Phenolic foams(PFs)as thermal insulation material with outstanding flame retardancy are required to match society’s ever-expanding safety expectations;however,a trade-off exists between flame retardancy and toughness...Phenolic foams(PFs)as thermal insulation material with outstanding flame retardancy are required to match society’s ever-expanding safety expectations;however,a trade-off exists between flame retardancy and toughness.Here,for the first time,we synthesized a novel reactive phosphorus-containing tung-oil-based derivative and used it to toughen PF,resulting in PFs with a combination of excellent mechanical properties and flame retardancy.Compared with pure PF,the modified PFs exhibit enhanced mechanical properties,with specific compressive and flexural strengths as high as 5.67 MPa and 12.46 MPa,which represent increases of 90.67%and 178.7%over those of pure PF,respectively.Meanwhile,the limiting oxygen index(LOI)values of the modified PFs are improved as much as 40.83%.Scanning electron microscopy micrographs show that the microstructure of the modified PFs is better than that of pure PF,with a more uniform cell morphology,a narrower pore size distribution range,and a smaller average pore size,all of which are beneficial to the foam’s mechanical properties.This study provides a scientific paradigm for the development of advanced PFs based on renewable biological resources.展开更多
The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel l...The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel logging method for detection of high-resistance formations in OBM using highfrequency electrodes. The method addresses the issue of shallow depth of investigation(DOI) in existing electrical logging instruments, while simultaneously ensuring the vertical resolution. Based on the principle of current continuity, the total impedance of the loop is obtained by equating the measurement loop to the series form of a capacitively coupled circuit. and its validity is verified in a homogeneous formation model and a radial two-layer formation model with a mud standoff. Then, the instrument operating frequency and electrode system parameters were preferentially determined by numerical simulation, and the effect of mud gap on impedance measurement was investigated. Subsequently, the DOI of the instrument was investigated utilizing the pseudo-geometric factor defined by the real part of impedance. It was determined that the detection depth of the instrument is 8.74 cm, while the effective vertical resolution was not less than 2 cm. Finally, a focused high-frequency electrode-type instrument was designed by introducing a pair of focused electrodes, which effectively enhanced the DOI of the instrument and was successfully deployed in the Oklahoma formation model. The simulation results demonstrate that the novel method can achieve a detection depth of 17.40 cm in highly-resistive formations drilling with OBM, which is approximately twice the depth of detection of the existing oil-based mud microimager instruments. Furthermore, its effective vertical resolution remains at or above 2 cm,which is comparable to the resolution of the existing OBM electrical logging instrument.展开更多
To address the issue of uneven temperature distribution in shale gas oil-based drill cuttings pyrolysis furnaces,a numerical model was developed using Fluent software.The effects of nitrogen flow rate,heating tube spa...To address the issue of uneven temperature distribution in shale gas oil-based drill cuttings pyrolysis furnaces,a numerical model was developed using Fluent software.The effects of nitrogen flow rate,heating tube spacing,and furnace dimensions on the internal temperature field were thoroughly analyzed from a mechanistic perspective.The results indicated that non-uniform radiation from the heating tubes and flow disturbances induced by the nitrogen stream were the primary causes of localized heat concentration.Under no-load conditions,the maximum deviation between simulated and on-site measured temperatures was 1.5%,validating the model’s accuracy.Further-more,this study investigated the trade-offs between temperature uniformity,energy consumption,and construction costs.The findings provide a crucial design basis and a reliable simulation platform for developing and optimizing pyrolysis equipment.展开更多
Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.Ho...Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.However,understanding the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance from a comprehensive perspective is crucial for guiding their future development.This review provides a timely and comprehensive overview of the applications of 2D nanomaterials in oil-based lubrication.First,the bottlenecks and mechanisms of action of 2D nanomaterials are outlined,including adsorption protective films,charge adsorption effects,tribochemical reaction films,interlayer slip,and synergistic effects.On this basis,the review summarizes recent structural regulation strategies for 2D nanomaterials,including doping engineering,surface modification,structural optimization,and interfacial mixing engineering.Then,the focus was on analyzing the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance.The effects of thickness,number of layers,sheet diameter,interlayer spacing,Moiré patterns,wettability,functional groups,concentration,as well as interfacial compatibility and dispersion behavior of 2D nanomaterials were systematically investigated in oil-based lubrication,with the intrinsic correlations resolved through computational simulations.Finally,the review offers a preliminary summary of the significant challenges and future directions for 2D nanomaterials in oil-based lubrication.This review aims to provide valuable insights and development strategies for the rational design of high-performance oil-based lubrication materials.展开更多
BACKGROUND Oil-based iodinated contrast media have excellent contrast properties and are widely used for hysterosalpingographic evaluation of female infertility.On abdominal radiography and computed tomography(CT)scan...BACKGROUND Oil-based iodinated contrast media have excellent contrast properties and are widely used for hysterosalpingographic evaluation of female infertility.On abdominal radiography and computed tomography(CT)scans,their radiodensity is similar to that of metallic objects,which can sometimes lead to diagnostic confusion in the postoperative settings.In this case,retained oil-based contrast medium was observed on an abdominal radiograph following a cesarean section,making it difficult to differentiate from an intraperitoneal foreign body from surgery.The patient was a 37-year-old pregnant woman who was referred to our hospital at 32 weeks and 1 day of pregnancy due to complete placenta previa for mana-gement of pregnancy and delivery.An elective cesarean section was performed at 37 weeks and 3 days.A plain abdominal radiograph taken immediately after surgery revealed a near-round,hyperdense,mass-like shadow with a regular margin in the pelvic cavity.An intraperitoneal foreign body was suspected;therefore,an abdominal CT scan was performed.The foreign body was located on the left side of the pouch of Douglas and had a CT value of 7000 Hounsfield units,similar to that of metals.The CT value strongly suggested the presence of an artificial object.However,further inquiries with the patient and her previous physician revealed a history of hysterosalpingography.Accordingly,retained oil-based iodinated contrast medium was suspected,and observation of the object’s course was adopted.CONCLUSION When intraperitoneal foreign bodies are suspected on postoperative radiographs,the possibility of oil-based iodinated contrast medium retention should be considered.展开更多
The development of materials with excellent microwave absorption(MWA)and electromagnetic interference(EMI)shielding performances has currently received attention.Herein,mesophase pitch-based carbon foam(MPCF)with 3D i...The development of materials with excellent microwave absorption(MWA)and electromagnetic interference(EMI)shielding performances has currently received attention.Herein,mesophase pitch-based carbon foam(MPCF)with 3D interconnected pore structure was prepared through the high pressure pyrolysis of mesophase coal tar pitch.It is found that the 3D interconnected cellular pores of MPCF facilitate multiple reflections of electromagnetic waves,which results in the minimum reflection loss(RLmin)value of MPCF reaches-37.84 dB with the effective absorption bandwidth(EAB)of 5.44 GHz at a thickness of 2.70 mm,and the total average electromagnetic shielding effectiveness(SE_(T))under 3.00 mm thickness achieves 26.52 dB in X-band.Subsequently,MPCF is activated by KOH to obtain activated carbon foam(A-MPCF).The average SE_(T)of A-MPCF achieves 103.00 dB for abundant nanopores on the pore cell walls,which leads to a transition from the multiple reflections of electromagnetic waves on the walls to diffuse reflection.Unfortunately,the reflection coefficient(R)of A-MPCF increases from 0.78 to 0.90.To reduce the R value,Fe_(3)O_(4)/A-MPCF was fabricated via the in situ growth of nano Fe_(3)O_(4)on A-MPCF.Consequently,the R value of Fe_(3)O_(4)/A-MPCF was reduced from 0.90 to 0.74,whereas the MWA performance was only slightly decreased.This work proposes a simple strategy for simultaneously adjusting MWA and EMI shielding performances of materials.展开更多
Waste glass fibers were used as the main raw materials to prepare foamed glass-ceramics with 0-14 wt%H_(3)BO_(3)as a flux agent.The effects of H_(3)BO_(3)on the crystallization process,foaming behavior,and physical pr...Waste glass fibers were used as the main raw materials to prepare foamed glass-ceramics with 0-14 wt%H_(3)BO_(3)as a flux agent.The effects of H_(3)BO_(3)on the crystallization process,foaming behavior,and physical properties of CaO-MgO-Al_(2)O_(3)-SiO_(2)foamed glass-ceramics were investigated.The results showed that the main crystalline phase of the foamed glass-ceramics was anorthite with diopside as a minor crystalline phase,which exhibited a typical surface crystallization process.The addition of H_(3)BO_(3)modified the surface of glass powders and inhibited crystal precipitation obviously.The low melting point of H_(3)BO_(3)and the decrease of crystallinity jointly promoted the growth of pores,resulting in a reduction of bulk density and an increase in porosity.The compressive strength and thermal conductivity of the samples were linearly related to the bulk density.In particular,the sample added with 10 wt%H_(3)BO_(3)exhibited excellent properties,possessing a low coefficient of thermal conductivity 0.081 W/(m·K)and relatively high compressive strength 3.36 MPa.展开更多
Directional three-dimensional carbon-based foams are emerging as highly attractive candidates for promising electromagnetic wave absorbing materials(EWAMs)thanks to their unique architecture,but their construction usu...Directional three-dimensional carbon-based foams are emerging as highly attractive candidates for promising electromagnetic wave absorbing materials(EWAMs)thanks to their unique architecture,but their construction usually involves complex procedures and extremely depends on unidirectional freezing technique.Herein,we propose a groundbreaking approach that leverages the assemblies of salting-out protein induced by ammonium metatungstate(AM)as the precursor,and then acquire directional three-dimensional carbon-based foams through simple pyrolysis.The electrostatic interaction between AM and protein ensures well dispersion of WC_(1−x)nanoparticles on carbon frameworks.The content of WC_(1−x)nanoparticles can be rationally regulated by AM dosage,and it also affects the electromagnetic(EM)properties of final carbon-based foams.The optimized foam exhibits exceptional EM absorption performance,achieving a remarkable minimum reflection loss of−72.0 dB and an effective absorption bandwidth of 6.3 GHz when EM wave propagates parallel to the directional pores.Such performance benefits from the synergistic effects of macroporous architecture and compositional design.Although there is a directional dependence of EM absorption,radar stealth simulation demonstrates that these foams can still promise considerable reduction in radar cross section with the change of incident angle.Moreover,COMSOL simulation further identifies their good performance in preventing EM interference among different electronic components.展开更多
Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic ...Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic mechanical properties. However, cement-iron ore tailings foam composite(CIFC), a sustainable material utilizing iron ore tailings to partially replace cement, has not been investigated under dynamic loading. This study investigates the dynamic compressive behavior of CIFC with 1%–2.5% PPF content and 3–12 mm PPF lengths under various strain rates. The microstructural characteristics were analyzed prior to dynamic testing. X-ray diffraction(XRD) identified crystalline phases including CaCO_(3)Fe_(2)O_(3), SiO, C-S-H gel, and ettringite. Scanning electron microscopy(SEM) observations demonstrated that appropriate PPF_(2) parameters(e.g., C2L9, a CIFC specimen containing 2% PPF with 9 mm length) enhance fiber-matrix bonding and minimize interconnected pores and microcracks, revealing pronounced fiber bridging effects. Split Hopkinson pressure bar(SHPB) tests were then conducted at strain rates of 120–250 s^(-1), showing that the dynamic properties of CIFC were highly dependent on both strain rates and PPF parameters. Compared to other specimens, C2L9 exhibited a more intact failure pattern with superior compressive strength and energy dissipation capacity, despite showing reduced dynamic increase factor(DIF) and normalized energy dissipation(NED) values. These findings provide practical guidance for applying CIFC with varying PPF parameters in impact-resistant structural designs.展开更多
Estimating the properties of foam-conditioned clay soils is important for both conditioning and recycling goals in earth pressure balance(EPB)shield tunneling.In this study,the vacuum dewatering behaviors of foam-cond...Estimating the properties of foam-conditioned clay soils is important for both conditioning and recycling goals in earth pressure balance(EPB)shield tunneling.In this study,the vacuum dewatering behaviors of foam-conditioned clay soils were investigated,with their potential use as an alternative means to assess foam optimization being examined.A series of laboratory and fieldtests was conducted,including vacuum dewatering tests that considered the effects of filtrationtime and pressure,vane shear tests,and improved cone pullout tests under different gravimetric water content(w)and foam injection ratio(FIR)conditions.It was found that the filtrate loss(FL),which characterizes dewaterability,was increased by extended vacuum filtrationtime and elevated pressure.While increases in w and FIR enhanced FL,reductions were observed in the undrained shear strength(cu),tangential adhesion stress(Fs),and normal adhesion stress(Fn).Furthermore,a linear decrease in FL with increasing mechanical indices(cu,Fs,and Fn)was demonstrated by both laboratory and fielddata fittingresults,regardless of w,FIR,and dewatering conditions.This study provides novel insights into the understanding of vacuum dewatering mechanisms in foam-conditioned clay soils,while a simple approach is proposed for evaluating foam conditioning effectiveness in EPB shield tunneling applications.展开更多
One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were teste...One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were tested to investigate the characteristics of gas-hydrate formation,agglomeration and inhibition by an experimental system under the temperature of 4 ？C and pressure of 20 MPa,which would be similar to the case of 2000 m water depth.The results validate the hydrate shell formation model and show that the water cut can greatly influence hydrate formation and agglomeration behaviors in the OBDF.The oleophobic effect enhanced by hydrate shell formation which weakens or destroys the interfacial films effect and the hydrophilic effect are the dominant agglomeration mechanism of hydrate particles.The formation of gas hydrates in OBDF is easier and quicker than in water-based drilling fluids in deep-water conditions of low temperature and high pressure because the former is a W/O dispersive emulsion which means much more gas-water interfaces and nucleation sites than the later.Higher ethylene glycol concentrations can inhibit the formation of gas hydrates and to some extent also act as an anti-agglomerant to inhibit hydrates agglomeration in the OBDF.展开更多
The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental ...The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.展开更多
A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based...A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation,followed by in situ polymerization of MF precondensates as an outer shell.The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance,and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions.It was demonstrated that MF microcapsules containing clove oil were prepared successfully.The amount and the composition of the intermediate polyacrylate bridging layer were critical.Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt%and the concentration of acrylic acid(AA)increased to 10 wt%in polyacrylate.In addition,MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method.The work suggests that this new approach can be potentially used to encapsulate various core materials,tuning the shell properties of microcapsules such as thickness,mechanical strength and release properties.展开更多
In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for M...In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for MRF was designed. Moreover, relevant experiments were carded out and the relationship between squeezing pressure and braking torque was proposed. Experiments results showed that the yield stress of MRF improved linearly with the increasing of external squeezing pressure and the braking torque increased three times when external squeezing pressure achieved 2 MPa.展开更多
Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol fr...Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol from wastewater and obtain valuable phenolic compound.One of potential method is extraction using green based liquid organic solvent.Therefore,the feasibility of using palm oil was investigated.In this research,palm oil based organic phase was used as diluents to treat a simulated wastewater containing 300×10^(-6) of phenol solution using emulsion liquid membrane process(ELM).The stability of water-in-oil(W/O) emulsion on diluent composition and the parameters affecting the phenol removal efficiency and stability of the emulsion;such as emulsification speed,emulsification time,agitation speed,surfactant concentration,pH of external phase,contact time,stripping agent concentration and treat ratio were carried out.The results of ELM study showed that at ratio7 to 3 of palm oil to kerosene,5 min and 1300 r·min^(-1) of emulsification process the stabile primary emulsion were formed.Also,no carrier is needed to facilitate the phenol extraction.In experimental conditions of500 r·min^(-1) of agitation speed,3%Span 80,pH 8 of external phase,5 min of contact time,0.1 mol·L^(-1) NaOH as stripping agent and 1:10 of treat ratio,the ELM process was very promising for removing the phenol from the wastewater.The extraction performance at about 83%of phenol was removed for simulated wastewater and an enrichment of phenol in recovery phase as phenolate compound was around 11 times.展开更多
Traditional oil-based drilling muds(OBMs) have a relatively high solid content, which is detrimental to penetration rate increase and reservoir protection. Aimed at solving this problem, an organoclay-free OBM system ...Traditional oil-based drilling muds(OBMs) have a relatively high solid content, which is detrimental to penetration rate increase and reservoir protection. Aimed at solving this problem, an organoclay-free OBM system was studied, the synthesis methods and functioning mechanism of key additives were introduced, and performance evaluation of the system was performed. The rheology modifier was prepared by reacting a dimer fatty acid with diethanolamine, the primary emulsifier was made by oxidation and addition reaction of fatty acids, the secondary emulsifier was made by amidation of a fatty acid, and finally the fluid loss additive of water-soluble acrylic resin was synthesized by introducing acrylic acid into styrene/butyl acrylate polymerization. The rheology modifier could enhance the attraction between droplets, particles in the emulsion via intermolecular hydrogen bonding and improve the shear stress by forming a three-dimensional network structure in the emulsion. Lab experimental results show that the organoclay-free OBM could tolerate temperatures up to 220 ?C and HTHP filtration is less than 5 m L. Compared with the traditional OBMs, the organoclay-free OBM has low plastic viscosity, high shear stress, high ratio of dynamic shear force to plastic viscosity and high permeability recovery, which are beneficial to penetration rate increase, hole cleaning and reservoir protection.展开更多
When drilling deep wells and ultra-deep wells, the downhole high temperature and high pressure environment will affect the emulsion stability of oil-based drilling fluids. Moreover, neither the demulsification voltage...When drilling deep wells and ultra-deep wells, the downhole high temperature and high pressure environment will affect the emulsion stability of oil-based drilling fluids. Moreover, neither the demulsification voltage method nor the centrifugal method currently used to evaluate the stability of oil-based drilling fluids can reflect the emulsification stability of drilling fluids under high temperature and high pressure on site. Therefore, a high-temperature and high-pressure oil-based drilling fluid emulsion stability evaluation instrument is studied, which is mainly composed of a high-temperature autoclave body, a test electrode, a temperature control system, a pressure control system, and a test system. The stability test results of the instrument show that the instrument can achieve stable testing and the test data has high reliability. This instrument is used to analyze the factors affecting the emulsion stability of oil-based drilling fluids. The experimental results show that under the same conditions, the higher the stirring speed, the better the emulsion stability of the drilling fluid;the longer the stirring time, the better the emulsion stability of the drilling fluid;the greater the oil-water ratio, the better the emulsion stability of the drilling fluid. And the test results of the emulsification stability of oil-based drilling fluids at high temperature and high pressure show that under the same pressure, as the temperature rises, the emulsion stability of oil-based drilling fluids is significantly reduced;at the same temperature, the With the increase in pressure, the emulsion stability of oil-based drilling fluids is in a downward trend, but the decline is not large. Relatively speaking, the influence of temperature on the emulsion stability of oil-based drilling fluids is greater than that of pressure.展开更多
As the oil and gas industries continue to increase their activity in deep water, gas hydrate hazards will become more serious and challenging, both at present and in the future. Accurate predictions of the hydrate-fre...As the oil and gas industries continue to increase their activity in deep water, gas hydrate hazards will become more serious and challenging, both at present and in the future. Accurate predictions of the hydrate-free zone and the suitable addition of salts and/or alcohols in preparing drilling fluids are particularly important both in preventing hydrate problems and decreasing the cost of drilling operations. In this paper, we compared several empirical correlations commonly used to estimate the hydrate inhibition effect of aqueous organic and electrolyte solutions using experiments with ethylene glycol （EG） as a hydrate inhibitor. The results show that the Najibi et al. correlation （for single and mixed thermodynamic inhibitors） and the Ostergaard et al. empirical correlation （for single thermodynamic inhibitors） are suitable for estimating the hydrate safety margin of oil-based drilling fluids （OBDFs） in the presence of thermodynamic hydrate inhibitors. According to the two correlations, the OBDF, composed of 1.6 L vaporizing oil, 2% emulsifying agent, 1% organobentonite, 0.5% SP-1, 1% LP-1, 10% water and 40% EG, can be safely used at a water depth of up to 1900 m. However, for more accurate predictions for drilling fluids, the effects of the solid phase, especially bentonite, on hydrate inhibition need to be considered and included in the application of these two empirical correlations.展开更多
To find out the relationship between the oil-based mud,the formation fluid and the extracted gas,we use a thermodynamic approach based on static headspace gas chromatography technique to calculate the partition coeffi...To find out the relationship between the oil-based mud,the formation fluid and the extracted gas,we use a thermodynamic approach based on static headspace gas chromatography technique to calculate the partition coefficients of 47 kinds of light hydrocarbons compounds between nC5 and nC8 in two kinds of oil-based mud-air systems,and reconstruct the original formation fluid composition under thermodynamic equilibrium.The oil-based drilling mud has little effect on the formation fluid compositions in the range of nC5-nC8(less than 1%for low-toxicity oil-based mud and less than 10%for oil-based mud).For most light hydrocarbon compositions,the partition coefficients obtained by vapor phase calibration and the direct quantitative methods have errors of less than 10%,and the partition coefficients obtained by direct quantitative method are more accurate.The reconstructed compositions of the two kinds of crude oil have match degrees of 91%and 89%with their real compositions,proving the feasibility and accuracy of reconstructing the composition of original formation fluid by using partition coefficients of light hydrocarbon compositions between nC5 and nC8.展开更多
In this paper,based on Fluent software,a five-nozzle gasifier reactor was established to simulate the gasification process of oil-based drill cuttings coal-water slurry.The influence of concentration and oxygen/carbon...In this paper,based on Fluent software,a five-nozzle gasifier reactor was established to simulate the gasification process of oil-based drill cuttings coal-water slurry.The influence of concentration and oxygen/carbon atomic ratio on the gasification process of oil-based drill cuttings coal-water slurry was investigated.The results show that when the oxygen flow is constant,the outlet temperature of gasifier decreases,the content of effective gas increases,and the carbon conversion rate decreases with the increase of concentration;When the ratio of oxygen to carbon atoms is constant,the effective gas content rises and the temperature rises with the increase of the concentration,and the carbon conversion rate reaches the maximum value when the concentration of oil-based drill cuttings coal-water slurry is 65%;When the concentration is constant,the effective gas content decreases and the outlet temperature rises with the increase of the oxygen/carbon atom ratio,and the carbon conversion rate reaches 99.80%when the oxygen/carbon atom ratio is 1.03.It shows that this method can effectively decompose the organic matter in oilbased drill cuttings and realize the efficient and cooperative treatment of oil-based drill cuttings.展开更多
基金from the Fundamental Research Funds for the Central Non-profit Research Institution of CAF(No.CAFYBB2018MA001).
文摘Phenolic foams(PFs)as thermal insulation material with outstanding flame retardancy are required to match society’s ever-expanding safety expectations;however,a trade-off exists between flame retardancy and toughness.Here,for the first time,we synthesized a novel reactive phosphorus-containing tung-oil-based derivative and used it to toughen PF,resulting in PFs with a combination of excellent mechanical properties and flame retardancy.Compared with pure PF,the modified PFs exhibit enhanced mechanical properties,with specific compressive and flexural strengths as high as 5.67 MPa and 12.46 MPa,which represent increases of 90.67%and 178.7%over those of pure PF,respectively.Meanwhile,the limiting oxygen index(LOI)values of the modified PFs are improved as much as 40.83%.Scanning electron microscopy micrographs show that the microstructure of the modified PFs is better than that of pure PF,with a more uniform cell morphology,a narrower pore size distribution range,and a smaller average pore size,all of which are beneficial to the foam’s mechanical properties.This study provides a scientific paradigm for the development of advanced PFs based on renewable biological resources.
基金the National Natural Science Foundation of China(42074134,42474152,42374150)CNPC Innovation Found(2024DQ02-0152).
文摘The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel logging method for detection of high-resistance formations in OBM using highfrequency electrodes. The method addresses the issue of shallow depth of investigation(DOI) in existing electrical logging instruments, while simultaneously ensuring the vertical resolution. Based on the principle of current continuity, the total impedance of the loop is obtained by equating the measurement loop to the series form of a capacitively coupled circuit. and its validity is verified in a homogeneous formation model and a radial two-layer formation model with a mud standoff. Then, the instrument operating frequency and electrode system parameters were preferentially determined by numerical simulation, and the effect of mud gap on impedance measurement was investigated. Subsequently, the DOI of the instrument was investigated utilizing the pseudo-geometric factor defined by the real part of impedance. It was determined that the detection depth of the instrument is 8.74 cm, while the effective vertical resolution was not less than 2 cm. Finally, a focused high-frequency electrode-type instrument was designed by introducing a pair of focused electrodes, which effectively enhanced the DOI of the instrument and was successfully deployed in the Oklahoma formation model. The simulation results demonstrate that the novel method can achieve a detection depth of 17.40 cm in highly-resistive formations drilling with OBM, which is approximately twice the depth of detection of the existing oil-based mud microimager instruments. Furthermore, its effective vertical resolution remains at or above 2 cm,which is comparable to the resolution of the existing OBM electrical logging instrument.
基金funded by the key research on industrialization technologies of low-cost highenergy-density cathode materials(project number:2023GY008)the Sichuan Provincial Science and Technology Program(project number:2024NSFSC1406).
文摘To address the issue of uneven temperature distribution in shale gas oil-based drill cuttings pyrolysis furnaces,a numerical model was developed using Fluent software.The effects of nitrogen flow rate,heating tube spacing,and furnace dimensions on the internal temperature field were thoroughly analyzed from a mechanistic perspective.The results indicated that non-uniform radiation from the heating tubes and flow disturbances induced by the nitrogen stream were the primary causes of localized heat concentration.Under no-load conditions,the maximum deviation between simulated and on-site measured temperatures was 1.5%,validating the model’s accuracy.Further-more,this study investigated the trade-offs between temperature uniformity,energy consumption,and construction costs.The findings provide a crucial design basis and a reliable simulation platform for developing and optimizing pyrolysis equipment.
基金supported by the National Natural Science Foundation of China(No.51874036)the Natural Science Foundation of Ningxia(No.2024AAC02034)。
文摘Two-dimensional(2D) nanomaterials have always been regarded as having great development potential in the field of oil-based lubrication due to their designable structures,functional groups,and abundant active sites.However,understanding the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance from a comprehensive perspective is crucial for guiding their future development.This review provides a timely and comprehensive overview of the applications of 2D nanomaterials in oil-based lubrication.First,the bottlenecks and mechanisms of action of 2D nanomaterials are outlined,including adsorption protective films,charge adsorption effects,tribochemical reaction films,interlayer slip,and synergistic effects.On this basis,the review summarizes recent structural regulation strategies for 2D nanomaterials,including doping engineering,surface modification,structural optimization,and interfacial mixing engineering.Then,the focus was on analyzing the structure-performance relationship between the chemical structure of 2D nanomaterials and their lubrication performance.The effects of thickness,number of layers,sheet diameter,interlayer spacing,Moiré patterns,wettability,functional groups,concentration,as well as interfacial compatibility and dispersion behavior of 2D nanomaterials were systematically investigated in oil-based lubrication,with the intrinsic correlations resolved through computational simulations.Finally,the review offers a preliminary summary of the significant challenges and future directions for 2D nanomaterials in oil-based lubrication.This review aims to provide valuable insights and development strategies for the rational design of high-performance oil-based lubrication materials.
文摘BACKGROUND Oil-based iodinated contrast media have excellent contrast properties and are widely used for hysterosalpingographic evaluation of female infertility.On abdominal radiography and computed tomography(CT)scans,their radiodensity is similar to that of metallic objects,which can sometimes lead to diagnostic confusion in the postoperative settings.In this case,retained oil-based contrast medium was observed on an abdominal radiograph following a cesarean section,making it difficult to differentiate from an intraperitoneal foreign body from surgery.The patient was a 37-year-old pregnant woman who was referred to our hospital at 32 weeks and 1 day of pregnancy due to complete placenta previa for mana-gement of pregnancy and delivery.An elective cesarean section was performed at 37 weeks and 3 days.A plain abdominal radiograph taken immediately after surgery revealed a near-round,hyperdense,mass-like shadow with a regular margin in the pelvic cavity.An intraperitoneal foreign body was suspected;therefore,an abdominal CT scan was performed.The foreign body was located on the left side of the pouch of Douglas and had a CT value of 7000 Hounsfield units,similar to that of metals.The CT value strongly suggested the presence of an artificial object.However,further inquiries with the patient and her previous physician revealed a history of hysterosalpingography.Accordingly,retained oil-based iodinated contrast medium was suspected,and observation of the object’s course was adopted.CONCLUSION When intraperitoneal foreign bodies are suspected on postoperative radiographs,the possibility of oil-based iodinated contrast medium retention should be considered.
基金Supported by the National Natural Science Foundation of China(22378181).
文摘The development of materials with excellent microwave absorption(MWA)and electromagnetic interference(EMI)shielding performances has currently received attention.Herein,mesophase pitch-based carbon foam(MPCF)with 3D interconnected pore structure was prepared through the high pressure pyrolysis of mesophase coal tar pitch.It is found that the 3D interconnected cellular pores of MPCF facilitate multiple reflections of electromagnetic waves,which results in the minimum reflection loss(RLmin)value of MPCF reaches-37.84 dB with the effective absorption bandwidth(EAB)of 5.44 GHz at a thickness of 2.70 mm,and the total average electromagnetic shielding effectiveness(SE_(T))under 3.00 mm thickness achieves 26.52 dB in X-band.Subsequently,MPCF is activated by KOH to obtain activated carbon foam(A-MPCF).The average SE_(T)of A-MPCF achieves 103.00 dB for abundant nanopores on the pore cell walls,which leads to a transition from the multiple reflections of electromagnetic waves on the walls to diffuse reflection.Unfortunately,the reflection coefficient(R)of A-MPCF increases from 0.78 to 0.90.To reduce the R value,Fe_(3)O_(4)/A-MPCF was fabricated via the in situ growth of nano Fe_(3)O_(4)on A-MPCF.Consequently,the R value of Fe_(3)O_(4)/A-MPCF was reduced from 0.90 to 0.74,whereas the MWA performance was only slightly decreased.This work proposes a simple strategy for simultaneously adjusting MWA and EMI shielding performances of materials.
基金Funded by Shandong Provincial Youth Innovation Team Development Plan of Colleges and Universities(No.2022KJ100)National Natural Science Foundation of China(No.52172019)。
文摘Waste glass fibers were used as the main raw materials to prepare foamed glass-ceramics with 0-14 wt%H_(3)BO_(3)as a flux agent.The effects of H_(3)BO_(3)on the crystallization process,foaming behavior,and physical properties of CaO-MgO-Al_(2)O_(3)-SiO_(2)foamed glass-ceramics were investigated.The results showed that the main crystalline phase of the foamed glass-ceramics was anorthite with diopside as a minor crystalline phase,which exhibited a typical surface crystallization process.The addition of H_(3)BO_(3)modified the surface of glass powders and inhibited crystal precipitation obviously.The low melting point of H_(3)BO_(3)and the decrease of crystallinity jointly promoted the growth of pores,resulting in a reduction of bulk density and an increase in porosity.The compressive strength and thermal conductivity of the samples were linearly related to the bulk density.In particular,the sample added with 10 wt%H_(3)BO_(3)exhibited excellent properties,possessing a low coefficient of thermal conductivity 0.081 W/(m·K)and relatively high compressive strength 3.36 MPa.
基金financially supported by the National Natural Science Foundation of China(Nos.22475057 and No.52373262).
文摘Directional three-dimensional carbon-based foams are emerging as highly attractive candidates for promising electromagnetic wave absorbing materials(EWAMs)thanks to their unique architecture,but their construction usually involves complex procedures and extremely depends on unidirectional freezing technique.Herein,we propose a groundbreaking approach that leverages the assemblies of salting-out protein induced by ammonium metatungstate(AM)as the precursor,and then acquire directional three-dimensional carbon-based foams through simple pyrolysis.The electrostatic interaction between AM and protein ensures well dispersion of WC_(1−x)nanoparticles on carbon frameworks.The content of WC_(1−x)nanoparticles can be rationally regulated by AM dosage,and it also affects the electromagnetic(EM)properties of final carbon-based foams.The optimized foam exhibits exceptional EM absorption performance,achieving a remarkable minimum reflection loss of−72.0 dB and an effective absorption bandwidth of 6.3 GHz when EM wave propagates parallel to the directional pores.Such performance benefits from the synergistic effects of macroporous architecture and compositional design.Although there is a directional dependence of EM absorption,radar stealth simulation demonstrates that these foams can still promise considerable reduction in radar cross section with the change of incident angle.Moreover,COMSOL simulation further identifies their good performance in preventing EM interference among different electronic components.
基金supported by the National Science Foundation for Excellent Young Scholars of China (Grant No.52422809)the National Natural Science Foundation of China (Grant No.52208491)。
文摘Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic mechanical properties. However, cement-iron ore tailings foam composite(CIFC), a sustainable material utilizing iron ore tailings to partially replace cement, has not been investigated under dynamic loading. This study investigates the dynamic compressive behavior of CIFC with 1%–2.5% PPF content and 3–12 mm PPF lengths under various strain rates. The microstructural characteristics were analyzed prior to dynamic testing. X-ray diffraction(XRD) identified crystalline phases including CaCO_(3)Fe_(2)O_(3), SiO, C-S-H gel, and ettringite. Scanning electron microscopy(SEM) observations demonstrated that appropriate PPF_(2) parameters(e.g., C2L9, a CIFC specimen containing 2% PPF with 9 mm length) enhance fiber-matrix bonding and minimize interconnected pores and microcracks, revealing pronounced fiber bridging effects. Split Hopkinson pressure bar(SHPB) tests were then conducted at strain rates of 120–250 s^(-1), showing that the dynamic properties of CIFC were highly dependent on both strain rates and PPF parameters. Compared to other specimens, C2L9 exhibited a more intact failure pattern with superior compressive strength and energy dissipation capacity, despite showing reduced dynamic increase factor(DIF) and normalized energy dissipation(NED) values. These findings provide practical guidance for applying CIFC with varying PPF parameters in impact-resistant structural designs.
基金supported by the National Youth Top-notch Talent Support Program of China(Grant No.00389335)the National Natural Science Foundation of China(Grant No.52378392)the“Foal Eagle Program”Youth Top-notch Talent Project of Fujian Province(Grant No.00387088).
文摘Estimating the properties of foam-conditioned clay soils is important for both conditioning and recycling goals in earth pressure balance(EPB)shield tunneling.In this study,the vacuum dewatering behaviors of foam-conditioned clay soils were investigated,with their potential use as an alternative means to assess foam optimization being examined.A series of laboratory and fieldtests was conducted,including vacuum dewatering tests that considered the effects of filtrationtime and pressure,vane shear tests,and improved cone pullout tests under different gravimetric water content(w)and foam injection ratio(FIR)conditions.It was found that the filtrate loss(FL),which characterizes dewaterability,was increased by extended vacuum filtrationtime and elevated pressure.While increases in w and FIR enhanced FL,reductions were observed in the undrained shear strength(cu),tangential adhesion stress(Fs),and normal adhesion stress(Fn).Furthermore,a linear decrease in FL with increasing mechanical indices(cu,Fs,and Fn)was demonstrated by both laboratory and fielddata fittingresults,regardless of w,FIR,and dewatering conditions.This study provides novel insights into the understanding of vacuum dewatering mechanisms in foam-conditioned clay soils,while a simple approach is proposed for evaluating foam conditioning effectiveness in EPB shield tunneling applications.
基金supported by Project 863 (No. 2006AA09Z316)NSFC (No. 50704028 and 40974071)
文摘One of the main challenges in deep-water drilling is gas-hydrate plugs,which make the drilling unsafe.Some oil-based drilling fluids（OBDF） that would be used for deep-water drilling in the South China Sea were tested to investigate the characteristics of gas-hydrate formation,agglomeration and inhibition by an experimental system under the temperature of 4 ？C and pressure of 20 MPa,which would be similar to the case of 2000 m water depth.The results validate the hydrate shell formation model and show that the water cut can greatly influence hydrate formation and agglomeration behaviors in the OBDF.The oleophobic effect enhanced by hydrate shell formation which weakens or destroys the interfacial films effect and the hydrophilic effect are the dominant agglomeration mechanism of hydrate particles.The formation of gas hydrates in OBDF is easier and quicker than in water-based drilling fluids in deep-water conditions of low temperature and high pressure because the former is a W/O dispersive emulsion which means much more gas-water interfaces and nucleation sites than the later.Higher ethylene glycol concentrations can inhibit the formation of gas hydrates and to some extent also act as an anti-agglomerant to inhibit hydrates agglomeration in the OBDF.
基金Project(50574061) supported by the National Natural Science Foundation of ChinaProject(IRT0411) supported by the Changjiang Scholars and Innovative Research Team,Ministry of Education
文摘The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.
基金Supported by the National Natural Science Foundation of China(21466016,21577053)the Natural Science Foundation of Yunnan Province(2016FB024).
文摘A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation,followed by in situ polymerization of MF precondensates as an outer shell.The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance,and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions.It was demonstrated that MF microcapsules containing clove oil were prepared successfully.The amount and the composition of the intermediate polyacrylate bridging layer were critical.Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt%and the concentration of acrylic acid(AA)increased to 10 wt%in polyacrylate.In addition,MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method.The work suggests that this new approach can be potentially used to encapsulate various core materials,tuning the shell properties of microcapsules such as thickness,mechanical strength and release properties.
基金Funded by National Natural Science Foundation of China(No.51475454)National Natural Science Foundation of JiangsuProvince(No.BK20151144)+1 种基金Fundamental Research Funds forthe Central Universities(No.2014QNA38)Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)
文摘In order to study the squeeze-strengthening effect of silicone oil-based magnetorheological fluid （MRF）, theoretical basis of disc squeezing brake was presented and a squeezing braking characteristics test-bed for MRF was designed. Moreover, relevant experiments were carded out and the relationship between squeezing pressure and braking torque was proposed. Experiments results showed that the yield stress of MRF improved linearly with the increasing of external squeezing pressure and the braking torque increased three times when external squeezing pressure achieved 2 MPa.
基金Supported by the Ministry of Higher Education(MOHE)Universiti Teknologi Malaysia(RU Research GrantGUP:Q.J130000.2546.12H50)
文摘Phenol is considered as pollutant due to its toxicity and carcinogenic effect.Thus,variety of innovative methods for separation and recovery of phenolic compounds is developed in order to remove the unwanted phenol from wastewater and obtain valuable phenolic compound.One of potential method is extraction using green based liquid organic solvent.Therefore,the feasibility of using palm oil was investigated.In this research,palm oil based organic phase was used as diluents to treat a simulated wastewater containing 300×10^(-6) of phenol solution using emulsion liquid membrane process(ELM).The stability of water-in-oil(W/O) emulsion on diluent composition and the parameters affecting the phenol removal efficiency and stability of the emulsion;such as emulsification speed,emulsification time,agitation speed,surfactant concentration,pH of external phase,contact time,stripping agent concentration and treat ratio were carried out.The results of ELM study showed that at ratio7 to 3 of palm oil to kerosene,5 min and 1300 r·min^(-1) of emulsification process the stabile primary emulsion were formed.Also,no carrier is needed to facilitate the phenol extraction.In experimental conditions of500 r·min^(-1) of agitation speed,3%Span 80,pH 8 of external phase,5 min of contact time,0.1 mol·L^(-1) NaOH as stripping agent and 1:10 of treat ratio,the ELM process was very promising for removing the phenol from the wastewater.The extraction performance at about 83%of phenol was removed for simulated wastewater and an enrichment of phenol in recovery phase as phenolate compound was around 11 times.
基金Supported by the Basic Research Funds Reserved to State-run Universities(18CX02171A,18CX02033A)
文摘Traditional oil-based drilling muds(OBMs) have a relatively high solid content, which is detrimental to penetration rate increase and reservoir protection. Aimed at solving this problem, an organoclay-free OBM system was studied, the synthesis methods and functioning mechanism of key additives were introduced, and performance evaluation of the system was performed. The rheology modifier was prepared by reacting a dimer fatty acid with diethanolamine, the primary emulsifier was made by oxidation and addition reaction of fatty acids, the secondary emulsifier was made by amidation of a fatty acid, and finally the fluid loss additive of water-soluble acrylic resin was synthesized by introducing acrylic acid into styrene/butyl acrylate polymerization. The rheology modifier could enhance the attraction between droplets, particles in the emulsion via intermolecular hydrogen bonding and improve the shear stress by forming a three-dimensional network structure in the emulsion. Lab experimental results show that the organoclay-free OBM could tolerate temperatures up to 220 ?C and HTHP filtration is less than 5 m L. Compared with the traditional OBMs, the organoclay-free OBM has low plastic viscosity, high shear stress, high ratio of dynamic shear force to plastic viscosity and high permeability recovery, which are beneficial to penetration rate increase, hole cleaning and reservoir protection.
文摘When drilling deep wells and ultra-deep wells, the downhole high temperature and high pressure environment will affect the emulsion stability of oil-based drilling fluids. Moreover, neither the demulsification voltage method nor the centrifugal method currently used to evaluate the stability of oil-based drilling fluids can reflect the emulsification stability of drilling fluids under high temperature and high pressure on site. Therefore, a high-temperature and high-pressure oil-based drilling fluid emulsion stability evaluation instrument is studied, which is mainly composed of a high-temperature autoclave body, a test electrode, a temperature control system, a pressure control system, and a test system. The stability test results of the instrument show that the instrument can achieve stable testing and the test data has high reliability. This instrument is used to analyze the factors affecting the emulsion stability of oil-based drilling fluids. The experimental results show that under the same conditions, the higher the stirring speed, the better the emulsion stability of the drilling fluid;the longer the stirring time, the better the emulsion stability of the drilling fluid;the greater the oil-water ratio, the better the emulsion stability of the drilling fluid. And the test results of the emulsification stability of oil-based drilling fluids at high temperature and high pressure show that under the same pressure, as the temperature rises, the emulsion stability of oil-based drilling fluids is significantly reduced;at the same temperature, the With the increase in pressure, the emulsion stability of oil-based drilling fluids is in a downward trend, but the decline is not large. Relatively speaking, the influence of temperature on the emulsion stability of oil-based drilling fluids is greater than that of pressure.
基金supported by the National Natural Science Foundation (No. 50704028, 50904053)the Project 863 (No.2006AA09Z316)+1 种基金the Fundamental Research Funds for the Central Universities (No. CUGL100410)supported by the Opening Project of National Laboratory on Scientific Drilling, China University of Geosciences at Beijing (No. NLSD200901)
文摘As the oil and gas industries continue to increase their activity in deep water, gas hydrate hazards will become more serious and challenging, both at present and in the future. Accurate predictions of the hydrate-free zone and the suitable addition of salts and/or alcohols in preparing drilling fluids are particularly important both in preventing hydrate problems and decreasing the cost of drilling operations. In this paper, we compared several empirical correlations commonly used to estimate the hydrate inhibition effect of aqueous organic and electrolyte solutions using experiments with ethylene glycol （EG） as a hydrate inhibitor. The results show that the Najibi et al. correlation （for single and mixed thermodynamic inhibitors） and the Ostergaard et al. empirical correlation （for single thermodynamic inhibitors） are suitable for estimating the hydrate safety margin of oil-based drilling fluids （OBDFs） in the presence of thermodynamic hydrate inhibitors. According to the two correlations, the OBDF, composed of 1.6 L vaporizing oil, 2% emulsifying agent, 1% organobentonite, 0.5% SP-1, 1% LP-1, 10% water and 40% EG, can be safely used at a water depth of up to 1900 m. However, for more accurate predictions for drilling fluids, the effects of the solid phase, especially bentonite, on hydrate inhibition need to be considered and included in the application of these two empirical correlations.
文摘To find out the relationship between the oil-based mud,the formation fluid and the extracted gas,we use a thermodynamic approach based on static headspace gas chromatography technique to calculate the partition coefficients of 47 kinds of light hydrocarbons compounds between nC5 and nC8 in two kinds of oil-based mud-air systems,and reconstruct the original formation fluid composition under thermodynamic equilibrium.The oil-based drilling mud has little effect on the formation fluid compositions in the range of nC5-nC8(less than 1%for low-toxicity oil-based mud and less than 10%for oil-based mud).For most light hydrocarbon compositions,the partition coefficients obtained by vapor phase calibration and the direct quantitative methods have errors of less than 10%,and the partition coefficients obtained by direct quantitative method are more accurate.The reconstructed compositions of the two kinds of crude oil have match degrees of 91%and 89%with their real compositions,proving the feasibility and accuracy of reconstructing the composition of original formation fluid by using partition coefficients of light hydrocarbon compositions between nC5 and nC8.
基金This research was funded by the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China(KYCX21_2815).
文摘In this paper,based on Fluent software,a five-nozzle gasifier reactor was established to simulate the gasification process of oil-based drill cuttings coal-water slurry.The influence of concentration and oxygen/carbon atomic ratio on the gasification process of oil-based drill cuttings coal-water slurry was investigated.The results show that when the oxygen flow is constant,the outlet temperature of gasifier decreases,the content of effective gas increases,and the carbon conversion rate decreases with the increase of concentration;When the ratio of oxygen to carbon atoms is constant,the effective gas content rises and the temperature rises with the increase of the concentration,and the carbon conversion rate reaches the maximum value when the concentration of oil-based drill cuttings coal-water slurry is 65%;When the concentration is constant,the effective gas content decreases and the outlet temperature rises with the increase of the oxygen/carbon atom ratio,and the carbon conversion rate reaches 99.80%when the oxygen/carbon atom ratio is 1.03.It shows that this method can effectively decompose the organic matter in oilbased drill cuttings and realize the efficient and cooperative treatment of oil-based drill cuttings.
