Considering the interactions between fluid molecules and pore walls,variations in critical properties,capillary forces,and the influence of the adsorbed phase,this study investigates the phase behavior of the CO_(2)-s...Considering the interactions between fluid molecules and pore walls,variations in critical properties,capillary forces,and the influence of the adsorbed phase,this study investigates the phase behavior of the CO_(2)-shale oil within nanopores by utilizing a modified Peng-Robinson(PR)equation of state alongside a three-phase(gas-liquid-adsorbed)equilibrium calculation method.The results reveal that nano-confinement effects of the pores lead to a decrease in both critical temperature and critical pressure of fluids as pore size diminishes.Specifically,CO_(2) acts to inhibit the reduction of the critical temperature of the system while promoting the decrease in critical pressure.Furthermore,an increase in the mole fraction of CO_(2) causes the critical point of the system to shift leftward and reduces the area of the phase envelope.In the shale reservoirs of Block A in Gulong of the Daqing Oilfield,China,pronounced confinement effects are observed.At a pore diameter of 10 nm,reservoir fluids progressively exhibit characteristics typical of condensate gas reservoirs.Notably,the CO_(2) content in liquid in 10 nm pores increases by 20.0%compared to that in 100 nm pores,while the CO_(2) content in gas decreases by 10.8%.These findings indicate that confinement effects enhance CO_(2) mass transfer within nanopores,thereby facilitating CO_(2) sequestration and improving microscopic oil recovery.展开更多
Magnesium matrix composites with both high strength and ductility have been achieved by introducing pure Ti particles.However,the properties of the surfaces of the composites need to be improved by surface technology,...Magnesium matrix composites with both high strength and ductility have been achieved by introducing pure Ti particles.However,the properties of the surfaces of the composites need to be improved by surface technology,such as micro-arc oxidation(MAO).In this study,we investigated the influence of the Ti-reinforcement phase on coating growth and evolution by subjecting both AZ91 alloy and AZ91/Ti composite to MAO treatment using silicate-based and phosphate-based electrolytes.Results revealed that the Ti-reinforcement phase influenced the MAO process,altering discharge behavior,and leading to a decreased cell voltage.The vigorous discharge of the Ti-reinforcement phase induced the formation of coating discharge channels,concurrently dissolving and oxidizing Ti-reinforcement to produce a composite ceramic coating with TiO2.The MAO coating on the AZ91/Ti composite exhibited a dark blue macromorphology and distinctive local micromorphological anomalies.In silicate electrolyte,a“volcano-like”localized morphology centered on the discharge channel emerged.In contrast,treatment in phosphate-based electrolyte resulted in a coating morphology similar to typical porous ceramic coatings,with visible radial discharge micropores at the reinforcement phase location.Compared to the AZ91 alloy,the coating on the AZ91/Ti composite exhibited lower thickness and higher porosity.MAO treatment reduced the self-corrosion current density of the AZ91/Ti surface by two orders of magnitude.The silicate coating demonstrated better corrosion resistance than the phosphate coating,attributed to its lower porosity.The formation mechanism of MAO coatings on AZ91/Ti composites in phosphate-based and silicate-based electrolytes was proposed.展开更多
Comprehensive understanding of the direct transformation pathway from graphite to diamond under high temperature and high pressure has long been one of the fundamental goals in materials science.Despite considerable e...Comprehensive understanding of the direct transformation pathway from graphite to diamond under high temperature and high pressure has long been one of the fundamental goals in materials science.Despite considerable experimental and theoretical progress,current experimental studies have mainly focused on the local microstructural characterizations of recovered samples,which has certain limitations for hightemperature and high-pressure products,which often exhibit diversity.Here,we report on the pressure-induced phase transition behavior of natural single-crystal graphite under three distinct pressure-transmitting media from a macroscopic perspective using in situ two-dimensional Raman spectroscopy,scanning electron microscopy,and atomic force microscopy.The surface evolution process of graphite before and after the phase transition is captured,revealing that pressure-induced surface textures can impede the continuity of the phase transition process across the entire single crystal.Our results provide a fresh perspective for studying the phase transition behavior of graphite and greatly deepen our understanding of this behavior,which will be helpful in guiding further high-temperature and high-pressure syntheses of carbon allotropes.展开更多
The serrated flow behavior,known as the Portevin-Le Chatelier(PLC)effect,is commonly observed during high-temperature deformation.In this study,we report a serrated flow behavior in FeCoCrNiMo0.2 high-entropy alloy(HE...The serrated flow behavior,known as the Portevin-Le Chatelier(PLC)effect,is commonly observed during high-temperature deformation.In this study,we report a serrated flow behavior in FeCoCrNiMo0.2 high-entropy alloy(HEA),which is mediated by nano-twinning and phase transformation at cryogenic temperatures.During uniaxial tensile deformation at 77 K,the alloy exhibited the formation of high-density deformation nano-twinning,cross-twinning,stacking faults(SFs)and Lomer-Cottrell locks(L-C locks).Additionally,the lower stacking fault energy(SFE)at low temperatures promotes the formation of the 9R phase.The high-density twin boundaries effectively hinder dislocation movement,leading to the instability of plastic deformation and promoting the serrated flow behavior.Furthermore,the rapid and unstable transformation of the 9R phase contributes to the pronounced serrated flow behavior.Nano-twinning,SFs,cross-twinning,L-C locks and 9R phase collectively induce a dynamic Hall-Petch effect,enhancing the strength-ductility synergy and strain-hardening ability of deformed alloy at 77 K.Our work provides valuable insights into the mechanism of tensile deformation at cryogenic temperatures in single-phase FCC HEA.展开更多
The toughness of thermoplastic polymers such as polypropylene(PP)can be improved by adding elastomers-based toughening agents,and the phase morphology of these toughening agents is very important for the strength and ...The toughness of thermoplastic polymers such as polypropylene(PP)can be improved by adding elastomers-based toughening agents,and the phase morphology of these toughening agents is very important for the strength and toughness of PP.The low-temperature toughness of PP was improved by inserting high-density polyethylene(HDPE)between PP and polystyrene-b-ethylene-co-propyleneb-polystyrene(SEPS)to form an unusual SEPS@HDPE core–shell structure,with SEPS as the core and HDPE as the shell.Based on the microtopography and rheological behavior characterization,HDPE in PP/SEPS/HDPE composites was found to serve as an emulsifier,decrease the size of SEPS particles,and promote the homogeneous dispersion of dispersed phase particles in the matrix.An increase in the HDPE content shifted the toughening mechanism of PP composites from cavitation to matrix shear yielding.The reduction in the distance between the dispersed core–shell structure particles promoted shear yielding in the PP composites,leading to increased toughness.The creation of an intermediate HDPE layer with a moderate modulus was crucial for dispersing stress concentrations and significantly improving toughness without compromising the tensile strength.These findings will facilitate the fabrication of high-toughness PP products at low temperatures.展开更多
Shape memory alloys(SMAs)and shape memory ceramics(SMCs)exhibit high recovery ability due to the martensitic transformation,which complicates the fracture mechanism of SMAs and SMCs.The phase field method,as a powerfu...Shape memory alloys(SMAs)and shape memory ceramics(SMCs)exhibit high recovery ability due to the martensitic transformation,which complicates the fracture mechanism of SMAs and SMCs.The phase field method,as a powerful numerical simulation tool,can efficiently resolve the microstructural evolution,multi-field coupling effects,and fracture behavior of SMAs and SMCs.This review begins by presenting the fundamental theoretical framework of the fracture phase field method as applied to SMAs and SMCs,covering key aspects such as the phase field modeling of martensitic transformation and brittle fracture.Subsequently,it systematically examines the phase field simulations of fracture behaviors in SMAs and SMCs,with particular emphasis on how crystallographic orientation,grain size,and grain boundary properties influence the crack propagation.Additionally,the interplay between martensite transformation and fracture mechanisms is analyzed to provide deeper insights into the material responses under mechanical loading.Finally,the review explores future prospects and emerging trends in phase field simulations of SMA and SMC fracture behavior,along with potential advancements in the fracture phase field method itself,including multi-physics coupling and enhanced computational efficiency for large-scale simulations.展开更多
Shale reservoirs have abundant bedding structures,which deeply alter the mechanical properties of rocks,and thus affect the reservoir stimulation performance.Previous research mostly focuses on the effects of parallel...Shale reservoirs have abundant bedding structures,which deeply alter the mechanical properties of rocks,and thus affect the reservoir stimulation performance.Previous research mostly focuses on the effects of parallel bedding on fracture propagation,while the mechanical properties and mechanisms of fracture propagation remain unclear for rocks with complex wavy bedding(e.g.China’s continentalorigin Gulong shale).Herein,a mixed phase-field fracture model of the wavy-bedding shale was applied,based on the local tension-compression decomposition phase field method(PFM)and geometric structure generation algorithm for the bedding with controllable morphological features.The parametric analysis of fracture propagation behaviors in the case of abundant complex bedding structures showed that with wavy bedding,the vertical fracture propagation rate is far higher than the horizontal propagation rate.Moreover,the development of branch fractures is suppressed during the fracturing process of the wavy-bedding sample,and the stimulated volume is limited,which is different from the characteristic of parallel bedding that promotes horizontal fracture initiation and propagation.The results showed that larger amplitudes,higher frequencies,higher inclination angles,and larger strengths of wavy bedding all promote the formation of vertical penetrating fractures and suppress the growth of branch fractures.Under such circumstances,it is hard to create a well-connected fracture network after fracturing.This research may provide a theoretical basis for understanding fracture behaviors in rocks with such complex wavy bedding.展开更多
Microstructural characterization,mass loss tests,hydrogen evolution tests,electrochemical measurements,and corrosion morphology observations were conducted to investigate the effect of the secondary phases on the corr...Microstructural characterization,mass loss tests,hydrogen evolution tests,electrochemical measurements,and corrosion morphology observations were conducted to investigate the effect of the secondary phases on the corrosion behavior of the as-cast Mg−7Sn−1Zn−1Y(TZW711)alloy after solution treatment(T4)and aging treatment(T6).The results show that the T4-TZW711 alloy possesses the highest corrosion resistance in the early corrosion stage.This is because the dissolution of Mg2Sn reduces the cathodic current density and increases the charge transfer resistance(Rct).When the corrosion time is prolonged,the undissolved and clustered MgSnY phase will peel off from the T4-TZW711 alloy surface,thereby increasing the corrosion rate of the alloy.After aging treatment,the undissolved MgSnY phase is dispersed,which results in a lower localized corrosion sensitivity of T6-TZW711 alloy than that of the T4-TZW711 alloy,suggesting that the T6 treatment can enhance the corrosion resistance of Mg−7Sn−1Zn−1Y alloys.展开更多
1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7]...1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.展开更多
Microemulsions are usually used to prepare nanomaterials.The fo rmation behavior of microemulsions is crucial to the preparation of nanomaterials.Water in the internal phase is usually replaced by electrolyte solution...Microemulsions are usually used to prepare nanomaterials.The fo rmation behavior of microemulsions is crucial to the preparation of nanomaterials.Water in the internal phase is usually replaced by electrolyte solutions to prepare nanomaterials.Knowing the effects of electrolyte solution on the phase behavior of microemulsion is significant to the nanomaterial preparation.Microemulsion systems were studied by a conductivity method with cyclohexane as oil,Triton X-100 as surfactant,hexanol as cosurfactant,and deionized water or the electrolyte solutions of Cu(Ac)_(2)and Zn(Ac)_(2)as aqueous phases.The results showed that the replacement of water with electrolyte solution had a strong effect on the phase behavior of microemulsion system.The O/W microemulsion zone in water system was not observed in the studied electrolyte system.The shape and area of the corresponding phase zone in electrolyte system were different from that in water system.The microemulsion regions of electrolyte solution systems were always larger than that of water system.Zn(Ac)_(2)showed a larger microemulsion region than Cu(Ac)_(2)at 0.1 mol·L^(-1).The microemulsion phase region formed by 0.1 mol·L^(-1)Zn(Ac)_(2)+0.1 mol·L^(-1)Cu(Ac)_(2)was smaller than that formed by 0.1 mol·L^(-1)Zn(Ac)_(2)or 0.1 mol·L^(-1)Cu(Ac)_(2)lonely.With the increase of electrolyte concentration in the electrolyte solution and the rise of temperature,the microemulsion region shrank gradually.The changes of interactions between different components in the system should be responsible to the variation of phase behavior.The results provide important information for the microemulsion system with electrolyte solution as aqueous phase.展开更多
The effects of temperature and Re content on the mechanical properties,dislocation morphology,and deformation mechanism of γ-γ′phases nickel-based single crystal superalloys are investigated by using the molecular ...The effects of temperature and Re content on the mechanical properties,dislocation morphology,and deformation mechanism of γ-γ′phases nickel-based single crystal superalloys are investigated by using the molecular dynamics method through the model of γ-γ′phases containing hole defect.The addition of Re makes the dislocation distribution tend towards the γ phase.The higher the Re content,the earlier theγphase yields,while the γ′phase yields later.Dislocation bends under the combined action of the applied force and the resistance of the Re atoms to form a bend point.The Re atoms are located at the bend points and strengthen the alloy by fixing the dislocation and preventing it from cutting the γ′phase.Dislocations nucleate first in the γ phase,causing theγphase to deform plastically before the γ′phase.As the strain increases,the dislocation length first remains unchanged,then increases rapidly,and finally fluctuates and changes.The dislocation lengths in the γ phase are larger than those in the γ′phase at different temperatures.The dislocation length shows a decreasing tendency with the increase of the temperature.Temperature can affect movement of the dislocation,and superalloys have different plastic deformation mechanisms at low,medium and high temperatures.展开更多
The insufficient damping capabilities of aluminum alloy under low temperatures(<120℃)were addressed by developing high-damping laminated composites of NiTip/5052Al.This is achieved through the incorporation of var...The insufficient damping capabilities of aluminum alloy under low temperatures(<120℃)were addressed by developing high-damping laminated composites of NiTip/5052Al.This is achieved through the incorporation of varied pre-aging states of NiTi particles into the 5052Al matrix using a rolling composite technique.The aim is to enhance the application scope of aluminum alloy for vibration and noise reduction.The results demonstrated a distinct and integrated interface between the particle layer and the 5052Al alloy,with numerous interparticle interfaces within the particle layer.Increasing the aging temperature of the NiTi particles from 450 to 550℃ shifted the phase transition peaks of the composites to lower temperatures.The damping capacity of the laminated NiTip/5052Al composites notably surpasses that of the 5052Al alloy.At 28 and 66℃,the phase transformation damping peaks of the pre-aged NiTi particle layer reinforced 5052Al matrix composites are 1.93 and 2 times those of the 5052Al alloy at the corresponding temperatures,respectively.The collaborative impact of interparticle interface damping mechanism and the phase transformation damping mechanism of NiTi-reinforced particles significantly amplify the low-temperature damping performance of the laminated NiTip/5052Al composites.展开更多
The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosi...The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosite(Pb-J)were 130℃,30 g/L H_(2)SO_(4),15 g/L Fe^(3+),and an oxygen partial pressure of 0.4 MPa.Furthermore,increased Fe^(3+)concentration and oxygen partial pressure did not enhance jarosite formation.Conversely,lowering the temperature and increasing the H_(2)SO_(4) concentration facilitated PbSO_(4) formation and inhibited its further conversion to Pb-J.Additionally,the effects of potassium sulfate,sodium sulfate,and high concentrations of zinc sulfate on the phase transformation of galena were examined through leaching tests,XRD,SEM-EDS,and FT-IR analyses.All three sulfates inhibited the conversion of galena to Pb-J.Among these,potassium sulfate prevented Pb-J formation and converted it more thoroughly into potassium jarosite.However,high concentrations of zinc sulfate facilitated the crystallization of both PbSO_(4) and Pb-J,which altered the morphology of the product.Zinc ions coprecipitated with Pb-J,thereby integrating into the product.展开更多
Controllably tuning the sensing performance of flexible mechanical sensors is important for them to realize on-demand sensing of various mechanical stimuli in different application scenarios.However,current regulating...Controllably tuning the sensing performance of flexible mechanical sensors is important for them to realize on-demand sensing of various mechanical stimuli in different application scenarios.However,current regulating strategies focus on the construction process of individual sensors,the response performance of the as-formed sensors is still hard to autonomously tune with external stimulus changes like human skin.Here,we propose a new strategy that realizes post-tuning of the sensing performance by introducing a temperature-dependent phase transition elastomer into the sensing film.Through an interfacially confined photopolymerization reaction,a graphene-based phase-transition elastomeric(GPTE)film with a robust interface and excellent conductivity is well-formed at the water/air interface.Benefiting from the crystallization-melt dynamic switching in the elastomer network,the GPTE film could experience the reversible transformation between soft(1.65 MPa)and stiff(12.27MPa)states,showing huge changes of elastic modulus up to seven times near the phase transition temperature(28.5℃).Furthermore,the GPTE film is designed into a suspended perceptual configuration realizing the dynamic detection of 3D deformation adapted to temperature changes with up to 3.5-fold difference in response sensitivity.Finally,the self-adaptive sensing behavior of temperature-mediated 3D deformation is demonstrated by the effective detection of the dynamic stimulation process of cold and hot water droplets by the GPTE suspended film.The proposed strategy of phase transition-induced post-tuning of sensing performance could greatly facilitate flexible mechanical sensors towards a more intelligent one.展开更多
This study presents a two-dimensional,transient model to simulate the flow and thermal behavior of CO_(2) within a fracturing wellbore.The model accounts for high-velocity flow within the tubing and radial heat exchan...This study presents a two-dimensional,transient model to simulate the flow and thermal behavior of CO_(2) within a fracturing wellbore.The model accounts for high-velocity flow within the tubing and radial heat exchange between the wellbore and surrounding formation.It captures the temporal evolution of temperature,pressure,flow velocity,and fluid density,enabling detailed analysis of phase transitions along different tubing sections.The influence of key operational and geological parameters,including wellhead pressure,injection velocity,inlet temperature,and formation temperature gradient,on the wellbore’s thermal and pressure fields is systematically investigated.Results indicate that due to intense convective transport by the high-speed CO_(2) flow,the temperature and velocity within the tubing are primarily governed by the inlet temperature and injection velocity,with relatively minor influence from radial heat transfer with the formation.The pressure,flow velocity,and density of CO_(2) within the tubing are strongly dependent on wellhead conditions.Frictional losses and well depth contribute to pressure variations,particularly in the horizontal section of the wellbore,where a noticeable pressurization effect increases the fluid density.During injection,liquid CO_(2) initially undergoes a rapid transition to a supercritical state,with the depth at which this phase change occurs stabilizing as injection progresses.展开更多
The deformation behavior of the as-extruded Mg-Y-Ni alloys with different volume fraction of long period stacking ordered(LPSO)phase during tension and compression was investigated by in-situ synchrotron diffraction.T...The deformation behavior of the as-extruded Mg-Y-Ni alloys with different volume fraction of long period stacking ordered(LPSO)phase during tension and compression was investigated by in-situ synchrotron diffraction.The micro-yielding,macro-yielding,tension-compression asymmetry and strain hardening behavior of the alloys were explored by combining with deformation mechanisms.The micro-yielding is dominated by basal slip of dynamic recrystallized(DRXed)grains in tension,while it is dominated by extension twinning of non-dynamic recrystallized(non-DRXed)grains in compression.At macro-yielding,the non-DRXed grains are still elastic deformed in tension and the basal slip of DRXed grains in compression are activated.Meanwhile,the LPSO phase still retains elastic deformation,but can bear more load,so the higher the volume fraction of hard LPSO phase,the higher the tensile/compressive macro-yield strength of the alloys.Benefiting from the low volume fraction of the non-DRXed grains and the delay effect of LPSO andγphases on extension twinning,the as-extruded alloys exhibit excellent tension-compression symmetry.When the volume fraction of LPSO phase reaches∼50%,tension-compression asymmetry is reversed,which is due to the fact that the LPSO phase is stronger in compression than in tension.The tensile strain hardening behavior is dominated by dislocation slip,while the dominate mechanism for compressive strain hardening changes from twinning in theα-Mg grains to kinking of the LPSO phase with increasing volume fraction of LPSO phase.The activation of kinking leads to the constant compressive strain hardening rate of∼2500 MPa,which is significantly higher than the tensile strain hardening rate.展开更多
Due to the important role ofδphase's quantity and morphology in the mechanical and fatigue properties of Inconel 718 alloy and its components,it is necessary to renew insights into the effect of cold deformation ...Due to the important role ofδphase's quantity and morphology in the mechanical and fatigue properties of Inconel 718 alloy and its components,it is necessary to renew insights into the effect of cold deformation on theδphase precipitation,especially on the morphology evolution.Therefore,the nucleation and growth behavior ofδphase in cold-rolled Inconel 718 alloy during aging were investigated.The results show that the precipitation rate and volume fraction ofδphase increase with increasing the cold rolling reduction from 10%to 50%.The volume fraction ofδphase reaches equilibrium after 5 h,remaining at 5.98%,6.52%,and 6.79%under different rolling reductions(10%,30%,and 50%),respectively.The nucleation ofδphase mainly occurs on different sites(grain boundaries,new twin boundaries and old twin boundaries)under 10%rolling reduction,whileδphase mainly nucleates on the new grain boundaries of static recrystallization due to 50%rolling reduction.And the growth ofδphase undergoes a process of alternate orientation growth from spherical(nucleation)→short rod(longitudinal orientation growth)→short rod(radial orientation growth)→dynamic equilib-rium.Under 10%rolling reduction,δphase tends to grow into the matrix,while under 50%rolling reduction,the orientation grows faster and is easily affected by the grain boundary curvature.展开更多
The phase equilibrium and mechanical behaviors of natural gas hydrate-bearing sediment are essential for gas recovery from hydrate reservoirs.In heating closed systems,the temperature-pressure path of hydrate-bearing ...The phase equilibrium and mechanical behaviors of natural gas hydrate-bearing sediment are essential for gas recovery from hydrate reservoirs.In heating closed systems,the temperature-pressure path of hydrate-bearing sediment deviates from that of pure bulk hydrate,reflecting the porous media effect in phase equilibrium.A generalized phase equilibrium equation was established for hydrate-bearing sediments,which indicates that both capillary and osmotic pressures cause the phase equilibrium curve to shift leftward on the temperature-pressure plane.In contrast to bulk hydrate,hydrate-bearing sediment always contains a certain amount of unhydrated water,which keeps phase equilibrium with the hydrate within the hydrate stability field.With changes in temperature and pressure,a portion of pore hydrate and unhydrated water may transform into each other,affecting the shear strength of hydrate-bearing sediment.A shear strength model is proposed to consider not only hydrate saturation but also the change in temperature and pressure of hydrate-bearing sediment.The model is validated by experimental data with various hydrate saturation,temperature and pressure conditions.The deformation induced by partial dissociation was studied through depressurization tests under constant effective stress.The reduction in gas pressure within the hydrate stability field indeed caused sediment deformation.The dissociation-induced deformation can be reasonably estimated as the difference in volume between hydrate-bearing and hydrate-free sediments from the compression curves.展开更多
Efficient capture,safe storage and release of tritium from the international thermonuclear experimental reactor(ITER) reaction exhaust gas is a perplexing problem,and the development of an efficient tritium-getter mat...Efficient capture,safe storage and release of tritium from the international thermonuclear experimental reactor(ITER) reaction exhaust gas is a perplexing problem,and the development of an efficient tritium-getter material with ultra-low hydrogenation equilibrium pressure is considered as a reliable way.In this work,Zr_(2)Co alloy was selected as a tritium-getter material and prepared through induction levitation melting.Fundamental performance test results show that Zr_(2)Co exhibits an ultra-low hydrogenation equilibrium pressure of 3.22 × 10^(-6) Pa at 25℃ and excellent hydriding kinetics under a low hydrogen pressure of 0.005 MPa.Interestingly,unique phase transition behaviors were presented in Zr_(2)Co-H system.Specifically,Zr_(2)CoH_(5) formed by Zr_(2)Co hydrogenated at room temperature is initially decomposed into ZrH_(2) and ZrCoH_(3) at200 ℃.With the temperature increasing to 350 ℃,ZrCoH_(3)is dehydrogenated to ZrCo,and then ZrCo further reacts with ZrH_(2) at 650 ℃ to reform Zr_(2)Co and hydrogen.Among the staged phase transition pathways during dehydrogenation,the decomposition of Zr_(2)CoH_(5) occurs preferentially,which is well accordance with both the smallest reaction energy barrier and the maximum reaction spontaneity that are determined respectively from kinetics activation energy and thermodynamics Gibbs free energy.Furthermore,first principles calculation results indicate that the stronger binding of hydrogen in interstitial environments of ZrCoH_(3)and ZrH_(2) triggers the hydrogen-stabilized phase transformation of Zr_(2)CoH_(5).The unique phase transition mechanisms in Zr_(2)Co-H system can shed light on the further exploration and regulation of analogous staged phase transition of hydrogen storage materials.展开更多
NiTiCu thin walls were produced by twin-wire arc additive manufacturing(T-WAAM)using commercial NiTi and Cu wires as the feedstock materials.This approach aims to solve the problems typically associated with large pha...NiTiCu thin walls were produced by twin-wire arc additive manufacturing(T-WAAM)using commercial NiTi and Cu wires as the feedstock materials.This approach aims to solve the problems typically associated with large phase transformation hysteresis in NiTi shape memory alloys.The microstructure,mechanical properties,and phase transformation behavior of the as-deposited NiTiCu alloy were comprehensively examined.The results re-vealed that the as-deposited NiTiCu alloy was well-formed,with its microstructure showed columnar,equiaxed,and needle-like grains,depending on the location within the deposited walls.The microhardness gradually in-creased from the first to the third layer.The Cu content was 20.80 at%,and Cu-based precipitates were formed in the as-deposited NiTiCu.The volume fractions and lattice parameters of the matrix and precipitates in the as-deposited NiTiCu material were analyzed using high-energy synchrotron X-ray diffraction.The martensitic phase was identified as a B19 crystal structure,and the as-deposited NiTiCu underwent a one-step B2-B19 phase transformation.The tensile strength and fracture strain were approximately 232 MPa and 3.72%,respectively.In particular,the addition of Cu narrowed the phase transformation hysteresis of the as-deposited NiTiCu alloy from 24.4 to 7.1◦C compared with conventional binary NiTi alloys.This study expands the potential of T-WAAM in modifying the phase transformation behavior of NiTi-based ternary alloys.展开更多
基金Supported by the National Natural Science Foundation of China Joint Fund(U22B2075).
文摘Considering the interactions between fluid molecules and pore walls,variations in critical properties,capillary forces,and the influence of the adsorbed phase,this study investigates the phase behavior of the CO_(2)-shale oil within nanopores by utilizing a modified Peng-Robinson(PR)equation of state alongside a three-phase(gas-liquid-adsorbed)equilibrium calculation method.The results reveal that nano-confinement effects of the pores lead to a decrease in both critical temperature and critical pressure of fluids as pore size diminishes.Specifically,CO_(2) acts to inhibit the reduction of the critical temperature of the system while promoting the decrease in critical pressure.Furthermore,an increase in the mole fraction of CO_(2) causes the critical point of the system to shift leftward and reduces the area of the phase envelope.In the shale reservoirs of Block A in Gulong of the Daqing Oilfield,China,pronounced confinement effects are observed.At a pore diameter of 10 nm,reservoir fluids progressively exhibit characteristics typical of condensate gas reservoirs.Notably,the CO_(2) content in liquid in 10 nm pores increases by 20.0%compared to that in 100 nm pores,while the CO_(2) content in gas decreases by 10.8%.These findings indicate that confinement effects enhance CO_(2) mass transfer within nanopores,thereby facilitating CO_(2) sequestration and improving microscopic oil recovery.
基金supported by the Guangdong Major Project of Basic and Applied Basic Research(Grant No.2020B0301030006).
文摘Magnesium matrix composites with both high strength and ductility have been achieved by introducing pure Ti particles.However,the properties of the surfaces of the composites need to be improved by surface technology,such as micro-arc oxidation(MAO).In this study,we investigated the influence of the Ti-reinforcement phase on coating growth and evolution by subjecting both AZ91 alloy and AZ91/Ti composite to MAO treatment using silicate-based and phosphate-based electrolytes.Results revealed that the Ti-reinforcement phase influenced the MAO process,altering discharge behavior,and leading to a decreased cell voltage.The vigorous discharge of the Ti-reinforcement phase induced the formation of coating discharge channels,concurrently dissolving and oxidizing Ti-reinforcement to produce a composite ceramic coating with TiO2.The MAO coating on the AZ91/Ti composite exhibited a dark blue macromorphology and distinctive local micromorphological anomalies.In silicate electrolyte,a“volcano-like”localized morphology centered on the discharge channel emerged.In contrast,treatment in phosphate-based electrolyte resulted in a coating morphology similar to typical porous ceramic coatings,with visible radial discharge micropores at the reinforcement phase location.Compared to the AZ91 alloy,the coating on the AZ91/Ti composite exhibited lower thickness and higher porosity.MAO treatment reduced the self-corrosion current density of the AZ91/Ti surface by two orders of magnitude.The silicate coating demonstrated better corrosion resistance than the phosphate coating,attributed to its lower porosity.The formation mechanism of MAO coatings on AZ91/Ti composites in phosphate-based and silicate-based electrolytes was proposed.
基金support from the National Science Fund for Distinguished Young Scholars(Grant No.T2225027)the NSAF(Grant No.U1930401)+1 种基金the National Key R&D Program of China(MOST)(Grant No.2023YFA1406500)the National Natural Science Foundation of China(NSFC)(Grant No.61674045).
文摘Comprehensive understanding of the direct transformation pathway from graphite to diamond under high temperature and high pressure has long been one of the fundamental goals in materials science.Despite considerable experimental and theoretical progress,current experimental studies have mainly focused on the local microstructural characterizations of recovered samples,which has certain limitations for hightemperature and high-pressure products,which often exhibit diversity.Here,we report on the pressure-induced phase transition behavior of natural single-crystal graphite under three distinct pressure-transmitting media from a macroscopic perspective using in situ two-dimensional Raman spectroscopy,scanning electron microscopy,and atomic force microscopy.The surface evolution process of graphite before and after the phase transition is captured,revealing that pressure-induced surface textures can impede the continuity of the phase transition process across the entire single crystal.Our results provide a fresh perspective for studying the phase transition behavior of graphite and greatly deepen our understanding of this behavior,which will be helpful in guiding further high-temperature and high-pressure syntheses of carbon allotropes.
基金supported by the National Natural Science Foundation of China(Nos.52474403,52364050 and 52301137)Guizhou Provincial Program on Commercialization of Scientific and Technological Achievements(No.[2023]001)+2 种基金Guizhou Province Science and Technology Project(No.[2022]050)Guiyang city Science and Technology Project(No.[2023]48-16)the Central Government in Guidance of Local Science and Technology Development Funds(No.[2024]032).
文摘The serrated flow behavior,known as the Portevin-Le Chatelier(PLC)effect,is commonly observed during high-temperature deformation.In this study,we report a serrated flow behavior in FeCoCrNiMo0.2 high-entropy alloy(HEA),which is mediated by nano-twinning and phase transformation at cryogenic temperatures.During uniaxial tensile deformation at 77 K,the alloy exhibited the formation of high-density deformation nano-twinning,cross-twinning,stacking faults(SFs)and Lomer-Cottrell locks(L-C locks).Additionally,the lower stacking fault energy(SFE)at low temperatures promotes the formation of the 9R phase.The high-density twin boundaries effectively hinder dislocation movement,leading to the instability of plastic deformation and promoting the serrated flow behavior.Furthermore,the rapid and unstable transformation of the 9R phase contributes to the pronounced serrated flow behavior.Nano-twinning,SFs,cross-twinning,L-C locks and 9R phase collectively induce a dynamic Hall-Petch effect,enhancing the strength-ductility synergy and strain-hardening ability of deformed alloy at 77 K.Our work provides valuable insights into the mechanism of tensile deformation at cryogenic temperatures in single-phase FCC HEA.
基金supported by the Taiyuan Major Science and Technology Project Fund in 2021,Fund for Shanxi“1331 Project,”Key Research and Development Program of Shanxi Province(202102040201011)the Zhanjiang Marine Equipment and Marine Biological Industry Unveiled the Talent Team Project(2021E05034).
文摘The toughness of thermoplastic polymers such as polypropylene(PP)can be improved by adding elastomers-based toughening agents,and the phase morphology of these toughening agents is very important for the strength and toughness of PP.The low-temperature toughness of PP was improved by inserting high-density polyethylene(HDPE)between PP and polystyrene-b-ethylene-co-propyleneb-polystyrene(SEPS)to form an unusual SEPS@HDPE core–shell structure,with SEPS as the core and HDPE as the shell.Based on the microtopography and rheological behavior characterization,HDPE in PP/SEPS/HDPE composites was found to serve as an emulsifier,decrease the size of SEPS particles,and promote the homogeneous dispersion of dispersed phase particles in the matrix.An increase in the HDPE content shifted the toughening mechanism of PP composites from cavitation to matrix shear yielding.The reduction in the distance between the dispersed core–shell structure particles promoted shear yielding in the PP composites,leading to increased toughness.The creation of an intermediate HDPE layer with a moderate modulus was crucial for dispersing stress concentrations and significantly improving toughness without compromising the tensile strength.These findings will facilitate the fabrication of high-toughness PP products at low temperatures.
基金supported by the National Natural Science Foundation of China(12202294)the Sichuan Science and Technology Program(2024NSFSC1346).
文摘Shape memory alloys(SMAs)and shape memory ceramics(SMCs)exhibit high recovery ability due to the martensitic transformation,which complicates the fracture mechanism of SMAs and SMCs.The phase field method,as a powerful numerical simulation tool,can efficiently resolve the microstructural evolution,multi-field coupling effects,and fracture behavior of SMAs and SMCs.This review begins by presenting the fundamental theoretical framework of the fracture phase field method as applied to SMAs and SMCs,covering key aspects such as the phase field modeling of martensitic transformation and brittle fracture.Subsequently,it systematically examines the phase field simulations of fracture behaviors in SMAs and SMCs,with particular emphasis on how crystallographic orientation,grain size,and grain boundary properties influence the crack propagation.Additionally,the interplay between martensite transformation and fracture mechanisms is analyzed to provide deeper insights into the material responses under mechanical loading.Finally,the review explores future prospects and emerging trends in phase field simulations of SMA and SMC fracture behavior,along with potential advancements in the fracture phase field method itself,including multi-physics coupling and enhanced computational efficiency for large-scale simulations.
基金supported by the Technology Project of CNPC(Grant No.2023ZZ08)the National Natural Science Foundation of China(Grant No.52274058)the USTC Research Funds of the Double First-Class Initiative(Grant No.YD2090002025).
文摘Shale reservoirs have abundant bedding structures,which deeply alter the mechanical properties of rocks,and thus affect the reservoir stimulation performance.Previous research mostly focuses on the effects of parallel bedding on fracture propagation,while the mechanical properties and mechanisms of fracture propagation remain unclear for rocks with complex wavy bedding(e.g.China’s continentalorigin Gulong shale).Herein,a mixed phase-field fracture model of the wavy-bedding shale was applied,based on the local tension-compression decomposition phase field method(PFM)and geometric structure generation algorithm for the bedding with controllable morphological features.The parametric analysis of fracture propagation behaviors in the case of abundant complex bedding structures showed that with wavy bedding,the vertical fracture propagation rate is far higher than the horizontal propagation rate.Moreover,the development of branch fractures is suppressed during the fracturing process of the wavy-bedding sample,and the stimulated volume is limited,which is different from the characteristic of parallel bedding that promotes horizontal fracture initiation and propagation.The results showed that larger amplitudes,higher frequencies,higher inclination angles,and larger strengths of wavy bedding all promote the formation of vertical penetrating fractures and suppress the growth of branch fractures.Under such circumstances,it is hard to create a well-connected fracture network after fracturing.This research may provide a theoretical basis for understanding fracture behaviors in rocks with such complex wavy bedding.
基金National Natural Science Foundation of China(Nos.52301041,52022017,52065009,52371005)Special Fund for Special Posts of Guizhou University,China(No.[2023]26)+1 种基金Science and Technology Planning Project of Guizhou Province,China(No.ZK2021269)Fundamental Research Funds for the Central Universities,China(No.DUT23YG104)。
文摘Microstructural characterization,mass loss tests,hydrogen evolution tests,electrochemical measurements,and corrosion morphology observations were conducted to investigate the effect of the secondary phases on the corrosion behavior of the as-cast Mg−7Sn−1Zn−1Y(TZW711)alloy after solution treatment(T4)and aging treatment(T6).The results show that the T4-TZW711 alloy possesses the highest corrosion resistance in the early corrosion stage.This is because the dissolution of Mg2Sn reduces the cathodic current density and increases the charge transfer resistance(Rct).When the corrosion time is prolonged,the undissolved and clustered MgSnY phase will peel off from the T4-TZW711 alloy surface,thereby increasing the corrosion rate of the alloy.After aging treatment,the undissolved MgSnY phase is dispersed,which results in a lower localized corrosion sensitivity of T6-TZW711 alloy than that of the T4-TZW711 alloy,suggesting that the T6 treatment can enhance the corrosion resistance of Mg−7Sn−1Zn−1Y alloys.
基金supported by the National Key R&D Pro-gram of China(No.2022YFB3805701)National Natural Science Foundation of China(NSFC)(No.52371182,51701052,52192592,52192593)+1 种基金Young Elite Scientists Sponsorship Program by CAST(No.2019QNRC001)the Heilongjiang Touyan Innovation Team Program.
文摘1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.
基金funded by the National Natural Science Foundation of China(22078203)fundamental research funds for the central universities(2022SCUH0041)。
文摘Microemulsions are usually used to prepare nanomaterials.The fo rmation behavior of microemulsions is crucial to the preparation of nanomaterials.Water in the internal phase is usually replaced by electrolyte solutions to prepare nanomaterials.Knowing the effects of electrolyte solution on the phase behavior of microemulsion is significant to the nanomaterial preparation.Microemulsion systems were studied by a conductivity method with cyclohexane as oil,Triton X-100 as surfactant,hexanol as cosurfactant,and deionized water or the electrolyte solutions of Cu(Ac)_(2)and Zn(Ac)_(2)as aqueous phases.The results showed that the replacement of water with electrolyte solution had a strong effect on the phase behavior of microemulsion system.The O/W microemulsion zone in water system was not observed in the studied electrolyte system.The shape and area of the corresponding phase zone in electrolyte system were different from that in water system.The microemulsion regions of electrolyte solution systems were always larger than that of water system.Zn(Ac)_(2)showed a larger microemulsion region than Cu(Ac)_(2)at 0.1 mol·L^(-1).The microemulsion phase region formed by 0.1 mol·L^(-1)Zn(Ac)_(2)+0.1 mol·L^(-1)Cu(Ac)_(2)was smaller than that formed by 0.1 mol·L^(-1)Zn(Ac)_(2)or 0.1 mol·L^(-1)Cu(Ac)_(2)lonely.With the increase of electrolyte concentration in the electrolyte solution and the rise of temperature,the microemulsion region shrank gradually.The changes of interactions between different components in the system should be responsible to the variation of phase behavior.The results provide important information for the microemulsion system with electrolyte solution as aqueous phase.
基金Project supported by the Xi’an Science and Technology Plan Project of Shaanxi Province of China(Grant No.23GXFW0086).
文摘The effects of temperature and Re content on the mechanical properties,dislocation morphology,and deformation mechanism of γ-γ′phases nickel-based single crystal superalloys are investigated by using the molecular dynamics method through the model of γ-γ′phases containing hole defect.The addition of Re makes the dislocation distribution tend towards the γ phase.The higher the Re content,the earlier theγphase yields,while the γ′phase yields later.Dislocation bends under the combined action of the applied force and the resistance of the Re atoms to form a bend point.The Re atoms are located at the bend points and strengthen the alloy by fixing the dislocation and preventing it from cutting the γ′phase.Dislocations nucleate first in the γ phase,causing theγphase to deform plastically before the γ′phase.As the strain increases,the dislocation length first remains unchanged,then increases rapidly,and finally fluctuates and changes.The dislocation lengths in the γ phase are larger than those in the γ′phase at different temperatures.The dislocation length shows a decreasing tendency with the increase of the temperature.Temperature can affect movement of the dislocation,and superalloys have different plastic deformation mechanisms at low,medium and high temperatures.
基金National Natural Science Foundation of China (No. 52061011)Guangxi Natural Science Foundation,China (No. 2022GXNSFAA035574)Innovation Project of Guangxi Graduate Education,China (No. YCSW2023361)。
文摘The insufficient damping capabilities of aluminum alloy under low temperatures(<120℃)were addressed by developing high-damping laminated composites of NiTip/5052Al.This is achieved through the incorporation of varied pre-aging states of NiTi particles into the 5052Al matrix using a rolling composite technique.The aim is to enhance the application scope of aluminum alloy for vibration and noise reduction.The results demonstrated a distinct and integrated interface between the particle layer and the 5052Al alloy,with numerous interparticle interfaces within the particle layer.Increasing the aging temperature of the NiTi particles from 450 to 550℃ shifted the phase transition peaks of the composites to lower temperatures.The damping capacity of the laminated NiTip/5052Al composites notably surpasses that of the 5052Al alloy.At 28 and 66℃,the phase transformation damping peaks of the pre-aged NiTi particle layer reinforced 5052Al matrix composites are 1.93 and 2 times those of the 5052Al alloy at the corresponding temperatures,respectively.The collaborative impact of interparticle interface damping mechanism and the phase transformation damping mechanism of NiTi-reinforced particles significantly amplify the low-temperature damping performance of the laminated NiTip/5052Al composites.
基金Projects(2023AG05008,202302AB080012)supported by the Yunnan Major Scientific and Technological Program,ChinaProject(202405AC350015)supported by the Science and Technology Talent Programme of Yunnan Province,China。
文摘The phase transformation of galena in H_(2)SO_(4)-Fe_(2)(SO_(4))_(3) system under oxygen pressure was investigated.Results indicated that the critical conditions for the phase transformation of galena into lead jarosite(Pb-J)were 130℃,30 g/L H_(2)SO_(4),15 g/L Fe^(3+),and an oxygen partial pressure of 0.4 MPa.Furthermore,increased Fe^(3+)concentration and oxygen partial pressure did not enhance jarosite formation.Conversely,lowering the temperature and increasing the H_(2)SO_(4) concentration facilitated PbSO_(4) formation and inhibited its further conversion to Pb-J.Additionally,the effects of potassium sulfate,sodium sulfate,and high concentrations of zinc sulfate on the phase transformation of galena were examined through leaching tests,XRD,SEM-EDS,and FT-IR analyses.All three sulfates inhibited the conversion of galena to Pb-J.Among these,potassium sulfate prevented Pb-J formation and converted it more thoroughly into potassium jarosite.However,high concentrations of zinc sulfate facilitated the crystallization of both PbSO_(4) and Pb-J,which altered the morphology of the product.Zinc ions coprecipitated with Pb-J,thereby integrating into the product.
基金supported by the National Key Research and Development Program of China(No.2022YFC2805200)the National Natural Science Foundation of China(No.52373094)+4 种基金Zhejiang Provincial Natural Science Foundation(No.LR25E030004)Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2023313)Sino-German Mobility Program(No.M-0424),Ningbo Major Research and Development Plan Project(No.20241ZDYF020148)Ningbo International Cooperation(No.2023H019)Ningbo Science&Technology Bureau(No.2024QL003)。
文摘Controllably tuning the sensing performance of flexible mechanical sensors is important for them to realize on-demand sensing of various mechanical stimuli in different application scenarios.However,current regulating strategies focus on the construction process of individual sensors,the response performance of the as-formed sensors is still hard to autonomously tune with external stimulus changes like human skin.Here,we propose a new strategy that realizes post-tuning of the sensing performance by introducing a temperature-dependent phase transition elastomer into the sensing film.Through an interfacially confined photopolymerization reaction,a graphene-based phase-transition elastomeric(GPTE)film with a robust interface and excellent conductivity is well-formed at the water/air interface.Benefiting from the crystallization-melt dynamic switching in the elastomer network,the GPTE film could experience the reversible transformation between soft(1.65 MPa)and stiff(12.27MPa)states,showing huge changes of elastic modulus up to seven times near the phase transition temperature(28.5℃).Furthermore,the GPTE film is designed into a suspended perceptual configuration realizing the dynamic detection of 3D deformation adapted to temperature changes with up to 3.5-fold difference in response sensitivity.Finally,the self-adaptive sensing behavior of temperature-mediated 3D deformation is demonstrated by the effective detection of the dynamic stimulation process of cold and hot water droplets by the GPTE suspended film.The proposed strategy of phase transition-induced post-tuning of sensing performance could greatly facilitate flexible mechanical sensors towards a more intelligent one.
基金funded by National Natural Science Foundation of China(Mechanisms of proppant-carrying transport by magnetic cross-linked microparticle grids and their degradation patterns in CO_(2) fractured cracks).
文摘This study presents a two-dimensional,transient model to simulate the flow and thermal behavior of CO_(2) within a fracturing wellbore.The model accounts for high-velocity flow within the tubing and radial heat exchange between the wellbore and surrounding formation.It captures the temporal evolution of temperature,pressure,flow velocity,and fluid density,enabling detailed analysis of phase transitions along different tubing sections.The influence of key operational and geological parameters,including wellhead pressure,injection velocity,inlet temperature,and formation temperature gradient,on the wellbore’s thermal and pressure fields is systematically investigated.Results indicate that due to intense convective transport by the high-speed CO_(2) flow,the temperature and velocity within the tubing are primarily governed by the inlet temperature and injection velocity,with relatively minor influence from radial heat transfer with the formation.The pressure,flow velocity,and density of CO_(2) within the tubing are strongly dependent on wellhead conditions.Frictional losses and well depth contribute to pressure variations,particularly in the horizontal section of the wellbore,where a noticeable pressurization effect increases the fluid density.During injection,liquid CO_(2) initially undergoes a rapid transition to a supercritical state,with the depth at which this phase change occurs stabilizing as injection progresses.
基金supported by National Natural Science Foundation of China(no.U21A2047,no.51971076 and no.52001069).
文摘The deformation behavior of the as-extruded Mg-Y-Ni alloys with different volume fraction of long period stacking ordered(LPSO)phase during tension and compression was investigated by in-situ synchrotron diffraction.The micro-yielding,macro-yielding,tension-compression asymmetry and strain hardening behavior of the alloys were explored by combining with deformation mechanisms.The micro-yielding is dominated by basal slip of dynamic recrystallized(DRXed)grains in tension,while it is dominated by extension twinning of non-dynamic recrystallized(non-DRXed)grains in compression.At macro-yielding,the non-DRXed grains are still elastic deformed in tension and the basal slip of DRXed grains in compression are activated.Meanwhile,the LPSO phase still retains elastic deformation,but can bear more load,so the higher the volume fraction of hard LPSO phase,the higher the tensile/compressive macro-yield strength of the alloys.Benefiting from the low volume fraction of the non-DRXed grains and the delay effect of LPSO andγphases on extension twinning,the as-extruded alloys exhibit excellent tension-compression symmetry.When the volume fraction of LPSO phase reaches∼50%,tension-compression asymmetry is reversed,which is due to the fact that the LPSO phase is stronger in compression than in tension.The tensile strain hardening behavior is dominated by dislocation slip,while the dominate mechanism for compressive strain hardening changes from twinning in theα-Mg grains to kinking of the LPSO phase with increasing volume fraction of LPSO phase.The activation of kinking leads to the constant compressive strain hardening rate of∼2500 MPa,which is significantly higher than the tensile strain hardening rate.
基金The authors are grateful to the Province Natural Science Foundation of Zhejiang(Grant No.LQ19E050004)for financial support.The authors also graciously thank China Airlines Shenyang Liming Aeroengine Co.,Ltd.for aiding in providing the experimental Inconel 718 alloys.
文摘Due to the important role ofδphase's quantity and morphology in the mechanical and fatigue properties of Inconel 718 alloy and its components,it is necessary to renew insights into the effect of cold deformation on theδphase precipitation,especially on the morphology evolution.Therefore,the nucleation and growth behavior ofδphase in cold-rolled Inconel 718 alloy during aging were investigated.The results show that the precipitation rate and volume fraction ofδphase increase with increasing the cold rolling reduction from 10%to 50%.The volume fraction ofδphase reaches equilibrium after 5 h,remaining at 5.98%,6.52%,and 6.79%under different rolling reductions(10%,30%,and 50%),respectively.The nucleation ofδphase mainly occurs on different sites(grain boundaries,new twin boundaries and old twin boundaries)under 10%rolling reduction,whileδphase mainly nucleates on the new grain boundaries of static recrystallization due to 50%rolling reduction.And the growth ofδphase undergoes a process of alternate orientation growth from spherical(nucleation)→short rod(longitudinal orientation growth)→short rod(radial orientation growth)→dynamic equilib-rium.Under 10%rolling reduction,δphase tends to grow into the matrix,while under 50%rolling reduction,the orientation grows faster and is easily affected by the grain boundary curvature.
基金supported by the National Natural Science Foundation of China(Grant Nos.42171135 and 12262009)the“CUG Scholar”Scientific Research Funds at China University of Geosciences(Wuhan)(Project No.2022098).
文摘The phase equilibrium and mechanical behaviors of natural gas hydrate-bearing sediment are essential for gas recovery from hydrate reservoirs.In heating closed systems,the temperature-pressure path of hydrate-bearing sediment deviates from that of pure bulk hydrate,reflecting the porous media effect in phase equilibrium.A generalized phase equilibrium equation was established for hydrate-bearing sediments,which indicates that both capillary and osmotic pressures cause the phase equilibrium curve to shift leftward on the temperature-pressure plane.In contrast to bulk hydrate,hydrate-bearing sediment always contains a certain amount of unhydrated water,which keeps phase equilibrium with the hydrate within the hydrate stability field.With changes in temperature and pressure,a portion of pore hydrate and unhydrated water may transform into each other,affecting the shear strength of hydrate-bearing sediment.A shear strength model is proposed to consider not only hydrate saturation but also the change in temperature and pressure of hydrate-bearing sediment.The model is validated by experimental data with various hydrate saturation,temperature and pressure conditions.The deformation induced by partial dissociation was studied through depressurization tests under constant effective stress.The reduction in gas pressure within the hydrate stability field indeed caused sediment deformation.The dissociation-induced deformation can be reasonably estimated as the difference in volume between hydrate-bearing and hydrate-free sediments from the compression curves.
基金financially supported by the National Key Research and Development Program of China (No.2022YFE03170002)the National Natural Science Foundation of China (Nos.52071286 and U2030208)。
文摘Efficient capture,safe storage and release of tritium from the international thermonuclear experimental reactor(ITER) reaction exhaust gas is a perplexing problem,and the development of an efficient tritium-getter material with ultra-low hydrogenation equilibrium pressure is considered as a reliable way.In this work,Zr_(2)Co alloy was selected as a tritium-getter material and prepared through induction levitation melting.Fundamental performance test results show that Zr_(2)Co exhibits an ultra-low hydrogenation equilibrium pressure of 3.22 × 10^(-6) Pa at 25℃ and excellent hydriding kinetics under a low hydrogen pressure of 0.005 MPa.Interestingly,unique phase transition behaviors were presented in Zr_(2)Co-H system.Specifically,Zr_(2)CoH_(5) formed by Zr_(2)Co hydrogenated at room temperature is initially decomposed into ZrH_(2) and ZrCoH_(3) at200 ℃.With the temperature increasing to 350 ℃,ZrCoH_(3)is dehydrogenated to ZrCo,and then ZrCo further reacts with ZrH_(2) at 650 ℃ to reform Zr_(2)Co and hydrogen.Among the staged phase transition pathways during dehydrogenation,the decomposition of Zr_(2)CoH_(5) occurs preferentially,which is well accordance with both the smallest reaction energy barrier and the maximum reaction spontaneity that are determined respectively from kinetics activation energy and thermodynamics Gibbs free energy.Furthermore,first principles calculation results indicate that the stronger binding of hydrogen in interstitial environments of ZrCoH_(3)and ZrH_(2) triggers the hydrogen-stabilized phase transformation of Zr_(2)CoH_(5).The unique phase transition mechanisms in Zr_(2)Co-H system can shed light on the further exploration and regulation of analogous staged phase transition of hydrogen storage materials.
基金supported by National Natural Science Founda-tion of China(Grant No.52175292)Science and Technology Project of Sichuan Province(Grant Nos.23NSFJQ0064,2022YFQ0058)+2 种基金Guangdong Basic and Applied Basic Research Foundation(Grant No.2021B1515140048)JPO and JS acknowledge the funding by na-tional funds from Fundação para a Ciência e a Tecnologia(FCT),I.P.,within the scope of projects LA/P/0037/2020,UIDP/50025/2020,and UIDB/50025/2020 of the Associate Laboratory Institute of Nanostruc-tures,Nanomodelling,and Nanofabrication-i3NDESY(Hamburg,Germany),a member of the Helmholtz Associa-tion HGF,for providing the experimental facilities.Part of this study was conducted at PETRA III.The research leading to this result was sup-ported by project CALIPSOplus under Grant Agreement 730872 from the EU Framework Programme for Research and Innovation HORIZON 2020.
文摘NiTiCu thin walls were produced by twin-wire arc additive manufacturing(T-WAAM)using commercial NiTi and Cu wires as the feedstock materials.This approach aims to solve the problems typically associated with large phase transformation hysteresis in NiTi shape memory alloys.The microstructure,mechanical properties,and phase transformation behavior of the as-deposited NiTiCu alloy were comprehensively examined.The results re-vealed that the as-deposited NiTiCu alloy was well-formed,with its microstructure showed columnar,equiaxed,and needle-like grains,depending on the location within the deposited walls.The microhardness gradually in-creased from the first to the third layer.The Cu content was 20.80 at%,and Cu-based precipitates were formed in the as-deposited NiTiCu.The volume fractions and lattice parameters of the matrix and precipitates in the as-deposited NiTiCu material were analyzed using high-energy synchrotron X-ray diffraction.The martensitic phase was identified as a B19 crystal structure,and the as-deposited NiTiCu underwent a one-step B2-B19 phase transformation.The tensile strength and fracture strain were approximately 232 MPa and 3.72%,respectively.In particular,the addition of Cu narrowed the phase transformation hysteresis of the as-deposited NiTiCu alloy from 24.4 to 7.1◦C compared with conventional binary NiTi alloys.This study expands the potential of T-WAAM in modifying the phase transformation behavior of NiTi-based ternary alloys.
