Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro...Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro-structure has been applied on the micro-grinding tool.A morphology modeling has been established in this study to characterize the surface of microstructured micro-grinding tool,and the grinding performance of micro-structured micro-grinding tool has been analyzed through undeformed chip thickness,abrasive edge width,and effective distance between abrasives.Then deviation analysis,path optimization and parameter optimization of microchannel array precision grinding have been finished to improve processing quality and efficiency,and the deflection angle has the most obvious effects on the rectangular slot depth,micro-structured micro-grinding tool could reduce 10%surface roughness and 20%grinding force compared to original micro-grinding tool.Finally,the microchannel array has been machined with a size deviation of 2μm and surface roughness of 0.2μm.展开更多
High-performance 24CrNiMo steel was fabricated using Laser Powder Bed Fusion (LPBF). Subsequent quenching treatment was applied and the influence of quenching temperatures on micro-structure evolution and properties w...High-performance 24CrNiMo steel was fabricated using Laser Powder Bed Fusion (LPBF). Subsequent quenching treatment was applied and the influence of quenching temperatures on micro-structure evolution and properties was systematically characterised and analysed. The micro-structure of the as-built steel consisted of two parts. The first part comprised martensite with twins combined with ω-Fe nano-particles, and the second part consisted of lower bainite in the molten pool, as well as upper bainite, granular bainite and tempered martensite in the heat-affected zone. With the quenching temperatures varying from 800℃ to 950℃, the micro-structure gradually transformed from acicular ferrite + martensite to tempered martensite +θ-Fe3C carbides, and the grain size exhibited noticeable growth. Moreover, quenching treatments could eliminate the anisotropy and inhomogeneity of the micro-structure. The rod-shaped nanosized η-Fe2C and θ-Fe3C precipitates were clearly observed, which were converted from ω-Fe and distributed at multiple angles in the lath. The size and number of nano-precipitates, triggered by the high self-tempering degree of martensite, gradually increased. The relationships among grain size, the twins, dislocation density and nano-precipitation and the dramatically improved performance of quenched samples were analysed using strengthening mechanisms. After quenching at 850℃, the as-built 24CrNiMo steel attained ultra-high mechanical properties including hardness, Ultimate Tensile Strength (UTS), Elongation (El) and impact energy with values of 480.9 HV_(1), 1611.4 MPa, 9.8% and 42.8 J, respectively. Meanwhile, both the wear and thermal fatigue resistance increased by approximately 40%. This study demonstrated that LPBF-fabricated 24CrNiMo steel, with matching good performances, can be achieved using a subsequent one-step quenching process.展开更多
BACKGROUND Drug utilization research has an important role in assisting the healthcare administration to know,compute,and refine the prescription whose principal objective is to enable the rational use of drugs.Resear...BACKGROUND Drug utilization research has an important role in assisting the healthcare administration to know,compute,and refine the prescription whose principal objective is to enable the rational use of drugs.Research in developing nations relating to the cost of treatment is scarce when compared with developed countries.Thus,the drug utilization research studies from developing nations are most needed,and their number has been growing.AIM To evaluate patterns of utilization of antipsychotic drugs and direct medical cost analysis in patients newly diagnosed with schizophrenia.METHODS The present study was observational in type and based on a retrospective cohort to evaluate patterns of utilization of antipsychotic drugs using World Health Organization(WHO)core prescribing indicators and anatomical therapeutic chemical/defined daily dose indicators.We also calculated direct medical costs for a period of 6 months.RESULTS This study has found that atypical antipsychotics are the mainstay of treatment for schizophrenia in every age group and subcategories of schizophrenia.The evaluation based on WHO prescribing indicators showed a low average number of drugs per prescription and low prescribing frequency of antipsychotics from the National List of Essential Medicines 2015 and the WHO Essential Medicines List 2019.The total mean drug cost of our study was 1396 Indian rupees.The total mean cost due to the investigation in our study was 1017.34 Indian rupees.Therefore,the total mean direct medical cost incurred on patients in our study was 4337.28 Indian rupees.CONCLUSION The information from the present study can be used for reviewing and updating treatment policy at the institutional level.展开更多
In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and mat...In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and material properties of sample at various depths from the topmost surface were investigated by SEM, TEM, XRD, OM etc. The experimental results show that the gradient nano/micro-structure was introduced into the surface layer of over 100μm in thickness. The remarkable increase in hardness near the topmost surface was mainly attributed to the reduced grain size. The equiaxed nano-sized grains were in random orientation and the most of their boundaries were low-angle grain boundaries （LAGBs）. The coarse grains are refined into the few micro-sized grains by dislocation activities;deformation twinning was found to be the primary form for the formation of submicron grains;the formation of nanostructure was dominated by dislocation activities accompanied with rotation of grains in local region.展开更多
Nowadays,the superior detection performance of semiconductor neutron detectors is a challenging task.In this paper,we deal with a novel GaN micro-structured neutron detector(GaN-MSND)and compare three different method...Nowadays,the superior detection performance of semiconductor neutron detectors is a challenging task.In this paper,we deal with a novel GaN micro-structured neutron detector(GaN-MSND)and compare three different methods such as the method of modulating the trench depth,the method of introducing dielectric layer and p-type inversion region to improve the width of depletion region(W).It is observed that the intensity of electric field can be modulated by scaling the trench depth.On the other hand,the electron blocking region is formed in the detector enveloped with a dielectric layer.Furthermore,the introducing of p-type inversion region produces new p/n junction,which not only promotes the further expansion of the depletion region but also reduces the intensity of electric field produced by main junction.It can be realized that all these methods can considerably enhance the working voltage as well as W.Of them,the improvement on W of GaN-MSND with the p-type inversion region is the most significant and the value of W could reach 12.8μm when the carrier concentration of p-type inversion region is 10^17 cm^-3.Consequently,the value of W is observed to improve 200%for the designed GaN-MSND as compared with that without additional design.This work ensures to the researchers and scientific community the fabrication of GaN-MSND having superior detection limit in the field of intense radiation.展开更多
In this paper,we report the study of the process of fabricating a multi-layermetal micro-structure using UV-LIGA overlay technology,includingmask fabrication,substrate treatment,and UV-LIGA overlay processes.To solve ...In this paper,we report the study of the process of fabricating a multi-layermetal micro-structure using UV-LIGA overlay technology,includingmask fabrication,substrate treatment,and UV-LIGA overlay processes.To solve the process problems in the masking procedure,the swelling problemof the first layer of SU-8 thick photoresist was studied experimentally.The 5μmline-width compensation and closed 20μmand 30μmisolation strips were designed and fabricated around the micro-structure pattern.The pore problemin the Ni micro-electroforming layer was analyzed and the electroforming parameters were improved.The pH value of the electroforming solution should be controlled between 3.8 and 4.4 and the current density should be below 3 A/dm^2.To solve the problems of high inner stress and incomplete development of the micro-cylinder hole array with a diameter of 30μm,the lithography process was optimized.The pre-baking temperature was increased via gradient heating and rose every 5℃ from 65℃ to 85℃ and then remained at 85℃ for 50 min–1 h.In addition,the full contact exposure was used.Finally,a multi-layer metal micro-structure with high precision and good quality of microelectroforming layer was fabricated using UV-LIGA overlay technology.展开更多
A low-power CO_2 laser is used to deposit Fe powder and mixture of Fe andcarbon powder on substrates respectively, and the macro and micro-structure of the formed samplesare investigated. It is demonstrated that most ...A low-power CO_2 laser is used to deposit Fe powder and mixture of Fe andcarbon powder on substrates respectively, and the macro and micro-structure of the formed samplesare investigated. It is demonstrated that most grains of these samples are equi-axed. This isderived from the high nucleation velocity in the shallow melt pool besides rapid solidification ofthe liquid-state alloy or metal. Bainitic structure, combination of pearlite and ferrite structureand ferrite structure are seen respectively in the samples involving various amounts of carbon owingto no martensitic transformation in these small samples.展开更多
To obtain the form error of micro-structured surfaces robustly and accurately, a form er- ror evaluation method was developed based on the real coded genetic algorithm （RCGA）. The meth- od employed the average squar...To obtain the form error of micro-structured surfaces robustly and accurately, a form er- ror evaluation method was developed based on the real coded genetic algorithm （RCGA）. The meth- od employed the average squared distance as the matching criterion. The point to surface distance was achieved by use of iterative method and the modeling of RCGA for the surface matching was also presented in detail. Parameter selection for RCGA including the crossover rate and population size was discussed. Evaluation results of series simulated surfaces without form error show that this method can achieve the accuracy of root mean square deviation （ Sq ） less than 1 nm and surface pro- file error （ St ） less than 4 nm. Evaluation of the surfaces with different simulated errors illustrates that the proposed method can also robustly obtain the form error with nano-meter precision. The e- valuation of actual measured surfaces further indicates that the proposed method is capable of pre- cisely evaluating micro-structured surfaces.展开更多
Ni-rich layered material is a kind of high-capacity cathode to meet the requirement of electric vehicles.As for the typical LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) material,the particle formation is significant for electroche...Ni-rich layered material is a kind of high-capacity cathode to meet the requirement of electric vehicles.As for the typical LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) material,the particle formation is significant for electrochemical properties of the cathode.In this work,the structure,morphology,and electrochemical performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) secondary particles and single crystals were systematically studied.A lower Ni^(2+)/Ni^(3+)molar ratio of 0.66 and a lower residual alkali content of 0.228wt%were achieved on the surface of the single crystals.In addition,the single crystals showed a discharge capacity of 191.6 mAh/g at 0.2 C(~12 mAh/g lower than that of the secondary particles)and enhanced the electrochemical stability,especially when cycled at 50℃ and in a wider electrochemical window(between 3.0 and 4.4 V vs.Li+/Li).The LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) secondary particles were suitable for applications requiring high specific capacity,whereas single crystals exhibited better stability,indicating that they are more suitable for use in long life requested devices.展开更多
Adopting a nano-and micro-structuring approach to fully unleashing the genuine potential of electrode active material benefits in-depth understandings and research progress toward higher energy density electrochemical...Adopting a nano-and micro-structuring approach to fully unleashing the genuine potential of electrode active material benefits in-depth understandings and research progress toward higher energy density electrochemical energy stor-age devices at all technology readiness levels.Due to various challenging issues,especially limited stability,nano-and micro-structured(NMS)electrodes undergo fast electrochemical performance degradation.The emerging NMS scaffold design is a pivotal aspect of many electrodes as it endows them with both robustness and electrochemical performance enhancement,even though it only occupies comple-mentary and facilitating components for the main mechanism.However,extensive efforts are urgently needed toward optimizing the stereoscopic geometrical design of NMS scaffolds to minimize the volume ratio and maximize their functionality to fulfill the ever-increasing dependency and desire for energy power source supplies.This review will aim at highlighting these NMS scaffold design strategies,summariz-ing their corresponding strengths and challenges,and thereby outlining the potential solutions to resolve these challenges,design principles,and key perspectives for future research in this field.Therefore,this review will be one of the earliest reviews from this viewpoint.展开更多
The sub-vertical meso-and micro-structures and fabrics developed in coesite-bearing foliated eclogites in the Taohang （桃行） area, southeastern Shandong （山东）, China. The diagnostic structures and fabrics, includ...The sub-vertical meso-and micro-structures and fabrics developed in coesite-bearing foliated eclogites in the Taohang （桃行） area, southeastern Shandong （山东）, China. The diagnostic structures and fabrics, including penetrative foliation or mylonitic foliation containing mineral and stretching lineations, as well as sheath-like folds, appear to be the development of anastomosing UHP eciogite-facies shear belt arrays hosting massive eelogites. Textural relationships and mineral assem-blages indicate that the deformation of foliated eclogites developed closely after the formation of the massive eclogite, prior to the development of the granulite/amphibolite-facies symplectites and coronas, occurring over a very wide pressure range of （31-8）×10^2 MPa. It presents the structural records of the tectonometamorphic processes as being responsible for the earliest stages of exhumation of the UHP metamorphic rocks. Extensive regional field observations show that the meso-and micro-structures and fabrics recognized in the foliated eclogites at Taohang are remarkably similar or consistent in the whole Dabie （大别）-Sulu （苏鲁） UHP metamorphic belt. This article, thus, supports the idea that the earliest stages of exhumation of the UHP metamorphic rocks, from mantle depths to the Moho or the mantle-crust boundary layering, may be attributed mainly to a sub-vertical extrusion and ductile flow along the subduction channel, belonging to a syn-collision exhumation at about 235 to 220 Ma.展开更多
A novel flower-like hydrated magnesium carbonate hydroxide, Mg5 （CO3 ）4 （OH）2·4H2O, with micro-structure composed of individual thin nano-sheets was synthesized using a facile solution route without the use o...A novel flower-like hydrated magnesium carbonate hydroxide, Mg5 （CO3 ）4 （OH）2·4H2O, with micro-structure composed of individual thin nano-sheets was synthesized using a facile solution route without the use of template or organic surfactant. Reaction time has an important effect on the final morphology of the product. The micro-structure and morphology of Mg5 （CO3）4 （OH）2·4H2O were characterized by means of X-ray diffractometry （XRD）, fieldemission scanning electron microscopy（FE-SEM）. Brunauer-Emmett-Teller（BET） surface areas of the samples were also measured. The probable formation mechanism of flower-like micro-structure was discussed. It was found that Mg5 （CO3）4（ OH）2·4H2O with flower-like micro-structure was a novel and efficient catalyst for the synthesis of diphenyl carbonate （DPC） by transesterification of dimethyl carbonate （DMC） with phenol.展开更多
In this article, the convection dominated convection-diffusion problems with the periodic micro-structure are discussed. A two-scale finite element scheme based on the homogenization technique for this kind of problem...In this article, the convection dominated convection-diffusion problems with the periodic micro-structure are discussed. A two-scale finite element scheme based on the homogenization technique for this kind of problems is provided. The error estimates between the exact solution and the approximation solution, of the homogenized equation or the two-scale finite element scheme are analyzed. It is shown that the scheme provided in this article is convergent for any fixed diffusion coefficient 5, and it may be convergent independent of δ under some conditions. The numerical results demonstrating the theoretical results are presented in this article.展开更多
A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We empl...A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We employ a diffuse interface model that incorporates the mechanism of surface diffusion. The mechanism of the fabrication is systematically integrated for high reliability of computational analysis. A semi-implicit Fourier spectral scheme is applied for high efficiency and numerical stability. Moreover, the theoretical analysis provides the guidance that is ordered by the fundamental geometrical design parameters to guide different fabrications of SON structures. The performed simulations suggest a substantial potential of the presented model for a reliable design technology of nano/micro-fabrications.展开更多
A new standard parametric modeling method of the micro-structure of plain woven composite is proposed. It is based on good analysis of the mechanical property of the yarn, weaving law of plain woven, and other factors...A new standard parametric modeling method of the micro-structure of plain woven composite is proposed. It is based on good analysis of the mechanical property of the yarn, weaving law of plain woven, and other factors. The method implements a woven fabric composite visual engineering modeling process standardization, and it gives five steps to calculate the key micro-structural parameters of the yarn including the cross-section and the trajectory of the central Line. On the basis, the digital model of a plain woven composite has been constructed. The experimental result shows that the forecast for the mechanical property of the model using finite-element simulation analysis is consistent with the actual value. The shape and the structure of the model are also consistent with the solid.展开更多
With advent of servo-controlled stiff testing machines, it is now possible to conduct tests on a rock in the laboratory under different variable controlled conditions. In this paper, cyclic fatigue behaviour of intact...With advent of servo-controlled stiff testing machines, it is now possible to conduct tests on a rock in the laboratory under different variable controlled conditions. In this paper, cyclic fatigue behaviour of intact sandstone obtained from the rock burst prone coal mine in the Czech Republic were presented. Tests were conducted on MTS- 816 rock test system in the laboratory on intact rock samples of L/D ratio 2 under cyclic loading frequency of 0.1, 1, 3, 5, 7 and 10 Hz at amplitude of 0.1 mm under displacement control mode until failure of the samples in uni-axial compression. From, the primary results it was observed that at low loading frequency range of 0.1 to 3 Hz, there was degradation of the rock samples in terms of fatigue strength and modulus. While, at higher frequency rose-up in strength and deformation properties were observed. It was observed that the machine behaviour in terms of amplitude at higher loading frequencies might be affecting the results. It seemed that machine behaviour of servo-hydraulic testing system was also dependent on rock type under investigation.展开更多
The preparation of red,green,and blue quantum dot(QD)pixelated arrays with high precision,resolution,and brightness poses a significant challenge on the development of advanced micro-displays for virtual,augmented,and...The preparation of red,green,and blue quantum dot(QD)pixelated arrays with high precision,resolution,and brightness poses a significant challenge on the development of advanced micro-displays for virtual,augmented,and mixed reality applications.Alongside the controlled synthesis of high-performance QDs,a reliable QD patterning technology is crucial in overcoming this challenge.Among the various methods available,photolithography-based patterning technologies show great potentials in producing ultra-fine QD patterns at micron scale.This review article presents the recent advancements in the field of QD patterning using photolithography techniques and explores their applications in micro-display technology.Firstly,we discuss QD patterning through photolithography techniques employing photoresist(PR),which falls into two categories:PRassisted photolithography and photolithography of QDPR.Subsequently,direct photolithography techniques based on photo-induced crosslinking of photosensitive groups and photo-induced ligand cleavage mechanisms are thoroughly reviewed.Meanwhile,we assess the performance of QD arrays fabricated using these photolithography techniques and their integration into QD light emitting diode display devices as well as color conversionbased micro light emitting diode display devices.Lastly,we summarize the most recent developments in this field and outline future prospects.展开更多
The Hengduan Mountains,situated on the southeastern edge of the Qinghai-Tibet Plateau,are the longest and widest north-south-oriented mountain range in China,exerting a significant influence on the ecological and geog...The Hengduan Mountains,situated on the southeastern edge of the Qinghai-Tibet Plateau,are the longest and widest north-south-oriented mountain range in China,exerting a significant influence on the ecological and geographical pattern.Understanding the topographic and geomorphological characteristics of the Hengduan Mountains is fundamental and crucial for research in related fields such as ecology,geography,and sustainability.In this study,Digital Elevation Model(DEM)data were utilized to extract and analyze the topography and geomorphology(TG)pattern.TG maps have been developed to quantitatively classify the TG types in the Hengduan Mountains by combining the five factors of elevation,slope,aspect,relief and landform.The spatial distribution and quantitative characteristics of these factors were mapped and investigated using geographic information systems.The results revealed that:(1)The Hengduan Mountains exhibit an elongated north-south distribution,with an average elevation of approximately 3746 m,an average slope of around 25°,and an average relief of about 266 m.(2)The Hengduan Mountains display significant elevation differences,with an overall high elevation,characterized by a trend of lower elevation in the east and higher elevation in the west,as well as irregular orientations of various aspects.(3)The 19 landform types were identified,the landform types of the Hengduan Mountains are primarily composed of low-relief high-mountains(42.0618%),low-relief mid-mountains(22.4624%),and high-elevation hills(20.5839%).The results of the study can provide data and information support for the ecology,environmental protection and sustainable development of the Hengduan Mountains.展开更多
Objective weather classification methods have been extensively applied to identify dominant ozone-favorable synoptic weather patterns(SWPs),however,the consistency of different classification methods is rarely examine...Objective weather classification methods have been extensively applied to identify dominant ozone-favorable synoptic weather patterns(SWPs),however,the consistency of different classification methods is rarely examined.In this study,we apply two widely-used objective methods,the self-organizing map(SOM)and K-means clustering analysis,to derive ozone-favorable SWPs at four Chinese megacities in 2015-2022.We find that the two algorithms are largely consistent in recognizing dominant ozone-favorable SWPs for four Chinese megacities.In the case of classifying six SWPs,the derived circulation fields are highly similar with a spatial correlation of 0.99 between the two methods,and the difference in themean frequency of each SWP is less than 7%.The six dominant ozone-favorable SWPs in Guangzhou are all characterized by anomaly higher radiation and temperature,lower cloud cover,relative humidity,and wind speed,and stronger subsidence compared to climatology mean.We find that during 2015-2022,the occurrence of ozone-favorable SWPs days increases significantly at a rate of 3.2 days/year,faster than the increases in the ozone exceedance days(3.0 days/year).The interannual variability between the occurrence of ozone-favorable SWPs and ozone exceedance days are generally consistent with a temporal correlation coefficient of 0.6.In particular,the significant increase in ozone-favorable SWPs in 2022,especially the Subtropical High type which typically occurs in September,is consistent with a long-lasting ozone pollution episode in Guangzhou during September 2022.Our results thus reveal that enhanced frequency of ozone-favorable SWPs plays an important role in the observed 2015-2022 ozone increase in Guangzhou.展开更多
基金co-supported by the Enterprise Innovation and Development Joint Program of the National Natural Science Foundation of China(No.U20B2032)Open Project Funding of State Key Laboratory for High Performance Tools(GXNGJSKL-2024-08)+1 种基金Open Foundation of the State Key Laboratory of Intelligent Manufacturing Equipment and Technology(IMETKF2023005)Introduced Innovative Scientific Research Team Project of Zhongshan(the tenth batch)(CXTD2023008)。
文摘Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro-structure has been applied on the micro-grinding tool.A morphology modeling has been established in this study to characterize the surface of microstructured micro-grinding tool,and the grinding performance of micro-structured micro-grinding tool has been analyzed through undeformed chip thickness,abrasive edge width,and effective distance between abrasives.Then deviation analysis,path optimization and parameter optimization of microchannel array precision grinding have been finished to improve processing quality and efficiency,and the deflection angle has the most obvious effects on the rectangular slot depth,micro-structured micro-grinding tool could reduce 10%surface roughness and 20%grinding force compared to original micro-grinding tool.Finally,the microchannel array has been machined with a size deviation of 2μm and surface roughness of 0.2μm.
基金co-supported by the National Key Research and Development Program of China (No. 2022YFB4600500)the National Natural Science Foundation of China (No. 52235006)
文摘High-performance 24CrNiMo steel was fabricated using Laser Powder Bed Fusion (LPBF). Subsequent quenching treatment was applied and the influence of quenching temperatures on micro-structure evolution and properties was systematically characterised and analysed. The micro-structure of the as-built steel consisted of two parts. The first part comprised martensite with twins combined with ω-Fe nano-particles, and the second part consisted of lower bainite in the molten pool, as well as upper bainite, granular bainite and tempered martensite in the heat-affected zone. With the quenching temperatures varying from 800℃ to 950℃, the micro-structure gradually transformed from acicular ferrite + martensite to tempered martensite +θ-Fe3C carbides, and the grain size exhibited noticeable growth. Moreover, quenching treatments could eliminate the anisotropy and inhomogeneity of the micro-structure. The rod-shaped nanosized η-Fe2C and θ-Fe3C precipitates were clearly observed, which were converted from ω-Fe and distributed at multiple angles in the lath. The size and number of nano-precipitates, triggered by the high self-tempering degree of martensite, gradually increased. The relationships among grain size, the twins, dislocation density and nano-precipitation and the dramatically improved performance of quenched samples were analysed using strengthening mechanisms. After quenching at 850℃, the as-built 24CrNiMo steel attained ultra-high mechanical properties including hardness, Ultimate Tensile Strength (UTS), Elongation (El) and impact energy with values of 480.9 HV_(1), 1611.4 MPa, 9.8% and 42.8 J, respectively. Meanwhile, both the wear and thermal fatigue resistance increased by approximately 40%. This study demonstrated that LPBF-fabricated 24CrNiMo steel, with matching good performances, can be achieved using a subsequent one-step quenching process.
文摘BACKGROUND Drug utilization research has an important role in assisting the healthcare administration to know,compute,and refine the prescription whose principal objective is to enable the rational use of drugs.Research in developing nations relating to the cost of treatment is scarce when compared with developed countries.Thus,the drug utilization research studies from developing nations are most needed,and their number has been growing.AIM To evaluate patterns of utilization of antipsychotic drugs and direct medical cost analysis in patients newly diagnosed with schizophrenia.METHODS The present study was observational in type and based on a retrospective cohort to evaluate patterns of utilization of antipsychotic drugs using World Health Organization(WHO)core prescribing indicators and anatomical therapeutic chemical/defined daily dose indicators.We also calculated direct medical costs for a period of 6 months.RESULTS This study has found that atypical antipsychotics are the mainstay of treatment for schizophrenia in every age group and subcategories of schizophrenia.The evaluation based on WHO prescribing indicators showed a low average number of drugs per prescription and low prescribing frequency of antipsychotics from the National List of Essential Medicines 2015 and the WHO Essential Medicines List 2019.The total mean drug cost of our study was 1396 Indian rupees.The total mean cost due to the investigation in our study was 1017.34 Indian rupees.Therefore,the total mean direct medical cost incurred on patients in our study was 4337.28 Indian rupees.CONCLUSION The information from the present study can be used for reviewing and updating treatment policy at the institutional level.
基金Project(50975095)supported by the National Natural Science Foundation of ChinaProject(2012ZM0048)supported by the Fundamental Research Funds for the Central Universities,China
文摘In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and material properties of sample at various depths from the topmost surface were investigated by SEM, TEM, XRD, OM etc. The experimental results show that the gradient nano/micro-structure was introduced into the surface layer of over 100μm in thickness. The remarkable increase in hardness near the topmost surface was mainly attributed to the reduced grain size. The equiaxed nano-sized grains were in random orientation and the most of their boundaries were low-angle grain boundaries （LAGBs）. The coarse grains are refined into the few micro-sized grains by dislocation activities;deformation twinning was found to be the primary form for the formation of submicron grains;the formation of nanostructure was dominated by dislocation activities accompanied with rotation of grains in local region.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11675198,11875097,11975257,61774072,61574026,and 61971090)the National Key Research and Development Program of China(Grant Nos.2016YFB0400600 and2016YFB0400601)+2 种基金the Fundamental Research Funds for the Central Universities,China(Grant No.DUT19LK45)the China Postdoctoral Science Foundation(Grant No.2016M591434)the Science and Technology Plan of Dalian City,China(Grant No.2018J12GX060).
文摘Nowadays,the superior detection performance of semiconductor neutron detectors is a challenging task.In this paper,we deal with a novel GaN micro-structured neutron detector(GaN-MSND)and compare three different methods such as the method of modulating the trench depth,the method of introducing dielectric layer and p-type inversion region to improve the width of depletion region(W).It is observed that the intensity of electric field can be modulated by scaling the trench depth.On the other hand,the electron blocking region is formed in the detector enveloped with a dielectric layer.Furthermore,the introducing of p-type inversion region produces new p/n junction,which not only promotes the further expansion of the depletion region but also reduces the intensity of electric field produced by main junction.It can be realized that all these methods can considerably enhance the working voltage as well as W.Of them,the improvement on W of GaN-MSND with the p-type inversion region is the most significant and the value of W could reach 12.8μm when the carrier concentration of p-type inversion region is 10^17 cm^-3.Consequently,the value of W is observed to improve 200%for the designed GaN-MSND as compared with that without additional design.This work ensures to the researchers and scientific community the fabrication of GaN-MSND having superior detection limit in the field of intense radiation.
文摘In this paper,we report the study of the process of fabricating a multi-layermetal micro-structure using UV-LIGA overlay technology,includingmask fabrication,substrate treatment,and UV-LIGA overlay processes.To solve the process problems in the masking procedure,the swelling problemof the first layer of SU-8 thick photoresist was studied experimentally.The 5μmline-width compensation and closed 20μmand 30μmisolation strips were designed and fabricated around the micro-structure pattern.The pore problemin the Ni micro-electroforming layer was analyzed and the electroforming parameters were improved.The pH value of the electroforming solution should be controlled between 3.8 and 4.4 and the current density should be below 3 A/dm^2.To solve the problems of high inner stress and incomplete development of the micro-cylinder hole array with a diameter of 30μm,the lithography process was optimized.The pre-baking temperature was increased via gradient heating and rose every 5℃ from 65℃ to 85℃ and then remained at 85℃ for 50 min–1 h.In addition,the full contact exposure was used.Finally,a multi-layer metal micro-structure with high precision and good quality of microelectroforming layer was fabricated using UV-LIGA overlay technology.
文摘A low-power CO_2 laser is used to deposit Fe powder and mixture of Fe andcarbon powder on substrates respectively, and the macro and micro-structure of the formed samplesare investigated. It is demonstrated that most grains of these samples are equi-axed. This isderived from the high nucleation velocity in the shallow melt pool besides rapid solidification ofthe liquid-state alloy or metal. Bainitic structure, combination of pearlite and ferrite structureand ferrite structure are seen respectively in the samples involving various amounts of carbon owingto no martensitic transformation in these small samples.
基金Supported by the Programme of Introducing Talents of Discipline to Universities (B07018)
文摘To obtain the form error of micro-structured surfaces robustly and accurately, a form er- ror evaluation method was developed based on the real coded genetic algorithm （RCGA）. The meth- od employed the average squared distance as the matching criterion. The point to surface distance was achieved by use of iterative method and the modeling of RCGA for the surface matching was also presented in detail. Parameter selection for RCGA including the crossover rate and population size was discussed. Evaluation results of series simulated surfaces without form error show that this method can achieve the accuracy of root mean square deviation （ Sq ） less than 1 nm and surface pro- file error （ St ） less than 4 nm. Evaluation of the surfaces with different simulated errors illustrates that the proposed method can also robustly obtain the form error with nano-meter precision. The e- valuation of actual measured surfaces further indicates that the proposed method is capable of pre- cisely evaluating micro-structured surfaces.
基金This work was financially supported by the National Natural Science Foundation of China(No.21706292)Hunan Provincial Science and Technology Plan Project,China(No.2016TP1007)+1 种基金Hunan Provincial Natural Science Foundation of China(No.2020JJ4107)Kai Han acknowledges the support from Innovation-Driven Project of Central South University(No.2020CX037).
文摘Ni-rich layered material is a kind of high-capacity cathode to meet the requirement of electric vehicles.As for the typical LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) material,the particle formation is significant for electrochemical properties of the cathode.In this work,the structure,morphology,and electrochemical performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) secondary particles and single crystals were systematically studied.A lower Ni^(2+)/Ni^(3+)molar ratio of 0.66 and a lower residual alkali content of 0.228wt%were achieved on the surface of the single crystals.In addition,the single crystals showed a discharge capacity of 191.6 mAh/g at 0.2 C(~12 mAh/g lower than that of the secondary particles)and enhanced the electrochemical stability,especially when cycled at 50℃ and in a wider electrochemical window(between 3.0 and 4.4 V vs.Li+/Li).The LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) secondary particles were suitable for applications requiring high specific capacity,whereas single crystals exhibited better stability,indicating that they are more suitable for use in long life requested devices.
基金The authors acknowledge support from the German Research Foundation(DFG:LE 2249/5-1)the Sino-German Center for Research Promotion(GZ1579)+1 种基金Yunnan Fundamental Research Projects(202201AW070014)Jiajia Qiu and Yu Duan appreciate support from the China Scholarship Council(No.201908530218&202206990027).
文摘Adopting a nano-and micro-structuring approach to fully unleashing the genuine potential of electrode active material benefits in-depth understandings and research progress toward higher energy density electrochemical energy stor-age devices at all technology readiness levels.Due to various challenging issues,especially limited stability,nano-and micro-structured(NMS)electrodes undergo fast electrochemical performance degradation.The emerging NMS scaffold design is a pivotal aspect of many electrodes as it endows them with both robustness and electrochemical performance enhancement,even though it only occupies comple-mentary and facilitating components for the main mechanism.However,extensive efforts are urgently needed toward optimizing the stereoscopic geometrical design of NMS scaffolds to minimize the volume ratio and maximize their functionality to fulfill the ever-increasing dependency and desire for energy power source supplies.This review will aim at highlighting these NMS scaffold design strategies,summariz-ing their corresponding strengths and challenges,and thereby outlining the potential solutions to resolve these challenges,design principles,and key perspectives for future research in this field.Therefore,this review will be one of the earliest reviews from this viewpoint.
基金supported by the National Natural Science Foundation of China (Nos. 40372094 and 49972067)
文摘The sub-vertical meso-and micro-structures and fabrics developed in coesite-bearing foliated eclogites in the Taohang （桃行） area, southeastern Shandong （山东）, China. The diagnostic structures and fabrics, including penetrative foliation or mylonitic foliation containing mineral and stretching lineations, as well as sheath-like folds, appear to be the development of anastomosing UHP eciogite-facies shear belt arrays hosting massive eelogites. Textural relationships and mineral assem-blages indicate that the deformation of foliated eclogites developed closely after the formation of the massive eclogite, prior to the development of the granulite/amphibolite-facies symplectites and coronas, occurring over a very wide pressure range of （31-8）×10^2 MPa. It presents the structural records of the tectonometamorphic processes as being responsible for the earliest stages of exhumation of the UHP metamorphic rocks. Extensive regional field observations show that the meso-and micro-structures and fabrics recognized in the foliated eclogites at Taohang are remarkably similar or consistent in the whole Dabie （大别）-Sulu （苏鲁） UHP metamorphic belt. This article, thus, supports the idea that the earliest stages of exhumation of the UHP metamorphic rocks, from mantle depths to the Moho or the mantle-crust boundary layering, may be attributed mainly to a sub-vertical extrusion and ductile flow along the subduction channel, belonging to a syn-collision exhumation at about 235 to 220 Ma.
基金Supported by the National Natural Science Foundation of China(Nos.20671011,20331010,90406002and90406024)the 111 Project(No.B07012)the Key Laboratory of Structural Chemistry Foundation(No.060017).
文摘A novel flower-like hydrated magnesium carbonate hydroxide, Mg5 （CO3 ）4 （OH）2·4H2O, with micro-structure composed of individual thin nano-sheets was synthesized using a facile solution route without the use of template or organic surfactant. Reaction time has an important effect on the final morphology of the product. The micro-structure and morphology of Mg5 （CO3）4 （OH）2·4H2O were characterized by means of X-ray diffractometry （XRD）, fieldemission scanning electron microscopy（FE-SEM）. Brunauer-Emmett-Teller（BET） surface areas of the samples were also measured. The probable formation mechanism of flower-like micro-structure was discussed. It was found that Mg5 （CO3）4（ OH）2·4H2O with flower-like micro-structure was a novel and efficient catalyst for the synthesis of diphenyl carbonate （DPC） by transesterification of dimethyl carbonate （DMC） with phenol.
基金the Special Funds for Major State Basic Research Projects （No.G2000067102） National Natural Science Foundation of China （No.60474027）.
文摘In this article, the convection dominated convection-diffusion problems with the periodic micro-structure are discussed. A two-scale finite element scheme based on the homogenization technique for this kind of problems is provided. The error estimates between the exact solution and the approximation solution, of the homogenized equation or the two-scale finite element scheme are analyzed. It is shown that the scheme provided in this article is convergent for any fixed diffusion coefficient 5, and it may be convergent independent of δ under some conditions. The numerical results demonstrating the theoretical results are presented in this article.
基金the National Natural Science Foundation of China(No.51775154)the ZheJiang Provincial Natural Science Foundation of China(No.LZ15E050004)
文摘A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We employ a diffuse interface model that incorporates the mechanism of surface diffusion. The mechanism of the fabrication is systematically integrated for high reliability of computational analysis. A semi-implicit Fourier spectral scheme is applied for high efficiency and numerical stability. Moreover, the theoretical analysis provides the guidance that is ordered by the fundamental geometrical design parameters to guide different fabrications of SON structures. The performed simulations suggest a substantial potential of the presented model for a reliable design technology of nano/micro-fabrications.
文摘A new standard parametric modeling method of the micro-structure of plain woven composite is proposed. It is based on good analysis of the mechanical property of the yarn, weaving law of plain woven, and other factors. The method implements a woven fabric composite visual engineering modeling process standardization, and it gives five steps to calculate the key micro-structural parameters of the yarn including the cross-section and the trajectory of the central Line. On the basis, the digital model of a plain woven composite has been constructed. The experimental result shows that the forecast for the mechanical property of the model using finite-element simulation analysis is consistent with the actual value. The shape and the structure of the model are also consistent with the solid.
基金performed with financial grant No.105/01/0042 from Grant Agency of the Czech Republic
文摘With advent of servo-controlled stiff testing machines, it is now possible to conduct tests on a rock in the laboratory under different variable controlled conditions. In this paper, cyclic fatigue behaviour of intact sandstone obtained from the rock burst prone coal mine in the Czech Republic were presented. Tests were conducted on MTS- 816 rock test system in the laboratory on intact rock samples of L/D ratio 2 under cyclic loading frequency of 0.1, 1, 3, 5, 7 and 10 Hz at amplitude of 0.1 mm under displacement control mode until failure of the samples in uni-axial compression. From, the primary results it was observed that at low loading frequency range of 0.1 to 3 Hz, there was degradation of the rock samples in terms of fatigue strength and modulus. While, at higher frequency rose-up in strength and deformation properties were observed. It was observed that the machine behaviour in terms of amplitude at higher loading frequencies might be affecting the results. It seemed that machine behaviour of servo-hydraulic testing system was also dependent on rock type under investigation.
基金supported by the National Natural Science Foundation of China(62374142,12175189 and 11904302)External Cooperation Program of Fujian(2022I0004)+1 种基金Fundamental Research Funds for the Central Universities(20720190005 and 20720220085)Major Science and Technology Project of Xiamen in China(3502Z20191015).
文摘The preparation of red,green,and blue quantum dot(QD)pixelated arrays with high precision,resolution,and brightness poses a significant challenge on the development of advanced micro-displays for virtual,augmented,and mixed reality applications.Alongside the controlled synthesis of high-performance QDs,a reliable QD patterning technology is crucial in overcoming this challenge.Among the various methods available,photolithography-based patterning technologies show great potentials in producing ultra-fine QD patterns at micron scale.This review article presents the recent advancements in the field of QD patterning using photolithography techniques and explores their applications in micro-display technology.Firstly,we discuss QD patterning through photolithography techniques employing photoresist(PR),which falls into two categories:PRassisted photolithography and photolithography of QDPR.Subsequently,direct photolithography techniques based on photo-induced crosslinking of photosensitive groups and photo-induced ligand cleavage mechanisms are thoroughly reviewed.Meanwhile,we assess the performance of QD arrays fabricated using these photolithography techniques and their integration into QD light emitting diode display devices as well as color conversionbased micro light emitting diode display devices.Lastly,we summarize the most recent developments in this field and outline future prospects.
基金funded by the Yunnan Provincial Basic Research Joint Special Fund Project(2019FH001(-052))Cangshan Mountain Synthetic Scientific Expeditions Fund.
文摘The Hengduan Mountains,situated on the southeastern edge of the Qinghai-Tibet Plateau,are the longest and widest north-south-oriented mountain range in China,exerting a significant influence on the ecological and geographical pattern.Understanding the topographic and geomorphological characteristics of the Hengduan Mountains is fundamental and crucial for research in related fields such as ecology,geography,and sustainability.In this study,Digital Elevation Model(DEM)data were utilized to extract and analyze the topography and geomorphology(TG)pattern.TG maps have been developed to quantitatively classify the TG types in the Hengduan Mountains by combining the five factors of elevation,slope,aspect,relief and landform.The spatial distribution and quantitative characteristics of these factors were mapped and investigated using geographic information systems.The results revealed that:(1)The Hengduan Mountains exhibit an elongated north-south distribution,with an average elevation of approximately 3746 m,an average slope of around 25°,and an average relief of about 266 m.(2)The Hengduan Mountains display significant elevation differences,with an overall high elevation,characterized by a trend of lower elevation in the east and higher elevation in the west,as well as irregular orientations of various aspects.(3)The 19 landform types were identified,the landform types of the Hengduan Mountains are primarily composed of low-relief high-mountains(42.0618%),low-relief mid-mountains(22.4624%),and high-elevation hills(20.5839%).The results of the study can provide data and information support for the ecology,environmental protection and sustainable development of the Hengduan Mountains.
基金supported by the Guangdong Basic and Applied Basic Research project (No.2020B0301030004)the Key-Area Research and Development Program of Guangdong Province (No.2020B1111360003)+1 种基金the National Natural Science Foundation of China (No.42105103)the Guangdong Basic and Applied Basic Research Foundation (No.2022A1515011554).
文摘Objective weather classification methods have been extensively applied to identify dominant ozone-favorable synoptic weather patterns(SWPs),however,the consistency of different classification methods is rarely examined.In this study,we apply two widely-used objective methods,the self-organizing map(SOM)and K-means clustering analysis,to derive ozone-favorable SWPs at four Chinese megacities in 2015-2022.We find that the two algorithms are largely consistent in recognizing dominant ozone-favorable SWPs for four Chinese megacities.In the case of classifying six SWPs,the derived circulation fields are highly similar with a spatial correlation of 0.99 between the two methods,and the difference in themean frequency of each SWP is less than 7%.The six dominant ozone-favorable SWPs in Guangzhou are all characterized by anomaly higher radiation and temperature,lower cloud cover,relative humidity,and wind speed,and stronger subsidence compared to climatology mean.We find that during 2015-2022,the occurrence of ozone-favorable SWPs days increases significantly at a rate of 3.2 days/year,faster than the increases in the ozone exceedance days(3.0 days/year).The interannual variability between the occurrence of ozone-favorable SWPs and ozone exceedance days are generally consistent with a temporal correlation coefficient of 0.6.In particular,the significant increase in ozone-favorable SWPs in 2022,especially the Subtropical High type which typically occurs in September,is consistent with a long-lasting ozone pollution episode in Guangzhou during September 2022.Our results thus reveal that enhanced frequency of ozone-favorable SWPs plays an important role in the observed 2015-2022 ozone increase in Guangzhou.
