MICP(Microbially induced calcite precipitation),an environmentally friendly soil improvement technique,has great potential in ocean engineering due to its ability to promote the precipitation of calcium carbonate thro...MICP(Microbially induced calcite precipitation),an environmentally friendly soil improvement technique,has great potential in ocean engineering due to its ability to promote the precipitation of calcium carbonate through microbial activity to enhance the engineering properties of geomaterials.In this study,piezocone penetration test(CPTU)is used to evaluate the effectiveness of MICP treatment in calcareous sand.The change of physical properties(relative density D and total unit weight)of MICP treated calcareous sand is investigated by conducting CPTU on the geomaterials prepared in a series of mini calibration chambers(25 cm×50 cm).Results indicate that CPTU(tip stress,sleeve friction,and porewater pressure)measurements can be used to interpret the physical characteristics of calcareous sand treated with MICP under seawater conditions.Additionally,a relationship between CPTU measurements,physical parameters(relative density D,and total unit weight y)of MICP treated calcareous sand is proposed and calibrated.The findings of the research extend the implementation of in-situ testing techniques such as CPTU towards physical property evaluation of bio-treated geomaterials in ocean environment,and demonstrate the potential of scaling up MICP techniques for broader engineeringapplication.展开更多
The vast area of farmland was abandoned at downstream of the Shiyang River because of decreased water recourse. To ensure the ecological safety of Minqin Oasis and to provide management basis for the abandoned land, s...The vast area of farmland was abandoned at downstream of the Shiyang River because of decreased water recourse. To ensure the ecological safety of Minqin Oasis and to provide management basis for the abandoned land, soil physical properties were observed and studied. The authors analyzed land with abandonment time of 1 year, 2 years, 3 years, 4 years, 5 years, 8 years, 15 years, 24 years and 31 years. Samples were took at the 0-40 cm layer of soil to measure the bulk density, porosity and grain composition of soil in the different abandoned lands. Results showed that the tendency of clay content was decreasing, conversely, the fine sand increased at the layer of 0-10 cm of different abandoned lands.The changes of grain content reached a peak at the fourth year after the land was abandoned, then varied slightly. The variation of grain content of abandoned land was obvious with the extension of the abandonment year. The soil bulk density decreased and porosity increased with the extension of the abandonment year. The difference of porosity and soil bulk density at the range of 0-40 cm of different abandoned land decreased after the land abandoned for 3 years. The quality of soil was decreased, while the soil permeability was improved. The soil physical properties changed obviously in 3 to 4 years after abandonment, so it is the key time for land management.展开更多
We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are succ...We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are success- fully obtained. The measurement of temperature dependence of electricaJ resistivity p（T） in both normal and superconducting states indicates a quasi-two-dimensional electronic state in contrast to that of polycrystalline samples. Specific heat C（T） measurement reveals a bulk superconductivity with Tc ≈ 3.75K and a specific heat jump ratio of 1.42. All these results are in agreement with a moderately electron-phonon coupled, type-g Bardeen-Cooper-Schrieffer superconductor.展开更多
2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into...2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into con-sideration. The result shows that: 1) Average crustal velocity ratio is obviously higher in Tarim block than in West Kunlun Mts. and Tianshan fold zone, which reflects its crustal physical property of 'hardness' and stability. The relatively low but normai velocity ratio (Poisson's ratio) of the lower crust indicates that the 'downward thrusting' of Tarim basin is the main feature of crustal movement in this area. 2) The rock layer in the upper crust of Tianshan fold zone is relatively 'soft', which makes it prone to rupture and stress energy release. This is the primary tectonic factor for the concentration of small earthquakes in this area. 3) Jiashi is located right over the apex or the inflection point of the updoming lower crustal interface C and the crust-mantle boundary, which is the deep struc-tural background for the occurrence of strong earthquakes. The alternate variation of vp/vs near the block bounda-ries and the complicated configuration of the interfaces in the upper and middie part of the upper crust form a par-ticular structural environment for the Jiashi strong earthquake swarm. vp/vs is comparatively high and shear modulus is low at the focal region, which may be the main reason for the low stress drop of the Jiashi strong earthquake swarm.展开更多
From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the...From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the physical propenies of the slag and the mass action concentrations of its have been set up at certain temperature and slag composition range, which based on the thermodynamic data of the chemtical reactions between the units and the method of linear regression. The calculated data from the model are in good agreement with the measured results. These calculated values are more accurate and systematic than those from other expirical and semi-expirical formulas used at present.展开更多
In this work,multiple molecular dynamics simulations of protein G and protein L unfolding trajectories provide a direct demonstration of the diversity of unfolding pathway and give a statistically utmost unfolding pat...In this work,multiple molecular dynamics simulations of protein G and protein L unfolding trajectories provide a direct demonstration of the diversity of unfolding pathway and give a statistically utmost unfolding pathway under the physical property space.展开更多
The Liushagang Formation in the Weixinan Depression,Beibu Gulf Basin,southern China,is one of the key stratigraphic units for offshore shale oil exploration in the country.The shale oil reservoirs in the formation are...The Liushagang Formation in the Weixinan Depression,Beibu Gulf Basin,southern China,is one of the key stratigraphic units for offshore shale oil exploration in the country.The shale oil reservoirs in the formation are characterized by low porosity,low permeability and strong heterogeneity,which constrain the precise evaluation of reservoir properties,the accurate prediction of sweet spots,and efficient development.This study integrates core observation,mineralogical analysis,and multi-scale pore characterization to systematically clarify the variations in reservoir properties and their controlling mechanisms.The results show that the physical properties of matrix-type,lamina-type,and interlayer-type reservoirs exhibit distinct stepwise variations:Among these,interlayer-type reservoirs show the greatest development potential(quartz content 65%,average porosity 15%,permeability>10 mD,and mobile fluid saturation 60%),whereas matrix-type reservoirs are the least favorable(dominated by 40 nm nanoscale pores,and clay content 45%).Mineral composition,sedimentary-diagenetic processes,and fault systems collectively control reservoir property heterogeneity.Quartz-rich rigid frameworks resist compaction,resulting in a porosity increase by approximately 2% for every 10%rise in q uartz content.The transformation of clay minerals induces stratified porosity zoning within the layered reservoirs,while fault systems enhance heterogeneity through the development of fracture networks and acid-induced dissolution.This study provides theoretical support for the evaluation and development of shale oil sweet spots in the Weixinan Depression and holds practical significance for the commercial development of shale oil in China's offshore areas.展开更多
To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agric...To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agricultural Experimental Station of Chinese Academy Sciences in the Low Plain of the North China Plain,comprising four irrigation treatments:irrigation once at the jointing stage for winter wheat with irrigation water containing salt at fresh water,3,4 and 5 g·L^(–1),and maize irrigation at sowing using fresh water.Manure application was conducted under all irrigation treatments,with treatments without manure application used as controls.The results showed that under long-term irrigation with saline water,the application of manure increased the soil organic matter content,exchangeable potassium,available phosphorus,and total nitrogen content in the 0–20 cm soil layer by 46.8%,117.0%,75.7%,and 45.5%,respectively,compared to treatments without manure application.The application of manure reduced soil bulk density.It also increased the proportion of water-stable aggregates and the abundance of bacteria,fungi,and actinomycetes in the tillage soil layer compared to the controls.Because of the salt contained in the manure,the application of manure had dual effects on soil salt content.During the winter wheat season,manure application increased soil salt content.The salt content was significantly reduced during the summer maize season,owing to the strong salt-leaching effects under manure application,resulting in a smaller difference in salt content between the manure and non-manure treatments.During the summer rainfall season,improvements in soil structure under manure application increased the soil desalination rate for the 1 m top soil layer.The desalination rate for 0–40 cm and 40–100 cm was averagely by 39.1%and 18.9%higher,respectively,under manure application as compared with that under the nomanure treatments.The yield of winter wheat under manure application was 0.12%lower than that of the control,owing to the higher salt content during the winter wheat season.In contrast,the yield of summer maize improved by 3.9%under manure application,owing to the increased soil nutrient content and effective salt leaching.The results of this study indicated that manure application helped maintain the soil physical structure,which is important for the long-term use of saline water.In practice,using manure with a low salt content is suggested to reduce the adverse effects of saline water irrigation on soil properties and achieve sustainable saline water use.展开更多
Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field lif...Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field life,part of them has entered the high water cut and high recovery stage.Traditional water flooding way for improving oil recovery becomes more difficult,and new method has to be considered.Maling oilfield BS district is a typical representative,with high water cut of 90.8%,high recovery percent of 26.1%and low oil recovery rate of 0.25%.To explore the new way to improve oil recovery,the polymer and surfactant(SP for short)important pilot test has been developed.The low permeability reservoir indoor core data in high water cut stage and inspection well results indicate that the reservoir permeability,pore combination characteristics and pore type changed greatly after long-term water flooding development.These changes bring more difficulties to the continue development,especially the high injection pressure,which can cause other problems for well pattern infilling and EOR.This paper takes the high injection pressure problem of Maling BS district Jurassic reservoir for example,analyzes the physical property change law on the following aspects:the development mode in the past,core analysis,formation sensitivity,interstitial matter,well test interpretation results,in order to help to further effective development and provide important parameters for tertiary oil recovery technique for similar reservoirs and others.展开更多
Exploring dynamic mechanical responses and failure behaviors of hot dry rock(HDR)is significant for geothermal exploitation and stability assessment.In this study,via the split Hopkinson pressure bar(SHPB)system,a ser...Exploring dynamic mechanical responses and failure behaviors of hot dry rock(HDR)is significant for geothermal exploitation and stability assessment.In this study,via the split Hopkinson pressure bar(SHPB)system,a series of dynamic compression tests were conducted on granite treated by cyclic thermal shocks at different temperatures.We analyzed the effects of cyclic thermal shock on the thermal-related physical and dynamic mechanical behaviors of granite.Specifically,the P-wave velocity,dynamic strength,and elastic modulus of the tested granite decrease with increasing temperature and cycle number,while porosity and peak strain increase.The degradation law of dynamic mechanical properties could be described by a cubic polynomial.Cyclic thermal shock promotes shear cracks propagation,causing dynamic failure mode of granite to transition from splitting to tensile-shear composite failure,accompanied by surface spalling and debris splashing.Moreover,the thermal shock damage evolution and coupled failure mechanism of tested granite are discussed.The evolution of thermal shock damage with thermal shock cycle numbers shows an obvious S-shaped surface,featured by an exponential correlation with dynamic mechanical parameters.In addition,with increasing thermal shock temperature and cycles,granite mineral species barely change,but the length and width of thermal cracks increase significantly.The non-uniform expansion of minerals,thermal shock-induced cracking,and water-rock interaction are primary factors for deteriorating dynamic mechanical properties of granite under cyclic thermal shock.展开更多
Transition metal possesses a unique d-orbital electronic structure,which imparts a diverse range of physical and chemical properties.These properties render them significant in fields such as chemistry and materials s...Transition metal possesses a unique d-orbital electronic structure,which imparts a diverse range of physical and chemical properties.These properties render them significant in fields such as chemistry and materials science.The distinctive optical,electrical,and magnetic properties of these complexes can be attributed to the variations in the quantity of d-orbital electrons,thereby influencing their spin and orbital characteristics.The d-orbitals facilitate the formation of stable multidirectional bonds with ligands,resulting in a variety of geometric structures and rich coordination chemistry.These interactions result in variations in energy levels,thereby producing diverse electrical properties,including low attenuation coefficients,high rectification ratios,and unique multichannel transmission.Moreover,the unpaired electrons inthe d-orbitals can give rise to diverse magnetic behaviors,leading to magnetic effects such as spin-related interfaces,switches,and magnetoresistance.This paves the way for extensive possibilities in the design and application of single-molecule devices.This review elaborates on singlemolecule physical properties of transition metal complexes,including length attenuation,rectification,multi-channel transmission,thermoelectric effect,and spin regulation,which are vital for the functionalization and regulation of molecular electronics.In addition,this review also explores the correlation between these physical properties and the electronic structure of transition metals,discussing the broad prospects of transition metal complexes in the fields of nanoelectronics,optoelectronics,and quantum technology.展开更多
This review aims to identify the assets and limitations of Dabema(Piptadeniastrum africanum)as a sustainable alternative to traditional timber species for furniture and construction applications.Dabema is characterize...This review aims to identify the assets and limitations of Dabema(Piptadeniastrum africanum)as a sustainable alternative to traditional timber species for furniture and construction applications.Dabema is characterized by its high density and dimensional stability,meeting ASTM(American Society for Testing and Materials)standards for mechanical strength,which is essential for promoting its use.However,its limited availability in trade and ingrained habits of use are obstacles to its widespread commercialization.In addition,thermal and oleothermal treatments have shown great potential for improving the characteristics of this wood,although they require ongoing optimization and rigorous environmental assessment.Consequently,increased awareness of the benefits of Dabema is decisive to encourage its sustainable adoption in modern economies.This could help to diversify forest resources and encourage more sustainable building practices,taking advantage of Dabema’s unique properties while mitigating environmental sustainability concerns.展开更多
A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of ...A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of shielding gases with varying He-Ar ratios,and the coupling between arc plasma and laser-induced metal plume.The accuracy of the model is validated using a high-speed camera.The effects of varying He contents in the shielding gas on both the temperature and flow velocity of hybrid plasma,as well as the distribu-tion of laser-induced metal vapor mass,were investigated separately.The maximum temperature and size of arc plasma decrease as the He volume ratio increases,the arc distribution becomes more concentrated,and its flow velocity initially decreases and then sharply increases.At high helium content,both the flow velocity of hybrid plasma and metal vapor are high,the metal vapor is con-centrated on the right side of keyhole,and its flow appears chaotic.The flow state of arc plasma is most stable when the shielding gas consists of 50%He+50%Ar.展开更多
Coral sand is a unique material developed in the tropical ocean environment, which is mainly composed of coral and other marine organism debris, with the CaCO3 content up to 96 %. It has special physical and mechanica...Coral sand is a unique material developed in the tropical ocean environment, which is mainly composed of coral and other marine organism debris, with the CaCO3 content up to 96 %. It has special physical and mechanical properties due to its composition, structure and sedimentary environment. In this contribution, we discuss its specific gravity, porosity ratio compressibility, crushing, shearing and intensity for coral sand samples from the Nansha islands based on laboratory mechanical tests. Our results show distinct high porosity ratio, high friction angle and low intensity as compared with the quartz sand. We believe that grain crushing is the main factor that influences the deformation and strength of coral sand. Comprehensive study on the physical and mechanical properties of coral sands is significant in providing reliable scientific parameters to construction on coral islet, and thus avoids accidents in construction.展开更多
[ Objective] The research aimed to study effects of material physical properties on white-rot fungi mycelial growth and provide theoretical basis for further expanding the application range of white-rot fungi. [ Metho...[ Objective] The research aimed to study effects of material physical properties on white-rot fungi mycelial growth and provide theoretical basis for further expanding the application range of white-rot fungi. [ Method Four common species of white-rot fungi were cultivated by wood meal fowl dung mixture in test tube and culture dishes. The relationship between physical properties of culture material and the growth of these mycelials were studied. [Result] The results showed the water retention capacity of culture material was decreased with the increasing of its grain size and porosity, but the decrease of its specific gravity reduced the material water retention. And the dehydration rate of medium prepared with these materials at the same moisture conditions tended to increase. These physical properties of material, such as grain size, specific gravity, porosity, water retention and water drainage, influenced the growth of white-rot fungi mycelial by affecting the moisture and ventilation condition of media. The results hinted that above material physical properties had feedback effects on the growth of white-rot fungi mycelia. [ Conclution] Physical properties of culture material have significant effects on the growth of white-rot fungi mycelial.展开更多
Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy s...Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy soil（Fe-Typic Hapli-Stagnic Anthrosols） under a double cropping system.The common cropping pattern before the study was early-late rice-fallow（winter）.The field treatments included rice-rice-fallow（R-R-WF）,rice-rice-rape（R-R-RP）,rice-rice-Chinese milk vetch（RR-MV）,and rice-rice-ryegrass（R-R-RG）.The rape,Chinese milk vetch and ryegrass were all incorporated as green manures 15 d before early rice transplanting during the following year.The soil bulk density in all green manure treatments was significantly reduced compared with the winter fallow treatment.Soil porosity with green manure applications was significantly higher than that under the winter fallow.The green manure treatments had higher 0.25-5 mm water stable aggregates and aggregates stabilities in the plow layer（0-15 cm depth） compared with the fallow treatment.The mean weight diameter（MWD） and normalized mean weight diameter（NMWD） of aggregates in the green manure treatment were larger than that with the winter fallow.Soil given green manure retained both a higher water holding capacity in the plow layer soil,and a larger volume of moisture at all matric potentials（-10,-33 and-100 kPa）.We conclude that the management of double-rice fields in southern central China should be encouraged to use green manures along with chemical fertilizers to increase SOC content,improve soil physical properties and soil fertility.展开更多
The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shan...The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shanxi formations have a stable distribution. The coal reservoir of target areas such as Jincheng, Yanquan-Shouyang, Hancheng, Liulin, etc. have good CBM-bearing characteristics, high permeability and appropriate reservoir pressure, and these areas are the preferred target areas of CBM developing in China. The coal reservoirs of Wupu, Sanjiaobei, Lu'an, Xinmi, Anyang-Hebi, Jiaozuo, Xinggong and Huainan also have as good CBM-bearing characteristics, but the physical properties of coal reservoirs vary observably. So, further work should be taken to search for districts with high pressure, high permeability and good CBM-bearing characteristics. Crustal stresses have severe influence on the permeability of coal reservoirs in North China. From west to east, the crustal stress gradient increases, while the coal reservoirs permeability decreases.展开更多
The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The co...The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The corresponding physical properties of 37. 91% CAO-43.09% SiO2-5% Al2O3-5% MgO-2% Li20-7% B2O3 mould fluxes were as follows： the melting point was 909℃, the flowing temperature was 1 160℃, the viscosity and surface tension at 1300 ℃ were 0. 4 Pa · s and 0.32 N/m respectively, which could meet the demands for certain kinds of steels for mould fluxes in continuous casting.展开更多
[Objective] The aim was to study on changing rules of physical and chemical properties of Eucalyptus uraphylla spp. forest at different ages in Southwest of Yunnan Province. [Method] In the research, field survey and ...[Objective] The aim was to study on changing rules of physical and chemical properties of Eucalyptus uraphylla spp. forest at different ages in Southwest of Yunnan Province. [Method] In the research, field survey and laboratory analysis were adopted to study on physical and chemical properties of soils for the Eucalyptus uraphylla spp. at the first cutting ages in Lancang County. [Result] With the increasing of forest ages, for physical properties of soils, soil bulk density was increasing, and soil structure became poor; water contents in soils and capillary porosity were improving, but total soil porosity and non-capillary porosity were decreasing. For chemical properties, pH of soil dropped, but soil acidity improved; organic matter, total N, hydrolysable nitrogen, available phosphorus, and available potassium all declined; exchangeable Ca and Mg were improving due to fertilization and Ca and Mg lower consumption. The results showed that plays important roles in water absorption of soils and vegetation growth were improved with age increase by Eucalyptus uraphylla spp. forest, but ventilation and fertility declined accordingly. [Conclusion] The research indicated that dry branches and fallen leaves should be preserved and nutrient cycling should be protected during introduction and management of Eucalyptus uraphylla spp. to guarantee the nutrients in dry branches and leaves are back to soils, providing theoretical references for management of forest plantation and environment protection.展开更多
Calcined ginger nuts admixed by fly ash and quartz sand(CGN-(F+S))has been validated to be basically compatible to earthen sites as an anchor grout.Accelerated ageing tests including water stability test,temperature a...Calcined ginger nuts admixed by fly ash and quartz sand(CGN-(F+S))has been validated to be basically compatible to earthen sites as an anchor grout.Accelerated ageing tests including water stability test,temperature and humidity cycling test,soundness test and alkali resistance test are conducted with the objective to further research the property changes of CGN-(F+S)grout.Density,surface hardness,water penetration capacity,water permeability capacity,soluble salt,scanning electron microscopy(SEM)images and energy dispersive spectrometry(EDS)spectrum of these samples have been tested after accelerated ageing tests.The results show that densities of samples decrease,surface hardness,water penetration capacity and water permeability capacity of samples increase generally.Besides,soluble salt analysis,SEM and EDS results well corroborate the changes.Based on the results it can be concluded that property changes are most serious after temperature and humidity cycling test,followed by water stability,soundness and alkali resistance test in sequence.But in general,CGN-(F+S)still has good durability.展开更多
基金funded by the Tsinghua Shenzhen International Graduate School Research Startup Funds[item number:01030100009].
文摘MICP(Microbially induced calcite precipitation),an environmentally friendly soil improvement technique,has great potential in ocean engineering due to its ability to promote the precipitation of calcium carbonate through microbial activity to enhance the engineering properties of geomaterials.In this study,piezocone penetration test(CPTU)is used to evaluate the effectiveness of MICP treatment in calcareous sand.The change of physical properties(relative density D and total unit weight)of MICP treated calcareous sand is investigated by conducting CPTU on the geomaterials prepared in a series of mini calibration chambers(25 cm×50 cm).Results indicate that CPTU(tip stress,sleeve friction,and porewater pressure)measurements can be used to interpret the physical characteristics of calcareous sand treated with MICP under seawater conditions.Additionally,a relationship between CPTU measurements,physical parameters(relative density D,and total unit weight y)of MICP treated calcareous sand is proposed and calibrated.The findings of the research extend the implementation of in-situ testing techniques such as CPTU towards physical property evaluation of bio-treated geomaterials in ocean environment,and demonstrate the potential of scaling up MICP techniques for broader engineeringapplication.
基金Supported by National Natural Science Foundation of China"Research of soil system evolvement rule and its driving mechanism of abandoned farmland in the Middle and lower Shiyang River"(41161049)"Research of Dynamic Change and Ecological Effects of groundwater by Human intervention in downstream of the Shiyang River"(31260129)~~
文摘The vast area of farmland was abandoned at downstream of the Shiyang River because of decreased water recourse. To ensure the ecological safety of Minqin Oasis and to provide management basis for the abandoned land, soil physical properties were observed and studied. The authors analyzed land with abandonment time of 1 year, 2 years, 3 years, 4 years, 5 years, 8 years, 15 years, 24 years and 31 years. Samples were took at the 0-40 cm layer of soil to measure the bulk density, porosity and grain composition of soil in the different abandoned lands. Results showed that the tendency of clay content was decreasing, conversely, the fine sand increased at the layer of 0-10 cm of different abandoned lands.The changes of grain content reached a peak at the fourth year after the land was abandoned, then varied slightly. The variation of grain content of abandoned land was obvious with the extension of the abandonment year. The soil bulk density decreased and porosity increased with the extension of the abandonment year. The difference of porosity and soil bulk density at the range of 0-40 cm of different abandoned land decreased after the land abandoned for 3 years. The quality of soil was decreased, while the soil permeability was improved. The soil physical properties changed obviously in 3 to 4 years after abandonment, so it is the key time for land management.
基金Supported by the National Basic Research Program of China under Grant Nos 2015CB921303,2011CBA00100 and 2012CB821404the Strategic Priority Research Program(B) of Chinese Academy of Sciences under Grant Nos XDB07020100and XDB07020200the National Natural Science Foundation of China under Grant No 11174350
文摘We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are success- fully obtained. The measurement of temperature dependence of electricaJ resistivity p（T） in both normal and superconducting states indicates a quasi-two-dimensional electronic state in contrast to that of polycrystalline samples. Specific heat C（T） measurement reveals a bulk superconductivity with Tc ≈ 3.75K and a specific heat jump ratio of 1.42. All these results are in agreement with a moderately electron-phonon coupled, type-g Bardeen-Cooper-Schrieffer superconductor.
基金State Key Basic Development and Programming Project (G1998040702)the Project (9691307) from Ministry of Science and Technology and China Seismological Bureau.
文摘2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into con-sideration. The result shows that: 1) Average crustal velocity ratio is obviously higher in Tarim block than in West Kunlun Mts. and Tianshan fold zone, which reflects its crustal physical property of 'hardness' and stability. The relatively low but normai velocity ratio (Poisson's ratio) of the lower crust indicates that the 'downward thrusting' of Tarim basin is the main feature of crustal movement in this area. 2) The rock layer in the upper crust of Tianshan fold zone is relatively 'soft', which makes it prone to rupture and stress energy release. This is the primary tectonic factor for the concentration of small earthquakes in this area. 3) Jiashi is located right over the apex or the inflection point of the updoming lower crustal interface C and the crust-mantle boundary, which is the deep struc-tural background for the occurrence of strong earthquakes. The alternate variation of vp/vs near the block bounda-ries and the complicated configuration of the interfaces in the upper and middie part of the upper crust form a par-ticular structural environment for the Jiashi strong earthquake swarm. vp/vs is comparatively high and shear modulus is low at the focal region, which may be the main reason for the low stress drop of the Jiashi strong earthquake swarm.
文摘From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the physical propenies of the slag and the mass action concentrations of its have been set up at certain temperature and slag composition range, which based on the thermodynamic data of the chemtical reactions between the units and the method of linear regression. The calculated data from the model are in good agreement with the measured results. These calculated values are more accurate and systematic than those from other expirical and semi-expirical formulas used at present.
文摘In this work,multiple molecular dynamics simulations of protein G and protein L unfolding trajectories provide a direct demonstration of the diversity of unfolding pathway and give a statistically utmost unfolding pathway under the physical property space.
基金jointly supported by the National Natural Science Foundation of China(42474156)the Technical Service Project of China Oilfield Services Limited(YJB23YF001)。
文摘The Liushagang Formation in the Weixinan Depression,Beibu Gulf Basin,southern China,is one of the key stratigraphic units for offshore shale oil exploration in the country.The shale oil reservoirs in the formation are characterized by low porosity,low permeability and strong heterogeneity,which constrain the precise evaluation of reservoir properties,the accurate prediction of sweet spots,and efficient development.This study integrates core observation,mineralogical analysis,and multi-scale pore characterization to systematically clarify the variations in reservoir properties and their controlling mechanisms.The results show that the physical properties of matrix-type,lamina-type,and interlayer-type reservoirs exhibit distinct stepwise variations:Among these,interlayer-type reservoirs show the greatest development potential(quartz content 65%,average porosity 15%,permeability>10 mD,and mobile fluid saturation 60%),whereas matrix-type reservoirs are the least favorable(dominated by 40 nm nanoscale pores,and clay content 45%).Mineral composition,sedimentary-diagenetic processes,and fault systems collectively control reservoir property heterogeneity.Quartz-rich rigid frameworks resist compaction,resulting in a porosity increase by approximately 2% for every 10%rise in q uartz content.The transformation of clay minerals induces stratified porosity zoning within the layered reservoirs,while fault systems enhance heterogeneity through the development of fracture networks and acid-induced dissolution.This study provides theoretical support for the evaluation and development of shale oil sweet spots in the Weixinan Depression and holds practical significance for the commercial development of shale oil in China's offshore areas.
基金supported by National Key R&D Program of China (2022YFD1900104)。
文摘To maintain soil quality under long-term saline water irrigation,the influence of manure on soil physical properties was examined.Long-term saline irrigation has been conducted from 2015 to 2024 at the Nanpi Eco-Agricultural Experimental Station of Chinese Academy Sciences in the Low Plain of the North China Plain,comprising four irrigation treatments:irrigation once at the jointing stage for winter wheat with irrigation water containing salt at fresh water,3,4 and 5 g·L^(–1),and maize irrigation at sowing using fresh water.Manure application was conducted under all irrigation treatments,with treatments without manure application used as controls.The results showed that under long-term irrigation with saline water,the application of manure increased the soil organic matter content,exchangeable potassium,available phosphorus,and total nitrogen content in the 0–20 cm soil layer by 46.8%,117.0%,75.7%,and 45.5%,respectively,compared to treatments without manure application.The application of manure reduced soil bulk density.It also increased the proportion of water-stable aggregates and the abundance of bacteria,fungi,and actinomycetes in the tillage soil layer compared to the controls.Because of the salt contained in the manure,the application of manure had dual effects on soil salt content.During the winter wheat season,manure application increased soil salt content.The salt content was significantly reduced during the summer maize season,owing to the strong salt-leaching effects under manure application,resulting in a smaller difference in salt content between the manure and non-manure treatments.During the summer rainfall season,improvements in soil structure under manure application increased the soil desalination rate for the 1 m top soil layer.The desalination rate for 0–40 cm and 40–100 cm was averagely by 39.1%and 18.9%higher,respectively,under manure application as compared with that under the nomanure treatments.The yield of winter wheat under manure application was 0.12%lower than that of the control,owing to the higher salt content during the winter wheat season.In contrast,the yield of summer maize improved by 3.9%under manure application,owing to the increased soil nutrient content and effective salt leaching.The results of this study indicated that manure application helped maintain the soil physical structure,which is important for the long-term use of saline water.In practice,using manure with a low salt content is suggested to reduce the adverse effects of saline water irrigation on soil properties and achieve sustainable saline water use.
文摘Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field life,part of them has entered the high water cut and high recovery stage.Traditional water flooding way for improving oil recovery becomes more difficult,and new method has to be considered.Maling oilfield BS district is a typical representative,with high water cut of 90.8%,high recovery percent of 26.1%and low oil recovery rate of 0.25%.To explore the new way to improve oil recovery,the polymer and surfactant(SP for short)important pilot test has been developed.The low permeability reservoir indoor core data in high water cut stage and inspection well results indicate that the reservoir permeability,pore combination characteristics and pore type changed greatly after long-term water flooding development.These changes bring more difficulties to the continue development,especially the high injection pressure,which can cause other problems for well pattern infilling and EOR.This paper takes the high injection pressure problem of Maling BS district Jurassic reservoir for example,analyzes the physical property change law on the following aspects:the development mode in the past,core analysis,formation sensitivity,interstitial matter,well test interpretation results,in order to help to further effective development and provide important parameters for tertiary oil recovery technique for similar reservoirs and others.
基金The authors are grateful for the financial support from the National Natural Science Foundation of China(Grant Nos.52225904 and 52039007)the Natural Science Foundation of Sichuan Province(Grant No.2023NSFSC0377)supported by the New Cornerstone Science Foundation through the XPLORER PRIZE.
文摘Exploring dynamic mechanical responses and failure behaviors of hot dry rock(HDR)is significant for geothermal exploitation and stability assessment.In this study,via the split Hopkinson pressure bar(SHPB)system,a series of dynamic compression tests were conducted on granite treated by cyclic thermal shocks at different temperatures.We analyzed the effects of cyclic thermal shock on the thermal-related physical and dynamic mechanical behaviors of granite.Specifically,the P-wave velocity,dynamic strength,and elastic modulus of the tested granite decrease with increasing temperature and cycle number,while porosity and peak strain increase.The degradation law of dynamic mechanical properties could be described by a cubic polynomial.Cyclic thermal shock promotes shear cracks propagation,causing dynamic failure mode of granite to transition from splitting to tensile-shear composite failure,accompanied by surface spalling and debris splashing.Moreover,the thermal shock damage evolution and coupled failure mechanism of tested granite are discussed.The evolution of thermal shock damage with thermal shock cycle numbers shows an obvious S-shaped surface,featured by an exponential correlation with dynamic mechanical parameters.In addition,with increasing thermal shock temperature and cycles,granite mineral species barely change,but the length and width of thermal cracks increase significantly.The non-uniform expansion of minerals,thermal shock-induced cracking,and water-rock interaction are primary factors for deteriorating dynamic mechanical properties of granite under cyclic thermal shock.
基金financially supported by the National Key R&D Program of China(Nos.2021YFA1200102,2021YFA1200101,2023YFF1205803,2022YFE0128700)the National Natural Science Foundation of China(Nos.22173050,22150013,21727806,21933001)+1 种基金Beijing National Laboratory for Molecular Sciences(No.BNLMS-CXXM-202407)the Natural Science Foundation of Beijing(No.2222009)
文摘Transition metal possesses a unique d-orbital electronic structure,which imparts a diverse range of physical and chemical properties.These properties render them significant in fields such as chemistry and materials science.The distinctive optical,electrical,and magnetic properties of these complexes can be attributed to the variations in the quantity of d-orbital electrons,thereby influencing their spin and orbital characteristics.The d-orbitals facilitate the formation of stable multidirectional bonds with ligands,resulting in a variety of geometric structures and rich coordination chemistry.These interactions result in variations in energy levels,thereby producing diverse electrical properties,including low attenuation coefficients,high rectification ratios,and unique multichannel transmission.Moreover,the unpaired electrons inthe d-orbitals can give rise to diverse magnetic behaviors,leading to magnetic effects such as spin-related interfaces,switches,and magnetoresistance.This paves the way for extensive possibilities in the design and application of single-molecule devices.This review elaborates on singlemolecule physical properties of transition metal complexes,including length attenuation,rectification,multi-channel transmission,thermoelectric effect,and spin regulation,which are vital for the functionalization and regulation of molecular electronics.In addition,this review also explores the correlation between these physical properties and the electronic structure of transition metals,discussing the broad prospects of transition metal complexes in the fields of nanoelectronics,optoelectronics,and quantum technology.
文摘This review aims to identify the assets and limitations of Dabema(Piptadeniastrum africanum)as a sustainable alternative to traditional timber species for furniture and construction applications.Dabema is characterized by its high density and dimensional stability,meeting ASTM(American Society for Testing and Materials)standards for mechanical strength,which is essential for promoting its use.However,its limited availability in trade and ingrained habits of use are obstacles to its widespread commercialization.In addition,thermal and oleothermal treatments have shown great potential for improving the characteristics of this wood,although they require ongoing optimization and rigorous environmental assessment.Consequently,increased awareness of the benefits of Dabema is decisive to encourage its sustainable adoption in modern economies.This could help to diversify forest resources and encourage more sustainable building practices,taking advantage of Dabema’s unique properties while mitigating environmental sustainability concerns.
基金supported by the National Natural Science Foundation of China(Grant No.52375340,51975263,52405366).
文摘A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of shielding gases with varying He-Ar ratios,and the coupling between arc plasma and laser-induced metal plume.The accuracy of the model is validated using a high-speed camera.The effects of varying He contents in the shielding gas on both the temperature and flow velocity of hybrid plasma,as well as the distribu-tion of laser-induced metal vapor mass,were investigated separately.The maximum temperature and size of arc plasma decrease as the He volume ratio increases,the arc distribution becomes more concentrated,and its flow velocity initially decreases and then sharply increases.At high helium content,both the flow velocity of hybrid plasma and metal vapor are high,the metal vapor is con-centrated on the right side of keyhole,and its flow appears chaotic.The flow state of arc plasma is most stable when the shielding gas consists of 50%He+50%Ar.
文摘Coral sand is a unique material developed in the tropical ocean environment, which is mainly composed of coral and other marine organism debris, with the CaCO3 content up to 96 %. It has special physical and mechanical properties due to its composition, structure and sedimentary environment. In this contribution, we discuss its specific gravity, porosity ratio compressibility, crushing, shearing and intensity for coral sand samples from the Nansha islands based on laboratory mechanical tests. Our results show distinct high porosity ratio, high friction angle and low intensity as compared with the quartz sand. We believe that grain crushing is the main factor that influences the deformation and strength of coral sand. Comprehensive study on the physical and mechanical properties of coral sands is significant in providing reliable scientific parameters to construction on coral islet, and thus avoids accidents in construction.
基金Supported by Qian Jiang Manpower Program of Zhejiang Province Science and Technology Department (No.2007R10039)National Basic Research Program of China (No.2005CB724204)Under-graduate Technology Innovation Program of Zhejiang Province~~
文摘[ Objective] The research aimed to study effects of material physical properties on white-rot fungi mycelial growth and provide theoretical basis for further expanding the application range of white-rot fungi. [ Method Four common species of white-rot fungi were cultivated by wood meal fowl dung mixture in test tube and culture dishes. The relationship between physical properties of culture material and the growth of these mycelials were studied. [Result] The results showed the water retention capacity of culture material was decreased with the increasing of its grain size and porosity, but the decrease of its specific gravity reduced the material water retention. And the dehydration rate of medium prepared with these materials at the same moisture conditions tended to increase. These physical properties of material, such as grain size, specific gravity, porosity, water retention and water drainage, influenced the growth of white-rot fungi mycelial by affecting the moisture and ventilation condition of media. The results hinted that above material physical properties had feedback effects on the growth of white-rot fungi mycelia. [ Conclution] Physical properties of culture material have significant effects on the growth of white-rot fungi mycelial.
基金supported by Special Fund for Agro-scientific Research in the Public Interest(201103005)Ministry of Agriculture,China and the International Plant Nutrition Institute(IPNI,Hunan-14)
文摘Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy soil（Fe-Typic Hapli-Stagnic Anthrosols） under a double cropping system.The common cropping pattern before the study was early-late rice-fallow（winter）.The field treatments included rice-rice-fallow（R-R-WF）,rice-rice-rape（R-R-RP）,rice-rice-Chinese milk vetch（RR-MV）,and rice-rice-ryegrass（R-R-RG）.The rape,Chinese milk vetch and ryegrass were all incorporated as green manures 15 d before early rice transplanting during the following year.The soil bulk density in all green manure treatments was significantly reduced compared with the winter fallow treatment.Soil porosity with green manure applications was significantly higher than that under the winter fallow.The green manure treatments had higher 0.25-5 mm water stable aggregates and aggregates stabilities in the plow layer（0-15 cm depth） compared with the fallow treatment.The mean weight diameter（MWD） and normalized mean weight diameter（NMWD） of aggregates in the green manure treatment were larger than that with the winter fallow.Soil given green manure retained both a higher water holding capacity in the plow layer soil,and a larger volume of moisture at all matric potentials（-10,-33 and-100 kPa）.We conclude that the management of double-rice fields in southern central China should be encouraged to use green manures along with chemical fertilizers to increase SOC content,improve soil physical properties and soil fertility.
基金These research results are a part of the National Key Foundation Research Development an d Plan ning Program of China(No.2002CB2ll702)National Natural Science Foundation of China(No.40272069)
文摘The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shanxi formations have a stable distribution. The coal reservoir of target areas such as Jincheng, Yanquan-Shouyang, Hancheng, Liulin, etc. have good CBM-bearing characteristics, high permeability and appropriate reservoir pressure, and these areas are the preferred target areas of CBM developing in China. The coal reservoirs of Wupu, Sanjiaobei, Lu'an, Xinmi, Anyang-Hebi, Jiaozuo, Xinggong and Huainan also have as good CBM-bearing characteristics, but the physical properties of coal reservoirs vary observably. So, further work should be taken to search for districts with high pressure, high permeability and good CBM-bearing characteristics. Crustal stresses have severe influence on the permeability of coal reservoirs in North China. From west to east, the crustal stress gradient increases, while the coal reservoirs permeability decreases.
基金Item Sponsored by National Natural Science Foundation of China (50474037) Jiangsu Province Natural Science Foundation forUniversity of China (04BJK430022)
文摘The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The corresponding physical properties of 37. 91% CAO-43.09% SiO2-5% Al2O3-5% MgO-2% Li20-7% B2O3 mould fluxes were as follows： the melting point was 909℃, the flowing temperature was 1 160℃, the viscosity and surface tension at 1300 ℃ were 0. 4 Pa · s and 0.32 N/m respectively, which could meet the demands for certain kinds of steels for mould fluxes in continuous casting.
基金Supported by National Natural Science Foundation of China (40961031)Applied Basic Research Programs of Yunnan Province (2009CD022)Young and Middle-aged Teachers Training of Yunnan University (XT412003)~~
文摘[Objective] The aim was to study on changing rules of physical and chemical properties of Eucalyptus uraphylla spp. forest at different ages in Southwest of Yunnan Province. [Method] In the research, field survey and laboratory analysis were adopted to study on physical and chemical properties of soils for the Eucalyptus uraphylla spp. at the first cutting ages in Lancang County. [Result] With the increasing of forest ages, for physical properties of soils, soil bulk density was increasing, and soil structure became poor; water contents in soils and capillary porosity were improving, but total soil porosity and non-capillary porosity were decreasing. For chemical properties, pH of soil dropped, but soil acidity improved; organic matter, total N, hydrolysable nitrogen, available phosphorus, and available potassium all declined; exchangeable Ca and Mg were improving due to fertilization and Ca and Mg lower consumption. The results showed that plays important roles in water absorption of soils and vegetation growth were improved with age increase by Eucalyptus uraphylla spp. forest, but ventilation and fertility declined accordingly. [Conclusion] The research indicated that dry branches and fallen leaves should be preserved and nutrient cycling should be protected during introduction and management of Eucalyptus uraphylla spp. to guarantee the nutrients in dry branches and leaves are back to soils, providing theoretical references for management of forest plantation and environment protection.
基金Project(51578272)supported by the National Natural Science Foundation of China
文摘Calcined ginger nuts admixed by fly ash and quartz sand(CGN-(F+S))has been validated to be basically compatible to earthen sites as an anchor grout.Accelerated ageing tests including water stability test,temperature and humidity cycling test,soundness test and alkali resistance test are conducted with the objective to further research the property changes of CGN-(F+S)grout.Density,surface hardness,water penetration capacity,water permeability capacity,soluble salt,scanning electron microscopy(SEM)images and energy dispersive spectrometry(EDS)spectrum of these samples have been tested after accelerated ageing tests.The results show that densities of samples decrease,surface hardness,water penetration capacity and water permeability capacity of samples increase generally.Besides,soluble salt analysis,SEM and EDS results well corroborate the changes.Based on the results it can be concluded that property changes are most serious after temperature and humidity cycling test,followed by water stability,soundness and alkali resistance test in sequence.But in general,CGN-(F+S)still has good durability.
