The optimal condition for a one-step process removing organic compounds from coking wastewater by simultaneously synthesized organobentonite as a pretreatment was investigated.Results showed that sorption of organic c...The optimal condition for a one-step process removing organic compounds from coking wastewater by simultaneously synthesized organobentonite as a pretreatment was investigated.Results showed that sorption of organic compounds by organobentonite was positively correlated to the cation surfactant exchange on the bentonite and the octanol-water partition coefficient（Kow） of the solutes.With 0.75 g/L bentonite and 180 mg/L（60% of bentonite cation exchange capacity） cetyltrimethylammonium bromide,the removal efficiencies of the 16 polycyclic aromatic hydrocarbon（PAHs） specified by the US Environmental Protection Agency in coking wastewater except naphthalene were more than 90%,and that of benzo（a）pyrene was 99.5%.At the same time,the removal efficiencies of CODCr,NH3-N,volatile phenols,colour and turbidity were 28.6%,13.2%,8.9%,55% and 84.3%,respectively,and the ratio of BOD5/CODCr increased from 0.31 to 0.41.These results indicated that the one-step process had high removal efficiency for toxic and refractory hydrophobic organic compounds,and could improve the biodegradability of the coking wastewater.Therefore it could be a promising technology for the pretreatment of toxic and refractory organic wastewater.展开更多
Calcium carboaluminate was successfully prepared by a simple and efficient one-step method,and the effects of temperature,time,raw material ratio,carbonate type and heavy CaCO_(3)particle size on the products were inv...Calcium carboaluminate was successfully prepared by a simple and efficient one-step method,and the effects of temperature,time,raw material ratio,carbonate type and heavy CaCO_(3)particle size on the products were investigated in detail.The results show that increasing the temperature and extending the reaction time can enhance the yield and crystallisation degree of calcium carboaluminate.The proportion of Ca(OH)_(2),Al(OH)_(3)and CaCO_(3)is a pivotal factor in the synthesis of calcium carboaluminate.When the ratio of Ca(OH)_(2),Al(OH)_(3)and CaCO_(3)is 3:2:1,the diffraction peaks of calcium carboaluminate in the products are relatively sharp and strong.Furthermore,the purity and crystallinity of the synthesized calcium carboaluminate are higher when heavy CaCO_(3)with the particle size of 120 mesh is used as the carbonate raw material,in comparison to CO_(2),Na_(2)CO_(3)and light CaCO_(3).As results,a simple and efficient method for the synthesis of calcium carboaluminate is proposed,which will provide a solid experimental foundation and technical support for the industrial application of calcium carboaluminate in marine concrete.展开更多
一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家...一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家赫拉克利特所说的“万物流转”,又说“你不能两次踏进同一条河流,因为新的水不断地流过你的身旁”,他所表达的意思是“世界上唯一不变的就是变化”。展开更多
Building a superhydrophobic coating on a carbon steel substrate is an effective strategy for enhancing metal protection.A practical approach to producing a series of superhydrophobic Ni/SiO_(2)composite coatings(SSN)u...Building a superhydrophobic coating on a carbon steel substrate is an effective strategy for enhancing metal protection.A practical approach to producing a series of superhydrophobic Ni/SiO_(2)composite coatings(SSN)using one-step electrodeposition method is shown.The effect of processing parameters on surface structure and wettability was thoroughly explored,resulting in the identification of three typical surface morphologies.The prepared coating with petal-like structure(SSN-3)obtained under the optimum parameters exhibited the best water repellency,achieving a contact angle of 162.7°and a sliding angle of 4.1°.The droplet bouncing behavior on SSN coatings surface was studied,and the delayed icing time was recorded.Meanwhile,the mechanical stability and chemical corrosion resistance of SSN coatings were focused.The superhydrophobic SSN-3 coating with unique surface structure exhibited excellent reliability.The anticorrosion mechanism of SSN-3 coating was discussed,and its corrosion protection efficiency was up to 98.5%.The superior properties of the superhydrophobic SSN-3 coating make it suitable for diverse applications.展开更多
Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim ...Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim to offer a platform for the rapid dissemination of significant,novel,and high-impact research in the fields of agricultural product processing science,technology,engineering,and nutrition.Additionally,supplemental issues are curated and published to facilitate in-depth discussions on special topics.展开更多
The in-flight heating process of cerium dioxide(CeO_(2))powders was investigated through experiments and numerical simulations.In the experiment,CeO_(2)powder(average size of 30μm)was injected into radio-frequency(RF...The in-flight heating process of cerium dioxide(CeO_(2))powders was investigated through experiments and numerical simulations.In the experiment,CeO_(2)powder(average size of 30μm)was injected into radio-frequency(RF)argon plasma,and the temperatures were measured using a DPV-2000 monitor.A model combining the electromagnetism,thermal flow,and heat transfer characteristics of powder during in-flight heating in argon plasma was proposed.The melting processes of CeO_(2)powders of different diameters,with and without thermal resistance effect,were investigated.Results show that the heating process of CeO_(2)powder particles consists of three main stages,one of which is relevant to a dimensionless parameter known as the Biot number.When the Biot value≥0.1,thermal resistance increases significantly,especially for the larger powders.The predicted temperature of the particles at the outlet(1800–2880 K)is in good agreement with the experimental result.展开更多
The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from...The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).展开更多
The three-dimensional(3D) Pd-based nanoflower structures,assembled from two-dimensional(2D)nanosheets,are characterized by their stable and ordered configurations.These structures have been extensively designed as ano...The three-dimensional(3D) Pd-based nanoflower structures,assembled from two-dimensional(2D)nanosheets,are characterized by their stable and ordered configurations.These structures have been extensively designed as anode materials for fuel cells.However,the exploration of trimetallic nanoflowers with porous architectures remains limited.In this study,we present a straightforward one-step solvothermal method for the synthesis of trimetallic Pd Cu Ni porous nanoflowers(PNFs).Leveraging several unique advantages,such as an open superstructure,high porosity,and enhanced electronic interactions among the trimetals,the resulting Pd Cu Ni PNFs demonstrate significantly improved electrochemical performance,with mass activities reaching 5.94 and 10.14 A/mg for the ethanol oxidation reaction(EOR)and the ethylene glycol oxidation reaction(EGOR),respectively.Furthermore,the Pd Cu Ni PNFs exhibit optimized d-band centers and the most negative onset oxidation potential,indicating enhanced antitoxicity and stability.This study not only provides a novel perspective on the synthesis of 3D porous nanomaterials but also highlights the potential application value of trimetallic nanoalloys in catalysis.展开更多
Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim ...Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim to offer a platform for the rapid dissemination of signifi cant,novel,and high-impact research in the fi elds of agricultural product processing science,technology,engineering,and nutrition.Additionally,supplemental issues are curated and published to facilitate in-depth discussions on special topics.展开更多
Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durabili...Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durability,and corrosion resistance.These metals have body-centered cubic crystal structure,characterized by limited slip systems and impeded dislocation motion,resulting in significant low-temperature brittleness,which poses challenges for the conventional processing.Additive manufacturing technique provides an innovative approach,enabling the production of intricate parts without molds,which significantly improves the efficiency of material usage.This review provides a comprehensive overview of the advancements in additive manufacturing techniques for the production of refractory metals,such as W,Ta,Mo,and Nb,particularly the laser powder bed fusion.In this review,the influence mechanisms of key process parameters(laser power,scan strategy,and powder characteristics)on the evolution of material microstructure,the formation of metallurgical defects,and mechanical properties were discussed.Generally,optimizing powder characteristics,such as sphericity,implementing substrate preheating,and formulating alloying strategies can significantly improve the densification and crack resistance of manufactured parts.Meanwhile,strictly controlling the oxygen impurity content and optimizing the energy density input are also the key factors to achieve the simultaneous improvement in strength and ductility of refractory metals.Although additive manufacturing technique provides an innovative solution for processing refractory metals,critical issues,such as residual stress control,microstructure and performance anisotropy,and process stability,still need to be addressed.This review not only provides a theoretical basis for the additive manufacturing of high-performance refractory metals,but also proposes forward-looking directions for their industrial application.展开更多
Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
Processes supported by process-aware information systems are subject to continuous and often subtle changes due to evolving operational,organizational,or regulatory factors.These changes,referred to as incremental con...Processes supported by process-aware information systems are subject to continuous and often subtle changes due to evolving operational,organizational,or regulatory factors.These changes,referred to as incremental concept drift,gradually alter the behavior or structure of processes,making their detection and localization a challenging task.Traditional process mining techniques frequently assume process stationarity and are limited in their ability to detect such drift,particularly from a control-flow perspective.The objective of this research is to develop an interpretable and robust framework capable of detecting and localizing incremental concept drift in event logs,with a specific emphasis on the structural evolution of control-flow semantics in processes.We propose DriftXMiner,a control-flow-aware hybrid framework that combines statistical,machine learning,and process model analysis techniques.The approach comprises three key components:(1)Cumulative Drift Scanner that tracks directional statistical deviations to detect early drift signals;(2)a Temporal Clustering and Drift-Aware Forest Ensemble(DAFE)to capture distributional and classification-level changes in process behavior;and(3)Petri net-based process model reconstruction,which enables the precise localization of structural drift using transition deviation metrics and replay fitness scores.Experimental validation on the BPI Challenge 2017 event log demonstrates that DriftXMiner effectively identifies and localizes gradual and incremental process drift over time.The framework achieves a detection accuracy of 92.5%,a localization precision of 90.3%,and an F1-score of 0.91,outperforming competitive baselines such as CUSUM+Histograms and ADWIN+Alpha Miner.Visual analyses further confirm that identified drift points align with transitions in control-flow models and behavioral cluster structures.DriftXMiner offers a novel and interpretable solution for incremental concept drift detection and localization in dynamic,process-aware systems.By integrating statistical signal accumulation,temporal behavior profiling,and structural process mining,the framework enables finegrained drift explanation and supports adaptive process intelligence in evolving environments.Its modular architecture supports extension to streaming data and real-time monitoring contexts.展开更多
This study investigated the effects of xu-argument-based continuation writing on learners’processing of source texts.Seventy-five participants were randomly assigned to three conditions:(1)continuation writing,(2)sum...This study investigated the effects of xu-argument-based continuation writing on learners’processing of source texts.Seventy-five participants were randomly assigned to three conditions:(1)continuation writing,(2)summary writing,or(3)reading comprehension.Eye-tracking data were collected during reading,measuring early(first fixation duration,first pass duration)and late(go-past time,total fixation duration)eye movements.During writing,source-text rereading was tracked via fixation counts and durations.Results showed that task type did not affect initial lexical access,as first fixation duration showed no group differences.However,both production groups exhibited significantly longer first pass durations than the reading comprehension group.Late measures revealed a gradient pattern:the continuation writing group spent significantly longer gopast time and total fixation duration than the summary writing group,which exceeded the reading comprehension group.This indicates that continuation tasks promoted deeper cognitive engagement during reading.During writing,the continuation writing group spent more time rereading the source text with higher fixation counts than the summary writing group.These findings suggest that continuation writing triggers more intensive reader-text interaction during pre-writing and enhances comprehension-production coupling through sustained attention to input during writing.This study sheds light on the cognitive mechanisms underlying the theoretical and pedagogical value of xu-argument.展开更多
The aging process is an inexorable fact throughout our lives and is considered a major factor in develo ping neurological dysfunctions associated with cognitive,emotional,and motor impairments.Aging-associated neurode...The aging process is an inexorable fact throughout our lives and is considered a major factor in develo ping neurological dysfunctions associated with cognitive,emotional,and motor impairments.Aging-associated neurodegenerative diseases are characterized by the progressive loss of neuronal structure and function.展开更多
Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLD...Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLDPEs)with comparable molecular weights but different short-chain branch(SCB)contents(ranging of 5-66 per 1000 carbon atoms)were modified via dynamic melt mixing using 2 wt% benzoyl peroxide at 145℃ and 50 r/min for 30 min.The influence of SCB content on the processability and structure of the resulting products was systematically investigated.All modified products exhibited good melt processability with melt flow rates(MFR)ranging from 0.46 g/10min to 1.07 g/10min.Products derived from low-SCB LLDPEs showed a lower MFR,higher cross-linking content,a larger number of long-chain branches,and a higher degree of benzoyl grafting.In contrast,those produced from high-SCB LLDPEs exhibited improved processability,reduced cross-linking,fewer long-chain branches,and lower benzoyl grafting levels.A detailed structural investigation of the soluble and insoluble fractions,which were separated using trichlorobenzene fractionation,was conducted to analyze the structural features of various modified products and demonstrate that the SCB content(i.e.,tertiary carbon density)significantly influences radical coupling during dynamic modification.Elevated tertiary carbon density,by introducing greater steric hindrance,suppresses radical coupling during dynamic modification,thereby reducing the efficiency of both crosslinking and peroxide fragment grafting.These findings provide new insights into the structure-reactivity relationships in peroxide-induced polyethylene modification and lay the foundation for tailoring material properties via dynamic processing.展开更多
Business Process Modelling(BPM)is essential for analyzing,improving,and automating the flow of information within organizations,but traditional approaches based on manual interpretation are slow,error-prone,and requir...Business Process Modelling(BPM)is essential for analyzing,improving,and automating the flow of information within organizations,but traditional approaches based on manual interpretation are slow,error-prone,and require a high level of expertise.This article proposes an innovative alternative solution that overcomes these limitations by automatically generating comprehensive Business Process Modelling and Notation(BPMN)diagrams solely from verbal descriptions of the processes to be modeled,utilizing Large Language Models(LLMs)and multimodal Artificial Intelligence(AI).Experimental results,based on video recordings of process explanations provided by an expert from an organization(in this case,the Commercial Courts of a public justice administration),demonstrate that the proposed methodology successfully enables the automatic generation of complete and accurate BPMN diagrams,leading to significant improvements in the speed,accuracy,and accessibility of process modeling.This research makes a substantial contribution to the field of business process modeling,as its methodology is groundbreaking in its use of LLMs and multimodal AI capabilities to handle different types of source material(text and video),combining several tools to minimize the number of queries and reduce the complexity of the prompts required for the automatic generation of successful BPMN diagrams.展开更多
The complexity of the seismicity pattern for the subduction zone along the oceanic plate triggered the outer rise events and revealed cyclic tectonic deformation conditions along the plate subduction zones.The outer r...The complexity of the seismicity pattern for the subduction zone along the oceanic plate triggered the outer rise events and revealed cyclic tectonic deformation conditions along the plate subduction zones.The outer rise earthquakes have been observed along the Sunda arc,following the estimated rupture area of the 2005 M_(W)8.6 Nias earthquakes.Here,we used kinematic waveform inversion(KIWI)to obtain the source parameters of the 14 May 2021 M_(W)6.6 event off the west coast of northern Sumatra and to define the fault plane that triggered this outer rise event.The KIWI algorithm allows two types of seismic source to be configured:the moment tensor model to describe the type of shear with six moment tensor components and the Eikonal model for the rupture of pure double-couple sources.This method was chosen for its flexibility to be applied for different sources of seismicity and also for the automated full-moment tensor solution with real-time monitoring.We used full waveform traces from 8 broadband seismic stations within 1000 km epicentral distances sourced from the Incorporated Research Institutions for Seismology(IRIS-IDA)and Geofon GFZ seismic record databases.The initial origin time and hypocenter values are obtained from the IRIS-IDA.The synthetic seismograms used in the inversion process are based on the existing regional green function database model and were accessed from the KIWI Tools Green's Function Database.The obtained scalar seismic moment value is 1.18×10^(19)N·m,equivalent to a moment magnitude M_(W)6.6.The source parameters are 140°,44°,and−99°for the strike,dip,and rake values at a centroid depth of 10.2 km,indicating that this event is a normal fault earthquake that occurred in the outer rise area.The outer rise events with normal faults typically occur at the shallow part of the plate,with nodal-plane dips predominantly in the range of 30°-60°on the weak oceanic lithosphere due to hydrothermal alteration.The stress regime around the plate subduction zone varies both temporally and spatially due to the cyclic influences of megathrust earthquakes.Tensional outer rise earthquakes tend to occur after the megathrust events.The relative timing of these events is not known due to the viscous relaxation of the down going slab and poroelastic response in the trench slope region.The occurrence of the 14 May 2021 earthquake shows the seismicity in the outer rise region in the strongly coupled Sunda arc subduction zone due to elastic bending stress within the duration of the seismic cycle.展开更多
In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A fi...In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A finite element model of the plastic-lined composite hydrogen storage cylinder,designed to withstand a working pressure of 70.0 MPa,was established by using the wound composite modeler(WCM)in the Abaqus software to analyze the forces acting on the winding layer.The Hashin failure criterion was utilized as the standard for assessing composite failure,and a progressive failure analysis of the cylinder was conducted to predict both the bursting pressure and the failure location of the composite hydrogen storage cylinder.The results indicate that the reaming process can effectively reduce the maximum filament winding thickness in the head section and promote a more uniform transition.At the bursting pressure,the stress within the head liner decreases,thereby enhancing the ultimate bearing capacity of the cylinder.A control system for a four-axis winding machine was designed by utilizing an industrial computer and a programmable multi-axis controller(PMAC).The winding line pattern is designed and the G-code trajectory is generated by the industrial computer.The numerical control system,composed of the PMAC and servo motor,executes the four-axis interpolation motion.展开更多
To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt b...To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt by physical property index,microscopic morphology,rheological testing,and infrared spectroscopy on multiple scales.The results show that the best preparation process for TB-modified asphalt is stirring at 260℃ for 4 h at 400 rpm,which significantly reduces the modification time of the asphalt.From a physical property viewpoint,the TB composite-modified asphalt sample with 5% styrene-butadiene-styrene(SBS)+1% aromatics+0.1% sulfur exhibits high-comprehensive,high-and low-temperature properties.More-over,its crosslinked mesh structure comprises black rubber particles uniformly interwoven in the middle,which further enhances the performance of the asphalt and results in an excellent performance formulation.In addition,the sample with 5%SBS content has a higher G*value and smaller δ value than that with 3%SBS content,indicating that its high-temperature resistance is improved.The effect of adding 3%SBS content on the viscoelastic ratio is,to some extent,less than that caused by 20% rubber powder.展开更多
Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentrat...Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.展开更多
基金supported by the National Natural Science Foundation of China (No. 20890111)
文摘The optimal condition for a one-step process removing organic compounds from coking wastewater by simultaneously synthesized organobentonite as a pretreatment was investigated.Results showed that sorption of organic compounds by organobentonite was positively correlated to the cation surfactant exchange on the bentonite and the octanol-water partition coefficient（Kow） of the solutes.With 0.75 g/L bentonite and 180 mg/L（60% of bentonite cation exchange capacity） cetyltrimethylammonium bromide,the removal efficiencies of the 16 polycyclic aromatic hydrocarbon（PAHs） specified by the US Environmental Protection Agency in coking wastewater except naphthalene were more than 90%,and that of benzo（a）pyrene was 99.5%.At the same time,the removal efficiencies of CODCr,NH3-N,volatile phenols,colour and turbidity were 28.6%,13.2%,8.9%,55% and 84.3%,respectively,and the ratio of BOD5/CODCr increased from 0.31 to 0.41.These results indicated that the one-step process had high removal efficiency for toxic and refractory hydrophobic organic compounds,and could improve the biodegradability of the coking wastewater.Therefore it could be a promising technology for the pretreatment of toxic and refractory organic wastewater.
基金Funded by the National Nature Science Foundation of China(No.52078321)。
文摘Calcium carboaluminate was successfully prepared by a simple and efficient one-step method,and the effects of temperature,time,raw material ratio,carbonate type and heavy CaCO_(3)particle size on the products were investigated in detail.The results show that increasing the temperature and extending the reaction time can enhance the yield and crystallisation degree of calcium carboaluminate.The proportion of Ca(OH)_(2),Al(OH)_(3)and CaCO_(3)is a pivotal factor in the synthesis of calcium carboaluminate.When the ratio of Ca(OH)_(2),Al(OH)_(3)and CaCO_(3)is 3:2:1,the diffraction peaks of calcium carboaluminate in the products are relatively sharp and strong.Furthermore,the purity and crystallinity of the synthesized calcium carboaluminate are higher when heavy CaCO_(3)with the particle size of 120 mesh is used as the carbonate raw material,in comparison to CO_(2),Na_(2)CO_(3)and light CaCO_(3).As results,a simple and efficient method for the synthesis of calcium carboaluminate is proposed,which will provide a solid experimental foundation and technical support for the industrial application of calcium carboaluminate in marine concrete.
文摘一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家赫拉克利特所说的“万物流转”,又说“你不能两次踏进同一条河流,因为新的水不断地流过你的身旁”,他所表达的意思是“世界上唯一不变的就是变化”。
基金the Natural Science Foundation of Chongqing of China(Nos.CSTB2024NSCQ-MSX1013 and cstc2021jcyj-msxmX1139)the Science and Technology Research Program of Chongqing Education Commission(Nos.KJZD-K202304502,KJQN202201214,KJQN202001243 and KJZD-M202301201)the Opening Project of Material Corrosion and Protection Key Laboratory of Sichuan province(No.2024CL05).
文摘Building a superhydrophobic coating on a carbon steel substrate is an effective strategy for enhancing metal protection.A practical approach to producing a series of superhydrophobic Ni/SiO_(2)composite coatings(SSN)using one-step electrodeposition method is shown.The effect of processing parameters on surface structure and wettability was thoroughly explored,resulting in the identification of three typical surface morphologies.The prepared coating with petal-like structure(SSN-3)obtained under the optimum parameters exhibited the best water repellency,achieving a contact angle of 162.7°and a sliding angle of 4.1°.The droplet bouncing behavior on SSN coatings surface was studied,and the delayed icing time was recorded.Meanwhile,the mechanical stability and chemical corrosion resistance of SSN coatings were focused.The superhydrophobic SSN-3 coating with unique surface structure exhibited excellent reliability.The anticorrosion mechanism of SSN-3 coating was discussed,and its corrosion protection efficiency was up to 98.5%.The superior properties of the superhydrophobic SSN-3 coating make it suitable for diverse applications.
文摘Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim to offer a platform for the rapid dissemination of significant,novel,and high-impact research in the fields of agricultural product processing science,technology,engineering,and nutrition.Additionally,supplemental issues are curated and published to facilitate in-depth discussions on special topics.
基金National Natural Science Foundation of China(11875039)Shanxi Scholarship Council of China(2023-033)+2 种基金Fundamental Research Program of Shanxi Province(202303021221071)China Baowu Low Carbon Metallurgical Innovation Foundation(2022)2023 Anhui Major Industrial Innovation Plan Project。
文摘The in-flight heating process of cerium dioxide(CeO_(2))powders was investigated through experiments and numerical simulations.In the experiment,CeO_(2)powder(average size of 30μm)was injected into radio-frequency(RF)argon plasma,and the temperatures were measured using a DPV-2000 monitor.A model combining the electromagnetism,thermal flow,and heat transfer characteristics of powder during in-flight heating in argon plasma was proposed.The melting processes of CeO_(2)powders of different diameters,with and without thermal resistance effect,were investigated.Results show that the heating process of CeO_(2)powder particles consists of three main stages,one of which is relevant to a dimensionless parameter known as the Biot number.When the Biot value≥0.1,thermal resistance increases significantly,especially for the larger powders.The predicted temperature of the particles at the outlet(1800–2880 K)is in good agreement with the experimental result.
基金Sichuan Science and Technology Program(2025ZNSFSC1341)Fundamental Research Funds for the Central Universities(J2022-090,25CAFUC04087)。
文摘The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).
基金supported by the National Natural Science Foundation of China (No.52274304)。
文摘The three-dimensional(3D) Pd-based nanoflower structures,assembled from two-dimensional(2D)nanosheets,are characterized by their stable and ordered configurations.These structures have been extensively designed as anode materials for fuel cells.However,the exploration of trimetallic nanoflowers with porous architectures remains limited.In this study,we present a straightforward one-step solvothermal method for the synthesis of trimetallic Pd Cu Ni porous nanoflowers(PNFs).Leveraging several unique advantages,such as an open superstructure,high porosity,and enhanced electronic interactions among the trimetals,the resulting Pd Cu Ni PNFs demonstrate significantly improved electrochemical performance,with mass activities reaching 5.94 and 10.14 A/mg for the ethanol oxidation reaction(EOR)and the ethylene glycol oxidation reaction(EGOR),respectively.Furthermore,the Pd Cu Ni PNFs exhibit optimized d-band centers and the most negative onset oxidation potential,indicating enhanced antitoxicity and stability.This study not only provides a novel perspective on the synthesis of 3D porous nanomaterials but also highlights the potential application value of trimetallic nanoalloys in catalysis.
文摘Agricultural Products Processing and Storage(ISSN 3059-4510,Owner:Hunan Academy of Agricultural Sciences,China.Production and hosting:Springer Nature)is an international,peer-reviewed open access journal with the aim to offer a platform for the rapid dissemination of signifi cant,novel,and high-impact research in the fi elds of agricultural product processing science,technology,engineering,and nutrition.Additionally,supplemental issues are curated and published to facilitate in-depth discussions on special topics.
基金National MCF Energy R&D Program(2024YFE03260300)。
文摘Refractory metals,including tungsten(W),tantalum(Ta),molybdenum(Mo),and niobium(Nb),play a vital role in industries,such as nuclear energy and aerospace,owing to their exceptional melting temperatures,thermal durability,and corrosion resistance.These metals have body-centered cubic crystal structure,characterized by limited slip systems and impeded dislocation motion,resulting in significant low-temperature brittleness,which poses challenges for the conventional processing.Additive manufacturing technique provides an innovative approach,enabling the production of intricate parts without molds,which significantly improves the efficiency of material usage.This review provides a comprehensive overview of the advancements in additive manufacturing techniques for the production of refractory metals,such as W,Ta,Mo,and Nb,particularly the laser powder bed fusion.In this review,the influence mechanisms of key process parameters(laser power,scan strategy,and powder characteristics)on the evolution of material microstructure,the formation of metallurgical defects,and mechanical properties were discussed.Generally,optimizing powder characteristics,such as sphericity,implementing substrate preheating,and formulating alloying strategies can significantly improve the densification and crack resistance of manufactured parts.Meanwhile,strictly controlling the oxygen impurity content and optimizing the energy density input are also the key factors to achieve the simultaneous improvement in strength and ductility of refractory metals.Although additive manufacturing technique provides an innovative solution for processing refractory metals,critical issues,such as residual stress control,microstructure and performance anisotropy,and process stability,still need to be addressed.This review not only provides a theoretical basis for the additive manufacturing of high-performance refractory metals,but also proposes forward-looking directions for their industrial application.
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
文摘Processes supported by process-aware information systems are subject to continuous and often subtle changes due to evolving operational,organizational,or regulatory factors.These changes,referred to as incremental concept drift,gradually alter the behavior or structure of processes,making their detection and localization a challenging task.Traditional process mining techniques frequently assume process stationarity and are limited in their ability to detect such drift,particularly from a control-flow perspective.The objective of this research is to develop an interpretable and robust framework capable of detecting and localizing incremental concept drift in event logs,with a specific emphasis on the structural evolution of control-flow semantics in processes.We propose DriftXMiner,a control-flow-aware hybrid framework that combines statistical,machine learning,and process model analysis techniques.The approach comprises three key components:(1)Cumulative Drift Scanner that tracks directional statistical deviations to detect early drift signals;(2)a Temporal Clustering and Drift-Aware Forest Ensemble(DAFE)to capture distributional and classification-level changes in process behavior;and(3)Petri net-based process model reconstruction,which enables the precise localization of structural drift using transition deviation metrics and replay fitness scores.Experimental validation on the BPI Challenge 2017 event log demonstrates that DriftXMiner effectively identifies and localizes gradual and incremental process drift over time.The framework achieves a detection accuracy of 92.5%,a localization precision of 90.3%,and an F1-score of 0.91,outperforming competitive baselines such as CUSUM+Histograms and ADWIN+Alpha Miner.Visual analyses further confirm that identified drift points align with transitions in control-flow models and behavioral cluster structures.DriftXMiner offers a novel and interpretable solution for incremental concept drift detection and localization in dynamic,process-aware systems.By integrating statistical signal accumulation,temporal behavior profiling,and structural process mining,the framework enables finegrained drift explanation and supports adaptive process intelligence in evolving environments.Its modular architecture supports extension to streaming data and real-time monitoring contexts.
文摘This study investigated the effects of xu-argument-based continuation writing on learners’processing of source texts.Seventy-five participants were randomly assigned to three conditions:(1)continuation writing,(2)summary writing,or(3)reading comprehension.Eye-tracking data were collected during reading,measuring early(first fixation duration,first pass duration)and late(go-past time,total fixation duration)eye movements.During writing,source-text rereading was tracked via fixation counts and durations.Results showed that task type did not affect initial lexical access,as first fixation duration showed no group differences.However,both production groups exhibited significantly longer first pass durations than the reading comprehension group.Late measures revealed a gradient pattern:the continuation writing group spent significantly longer gopast time and total fixation duration than the summary writing group,which exceeded the reading comprehension group.This indicates that continuation tasks promoted deeper cognitive engagement during reading.During writing,the continuation writing group spent more time rereading the source text with higher fixation counts than the summary writing group.These findings suggest that continuation writing triggers more intensive reader-text interaction during pre-writing and enhances comprehension-production coupling through sustained attention to input during writing.This study sheds light on the cognitive mechanisms underlying the theoretical and pedagogical value of xu-argument.
文摘The aging process is an inexorable fact throughout our lives and is considered a major factor in develo ping neurological dysfunctions associated with cognitive,emotional,and motor impairments.Aging-associated neurodegenerative diseases are characterized by the progressive loss of neuronal structure and function.
基金financially supported by the Science and Technology Project of PetroChina Company Limited,China(No.2022DJ6314)the National Natural Science Foundation of China(No.52173056)。
文摘Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLDPEs)with comparable molecular weights but different short-chain branch(SCB)contents(ranging of 5-66 per 1000 carbon atoms)were modified via dynamic melt mixing using 2 wt% benzoyl peroxide at 145℃ and 50 r/min for 30 min.The influence of SCB content on the processability and structure of the resulting products was systematically investigated.All modified products exhibited good melt processability with melt flow rates(MFR)ranging from 0.46 g/10min to 1.07 g/10min.Products derived from low-SCB LLDPEs showed a lower MFR,higher cross-linking content,a larger number of long-chain branches,and a higher degree of benzoyl grafting.In contrast,those produced from high-SCB LLDPEs exhibited improved processability,reduced cross-linking,fewer long-chain branches,and lower benzoyl grafting levels.A detailed structural investigation of the soluble and insoluble fractions,which were separated using trichlorobenzene fractionation,was conducted to analyze the structural features of various modified products and demonstrate that the SCB content(i.e.,tertiary carbon density)significantly influences radical coupling during dynamic modification.Elevated tertiary carbon density,by introducing greater steric hindrance,suppresses radical coupling during dynamic modification,thereby reducing the efficiency of both crosslinking and peroxide fragment grafting.These findings provide new insights into the structure-reactivity relationships in peroxide-induced polyethylene modification and lay the foundation for tailoring material properties via dynamic processing.
基金funded by Fundación CajaCanarias and Fundación Bancaria“la Caixa”,grant number 2023DIG11.
文摘Business Process Modelling(BPM)is essential for analyzing,improving,and automating the flow of information within organizations,but traditional approaches based on manual interpretation are slow,error-prone,and require a high level of expertise.This article proposes an innovative alternative solution that overcomes these limitations by automatically generating comprehensive Business Process Modelling and Notation(BPMN)diagrams solely from verbal descriptions of the processes to be modeled,utilizing Large Language Models(LLMs)and multimodal Artificial Intelligence(AI).Experimental results,based on video recordings of process explanations provided by an expert from an organization(in this case,the Commercial Courts of a public justice administration),demonstrate that the proposed methodology successfully enables the automatic generation of complete and accurate BPMN diagrams,leading to significant improvements in the speed,accuracy,and accessibility of process modeling.This research makes a substantial contribution to the field of business process modeling,as its methodology is groundbreaking in its use of LLMs and multimodal AI capabilities to handle different types of source material(text and video),combining several tools to minimize the number of queries and reduce the complexity of the prompts required for the automatic generation of successful BPMN diagrams.
基金supported by the National Natural Science Foundation of China(Grant No.42130312)。
文摘The complexity of the seismicity pattern for the subduction zone along the oceanic plate triggered the outer rise events and revealed cyclic tectonic deformation conditions along the plate subduction zones.The outer rise earthquakes have been observed along the Sunda arc,following the estimated rupture area of the 2005 M_(W)8.6 Nias earthquakes.Here,we used kinematic waveform inversion(KIWI)to obtain the source parameters of the 14 May 2021 M_(W)6.6 event off the west coast of northern Sumatra and to define the fault plane that triggered this outer rise event.The KIWI algorithm allows two types of seismic source to be configured:the moment tensor model to describe the type of shear with six moment tensor components and the Eikonal model for the rupture of pure double-couple sources.This method was chosen for its flexibility to be applied for different sources of seismicity and also for the automated full-moment tensor solution with real-time monitoring.We used full waveform traces from 8 broadband seismic stations within 1000 km epicentral distances sourced from the Incorporated Research Institutions for Seismology(IRIS-IDA)and Geofon GFZ seismic record databases.The initial origin time and hypocenter values are obtained from the IRIS-IDA.The synthetic seismograms used in the inversion process are based on the existing regional green function database model and were accessed from the KIWI Tools Green's Function Database.The obtained scalar seismic moment value is 1.18×10^(19)N·m,equivalent to a moment magnitude M_(W)6.6.The source parameters are 140°,44°,and−99°for the strike,dip,and rake values at a centroid depth of 10.2 km,indicating that this event is a normal fault earthquake that occurred in the outer rise area.The outer rise events with normal faults typically occur at the shallow part of the plate,with nodal-plane dips predominantly in the range of 30°-60°on the weak oceanic lithosphere due to hydrothermal alteration.The stress regime around the plate subduction zone varies both temporally and spatially due to the cyclic influences of megathrust earthquakes.Tensional outer rise earthquakes tend to occur after the megathrust events.The relative timing of these events is not known due to the viscous relaxation of the down going slab and poroelastic response in the trench slope region.The occurrence of the 14 May 2021 earthquake shows the seismicity in the outer rise region in the strongly coupled Sunda arc subduction zone due to elastic bending stress within the duration of the seismic cycle.
文摘In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A finite element model of the plastic-lined composite hydrogen storage cylinder,designed to withstand a working pressure of 70.0 MPa,was established by using the wound composite modeler(WCM)in the Abaqus software to analyze the forces acting on the winding layer.The Hashin failure criterion was utilized as the standard for assessing composite failure,and a progressive failure analysis of the cylinder was conducted to predict both the bursting pressure and the failure location of the composite hydrogen storage cylinder.The results indicate that the reaming process can effectively reduce the maximum filament winding thickness in the head section and promote a more uniform transition.At the bursting pressure,the stress within the head liner decreases,thereby enhancing the ultimate bearing capacity of the cylinder.A control system for a four-axis winding machine was designed by utilizing an industrial computer and a programmable multi-axis controller(PMAC).The winding line pattern is designed and the G-code trajectory is generated by the industrial computer.The numerical control system,composed of the PMAC and servo motor,executes the four-axis interpolation motion.
基金Funded by the National Natural Science Foundation of China(No.52278446)。
文摘To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt by physical property index,microscopic morphology,rheological testing,and infrared spectroscopy on multiple scales.The results show that the best preparation process for TB-modified asphalt is stirring at 260℃ for 4 h at 400 rpm,which significantly reduces the modification time of the asphalt.From a physical property viewpoint,the TB composite-modified asphalt sample with 5% styrene-butadiene-styrene(SBS)+1% aromatics+0.1% sulfur exhibits high-comprehensive,high-and low-temperature properties.More-over,its crosslinked mesh structure comprises black rubber particles uniformly interwoven in the middle,which further enhances the performance of the asphalt and results in an excellent performance formulation.In addition,the sample with 5%SBS content has a higher G*value and smaller δ value than that with 3%SBS content,indicating that its high-temperature resistance is improved.The effect of adding 3%SBS content on the viscoelastic ratio is,to some extent,less than that caused by 20% rubber powder.
基金supported by the National Key Research and Development Program of China(Grant No.2023YFB3710805).
文摘Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.
