To address the challenges of poor surface quality and high energy consumption in marble cutting,this study introduces an auxiliary abrasive jet cutting technology enhanced by the use of polyacrylamide(PAM)as a dragred...To address the challenges of poor surface quality and high energy consumption in marble cutting,this study introduces an auxiliary abrasive jet cutting technology enhanced by the use of polyacrylamide(PAM)as a dragreducing additive.The effects of feed rate(50-300 mm/min),polymer concentration(0-0.5 g/L),and nozzle spacing(4-12 mm)on kerf width and surface roughness are systematically investigated through an orthogonal experimental design.Results reveal that feed rate emerges as themost significant factor(p<0.01),followed by PAM concentration and nozzle spacing.The optimal set of parameters,comprising a 200 mm/min feed rate,0.3 g/L PAM concentration,and 6mmnozzle spacing,achieves the narrowest kerf width(0.867 mm)and the lowest surface roughness(10.220μm).Analysis of the underlying mechanisms demonstrates that PAMenhances the energy efficiency of the jet by suppressing turbulent pulsations and increasing fluid viscoelasticity,thereby minimizing energy loss during the cutting process.展开更多
Nitrogen oxides(NO_(x))and particulate matter(PM)present significant risks to both human health and environmental sustainability.The Integrated Dust Removal and Denitrification Technology(DRDt)offers a more efficient ...Nitrogen oxides(NO_(x))and particulate matter(PM)present significant risks to both human health and environmental sustainability.The Integrated Dust Removal and Denitrification Technology(DRDt)offers a more efficient and cost-effective solution for achieving ultralow industrial flue gas emissions;however,its effectiveness is undermined by low catalyst load rates and poor stability in filter materials.This study addresses these limitations by modifying conventional PTFE filter media(PTFE-Tim)through the incorporation of sodium alginate(SA)and dopamine(DA)as modifiers,resulting in two new filter materials:PTFE-SA-MOF and PTFE-DA-MOF.By optimizing the parameters of an orthogonal experimental design,we identified the ideal preparation conditions for these composite materials.The addition of SA and DA enhanced the bonding between the catalyst(Mn-Cu-MOF)crystal particles and the PTFE fibers through mechanisms such as ion exchange,hydrogen bonding,and adhesion.Consequently,the catalyst loading rate and stability of the DRDt filters were significantly improved.Specifically,the PTFE-SA-MOF and PTFE-DA-MOF filters achieved high catalyst loading rates of 15.97% and 15.86%,these values represent improvements of 2.53 and 2.51 times,while maintaining excellent stability,with mass retention rates of 98.64% and 98.27%,respectively,over the conventional PTFE-Tim filter.展开更多
The serpentine convergent-divergent nozzle represents an optimal configuration for nextgeneration fighter aircraft characterized by low detectability and high thrust-to-weight ratio.In contrast to the serpentine conve...The serpentine convergent-divergent nozzle represents an optimal configuration for nextgeneration fighter aircraft characterized by low detectability and high thrust-to-weight ratio.In contrast to the serpentine convergent nozzle,such configuration offers increased design flexibility with additional parameters,leading to heightened interactions among these parameters.As such,it is crucial to reveal the influence of design parameters on the aerodynamic performance of the serpentine convergent-divergent nozzle and the multifactor interaction,as well as its mechanism.Therefore,the influence,interaction and sensitivity of parameters on the aerodynamic performance of the nozzle were numerically investigated using the orthogonal test method.Additionally,the influence mechanism of the convergence angle,throat aspect ratio,and axial length to inlet diameter on the flow characteristics of the nozzle was investigated in detail.The results show that the convergence angle is identified as the main factor affecting the aerodynamic parameters of the nozzle.As the convergence angle increases,the thrust coefficient,total pressure recovery coefficient and discharge coefficient gradually decrease.The interaction between throat aspect ratio and other parameters is obvious.Different design parameters affect the local loss and the friction loss by affecting the curvature and wetted perimeter area,resulting in different aerodynamic characteristics of serpentine convergent-divergent nozzle.展开更多
Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of w...Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of water-cement ratio （mass fraction of water to cement）, epoxy resin content, and waterborne epoxy curing agent content. By orthogonal range and variance analysis, the orders of three factors to influence the strength, the significance levels of different factors, and the optimized compound ratio scheme of copolymer grouting material mixture at different curing ages were determined. An empirical relationship among the strength of copolymer grouting material, the water-cement ratio, the epoxy resin content, and the waterborne epoxy curing agent content was established by multivariate regression analysis. The results indicate that water-cement ratio is the most principal and significant influencing factor on the strength. Epoxy resin content and waterbome epoxy curing agent content also have a significant influence on the strength. But epoxy resin content has a greater influence on the 7-day and 28-day flexural strength, and waterborne epoxy curing agent content has a greater influence on the 3-day flexural strength and the compressive strength. The copolymer grouting material with water-cement ratio of 0.4, epoxy resin content of 8% （mass fraction） and waterbome epoxy curing agent content of 2% （mass fraction） is the best one for repairing of cement concrete pavement. The flexural strength and the compressive strength have good correlation, and the ratio of compressive strength to flexural strength is between 1.0 and 3.3.展开更多
In order to analyze the influence of configuration parameters on dynamic characteristics of machine tools in the working space, the configuration parameters have been suggested based on the orthogonal experiment metho...In order to analyze the influence of configuration parameters on dynamic characteristics of machine tools in the working space, the configuration parameters have been suggested based on the orthogonal experiment method. Dynamic analysis of a milling machine, which is newly designed for producing turbine blades, has been conducted by utilizing the modal synthesis method. The finite element model is verified and updated by experimental modal analysis （EMA） of the machine tool. The result gained by modal synthesis method is compared with whole-model finite element method （FEM） result as well. According to the orthogonal experiment method, four configuration parameters of machine tool are considered as four factors for dynamic characteristics. The influence of configuration parameters on the first three natural frequencies is obtained by range analysis. It is pointed out that configuration parameter is the most important factor affecting the fundamental frequency of machine tools, and configuration parameter has less effect on lower-order modes of the system than others. The combination of configuration parameters which makes the fundamental frequency reach the maximum value is provided. Through demonstration, the conclusion can be drawn that the influence of configuration parameters on the natural frequencies of machine tools can be analyzed explicitly by the orthogonal experiment method, which offers a new method for estimating the dynamic characteristics of machine tools.展开更多
This paper studies the excavation collapse at the Xianghu subway station on Hangzhou metro line 1.The objective is to present an overview of this case study and discuss the cause of the failure.Through field investiga...This paper studies the excavation collapse at the Xianghu subway station on Hangzhou metro line 1.The objective is to present an overview of this case study and discuss the cause of the failure.Through field investigation and preliminary analysis,the reasons for the excavation collapse were the misuse of the soil parameters,over excavation,incorrect installation of steel struts,invalid monitoring data,and inadequate ground improvement.Finally,a small strain constitutive model was used for further analysis.In order to estimate damage efficiently,the orthogonal array(OA) was introduced for screening the key factor in the numerical experiments.Six estimated indexes including deformations and internal forces of the excavation were taken,and the effectiveness of four factors which may cause the collapse was evaluated.Through numerical experiments and interaction analysis,it is found that the deformation and internal force can be well controlled by jet grouting of the subsoil under the final cutting surface,but increasing the improvement ratio of the jet grouting cannot help optimize the excavation behavior efficiently,and without jet grouting and the fourth level struts,the deformation and internal force of the excavation in this case will far surpass the allowable value.展开更多
Sodium silicate modification can improve the overall performance of wood.The modification process has a great influence on the properties of modified wood.In this study,a new method was introduced to analyze the wood ...Sodium silicate modification can improve the overall performance of wood.The modification process has a great influence on the properties of modified wood.In this study,a new method was introduced to analyze the wood modification process,and the properties of modified wood were studied.Poplar wood was modified with sodium silicate by vacuum-pressure impregnation.After screening using single-factor experiments,an orthogonal experiment was carried out with solution concentration,impregnation time,impregnation pressure,and the cycle times as experimental factors.The modified poplar with the best properties was selected by fuzzy mathematics and characterized by SEM,FT-IR,XRD and TG.The results showed that some lignin and hemicellulose were removed from the wood due to the alkaline action of sodium silicate,and the orderly crystal area of poplar became disorderly,resulting in the reduction of crystallinity of the modified poplar wood.FT-IR analysis showed that sodium silicate was hydrolyzed to form polysilicic acid in wood,and structural analysis revealed the formation of Si-O-Si and Si-O-C,indicating that sodium silicate reacted with fibers on the wood cell wall.TG-DTG curves showed that the final residual mass of modified poplar wood increased from 25%to 67%,and the temperature of the maximum loss rate decreased from 343℃ to 276℃.The heat release and smoke release of modified poplar wood decreased obviously.This kind of material with high strength and fire resistance can be used in the outdoor building and indoor furniture.展开更多
In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of w...In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of warm compacted samples was studied. According to the orthogonal test method, the authors systematically study the influence of the different compaction pressure, condition of lubrication and compaction temperature on the green density of the sample in the warm compaction process, and put forward the optimal process parameter of warm compaction experiment. It is found that, a high compaction pressure （≥700 MPa）, die wall lubrication combined with a small amount of internal lubricants, and fitting compaction temperature by different condition of lubrication, are the optimal parameters in warm compaction process.展开更多
The transfer function of the optical splitting system of the acousto-optic tunable filter （AOTF） is deduced to be a reference to optical design. The characteristic matrix （ transfer function） of AOTF is used to de...The transfer function of the optical splitting system of the acousto-optic tunable filter （AOTF） is deduced to be a reference to optical design. The characteristic matrix （ transfer function） of AOTF is used to describe quantitatively the characters of polarization elements in the orthogonal polarizing system. According to the characteristic matrix, the included angle of polarizer＇s transmission direction and polarization analyzer＇s transmission direction should be 90°. As a result the signal to noise ratio increased about 20 times though the light intensity was reduced to 54.3%,because both the transmittances of polarizer and polarization analyzer are 0. 74, which is an intrinsic character. The orthogonal polarizing method is an effective method to get rid of the influence of zero order light and improve the spectrum resolution and signal-to-noise ratio.展开更多
In this paper, we reexamine the method of successive approximation presented by Prof. Chien Wei-zangfor solving the problem of large deflection of a circular plate, and find that the method could be regarded as the me...In this paper, we reexamine the method of successive approximation presented by Prof. Chien Wei-zangfor solving the problem of large deflection of a circular plate, and find that the method could be regarded as the method of strained parameters in the singular perturbation theory. In terms of the parameter representing the ratio of the center deflection to the thickness of the plate, we make the asymptotic expansions of the deflection, membrane stress and the parameter of load as in Ref. [1], and then give the orthogonality conditions (i.e. the solvability conditions) for the resulting equations, by which the stiffness characteristics of the plate could be determined. It is pointed out that with the solutions for the small deflection problem of the circular plate and the orthogonality conditions, we can derive the third order approximate relations between the parameter of load and the center deflection and the first-term approximation of membrane stresses at the center and edge of the plate without solving the differential equations. For some special cases (i.e. under uniform load, under compound toad, with different boundary conditiors), we deduce the specific expressions and obtain the results in agreement with the previous ones given by Chien Wei-zang, Yeh kai-yuan and Hwang Chien in Refs. [1 - 4J.展开更多
In this paper an orthogonal function method is presented based on the idea to suppose perioche sohuion with the method of harmonie balance The displaeement is expressed in the form of trigonometric fumctions a group o...In this paper an orthogonal function method is presented based on the idea to suppose perioche sohuion with the method of harmonie balance The displaeement is expressed in the form of trigonometric fumctions a group of simplified digenequationsare obtained by the use of orthogonarity of trigonometric fumetions and linear mondes The method overcomes the diffieulty of a drifi term existing in systems with quadratic nonlinearities .The ealeulation examples show that the method has thd advantages of high caleulation preeision high convergenee speed and littld ealeulation work展开更多
Finite element method (FEM) is an efficient numerical tool for the solution of partial differential equations (PDEs). It is one of the most general methods when compared to other numerical techniques. PDEs posed in a ...Finite element method (FEM) is an efficient numerical tool for the solution of partial differential equations (PDEs). It is one of the most general methods when compared to other numerical techniques. PDEs posed in a variational form over a given space, say a Hilbert space, are better numerically handled with the FEM. The FEM algorithm is used in various applications which includes fluid flow, heat transfer, acoustics, structural mechanics and dynamics, electric and magnetic field, etc. Thus, in this paper, the Finite Element Orthogonal Collocation Approach (FEOCA) is established for the approximate solution of Time Fractional Telegraph Equation (TFTE) with Mamadu-Njoseh polynomials as grid points corresponding to new basis functions constructed in the finite element space. The FEOCA is an elegant mixture of the Finite Element Method (FEM) and the Orthogonal Collocation Method (OCM). Two numerical examples are experimented on to verify the accuracy and rate of convergence of the method as compared with the theoretical results, and other methods in literature.展开更多
Studies show that the photovoltaic-thermal(PVT)heat pump soil cross-seasonal energy storage system can effectively harness solar energy to supply heating,electricity,and cooling for buildings.The present study investi...Studies show that the photovoltaic-thermal(PVT)heat pump soil cross-seasonal energy storage system can effectively harness solar energy to supply heating,electricity,and cooling for buildings.The present study investigates a real-world application of this system in Dalian,China,outlining its design framework and optimizing key parameters using orthogonal methods.The factors examined include the area,slope angle,and azimuth angle of the PVT collectors,the flow rate through the PVT collectors,and the depth,spacing,count,and flow rate of the borehole.Through variance analysis,the influence of these parameters is evaluated on heat pump efficiency,soil temperature dynamics,and the system’s investment payback period.Findings indicate that borehole depth and PVT area are the dominant factors affecting the heating efficiency of the heat pump,contributing 66.86%and 16.25%,respectively.In the cooling efficiency of the heat pump,the most significant factors include borehole spacing(31.30%),borehole depth(26.36%),PVT area(16.98%),and borehole flow rate(16.67%).The investment payback period is primarily influenced by borehole depth(41.25%)and borehole quantity(25.24%),with PVT area and borehole spacing contributing 15.34%and 15.18%,respectively.Variations in soil temperature are largely governed by PVT area(40.85%)and borehole spacing(32.75%),followed by PVT slope angle(11.41%)and borehole depth(10.31%).The results of this research provide valuable insights for optimizing the design and implementation of PVT heat pump soil cross-seasonal energy storage systems scientifically and efficiently.展开更多
The construction of the cables is a key step for erecting suspen-dome structures. In practical engineering, it is difficult to ensure that the designed pre-stresses of cables have been exactly introduced into the stru...The construction of the cables is a key step for erecting suspen-dome structures. In practical engineering, it is difficult to ensure that the designed pre-stresses of cables have been exactly introduced into the structures in the site; so it is necessary to evaluate the influence of the variation of the pre-stresses on the structural behavior. In the present work, an orthogonal design method was employed to investigate the pre-stressed cables' sensitivity to the suspen-dome system. The investigation was concentrated on a Kiewitt suspen-dome. Parametric studies were carried out to study the sensitivity of the structure's static behavior, dynamic behavior, and buckling loads when the pre-stresses in the cables varied. The investigation indicated that suspen-dome structures are sensitive to the pre-stresses in all cables; and that the sensitivity depended on the location of the cables and the kind of structural behavior. Useful suggestions are given at the end of the paper.展开更多
A new method named orthogonal two-way link-shift here has been proposed.Based on the method and a standard involute gear hob, a specific gear tooth profile (including anarbitrary gear tooth profile and a modified invo...A new method named orthogonal two-way link-shift here has been proposed.Based on the method and a standard involute gear hob, a specific gear tooth profile (including anarbitrary gear tooth profile and a modified involute gear tooth profile) can be generated on aCNC(computer numerical control) bobbing machine. Computer simulation has been carried out, and theresults prove that the method is right and practicable. So, the fabrication costs can be greatlydecreased than before. The new method has momentous significance to realize gear's optimizedmodification under different work conditions.展开更多
a new strategy combining an expert system and improved genetic algorithms is presented for tuning proportional-integral-derivative （PID） parameters for petrochemical processes. This retains the advantages of genetic...a new strategy combining an expert system and improved genetic algorithms is presented for tuning proportional-integral-derivative （PID） parameters for petrochemical processes. This retains the advantages of genetic algorithms, namely rapid convergence and attainment of the global optimum. Utilization of an orthogonal experiment method solves the determination of the genetic factors. Combination with an expert system can make best use of the actual experience of the plant operators. Simulation results of typical process systems examples show a good control performance and robustness.展开更多
As a typical laser additive manufacturing technology,laser powder bed fusion(LPBF)has achieved demonstration applications in aerospace,biomedical and other fields.However,how to select process parameters quickly and r...As a typical laser additive manufacturing technology,laser powder bed fusion(LPBF)has achieved demonstration applications in aerospace,biomedical and other fields.However,how to select process parameters quickly and reasonably is still themain concern of LPBF production.In order to quantitatively analyze the influence of different process parameters(laser power,scanning speed,hatch space and layer thickness)on the LPBF process,the multilayer and multi-path forming process of LPBF was predicted based on the open-source discrete element method framework Yade and the open-source finite volume method framework OpenFOAM.Based on the design of experiments method,a four-factor three-level orthogonal test scheme was designed,and the porosity and surface roughness data of each calculation scheme were extracted.By analyzing the orthogonal test data,it was found that as the laser power increased,the porosity decreased,and as the scanning speed,hatch space,and layer thickness increased,the porosity increased.In addition,the influence of laser power and scanning speed on surface roughness showed a trend of decreasing first and then increasing,while the influence of scanning distance and layer thickness on surface roughness showed amonotonous increasing trend.The order of the influence of each process parameter on porosity was:scanning speed>laying thickness>laser power>hatch space,and the order of the influence of each process parameter on surface roughness was:hatch space>layer thickness>laser power>scanning speed.So the porosity of the part is most sensitive to scanning speed,and the surface roughness is the most sensitive to hatch space.The above conclusions are expected to provide process control basis for actual LPBF production of the 316L stainless steel alloy.展开更多
A modified Gurson-Tvergaard-Needleman(GTN)model that accounts for the mixed(isotropic and kinematic)hardening of cast steel GS-20Mn5V was developed and implemented in the finite dement program ABAQUS/Standard via a us...A modified Gurson-Tvergaard-Needleman(GTN)model that accounts for the mixed(isotropic and kinematic)hardening of cast steel GS-20Mn5V was developed and implemented in the finite dement program ABAQUS/Standard via a user-defined material subroutine UMAT.This model couples the stress state and damage evolution(pore volume fraction increase)by a classic method that assumes that the total void volume fraction is divided into a nucleation and a growth part.A parametric study was conducted to assess the effect of modified GTN model parameters on mechanical properties such as the nucleation,growth and coalescence of voids and to obtain the optimal parameter combination by the orthogonal test method.The predicted load-displacement curves of notched specimens with the optimal parameters are favorably compared to the experimental curves.Therefore,the modified GTN model can be used to predict the damage evaluation and fracture behavior of GS-20Mn5V.展开更多
In this paper, we extend the applications of proper orthogonal decomposition （POD） method, i.e., apply POD method to a mixed finite element （MFE） formulation naturally satisfied Brezz-Babu^ka for parabolic equatio...In this paper, we extend the applications of proper orthogonal decomposition （POD） method, i.e., apply POD method to a mixed finite element （MFE） formulation naturally satisfied Brezz-Babu^ka for parabolic equations, establish a reduced-order MFE formulation with lower dimensions and sufficiently high accuracy, and provide the error estimates between the reduced-order POD MFE solutions and the classical MFE solutions and the implementation of algorithm for solving reduced-order MFE formulation. Some numerical examples illustrate the fact that the results of numerical computation are consis- tent with theoretical conclusions. Moreover, it is shown that the new reduced-order MFE formulation based on POD method is feasible and efficient for solving MFE formulation for parabolic equations.展开更多
The objective of this paper is to optimize the parameters of pellet drying and preheating process in grate.A mathematical model of drying and preheating is developed,and is verified by the experiments.Further,the oper...The objective of this paper is to optimize the parameters of pellet drying and preheating process in grate.A mathematical model of drying and preheating is developed,and is verified by the experiments.Further,the operating parameters of wind temperature,wind speed,grate speed and bed depth etc.are investigated through the orthogonal method using the simulation results.And a relationship of drying,preheating effects and operating parameters is achieved.The results show that the optimization effect can be achieved in the given range when air velocity is about 3.0 m/s and temperature is about 300,500,800,and 1 100 in the updraft drying zone,downdraft drying zone,preheating Ⅰ zone,and preheating Ⅱ zone respectively.The work is help for saving energy and reducing emissions in pellet induration.展开更多
基金supported by the National Natural Science Foundation of China(grant number:52006061)the Key R&D Program of Hunan Province(grant number:2024AQ2001)+2 种基金Scientific Research Program of Hunan Provincial Department of Education(grant number:22B0840)Natural Science Foundation of Hunan Province(grant number:2023JJ50483)Hunan University of Humanities,Science and Technology Graduate Student Research and Innovation Program(ZSCX2024Y06,ZSCX2024Y01).
文摘To address the challenges of poor surface quality and high energy consumption in marble cutting,this study introduces an auxiliary abrasive jet cutting technology enhanced by the use of polyacrylamide(PAM)as a dragreducing additive.The effects of feed rate(50-300 mm/min),polymer concentration(0-0.5 g/L),and nozzle spacing(4-12 mm)on kerf width and surface roughness are systematically investigated through an orthogonal experimental design.Results reveal that feed rate emerges as themost significant factor(p<0.01),followed by PAM concentration and nozzle spacing.The optimal set of parameters,comprising a 200 mm/min feed rate,0.3 g/L PAM concentration,and 6mmnozzle spacing,achieves the narrowest kerf width(0.867 mm)and the lowest surface roughness(10.220μm).Analysis of the underlying mechanisms demonstrates that PAMenhances the energy efficiency of the jet by suppressing turbulent pulsations and increasing fluid viscoelasticity,thereby minimizing energy loss during the cutting process.
基金financially supported by Natural Science Foundation of Anhui Provincial Department of Education(2022AH050337)State Key Laboratory of Safety and Health for Metal Mines(2022-JSKSSYS-04)the Project of National Key Research and Development Program(2022YFC3901405).
文摘Nitrogen oxides(NO_(x))and particulate matter(PM)present significant risks to both human health and environmental sustainability.The Integrated Dust Removal and Denitrification Technology(DRDt)offers a more efficient and cost-effective solution for achieving ultralow industrial flue gas emissions;however,its effectiveness is undermined by low catalyst load rates and poor stability in filter materials.This study addresses these limitations by modifying conventional PTFE filter media(PTFE-Tim)through the incorporation of sodium alginate(SA)and dopamine(DA)as modifiers,resulting in two new filter materials:PTFE-SA-MOF and PTFE-DA-MOF.By optimizing the parameters of an orthogonal experimental design,we identified the ideal preparation conditions for these composite materials.The addition of SA and DA enhanced the bonding between the catalyst(Mn-Cu-MOF)crystal particles and the PTFE fibers through mechanisms such as ion exchange,hydrogen bonding,and adhesion.Consequently,the catalyst loading rate and stability of the DRDt filters were significantly improved.Specifically,the PTFE-SA-MOF and PTFE-DA-MOF filters achieved high catalyst loading rates of 15.97% and 15.86%,these values represent improvements of 2.53 and 2.51 times,while maintaining excellent stability,with mass retention rates of 98.64% and 98.27%,respectively,over the conventional PTFE-Tim filter.
基金supported by the National Science and Technology Major Project of China(No.J2019-Ⅲ-0009-0053)。
文摘The serpentine convergent-divergent nozzle represents an optimal configuration for nextgeneration fighter aircraft characterized by low detectability and high thrust-to-weight ratio.In contrast to the serpentine convergent nozzle,such configuration offers increased design flexibility with additional parameters,leading to heightened interactions among these parameters.As such,it is crucial to reveal the influence of design parameters on the aerodynamic performance of the serpentine convergent-divergent nozzle and the multifactor interaction,as well as its mechanism.Therefore,the influence,interaction and sensitivity of parameters on the aerodynamic performance of the nozzle were numerically investigated using the orthogonal test method.Additionally,the influence mechanism of the convergence angle,throat aspect ratio,and axial length to inlet diameter on the flow characteristics of the nozzle was investigated in detail.The results show that the convergence angle is identified as the main factor affecting the aerodynamic parameters of the nozzle.As the convergence angle increases,the thrust coefficient,total pressure recovery coefficient and discharge coefficient gradually decrease.The interaction between throat aspect ratio and other parameters is obvious.Different design parameters affect the local loss and the friction loss by affecting the curvature and wetted perimeter area,resulting in different aerodynamic characteristics of serpentine convergent-divergent nozzle.
基金Projects(40728003, 40772180, 40802064) supported by the National Natural Science Foundation of ChinaProject (07JJ4012) supported by the Hunan Provincial Natural Science Foundation of China+1 种基金project (20080430680) supported by China Postdoctoral Science FoundationProject(B308) supported by Shanghai Leading Academic Discipline Project
文摘Using the orthogonal experimental design method involving three factors and three levels, the flexural strength and the compressive strength of copolymer grouting material were studied with different compositions of water-cement ratio （mass fraction of water to cement）, epoxy resin content, and waterborne epoxy curing agent content. By orthogonal range and variance analysis, the orders of three factors to influence the strength, the significance levels of different factors, and the optimized compound ratio scheme of copolymer grouting material mixture at different curing ages were determined. An empirical relationship among the strength of copolymer grouting material, the water-cement ratio, the epoxy resin content, and the waterborne epoxy curing agent content was established by multivariate regression analysis. The results indicate that water-cement ratio is the most principal and significant influencing factor on the strength. Epoxy resin content and waterbome epoxy curing agent content also have a significant influence on the strength. But epoxy resin content has a greater influence on the 7-day and 28-day flexural strength, and waterborne epoxy curing agent content has a greater influence on the 3-day flexural strength and the compressive strength. The copolymer grouting material with water-cement ratio of 0.4, epoxy resin content of 8% （mass fraction） and waterbome epoxy curing agent content of 2% （mass fraction） is the best one for repairing of cement concrete pavement. The flexural strength and the compressive strength have good correlation, and the ratio of compressive strength to flexural strength is between 1.0 and 3.3.
基金Important National Science & Technology Specific Projects (2009ZX04001-073)National Natural Science Foundation of China (51105025)
文摘In order to analyze the influence of configuration parameters on dynamic characteristics of machine tools in the working space, the configuration parameters have been suggested based on the orthogonal experiment method. Dynamic analysis of a milling machine, which is newly designed for producing turbine blades, has been conducted by utilizing the modal synthesis method. The finite element model is verified and updated by experimental modal analysis （EMA） of the machine tool. The result gained by modal synthesis method is compared with whole-model finite element method （FEM） result as well. According to the orthogonal experiment method, four configuration parameters of machine tool are considered as four factors for dynamic characteristics. The influence of configuration parameters on the first three natural frequencies is obtained by range analysis. It is pointed out that configuration parameter is the most important factor affecting the fundamental frequency of machine tools, and configuration parameter has less effect on lower-order modes of the system than others. The combination of configuration parameters which makes the fundamental frequency reach the maximum value is provided. Through demonstration, the conclusion can be drawn that the influence of configuration parameters on the natural frequencies of machine tools can be analyzed explicitly by the orthogonal experiment method, which offers a new method for estimating the dynamic characteristics of machine tools.
基金Project (No. 51078377) supported by the National Natural Science Foundation of China
文摘This paper studies the excavation collapse at the Xianghu subway station on Hangzhou metro line 1.The objective is to present an overview of this case study and discuss the cause of the failure.Through field investigation and preliminary analysis,the reasons for the excavation collapse were the misuse of the soil parameters,over excavation,incorrect installation of steel struts,invalid monitoring data,and inadequate ground improvement.Finally,a small strain constitutive model was used for further analysis.In order to estimate damage efficiently,the orthogonal array(OA) was introduced for screening the key factor in the numerical experiments.Six estimated indexes including deformations and internal forces of the excavation were taken,and the effectiveness of four factors which may cause the collapse was evaluated.Through numerical experiments and interaction analysis,it is found that the deformation and internal force can be well controlled by jet grouting of the subsoil under the final cutting surface,but increasing the improvement ratio of the jet grouting cannot help optimize the excavation behavior efficiently,and without jet grouting and the fourth level struts,the deformation and internal force of the excavation in this case will far surpass the allowable value.
基金This work was financially supported by National Natural Science Foundation of China(32201485)Natural Science Foundation of Hunan Province,China(2022JJ40863)+1 种基金Scientific Research Project of Hunan Provincial Education Department,China(21B0238)The Science and Technology Innovation Program of Hunan Province(2021RC4062).
文摘Sodium silicate modification can improve the overall performance of wood.The modification process has a great influence on the properties of modified wood.In this study,a new method was introduced to analyze the wood modification process,and the properties of modified wood were studied.Poplar wood was modified with sodium silicate by vacuum-pressure impregnation.After screening using single-factor experiments,an orthogonal experiment was carried out with solution concentration,impregnation time,impregnation pressure,and the cycle times as experimental factors.The modified poplar with the best properties was selected by fuzzy mathematics and characterized by SEM,FT-IR,XRD and TG.The results showed that some lignin and hemicellulose were removed from the wood due to the alkaline action of sodium silicate,and the orderly crystal area of poplar became disorderly,resulting in the reduction of crystallinity of the modified poplar wood.FT-IR analysis showed that sodium silicate was hydrolyzed to form polysilicic acid in wood,and structural analysis revealed the formation of Si-O-Si and Si-O-C,indicating that sodium silicate reacted with fibers on the wood cell wall.TG-DTG curves showed that the final residual mass of modified poplar wood increased from 25%to 67%,and the temperature of the maximum loss rate decreased from 343℃ to 276℃.The heat release and smoke release of modified poplar wood decreased obviously.This kind of material with high strength and fire resistance can be used in the outdoor building and indoor furniture.
基金the National Scientific and Technological Project(No.MKPT-2004-09ZD)the Innovative Engineering Program of Central South University
文摘In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of warm compacted samples was studied. According to the orthogonal test method, the authors systematically study the influence of the different compaction pressure, condition of lubrication and compaction temperature on the green density of the sample in the warm compaction process, and put forward the optimal process parameter of warm compaction experiment. It is found that, a high compaction pressure （≥700 MPa）, die wall lubrication combined with a small amount of internal lubricants, and fitting compaction temperature by different condition of lubrication, are the optimal parameters in warm compaction process.
文摘The transfer function of the optical splitting system of the acousto-optic tunable filter （AOTF） is deduced to be a reference to optical design. The characteristic matrix （ transfer function） of AOTF is used to describe quantitatively the characters of polarization elements in the orthogonal polarizing system. According to the characteristic matrix, the included angle of polarizer＇s transmission direction and polarization analyzer＇s transmission direction should be 90°. As a result the signal to noise ratio increased about 20 times though the light intensity was reduced to 54.3%,because both the transmittances of polarizer and polarization analyzer are 0. 74, which is an intrinsic character. The orthogonal polarizing method is an effective method to get rid of the influence of zero order light and improve the spectrum resolution and signal-to-noise ratio.
基金Project supported by the National Natural Science Foundation of China
文摘In this paper, we reexamine the method of successive approximation presented by Prof. Chien Wei-zangfor solving the problem of large deflection of a circular plate, and find that the method could be regarded as the method of strained parameters in the singular perturbation theory. In terms of the parameter representing the ratio of the center deflection to the thickness of the plate, we make the asymptotic expansions of the deflection, membrane stress and the parameter of load as in Ref. [1], and then give the orthogonality conditions (i.e. the solvability conditions) for the resulting equations, by which the stiffness characteristics of the plate could be determined. It is pointed out that with the solutions for the small deflection problem of the circular plate and the orthogonality conditions, we can derive the third order approximate relations between the parameter of load and the center deflection and the first-term approximation of membrane stresses at the center and edge of the plate without solving the differential equations. For some special cases (i.e. under uniform load, under compound toad, with different boundary conditiors), we deduce the specific expressions and obtain the results in agreement with the previous ones given by Chien Wei-zang, Yeh kai-yuan and Hwang Chien in Refs. [1 - 4J.
文摘In this paper an orthogonal function method is presented based on the idea to suppose perioche sohuion with the method of harmonie balance The displaeement is expressed in the form of trigonometric fumctions a group of simplified digenequationsare obtained by the use of orthogonarity of trigonometric fumetions and linear mondes The method overcomes the diffieulty of a drifi term existing in systems with quadratic nonlinearities .The ealeulation examples show that the method has thd advantages of high caleulation preeision high convergenee speed and littld ealeulation work
文摘Finite element method (FEM) is an efficient numerical tool for the solution of partial differential equations (PDEs). It is one of the most general methods when compared to other numerical techniques. PDEs posed in a variational form over a given space, say a Hilbert space, are better numerically handled with the FEM. The FEM algorithm is used in various applications which includes fluid flow, heat transfer, acoustics, structural mechanics and dynamics, electric and magnetic field, etc. Thus, in this paper, the Finite Element Orthogonal Collocation Approach (FEOCA) is established for the approximate solution of Time Fractional Telegraph Equation (TFTE) with Mamadu-Njoseh polynomials as grid points corresponding to new basis functions constructed in the finite element space. The FEOCA is an elegant mixture of the Finite Element Method (FEM) and the Orthogonal Collocation Method (OCM). Two numerical examples are experimented on to verify the accuracy and rate of convergence of the method as compared with the theoretical results, and other methods in literature.
基金supported by Liao Ning Revitalization Talents Program(Grant No.XLYC1902068)the Science and Technology Partnership Program,Ministry of Science and Technology of China(Grant No.KY20202012)the Dalian University of Technology Basic Research Business Expense Project,Green Building Evaluation and BIM Intelligent Operation and Maintenance Control Platform Technology Development Service for Dalian Metro Line 5 Project Control Center of China Railway Dalian Metro Line No.5 Co.,LTD.,Xiajin County Public Medical Center Solar PVT Heat Pump Soil Cross-seasonal Energy Storage Low Carbon Energy Technology Service Project(Grant No.SDLS-2024012).
文摘Studies show that the photovoltaic-thermal(PVT)heat pump soil cross-seasonal energy storage system can effectively harness solar energy to supply heating,electricity,and cooling for buildings.The present study investigates a real-world application of this system in Dalian,China,outlining its design framework and optimizing key parameters using orthogonal methods.The factors examined include the area,slope angle,and azimuth angle of the PVT collectors,the flow rate through the PVT collectors,and the depth,spacing,count,and flow rate of the borehole.Through variance analysis,the influence of these parameters is evaluated on heat pump efficiency,soil temperature dynamics,and the system’s investment payback period.Findings indicate that borehole depth and PVT area are the dominant factors affecting the heating efficiency of the heat pump,contributing 66.86%and 16.25%,respectively.In the cooling efficiency of the heat pump,the most significant factors include borehole spacing(31.30%),borehole depth(26.36%),PVT area(16.98%),and borehole flow rate(16.67%).The investment payback period is primarily influenced by borehole depth(41.25%)and borehole quantity(25.24%),with PVT area and borehole spacing contributing 15.34%and 15.18%,respectively.Variations in soil temperature are largely governed by PVT area(40.85%)and borehole spacing(32.75%),followed by PVT slope angle(11.41%)and borehole depth(10.31%).The results of this research provide valuable insights for optimizing the design and implementation of PVT heat pump soil cross-seasonal energy storage systems scientifically and efficiently.
基金Project (No. 50278086) supported by the National Natural Science Foundation of China
文摘The construction of the cables is a key step for erecting suspen-dome structures. In practical engineering, it is difficult to ensure that the designed pre-stresses of cables have been exactly introduced into the structures in the site; so it is necessary to evaluate the influence of the variation of the pre-stresses on the structural behavior. In the present work, an orthogonal design method was employed to investigate the pre-stressed cables' sensitivity to the suspen-dome system. The investigation was concentrated on a Kiewitt suspen-dome. Parametric studies were carried out to study the sensitivity of the structure's static behavior, dynamic behavior, and buckling loads when the pre-stresses in the cables varied. The investigation indicated that suspen-dome structures are sensitive to the pre-stresses in all cables; and that the sensitivity depended on the location of the cables and the kind of structural behavior. Useful suggestions are given at the end of the paper.
基金This project is supported by National Natural Science Foundation of China (No.59905018) Provincial Excellent Young Scientist Foundation of Shandong (No.01BS033).
文摘A new method named orthogonal two-way link-shift here has been proposed.Based on the method and a standard involute gear hob, a specific gear tooth profile (including anarbitrary gear tooth profile and a modified involute gear tooth profile) can be generated on aCNC(computer numerical control) bobbing machine. Computer simulation has been carried out, and theresults prove that the method is right and practicable. So, the fabrication costs can be greatlydecreased than before. The new method has momentous significance to realize gear's optimizedmodification under different work conditions.
文摘a new strategy combining an expert system and improved genetic algorithms is presented for tuning proportional-integral-derivative （PID） parameters for petrochemical processes. This retains the advantages of genetic algorithms, namely rapid convergence and attainment of the global optimum. Utilization of an orthogonal experiment method solves the determination of the genetic factors. Combination with an expert system can make best use of the actual experience of the plant operators. Simulation results of typical process systems examples show a good control performance and robustness.
基金supported by the Natural Science Foundation of Guangdong Province(No.2019A1515012040).
文摘As a typical laser additive manufacturing technology,laser powder bed fusion(LPBF)has achieved demonstration applications in aerospace,biomedical and other fields.However,how to select process parameters quickly and reasonably is still themain concern of LPBF production.In order to quantitatively analyze the influence of different process parameters(laser power,scanning speed,hatch space and layer thickness)on the LPBF process,the multilayer and multi-path forming process of LPBF was predicted based on the open-source discrete element method framework Yade and the open-source finite volume method framework OpenFOAM.Based on the design of experiments method,a four-factor three-level orthogonal test scheme was designed,and the porosity and surface roughness data of each calculation scheme were extracted.By analyzing the orthogonal test data,it was found that as the laser power increased,the porosity decreased,and as the scanning speed,hatch space,and layer thickness increased,the porosity increased.In addition,the influence of laser power and scanning speed on surface roughness showed a trend of decreasing first and then increasing,while the influence of scanning distance and layer thickness on surface roughness showed amonotonous increasing trend.The order of the influence of each process parameter on porosity was:scanning speed>laying thickness>laser power>hatch space,and the order of the influence of each process parameter on surface roughness was:hatch space>layer thickness>laser power>scanning speed.So the porosity of the part is most sensitive to scanning speed,and the surface roughness is the most sensitive to hatch space.The above conclusions are expected to provide process control basis for actual LPBF production of the 316L stainless steel alloy.
基金The National Key Research and Development Program of China(No.2017YFC0805103)the National Natural Science Foundation of China(No.51578137,51438002,51108075)the Open Research Fund Program of Jiangsu Key Laboratory of Engineering Mechanics
文摘A modified Gurson-Tvergaard-Needleman(GTN)model that accounts for the mixed(isotropic and kinematic)hardening of cast steel GS-20Mn5V was developed and implemented in the finite dement program ABAQUS/Standard via a user-defined material subroutine UMAT.This model couples the stress state and damage evolution(pore volume fraction increase)by a classic method that assumes that the total void volume fraction is divided into a nucleation and a growth part.A parametric study was conducted to assess the effect of modified GTN model parameters on mechanical properties such as the nucleation,growth and coalescence of voids and to obtain the optimal parameter combination by the orthogonal test method.The predicted load-displacement curves of notched specimens with the optimal parameters are favorably compared to the experimental curves.Therefore,the modified GTN model can be used to predict the damage evaluation and fracture behavior of GS-20Mn5V.
基金supported by the National Science Foundation of China(11271127 and 11061009)Science Research Program of Guizhou(GJ[2011]2367)the Co-Construction Project of Beijing Municipal Commission of Education
文摘In this paper, we extend the applications of proper orthogonal decomposition （POD） method, i.e., apply POD method to a mixed finite element （MFE） formulation naturally satisfied Brezz-Babu^ka for parabolic equations, establish a reduced-order MFE formulation with lower dimensions and sufficiently high accuracy, and provide the error estimates between the reduced-order POD MFE solutions and the classical MFE solutions and the implementation of algorithm for solving reduced-order MFE formulation. Some numerical examples illustrate the fact that the results of numerical computation are consis- tent with theoretical conclusions. Moreover, it is shown that the new reduced-order MFE formulation based on POD method is feasible and efficient for solving MFE formulation for parabolic equations.
基金the National High Technology Research and Development Program (863) of China(No.2007AA05Z215)
文摘The objective of this paper is to optimize the parameters of pellet drying and preheating process in grate.A mathematical model of drying and preheating is developed,and is verified by the experiments.Further,the operating parameters of wind temperature,wind speed,grate speed and bed depth etc.are investigated through the orthogonal method using the simulation results.And a relationship of drying,preheating effects and operating parameters is achieved.The results show that the optimization effect can be achieved in the given range when air velocity is about 3.0 m/s and temperature is about 300,500,800,and 1 100 in the updraft drying zone,downdraft drying zone,preheating Ⅰ zone,and preheating Ⅱ zone respectively.The work is help for saving energy and reducing emissions in pellet induration.
