To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmenta...To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmental Lining,the inorganic retarder sodium pyrophosphate(TSPP)and three organic retarders were added to the A component:sodium citrate(SC),sodium tartrate(ST)and glycerol(GLY).The effect law and microscopic mechanism of viscosity,bleeding rate,setting time,gelling time,compressive strength,and stone rate were investigated.The results revealed that the addition of retarders could enhance the stability and setting time of the A component and increase the gelling time,stone rate,and compressive strength of two-component grout.Among them,the performance of the grout with an SC dosage of 0.1% was superior.The bleeding rate of this grout was reduced to 3.5%,the stone rate of the two-component grout was more than 99%,and the early compressive strength and late compressive strength of this grout were increased by approximately 35% and 7%,respectively.The initial and final setting time of the A component with a TSPP dosage of 0.3% was the longest,which was prolonged to 17 and 26 h,respectively.Microscopic analysis revealed that the four retarders hindered the hydration process of cement through complexation and adsorption,and inhibited the hydration of C_(3)S and the crystallisation of CH.Moreover,they reduced the defects caused by the rapid reaction of water glass and CH on the solid phase structure,enabled the microstructure of the stone body to be denser,and subsequently,enhanced the compressive strength.展开更多
Grouting is an essential technique for reinforcing tunnel rock masses following deformation and failure.However,the mechanisms and effectiveness evaluation of grouting in fractured rock masses that have experienced su...Grouting is an essential technique for reinforcing tunnel rock masses following deformation and failure.However,the mechanisms and effectiveness evaluation of grouting in fractured rock masses that have experienced substantial deformation and transition into the residual stage remain insufficiently understood.To elucidate the relationship between grouting effectiveness and pre-cracking strain,grouting and subsequent re-fracturing tests were conducted on sandy mudstone specimens with varying levels of pre-cracking strain.Additionally,a model was developed to determine the optimal grouting timing during the residual stage.The results indicate that the failure mode of specimens in the residual stage exhibits banded and localized distribution patterns.As pre-cracking strain increases,both the maximum fracture aperture and the relative grout injection ratio increase,with the increases becoming more pronounced at higher strain levels.After grouting,the consolidation coefficient and strength enhancement coefficient exhibit a positive correlation with pre-cracking strain,although the rate of increase gradually decreases.Grouting does not alter the initial failure mode of residual-stage fractured specimens but effectively suppresses secondary crack propagation in regions distant from primary fractures.At the microscale,grout bonds within the rock matrix form cavity structures that delay tensile failure and generate an interconnected network,thereby enhancing crack resistance.Based on the evolution of rock damage and the efficiency of grouting materials utilization,a method is proposed to determine the optimal grouting timing for fractured specimens in the residual stage.At the optimal timing,specimens exhibit moderate damage while maintaining high reinforcement efficiency per unit mass of grout.展开更多
Grouting with water–cement mixtures is the most widely used and cost-effective method for managing excess water inflow during tunnel construction.Due to uncertain geological and hydrological conditions,current grouti...Grouting with water–cement mixtures is the most widely used and cost-effective method for managing excess water inflow during tunnel construction.Due to uncertain geological and hydrological conditions,current grouting design relies heavily on the experience of onsite engineers.Recent advances in machine learning offer a promising alternative to traditional design to predict grout volume and improve grouting efficiency.Here,an artificial neural network(ANN)model was developed using the data set from an operation tunnel of Jurong Rock Caverns in Singapore to showcase an efficient and physics-guided training strategy.The ANN model was refined by incorporating the spatial scenarios,including the number of grouting holes in four quadrants of tunneling faces,the sequence of grouting screens along the tunnel axis,and the order of grouting rounds on the tunneling faces.The results indicate that an improved training strategy should encompass the grouting process,from Round 1 with grouting holes uniformly distributed around the tunnel periphery,to Round 2 with grouting holes drilled midway between neighboring first-round holes,and to Round 3 with grouting holes determined by onsite engineers.This model,trained based on the order of grouting rounds,performs better than the other models,highlighting the importance of establishing machine learning models grounded in physical principles.The finding was verified by the data set from another operation tunnel and concluded with a perspective on future grouting research.展开更多
The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of convention...The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of conventional GEPs is inconvenient compared with that of traditional foundation piles.The pre-bored grouted planted geothermal energy pile(PGP GEP)is an innovative technology to simplify the installation process.Most investigations of in-situ experiments for conventional GEPs have focused on summer conditions.An in-situ test for a PGP GEP was conducted to analyze the temperature changes and thermo-mechanical characteristics under winter conditions.The results show that the average temperature of the pile decreased by 5.1℃,and the pile exhibited a general trend of high temperatures at both ends and low temperatures in the middle.In mechanics,strong pile end restraints resulted in smaller observed axial strain and higher axial thermal-induced force in the pile ends than at the middle of the pile.展开更多
In coal mining on a high-pressure Ordovician limestone aquifer,grouting materials should have sufficient mechanical properties,particularly strong interfacial bonding performance to address stress concentration at the...In coal mining on a high-pressure Ordovician limestone aquifer,grouting materials should have sufficient mechanical properties,particularly strong interfacial bonding performance to address stress concentration at the grout-limestone interface induced by rock stress disturbances during mining.In this study,graphene oxide(GO)was integrated into cement-polyacrylate composite grout to improve its interfacial bonding.First,four-point bending tests were conducted,and the Monte Carlo method combined with the simplex search algorithm was employed to determine the variations in shear cohesion and static friction parameters.The results reveal that GO can significantly increase both the tensile and shear cohesion of the grout-limestone interface,but minimally affects the interfacial friction coefficient.Second,nuclear magnetic resonance(NMR)and scanning electron microscopy(SEM)tests were performed.The results indicate that GO nanosheets result in a squamaceous microstructure of the grout consolidation mass,increasing the adhesion of the grout-limestone interface.Moreover,spiny Aft(ettringite)clusters can be induced in limestone fracture surfaces by GO,which could serve as anchors for limestone and grout consolidation mass.展开更多
Quantitative detection of sleeve grouting compactness is a technical challenge in civil engineering testing.This study explores a novel quantitative detection method based on ultrasonic time-frequency dual-domain anal...Quantitative detection of sleeve grouting compactness is a technical challenge in civil engineering testing.This study explores a novel quantitative detection method based on ultrasonic time-frequency dual-domain analysis.It establishes a mapping relationship between sleeve grouting compactness and characteristic parameters.First,this study made samples with gradient defects for two types of grouting sleeves,G18 and G20.These included four cases:2D,4D,6D defects(where D is the diameter of the grouting sleeve),and no-defect.Then,an ultrasonic input/output data acquisition system was established.Three-dimensional sound field distribution data were obtained through an orthogonal detection layout and pulse reflection principles.Finally,a novel quantification detection with a comprehensive defect index(DI)was established by comprehensively considering eight feature parameters,such as time-frequency domain Kurtosis factor(KU),Skewness factor(SK),Formfactor(FF),Crest factor(CF),Impulse factor(IF),Clearance factor(CLF),Wavelet packet energy entropy(WPEE),and Hilbert energy peak(HEP).Construct a DI index by quantifying the difference between defect signals and defect free signals in the time-frequency domain.Experimental results show that,under no-defect conditions,the values of feature parameters are significantly lower than those under defect conditions.Among these,the KU,FF,CF,WPEE and HEP exhibit strong correlations with grout sleeve compactness.The proposed DI index in both types of grout sleeves showed good universality with a linear fit goodness of 0.847–0.962.However,G20 the larger inner diameter and length of the sleeve result in a more complex medium effect during ultrasonic propagation,making its DI index more sensitive to defects than the G18 sleeve.Therefore,the presented method is effective for quantitative detection and analysis of the compactness of grouting sleeves.展开更多
A paste-like self-flowing pipeline transportation backfilling technology with coal gangue as aggregate is proposed to remove the potential damage caused by coal gangue piles. As well, the difficult problems of recover...A paste-like self-flowing pipeline transportation backfilling technology with coal gangue as aggregate is proposed to remove the potential damage caused by coal gangue piles. As well, the difficult problems of recovering high quality safety coal pillars and deep mining of the Suncun Coal Mine （SCM）, Xinwen Coal Group, Shandong are resolved. The physical-chemical properties of coal gangue, optimized proportion of materials, backfilling system and craft in the SCM were studied in the laboratory and then an industrial test was carried out on high quality coal pillars under a town. The results show that finely crushed kaolinized and fresh gangue with granularity less than 5 mm can be used as aggregate with fly ash to replace part of the cement and a composite water reducer as an additive, accounting for 1.0%-1.5% of the total amount of cement and fly ash. The recommended proportion is l（cement）：4（fly ash）： 15（coal gangue）, with a mass fraction of 72%-75%, rheoiogical paste-like properties and a strength of more than 0.7 MPa at 7 d. The sequence of adding cement, fly ash, water reducer and then coal gangue ensures that the suspended state of the slurry, reducing the wear and jam of pipelines. The working face is advancing continuously by the alternating craft of building block walls with coal gangue and backfilling mined-out gobs with paste-like slurry. The recovery rate is as high as 90% with a backfilling cost of 36.9 YuarffL good utilization of coal gangue and no subsidence on the surface. This technology provides a good theoretical basis and application experience for coal mines, cement backfilling with paste-like slurry.展开更多
Based on the pipe transportation of paste-like backfilling system of a certain deep coal mine,its dynamics process was simulated and analyzed.A two-dimensional dynamic model of extraordinary deep and lone pipe was bui...Based on the pipe transportation of paste-like backfilling system of a certain deep coal mine,its dynamics process was simulated and analyzed.A two-dimensional dynamic model of extraordinary deep and lone pipe was built by GAMBIT,on the basis of which the simulation was done by implicit solver of FLUENT 2ddp.The results show that hydraulic loss of pipe transportation is less than the pressure produced by gravity,which means the backfilling material can flow by itself.When the inlet velocity is 3.2 m/s,the maximum velocity of 4.10 m/s is at the elbow and the maximum velocity in the horizontal pipe is 3.91 m/s,which can both meet the stability requirement.The results of the simulation are proved to be reliable by the residual monitor plotting of related parameter,so it can be concluded that the system of pipe transportation is safe.展开更多
To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfil...To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfilling aggregate,binding material and modified material,respectively.An optimized proportion of backfilling materials with a solid mass fraction of 78%and cement:fly ash:jigging sands mass ratio of 1:2:14,was suggested to Jiangan Pyrite Mine,China.The slurry made by optimized proportion produced obvious shear thinning phenomena,and was confirmed as paste-like slurry.To analyze its rheological characteristics,L-type pipeline test and Haake VT550 rotational viscometer test were conducted.Bingham and Casson fluid models were applied to several paste-like slurry samples to simulate flow and stress states;Casson fluid model was proved to have better simulation effect on paste-like slurry with shear thinning phenomena;rheological parameters of backfilling slurry made by suggested proportion were measured.Initial yield stress,average apparent viscosity and limiting viscosity are 55.35 Pa,1.216 Pa-s and 0.48 Pa-s,respectively.Compared with Bingham fluid model,Casson fluid model has a better simulation effect on paste-like slurry with shear thinning phenomena,through calculating the residual standard deviations.展开更多
The experiments, which include the complete stress-strain curves, triaxial compressive loading history and the main factors affecting the compressive strength of the material, were made to research the mechanical prop...The experiments, which include the complete stress-strain curves, triaxial compressive loading history and the main factors affecting the compressive strength of the material, were made to research the mechanical properties of paste-like fill material. The results show that the material still has a relatively high load-bearing capacity after yielding. From the view of the backfill strength, the suitable content of the fine particles in the aggregates is 20%, the curing temperature of backfill slurry is about 20 centigrade degrees or higher. The backfill strength can reach 2.5-3.6 MPa when the binder dosage is 5%-8%. It can meet the needs for mining with backfill.展开更多
Appropriate determination of the mix ratios of cement grouts is of vital importance to the quality of rock grouting and the risk reduction of groundwater inflow.The behavior of grout,often highly temperature dependent...Appropriate determination of the mix ratios of cement grouts is of vital importance to the quality of rock grouting and the risk reduction of groundwater inflow.The behavior of grout,often highly temperature dependent,is likely to be affected by the elevated ground temperature in deep rock masses.This paper aims to experimentally gain insights into the effects of elevated ground temperatures on the properties of cement grout in fresh and hardened states in deep rock grouting.The results revealed that a temperature of 35°C is crucial for changes in the properties of thick cement grout with a water–cement ratio of less than 0.8.When the temperature is up to 35°C,there can be significant improvements in rheological parameters,acceleration of grout setting,and increase in the rheological time dependence of thick cement grout;however,there may also be a slight impact on the initial grout flowability and the nature of shear thinning.The high temperature may still improve the stability of fresh cement grout and also improve the porosity and creep deformation of hardened cement grout considerably.The proposed constitutive model that couples the Burgers model with a fractional derivativebased Abel dashpot in the series can be used to characterize the creep behavior of hardened cement grout appropriately.The paper provides a valuable reference for optimization of mixture design of cement grouts,thus enhancing deep rock grouting quality and improving safety.展开更多
The cement-fly ash composite expansive stable grout was prepared to deal with the problems of poor stability and volume shrinkage of ordinary cement grout,and the effects of fly ash ratio and water-binder ratio on the...The cement-fly ash composite expansive stable grout was prepared to deal with the problems of poor stability and volume shrinkage of ordinary cement grout,and the effects of fly ash ratio and water-binder ratio on the properties of the grout and its consolidation were analyzed.In addition,the mineral composition and microstructural characteristics of grout consolidation with different mixing ratios were investigated.The experimental results indicate that fly ash and the increase of water-binder ratio reduce the strength of the grout consolidation,and increase the fluidity,bleeding rate,and setting time of the composite grout.However,the magnitude of the fly ash-induced strength reduction decreases with time.And the effect of fly ash on the setting time and compressive strength becomes more significant with the water-binder ratio.The later expansion performance of grout consolidation(after 7-42 d)is improved by fly ash.But the expansibility of consolidation with fly ash decreases at the early curing stage,and the reduction amplitude of expansion rate is smaller and the reduction age is shorter with the water-binder ratio increase.Fly ash improves the corrosion resistance performance of grout consolidation,and the corrosion resistance coefficient rises first and then falls with the fly ash ratio.And for 0.6:1 water-binder ratio,the corrosion resistance coefficient of the samples mixed with fly ash are greater than 100%.XRD and SEM show that fly ash inhibited the formation of ettringite in the early stage,which is unfavorable to the expansion of the slurry,and with the increase of age,this effect gradually weakened.展开更多
Grouting has been the most effective approach to mitigate water inrush disasters in underground engineering due to its ability to plug groundwater and enhance rock strength.Nevertheless,there is a lack of potent numer...Grouting has been the most effective approach to mitigate water inrush disasters in underground engineering due to its ability to plug groundwater and enhance rock strength.Nevertheless,there is a lack of potent numerical tools for assessing the grouting effectiveness in water-rich fractured strata.In this study,the hydro-mechanical coupled discontinuous deformation analysis(HM-DDA)is inaugurally extended to simulate the grouting process in a water-rich discrete fracture network(DFN),including the slurry migration,fracture dilation,water plugging in a seepage field,and joint reinforcement after coagulation.To validate the capabilities of the developed method,several numerical examples are conducted incorporating the Newtonian fluid and Bingham slurry.The simulation results closely align with the analytical solutions.Additionally,a set of compression tests is conducted on the fresh and grouted rock specimens to verify the reinforcement method and calibrate the rational properties of reinforced joints.An engineering-scale model based on a real water inrush case of the Yonglian tunnel in a water-rich fractured zone has been established.The model demonstrates the effectiveness of grouting reinforcement in mitigating water inrush disaster.The results indicate that increased grouting pressure greatly affects the regulation of water outflow from the tunnel face and the prevention of rock detachment face after excavation.展开更多
Due to the invisibility and complexity of the underground spaces,monitoring the propagation and filling characteristics of the grouting slurry post the water–sand mixture inrush in metal mines is challenging,which co...Due to the invisibility and complexity of the underground spaces,monitoring the propagation and filling characteristics of the grouting slurry post the water–sand mixture inrush in metal mines is challenging,which complicates engineering treatment.This research investigated the propagation law of cement-sodium silicate slurry under flowing water conditions within the caving mass of a metal mine.First,based on borehole packer test results and borehole TV images,the fractured strata before grouting were classified into four types:cavity,hidden,fissure,and complete.Second,an orthogonal experimental design was employed to evaluate the impact of four key factors—stratigraphic fragmentation,water flow rate,grouting flow rate,and water-cement ratio—on the efficacy of grouting within a caving mass at the site.The results indicate that the factors influencing grouting efficacy are ranked in the following order of importance:stratigraphic fragmentation>water flow rate>water–cement ratio>grouting flow rate.Ultimately,five propagation filling modes—pure slurry,big crack,small crack,small karst pore,and pore penetration—were identified by examining the propagation filling characteristics of slurry in rock samples,incorporating microscopic material structure analysis through scanning electron microscopy and energy spectrum analysis.The findings of this study provide valuable insights into selecting engineering treatment parameters and methodologies,serving as a reference for preventing and controlling water–sand mixture inrush in metal mines,thereby enhancing treatment efficacy and ensuring grouting success.展开更多
The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride so...The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride solutions of specific concentrations with different test ages.Hardened properties of the mixes were assessed in terms of weight loss and compressive strength.X-ray diffraction(XRD)and scanning electron microscopy(SEM)of mixes were performed to analysis the phase evolution and microstructure.The results demonstrated that the introduction of nano-SiO_(2) emulsion significantly decreased the compressive strength loss and calcium hydroxide(CH)crystal content of hydration production,and then enhanced the resistance of cement-based grouting materials to chloride ion penetration.This improvement derives from the filling and pozzolanic effects of nano-SiO_(2) particles,which were incorporated via an emulsion and attributed to a well dispersion in grouting matrix.展开更多
Suction bucket jacket foundations exhibit considerable potential for implementation in deep-sea offshore wind power projects. To address water film formation resulting from negative pressure penetration during constru...Suction bucket jacket foundations exhibit considerable potential for implementation in deep-sea offshore wind power projects. To address water film formation resulting from negative pressure penetration during construction, certain suction bucket jacket foundation projects implement grouting techniques to ensure adequate bearing capacity. This study conducted a large-scale suction bucket foundation grouting model experiment to examine grout flow characteristics and specific phenomena under various grouting pipeline configurations. Comparative analyses of grouting efficiency and quality across different pipeline layouts identified critical influencing factors and their impact on grouting performance. The results demonstrate that the number of grout outlets should be maintained within an optimal range:insufficient outlets enhance the indentation effect and decrease fill efficiency, while excessive outlets necessitate precise spacing for effective distribution. Additionally, grout outlets should be uniformly arranged to reduce segregation and enhance overall grouting quality. This study's findings provide a scientific foundation for optimizing grouting design in suction bucket jacket foundations, with substantial implications for engineering applications.展开更多
Curtain grouting projects are characterized by their large scale and complexity,presenting significant challenges for real-time prediction of grout penetration using traditional methods.This study introduces an intell...Curtain grouting projects are characterized by their large scale and complexity,presenting significant challenges for real-time prediction of grout penetration using traditional methods.This study introduces an intelligent prediction method for grouting in fractured rock masses based on three core principles:integration of multi-source input features,fracture voxel modeling,and shortest path in sequential grouting.Three categories of data(geological structure data,grouting environmental data,and grouting operation data in the concept of a grouting geological model)are integrated and served as multi-source structured data in the intelligent prediction of grouting.A voxelization model quantifies the spatial characteristics of fractures,with voxel size optimized for capturing grouting paths.A shortest path algorithm based on a hierarchical solution is then developed to calculate grout penetration distances in the process of sequential grouting.A complete analysis framework is established,from the voxelization of the fracture network model to precise voxel classification,ultimately achieving an accurate prediction of grout penetration.The method demonstrates excellent performance on the test set,with validation against numerical methods in single-fracture and sequential grouting scenarios confirming its accuracy and prediction efficiency as hundreds of times faster than numerical methods.Application to the Dongzhuang hydraulic project’s grouting test area further validates its effectiveness in multi-hole grouting scenarios.展开更多
Grouting injection is a vital technique for addressing the challenges of high stress and significant deformation in the surrounding rock during deep mining operations,playing a crucial role in promoting green and low-...Grouting injection is a vital technique for addressing the challenges of high stress and significant deformation in the surrounding rock during deep mining operations,playing a crucial role in promoting green and low-carbon extraction methodologies.In this study,grouting reinforcement processes were examined by conducting grouting experiments on a fractured rock with varying negative pressures(0-100 kPa),followed by uniaxial compression testing of the grout-reinforced bodies.This investigation explored the diffusion patterns of grout under negative pressure and established a constitutive model of damage-bearing capacity for bodies reinforced by negative pressure grouting.It further studied the enhancement effect of negative pressure on the load-bearing capacity of the reinforced bodies and analyzed the instability mechanism of damage and failure in these bodies.The results indicated that the diffusion of grout under negative pressure is influenced by four types of forces,which alter the extent of grout diffusion within the fractured rock mass.Introducing a damage constitutive model that serially connects pore and framework elements characterizes the damage and failure behavior of groutreinforced bodies under different negative pressures.As the negative pressure increases,changes in porosity,water-to-cement ratio,and admixture quantity occur in the grout-reinforced specimens,with the strength mean curve showing a trend of first increasing and then decreasing,reaching a threshold at a negative pressure of 60 kPa.With increasing negative pressure,the negative pressure damage variable decreases and then increases,and the stronger the interfacial microelement connections caused by the negative pressure,the greater the bearing capacity,ultimately manifesting in different failure modes.展开更多
The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,h...The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,heightened lateral convergence,and internal force redistribution-may significantly compromise subway operational safety.Grouting remediation has become a widely adopted solution for tunnel deformation control and structural reinforcement.Developing optimized grouting materials is crucial for improving remediation effectiveness,ensuring structural integrity,and maintaining uninterrupted subway operations.This investigation explores the substitution of fine mortar aggregates with 0.1 mm discarded rubber particles at varying concentrations(0%,3%,6%,9%,12%,and 15%).Experimental parameters included three water-cement ratios(0.65,0.70,and 0.75)with constant 4%WPU content.Mechanical properties including compressive strength,flexural strength,and compression-to-bending ratio were evaluated across specified curing periods.Material characterization employed Fourier Transform Infrared Spectroscopy(FTIR)spectroscopy for molecular analysis and Scanning Electron Microscopy(SEM)for microstructural examination.Results indicate optimal toughness at 0.70 water-cement ratio with 6%rubber content,meeting mechanical pumping specifications while maintaining structural performance.展开更多
Grouting is a widely applied technique for reinforcing fractured zones in deep soft rock tunnels.By infiltrating rock fissures,slurry materials enhance structural integrity and improve the overall stability of the sur...Grouting is a widely applied technique for reinforcing fractured zones in deep soft rock tunnels.By infiltrating rock fissures,slurry materials enhance structural integrity and improve the overall stability of the surrounding rock.The performance of grouting is primarily governed by the flow behavior and diffusion extent of the slurry.This review considers recent advances in the theory and methodology of slurry flow and diffusion in fractured rock.It examines commonly used grout materials,including cement-based,chemical,and composite formulations,each offering distinct advantages for specific geological conditions.Themechanisms of reinforcement vary significantly across materials,requiring tailored application strategies.The rheological properties of grouting slurries,particularly cement-based types,have been widely modeled using classical constitutive approaches.However,the influence of time-and space-dependent viscosity evolution on slurry behavior remains underexplored.Experimental studies have provided valuable insights into slurry diffusion,yet further research is needed to capture real-time behavior under multi-scale and multi-physics coupling conditions.Similarly,current numerical simulations are largely limited to twoand three-dimensional models of single-fracture flow.These models often neglect the complexity of fracture networks and geological heterogeneity,highlighting a need for more realistic and integrated simulation frameworks.Future research should focus on:(1)fine-scale modeling of slurry hydration and mechanical reinforcement processes;(2)cross-scale analysis of slurry flow under coupled thermal,hydraulic,andmechanical fields;and(3)development of realtime,three-dimensional dynamic simulation tools to capture the full grouting process.These efforts will strengthen the theoretical foundation and practical effectiveness of grouting in complex underground environments.展开更多
基金Funded by the National Natural Science Foundation of China(No.52378394)the Fundamental Research Funds for the Central Universities(No.B230201037)。
文摘To address the issues of short setting time and high bleeding rate of A component,which easily cause pipe plugging and poor grouting performance when a two-component grout is injected synchronously behind the Segmental Lining,the inorganic retarder sodium pyrophosphate(TSPP)and three organic retarders were added to the A component:sodium citrate(SC),sodium tartrate(ST)and glycerol(GLY).The effect law and microscopic mechanism of viscosity,bleeding rate,setting time,gelling time,compressive strength,and stone rate were investigated.The results revealed that the addition of retarders could enhance the stability and setting time of the A component and increase the gelling time,stone rate,and compressive strength of two-component grout.Among them,the performance of the grout with an SC dosage of 0.1% was superior.The bleeding rate of this grout was reduced to 3.5%,the stone rate of the two-component grout was more than 99%,and the early compressive strength and late compressive strength of this grout were increased by approximately 35% and 7%,respectively.The initial and final setting time of the A component with a TSPP dosage of 0.3% was the longest,which was prolonged to 17 and 26 h,respectively.Microscopic analysis revealed that the four retarders hindered the hydration process of cement through complexation and adsorption,and inhibited the hydration of C_(3)S and the crystallisation of CH.Moreover,they reduced the defects caused by the rapid reaction of water glass and CH on the solid phase structure,enabled the microstructure of the stone body to be denser,and subsequently,enhanced the compressive strength.
基金supported by the National Natural Science Foundation of China(Grant Nos.52274091 and 51974193).
文摘Grouting is an essential technique for reinforcing tunnel rock masses following deformation and failure.However,the mechanisms and effectiveness evaluation of grouting in fractured rock masses that have experienced substantial deformation and transition into the residual stage remain insufficiently understood.To elucidate the relationship between grouting effectiveness and pre-cracking strain,grouting and subsequent re-fracturing tests were conducted on sandy mudstone specimens with varying levels of pre-cracking strain.Additionally,a model was developed to determine the optimal grouting timing during the residual stage.The results indicate that the failure mode of specimens in the residual stage exhibits banded and localized distribution patterns.As pre-cracking strain increases,both the maximum fracture aperture and the relative grout injection ratio increase,with the increases becoming more pronounced at higher strain levels.After grouting,the consolidation coefficient and strength enhancement coefficient exhibit a positive correlation with pre-cracking strain,although the rate of increase gradually decreases.Grouting does not alter the initial failure mode of residual-stage fractured specimens but effectively suppresses secondary crack propagation in regions distant from primary fractures.At the microscale,grout bonds within the rock matrix form cavity structures that delay tensile failure and generate an interconnected network,thereby enhancing crack resistance.Based on the evolution of rock damage and the efficiency of grouting materials utilization,a method is proposed to determine the optimal grouting timing for fractured specimens in the residual stage.At the optimal timing,specimens exhibit moderate damage while maintaining high reinforcement efficiency per unit mass of grout.
基金Ministry of Education-Singapore,Grant/Award Number:RG143/23。
文摘Grouting with water–cement mixtures is the most widely used and cost-effective method for managing excess water inflow during tunnel construction.Due to uncertain geological and hydrological conditions,current grouting design relies heavily on the experience of onsite engineers.Recent advances in machine learning offer a promising alternative to traditional design to predict grout volume and improve grouting efficiency.Here,an artificial neural network(ANN)model was developed using the data set from an operation tunnel of Jurong Rock Caverns in Singapore to showcase an efficient and physics-guided training strategy.The ANN model was refined by incorporating the spatial scenarios,including the number of grouting holes in four quadrants of tunneling faces,the sequence of grouting screens along the tunnel axis,and the order of grouting rounds on the tunneling faces.The results indicate that an improved training strategy should encompass the grouting process,from Round 1 with grouting holes uniformly distributed around the tunnel periphery,to Round 2 with grouting holes drilled midway between neighboring first-round holes,and to Round 3 with grouting holes determined by onsite engineers.This model,trained based on the order of grouting rounds,performs better than the other models,highlighting the importance of establishing machine learning models grounded in physical principles.The finding was verified by the data set from another operation tunnel and concluded with a perspective on future grouting research.
文摘The main purpose of using geothermal energy piles(GEPs)is to enable the exploitation of geothermal energy for meeting the heating/cooling demands of buildings efficiently.However,the installation process of conventional GEPs is inconvenient compared with that of traditional foundation piles.The pre-bored grouted planted geothermal energy pile(PGP GEP)is an innovative technology to simplify the installation process.Most investigations of in-situ experiments for conventional GEPs have focused on summer conditions.An in-situ test for a PGP GEP was conducted to analyze the temperature changes and thermo-mechanical characteristics under winter conditions.The results show that the average temperature of the pile decreased by 5.1℃,and the pile exhibited a general trend of high temperatures at both ends and low temperatures in the middle.In mechanics,strong pile end restraints resulted in smaller observed axial strain and higher axial thermal-induced force in the pile ends than at the middle of the pile.
基金supported by the National Key R&D Program of China(Grant Nos.U25A20810 and 2024YFF0508201)the National Natural Science Foundation of China(Grant No.12302504).
文摘In coal mining on a high-pressure Ordovician limestone aquifer,grouting materials should have sufficient mechanical properties,particularly strong interfacial bonding performance to address stress concentration at the grout-limestone interface induced by rock stress disturbances during mining.In this study,graphene oxide(GO)was integrated into cement-polyacrylate composite grout to improve its interfacial bonding.First,four-point bending tests were conducted,and the Monte Carlo method combined with the simplex search algorithm was employed to determine the variations in shear cohesion and static friction parameters.The results reveal that GO can significantly increase both the tensile and shear cohesion of the grout-limestone interface,but minimally affects the interfacial friction coefficient.Second,nuclear magnetic resonance(NMR)and scanning electron microscopy(SEM)tests were performed.The results indicate that GO nanosheets result in a squamaceous microstructure of the grout consolidation mass,increasing the adhesion of the grout-limestone interface.Moreover,spiny Aft(ettringite)clusters can be induced in limestone fracture surfaces by GO,which could serve as anchors for limestone and grout consolidation mass.
基金supported in part by the National Natural Science Foundation of China Grant 11962006the Natural Science Foundation of Jiangxi Province of China Grant 20232BAB204067.
文摘Quantitative detection of sleeve grouting compactness is a technical challenge in civil engineering testing.This study explores a novel quantitative detection method based on ultrasonic time-frequency dual-domain analysis.It establishes a mapping relationship between sleeve grouting compactness and characteristic parameters.First,this study made samples with gradient defects for two types of grouting sleeves,G18 and G20.These included four cases:2D,4D,6D defects(where D is the diameter of the grouting sleeve),and no-defect.Then,an ultrasonic input/output data acquisition system was established.Three-dimensional sound field distribution data were obtained through an orthogonal detection layout and pulse reflection principles.Finally,a novel quantification detection with a comprehensive defect index(DI)was established by comprehensively considering eight feature parameters,such as time-frequency domain Kurtosis factor(KU),Skewness factor(SK),Formfactor(FF),Crest factor(CF),Impulse factor(IF),Clearance factor(CLF),Wavelet packet energy entropy(WPEE),and Hilbert energy peak(HEP).Construct a DI index by quantifying the difference between defect signals and defect free signals in the time-frequency domain.Experimental results show that,under no-defect conditions,the values of feature parameters are significantly lower than those under defect conditions.Among these,the KU,FF,CF,WPEE and HEP exhibit strong correlations with grout sleeve compactness.The proposed DI index in both types of grout sleeves showed good universality with a linear fit goodness of 0.847–0.962.However,G20 the larger inner diameter and length of the sleeve result in a more complex medium effect during ultrasonic propagation,making its DI index more sensitive to defects than the G18 sleeve.Therefore,the presented method is effective for quantitative detection and analysis of the compactness of grouting sleeves.
基金Projects 2006BAB02A03 supported by the National Key Technology Research and Development ProgramProjects 2006BA02B05 by the 11th Five Year Key Program for Science and Technology Development of China
文摘A paste-like self-flowing pipeline transportation backfilling technology with coal gangue as aggregate is proposed to remove the potential damage caused by coal gangue piles. As well, the difficult problems of recovering high quality safety coal pillars and deep mining of the Suncun Coal Mine （SCM）, Xinwen Coal Group, Shandong are resolved. The physical-chemical properties of coal gangue, optimized proportion of materials, backfilling system and craft in the SCM were studied in the laboratory and then an industrial test was carried out on high quality coal pillars under a town. The results show that finely crushed kaolinized and fresh gangue with granularity less than 5 mm can be used as aggregate with fly ash to replace part of the cement and a composite water reducer as an additive, accounting for 1.0%-1.5% of the total amount of cement and fly ash. The recommended proportion is l（cement）：4（fly ash）： 15（coal gangue）, with a mass fraction of 72%-75%, rheoiogical paste-like properties and a strength of more than 0.7 MPa at 7 d. The sequence of adding cement, fly ash, water reducer and then coal gangue ensures that the suspended state of the slurry, reducing the wear and jam of pipelines. The working face is advancing continuously by the alternating craft of building block walls with coal gangue and backfilling mined-out gobs with paste-like slurry. The recovery rate is as high as 90% with a backfilling cost of 36.9 YuarffL good utilization of coal gangue and no subsidence on the surface. This technology provides a good theoretical basis and application experience for coal mines, cement backfilling with paste-like slurry.
基金Project(2008BAB32B03) supported by the National Science and Technology Pillar Program during the 11th Five-year Plan Period of China
文摘Based on the pipe transportation of paste-like backfilling system of a certain deep coal mine,its dynamics process was simulated and analyzed.A two-dimensional dynamic model of extraordinary deep and lone pipe was built by GAMBIT,on the basis of which the simulation was done by implicit solver of FLUENT 2ddp.The results show that hydraulic loss of pipe transportation is less than the pressure produced by gravity,which means the backfilling material can flow by itself.When the inlet velocity is 3.2 m/s,the maximum velocity of 4.10 m/s is at the elbow and the maximum velocity in the horizontal pipe is 3.91 m/s,which can both meet the stability requirement.The results of the simulation are proved to be reliable by the residual monitor plotting of related parameter,so it can be concluded that the system of pipe transportation is safe.
基金Project(2012BAC09B02)supported by the National Science and Technology Pillar Program during the 12th Five-Year Plan Period,China
文摘To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfilling aggregate,binding material and modified material,respectively.An optimized proportion of backfilling materials with a solid mass fraction of 78%and cement:fly ash:jigging sands mass ratio of 1:2:14,was suggested to Jiangan Pyrite Mine,China.The slurry made by optimized proportion produced obvious shear thinning phenomena,and was confirmed as paste-like slurry.To analyze its rheological characteristics,L-type pipeline test and Haake VT550 rotational viscometer test were conducted.Bingham and Casson fluid models were applied to several paste-like slurry samples to simulate flow and stress states;Casson fluid model was proved to have better simulation effect on paste-like slurry with shear thinning phenomena;rheological parameters of backfilling slurry made by suggested proportion were measured.Initial yield stress,average apparent viscosity and limiting viscosity are 55.35 Pa,1.216 Pa-s and 0.48 Pa-s,respectively.Compared with Bingham fluid model,Casson fluid model has a better simulation effect on paste-like slurry with shear thinning phenomena,through calculating the residual standard deviations.
文摘The experiments, which include the complete stress-strain curves, triaxial compressive loading history and the main factors affecting the compressive strength of the material, were made to research the mechanical properties of paste-like fill material. The results show that the material still has a relatively high load-bearing capacity after yielding. From the view of the backfill strength, the suitable content of the fine particles in the aggregates is 20%, the curing temperature of backfill slurry is about 20 centigrade degrees or higher. The backfill strength can reach 2.5-3.6 MPa when the binder dosage is 5%-8%. It can meet the needs for mining with backfill.
基金The Fundamental Research Funds for the Central Universities,Grant/Award Number:YJ2021148National Natural Science Foundation of China,Grant/Award Number:52374132。
文摘Appropriate determination of the mix ratios of cement grouts is of vital importance to the quality of rock grouting and the risk reduction of groundwater inflow.The behavior of grout,often highly temperature dependent,is likely to be affected by the elevated ground temperature in deep rock masses.This paper aims to experimentally gain insights into the effects of elevated ground temperatures on the properties of cement grout in fresh and hardened states in deep rock grouting.The results revealed that a temperature of 35°C is crucial for changes in the properties of thick cement grout with a water–cement ratio of less than 0.8.When the temperature is up to 35°C,there can be significant improvements in rheological parameters,acceleration of grout setting,and increase in the rheological time dependence of thick cement grout;however,there may also be a slight impact on the initial grout flowability and the nature of shear thinning.The high temperature may still improve the stability of fresh cement grout and also improve the porosity and creep deformation of hardened cement grout considerably.The proposed constitutive model that couples the Burgers model with a fractional derivativebased Abel dashpot in the series can be used to characterize the creep behavior of hardened cement grout appropriately.The paper provides a valuable reference for optimization of mixture design of cement grouts,thus enhancing deep rock grouting quality and improving safety.
基金Funded by the National Natural Science Foundation of China(No.51979153)the Yunnan Key Research and Development Program(No.202103AA080016)。
文摘The cement-fly ash composite expansive stable grout was prepared to deal with the problems of poor stability and volume shrinkage of ordinary cement grout,and the effects of fly ash ratio and water-binder ratio on the properties of the grout and its consolidation were analyzed.In addition,the mineral composition and microstructural characteristics of grout consolidation with different mixing ratios were investigated.The experimental results indicate that fly ash and the increase of water-binder ratio reduce the strength of the grout consolidation,and increase the fluidity,bleeding rate,and setting time of the composite grout.However,the magnitude of the fly ash-induced strength reduction decreases with time.And the effect of fly ash on the setting time and compressive strength becomes more significant with the water-binder ratio.The later expansion performance of grout consolidation(after 7-42 d)is improved by fly ash.But the expansibility of consolidation with fly ash decreases at the early curing stage,and the reduction amplitude of expansion rate is smaller and the reduction age is shorter with the water-binder ratio increase.Fly ash improves the corrosion resistance performance of grout consolidation,and the corrosion resistance coefficient rises first and then falls with the fly ash ratio.And for 0.6:1 water-binder ratio,the corrosion resistance coefficient of the samples mixed with fly ash are greater than 100%.XRD and SEM show that fly ash inhibited the formation of ettringite in the early stage,which is unfavorable to the expansion of the slurry,and with the increase of age,this effect gradually weakened.
基金supported by the China Scholarship Council(CSC,Grant No.202108050072)JSPS KAKENHI(Grant No.JP19KK0121)。
文摘Grouting has been the most effective approach to mitigate water inrush disasters in underground engineering due to its ability to plug groundwater and enhance rock strength.Nevertheless,there is a lack of potent numerical tools for assessing the grouting effectiveness in water-rich fractured strata.In this study,the hydro-mechanical coupled discontinuous deformation analysis(HM-DDA)is inaugurally extended to simulate the grouting process in a water-rich discrete fracture network(DFN),including the slurry migration,fracture dilation,water plugging in a seepage field,and joint reinforcement after coagulation.To validate the capabilities of the developed method,several numerical examples are conducted incorporating the Newtonian fluid and Bingham slurry.The simulation results closely align with the analytical solutions.Additionally,a set of compression tests is conducted on the fresh and grouted rock specimens to verify the reinforcement method and calibrate the rational properties of reinforced joints.An engineering-scale model based on a real water inrush case of the Yonglian tunnel in a water-rich fractured zone has been established.The model demonstrates the effectiveness of grouting reinforcement in mitigating water inrush disaster.The results indicate that increased grouting pressure greatly affects the regulation of water outflow from the tunnel face and the prevention of rock detachment face after excavation.
基金The National Natural Science Foundation of China,Grant/Award Number:42130706。
文摘Due to the invisibility and complexity of the underground spaces,monitoring the propagation and filling characteristics of the grouting slurry post the water–sand mixture inrush in metal mines is challenging,which complicates engineering treatment.This research investigated the propagation law of cement-sodium silicate slurry under flowing water conditions within the caving mass of a metal mine.First,based on borehole packer test results and borehole TV images,the fractured strata before grouting were classified into four types:cavity,hidden,fissure,and complete.Second,an orthogonal experimental design was employed to evaluate the impact of four key factors—stratigraphic fragmentation,water flow rate,grouting flow rate,and water-cement ratio—on the efficacy of grouting within a caving mass at the site.The results indicate that the factors influencing grouting efficacy are ranked in the following order of importance:stratigraphic fragmentation>water flow rate>water–cement ratio>grouting flow rate.Ultimately,five propagation filling modes—pure slurry,big crack,small crack,small karst pore,and pore penetration—were identified by examining the propagation filling characteristics of slurry in rock samples,incorporating microscopic material structure analysis through scanning electron microscopy and energy spectrum analysis.The findings of this study provide valuable insights into selecting engineering treatment parameters and methodologies,serving as a reference for preventing and controlling water–sand mixture inrush in metal mines,thereby enhancing treatment efficacy and ensuring grouting success.
基金Funded by a Science and Technology Project from the Ministry of Housing and Urban-Rural Development of the People’s Republic of China(No.2019-K-047)Yangzhou Government-Yangzhou University Cooperative Platform Project for Science and Technology Innovation(No.YZ2020262)。
文摘The chloride penetration resistance of cement-based grout materials was improved by nano-silica emulsion.Specimens of mixtures containing different nano-silica particles or emulsions were exposed in sodium chloride solutions of specific concentrations with different test ages.Hardened properties of the mixes were assessed in terms of weight loss and compressive strength.X-ray diffraction(XRD)and scanning electron microscopy(SEM)of mixes were performed to analysis the phase evolution and microstructure.The results demonstrated that the introduction of nano-SiO_(2) emulsion significantly decreased the compressive strength loss and calcium hydroxide(CH)crystal content of hydration production,and then enhanced the resistance of cement-based grouting materials to chloride ion penetration.This improvement derives from the filling and pozzolanic effects of nano-SiO_(2) particles,which were incorporated via an emulsion and attributed to a well dispersion in grouting matrix.
文摘Suction bucket jacket foundations exhibit considerable potential for implementation in deep-sea offshore wind power projects. To address water film formation resulting from negative pressure penetration during construction, certain suction bucket jacket foundation projects implement grouting techniques to ensure adequate bearing capacity. This study conducted a large-scale suction bucket foundation grouting model experiment to examine grout flow characteristics and specific phenomena under various grouting pipeline configurations. Comparative analyses of grouting efficiency and quality across different pipeline layouts identified critical influencing factors and their impact on grouting performance. The results demonstrate that the number of grout outlets should be maintained within an optimal range:insufficient outlets enhance the indentation effect and decrease fill efficiency, while excessive outlets necessitate precise spacing for effective distribution. Additionally, grout outlets should be uniformly arranged to reduce segregation and enhance overall grouting quality. This study's findings provide a scientific foundation for optimizing grouting design in suction bucket jacket foundations, with substantial implications for engineering applications.
基金supported by the National Natural Science Foundation of China(Grant No.U23A6018)Science and Technology Program of Hebei(Grant No.E2022202041,2022HBQZYCXY004,242Q9920Z)the project of“Key technologies of seepage control system for large-scale hydraulic projects”was also gratefully appreciated.
文摘Curtain grouting projects are characterized by their large scale and complexity,presenting significant challenges for real-time prediction of grout penetration using traditional methods.This study introduces an intelligent prediction method for grouting in fractured rock masses based on three core principles:integration of multi-source input features,fracture voxel modeling,and shortest path in sequential grouting.Three categories of data(geological structure data,grouting environmental data,and grouting operation data in the concept of a grouting geological model)are integrated and served as multi-source structured data in the intelligent prediction of grouting.A voxelization model quantifies the spatial characteristics of fractures,with voxel size optimized for capturing grouting paths.A shortest path algorithm based on a hierarchical solution is then developed to calculate grout penetration distances in the process of sequential grouting.A complete analysis framework is established,from the voxelization of the fracture network model to precise voxel classification,ultimately achieving an accurate prediction of grout penetration.The method demonstrates excellent performance on the test set,with validation against numerical methods in single-fracture and sequential grouting scenarios confirming its accuracy and prediction efficiency as hundreds of times faster than numerical methods.Application to the Dongzhuang hydraulic project’s grouting test area further validates its effectiveness in multi-hole grouting scenarios.
基金the funding support from the Natural Science Foundation of China(Grant No.52130402)the Anhui Province Graduate Education Quality Engineering Project(Grant No.2023cxcysj088)the China Scholarship Council Grants Program(Grant No.202308340082).
文摘Grouting injection is a vital technique for addressing the challenges of high stress and significant deformation in the surrounding rock during deep mining operations,playing a crucial role in promoting green and low-carbon extraction methodologies.In this study,grouting reinforcement processes were examined by conducting grouting experiments on a fractured rock with varying negative pressures(0-100 kPa),followed by uniaxial compression testing of the grout-reinforced bodies.This investigation explored the diffusion patterns of grout under negative pressure and established a constitutive model of damage-bearing capacity for bodies reinforced by negative pressure grouting.It further studied the enhancement effect of negative pressure on the load-bearing capacity of the reinforced bodies and analyzed the instability mechanism of damage and failure in these bodies.The results indicated that the diffusion of grout under negative pressure is influenced by four types of forces,which alter the extent of grout diffusion within the fractured rock mass.Introducing a damage constitutive model that serially connects pore and framework elements characterizes the damage and failure behavior of groutreinforced bodies under different negative pressures.As the negative pressure increases,changes in porosity,water-to-cement ratio,and admixture quantity occur in the grout-reinforced specimens,with the strength mean curve showing a trend of first increasing and then decreasing,reaching a threshold at a negative pressure of 60 kPa.With increasing negative pressure,the negative pressure damage variable decreases and then increases,and the stronger the interfacial microelement connections caused by the negative pressure,the greater the bearing capacity,ultimately manifesting in different failure modes.
基金supported by the National Natural Science Foundation of China,Grant Nos.42477185,41602308the Zhejiang Provincial Natural Science Foundation of China,Grant No.LY20E080005+2 种基金the Zhejiang Province University Students Science and Technology Innovation Program,Grant No.0201310P28the PostGraduate Course Construction Project of Zhejiang University of Science and Technology,Grant No.2021yjskj05the Zhejiang University of Science and Technology Graduate Research and Innovation Fund,Grant No.2023yjskc10.
文摘The ongoing operation of subway systems makes existing tunnels vulnerable to deformations and structural damage caused by adjacent foundation pit construction.Such deformations-manifesting as horizontal displacement,heightened lateral convergence,and internal force redistribution-may significantly compromise subway operational safety.Grouting remediation has become a widely adopted solution for tunnel deformation control and structural reinforcement.Developing optimized grouting materials is crucial for improving remediation effectiveness,ensuring structural integrity,and maintaining uninterrupted subway operations.This investigation explores the substitution of fine mortar aggregates with 0.1 mm discarded rubber particles at varying concentrations(0%,3%,6%,9%,12%,and 15%).Experimental parameters included three water-cement ratios(0.65,0.70,and 0.75)with constant 4%WPU content.Mechanical properties including compressive strength,flexural strength,and compression-to-bending ratio were evaluated across specified curing periods.Material characterization employed Fourier Transform Infrared Spectroscopy(FTIR)spectroscopy for molecular analysis and Scanning Electron Microscopy(SEM)for microstructural examination.Results indicate optimal toughness at 0.70 water-cement ratio with 6%rubber content,meeting mechanical pumping specifications while maintaining structural performance.
基金funded by the National Natural Science Foundation of China[U22A20234]Hubei Province key research and development project[2023BCB121]Wuhan innovation supporting projects[2023020201010079].
文摘Grouting is a widely applied technique for reinforcing fractured zones in deep soft rock tunnels.By infiltrating rock fissures,slurry materials enhance structural integrity and improve the overall stability of the surrounding rock.The performance of grouting is primarily governed by the flow behavior and diffusion extent of the slurry.This review considers recent advances in the theory and methodology of slurry flow and diffusion in fractured rock.It examines commonly used grout materials,including cement-based,chemical,and composite formulations,each offering distinct advantages for specific geological conditions.Themechanisms of reinforcement vary significantly across materials,requiring tailored application strategies.The rheological properties of grouting slurries,particularly cement-based types,have been widely modeled using classical constitutive approaches.However,the influence of time-and space-dependent viscosity evolution on slurry behavior remains underexplored.Experimental studies have provided valuable insights into slurry diffusion,yet further research is needed to capture real-time behavior under multi-scale and multi-physics coupling conditions.Similarly,current numerical simulations are largely limited to twoand three-dimensional models of single-fracture flow.These models often neglect the complexity of fracture networks and geological heterogeneity,highlighting a need for more realistic and integrated simulation frameworks.Future research should focus on:(1)fine-scale modeling of slurry hydration and mechanical reinforcement processes;(2)cross-scale analysis of slurry flow under coupled thermal,hydraulic,andmechanical fields;and(3)development of realtime,three-dimensional dynamic simulation tools to capture the full grouting process.These efforts will strengthen the theoretical foundation and practical effectiveness of grouting in complex underground environments.
