Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjec...Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.展开更多
目前对土工格室加筋路堤研究主要集中在静载条件下,动载条件下研究的比较少。为研究分级循环荷载下土工格室加筋路堤的力学性能,采用USTX-2000的动力加载装置进行加载,对土工格室加筋路堤在不同加筋层数、格室高度、格室焊距等工况下进...目前对土工格室加筋路堤研究主要集中在静载条件下,动载条件下研究的比较少。为研究分级循环荷载下土工格室加筋路堤的力学性能,采用USTX-2000的动力加载装置进行加载,对土工格室加筋路堤在不同加筋层数、格室高度、格室焊距等工况下进行一系列模型试验。对分级循环荷载下路堤的竖向变形和坡面法向变形进行研究,并与固定振幅循环荷载及静载作用下的路堤进行对比分析,研究不同加载方案路堤力学性能的差异性。试验结果表明,土工格室加筋能显著提高路堤承受分级循环荷载的能力和减小竖向累积沉降量,在加筋间距一定的情况下,两层及以上加筋效果比单层加筋效果更显著,格室高度增大和格室焊距减小均可不同程度提高路堤承受分级循环荷载能力并减小竖向累积沉降量;加筋可减小路堤分级循环荷载下的坡面法向变形,格室高度增大和格室焊距减小在分级循环荷载幅值相同时均能减小坡顶和坡中处的法向累积变形;分级循环荷载作用下,当振次≥8 000或幅值≥80 k Pa时,路堤竖向累积沉降量超过固定振幅循环荷载,当振次≥9 000或振幅≥90 k Pa时,路堤坡顶法向累积变形超过固定振幅循环荷载;分级循环荷载作用下,路堤竖向和坡面法向累积变形均大于静载,加筋可有效减小分级循环荷载和静载作用下坡面法向累积变形差。展开更多
为探究土工格室加筋路堤在循环荷载及静载下的各种性能,利用美国GCTS公司的USTX-2000加载装置进行加载,通过改变加筋层数、格室高度,格室焊距对土工格室加筋路堤进行一系列模型试验。对各种工况下加筋路堤极限承载力、长期循环荷载及固...为探究土工格室加筋路堤在循环荷载及静载下的各种性能,利用美国GCTS公司的USTX-2000加载装置进行加载,通过改变加筋层数、格室高度,格室焊距对土工格室加筋路堤进行一系列模型试验。对各种工况下加筋路堤极限承载力、长期循环荷载及固定振次循环荷载后极限承载力的变化进行研究。试验表明,土工格室加筋能显著提高地基极限承载力并能显著减小坡顶和坡中临界破坏时的法向累积变形,在加筋间距一定的情况下,加筋层数增加和格室高度增大均可不同程度提高极限承载力并减小临界破坏时坡顶法向累积变形,格室焊距的减小也可在一定程度提高极限承载力,格室焊距对边坡法向变形影响不大;长期循环荷载下固定间距加筋层数对路堤竖向累积沉降量影响不大,而对边坡坡顶法向累积变形有一定影响,格室高度增大和格室焊距减小均可不同程度减小路堤竖向累积沉降量和坡面法向累积变形;越靠近加载点处,路堤土压力值受加筋影响越显著,加筋提高了土体刚度和密实度,使加筋路堤土压力值较无筋路堤明显增大;对于无筋路堤,改变动载幅值和振次均导致振后极限承载力有不同程度的降低,而对于加筋路堤,当动载幅值≥30 k Pa或动载振次≥1 000时,振后极限承载力均有不同程度的提高。展开更多
基金funding support from the National Natural Science Foundation of China(Grant Nos.52174092,and 51904290)open fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Anhui University of Science and Technology)(Grant No.JYBSYS202311).
文摘Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.
文摘目前对土工格室加筋路堤研究主要集中在静载条件下,动载条件下研究的比较少。为研究分级循环荷载下土工格室加筋路堤的力学性能,采用USTX-2000的动力加载装置进行加载,对土工格室加筋路堤在不同加筋层数、格室高度、格室焊距等工况下进行一系列模型试验。对分级循环荷载下路堤的竖向变形和坡面法向变形进行研究,并与固定振幅循环荷载及静载作用下的路堤进行对比分析,研究不同加载方案路堤力学性能的差异性。试验结果表明,土工格室加筋能显著提高路堤承受分级循环荷载的能力和减小竖向累积沉降量,在加筋间距一定的情况下,两层及以上加筋效果比单层加筋效果更显著,格室高度增大和格室焊距减小均可不同程度提高路堤承受分级循环荷载能力并减小竖向累积沉降量;加筋可减小路堤分级循环荷载下的坡面法向变形,格室高度增大和格室焊距减小在分级循环荷载幅值相同时均能减小坡顶和坡中处的法向累积变形;分级循环荷载作用下,当振次≥8 000或幅值≥80 k Pa时,路堤竖向累积沉降量超过固定振幅循环荷载,当振次≥9 000或振幅≥90 k Pa时,路堤坡顶法向累积变形超过固定振幅循环荷载;分级循环荷载作用下,路堤竖向和坡面法向累积变形均大于静载,加筋可有效减小分级循环荷载和静载作用下坡面法向累积变形差。
文摘为探究土工格室加筋路堤在循环荷载及静载下的各种性能,利用美国GCTS公司的USTX-2000加载装置进行加载,通过改变加筋层数、格室高度,格室焊距对土工格室加筋路堤进行一系列模型试验。对各种工况下加筋路堤极限承载力、长期循环荷载及固定振次循环荷载后极限承载力的变化进行研究。试验表明,土工格室加筋能显著提高地基极限承载力并能显著减小坡顶和坡中临界破坏时的法向累积变形,在加筋间距一定的情况下,加筋层数增加和格室高度增大均可不同程度提高极限承载力并减小临界破坏时坡顶法向累积变形,格室焊距的减小也可在一定程度提高极限承载力,格室焊距对边坡法向变形影响不大;长期循环荷载下固定间距加筋层数对路堤竖向累积沉降量影响不大,而对边坡坡顶法向累积变形有一定影响,格室高度增大和格室焊距减小均可不同程度减小路堤竖向累积沉降量和坡面法向累积变形;越靠近加载点处,路堤土压力值受加筋影响越显著,加筋提高了土体刚度和密实度,使加筋路堤土压力值较无筋路堤明显增大;对于无筋路堤,改变动载幅值和振次均导致振后极限承载力有不同程度的降低,而对于加筋路堤,当动载幅值≥30 k Pa或动载振次≥1 000时,振后极限承载力均有不同程度的提高。
