deflectometer)back-calculation modulus can reflect the stiffness and bearing capacity of asphalt pavement.
文摘Quality of software systems is highly demanded in today’s scenario. Highly testable system enhances the reliability also. More than 50% of test effort-time and cost are used to produce a highly testable system. Thus, design-for-testability is needed to reduce the test effort. In order to enhance the quality, productivity and reduced cost of the software organizations are promoting to produce the reuse-oriented products. Incorporating reuse technology in both aspects-software development process and test process may payoff many folds. Keeping this view, our study focus the testability of the object-oriented framework based software systems and identify that flexibility at the variable points of the object-oriented framework, chosen for framework instantiation, greatly affects the testability of object-oriented framework based software at each level of testing. In the current paper, we propose a testability model considering the flexible aspect of the variable point to estimate testability in the early phase, requirement analysis phase, of development process of the framework based software. The proposed model helps to improve the testability of the software before the implementation starts thus reducing the overall development cost.
文摘The function of the UHVDC test base of the State Grid Corporation of China (SGCC) is oriented to serve UHVDC power transmission and substation projects, especially power transmission from West China to East China, and to promote localization of UHVDC transmission and substation equipment. In essentials, this test base consists of UHVDC test transmission line, corona cage, outdoor test site, UHV test hall, pollution and environment laboratory, electromagnetic environment simulation test site, insulator laboratory, arrester laboratory and live equipment test field. This paper introduces the function and design idea of the test base, presents the main performance parameters of the above-mentioned test facilities, and summarizes the matters of concern when siting and planning.
文摘The construction of the UHVAC test base of SGCC is an important component of the pilot project on UHVAC power transmission and transformation in China. This paper introduces the layout, technical requirements and main test functions of the UHVAC test base as well as difficulties during construction. It lays stress on the characterization of a 1 000-kV single-circuit test line, a 1 000-kV one-tower double-circuit test line, a full voltage test site for UHV equipment, a climate laboratory, a corona cage and a long-wave-front impulse voltage generator.
基金supported by the Special Fund for Talent of Wuhan Institute of Technology,China(No.237127)the"Fellowship for Junior Researchers"from Politecnico di Torino and Regione Piemonte,Italy
文摘The tarnishing test in the presence of hydrogen sulfide（H2S） vapors has been used to investigate the tarnish resistance capability of copper-based alloys coated with Si02-like films by means of plasma-enhanced chemical vapor deposition（PECVD） fed with a tetraethoxysilane/oxygen mixture.The chemical and morphological properties of the films have been characterized by using infrared absorption spectroscopy（IR） and scanning electron microscopy（SEM）with energy disperse spectroscopy（EDS）.The corrosion products of the samples after the tarnishing test have been identified by X-ray diffraction analysis（XRD）.It has been found that SiO2-like films formed via PECVD with a high O2 flow rate could protect copper-based alloys from H2S vapor tarnishing.The alloys coated at the O2 flow rate of 20 sccm remain uncorroded after 54days of H2S vapor tarnish testing.The corrosion products for the alloys deposited at a low O2flow rate after 54 days of tarnish testing are mainly composed of brochantite.
文摘The essay aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vocational college, with the further purpose to work out some ways to promote positive washback effect and reform the current tests hence to improve vocational learning.
文摘The present study aims at revealing the washback effect of task-based communicative language test(TBCLT) in a vo cational college, with the further purpose to work out some ways to promote positive washback effect and reform the current tests hence to improve vocational teaching.
文摘Globally, traditional power systems are rapidly transforming towards the adoption of smart grid platforms. Substations which are at the center of the electric power transformation from the power plant are changing to IEC 61850 based digital substations. Therefore, within substation, there is a growing demand for the IEC 61850 based Intelligent Electronic Devices (IEDs). The operation of multiple manufacturers of IEDs in a single digital substation network increases the need for IEC 61850 communications specification conformance diagnosis to ensure interoperability for efficient data exchange between IEDs. The IEC 61850-10 presents test items for diagnosing communication specification conformance. There are many test tools available in the market today to test the compliance of the IEC 61850 communications specifications to the IED. In this paper, we propose a model-based diagnostic method for IED communication conformance testing. The proposed model-based software therefore uses the “drag and drop” technique to select the various IEC 61850 communication services (objects) required to design the test case in a user friendly Graphical User Interface (GUI). This makes the service conformance testing more flexible for test engineers and system integrators especially in situations that require test case modifications. Also, the proposed software tool makes it easy to understand the various IEC 61850 services using the friendly GUI.
文摘Parallel key-insulation allows the use of multiple helper keys to protect private decryption keys during secret decryption key updates. This approach prevents decryption key leakage or exposure in insecure environment. We combined parallel key-insulated encryption (PKIE) with multiple helper keys and identity-based encryption with the equality test (IBE-ET) to obtain parallel key insulated ID-based public key encryption with outsourced equivalent test (PKI-IBPKE-ET). The scheme inherits the advantages of identity-based encryption (IBE), which simplifies certificate management for public key encryption. Furthermore, the parallel key-insulation with multiple helper mechanism was introduced in our scheme, which perfectly reduced the possibility of helper key exposure. Our scheme will enable the protection and periodic update of decryption keys in insecure environment. Our scheme achieves a weak indistinguishable identity chosen ciphertext (W-IND-ID-CCA) security in the random oracle model. Ultimately, it is observed that our scheme is feasible and practical through the experimental simulation and theoretical analysis.
文摘In a component-based software development life cycle, selection of preexisting components is an important task. Every component that has to be reused has an associated risk of failure of not meeting the functional and non-functional requirements. A component's failure would lead a developer to look for some other alternative of combinations of COTS, in-house and engineered components among possible candidate combinations. This means design itself can readily change. The very process of design of a software system and component selection seems to be heavily dependent on testing results. Instability of design, further, becomes more severe due to requirements change requests. Therefore, this instability of design has to be essentially mitigated by using proper design and testing approaches, otherwise, it may lead to exorbitantly high testing cost due to the repeated testing of various alternatives. How these three activities: Component-based software design, component selection and component-based software testing are interrelated? What process model is most suited to address this concern? This work explores the above questions and their implication in terms of nature of a process model that can be convincing in case of component-based software development.
