Variable stiffness composites present a promising solution for mitigating impact loads via varying the fiber volume fraction layer-wise,thereby adjusting the panel's stiffness.Since each layer of the composite may...Variable stiffness composites present a promising solution for mitigating impact loads via varying the fiber volume fraction layer-wise,thereby adjusting the panel's stiffness.Since each layer of the composite may be affected by a different failure mode,the optimal fiber volume fraction to suppress damage initiation and evolution is different across the layers.This research examines how re-allocating the fibers layer-wise enhances the composites'impact resistance.In this study,constant stiffness panels with the same fiber volume fraction throughout the layers are compared to variable stiffness ones by varying volume fraction layer-wise.A method is established that utilizes numerical analysis coupled with optimization techniques to determine the optimal fiber volume fraction in both scenarios.Three different reinforcement fibers(Kevlar,carbon,and glass)embedded in epoxy resin were studied.Panels were manufactured and tested under various loading conditions to validate results.Kevlar reinforcement revealed the highest tensile toughness,followed by carbon and then glass fibers.Varying reinforcement volume fraction significantly influences failure modes.Higher fractions lead to matrix cracking and debonding,while lower fractions result in more fiber breakage.The optimal volume fraction for maximizing fiber breakage energy is around 45%,whereas it is about 90%for matrix cracking and debonding.A drop tower test was used to examine the composite structure's behavior under lowvelocity impact,confirming the superiority of Kevlar-reinforced composites with variable stiffness.Conversely,glass-reinforced composites with constant stiffness revealed the lowest performance with the highest deflection.Across all reinforcement materials,the variable stiffness structure consistently outperformed its constant stiffness counterpart.展开更多
Biomass-based hydrocarbon fuels,as one of the alternatives to traditional fossil fuels,have attracted considerable attention in the energy field due to their renewability and environmental benefits.This article provid...Biomass-based hydrocarbon fuels,as one of the alternatives to traditional fossil fuels,have attracted considerable attention in the energy field due to their renewability and environmental benefits.This article provides a systematic review of recent research progress in the chemical synthesis of biomass-based hydrocarbon fuels.It outlines the conversion pathways using feedstocks such as lipids,terpenoids,cellulose/hemicellulose,and lignin.Depending on the feedstock,various products with distinct structural characteristics can be prepared through reactions such as cyclization,condensation,and catalytic hydrogenation.Throughout the synthesis process,three key factors play a critical role:efficient catalyst development,production process optimization,and computational-chemistry-based molecular design.Finally,the article discusses future perspectives for biomass-based hydrocarbon fuel synthesis research.展开更多
Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durabili...Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durability,and corrosion resistance.These metals have body-centered cubic crystal structure,characterized by limited slip systems and impeded dislocation motion,resulting in significant low-temperature brittleness,which poses challenges for the conventional processing.Additive manufacturing technique provides an innovative approach,enabling the production of intricate parts without molds,which significantly improves the efficiency of material usage.This review provides a comprehensive overview of the advancements in additive manufacturing techniques for the production of refractory metals,such as W,Ta,Mo,and Nb,particularly the laser powder bed fusion.In this review,the influence mechanisms of key process parameters(laser power,scan strategy,and powder characteristics)on the evolution of material microstructure,the formation of metallurgical defects,and mechanical properties were discussed.Generally,optimizing powder characteristics,such as sphericity,implementing substrate preheating,and formulating alloying strategies can significantly improve the densification and crack resistance of manufactured parts.Meanwhile,strictly controlling the oxygen impurity content and optimizing the energy density input are also the key factors to achieve the simultaneous improvement in strength and ductility of refractory metals.Although additive manufacturing technique provides an innovative solution for processing refractory metals,critical issues,such as residual stress control,microstructure and performance anisotropy,and process stability,still need to be addressed.This review not only provides a theoretical basis for the additive manufacturing of high-performance refractory metals,but also proposes forward-looking directions for their industrial application.展开更多
The volatilization characteristics and kinetic mechanisms of arsenic were investigated in the temperature range of 623−773 K and pressure ranges of 10−10000 Pa.The experimental results reveal that the evaporation rate...The volatilization characteristics and kinetic mechanisms of arsenic were investigated in the temperature range of 623−773 K and pressure ranges of 10−10000 Pa.The experimental results reveal that the evaporation rate increases with increasing temperature and decreasing pressure.Surface reaction control dominates at low pressures(<100 Pa),whereas diffusion control dominates at high pressures(>5000 Pa).The evaporation behavior is successfully described by an Arrhenius-type model for temperature dependence and Logistic model for pressure dependence.Key kinetic parameters,including the critical pressure,maximum evaporation rate and evaporation coefficient,were calculated.The evaporation coefficient varies between 0.010 and 0.223,and the critical pressures vary between 281 and 478 Pa with temperature.展开更多
Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentrat...Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.展开更多
Machine learning-assisted methods for rapid and accurate prediction of temperature field,mushy zone,and grain size were proposed for the heating−cooling combined mold(HCCM)horizontal continuous casting of C70250 alloy...Machine learning-assisted methods for rapid and accurate prediction of temperature field,mushy zone,and grain size were proposed for the heating−cooling combined mold(HCCM)horizontal continuous casting of C70250 alloy plates.First,finite element simulations of casting processes were carried out with various parameters to build a dataset.Subsequently,different machine learning algorithms were employed to achieve high precision in predicting temperature fields,mushy zone locations,mushy zone inclination angle,and billet grain size.Finally,the process parameters were quickly optimized using a strategy consisting of random generation,prediction,and screening,allowing the mushy zone to be controlled to the desired target.The optimized parameters are 1234℃for heating mold temperature,47 mm/min for casting speed,and 10 L/min for cooling water flow rate.The optimized mushy zone is located in the middle of the second heat insulation section and has an inclination angle of roughly 7°.展开更多
Low pressure chemical vapor deposition(LPCVD) is one of the most important processes during semiconductor manufacturing.However,the spatial distribution of internal temperature and extremely few samples makes it hard ...Low pressure chemical vapor deposition(LPCVD) is one of the most important processes during semiconductor manufacturing.However,the spatial distribution of internal temperature and extremely few samples makes it hard to build a good-quality model of this batch process.Besides,due to the properties of this process,the reliability of the model must be taken into consideration when optimizing the MVs.In this work,an optimal design strategy based on the self-learning Gaussian process model(GPM) is proposed to control this kind of spatial batch process.The GPM is utilized as the internal model to predict the thicknesses of thin films on all spatial-distributed wafers using the limited data.Unlike the conventional model based design,the uncertainties of predictions provided by GPM are taken into consideration to guide the optimal design of manipulated variables so that the designing can be more prudent Besides,the GPM is also actively enhanced using as little data as possible based on the predictive uncertainties.The effectiveness of the proposed strategy is successfully demonstrated in an LPCVD process.展开更多
Based on macroscopic and synthetic approaches, especially information entropy approach, the quantification of the flexible degree and order degree of business processes is studied. According to the outcome of above an...Based on macroscopic and synthetic approaches, especially information entropy approach, the quantification of the flexible degree and order degree of business processes is studied. According to the outcome of above analysis, a conceptual model of optimizing business processes is proposed which supports to construct dynamic stable business processes. The research above has been applied in project 863/SDDAC-CIMS, and achieved primary benefits.展开更多
Background Acute myocardial infarction is a common and prevalent cardiovascular disease that can lead to serious consequences such as shock,arrhythmia,and heart failure.In dealing with acute myocardial infarction,the ...Background Acute myocardial infarction is a common and prevalent cardiovascular disease that can lead to serious consequences such as shock,arrhythmia,and heart failure.In dealing with acute myocardial infarction,the optimization of emergency nursing process can ensure the effectiveness and safety of rescue work,and help improve the prognosis and rehabilitation of patients.Methods 68 cases of patients with acute myocardial infarction admitted to our hospital from August 2021 to March 2023 were selected as the subjects of this study.They were randomly divided into an observation group and a control group,with 34 cases in each group.The control group received routine nursing care,while the observation group received optimized emergency nursing process based on it.the success rates of rescue,emergency efficiency,complications,and hemodynamics were compared between the two groups.ResultsThe success rate of rescue in the observation group was 100.00%,while in the control group it was 88.24%,the success rate of rescue was statistically different between the two groups(P<0.05).The observation group had shorter time intervals from onset to hospital admission,shorter door-to-activation time,shorter door-toballoon time,and reduced length of hospital stay compared to the control group(P<0.05).The total proportion of patients with complications such as arrhythmias in the observation group was 0.00%,while in the control group it was 11.76%,the difference between the two groups was statistically significant(P<0.05).The Cardi-ac output(CO)index of the observation group and the control group is lower than before the nursing intervention,and the observation group is higher than the control group.The Mean arterial pressure(MAP)index of the observation group and the control group is lower than before the nursing intervention,and the observation group is lower than the control group(P<0.05).Conclusions Optimized the emergency nursing process can improve the success rate of rescue and emergency efficiency in patients with acute myocardial infarction,reduce the occurrence of adverse complications,and improve negative emotions such as anxiety.It is worth promoting and applying.展开更多
Objective: to study the optimization method of outpatient triage process and its practical application value. Methods: from January, 2020 to December, 2020, 200 outpatients in our hospital were selected as the general...Objective: to study the optimization method of outpatient triage process and its practical application value. Methods: from January, 2020 to December, 2020, 200 outpatients in our hospital were selected as the general group, and the patients were treated by the traditional process. From January, 2021 to December, 2021, 200 outpatients in our hospital were selected as the optimization group, and patients were given process optimization during outpatient treatment, which mainly included optimizing the triage desk environment, rationally allocating triage nurses resources, improving triage nurses communication skills, and constructing information triage process. The triage accuracy rate of two groups of patients was counted, and the registration time, waiting time for auxiliary examination and treatment time of two groups of patients were counted, to investigate the satisfaction of two groups of patients with outpatient triage service and the occurrence of nurse-patient disputes. Results: the accuracy rate of triage in the optimized group was 95%, which was higher than 81% in the general group (P < 0.05). The registration time, waiting time for auxiliary examination and visiting time of patients in the optimized group were shorter than those in the general group (P < 0.05). Patients satisfaction with the rationality of outpatient triage process in the optimized group was 94%, which was higher than that in the general group (76%, P < 0.05). The patients satisfaction with the convenience of outpatient triage process in the optimized group was 96%, which was higher than that in the general group (74%, P < 0.05). There were 10 cases of nurse-patient disputes in the general group, with a nurse-patient dispute rate of 5%, and 1 case in the optimized group, with a nurse-patient dispute rate of 0.5%. The nurse-patient dispute rate in the optimized group was lower than that in the general group (P < 0.05). Conclusion: in outpatient triage service, process optimization through resource integration, strengthening nurse-patient communication, strengthening information construction and optimizing post allocation can effectively improve triage accuracy and patient treatment efficiency, improve patient nursing satisfaction and prevent nurse-patient disputes.展开更多
Objective:To analyze the effect of optimizing the emergency nursing process in the resuscitation of patients with acute chest pain and the impact on the resuscitation success rate.Methods:66 patients with acute chest ...Objective:To analyze the effect of optimizing the emergency nursing process in the resuscitation of patients with acute chest pain and the impact on the resuscitation success rate.Methods:66 patients with acute chest pain received by the emergency department of our hospital from January 2022 to December 2023 were selected as the study subjects and divided into two groups according to the differences in the emergency nursing process,i.e.,33 patients receiving routine emergency care were included in the control group,and 33 patients receiving the optimization of emergency nursing process intervention were included in the observation group.Patients’resuscitation effect and satisfaction with nursing care in the two groups were compared.Results:The observation group’s consultation assessment time,reception time,admission to the start of resuscitation time,and resuscitation time were shorter than that of the control group,the resuscitation success rate was higher than that of the control group,and the incidence of adverse events was lower than that of the control group,with statistically significant differences(P<0.05);and the observation group’s satisfaction with nursing care was higher than that of the control group,with statistically significant differences(P<0.05).Conclusion:Optimization of emergency nursing process intervention in the resuscitation of acute chest pain patients can greatly shorten the rescue time and improve the success rate of resuscitation,with higher patient satisfaction.展开更多
In wire arc additive manufacturing(WAAM),a trade-off exists among deposition efficiency,microstructure,and mechanical properties.Addressing this challenge,this work proposes an innovative multi-objective optimization ...In wire arc additive manufacturing(WAAM),a trade-off exists among deposition efficiency,microstructure,and mechanical properties.Addressing this challenge,this work proposes an innovative multi-objective optimization framework tailored for WAAM of AZ31 magnesium alloy components,which integrates deposition efficiency and microstructure as coupled objectives and is resolved through the NSGA-Ⅱ algorithm.The proposed framework employs quadratic regression to correlate process parameters with deposition efficiency through geometric morphology mediation,while addressing uncertainties in WAAM by integrating theoretical insights with data-driven stacked ensemble learning for grain size prediction,establishing the hybrid physics-informed data method for WAAM microstructure prediction.The optimized process achieved a deposition rate of 6257 mm3/min,with effective width and average layer height maintained at 10.1 mm and 4.13 mm,respectively.Microstructural optimization produced a fine,uniform,fully equiaxed grain structure with an average grain size of 38μm.These findings underscore the significant industrial potential of intelligent optimization strategies in WAAM for manufacturing lightweight,high-performance components in aerospace and transportation sectors.展开更多
Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects s...Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.展开更多
The integration of artificial intelligence into the development and production of mechatronic products offers a substantial opportunity to enhance efficiency, adaptability, and system performance. This paper examines ...The integration of artificial intelligence into the development and production of mechatronic products offers a substantial opportunity to enhance efficiency, adaptability, and system performance. This paper examines the utilization of reinforcement learning as a control strategy, with a particular focus on its deployment in pivotal stages of the product development lifecycle, specifically between system architecture and system integration and verification. A controller based on reinforcement learning was developed and evaluated in comparison to traditional proportional-integral controllers in dynamic and fault-prone environments. The results illustrate the superior adaptability, stability, and optimization potential of the reinforcement learning approach, particularly in addressing dynamic disturbances and ensuring robust performance. The study illustrates how reinforcement learning can facilitate the transition from conceptual design to implementation by automating optimization processes, enabling interface automation, and enhancing system-level testing. Based on the aforementioned findings, this paper presents future directions for research, which include the integration of domain-specific knowledge into the reinforcement learning process and the validation of this process in real-world environments. The results underscore the potential of artificial intelligence-driven methodologies to revolutionize the design and deployment of intelligent mechatronic systems.展开更多
1.Colors of chemical reaction engineering models Kinetic models of chemical reactions are a crucial asset for understanding and optimizing chemical processes[1].These models are critical for reactor design,process opt...1.Colors of chemical reaction engineering models Kinetic models of chemical reactions are a crucial asset for understanding and optimizing chemical processes[1].These models are critical for reactor design,process optimization,catalyst design,scale-up,and process control,making them indispensable in the chemical industry.Kinetic models predict the change in temperature and concentration of the relevant species,given an actual concentration and temperature.Reaction predictions are made by integrating the kinetic model with a reactor model,which accounts for external constraints,such as flow,inlet concentration。展开更多
Fiber quality measurement in spinning preparation is crucial for optimizing waste and meeting yarn quality specifications.The brand-new Uster AFIS 6–the next-generation laboratory instrument from Uster Technologies–...Fiber quality measurement in spinning preparation is crucial for optimizing waste and meeting yarn quality specifications.The brand-new Uster AFIS 6–the next-generation laboratory instrument from Uster Technologies–uniquely tests man-made fiber properties in addition to cotton.It provides critical data to optimize fiber process control for cotton,man-made fibers,and blended yarns.展开更多
Objective:To investigate the application effects of intelligent guidance systems in optimizing health check-up process management.Methods:A total of 400 examinees who underwent physical examinations at the hospital’s...Objective:To investigate the application effects of intelligent guidance systems in optimizing health check-up process management.Methods:A total of 400 examinees who underwent physical examinations at the hospital’s Health Management Center from January to December 2024 were randomly divided into a control group(200 cases)and an observation group(200 cases).The control group used traditional manual guidance methods,while the observation group employed the intelligent guidance system.The study compared two groups in terms of completion time,waiting time for each procedure,check-up efficiency scores,examinee satisfaction,and report issuance time.Results:The overall examination time in the observation group(85.3±12.7 minutes)was significantly shorter than that in the control group(142.6±18.5 minutes)(P<0.01);average waiting time per procedure decreased by 62.4%;check-up efficiency scores(8.9±0.8 points)were significantly higher than those in the control group(5.2±1.1 points)(P<0.01);satisfaction reached 96.5%,significantly higher than the control group’s 78.0%(P<0.01);and report issuance time was advanced by 1.5 days.Conclusion:Intelligent guidance systems can significantly optimize check-up processes,improve work efficiency,and examinee satisfaction,demonstrating significant clinical application value.展开更多
The latest progress in the process optimization and stability improvement of third-generation cephalosporins in recent years was reviewed.The introduction of green chemistry,enzyme catalysis,nanotechnology,lyophilizat...The latest progress in the process optimization and stability improvement of third-generation cephalosporins in recent years was reviewed.The introduction of green chemistry,enzyme catalysis,nanotechnology,lyophilization,and nitrogen-filled packaging technologies can only improve production efficiency and reduce the generation of by-products,but also significantly extend the shelf life of drugs.In the future,process automation and intelligent technology will further optimize the large-scale production process,and the combination of nanotechnology and precision drug delivery will promote the improvement of effect in clinical applications.展开更多
Diaphragma juglandis(D.juglandis)Fructus is a brownish lamellar structure located between walnut kernels.As a traditional Chinese herbal medicine,it exhibits therapeutic effects including spleen-strengthening,kidney c...Diaphragma juglandis(D.juglandis)Fructus is a brownish lamellar structure located between walnut kernels.As a traditional Chinese herbal medicine,it exhibits therapeutic effects including spleen-strengthening,kidney consolidation,astringency,diuresis,and heat-clearing.In this study,the polyphenolic constituents of D.juglandis and its functional instant tea were investigated in this study.Three polyphenolic compounds were isolated from 70%ethanol extract of D.juglandis Fructus as 2-methoxy juglone,regiolone and quercetin.The HPLC method was established for determination of the content of quercetin in the instant tea samples under the premise that the methodology was verifi ed to meet the standard requirements.The preparation process of D.juglandis Fructus instant tea was optimized through single factor experiments and Box-Behnken design-response surface methodology and the optimal conditions were determined as follows:feed rate of 10 mL/min,inlet temperature of 151℃,andβ-cyclodextrin addition of 9%.Then the antioxidant activity of each sample was evaluated using DPPH and ABTS radical scavenging assays.The results showed that the quercetin had significant antioxidant activity.The instant tea group demonstrated superior antioxidant effects compared to the extracts group at 50,200,and 800μg/mL(P<0.001),likely due to the optimized spray-drying process,which might have enhanced the solubility,stability,and bioavailability of the active compounds.The results provided critical foundational data for the deep processing and comprehensive utilization of D.juglandis Fructus.展开更多
High ammonia-nitrogen digestate has become a key bottleneck limiting the anaerobic digestion of organic solid waste.Vacuum ammonia stripping can simultaneously remove and recover ammonia nitrogen,which has attracted a...High ammonia-nitrogen digestate has become a key bottleneck limiting the anaerobic digestion of organic solid waste.Vacuum ammonia stripping can simultaneously remove and recover ammonia nitrogen,which has attracted a lot of attention in recent years.To investigate the parameter effects on the efficiency and mass transfer,five combination conditions(53℃ 15 kPa,60°C 20 kPa,65°C 25 kPa,72°C 35 kPa,and 81°C 50 kPa)were conducted for ammonia stripping of sludge digestate.The results showed that 80%of ammonia nitrogen was stripped in 45 min for all experimental groups,but the ammonia transfer coefficient varied under different conditions,which increased with the rising of boiling point temperature,and reached the maximum value(39.0 mm/hr)at 81°C 50 kPa.The ammonia nitrogen removal efficiency was more than 80%for 30 min vacuum stripping after adjusting the initial pH to above 9.5,and adjustment of the initial alkalinity also affects the pH value of liquid digestate.It was found that pH and alkalinity are the key factors influencing the ammonia nitrogen dissociation and removal efficiency,while temperature and vacuum mainly affect the ammonia nitrogen mass transfer and removal velocity.In terms of the mechanism of vacuum ammonia stripping,it underwent alkalinity destruction,pH enhancement,ammonia nitrogen dissociation,and free ammonia removal.In this study,two-stage experiments of alkalinity destruction and ammonia removal were also carried out,which showed that the two-stage configuration was beneficial for ammonia removal.It provides a theoretical basis and practical technology for the vacuum ammonia stripping from liquid digestate of organic solid waste.展开更多
基金funded by the American University of Sharjah.United Arab Emirates award number EN 9502-FRG19-M-E75。
文摘Variable stiffness composites present a promising solution for mitigating impact loads via varying the fiber volume fraction layer-wise,thereby adjusting the panel's stiffness.Since each layer of the composite may be affected by a different failure mode,the optimal fiber volume fraction to suppress damage initiation and evolution is different across the layers.This research examines how re-allocating the fibers layer-wise enhances the composites'impact resistance.In this study,constant stiffness panels with the same fiber volume fraction throughout the layers are compared to variable stiffness ones by varying volume fraction layer-wise.A method is established that utilizes numerical analysis coupled with optimization techniques to determine the optimal fiber volume fraction in both scenarios.Three different reinforcement fibers(Kevlar,carbon,and glass)embedded in epoxy resin were studied.Panels were manufactured and tested under various loading conditions to validate results.Kevlar reinforcement revealed the highest tensile toughness,followed by carbon and then glass fibers.Varying reinforcement volume fraction significantly influences failure modes.Higher fractions lead to matrix cracking and debonding,while lower fractions result in more fiber breakage.The optimal volume fraction for maximizing fiber breakage energy is around 45%,whereas it is about 90%for matrix cracking and debonding.A drop tower test was used to examine the composite structure's behavior under lowvelocity impact,confirming the superiority of Kevlar-reinforced composites with variable stiffness.Conversely,glass-reinforced composites with constant stiffness revealed the lowest performance with the highest deflection.Across all reinforcement materials,the variable stiffness structure consistently outperformed its constant stiffness counterpart.
基金Support by National Natural Science Foundation of China(22127802,22573091)the HY Action(62402010305)。
文摘Biomass-based hydrocarbon fuels,as one of the alternatives to traditional fossil fuels,have attracted considerable attention in the energy field due to their renewability and environmental benefits.This article provides a systematic review of recent research progress in the chemical synthesis of biomass-based hydrocarbon fuels.It outlines the conversion pathways using feedstocks such as lipids,terpenoids,cellulose/hemicellulose,and lignin.Depending on the feedstock,various products with distinct structural characteristics can be prepared through reactions such as cyclization,condensation,and catalytic hydrogenation.Throughout the synthesis process,three key factors play a critical role:efficient catalyst development,production process optimization,and computational-chemistry-based molecular design.Finally,the article discusses future perspectives for biomass-based hydrocarbon fuel synthesis research.
基金National MCF Energy R&D Program(2024YFE03260300)。
文摘Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durability,and corrosion resistance.These metals have body-centered cubic crystal structure,characterized by limited slip systems and impeded dislocation motion,resulting in significant low-temperature brittleness,which poses challenges for the conventional processing.Additive manufacturing technique provides an innovative approach,enabling the production of intricate parts without molds,which significantly improves the efficiency of material usage.This review provides a comprehensive overview of the advancements in additive manufacturing techniques for the production of refractory metals,such as W,Ta,Mo,and Nb,particularly the laser powder bed fusion.In this review,the influence mechanisms of key process parameters(laser power,scan strategy,and powder characteristics)on the evolution of material microstructure,the formation of metallurgical defects,and mechanical properties were discussed.Generally,optimizing powder characteristics,such as sphericity,implementing substrate preheating,and formulating alloying strategies can significantly improve the densification and crack resistance of manufactured parts.Meanwhile,strictly controlling the oxygen impurity content and optimizing the energy density input are also the key factors to achieve the simultaneous improvement in strength and ductility of refractory metals.Although additive manufacturing technique provides an innovative solution for processing refractory metals,critical issues,such as residual stress control,microstructure and performance anisotropy,and process stability,still need to be addressed.This review not only provides a theoretical basis for the additive manufacturing of high-performance refractory metals,but also proposes forward-looking directions for their industrial application.
基金Yunnan Fundamental Research Project,China(No.202201BE070001-056)。
文摘The volatilization characteristics and kinetic mechanisms of arsenic were investigated in the temperature range of 623−773 K and pressure ranges of 10−10000 Pa.The experimental results reveal that the evaporation rate increases with increasing temperature and decreasing pressure.Surface reaction control dominates at low pressures(<100 Pa),whereas diffusion control dominates at high pressures(>5000 Pa).The evaporation behavior is successfully described by an Arrhenius-type model for temperature dependence and Logistic model for pressure dependence.Key kinetic parameters,including the critical pressure,maximum evaporation rate and evaporation coefficient,were calculated.The evaporation coefficient varies between 0.010 and 0.223,and the critical pressures vary between 281 and 478 Pa with temperature.
基金supported by the National Key Research and Development Program of China(Grant No.2023YFB3710805).
文摘Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.
基金financially supported by the National Key Research and Development Program of China (No. 2023YFB3812601)the National Natural Science Foundation of China (No. 51925401)the Young Elite Scientists Sponsorship Program by CAST, China (No. 2022QNRC001)。
文摘Machine learning-assisted methods for rapid and accurate prediction of temperature field,mushy zone,and grain size were proposed for the heating−cooling combined mold(HCCM)horizontal continuous casting of C70250 alloy plates.First,finite element simulations of casting processes were carried out with various parameters to build a dataset.Subsequently,different machine learning algorithms were employed to achieve high precision in predicting temperature fields,mushy zone locations,mushy zone inclination angle,and billet grain size.Finally,the process parameters were quickly optimized using a strategy consisting of random generation,prediction,and screening,allowing the mushy zone to be controlled to the desired target.The optimized parameters are 1234℃for heating mold temperature,47 mm/min for casting speed,and 10 L/min for cooling water flow rate.The optimized mushy zone is located in the middle of the second heat insulation section and has an inclination angle of roughly 7°.
基金Supported by the National High Technology Research and Development Program of China(2014AA041803)the National Natural Science Foundation of China(61320106009)
文摘Low pressure chemical vapor deposition(LPCVD) is one of the most important processes during semiconductor manufacturing.However,the spatial distribution of internal temperature and extremely few samples makes it hard to build a good-quality model of this batch process.Besides,due to the properties of this process,the reliability of the model must be taken into consideration when optimizing the MVs.In this work,an optimal design strategy based on the self-learning Gaussian process model(GPM) is proposed to control this kind of spatial batch process.The GPM is utilized as the internal model to predict the thicknesses of thin films on all spatial-distributed wafers using the limited data.Unlike the conventional model based design,the uncertainties of predictions provided by GPM are taken into consideration to guide the optimal design of manipulated variables so that the designing can be more prudent Besides,the GPM is also actively enhanced using as little data as possible based on the predictive uncertainties.The effectiveness of the proposed strategy is successfully demonstrated in an LPCVD process.
文摘Based on macroscopic and synthetic approaches, especially information entropy approach, the quantification of the flexible degree and order degree of business processes is studied. According to the outcome of above analysis, a conceptual model of optimizing business processes is proposed which supports to construct dynamic stable business processes. The research above has been applied in project 863/SDDAC-CIMS, and achieved primary benefits.
文摘Background Acute myocardial infarction is a common and prevalent cardiovascular disease that can lead to serious consequences such as shock,arrhythmia,and heart failure.In dealing with acute myocardial infarction,the optimization of emergency nursing process can ensure the effectiveness and safety of rescue work,and help improve the prognosis and rehabilitation of patients.Methods 68 cases of patients with acute myocardial infarction admitted to our hospital from August 2021 to March 2023 were selected as the subjects of this study.They were randomly divided into an observation group and a control group,with 34 cases in each group.The control group received routine nursing care,while the observation group received optimized emergency nursing process based on it.the success rates of rescue,emergency efficiency,complications,and hemodynamics were compared between the two groups.ResultsThe success rate of rescue in the observation group was 100.00%,while in the control group it was 88.24%,the success rate of rescue was statistically different between the two groups(P<0.05).The observation group had shorter time intervals from onset to hospital admission,shorter door-to-activation time,shorter door-toballoon time,and reduced length of hospital stay compared to the control group(P<0.05).The total proportion of patients with complications such as arrhythmias in the observation group was 0.00%,while in the control group it was 11.76%,the difference between the two groups was statistically significant(P<0.05).The Cardi-ac output(CO)index of the observation group and the control group is lower than before the nursing intervention,and the observation group is higher than the control group.The Mean arterial pressure(MAP)index of the observation group and the control group is lower than before the nursing intervention,and the observation group is lower than the control group(P<0.05).Conclusions Optimized the emergency nursing process can improve the success rate of rescue and emergency efficiency in patients with acute myocardial infarction,reduce the occurrence of adverse complications,and improve negative emotions such as anxiety.It is worth promoting and applying.
文摘Objective: to study the optimization method of outpatient triage process and its practical application value. Methods: from January, 2020 to December, 2020, 200 outpatients in our hospital were selected as the general group, and the patients were treated by the traditional process. From January, 2021 to December, 2021, 200 outpatients in our hospital were selected as the optimization group, and patients were given process optimization during outpatient treatment, which mainly included optimizing the triage desk environment, rationally allocating triage nurses resources, improving triage nurses communication skills, and constructing information triage process. The triage accuracy rate of two groups of patients was counted, and the registration time, waiting time for auxiliary examination and treatment time of two groups of patients were counted, to investigate the satisfaction of two groups of patients with outpatient triage service and the occurrence of nurse-patient disputes. Results: the accuracy rate of triage in the optimized group was 95%, which was higher than 81% in the general group (P < 0.05). The registration time, waiting time for auxiliary examination and visiting time of patients in the optimized group were shorter than those in the general group (P < 0.05). Patients satisfaction with the rationality of outpatient triage process in the optimized group was 94%, which was higher than that in the general group (76%, P < 0.05). The patients satisfaction with the convenience of outpatient triage process in the optimized group was 96%, which was higher than that in the general group (74%, P < 0.05). There were 10 cases of nurse-patient disputes in the general group, with a nurse-patient dispute rate of 5%, and 1 case in the optimized group, with a nurse-patient dispute rate of 0.5%. The nurse-patient dispute rate in the optimized group was lower than that in the general group (P < 0.05). Conclusion: in outpatient triage service, process optimization through resource integration, strengthening nurse-patient communication, strengthening information construction and optimizing post allocation can effectively improve triage accuracy and patient treatment efficiency, improve patient nursing satisfaction and prevent nurse-patient disputes.
文摘Objective:To analyze the effect of optimizing the emergency nursing process in the resuscitation of patients with acute chest pain and the impact on the resuscitation success rate.Methods:66 patients with acute chest pain received by the emergency department of our hospital from January 2022 to December 2023 were selected as the study subjects and divided into two groups according to the differences in the emergency nursing process,i.e.,33 patients receiving routine emergency care were included in the control group,and 33 patients receiving the optimization of emergency nursing process intervention were included in the observation group.Patients’resuscitation effect and satisfaction with nursing care in the two groups were compared.Results:The observation group’s consultation assessment time,reception time,admission to the start of resuscitation time,and resuscitation time were shorter than that of the control group,the resuscitation success rate was higher than that of the control group,and the incidence of adverse events was lower than that of the control group,with statistically significant differences(P<0.05);and the observation group’s satisfaction with nursing care was higher than that of the control group,with statistically significant differences(P<0.05).Conclusion:Optimization of emergency nursing process intervention in the resuscitation of acute chest pain patients can greatly shorten the rescue time and improve the success rate of resuscitation,with higher patient satisfaction.
基金supported by the National Natural Science Foundation of China(Nos.52475317 and 52305331).
文摘In wire arc additive manufacturing(WAAM),a trade-off exists among deposition efficiency,microstructure,and mechanical properties.Addressing this challenge,this work proposes an innovative multi-objective optimization framework tailored for WAAM of AZ31 magnesium alloy components,which integrates deposition efficiency and microstructure as coupled objectives and is resolved through the NSGA-Ⅱ algorithm.The proposed framework employs quadratic regression to correlate process parameters with deposition efficiency through geometric morphology mediation,while addressing uncertainties in WAAM by integrating theoretical insights with data-driven stacked ensemble learning for grain size prediction,establishing the hybrid physics-informed data method for WAAM microstructure prediction.The optimized process achieved a deposition rate of 6257 mm3/min,with effective width and average layer height maintained at 10.1 mm and 4.13 mm,respectively.Microstructural optimization produced a fine,uniform,fully equiaxed grain structure with an average grain size of 38μm.These findings underscore the significant industrial potential of intelligent optimization strategies in WAAM for manufacturing lightweight,high-performance components in aerospace and transportation sectors.
基金funded by the National Natural Science Foundation of China Youth Fund(Grant No.62304022)Science and Technology on Electromechanical Dynamic Control Laboratory(China,Grant No.6142601012304)the 2022e2024 China Association for Science and Technology Innovation Integration Association Youth Talent Support Project(Grant No.2022QNRC001).
文摘Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.
文摘The integration of artificial intelligence into the development and production of mechatronic products offers a substantial opportunity to enhance efficiency, adaptability, and system performance. This paper examines the utilization of reinforcement learning as a control strategy, with a particular focus on its deployment in pivotal stages of the product development lifecycle, specifically between system architecture and system integration and verification. A controller based on reinforcement learning was developed and evaluated in comparison to traditional proportional-integral controllers in dynamic and fault-prone environments. The results illustrate the superior adaptability, stability, and optimization potential of the reinforcement learning approach, particularly in addressing dynamic disturbances and ensuring robust performance. The study illustrates how reinforcement learning can facilitate the transition from conceptual design to implementation by automating optimization processes, enabling interface automation, and enhancing system-level testing. Based on the aforementioned findings, this paper presents future directions for research, which include the integration of domain-specific knowledge into the reinforcement learning process and the validation of this process in real-world environments. The results underscore the potential of artificial intelligence-driven methodologies to revolutionize the design and deployment of intelligent mechatronic systems.
基金Yannick Ureel and Maarten Dobbelaere acknowledge financial support from the Fund for Scientific Research Flanders(FWO Flanders)respectively through doctoral fellowship grants(1185822N and 1S45522N)The authors acknowledge funding from the European Research Council under the European Union’s Horizon 2020 research and innovation programme/ERC(818607).
文摘1.Colors of chemical reaction engineering models Kinetic models of chemical reactions are a crucial asset for understanding and optimizing chemical processes[1].These models are critical for reactor design,process optimization,catalyst design,scale-up,and process control,making them indispensable in the chemical industry.Kinetic models predict the change in temperature and concentration of the relevant species,given an actual concentration and temperature.Reaction predictions are made by integrating the kinetic model with a reactor model,which accounts for external constraints,such as flow,inlet concentration。
文摘Fiber quality measurement in spinning preparation is crucial for optimizing waste and meeting yarn quality specifications.The brand-new Uster AFIS 6–the next-generation laboratory instrument from Uster Technologies–uniquely tests man-made fiber properties in addition to cotton.It provides critical data to optimize fiber process control for cotton,man-made fibers,and blended yarns.
文摘Objective:To investigate the application effects of intelligent guidance systems in optimizing health check-up process management.Methods:A total of 400 examinees who underwent physical examinations at the hospital’s Health Management Center from January to December 2024 were randomly divided into a control group(200 cases)and an observation group(200 cases).The control group used traditional manual guidance methods,while the observation group employed the intelligent guidance system.The study compared two groups in terms of completion time,waiting time for each procedure,check-up efficiency scores,examinee satisfaction,and report issuance time.Results:The overall examination time in the observation group(85.3±12.7 minutes)was significantly shorter than that in the control group(142.6±18.5 minutes)(P<0.01);average waiting time per procedure decreased by 62.4%;check-up efficiency scores(8.9±0.8 points)were significantly higher than those in the control group(5.2±1.1 points)(P<0.01);satisfaction reached 96.5%,significantly higher than the control group’s 78.0%(P<0.01);and report issuance time was advanced by 1.5 days.Conclusion:Intelligent guidance systems can significantly optimize check-up processes,improve work efficiency,and examinee satisfaction,demonstrating significant clinical application value.
基金Supported by the Funds from Central Government for Guiding Local Science and Technology Development(ZY20230102)Planning Project of Scientific Research and Technology Development in Guilin(20220104-4,20210202-1)Science and Technology Planing Project of Guangxi(Guike AB24010263).
文摘The latest progress in the process optimization and stability improvement of third-generation cephalosporins in recent years was reviewed.The introduction of green chemistry,enzyme catalysis,nanotechnology,lyophilization,and nitrogen-filled packaging technologies can only improve production efficiency and reduce the generation of by-products,but also significantly extend the shelf life of drugs.In the future,process automation and intelligent technology will further optimize the large-scale production process,and the combination of nanotechnology and precision drug delivery will promote the improvement of effect in clinical applications.
文摘Diaphragma juglandis(D.juglandis)Fructus is a brownish lamellar structure located between walnut kernels.As a traditional Chinese herbal medicine,it exhibits therapeutic effects including spleen-strengthening,kidney consolidation,astringency,diuresis,and heat-clearing.In this study,the polyphenolic constituents of D.juglandis and its functional instant tea were investigated in this study.Three polyphenolic compounds were isolated from 70%ethanol extract of D.juglandis Fructus as 2-methoxy juglone,regiolone and quercetin.The HPLC method was established for determination of the content of quercetin in the instant tea samples under the premise that the methodology was verifi ed to meet the standard requirements.The preparation process of D.juglandis Fructus instant tea was optimized through single factor experiments and Box-Behnken design-response surface methodology and the optimal conditions were determined as follows:feed rate of 10 mL/min,inlet temperature of 151℃,andβ-cyclodextrin addition of 9%.Then the antioxidant activity of each sample was evaluated using DPPH and ABTS radical scavenging assays.The results showed that the quercetin had significant antioxidant activity.The instant tea group demonstrated superior antioxidant effects compared to the extracts group at 50,200,and 800μg/mL(P<0.001),likely due to the optimized spray-drying process,which might have enhanced the solubility,stability,and bioavailability of the active compounds.The results provided critical foundational data for the deep processing and comprehensive utilization of D.juglandis Fructus.
基金supported by the National Key Research and Development Program of China(No.2020YFC1908702)the National Natural Science Foundation of China(No.52131002)+1 种基金the Science and Technology Commission of Shanghai Municipality(No.22dz1209200)China Three Gorges Corporation(No.202403018).
文摘High ammonia-nitrogen digestate has become a key bottleneck limiting the anaerobic digestion of organic solid waste.Vacuum ammonia stripping can simultaneously remove and recover ammonia nitrogen,which has attracted a lot of attention in recent years.To investigate the parameter effects on the efficiency and mass transfer,five combination conditions(53℃ 15 kPa,60°C 20 kPa,65°C 25 kPa,72°C 35 kPa,and 81°C 50 kPa)were conducted for ammonia stripping of sludge digestate.The results showed that 80%of ammonia nitrogen was stripped in 45 min for all experimental groups,but the ammonia transfer coefficient varied under different conditions,which increased with the rising of boiling point temperature,and reached the maximum value(39.0 mm/hr)at 81°C 50 kPa.The ammonia nitrogen removal efficiency was more than 80%for 30 min vacuum stripping after adjusting the initial pH to above 9.5,and adjustment of the initial alkalinity also affects the pH value of liquid digestate.It was found that pH and alkalinity are the key factors influencing the ammonia nitrogen dissociation and removal efficiency,while temperature and vacuum mainly affect the ammonia nitrogen mass transfer and removal velocity.In terms of the mechanism of vacuum ammonia stripping,it underwent alkalinity destruction,pH enhancement,ammonia nitrogen dissociation,and free ammonia removal.In this study,two-stage experiments of alkalinity destruction and ammonia removal were also carried out,which showed that the two-stage configuration was beneficial for ammonia removal.It provides a theoretical basis and practical technology for the vacuum ammonia stripping from liquid digestate of organic solid waste.
