Niobium pentoxide(Nb2O5)has attracted much attention in lithium batteries due to its advantages of high operating voltage,large theoretical capacity,environmental friendliness and cost-effectiveness.However,the intrin...Niobium pentoxide(Nb2O5)has attracted much attention in lithium batteries due to its advantages of high operating voltage,large theoretical capacity,environmental friendliness and cost-effectiveness.However,the intrinsic poor electrical conductivity,sluggish kinetics,and large volume changes hinder its electrochemical performance at high power density,making it away from the requirements for practical applications.In this research work,we regulate the electron transport of niobium-nickel oxide(NiNbO)anode material with enhanced structural stability at high power density by constructing the two-phase boundaries between niobium pentoxide(Nb2O5)and nickel niobate(NiNb2O6)through simple solid phase reaction.In addition,the presence of lattice defects in NiNbO-F further speeds up the transport of Li+and promotes the electrochemical reaction kinetics more effectively.The two-phase boundaries and defect modulated anode material displays high Li+diffusion coefficient of 1.63×10^(−10) cm^(2) s^(−1),pretty high initial discharge capacity of 222.8 mAh g^(−1) at 1 C,extraordinary high rate performance(66.7 mAh g^(−1))at an ultrahigh rate(100 C)and ultra-long cycling stability under high rate of 25 C(83.4 mAh g^(−1) after 2000 cycles)with only 0.016%attenuation per cycle.These results demonstrate an effective approach for developing electrode materials that greatly improve rate performance and durability.展开更多
A hierarchically structured MnO_(x)-NiCo_(2)O_(4) monolithic catalyst with rich phase interfaces was designed by a simple,eco-friendly and time-saving in-situ electro-deposition method.The abundance of active oxygen s...A hierarchically structured MnO_(x)-NiCo_(2)O_(4) monolithic catalyst with rich phase interfaces was designed by a simple,eco-friendly and time-saving in-situ electro-deposition method.The abundance of active oxygen species due to this rich phase interfaces contributed to the excellent benzene combustion performance of MnO_(x)-NiCo_(2)O_(4)-2:2 sample,oxidizing about 90% of benzene(T_(90)) at 198℃ under 12000 h^(-1) gaseous hourly space velocity.This work shed new light on the design of excellent monolithic catalysts,which might pave the way for the industrialization of benzene combustion.展开更多
The segregation of Mg to phase interfaces in a nickel base superalloy IN 100 has been investi- gated using EPT(Electron Microprobe Technique).AES(Auger Electron Spectroscopy) and EDS analyses on thin TEM film.The resu...The segregation of Mg to phase interfaces in a nickel base superalloy IN 100 has been investi- gated using EPT(Electron Microprobe Technique).AES(Auger Electron Spectroscopy) and EDS analyses on thin TEM film.The results show that Mg segregates to the phase inter- faces of MC/γ and γ′/γ.The segregation concentration and layer thickness of Mg on MC/γ phase interface are larger than that on γ′/γ phase interface.Mg is not only a grain boundary segregation element,but also a phase interface segregation one.展开更多
Phase change thermal interface materials(PC-TIMs)have emerged as a promising solution to address the increasing thermal management challenges in electronic devices.This is attributed to their dual mechanisms of latent...Phase change thermal interface materials(PC-TIMs)have emerged as a promising solution to address the increasing thermal management challenges in electronic devices.This is attributed to their dual mechanisms of latent heat absorption and phase change-induced interfacial wettability.This review explores the fundamental principles,material innovations,and diverse applications of PC-TIMs.The heat transfer enhancement mechanisms are first underlined with key factors such as thermal carrier mismatch at the microscale and contact geometry at the macroscale,emphasizing the importance of material selection and design for optimizing thermal performance.Section 2 focuses on corresponding experimental approaches provided,including intrinsic thermal conductivity improvements and interfacial heat transfer optimization.Section 3 discusses common methods such as physical adsorption via porous materials,chain-crosslinked network designs,and core-shell structures,and their effects on leakage prevention,heat transfer enhancement,and application flexibility.Furthermore,the extended applications of PC-TIMs in thermal energy storage are explored in Section 4,suggesting their potential in diverse technological fields.The current challenges in interfacial heat transfer research and the prospect of PC-TIMs are also discussed.The data-driven machine learning technologies will play an increasingly important role in addressing material development and performance prediction.展开更多
Converting CO_(2) into high‐value fuels and chemicals by renewable‐electricitypowered electrochemical CO_(2) reduction reaction(CRR)is a viable approach toward carbon‐emissions‐neutral processes.Unlike the thermoc...Converting CO_(2) into high‐value fuels and chemicals by renewable‐electricitypowered electrochemical CO_(2) reduction reaction(CRR)is a viable approach toward carbon‐emissions‐neutral processes.Unlike the thermocatalytic hydrogenation of CO_(2) at the solid‐gas interface,the CRR takes place at the three‐phase gas/solid/liquid interface near the electrode surface in aqueous solution,which leads to major challenges including the limited mass diffusion of CO_(2) reactant,competitive hydrogen evolution reaction,and poor product selectivity.Here we critically examine the various methods of surface and interface engineering of the electrocatalysts to optimize the microenvironment for CRR,which can address the above issues.The effective modification strategies for the gas transport,electrolyte composition,controlling intermediate states,and catalyst engineering are discussed.The key emphasis is made on the diverse atomic‐precision modifications to increase the local CO_(2) concentration,lower the energy barriers for CO_(2) activation,decrease the H2O coverage,and stabilize intermediates to effectively control the catalytic activity and selectivity.The perspectives on the challenges and outlook for the future applications of three‐phase interface engineering for CRR and other gasinvolving electrocatalytic reactions conclude the article.展开更多
It is common sense that a phase interface(or grain boundary)could be used to scatter phonons in thermoelectric(TE)materials,resulting in low thermal conductivity(k).However,a large number of impurity phases are always...It is common sense that a phase interface(or grain boundary)could be used to scatter phonons in thermoelectric(TE)materials,resulting in low thermal conductivity(k).However,a large number of impurity phases are always so harmful to the transport of carriers that poor TE performance is obtained.Here,we demonstrate that numerous superior multiphase(AgCuTe,Ag_(−2)Te,copper telluride(Cu_(2)Te and Cu_(2−x)Te),and nickel telluride(NiTe))interfaces with simultaneous strong phonon scattering and weak electron scattering could be realized in AgCuTe-based TE materials.Owing to the similar chemical bonds in these phases,the depletion region at phase interfaces,which acts as carrier scattering centers,could be ignored.Therefore,the power factor(PF)is obviously enhanced from~609 to~832μW·m^(−1)·K^(−2),and k is simultaneously decreased from~0.52 to~0.43 W·m^(−1)·K^(−1) at 636 K.Finally,a peak figure of merit(zT)of~1.23 at 636 K and an average zT(zTavg)of~1.12 in the temperature range of 523–623 K are achieved,which are one of the best values among the AgCuTe-based TE materials.This study could provide new guidance to enhance the performance by designing superior multiphase interfaces in the TE materials.展开更多
Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in ...Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in this paper under certain conditions. It demonstrates that the influence of the α/β interface phase on the tensile properties is closely associated with dislocations and twin substructure through comparison experiments. The results show that the α/β interface phase hinders dislocation motion and decreases effective slip length. In addition, the twin substructure has been activated in the α/β interface phase during tensile process and has acted somehow like grain boundaries. Therefore, the strength and the work-hardening rate of the laser cladding deposited Ti-6Al-4V titanium alloy have been significantly improved due to the dynamic Hall-Petch effect. Besides, the α/β interface phase leads to more uniform dislocations distribution, which implies that relative lower local concentrated stress will be produced along the α/β interface phase or colony boundary after the same amount of plastic deformation. Moreover,the twinning-induced plasticity effects in the α/β interface phase further increase the plastic deformation capacity. These results in higher elongation for the laser cladding deposited Ti-6Al-4V titanium alloy.It can be concluded that the current work suggests an effective method to simultaneously improve the strength and plasticity of laser cladding deposited Ti-6Al-4V titanium alloy based on the α/β interface phase.展开更多
The influences of additives on the phase transformation, occurrence state, and the interface of the Ti component in Ti-bearing blast furnace slag were investigated. After oxidation, most of the Ti component in the sla...The influences of additives on the phase transformation, occurrence state, and the interface of the Ti component in Ti-bearing blast furnace slag were investigated. After oxidation, most of the Ti component in the slag was enriched into the perovskite phase, which served as the Ti-rich phase during the crystallization process. The phase transformation, occurrence state, and the interface of the Ti component were observed to be affected by the addition of different types of agents. During the oxidation process, titanaugite and Ti-rich diopside phases gradually transformed into non-Ti phases（anorthite： CaMgSi2O6 and CaAl2Si2O8） in the form of dendrites or columns, which were observed to be distributed at the surface of the perovskite phase. Several more cracks appeared along the grain boundaries of the perovskite phase after the addition of P2O5, facilitating the liberation of the perovskite phase. Composite additives combining both an acid and a base, such as CaO ＋ CaF2 or P2O5 ＋ CaF2, were used. We observed that the disadvantages of using single additives were successfully overcome.展开更多
This work used the in-situ synthesis of molten-state nitride ceramic phase-reinforced Ni-based alloy coat-ings,aiming to improve the phase-interface bonding through the interdependent co-solidification be-tween molten...This work used the in-situ synthesis of molten-state nitride ceramic phase-reinforced Ni-based alloy coat-ings,aiming to improve the phase-interface bonding through the interdependent co-solidification be-tween molten droplets.The XRD was used to analyze the physical phases of the composite coatings.The microstructure and phase-interface structure were characterized in detail by combining SEM,TEM,HRTEM,FFT,and SAED techniques.Microhardness tester and microforce microhardness tester were em-ployed to measure the surface hardness and elastic modulus of the composite coatings.The fracture be-havior of the composite coatings was characterized by observing the fracture morphology of the coatings using SEM combined with the EDS technique.It was found that the formation mechanisms of inter-facial misfit dislocation assistance,lattice distortion,aggregation of stacking faults,and specific growth orientation between theγ-Ni matrix phase and each ceramic phase in NiCrBSi-TiCrN composite coat-ings improved the lattice matching between the two-phase interface,which resulted in the formation of atomically corresponding coherent lattice relations and stepped interfacial semi-coherent lattice relations,and enhanced the degree of phase-interface bonding.On this basis,the composite coatings with high Cr content further inhibited the expansion of interphase penetration cracks due to the existence of Cr-rich zones at the phase interface,thus exhibiting high fracture toughness.This work provides new opinions on the improvement of phase-interface bonding and composition design of Ni-based composite coatings.展开更多
An important step for achieving the knowledge-based design freedom on nano-and interfacial materials is attained by elucidating the related surface and interface thermodynamics from the first principles so as to allow...An important step for achieving the knowledge-based design freedom on nano-and interfacial materials is attained by elucidating the related surface and interface thermodynamics from the first principles so as to allow engineering the microstructures for desired properties through smartly designing fabrication processing parameters.This is demonstrated for SnO2 nano-particle surfaces and also a technologically important Ag-SnO2 interface fabricated by in-situ internal oxidation.Based on defect thermodynamics,we first modeled and calculated the equilibrium surface and interface structures,and as well corresponding properties,as a function of the ambient temperature and oxygen partial pressure.A series of first principles energetics calculations were then performed to construct the equilibrium surface and interface phase diagrams,to describe the environment dependence of the microstructures and properties of the surfaces and interfaces during fabrication and service conditions.The use and potential application of these phase diagrams as a process design tool were suggested and discussed.展开更多
The dislocation ledges at the α2/7 intedece in a hot-dejormed Ti-45Al-10N alloywere analyzed by high-resolution tmnsmission electron microscopy. A new type ofdislocation ledge containing 1/3[111] Frank partial was fo...The dislocation ledges at the α2/7 intedece in a hot-dejormed Ti-45Al-10N alloywere analyzed by high-resolution tmnsmission electron microscopy. A new type ofdislocation ledge containing 1/3[111] Frank partial was found. The height of the ledgestDas always three [111]γplanes. The Burpers vectore of these diBlocation ledges weredetermined to be 1/2[110] and 1/2<101] corresponding to the 90 dey. and 30 deg.Shockley partials at noral ledges, i.e. 90 dep. ShockIey Partial dislocation +1/3[111]Frank partial dislocation; and 30 deg. Shockley partial dislocation + 1/3[111] Frankparfial dislocations. The jormation mechanism of this new tare of dislocation ledgewas discussed.展开更多
A detailed fracture mechanics analysis of bridge-toughening in a fiber reinforced composite is presented in this paper. The integral equation governing bridge-toughening as well as crack opening displacement (COD) for...A detailed fracture mechanics analysis of bridge-toughening in a fiber reinforced composite is presented in this paper. The integral equation governing bridge-toughening as well as crack opening displacement (COD) for the composite with interfacial layer is derived from the Castigliano's theorem and interface shear-lag model. A numerical result of the COD equation is obtained using the iteration solution of the second Fredholm integral equation. In order to investigate the effect of various parameters on the toughening, an approximate analytical solution of the equation is present and its error analysis is performed, which demonstrates the approximate solution to be appropriate. A parametric study of the influence of the crack length, interfacial shear modules, thickness of the interphase, fiber radius, fiber volume fraction and properties of materials on composite toughening is therefore carried out. The results are useful for experimental demonstration and toughening design including the fabrication process of the composite.展开更多
This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to externa...This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to external magnetic fields.A micromechanical model was created by simplifying the basic properties and composition of the interface,utilizing principles such as Eshelby’s equivalent inclusion theory and Hooke’s law,as well as applying uniform stress boundary conditions.Through the development of equations,the study predicted changes in effective mechanical properties,highlighting the significant influence of parameters like the interface phase,inclusions,and magnetic field on the effective elastic modulus and magnetostriction of the composite material.By shedding light on these relationships,the research offers valuable insights for the manufacture and application of ferromagnetic particle-reinforced superconducting matrix composites with interface phases,providing a foundation for future research in this area.展开更多
It is extremely difficult to introduce high-density nano twins during the solidification process of TiAl alloy.In this study,high-density nanotwins are inducted in the as-cast Ti48Al2Cr alloyed by adding Re element.Ph...It is extremely difficult to introduce high-density nano twins during the solidification process of TiAl alloy.In this study,high-density nanotwins are inducted in the as-cast Ti48Al2Cr alloyed by adding Re element.Phase transformation,morphology characteristics of nano twins,compressive and tensile proper-ties,and the related mechanisms have been studied.Results show that B2 phase enriched with Re tends to precipitate along theα_(2)/γinterface within lamellar colony.The stacking fault energy(SFE)ofγphase decreases from 43 mJ/m^(2) to 16 mJ/m^(2) as Re content increases from 0 at.%to 0.6 at.%,decreasing the crit-ical shear stress for twin formation.Compared to the mismatch value ofα_(2)/γinterface(0.004),which of B2/α_(2) and B2/γinterfaces increase to 0.247 and 0.149,respectively.Driven by high interfacial stress,high-density dislocations are generated at the B2/α_(2) interface,providing the dislocation slip channel for the formation of stacking faults(SFs)and nanotwins at the B2/γinterface.Therefore,the mechanism of inducting high-density nanotwins is to reduce the stacking fault energy ofγphase by Re and form highly mismatched B2/α_(2) interface.Compressive strength and the strain increase from 1723 MPa to 2398 MPa and 29%to 39%as Re content increases from 0 at.%to 0.6 at.%,respectively.Tensile strength increases from 356 MPa to 452 MPa without sacrificing plasticity.The improvement in strength and plasticity are attributed to the nano-twinning strengthening and interfacial thermal mismatch strengthening.Forming nanotwins during solidification process serve as the nucleation sites for newly formed twins during de-formation process,increasing the deformation tolerance of TiAl alloy.展开更多
The deformation and micro-voids formation mechanisms in ferrite / bainite（ F / B） multi-phase steel with the volume fraction of bainite less than 50% were studied by numerical simulation and experimental observation...The deformation and micro-voids formation mechanisms in ferrite / bainite（ F / B） multi-phase steel with the volume fraction of bainite less than 50% were studied by numerical simulation and experimental observation. The results show that the micro-strain concentrates at the soft / hard phase（ F / B） interface in the multi-phase steel,which should be correlated with the mechanism of incoordinate deformation. During the necking of the steel,the micro-voids initially form around the F / B interface,which also form in ferrite and bainite with the severe strain. The micro-voids in bainite are more dense and finer than those in ferrite. The failure mechanism of bainite is the coalescence of micro-voids,and the failure mechanism of ferrite is the growth and tearing of micro-voids. Due to the different failure mechanisms of ferrite and bainite,a suitable part of soft phase would be beneficial to the capability of anti-failure of F / B multi-phase steel during the ductile fracture.展开更多
Aberration-corrected scanning transmission electron microscopy was employed to investigate the microstructures and secondary phases in LaBaCo2O5.5＋δ（LBCO） thin films grown on SrTiO3 （STO） substrates. The as-grow...Aberration-corrected scanning transmission electron microscopy was employed to investigate the microstructures and secondary phases in LaBaCo2O5.5＋δ（LBCO） thin films grown on SrTiO3 （STO） substrates. The as-grown films showed an epitaxial growth on the substrates with atomically sharp interfaces and orientation relationships of [100]LBCO//[100]STO and （001）LBCO//（001）STO. Secondary phases were observed in the films, which strongly depended on the sample fabrication conditions. In the film prepared at a temperature of 900 ℃, nano-scale CoO pillars nucleated on the substrate, and grew along the [001] direction of the film. In the film grown at a temperature of 1000 ℃, isolated nano-scale C0304 particles appeared, which promoted the growth of {111 } twinning structures in the film. The orientation relationships and the interfaces between the secondary phases and the films were illustrated, and the growth mechanism of the film was discussed.展开更多
Fatigue crack growth behaviors were investigated by three-point bending tests for TA19 alloy fabricated by laser metal deposition and four kinds of heat-treated samples.The crack growth resistance of the TA19 samples ...Fatigue crack growth behaviors were investigated by three-point bending tests for TA19 alloy fabricated by laser metal deposition and four kinds of heat-treated samples.The crack growth resistance of the TA19 samples in the near-threshold regime and Paris regime was evaluated through the experimental characterization and theoretical analysis of the interaction between fatigue crack andα/βphase inter-face,columnar prior-βgrain boundary and colony boundary.The results show that in the near-threshold regime,the fatigue crack propagation threshold and resistance increase with the increase of widths of lamellarαp phases and colonies,and the decrease of the number ofαlaths with an angle(ϕ)relative to the applied stress direction ranging from 75°to 90°.In the Paris regime,the fatigue cracking path can be deflected at colony boundaries or columnar prior-βgrain boundaries.The larger the deflection angle,the more tortuous the cracking path and the lower the fatigue crack growth rate.The angle(γ)of the columnar prior-βgrain growth direction relative to the build direction affects not onlyϕof differentαvariants,but also the fatigue cracking path deflection angle(θij)at columnar prior-βgrain boundaries.An optimal combination ofγ=0°-15°-0°-15°for several adjacent columnar prior-βgrains is derived from the theoretical analysis,and that can effectively avoidϕbeing in the range from 75°to 90°and makeθij as large as possible.Such findings provide a guide for the selection of scanning strategies and process parameters to additively manufacture Ti alloys with high fatigue damage tolerance.展开更多
This study of the thermal decomposition kinetics of various average diameter nano-particles of cal-cium carbonate by means of TG-DTA(thermogravimetry and differential thermal analysis) showed that the thermal decompos...This study of the thermal decomposition kinetics of various average diameter nano-particles of cal-cium carbonate by means of TG-DTA(thermogravimetry and differential thermal analysis) showed that the thermal decomposition kinetic mechanisms of the same crystal type of calcium carbonate samples do not vary with decreasing of their average diameters ; their pseudo-active energy Ea; and that the top-temperature of decom-position Tp decreases gently in the scope of micron-sized diameter, but decreases sharply when the average di-ameter decreases from micron region to nanometer region. The extraordinary properties of nano-particles were explored by comparing the varying regularity of the mechanisms and kinetic parameters of the solid-phase reac-tions as well as their structural characterization with the variation of average diameters of particles. These show that the aggregation, surface effect as well as internal aberrance and stress of the nano-particles are the main reason causing both Ea and Tp to decline sharply with the decrease of the average diameter of nano-particles.展开更多
Considering the air-water interface and ocean water’s optical attenuation,the performance of quantum key distribution(QKD)based on air-water channel is studied.The effects of photons’various incident angles to air-w...Considering the air-water interface and ocean water’s optical attenuation,the performance of quantum key distribution(QKD)based on air-water channel is studied.The effects of photons’various incident angles to air-water interface on quantum bit error rate(QBER)and the maximum secure transmission distance are analyzed.Taking the optical attenuation of ocean water into account,the performance bounds of QKD in different types of ocean water are discussed.The simulation results show that the maximum secure transmission distance of QKD gradually reduces as the incident angle from air to ocean water increases.In the clearest ocean water with the lowest attenuation,the maximum secure transmission distance of photons far exceeds the the working depth of underwater vehicles.In intermediate and murky ocean waters with higher attenuation,the secure transmission distance shortens,but the underwater vehicle can deploy other accessorial methods for QKD with perfect security.So the implementation of OKD between the satellite and the underwater vehicle is feasible.展开更多
Monte Carlo simulations were used to investigate the compatibilizing behaviors of multi-block copolymers with different architectures in A/B/（block copolymer） ternary blends. The volume fraction of homopolymer A, em...Monte Carlo simulations were used to investigate the compatibilizing behaviors of multi-block copolymers with different architectures in A/B/（block copolymer） ternary blends. The volume fraction of homopolymer A, employed as the dispersed phase, was 19%. The simulations illustrate how a di- or multi-block copolymer aggregates at the interfaces and influences the phase behaviour of such incompatible polymer blends. The di-block copolymer chains tend to ＂stand＂ on the interface whereas the multi-block chains lie on the interface. In comparison with the di-block copolymer, the block copolymers with 4, or 10 blocks can occupy more areas on the interface, and thus the multi-block copolymers have higher efficiency for the retardation of the phase separation.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52002119 and 52102346)the National Key R&D Program of China(No.2021YFB3400800)the Startup Funds from the Henan University of Science and Technology(Nos.13480095,13480096,13554031 and 13554032).
文摘Niobium pentoxide(Nb2O5)has attracted much attention in lithium batteries due to its advantages of high operating voltage,large theoretical capacity,environmental friendliness and cost-effectiveness.However,the intrinsic poor electrical conductivity,sluggish kinetics,and large volume changes hinder its electrochemical performance at high power density,making it away from the requirements for practical applications.In this research work,we regulate the electron transport of niobium-nickel oxide(NiNbO)anode material with enhanced structural stability at high power density by constructing the two-phase boundaries between niobium pentoxide(Nb2O5)and nickel niobate(NiNb2O6)through simple solid phase reaction.In addition,the presence of lattice defects in NiNbO-F further speeds up the transport of Li+and promotes the electrochemical reaction kinetics more effectively.The two-phase boundaries and defect modulated anode material displays high Li+diffusion coefficient of 1.63×10^(−10) cm^(2) s^(−1),pretty high initial discharge capacity of 222.8 mAh g^(−1) at 1 C,extraordinary high rate performance(66.7 mAh g^(−1))at an ultrahigh rate(100 C)and ultra-long cycling stability under high rate of 25 C(83.4 mAh g^(−1) after 2000 cycles)with only 0.016%attenuation per cycle.These results demonstrate an effective approach for developing electrode materials that greatly improve rate performance and durability.
基金financially supported by National Key R&D Program of China(Nos.2017YFC0211503,2016YFC0207100)the National Natural Science Foundation of China(Nos.21401200,51672273)the Open Research Fund of State Key Laboratory of Multi-phase Complex Systems(No.MPCS-2017-D-06)。
文摘A hierarchically structured MnO_(x)-NiCo_(2)O_(4) monolithic catalyst with rich phase interfaces was designed by a simple,eco-friendly and time-saving in-situ electro-deposition method.The abundance of active oxygen species due to this rich phase interfaces contributed to the excellent benzene combustion performance of MnO_(x)-NiCo_(2)O_(4)-2:2 sample,oxidizing about 90% of benzene(T_(90)) at 198℃ under 12000 h^(-1) gaseous hourly space velocity.This work shed new light on the design of excellent monolithic catalysts,which might pave the way for the industrialization of benzene combustion.
文摘The segregation of Mg to phase interfaces in a nickel base superalloy IN 100 has been investi- gated using EPT(Electron Microprobe Technique).AES(Auger Electron Spectroscopy) and EDS analyses on thin TEM film.The results show that Mg segregates to the phase inter- faces of MC/γ and γ′/γ.The segregation concentration and layer thickness of Mg on MC/γ phase interface are larger than that on γ′/γ phase interface.Mg is not only a grain boundary segregation element,but also a phase interface segregation one.
基金funding from the National Natural Science Foundation of China(Grant Nos.52306214,52425601,and 52276074)the Shanghai Chenguang Plan Program(Grant No.22CGA78)the National Key Research and the Development Program of China(Grant No.2023YFB4404104)。
文摘Phase change thermal interface materials(PC-TIMs)have emerged as a promising solution to address the increasing thermal management challenges in electronic devices.This is attributed to their dual mechanisms of latent heat absorption and phase change-induced interfacial wettability.This review explores the fundamental principles,material innovations,and diverse applications of PC-TIMs.The heat transfer enhancement mechanisms are first underlined with key factors such as thermal carrier mismatch at the microscale and contact geometry at the macroscale,emphasizing the importance of material selection and design for optimizing thermal performance.Section 2 focuses on corresponding experimental approaches provided,including intrinsic thermal conductivity improvements and interfacial heat transfer optimization.Section 3 discusses common methods such as physical adsorption via porous materials,chain-crosslinked network designs,and core-shell structures,and their effects on leakage prevention,heat transfer enhancement,and application flexibility.Furthermore,the extended applications of PC-TIMs in thermal energy storage are explored in Section 4,suggesting their potential in diverse technological fields.The current challenges in interfacial heat transfer research and the prospect of PC-TIMs are also discussed.The data-driven machine learning technologies will play an increasingly important role in addressing material development and performance prediction.
基金Australian Research Council,Grant/Award Numbers:FL170100154,FT200100062,DP220102596,DP210100472,DP190103472。
文摘Converting CO_(2) into high‐value fuels and chemicals by renewable‐electricitypowered electrochemical CO_(2) reduction reaction(CRR)is a viable approach toward carbon‐emissions‐neutral processes.Unlike the thermocatalytic hydrogenation of CO_(2) at the solid‐gas interface,the CRR takes place at the three‐phase gas/solid/liquid interface near the electrode surface in aqueous solution,which leads to major challenges including the limited mass diffusion of CO_(2) reactant,competitive hydrogen evolution reaction,and poor product selectivity.Here we critically examine the various methods of surface and interface engineering of the electrocatalysts to optimize the microenvironment for CRR,which can address the above issues.The effective modification strategies for the gas transport,electrolyte composition,controlling intermediate states,and catalyst engineering are discussed.The key emphasis is made on the diverse atomic‐precision modifications to increase the local CO_(2) concentration,lower the energy barriers for CO_(2) activation,decrease the H2O coverage,and stabilize intermediates to effectively control the catalytic activity and selectivity.The perspectives on the challenges and outlook for the future applications of three‐phase interface engineering for CRR and other gasinvolving electrocatalytic reactions conclude the article.
基金This work is supported by the National Natural Science Foundation of China(Grant Nos.52262032,52273285,51961011,52061009,and U21A2054)the National Key R&D Program of China(Grant No.2022YFE0119100)。
文摘It is common sense that a phase interface(or grain boundary)could be used to scatter phonons in thermoelectric(TE)materials,resulting in low thermal conductivity(k).However,a large number of impurity phases are always so harmful to the transport of carriers that poor TE performance is obtained.Here,we demonstrate that numerous superior multiphase(AgCuTe,Ag_(−2)Te,copper telluride(Cu_(2)Te and Cu_(2−x)Te),and nickel telluride(NiTe))interfaces with simultaneous strong phonon scattering and weak electron scattering could be realized in AgCuTe-based TE materials.Owing to the similar chemical bonds in these phases,the depletion region at phase interfaces,which acts as carrier scattering centers,could be ignored.Therefore,the power factor(PF)is obviously enhanced from~609 to~832μW·m^(−1)·K^(−2),and k is simultaneously decreased from~0.52 to~0.43 W·m^(−1)·K^(−1) at 636 K.Finally,a peak figure of merit(zT)of~1.23 at 636 K and an average zT(zTavg)of~1.12 in the temperature range of 523–623 K are achieved,which are one of the best values among the AgCuTe-based TE materials.This study could provide new guidance to enhance the performance by designing superior multiphase interfaces in the TE materials.
基金supported by the National Key Research And Development Plan, China (No. 2016YFB1100100)the Research Fund of the State Key Laboratory of Solidification Processing (NWPU), China (No. KP201611)the National Natural Science Foundation of China (No. 51475380)
文摘Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in this paper under certain conditions. It demonstrates that the influence of the α/β interface phase on the tensile properties is closely associated with dislocations and twin substructure through comparison experiments. The results show that the α/β interface phase hinders dislocation motion and decreases effective slip length. In addition, the twin substructure has been activated in the α/β interface phase during tensile process and has acted somehow like grain boundaries. Therefore, the strength and the work-hardening rate of the laser cladding deposited Ti-6Al-4V titanium alloy have been significantly improved due to the dynamic Hall-Petch effect. Besides, the α/β interface phase leads to more uniform dislocations distribution, which implies that relative lower local concentrated stress will be produced along the α/β interface phase or colony boundary after the same amount of plastic deformation. Moreover,the twinning-induced plasticity effects in the α/β interface phase further increase the plastic deformation capacity. These results in higher elongation for the laser cladding deposited Ti-6Al-4V titanium alloy.It can be concluded that the current work suggests an effective method to simultaneously improve the strength and plasticity of laser cladding deposited Ti-6Al-4V titanium alloy based on the α/β interface phase.
基金supported by the Open Research Fund of the Key Laboratory for Ferrous Metallurgy and Resources Utilization of the Ministry of EducationWuhan University of Science and Technology (FMRU2007K10)
文摘The influences of additives on the phase transformation, occurrence state, and the interface of the Ti component in Ti-bearing blast furnace slag were investigated. After oxidation, most of the Ti component in the slag was enriched into the perovskite phase, which served as the Ti-rich phase during the crystallization process. The phase transformation, occurrence state, and the interface of the Ti component were observed to be affected by the addition of different types of agents. During the oxidation process, titanaugite and Ti-rich diopside phases gradually transformed into non-Ti phases（anorthite： CaMgSi2O6 and CaAl2Si2O8） in the form of dendrites or columns, which were observed to be distributed at the surface of the perovskite phase. Several more cracks appeared along the grain boundaries of the perovskite phase after the addition of P2O5, facilitating the liberation of the perovskite phase. Composite additives combining both an acid and a base, such as CaO ＋ CaF2 or P2O5 ＋ CaF2, were used. We observed that the disadvantages of using single additives were successfully overcome.
基金supported by the National Natural Science Foundation of China(No.52271055)the Natural Science Foundation of Hebei Province(No.E2021202130).
文摘This work used the in-situ synthesis of molten-state nitride ceramic phase-reinforced Ni-based alloy coat-ings,aiming to improve the phase-interface bonding through the interdependent co-solidification be-tween molten droplets.The XRD was used to analyze the physical phases of the composite coatings.The microstructure and phase-interface structure were characterized in detail by combining SEM,TEM,HRTEM,FFT,and SAED techniques.Microhardness tester and microforce microhardness tester were em-ployed to measure the surface hardness and elastic modulus of the composite coatings.The fracture be-havior of the composite coatings was characterized by observing the fracture morphology of the coatings using SEM combined with the EDS technique.It was found that the formation mechanisms of inter-facial misfit dislocation assistance,lattice distortion,aggregation of stacking faults,and specific growth orientation between theγ-Ni matrix phase and each ceramic phase in NiCrBSi-TiCrN composite coat-ings improved the lattice matching between the two-phase interface,which resulted in the formation of atomically corresponding coherent lattice relations and stepped interfacial semi-coherent lattice relations,and enhanced the degree of phase-interface bonding.On this basis,the composite coatings with high Cr content further inhibited the expansion of interphase penetration cracks due to the existence of Cr-rich zones at the phase interface,thus exhibiting high fracture toughness.This work provides new opinions on the improvement of phase-interface bonding and composition design of Ni-based composite coatings.
基金Project(51171211) supported by the National Natural Science Foundation of ChinaProject(NCET-10-0837) supported by the Chinese Ministry of Education's Supportive Program for New Century Excellent Talents in UniversitiesProject(2006BAE03B03) supported by the Chinese National Science and Technology Supportive Program
文摘An important step for achieving the knowledge-based design freedom on nano-and interfacial materials is attained by elucidating the related surface and interface thermodynamics from the first principles so as to allow engineering the microstructures for desired properties through smartly designing fabrication processing parameters.This is demonstrated for SnO2 nano-particle surfaces and also a technologically important Ag-SnO2 interface fabricated by in-situ internal oxidation.Based on defect thermodynamics,we first modeled and calculated the equilibrium surface and interface structures,and as well corresponding properties,as a function of the ambient temperature and oxygen partial pressure.A series of first principles energetics calculations were then performed to construct the equilibrium surface and interface phase diagrams,to describe the environment dependence of the microstructures and properties of the surfaces and interfaces during fabrication and service conditions.The use and potential application of these phase diagrams as a process design tool were suggested and discussed.
文摘The dislocation ledges at the α2/7 intedece in a hot-dejormed Ti-45Al-10N alloywere analyzed by high-resolution tmnsmission electron microscopy. A new type ofdislocation ledge containing 1/3[111] Frank partial was found. The height of the ledgestDas always three [111]γplanes. The Burpers vectore of these diBlocation ledges weredetermined to be 1/2[110] and 1/2<101] corresponding to the 90 dey. and 30 deg.Shockley partials at noral ledges, i.e. 90 dep. ShockIey Partial dislocation +1/3[111]Frank partial dislocation; and 30 deg. Shockley partial dislocation + 1/3[111] Frankparfial dislocations. The jormation mechanism of this new tare of dislocation ledgewas discussed.
基金National Natural Science Foundatjon and China Postdoctoral Scjence Fbundation
文摘A detailed fracture mechanics analysis of bridge-toughening in a fiber reinforced composite is presented in this paper. The integral equation governing bridge-toughening as well as crack opening displacement (COD) for the composite with interfacial layer is derived from the Castigliano's theorem and interface shear-lag model. A numerical result of the COD equation is obtained using the iteration solution of the second Fredholm integral equation. In order to investigate the effect of various parameters on the toughening, an approximate analytical solution of the equation is present and its error analysis is performed, which demonstrates the approximate solution to be appropriate. A parametric study of the influence of the crack length, interfacial shear modules, thickness of the interphase, fiber radius, fiber volume fraction and properties of materials on composite toughening is therefore carried out. The results are useful for experimental demonstration and toughening design including the fabrication process of the composite.
基金supported by the National Natural Science Foundation of China(No.12262020).
文摘This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to external magnetic fields.A micromechanical model was created by simplifying the basic properties and composition of the interface,utilizing principles such as Eshelby’s equivalent inclusion theory and Hooke’s law,as well as applying uniform stress boundary conditions.Through the development of equations,the study predicted changes in effective mechanical properties,highlighting the significant influence of parameters like the interface phase,inclusions,and magnetic field on the effective elastic modulus and magnetostriction of the composite material.By shedding light on these relationships,the research offers valuable insights for the manufacture and application of ferromagnetic particle-reinforced superconducting matrix composites with interface phases,providing a foundation for future research in this area.
基金supported by the National Natural Science Foundation of China(No.U21A2042)the National Nature Fund Youth Fund Project of China(No.52101038)Young Elite Scientists Sponsorship Program by CAST(No.2021QNRC001).
文摘It is extremely difficult to introduce high-density nano twins during the solidification process of TiAl alloy.In this study,high-density nanotwins are inducted in the as-cast Ti48Al2Cr alloyed by adding Re element.Phase transformation,morphology characteristics of nano twins,compressive and tensile proper-ties,and the related mechanisms have been studied.Results show that B2 phase enriched with Re tends to precipitate along theα_(2)/γinterface within lamellar colony.The stacking fault energy(SFE)ofγphase decreases from 43 mJ/m^(2) to 16 mJ/m^(2) as Re content increases from 0 at.%to 0.6 at.%,decreasing the crit-ical shear stress for twin formation.Compared to the mismatch value ofα_(2)/γinterface(0.004),which of B2/α_(2) and B2/γinterfaces increase to 0.247 and 0.149,respectively.Driven by high interfacial stress,high-density dislocations are generated at the B2/α_(2) interface,providing the dislocation slip channel for the formation of stacking faults(SFs)and nanotwins at the B2/γinterface.Therefore,the mechanism of inducting high-density nanotwins is to reduce the stacking fault energy ofγphase by Re and form highly mismatched B2/α_(2) interface.Compressive strength and the strain increase from 1723 MPa to 2398 MPa and 29%to 39%as Re content increases from 0 at.%to 0.6 at.%,respectively.Tensile strength increases from 356 MPa to 452 MPa without sacrificing plasticity.The improvement in strength and plasticity are attributed to the nano-twinning strengthening and interfacial thermal mismatch strengthening.Forming nanotwins during solidification process serve as the nucleation sites for newly formed twins during de-formation process,increasing the deformation tolerance of TiAl alloy.
基金Item Sponsored by National Basic Research Program of China(2010CB630801)
文摘The deformation and micro-voids formation mechanisms in ferrite / bainite（ F / B） multi-phase steel with the volume fraction of bainite less than 50% were studied by numerical simulation and experimental observation. The results show that the micro-strain concentrates at the soft / hard phase（ F / B） interface in the multi-phase steel,which should be correlated with the mechanism of incoordinate deformation. During the necking of the steel,the micro-voids initially form around the F / B interface,which also form in ferrite and bainite with the severe strain. The micro-voids in bainite are more dense and finer than those in ferrite. The failure mechanism of bainite is the coalescence of micro-voids,and the failure mechanism of ferrite is the growth and tearing of micro-voids. Due to the different failure mechanisms of ferrite and bainite,a suitable part of soft phase would be beneficial to the capability of anti-failure of F / B multi-phase steel during the ductile fracture.
基金financially supported by the National Natural Science Foundation of China (Nos. 51501143, 51202185 and 51390472)the National Basic Research Program of China (No. 2015CB654903)Fundamental Research Funds for the Central Universities, China Postdoctoral Science Foundation (No. 2015M572554)
文摘Aberration-corrected scanning transmission electron microscopy was employed to investigate the microstructures and secondary phases in LaBaCo2O5.5＋δ（LBCO） thin films grown on SrTiO3 （STO） substrates. The as-grown films showed an epitaxial growth on the substrates with atomically sharp interfaces and orientation relationships of [100]LBCO//[100]STO and （001）LBCO//（001）STO. Secondary phases were observed in the films, which strongly depended on the sample fabrication conditions. In the film prepared at a temperature of 900 ℃, nano-scale CoO pillars nucleated on the substrate, and grew along the [001] direction of the film. In the film grown at a temperature of 1000 ℃, isolated nano-scale C0304 particles appeared, which promoted the growth of {111 } twinning structures in the film. The orientation relationships and the interfaces between the secondary phases and the films were illustrated, and the growth mechanism of the film was discussed.
基金supported by the National Natural Science Foundation of China(Nos.51771207 and 52171128)the National Science and Technology Major Project(No.J2019-VI-0012-0126)the Fundamental Research Project of Shenyang National Laboratory for Materials Science(No.L2019R18).
文摘Fatigue crack growth behaviors were investigated by three-point bending tests for TA19 alloy fabricated by laser metal deposition and four kinds of heat-treated samples.The crack growth resistance of the TA19 samples in the near-threshold regime and Paris regime was evaluated through the experimental characterization and theoretical analysis of the interaction between fatigue crack andα/βphase inter-face,columnar prior-βgrain boundary and colony boundary.The results show that in the near-threshold regime,the fatigue crack propagation threshold and resistance increase with the increase of widths of lamellarαp phases and colonies,and the decrease of the number ofαlaths with an angle(ϕ)relative to the applied stress direction ranging from 75°to 90°.In the Paris regime,the fatigue cracking path can be deflected at colony boundaries or columnar prior-βgrain boundaries.The larger the deflection angle,the more tortuous the cracking path and the lower the fatigue crack growth rate.The angle(γ)of the columnar prior-βgrain growth direction relative to the build direction affects not onlyϕof differentαvariants,but also the fatigue cracking path deflection angle(θij)at columnar prior-βgrain boundaries.An optimal combination ofγ=0°-15°-0°-15°for several adjacent columnar prior-βgrains is derived from the theoretical analysis,and that can effectively avoidϕbeing in the range from 75°to 90°and makeθij as large as possible.Such findings provide a guide for the selection of scanning strategies and process parameters to additively manufacture Ti alloys with high fatigue damage tolerance.
文摘This study of the thermal decomposition kinetics of various average diameter nano-particles of cal-cium carbonate by means of TG-DTA(thermogravimetry and differential thermal analysis) showed that the thermal decomposition kinetic mechanisms of the same crystal type of calcium carbonate samples do not vary with decreasing of their average diameters ; their pseudo-active energy Ea; and that the top-temperature of decom-position Tp decreases gently in the scope of micron-sized diameter, but decreases sharply when the average di-ameter decreases from micron region to nanometer region. The extraordinary properties of nano-particles were explored by comparing the varying regularity of the mechanisms and kinetic parameters of the solid-phase reac-tions as well as their structural characterization with the variation of average diameters of particles. These show that the aggregation, surface effect as well as internal aberrance and stress of the nano-particles are the main reason causing both Ea and Tp to decline sharply with the decrease of the average diameter of nano-particles.
基金supported by the National High Technology Research and Development Program of China(No.2011AA7014061)
文摘Considering the air-water interface and ocean water’s optical attenuation,the performance of quantum key distribution(QKD)based on air-water channel is studied.The effects of photons’various incident angles to air-water interface on quantum bit error rate(QBER)and the maximum secure transmission distance are analyzed.Taking the optical attenuation of ocean water into account,the performance bounds of QKD in different types of ocean water are discussed.The simulation results show that the maximum secure transmission distance of QKD gradually reduces as the incident angle from air to ocean water increases.In the clearest ocean water with the lowest attenuation,the maximum secure transmission distance of photons far exceeds the the working depth of underwater vehicles.In intermediate and murky ocean waters with higher attenuation,the secure transmission distance shortens,but the underwater vehicle can deploy other accessorial methods for QKD with perfect security.So the implementation of OKD between the satellite and the underwater vehicle is feasible.
基金ACKN0WLEDGMENT This work was supported by the National Natural Science Foundation of China （No.20374050） and SRFDP （No.20050358018）.
文摘Monte Carlo simulations were used to investigate the compatibilizing behaviors of multi-block copolymers with different architectures in A/B/（block copolymer） ternary blends. The volume fraction of homopolymer A, employed as the dispersed phase, was 19%. The simulations illustrate how a di- or multi-block copolymer aggregates at the interfaces and influences the phase behaviour of such incompatible polymer blends. The di-block copolymer chains tend to ＂stand＂ on the interface whereas the multi-block chains lie on the interface. In comparison with the di-block copolymer, the block copolymers with 4, or 10 blocks can occupy more areas on the interface, and thus the multi-block copolymers have higher efficiency for the retardation of the phase separation.
