Cast aluminum(Al)alloys,owing to their low density and high specific strength,offer significant advantages in the fabrication of complex,large-scale,or monolithic structural components across civilian,defense,and mili...Cast aluminum(Al)alloys,owing to their low density and high specific strength,offer significant advantages in the fabrication of complex,large-scale,or monolithic structural components across civilian,defense,and military sectors that are weight-sensitive,including transportation,aerospace,and underwater weaponry.However,a substantial portion of these alloys often exhibit pronounced hot tearing susceptibility(HTS)during casting,which not only detrimentally affects the quality and efficiency of industrial production but also limits their further development in high-tech applications.Therefore,a comprehensive and profound understanding of hot tearing behavior in cast Al alloys is essential.This review first analyzes the formation mechanisms of hot tearing,encompassing strength theory,liquid film theory,intergranular bridging theory,solidification shrinkage compensation theory,and relevant models,as well as the key factors governing its occurrence,including alloy composition,grain structure,casting parameters,and inclusions.It then introduces current research methods,ranging from simple evaluation and physical parameter-based approaches to in situ observation and numerical simulation,followed by a summary of newly proposed hot tearing criteria.Finally,it discusses the remaining scientific challenges and outlines future research directions.Particular emphasis is placed on recent advances in the hot tearing of cast Al alloys over the past decade.展开更多
The textures and microstructures of hot-and cold-rolled sheets of an AA 5454 aluminium alloy were studied,with special attention paid to comparing the texture development for the symmetric and asymmetric cold rolling....The textures and microstructures of hot-and cold-rolled sheets of an AA 5454 aluminium alloy were studied,with special attention paid to comparing the texture development for the symmetric and asymmetric cold rolling.Scanning electron microscopy with electron-backscatter diffraction was used to monitor the development of the microstructure in the differently deformed and additionally annealed samples.Details of the formations and transformations of individual texture components occurring during the rolling processes were observed and discussed.The average grain sizes,textures and mechanical properties were correlated and explained for the symmetric and asymmetric cold-rolled samples.The asymmetric rolling is beneficial in terms of deep drawability because it reduces the planar anisotropy of the annealed material due to the decrease of the Cube,Goss,rotated-Cube and η-fibre texture components and at the same time strengthens X1-and X2-fibre texture components which are shear texture components and improve deep drawability.During the asymmetric cold rolling,the temperature increases due to friction,triggering recrystallisation processes and leading to larger grains.It is also confirmed that asymmetric cold rolling uses less rolling force and consequently less energy to produce a final material with better formability,particularly earing.展开更多
The effect of Cr addition on nickel aluminium bronze(NAB)alloy microstructure,mechanical properties,and erosion-corrosion behaviour has been studied.The results show that Cr addition does not change the composition of...The effect of Cr addition on nickel aluminium bronze(NAB)alloy microstructure,mechanical properties,and erosion-corrosion behaviour has been studied.The results show that Cr addition does not change the composition of the precipitated phases,more Cr entered theκphase and a small amount of Cr solubilized in the matrix,which increase the hardness of theκand matrix and decrease the potential difference between theκand matrix.NAB alloy with Cr shows high erosion-corrosion resistance at high flow rate conditions,due to its lower phase potential difference and higher surface hardness.At the flow rate of 3 m·s^(-1),the corrosion rate is 0.076 mm·year^(-1),which is~20%lower than that of the unadded Cr sample.Moreover,the corrosion product film contains Cr_(2)O_(3)and Cr^(3+),which improves the densification of the film and raises alloy’s corrosion resistance with Cr addition.The combination of mechanical and corrosion resistant properties may qualify this alloy as a potential candidate material for sustainable and safe equipment.展开更多
A commentary on an anode-free cell design with electrochemically stable sodium borohydride solid electrolyte and pelletized aluminium current collector for sodium all-solid-state batteries is presented.First,the viabl...A commentary on an anode-free cell design with electrochemically stable sodium borohydride solid electrolyte and pelletized aluminium current collector for sodium all-solid-state batteries is presented.First,the viable strategies for implementing anode-free configuration utilizing solid-state electrolytes are briefly reviewed.Then,the remarkable work of Meng et al.on designing an anode-free sodium all-solid-state battery is elucidated.Finally,the significance of Meng’s work is discussed.展开更多
The microstructure and mechanical properties of ceramic coatings formed on 6063 aluminium alloy obtained in silicate-,borate- and aluminate-based electrolyte without and with nanoadditive Al2O3 and TiO2 by micro-arc o...The microstructure and mechanical properties of ceramic coatings formed on 6063 aluminium alloy obtained in silicate-,borate- and aluminate-based electrolyte without and with nanoadditive Al2O3 and TiO2 by micro-arc oxidation（MAO） were studied by scanning electron microscopy（SEM）,energy-dispersive X-ray spectroscopy（EDS）,X-ray diffraction（XRD）,microhardness and friction-abrasion tests,respectively.SEM results show that coatings with nanoadditive have less porosities than those without nanoadditive.XRD results reveal that nanoadditive-containing coatings contain more oxides compared with nanoadditive-free coatings in all cases,which are consistent with the EDS analysis.Mechanical properties tests show that nanoadditive Al2O3-containing coatings have higher microhardness values compared with the other coatings obtained in silicate-,borate- and aluminate-based electrolyte.On the other hand,nanoadditive has a positive effect on improving the wearing-resistance of MAO coatings in all cases.Furthermore,the borate-MAO coatings present an inferior anti-wearing property compared with the silicate- and aluminate-MAO coatings for both the nanoadditive-free and nanoadditive-containing coatings.展开更多
Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achie...Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achieved by adjusting the diameters of the upper roll and the bottom roll and was used to prepare hot-rolled thick plate of 5182 aluminium alloy. The shear deformation and plate shape control were experimentally studied. The experimental results show that asymmetrical rolling has a significant effect on metal deformation stream and can somehow refine microstructure and improve the uniformity of microstructure and properties. The asymmetrical rolling process can also reduce the rolling force. However, bending of rolling plate often happens during asymmetrical rolling process. The factors affecting the bending were discussed.展开更多
The influence of some additives on bulk density,phase composition,mechanical strength and thermal shock resistance of aluminium titanate （AT） ceramics was investigated.AT ceramics with different additives of MgO,SiO...The influence of some additives on bulk density,phase composition,mechanical strength and thermal shock resistance of aluminium titanate （AT） ceramics was investigated.AT ceramics with different additives of MgO,SiO2 and Fe2O3 were prepared by reaction sintering.Properties of AT ceramics were tested by using Archimedes,three-point bending and thermal cycling tests.It was found that additives of MgO,SiO2 and Fe2O3 or their compound additives are favorable to reduce the porosities of AT,enhance mechanical strength and thermal shock resistance.The role of additives can be rationalized in terms of promotion of sintering process,formation of new phases and influence on lattice constant c of AT ceramics.展开更多
Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visual...Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visualized material flow patterns, a three-dimensional model was developed to conduct the numerical simulation of the temperature profile and plastic material flow in friction stir welding. The calculated velocity contour of plastic flow in close proximity of the tool is generally consistent with the visualized results. As the tool rotation speed increases at a constant tool travel speed, the material flow near the pin gets stronger. The predicted shape and size of the weld nugget zone match with the experimentally measured ones.展开更多
Low frequency electromagnetic casting （LFEC） process with the application of an induction coil outside the conventional direct chill （DC） casting mould was used to prepare the flat ingot of 2524 alloy and the effe...Low frequency electromagnetic casting （LFEC） process with the application of an induction coil outside the conventional direct chill （DC） casting mould was used to prepare the flat ingot of 2524 alloy and the effect of electromagnetic field on the microstructure and macrosegregation of this alloy was systematically studied. The results show that the fiat ingot prepared by the LFEC process has a finer and more uniform as-cast microstructure and the grain morphology is transformed from dendrite and rosette-like to equiaxed structure. The LFEC process also shows a significant effect on macrosegregation, and with the application of electromagnetic field during casting process, the segregation in the centre of the ingot is obviously reduced. The mechanism of these effects was also discussed.展开更多
The effects of pre-stretching following solution treatment on the hardness and microstructures of aged 2524 aluminium alloy at 170 ℃ were studied.Ageing hardness values under different pre-stretching conditions were ...The effects of pre-stretching following solution treatment on the hardness and microstructures of aged 2524 aluminium alloy at 170 ℃ were studied.Ageing hardness values under different pre-stretching conditions were measured,and the corresponding microstructures were characterized by transmission electron microscopy（TEM）.The results show that compared with unstretched samples,the peak hardness is increased and the time to reach the peak hardness is reduced with the increase of pre-strain;the number density of S（Al2CuMg） phases is increased and the length is shortened in pre-stretched alloy.Additionally,the number density of GPB zones is decreased with the increase of pre-strain in peak-aged samples.When the pre-strain is up to 5%,S phases play the predominant contribution to the peak hardness.Fine and uniformly distributed S phases lead to a higher hardness than GPB zones together with S phases existing in conventionally aged 2524 alloy.展开更多
The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field ...The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field distributions of strain rate,stress,temperature and velocity of metal flow were obtained.The results are basically consistent with the experiment,which indicates that this method may successfully predict the defects in the actual extrusion process.展开更多
Fatigue characteristics of A7N01 aluminium alloy welded joint were investigated and a fatigue crack initiation life-based model was proposed. The difference of fatigue crack initiation life among base metal, weld meta...Fatigue characteristics of A7N01 aluminium alloy welded joint were investigated and a fatigue crack initiation life-based model was proposed. The difference of fatigue crack initiation life among base metal, weld metal and heat affected zone (HAZ) is slight. Furthermore, the ratio of fatigue crack initiation life (Ni) to fatigue life to failure(Nf) is a material dependent parameter, 26.32%, 40.21% and 60.67% for base metal, HAZ and weld metal, respectively. Total fatigue life predicted using the presented model is in good agreement with the experimental data and that using Basquin’s model. The observation results of fatigue fracture surfaces, using scanning electron microscope (SEM), demonstrate that fatigue crack initiates from smooth surface due to welding process for weld metal, blowhole in HAZ causes fatigue crack initiation, and the crushed second phase particles play an important part in fatigue crack initiation in base metal.展开更多
NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance...NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance during electrolysis in molten salt cryolite at 960 °C, but according to the analyses of phase compositions and microstructures through XRD, SEM/EDX and metallographic analysis, the metal in the anodes is preferentially corroded and many pores are produced on the anode surface after electrolysis. The preferential dissolution of Fe in the NiFe2O4 phase may lead to the non-uniform corrosion of NiFe2O4 grains. Moreover, a dense protective layer of NiFe2O4-NiAl2O4-FeAl2O4 is formed on the anode surface, which originates from the reaction of Al2O3 dissolved in the electrolyte with NiO or FeO, the annexation of NiFe2O4-NiAl2O4-FeAl2O4 to NiO and volume expansion. Thus, the dense NiFe2O4-NiAl2O4-FeAl2O4 layer inhibits the metal loss and ceramic-phase corrosion on the surface of the cermet inert anodes.展开更多
[Objective] This study aimed to investigate the immunological adjuvant function of aluminium phosphate and chicken IL-18 in NDV F gene vaccine. [Method] The vaccine （0.2 ml） containing aluminum phosphate adjuvant （...[Objective] This study aimed to investigate the immunological adjuvant function of aluminium phosphate and chicken IL-18 in NDV F gene vaccine. [Method] The vaccine （0.2 ml） containing aluminum phosphate adjuvant （90 μg）, pcDNA/F （200μg）, and pcDNA/chlL-18 （200 μg） was prepared. The 7 d old chick- ens to be tested were randomly divided into six groups （12 chickens in each group） and immunized through intramuscular injection with inactivated Newcastle disease vaccines, pcDNA/F＋pcDNA/chlL-18＋phosphate aluminum, pcDNA/F, pcDNA/F.＋pcDNA/ chlL-18, pcDNA/F＋aluminum phosphate, and physiological saline respectively; the secondary immunization was conducted with the same dose when the chickens were 21 d old. Their blood was sampled 0, 7, 14, 21, 28 d after first immunization. Anti- body titer was detected with ELISA and T cell transformation rate was measured with MIT. Experimental chicken will be challenged with 30 LD50 NDV virulence 28 d after first immunization. [Result] The survival rate of the chickens immunized with pcDNA/F＋aluminium phosphate＋pcDNA/chlL-18 achieved 8/12, higher than that of those immunized with pcDNA/F 4/12 and pcDNA/F＋pcDNA/chlL-18 （6/12）. The NDV antibody titer of the chickens immunized with pcDNA/F＋ aluminum phosphate, pcD- NA/F＋pcDNA/chlL-18 and pcDNA/F＋pcDNA/chlL-18＋aluminum phosphate is not differ- ent （P〉0.05）, but significantly lower than that of the chickens immunized with tradi- tional vaccine （P〈0.05）. The T cell transformation rate of the chickens immunized with pcDNA/F＋pcDNA/chlL-18＋aluminium phosphate was obviously higher than that of the chickens immunized with pcDNA/F （P〈0.05）. The T cell transformation rates of chickens immunized with pcDNA/F and the traditional vaccine showed no signifi- cant difference （P〉0.05）. [Conclusion] Combination of aluminium phosphate and pcD- NA/chlL-18 can significantly enhance the immune effect of NDV F gene vaccine.展开更多
基金financially supported by the National Natural Science Foundation of China(No.52475380)the inaugural Young Elite Scientists Sponsorship Program(Doctoral Student Special Plan)of the China Association for Science and Technology(CAST)。
文摘Cast aluminum(Al)alloys,owing to their low density and high specific strength,offer significant advantages in the fabrication of complex,large-scale,or monolithic structural components across civilian,defense,and military sectors that are weight-sensitive,including transportation,aerospace,and underwater weaponry.However,a substantial portion of these alloys often exhibit pronounced hot tearing susceptibility(HTS)during casting,which not only detrimentally affects the quality and efficiency of industrial production but also limits their further development in high-tech applications.Therefore,a comprehensive and profound understanding of hot tearing behavior in cast Al alloys is essential.This review first analyzes the formation mechanisms of hot tearing,encompassing strength theory,liquid film theory,intergranular bridging theory,solidification shrinkage compensation theory,and relevant models,as well as the key factors governing its occurrence,including alloy composition,grain structure,casting parameters,and inclusions.It then introduces current research methods,ranging from simple evaluation and physical parameter-based approaches to in situ observation and numerical simulation,followed by a summary of newly proposed hot tearing criteria.Finally,it discusses the remaining scientific challenges and outlines future research directions.Particular emphasis is placed on recent advances in the hot tearing of cast Al alloys over the past decade.
文摘The textures and microstructures of hot-and cold-rolled sheets of an AA 5454 aluminium alloy were studied,with special attention paid to comparing the texture development for the symmetric and asymmetric cold rolling.Scanning electron microscopy with electron-backscatter diffraction was used to monitor the development of the microstructure in the differently deformed and additionally annealed samples.Details of the formations and transformations of individual texture components occurring during the rolling processes were observed and discussed.The average grain sizes,textures and mechanical properties were correlated and explained for the symmetric and asymmetric cold-rolled samples.The asymmetric rolling is beneficial in terms of deep drawability because it reduces the planar anisotropy of the annealed material due to the decrease of the Cube,Goss,rotated-Cube and η-fibre texture components and at the same time strengthens X1-and X2-fibre texture components which are shear texture components and improve deep drawability.During the asymmetric cold rolling,the temperature increases due to friction,triggering recrystallisation processes and leading to larger grains.It is also confirmed that asymmetric cold rolling uses less rolling force and consequently less energy to produce a final material with better formability,particularly earing.
基金supported by Beijing Nova Program(No.20230484371)the National Key Research and Development Program of China(No.2021YFB3700700).
文摘The effect of Cr addition on nickel aluminium bronze(NAB)alloy microstructure,mechanical properties,and erosion-corrosion behaviour has been studied.The results show that Cr addition does not change the composition of the precipitated phases,more Cr entered theκphase and a small amount of Cr solubilized in the matrix,which increase the hardness of theκand matrix and decrease the potential difference between theκand matrix.NAB alloy with Cr shows high erosion-corrosion resistance at high flow rate conditions,due to its lower phase potential difference and higher surface hardness.At the flow rate of 3 m·s^(-1),the corrosion rate is 0.076 mm·year^(-1),which is~20%lower than that of the unadded Cr sample.Moreover,the corrosion product film contains Cr_(2)O_(3)and Cr^(3+),which improves the densification of the film and raises alloy’s corrosion resistance with Cr addition.The combination of mechanical and corrosion resistant properties may qualify this alloy as a potential candidate material for sustainable and safe equipment.
基金grateful for support from the National Natural Science Foundation of China(Nos.52472247,52172229,21401145)Fundamental Research Funds for the Central Universities(No.104972024KFYjc0079).
文摘A commentary on an anode-free cell design with electrochemically stable sodium borohydride solid electrolyte and pelletized aluminium current collector for sodium all-solid-state batteries is presented.First,the viable strategies for implementing anode-free configuration utilizing solid-state electrolytes are briefly reviewed.Then,the remarkable work of Meng et al.on designing an anode-free sodium all-solid-state battery is elucidated.Finally,the significance of Meng’s work is discussed.
基金Project(51371039)supported by the National Natural Science Foundation of China
文摘The microstructure and mechanical properties of ceramic coatings formed on 6063 aluminium alloy obtained in silicate-,borate- and aluminate-based electrolyte without and with nanoadditive Al2O3 and TiO2 by micro-arc oxidation（MAO） were studied by scanning electron microscopy（SEM）,energy-dispersive X-ray spectroscopy（EDS）,X-ray diffraction（XRD）,microhardness and friction-abrasion tests,respectively.SEM results show that coatings with nanoadditive have less porosities than those without nanoadditive.XRD results reveal that nanoadditive-containing coatings contain more oxides compared with nanoadditive-free coatings in all cases,which are consistent with the EDS analysis.Mechanical properties tests show that nanoadditive Al2O3-containing coatings have higher microhardness values compared with the other coatings obtained in silicate-,borate- and aluminate-based electrolyte.On the other hand,nanoadditive has a positive effect on improving the wearing-resistance of MAO coatings in all cases.Furthermore,the borate-MAO coatings present an inferior anti-wearing property compared with the silicate- and aluminate-MAO coatings for both the nanoadditive-free and nanoadditive-containing coatings.
基金Projects(51104043,51374067)supported by the National Natural Science Foundation of ChinaProject(2012CB619506)supported by the National Basic Research Program of ChinaProject(N120409002)supported by the Fundamental Research Funds for the Central Universities,China
文摘Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achieved by adjusting the diameters of the upper roll and the bottom roll and was used to prepare hot-rolled thick plate of 5182 aluminium alloy. The shear deformation and plate shape control were experimentally studied. The experimental results show that asymmetrical rolling has a significant effect on metal deformation stream and can somehow refine microstructure and improve the uniformity of microstructure and properties. The asymmetrical rolling process can also reduce the rolling force. However, bending of rolling plate often happens during asymmetrical rolling process. The factors affecting the bending were discussed.
基金Project(2009BAE80B01) supported by the Key Projects in the National Science and Technology Pillar Program During the11th Five-Year Plan Period,China
文摘The influence of some additives on bulk density,phase composition,mechanical strength and thermal shock resistance of aluminium titanate （AT） ceramics was investigated.AT ceramics with different additives of MgO,SiO2 and Fe2O3 were prepared by reaction sintering.Properties of AT ceramics were tested by using Archimedes,three-point bending and thermal cycling tests.It was found that additives of MgO,SiO2 and Fe2O3 or their compound additives are favorable to reduce the porosities of AT,enhance mechanical strength and thermal shock resistance.The role of additives can be rationalized in terms of promotion of sintering process,formation of new phases and influence on lattice constant c of AT ceramics.
基金Project (GZ583) supported by the Sino-German Center for Science Promotion
文摘Thin copper sheets as marker material were embedded into weld path of 2024 aluminium alloy plates and their final position after friction stir welding was examined by metallographic techniques. Referring to the visualized material flow patterns, a three-dimensional model was developed to conduct the numerical simulation of the temperature profile and plastic material flow in friction stir welding. The calculated velocity contour of plastic flow in close proximity of the tool is generally consistent with the visualized results. As the tool rotation speed increases at a constant tool travel speed, the material flow near the pin gets stronger. The predicted shape and size of the weld nugget zone match with the experimentally measured ones.
基金Projects(51104043,51374067)supported by the National Natural Science Foundation of ChinaProject(2012CB619506)supported by the National Basic Research Program of ChinaProject(N120409002)supported by the Fundamental Research Funds for the Central Universities,China
文摘Low frequency electromagnetic casting （LFEC） process with the application of an induction coil outside the conventional direct chill （DC） casting mould was used to prepare the flat ingot of 2524 alloy and the effect of electromagnetic field on the microstructure and macrosegregation of this alloy was systematically studied. The results show that the fiat ingot prepared by the LFEC process has a finer and more uniform as-cast microstructure and the grain morphology is transformed from dendrite and rosette-like to equiaxed structure. The LFEC process also shows a significant effect on macrosegregation, and with the application of electromagnetic field during casting process, the segregation in the centre of the ingot is obviously reduced. The mechanism of these effects was also discussed.
基金Project(51001022) supported by the National Natural Science Foundation of ChinaProject supported by Innovative Research Team in University of Liaoning Province,China
文摘The effects of pre-stretching following solution treatment on the hardness and microstructures of aged 2524 aluminium alloy at 170 ℃ were studied.Ageing hardness values under different pre-stretching conditions were measured,and the corresponding microstructures were characterized by transmission electron microscopy（TEM）.The results show that compared with unstretched samples,the peak hardness is increased and the time to reach the peak hardness is reduced with the increase of pre-strain;the number density of S（Al2CuMg） phases is increased and the length is shortened in pre-stretched alloy.Additionally,the number density of GPB zones is decreased with the increase of pre-strain in peak-aged samples.When the pre-strain is up to 5%,S phases play the predominant contribution to the peak hardness.Fine and uniformly distributed S phases lead to a higher hardness than GPB zones together with S phases existing in conventionally aged 2524 alloy.
基金Project (2009A080205003) supported by the Major Science and Technology Project of Guangdong Province,ChinaProject (30815009) supported by the Foundation of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body,China
文摘The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field distributions of strain rate,stress,temperature and velocity of metal flow were obtained.The results are basically consistent with the experiment,which indicates that this method may successfully predict the defects in the actual extrusion process.
文摘Fatigue characteristics of A7N01 aluminium alloy welded joint were investigated and a fatigue crack initiation life-based model was proposed. The difference of fatigue crack initiation life among base metal, weld metal and heat affected zone (HAZ) is slight. Furthermore, the ratio of fatigue crack initiation life (Ni) to fatigue life to failure(Nf) is a material dependent parameter, 26.32%, 40.21% and 60.67% for base metal, HAZ and weld metal, respectively. Total fatigue life predicted using the presented model is in good agreement with the experimental data and that using Basquin’s model. The observation results of fatigue fracture surfaces, using scanning electron microscope (SEM), demonstrate that fatigue crack initiates from smooth surface due to welding process for weld metal, blowhole in HAZ causes fatigue crack initiation, and the crushed second phase particles play an important part in fatigue crack initiation in base metal.
基金Project (2012FJ6123) supported by the Project of Science and Technology of Hunan Province,ChinaProject supported by Post-Doctoral Foundation of Central South University,China+1 种基金Project (CL12100) supported the Undergraduate Innovative Training of Central South University,ChinaProject (2282013bkso13) supported by Free Exploration Plan of Central South University,China
文摘NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance during electrolysis in molten salt cryolite at 960 °C, but according to the analyses of phase compositions and microstructures through XRD, SEM/EDX and metallographic analysis, the metal in the anodes is preferentially corroded and many pores are produced on the anode surface after electrolysis. The preferential dissolution of Fe in the NiFe2O4 phase may lead to the non-uniform corrosion of NiFe2O4 grains. Moreover, a dense protective layer of NiFe2O4-NiAl2O4-FeAl2O4 is formed on the anode surface, which originates from the reaction of Al2O3 dissolved in the electrolyte with NiO or FeO, the annexation of NiFe2O4-NiAl2O4-FeAl2O4 to NiO and volume expansion. Thus, the dense NiFe2O4-NiAl2O4-FeAl2O4 layer inhibits the metal loss and ceramic-phase corrosion on the surface of the cermet inert anodes.
文摘[Objective] This study aimed to investigate the immunological adjuvant function of aluminium phosphate and chicken IL-18 in NDV F gene vaccine. [Method] The vaccine （0.2 ml） containing aluminum phosphate adjuvant （90 μg）, pcDNA/F （200μg）, and pcDNA/chlL-18 （200 μg） was prepared. The 7 d old chick- ens to be tested were randomly divided into six groups （12 chickens in each group） and immunized through intramuscular injection with inactivated Newcastle disease vaccines, pcDNA/F＋pcDNA/chlL-18＋phosphate aluminum, pcDNA/F, pcDNA/F.＋pcDNA/ chlL-18, pcDNA/F＋aluminum phosphate, and physiological saline respectively; the secondary immunization was conducted with the same dose when the chickens were 21 d old. Their blood was sampled 0, 7, 14, 21, 28 d after first immunization. Anti- body titer was detected with ELISA and T cell transformation rate was measured with MIT. Experimental chicken will be challenged with 30 LD50 NDV virulence 28 d after first immunization. [Result] The survival rate of the chickens immunized with pcDNA/F＋aluminium phosphate＋pcDNA/chlL-18 achieved 8/12, higher than that of those immunized with pcDNA/F 4/12 and pcDNA/F＋pcDNA/chlL-18 （6/12）. The NDV antibody titer of the chickens immunized with pcDNA/F＋ aluminum phosphate, pcD- NA/F＋pcDNA/chlL-18 and pcDNA/F＋pcDNA/chlL-18＋aluminum phosphate is not differ- ent （P〉0.05）, but significantly lower than that of the chickens immunized with tradi- tional vaccine （P〈0.05）. The T cell transformation rate of the chickens immunized with pcDNA/F＋pcDNA/chlL-18＋aluminium phosphate was obviously higher than that of the chickens immunized with pcDNA/F （P〈0.05）. The T cell transformation rates of chickens immunized with pcDNA/F and the traditional vaccine showed no signifi- cant difference （P〉0.05）. [Conclusion] Combination of aluminium phosphate and pcD- NA/chlL-18 can significantly enhance the immune effect of NDV F gene vaccine.
