In the relativistic mean field theory and cooling theories,relativistic correction on neutrino emission from neutron stars in four typical nuclear parameter sets,GM1,GL85,GPS250 and GPS300 is studied.Results show that...In the relativistic mean field theory and cooling theories,relativistic correction on neutrino emission from neutron stars in four typical nuclear parameter sets,GM1,GL85,GPS250 and GPS300 is studied.Results show that relativistic effect makes the neutrino emissivity,neutrino luminosity and cooling rate lower,compared with the nonrelativistic case.And the influence of relativistic effect grows with the mass of the neutron star.GPS300 set leads to the biggest fall in neutrino emissivity,whereas GM1 set leads to the largest disparity in cooling rate caused by relativistic effect.展开更多
A new mothod was presented to find the optimal location and parameter setting of Thyristor Controlled Series Compensator (TCSC) to maxmize the transfer capability.Firstly the sensitivity of the transfer capability wit...A new mothod was presented to find the optimal location and parameter setting of Thyristor Controlled Series Compensator (TCSC) to maxmize the transfer capability.Firstly the sensitivity of the transfer capability with respect was described to the line's reactance was described to find the more sensitive lines for installing TCSC,however,the line which has the most sesitivity value is always not the best line for installing TCSC.For solving this problem,the more sensitive m lines were selected as the alternative line group of installing TCSC,and then modified particle swarm optimization (MPSO) was used to find out the optimal location and the optimal parameter settings of TCSC.Particle swarm optimization (PSO) algorithm can results premature convergence.For solving this problem,population entropy and cellular automata were introduced to it.Simulation results of IEEE 30-bus system proved the effectiveness of the method and its application values.展开更多
For impulse radio ultra-wideband (IR-UWB) ranging systems,effects of the settings of transmitter-related parameters, which include the pulse shape, the bandwidth and the pulse repetition interval (PRI), on ranging acc...For impulse radio ultra-wideband (IR-UWB) ranging systems,effects of the settings of transmitter-related parameters, which include the pulse shape, the bandwidth and the pulse repetition interval (PRI), on ranging accuracy were studied through theoretical analysis and simulations. Both the match-filtering based coherent TOA estimation algorithm and the energy-detection based non-coherent algorithm were used during simulations. Results show that the pulse shape has the least effect on the ranging accuracy. Increasing the pulse bandwidth can improve the ranging performance, but the performance is hardly improved any more when the bandwidth is increased beyond a certain level. PRI should be set long enough to guarantee the accurate ranging, because when PRI is shorter than the maximum excess delay of the channel, the ranging accuracy will be deteriorated by inter-pulse interference.展开更多
To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizi...To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizing parameter settings is proposed. The optimized parameters include the best measurement points of the Region of Interest (ROI) and the levels of pyramid filters. Additionally, to address the issue of updating reference frames in practical applications due to the difficulty in estimating the maximum effective measurement value, a mechanism for dynamically updating reference frames is introduced. Experimental results demonstrate that compared to representative image gradient-based displacement measurement methods, the proposed method exhibits higher measurement accuracy in engineering applications. This provides reliable data support for structural damage identification research based on vibration signals and is expected to broaden the engineering application prospects for structural health monitoring.展开更多
Hypersoft set is an extension of soft set as it further partitions each attribute into its corresponding attribute-valued set.This structure is more flexible and useful as it addresses the limitation of soft set for d...Hypersoft set is an extension of soft set as it further partitions each attribute into its corresponding attribute-valued set.This structure is more flexible and useful as it addresses the limitation of soft set for dealing with the scenarios having disjoint attribute-valued sets corresponding to distinct attributes.The main purpose of this study is to make the existing literature regarding neutrosophic parameterized soft set in line with the need of multi-attribute approximate function.Firstly,we conceptualize the neutrosophic parameterized hypersoft sets under the settings of fuzzy set,intuitionistic fuzzy set and neutrosophic set along with some of their elementary properties and set theoretic operations.Secondly,we propose decision-making-based algorithms with the help of these theories.Moreover,illustrative examples are presented which depict the structural validity for successful application to the problems involving vagueness and uncertainties.Lastly,the generalization of the proposed structure is discussed.展开更多
When describing the mechanical behavior of some engineering materials,such as composites,grains,biological materials and cellular solids,the Cosserat continuum theory has more powerful capabilities compared with the c...When describing the mechanical behavior of some engineering materials,such as composites,grains,biological materials and cellular solids,the Cosserat continuum theory has more powerful capabilities compared with the classical Cauchy elasticity since an additional local rotation of point and its counterpart(couple stress)are considered in the Cosserat elasticity to represent the material microscale effects.In this paper,a parameterized level set topology optimization method is developed based on the Cosserat elasticity for the minimum compliance problem of the Cosserat solids.The influence of material characteristic length and Cosserat shear modulus on the optimized structure is investigated in detail.It can be found that the microstructural constants in the Cosserat elasticity have a significant impact on the optimized topology configurations.In addition,the minimum feature size and the geometric complexity of the optimized structure can be controlled implicitly by adjusting the parameters of the characteristic length and Cosserat shear modulus easily.Furthermore,the optimized structure obtained by the developed Cosserat elasticity based parameterized level set method will degenerate to the result by using the classical Cauchy elasticity based parameterized level set method when the Cosserat shear modulus approaches zero.展开更多
In this paper,we consider solving the topology optimization for steady-state incompressibleNavier-Stokes problems via a new topology optimization method called parameterized level set method,which can maintain a relat...In this paper,we consider solving the topology optimization for steady-state incompressibleNavier-Stokes problems via a new topology optimization method called parameterized level set method,which can maintain a relatively smooth level set function with a local optimality condition.The objective of topology optimization is tond an optimal conguration of theuid and solid materials that minimizes power dissipation under a prescribeduid volume fraction constraint.An articial friction force is added to the Navier-Stokes equations to apply the no-slip boundary condition.Although a great deal of work has been carried out for topology optimization ofuidow in recent years,there are few researches on the topology optimization ofuidow with physical body forces.To simulate theuidow in reality,the constant body force(e.g.,gravity)is considered in this paper.Several 2D numerical examples are presented to discuss the relationships between the proposed method with Reynolds number and initial design,and demonstrate the feasibility and superiority of the proposed method in dealing with unstructuredmesh problems.Three 3D numerical examples demonstrate the proposedmethod is feasible in three-dimensional.展开更多
It is proved that the so-called a set of 12-parameter rectangular plate elements with high accuracy constructed by using double set parameter method and undetermined method are, in fact, the same one; the real shape f...It is proved that the so-called a set of 12-parameter rectangular plate elements with high accuracy constructed by using double set parameter method and undetermined method are, in fact, the same one; the real shape function space is nothing but the Adini＇s element＇s, which has nothing to do with the other high degree terms and leads to a new method for constructing the high accuracy plate elements. This fact has never been seen for other conventional and unconventional, conforming and nonconforming rectangular plate elements, such as Quasi-conforming elements, generalized conforming elements and other double set parameter finite elements. Moreover, such kind of rectangular elements can not be constructed by the conventional finite element methods.展开更多
Medical ultrasound contrast imaging is a powerful modality undergoing successive developments in the last decade to date Lately, pulse inversion has been used in both ultrasound tissue harmonic and contrast imaging. H...Medical ultrasound contrast imaging is a powerful modality undergoing successive developments in the last decade to date Lately, pulse inversion has been used in both ultrasound tissue harmonic and contrast imaging. However, there was a tradeoff between resolution and penetration. Chirp excitations partially solved the tradeoff, but the chirp setting parameters were not optimized. The present work proposes for the first time combining chirp inversion with ultrasound contrast imaging, with the motivation to improve the contrast, by automatically optimizing the setting parameters of chirp excitation, it is thus an optimal command problem. Linear chirps, 5 μm diameter microbubbles and gradient ascent algorithm were simulated to optimize the chirp setting parameters. Simulations exhibited a gain of 5 dB by automatic optimization of chirp inversion relative to pulse inversion. The automatic optimization process was quite fast. Combining chirp inversion with ultrasound contrast imaging led to a maximum backscattered power permitting high contrast outcomes and optimum parameters.展开更多
The digital camouflage spraying of special vehicles carried out by robots can greatly improve the spraying efficiency, spraying quality, and rapid adaptability to personalized patterns. The selection of spray tool and...The digital camouflage spraying of special vehicles carried out by robots can greatly improve the spraying efficiency, spraying quality, and rapid adaptability to personalized patterns. The selection of spray tool and the accuracy of the adopted mathematical spray tool model has a great impact on the effectiveness of spray path planning and spraying quality. Since traditional conical spray tool models are not suitable for spraying rectangular digital camouflage, according to the characteristics of digital camouflage, the coating thickness cumulative distribution model of strip nozzle spray tool for 2 D plane spraying and 3 D surface spraying is derived, and its validity is verified by simulation. Based on the accumulation velocity model of the coating thickness(AVCT) on the curved surface and aiming at spraying path planning within the same surface and different surfaces, a path parameter optimization method based on coating uniformity evaluation of adjacent path overlapping area is proposed. Combined with the vehicle surface model, parameters such as path interval, spray tool angle and spray tool motion velocity can be calculated in real-time to ensure uniform coating. Based on the known local three-dimensional model of vehicle surface and the comprehensive spraying simulation, the validity of the purposed models: the coating thickness on the adjacent path area(CTAPA), the coating thickness on the intersection of two surfaces(CTITS), the coating thickness on the intersection of a plane and a surface(CTIPS), and the optimization method of path parameters are verified. The results show that compared with the traditional spray tool, the strip nozzle can better ensure the uniformity of the coating thickness of digital camouflage spray. Finally, according to a practical spraying experiment, the results prove that the proposed models not only are effective but also meet the practical industrial requirements and are of great practical value.展开更多
Traffic-actuated signal employs relatively complex control logic to regulate traffic flow. Introduction of control variables into the traffic-actuated system contributes to system operational flexibility and complexit...Traffic-actuated signal employs relatively complex control logic to regulate traffic flow. Introduction of control variables into the traffic-actuated system contributes to system operational flexibility and complexity, and also complicates the system with uncertainties. The paper proposes two tentative methods to optimize the actuated signal parameters： basic requirements of controller parameters and analytical model, and macroscopic computer simulation. It is concluded that when the actuated signal operates within the volume/capacity range of 0.4 to 0.6, it will create the most significant benefits; the research suggests that minimum green time in the main street shall be set long enough to meet the required demand, preferably at the 60% of the main street capacity. In order to ensure less control delay in a semi-actuated intersection, relatively small values of vehicle extension （e.g., 2.5 s） and maximum green time are recommended to be assigned to the less important street.展开更多
Set Packing问题起源于分割问题的应用,是在强约束条件对元素进行划分。在复杂性理论中,此问题是一类重要的NP难问题,被广泛应用于调度、代码优化和生物信息学等领域。特别是在参数计算理论产生后。此问题再次成为研究的热点问题。依据...Set Packing问题起源于分割问题的应用,是在强约束条件对元素进行划分。在复杂性理论中,此问题是一类重要的NP难问题,被广泛应用于调度、代码优化和生物信息学等领域。特别是在参数计算理论产生后。此问题再次成为研究的热点问题。依据所研究问题的差异,本文将Set Packing问题分成5类,并给出了具体的定义。在此基础上,分别介绍了求解这5类问题的相关算法,着重分析和比较了参数算法中所运用的各项技术,并提出了该问题算法研究的一些发展方向。展开更多
Aiming to solve the misclassification problems of unsupervised polarimetric Wishart clas- sification algorithm based on Freeman decomposition, an unsupervised Polarimetric Synthetic Aper- ture Radar （SAR） Interferot...Aiming to solve the misclassification problems of unsupervised polarimetric Wishart clas- sification algorithm based on Freeman decomposition, an unsupervised Polarimetric Synthetic Aper- ture Radar （SAR） Interferotnery （PolInSAR） classification algorithm based on optimal coherence set parameters is studied and proposed. This algorithm uses the result of Freeman decomposition to divide the image into three basic categories including surface scattering, volume scattering, and double-bounce Then, the PolInSAR optimal coherence set parameters are used to finely divide each of the three basic categories into 9 categories, and the whole image is divided into 27 categories. Because both the Freeman decomposition result and optimal coherence set parameters indicate specific scattering characteristics, the whole image is merged into 16 categories based on physical meaning. At last, the Wishart cluster is employed to obtain the final classification result. To preserve the purity of scattering characteristics, pixels with similar scattering characteristics are restricted to be classified with other pixels. The final classification results effectively resolve the misclassification problem, not only the buildings can be effectively distinguished from vegetation in urban areas, but also the road is well distinguished from grass. In this paper, the E-SAR PolInSAR data of German Aerospace Center （DLR） are used to verify the effectiveness of the algorithm.展开更多
This paper is concerned with a systematic method of smooth switching linear parameter- varying （LPV） controllers design for a morphing aircraft with a variable wing sweep angle. The morphing aircraft is modeled as a...This paper is concerned with a systematic method of smooth switching linear parameter- varying （LPV） controllers design for a morphing aircraft with a variable wing sweep angle. The morphing aircraft is modeled as an LPV system, whose scheduling parameter is the variation rate of the wing sweep angle. By dividing the scheduling parameter set into subsets with overlaps, output feedback controllers which consider smooth switching are designed and the controllers in over- lapped subsets are interpolated from two adjacent subsets. A switching law without constraint on the average dwell time is obtained which makes the conclusion less conservative. Furthermore, a systematic algorithm is developed to improve the efficiency of the controllers design process. The parameter set is divided into the fewest subsets on the premise that the closed-loop system has a desired performance. Simulation results demonstrate the effectiveness of this approach.展开更多
基金Supported in part by National Natural Science Foundation of China under Grant Nos.11265009,11175077,11271055General Project of Liaoning Provincial Department of Education under Grant No.L2015005
文摘In the relativistic mean field theory and cooling theories,relativistic correction on neutrino emission from neutron stars in four typical nuclear parameter sets,GM1,GL85,GPS250 and GPS300 is studied.Results show that relativistic effect makes the neutrino emissivity,neutrino luminosity and cooling rate lower,compared with the nonrelativistic case.And the influence of relativistic effect grows with the mass of the neutron star.GPS300 set leads to the biggest fall in neutrino emissivity,whereas GM1 set leads to the largest disparity in cooling rate caused by relativistic effect.
基金Sponsored by the Specialized Research Fund for the Doctoral Program of Higher Education(Grant No. 20050213006)
文摘A new mothod was presented to find the optimal location and parameter setting of Thyristor Controlled Series Compensator (TCSC) to maxmize the transfer capability.Firstly the sensitivity of the transfer capability with respect was described to the line's reactance was described to find the more sensitive lines for installing TCSC,however,the line which has the most sesitivity value is always not the best line for installing TCSC.For solving this problem,the more sensitive m lines were selected as the alternative line group of installing TCSC,and then modified particle swarm optimization (MPSO) was used to find out the optimal location and the optimal parameter settings of TCSC.Particle swarm optimization (PSO) algorithm can results premature convergence.For solving this problem,population entropy and cellular automata were introduced to it.Simulation results of IEEE 30-bus system proved the effectiveness of the method and its application values.
基金Sponsored by the National Natural Science Foundation of China (Grant No.60432040)the Natural Science Foundation of Guangdong Privince(Grant No.9451805707003235)
文摘For impulse radio ultra-wideband (IR-UWB) ranging systems,effects of the settings of transmitter-related parameters, which include the pulse shape, the bandwidth and the pulse repetition interval (PRI), on ranging accuracy were studied through theoretical analysis and simulations. Both the match-filtering based coherent TOA estimation algorithm and the energy-detection based non-coherent algorithm were used during simulations. Results show that the pulse shape has the least effect on the ranging accuracy. Increasing the pulse bandwidth can improve the ranging performance, but the performance is hardly improved any more when the bandwidth is increased beyond a certain level. PRI should be set long enough to guarantee the accurate ranging, because when PRI is shorter than the maximum excess delay of the channel, the ranging accuracy will be deteriorated by inter-pulse interference.
文摘To enhance the applicability and measurement accuracy of phase-based optical flow method using complex steerable pyramids in structural displacement measurement engineering applications, an improved method of optimizing parameter settings is proposed. The optimized parameters include the best measurement points of the Region of Interest (ROI) and the levels of pyramid filters. Additionally, to address the issue of updating reference frames in practical applications due to the difficulty in estimating the maximum effective measurement value, a mechanism for dynamically updating reference frames is introduced. Experimental results demonstrate that compared to representative image gradient-based displacement measurement methods, the proposed method exhibits higher measurement accuracy in engineering applications. This provides reliable data support for structural damage identification research based on vibration signals and is expected to broaden the engineering application prospects for structural health monitoring.
文摘Hypersoft set is an extension of soft set as it further partitions each attribute into its corresponding attribute-valued set.This structure is more flexible and useful as it addresses the limitation of soft set for dealing with the scenarios having disjoint attribute-valued sets corresponding to distinct attributes.The main purpose of this study is to make the existing literature regarding neutrosophic parameterized soft set in line with the need of multi-attribute approximate function.Firstly,we conceptualize the neutrosophic parameterized hypersoft sets under the settings of fuzzy set,intuitionistic fuzzy set and neutrosophic set along with some of their elementary properties and set theoretic operations.Secondly,we propose decision-making-based algorithms with the help of these theories.Moreover,illustrative examples are presented which depict the structural validity for successful application to the problems involving vagueness and uncertainties.Lastly,the generalization of the proposed structure is discussed.
基金This work was supported by the National Natural Science Foundation of China(Grants 12072242,11772237,and 11472196)the Hubei Provincial Natural Science Foundation(Grant 2020CFB816)the Fundamental Research Funds for the Central Universities(Grant 2042018kf0016).
文摘When describing the mechanical behavior of some engineering materials,such as composites,grains,biological materials and cellular solids,the Cosserat continuum theory has more powerful capabilities compared with the classical Cauchy elasticity since an additional local rotation of point and its counterpart(couple stress)are considered in the Cosserat elasticity to represent the material microscale effects.In this paper,a parameterized level set topology optimization method is developed based on the Cosserat elasticity for the minimum compliance problem of the Cosserat solids.The influence of material characteristic length and Cosserat shear modulus on the optimized structure is investigated in detail.It can be found that the microstructural constants in the Cosserat elasticity have a significant impact on the optimized topology configurations.In addition,the minimum feature size and the geometric complexity of the optimized structure can be controlled implicitly by adjusting the parameters of the characteristic length and Cosserat shear modulus easily.Furthermore,the optimized structure obtained by the developed Cosserat elasticity based parameterized level set method will degenerate to the result by using the classical Cauchy elasticity based parameterized level set method when the Cosserat shear modulus approaches zero.
基金supported by the National Natural Science Foundation of China (Grant No.12072114)the National Key Research and Development Plan (Grant No.2020YFB1709401)the Guangdong Provincial Key Laboratory of Modern Civil Engineering Technology (2021B1212040003).
文摘In this paper,we consider solving the topology optimization for steady-state incompressibleNavier-Stokes problems via a new topology optimization method called parameterized level set method,which can maintain a relatively smooth level set function with a local optimality condition.The objective of topology optimization is tond an optimal conguration of theuid and solid materials that minimizes power dissipation under a prescribeduid volume fraction constraint.An articial friction force is added to the Navier-Stokes equations to apply the no-slip boundary condition.Although a great deal of work has been carried out for topology optimization ofuidow in recent years,there are few researches on the topology optimization ofuidow with physical body forces.To simulate theuidow in reality,the constant body force(e.g.,gravity)is considered in this paper.Several 2D numerical examples are presented to discuss the relationships between the proposed method with Reynolds number and initial design,and demonstrate the feasibility and superiority of the proposed method in dealing with unstructuredmesh problems.Three 3D numerical examples demonstrate the proposedmethod is feasible in three-dimensional.
文摘It is proved that the so-called a set of 12-parameter rectangular plate elements with high accuracy constructed by using double set parameter method and undetermined method are, in fact, the same one; the real shape function space is nothing but the Adini＇s element＇s, which has nothing to do with the other high degree terms and leads to a new method for constructing the high accuracy plate elements. This fact has never been seen for other conventional and unconventional, conforming and nonconforming rectangular plate elements, such as Quasi-conforming elements, generalized conforming elements and other double set parameter finite elements. Moreover, such kind of rectangular elements can not be constructed by the conventional finite element methods.
文摘Medical ultrasound contrast imaging is a powerful modality undergoing successive developments in the last decade to date Lately, pulse inversion has been used in both ultrasound tissue harmonic and contrast imaging. However, there was a tradeoff between resolution and penetration. Chirp excitations partially solved the tradeoff, but the chirp setting parameters were not optimized. The present work proposes for the first time combining chirp inversion with ultrasound contrast imaging, with the motivation to improve the contrast, by automatically optimizing the setting parameters of chirp excitation, it is thus an optimal command problem. Linear chirps, 5 μm diameter microbubbles and gradient ascent algorithm were simulated to optimize the chirp setting parameters. Simulations exhibited a gain of 5 dB by automatic optimization of chirp inversion relative to pulse inversion. The automatic optimization process was quite fast. Combining chirp inversion with ultrasound contrast imaging led to a maximum backscattered power permitting high contrast outcomes and optimum parameters.
基金supported by Key Research and Development Program of China (No. 2018YFB1306303)。
文摘The digital camouflage spraying of special vehicles carried out by robots can greatly improve the spraying efficiency, spraying quality, and rapid adaptability to personalized patterns. The selection of spray tool and the accuracy of the adopted mathematical spray tool model has a great impact on the effectiveness of spray path planning and spraying quality. Since traditional conical spray tool models are not suitable for spraying rectangular digital camouflage, according to the characteristics of digital camouflage, the coating thickness cumulative distribution model of strip nozzle spray tool for 2 D plane spraying and 3 D surface spraying is derived, and its validity is verified by simulation. Based on the accumulation velocity model of the coating thickness(AVCT) on the curved surface and aiming at spraying path planning within the same surface and different surfaces, a path parameter optimization method based on coating uniformity evaluation of adjacent path overlapping area is proposed. Combined with the vehicle surface model, parameters such as path interval, spray tool angle and spray tool motion velocity can be calculated in real-time to ensure uniform coating. Based on the known local three-dimensional model of vehicle surface and the comprehensive spraying simulation, the validity of the purposed models: the coating thickness on the adjacent path area(CTAPA), the coating thickness on the intersection of two surfaces(CTITS), the coating thickness on the intersection of a plane and a surface(CTIPS), and the optimization method of path parameters are verified. The results show that compared with the traditional spray tool, the strip nozzle can better ensure the uniformity of the coating thickness of digital camouflage spray. Finally, according to a practical spraying experiment, the results prove that the proposed models not only are effective but also meet the practical industrial requirements and are of great practical value.
基金supported by the Fundamental Research Funds for the Central Universities (SWJTU09CX042)National Natural Science Foun-dation of China (NSFC-50978222)
文摘Traffic-actuated signal employs relatively complex control logic to regulate traffic flow. Introduction of control variables into the traffic-actuated system contributes to system operational flexibility and complexity, and also complicates the system with uncertainties. The paper proposes two tentative methods to optimize the actuated signal parameters： basic requirements of controller parameters and analytical model, and macroscopic computer simulation. It is concluded that when the actuated signal operates within the volume/capacity range of 0.4 to 0.6, it will create the most significant benefits; the research suggests that minimum green time in the main street shall be set long enough to meet the required demand, preferably at the 60% of the main street capacity. In order to ensure less control delay in a semi-actuated intersection, relatively small values of vehicle extension （e.g., 2.5 s） and maximum green time are recommended to be assigned to the less important street.
文摘Aiming to solve the misclassification problems of unsupervised polarimetric Wishart clas- sification algorithm based on Freeman decomposition, an unsupervised Polarimetric Synthetic Aper- ture Radar （SAR） Interferotnery （PolInSAR） classification algorithm based on optimal coherence set parameters is studied and proposed. This algorithm uses the result of Freeman decomposition to divide the image into three basic categories including surface scattering, volume scattering, and double-bounce Then, the PolInSAR optimal coherence set parameters are used to finely divide each of the three basic categories into 9 categories, and the whole image is divided into 27 categories. Because both the Freeman decomposition result and optimal coherence set parameters indicate specific scattering characteristics, the whole image is merged into 16 categories based on physical meaning. At last, the Wishart cluster is employed to obtain the final classification result. To preserve the purity of scattering characteristics, pixels with similar scattering characteristics are restricted to be classified with other pixels. The final classification results effectively resolve the misclassification problem, not only the buildings can be effectively distinguished from vegetation in urban areas, but also the road is well distinguished from grass. In this paper, the E-SAR PolInSAR data of German Aerospace Center （DLR） are used to verify the effectiveness of the algorithm.
基金supported by the National Natural Science Foundation of China(Nos.61273083 and 61374012)
文摘This paper is concerned with a systematic method of smooth switching linear parameter- varying （LPV） controllers design for a morphing aircraft with a variable wing sweep angle. The morphing aircraft is modeled as an LPV system, whose scheduling parameter is the variation rate of the wing sweep angle. By dividing the scheduling parameter set into subsets with overlaps, output feedback controllers which consider smooth switching are designed and the controllers in over- lapped subsets are interpolated from two adjacent subsets. A switching law without constraint on the average dwell time is obtained which makes the conclusion less conservative. Furthermore, a systematic algorithm is developed to improve the efficiency of the controllers design process. The parameter set is divided into the fewest subsets on the premise that the closed-loop system has a desired performance. Simulation results demonstrate the effectiveness of this approach.
