This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were prese...This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were presented.In this paper,we discuss the effects of disturbance forces and noises on the system,and summarize various analysis and modeling methods for these interferences,including the integral method,frequency domain analysis method,and magnitude evaluation method.By analyzing the impact of disturbances and noises on the system,the paper also summarizes the system’s performance under slight interferences.Additionally,we highlight current research difficulties in the field of DFACS noise analysis.Overall,this paper provides valuable insights into the modeling and analysis of disturbances and noises in DFACSs,and identifies key areas for future research.展开更多
The corrosion behaviors of zinc alloy （ZnAl4Cul） in 3.5% （mass fraction） NaCl, 7.3% （mass fraction） Na2SO4 and simulated acid rain solutions were investigated using electrochemical measurements. The potential no...The corrosion behaviors of zinc alloy （ZnAl4Cul） in 3.5% （mass fraction） NaCl, 7.3% （mass fraction） Na2SO4 and simulated acid rain solutions were investigated using electrochemical measurements. The potential noise during dry-wet cycle was monitored and analyzed by fast Fourier transform （FFT）, fast wavelet transform （FWT）, shot noise theory and stochastic theory. Cumulative probability curves of event frequency fn indicate that the corrosion events in the dry cycles are greater than those in the wet cycles. Uniform corrosion was observed in the NaCl solution compared with more localized corrosion in the Na2SO4 solution, which is evidenced by FWT and SEM. Conditional events generation rate r（t） for diffusion controlled reactions decreases with increasing the time. r（t） values for uniform corrosion and diffusion controlled process are the largest in the wet cycle in 3.5% NaCl solution. The values of r（t） for pitting corrosion in Na2SO4 solution are observed to become large during spraying periods, and r（t） for pitting corrosion has the largest value in the Na2SO4 solution. The intergranular corrosion of zinc is serious in simulated acid rain solution.展开更多
As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the inf...As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the influence of experimental noise of modal data on sensitivity-based damage detection methods. Different from the com- monly used random perturbation technique, the proposed technique is deduced directly by Moore-Pen＂ose generalized inverse of the sensitivity matrix, which does not only make the analysis process more efficient but also can analyze the influence of noise on both frequencies and mode shapes for three commonly used sensitivity-based damage detection methods in a similar way. A one-story portal frame is adopted to evaluate the efficiency of the proposed noise analysis technique.展开更多
This paper deals with internally generated noise of bioelectric amplifiers that are usually used for processing of bioelectric events. The main purpose of this paper is to present a procedure for analysis of the effec...This paper deals with internally generated noise of bioelectric amplifiers that are usually used for processing of bioelectric events. The main purpose of this paper is to present a procedure for analysis of the effects of internal noise generated by the active circuits and to evaluate the output noise of the author's new designed bioelectric amplifier that caused by internal effects to the amplifier circuit itself in order to compare it with the noise generated by conventional amplifiers. The obtained analysis results of internally generated noise showed that the total output noise of bioelectric active circuits does not increase when some of their resistors have a larger value. This behavior is caused by the different transfer functions for the signal and the respective noise sources associated with these resistors. Moreover, the new designed bioelectric amplifier has an output noise less than that for conventional amplifiers. The obtained analysis results were also experimentally verified and the final conclusions were drawn.展开更多
A dynamic finite element method combined with finite element mixed formula for contact problem is used to analyze the dynamic characteristics of gear system. Considering the stiffness excitation, error excitation and ...A dynamic finite element method combined with finite element mixed formula for contact problem is used to analyze the dynamic characteristics of gear system. Considering the stiffness excitation, error excitation and meshing shock excitation, the dynamic finite element model is established for the entire gear system which includes gears, shafts, bearings and gearbox housing. By the software of I-DEAS, the natural frequency, normal mode, dynamic time-domain response, frequency-domain response and one-third octave velocity grade structure borne noise of gear system are studied by the method of theoretical modal analysis and dynamic response analysis. The maximum values of vibration and structure borne noise are occurred at the mesh frequency of output grade gearing.展开更多
To analyze the security of two-step quantum direct communication protocol （QDCP） by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 （2003）042317] in collective-rotation noise channel, a...To analyze the security of two-step quantum direct communication protocol （QDCP） by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 （2003）042317] in collective-rotation noise channel, an excellent model of noise analysis is proposed. In the security analysis, the method of the entropy theory is introduced, and is compared with QDCP, an error rate point Qo（M ： （Q0, 1.0）） is given. In different noise levels, if Eve wants to obtain the same amount of information, the error rate Q is distinguishable. The larger the noise level ~ is, the larger the error rate Q is. When the noise level ~ is lower than 11%, the high error rate is 0.153 without eavesdropping. Lastly, the security of the proposed protocol is discussed. It turns out that the quantum channel will be safe when Q 〈 0.153. Similarly, if error rate Q〉 0.153 = Q0, eavesdropping information I 〉 1, which means that there exist eavesdroppers in the quantum channel, and the quantum channel will not be safe anymore.展开更多
A distributed feedback fiber laser （DFB FL） sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs ...A distributed feedback fiber laser （DFB FL） sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs an unbalanced Michelson interferometer to translate laser wavelength shifts induced by weak measurands into phase shifts. A digital phase generated carrier demodulation scheme is introduced to achieve ultra-high resolution interrogation. A detailed noise analysis of the system is presented, and it is shown that the system resolution is limited by the frequency noise of the DFB FL.展开更多
The chattering noise problem of reed switch sensor signal for Automatic Meter Reading system was analyzed experimentally under various types of external vibrations and shocks. The external vibration level amplitude wa...The chattering noise problem of reed switch sensor signal for Automatic Meter Reading system was analyzed experimentally under various types of external vibrations and shocks. The external vibration level amplitude was measured with an accelerometer. To apply for water flow measurement devices, the reed switch sensors should keep high reliability. But the measured digital meter data are occurred difference or errors by chattering noise. The reed switch contains chattering error by itself at the force equivalent position. The vibrations such as passing vehicle near to the reed switch installed location causes chattering. In order to reduce chattering error, most system uses just software methods, for example using digital filter algorithm and also statistical calibration methods. However software approaches were implemented for reducing chattering error, there has still generated chattering error due to external mechanical vibrations and magnetic field. The chattering errors can be reduced by changing leaf spring structure using mechanical hysteresis characteristics.展开更多
Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition...Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition (VMD) and Empirical Wavelet Transform (EWT) offer valuable support for studying signal components, they also present certain limitations. This article integrates the strengths of both methods and proposes an enhanced approach that integrates VMD into the frequency band division principle of EWT. Initially, the method decomposes the signal using VMD, determining the mode count based on residuals, and subsequently employs EWT decomposition based on this information. This addresses mode aliasing issues in the original method while capitalizing on VMD’s adaptability. Feasibility was confirmed through simulation signals and ultimately applied to noise signals from vibrators. Experimental results demonstrate that the improved method not only resolves EWT frequency band division challenges but also effectively decomposes signal components compared to the VMD method.展开更多
A new architecture of CMOS low voltage downconve rsion mixer is presented.With 1.452GHz LO input and 1.45GHz RF input,simulation results show that the conversion gain is 15dB,IIP3 is -4.5dBm,NF is 17dB,the maximum tra...A new architecture of CMOS low voltage downconve rsion mixer is presented.With 1.452GHz LO input and 1.45GHz RF input,simulation results show that the conversion gain is 15dB,IIP3 is -4.5dBm,NF is 17dB,the maximum transient power dissipation is 9.3mW,and DC power dissipation is 9.2mW.The mixer’s noise and linearity analyses are also presented.展开更多
Transient electromagnetic method (TEM),as a non-seismic geophysical exploration mainstream electromagnetic method,is widely used in oil,gas,mineral and other underground resources exploration areas. The coil sensor is...Transient electromagnetic method (TEM),as a non-seismic geophysical exploration mainstream electromagnetic method,is widely used in oil,gas,mineral and other underground resources exploration areas. The coil sensor is generally used to collect data. In view of the problems of incomplete information of the abnormal body and the data loss in the existing TEM single-component coil sensor,a three-component TEM coil sensor is designed. By analyzing the relationship between sensor sensitivity and coil structure parameters,the coil structure and turns are designed. By analyzing the frequency response characteristics of the TEM magnetic field sensor,the signal distortion is reduced by using the under-damped matching mode. By analyzing the distribution of various noise sources of the magnetic sensor,the appropriate amplifier is selected to reduce the background noise. Finally,a three-component TEM induction magnetic field sensor is designed. The weight of the sensor is controlled at 3.2 kg and the working frequency is 10 mHz-10 kHz. The background noises of X and Y components probably keep in 1.5×10^-8 V/ Hz and sensitivities are 8.4 and 9.8 nT/s,respectively,the background noise of vertical component is 2.1× 10^-7 V/ Hz and sensitivity is 18.5 nT/s. Compared with the existing single-component TEM receiving magnetic field sensor,the designed sensor realizes the signal acquisition of three components. Without too much increase in volume and total weight,it improves the sensitivity of the sensor and reduces the background noise,thus the signal-to-noise ratio (SNR) of the signal is improved.展开更多
The relation between generalized operators and operator-valued distributions is discussed so that these two viewpoints can be used alternatively to explain quantum fields.
Magnetometric resistivity(MMR)method is a new way to detect dam leakage.The coil sensor is generally used to collect data in geophysical exploration methods.Given the characteristics of accurate vector data requiremen...Magnetometric resistivity(MMR)method is a new way to detect dam leakage.The coil sensor is generally used to collect data in geophysical exploration methods.Given the characteristics of accurate vector data requirements and high sensitivity requirement,a three-component MMR air-core coil sensor is designed.Through the analysis of sensor sensitivity and coil structure parameters,the coil structure and turn number are designed.By analyzing the noise source of the sensor,a suitable amplifier is selected to reduce the background noise of the system.Through the analysis of the three-component non-orthogonal angles,the parameters of the non-orthogonal angles of the coils are corrected.Finally,a three-component MMR induction magnetic field sensor is designed.The volume of the sensor is controlled at 0.027 m 3.The background noise of X、Y and Z are 5.030435 nV/Hz@380 Hz and magnetic field sensitivities are 0.18995 pT/Hz@380 Hz.The three channels have good consistency,and the three-component nonorthogonal angles correction error of three components is controlled within 0.2%.展开更多
In order to reduce the hidden danger of noise which can be charactered by singularity spectrum, a new algorithm based on wavelet transform modulus maxima method was proposed. Singularity analysis is one of the most pr...In order to reduce the hidden danger of noise which can be charactered by singularity spectrum, a new algorithm based on wavelet transform modulus maxima method was proposed. Singularity analysis is one of the most promising new approaches for extracting noise hidden information from noisy time series . Because of singularity strength is hard to calculate accurately, a wavelet transform modulus maxima method was used to get singularity spectrum. The singularity spectrum of white noise and aluminium interconnection electromigration noise was calculated and analyzed. The experimental results show that the new algorithm is more accurate than tradition estimating algorithm. The proposed method is feasible and efficient.展开更多
This work elaborates a fast and robust structural health monitoring scheme for copying with aircraft structural fatigue.The type of noise in structural strain signals is determined by using a statistical analysis meth...This work elaborates a fast and robust structural health monitoring scheme for copying with aircraft structural fatigue.The type of noise in structural strain signals is determined by using a statistical analysis method,which can be regarded as a mixture of Gaussian-like(tiny hairy signals)and impulse-like noise(single signals with anomalous movements in peak and valley areas).Based on this,a least squares filtering method is employed to preprocess strain signals.To precisely eliminate noise or outliers in strain signals,we propose a novel variational model to generate step signals instead of strain ones.Expert judgments are employed to classify the generated signals.Based on the classification labels,whether the aircraft is structurally healthy is accurately judged.By taking the generated step count vectors and labels as an input,a discriminative neural network is proposed to realize automatic signal discrimination.The network output means whether the aircraft structure is healthy or not.Experimental results demonstrate that the proposed scheme is effective and efficient,as well as achieves more satisfactory results than other peers.展开更多
This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the...This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the penetrable data surface were used for noise prediction. The results showed that the three kinds of wave leading edge blades were effective in reducing the rotor-stator interaction tonal noise and also have a certain inhibitory effect on broadband noise. The A10W15 stator blade can effectively reduce broadband noise in the frequency range of 2200 - 4200 Hz. When the amplitude is increased to 20, the noise reduction effect is further enhanced. However, when the amplitude is increased to 30, the broadband noise reduction effect is no longer significant. Further research shows that the wave leading edge stator blades can significantly change the pressure fluctuation distribution on the leading edge and suction surface, which control the modal energy distribution. Finally, this paper analyzed multiple factors affecting the broadband noise reduction, such as the noise source cut-off and cut-on effect and correlation. The purpose of this paper is to explore the laws of the influence of wave leading edge blades on the duct noise of real fan, and to reveal its noise control mechanism. .展开更多
The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–ra...The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–rail interaction.Most previous wheel–rail noise analysis has been conducted to mitigate those noises.However,in this paper,the noise is analysed to estimate the adhesion condition at the wheel–rail contact interface in combination with the other methodologies applied for this purpose.The adhesion level changes with changes in operational and environmental factors.To accurately estimate the adhesion level,the influence of those factors is included in this study.The testing and verification of the methodology required an accurate test prototype of the roller rig.In general,such testing and verification involve complex experimental works required by the intricate nature of the adhesion process and the integration of the different subsystems(i.e.controller,traction,braking).To this end,a new reduced-scale roller rig is developed to study the adhesion between wheel and rail roller contact.The various stages involved in the development of such a complex mechatronics system are described in this paper.Furthermore,the proposed brake control system was validated using the test rig under various adhesion conditions.The results indicate that the proposed brake controller has achieved a shorter stopping distance as compared to the conventional brake controller,and the brake control algorithm was able to maintain the operational condition even at the abrupt changes in adhesion condition.展开更多
Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value...Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value of the device is extracted and evaluated by several estimation techniques. However, these assessed values of V<sub>TH</sub> diverge from the exact values due to various short channel effects (SCEs) and non-idealities present in the device. Numerous prevalent V<sub>TH</sub> extraction methods are discussed. All the results are verified by extensive 2-D TCAD simulation and confirmed through analytical results at 10-nm technology node. Aim of this research paper is to explore and present a comparative study of largely applied threshold extraction methods for bulk driven nano-MOSFETs especially at 10-nm technology node along with various sub 45-nm technology nodes. Application of the threshold extraction methods to implement noise analysis is briefly presented to infer the most appropriate extraction method at nanometer technology nodes.展开更多
The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of...The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of a systematic nature, which can significantly affect the reliability of the obtained velocity estimates. This research shows that using non-classical error theory of measurement(NETM)for processing GNSS time series allows detecting the presence of weak, not removed from GNSS processing, sources of systematic errors. Based on the coordinate time series of selected permanent GNSS stations in Europe, we checked the empirical distributions of errors by the NETM on G. Jeffries’ recommendations and on the principles of the theory of hypothesis tests according to Pearson’s criterion. It is established that the obtained coordinates time series of GNSS-stations only partially confirm the hypothesis of their conformity to the normal Gaussian distribution law, and this may be the main reason for their unrepresentative classification. In the future, it is necessary to identify and take into account the causes of residual errors that distort the real distribution of the results of the GNSS time series.展开更多
基金This research was supported by National Key R&D Program of China:Gravitational Wave Detection Project(Nos.2021YFC2202601,2021YFC2202603)National Natural Science Foundation of China(No.12172288).
文摘This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were presented.In this paper,we discuss the effects of disturbance forces and noises on the system,and summarize various analysis and modeling methods for these interferences,including the integral method,frequency domain analysis method,and magnitude evaluation method.By analyzing the impact of disturbances and noises on the system,the paper also summarizes the system’s performance under slight interferences.Additionally,we highlight current research difficulties in the field of DFACS noise analysis.Overall,this paper provides valuable insights into the modeling and analysis of disturbances and noises in DFACSs,and identifies key areas for future research.
基金Projects (51131005, 51171172, J0830413) supported by the National Natural Science Foundation of ChinaProject (Y4110074) supported by Zhejiang Provincial Natural Science Foundation, China
文摘The corrosion behaviors of zinc alloy （ZnAl4Cul） in 3.5% （mass fraction） NaCl, 7.3% （mass fraction） Na2SO4 and simulated acid rain solutions were investigated using electrochemical measurements. The potential noise during dry-wet cycle was monitored and analyzed by fast Fourier transform （FFT）, fast wavelet transform （FWT）, shot noise theory and stochastic theory. Cumulative probability curves of event frequency fn indicate that the corrosion events in the dry cycles are greater than those in the wet cycles. Uniform corrosion was observed in the NaCl solution compared with more localized corrosion in the Na2SO4 solution, which is evidenced by FWT and SEM. Conditional events generation rate r（t） for diffusion controlled reactions decreases with increasing the time. r（t） values for uniform corrosion and diffusion controlled process are the largest in the wet cycle in 3.5% NaCl solution. The values of r（t） for pitting corrosion in Na2SO4 solution are observed to become large during spraying periods, and r（t） for pitting corrosion has the largest value in the Na2SO4 solution. The intergranular corrosion of zinc is serious in simulated acid rain solution.
基金Project supported jointly by the National Natural Science Foundation of China (No.50608036)the Innovative Funding of the Ministry of Water Resources of China (No. SCX2003-18)
文摘As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the influence of experimental noise of modal data on sensitivity-based damage detection methods. Different from the com- monly used random perturbation technique, the proposed technique is deduced directly by Moore-Pen＂ose generalized inverse of the sensitivity matrix, which does not only make the analysis process more efficient but also can analyze the influence of noise on both frequencies and mode shapes for three commonly used sensitivity-based damage detection methods in a similar way. A one-story portal frame is adopted to evaluate the efficiency of the proposed noise analysis technique.
文摘This paper deals with internally generated noise of bioelectric amplifiers that are usually used for processing of bioelectric events. The main purpose of this paper is to present a procedure for analysis of the effects of internal noise generated by the active circuits and to evaluate the output noise of the author's new designed bioelectric amplifier that caused by internal effects to the amplifier circuit itself in order to compare it with the noise generated by conventional amplifiers. The obtained analysis results of internally generated noise showed that the total output noise of bioelectric active circuits does not increase when some of their resistors have a larger value. This behavior is caused by the different transfer functions for the signal and the respective noise sources associated with these resistors. Moreover, the new designed bioelectric amplifier has an output noise less than that for conventional amplifiers. The obtained analysis results were also experimentally verified and the final conclusions were drawn.
基金Funded by the Natural Science Foundation of China (No. 50675232)the Natural Science Foundation of CQ CSTC (2006BB3008)
文摘A dynamic finite element method combined with finite element mixed formula for contact problem is used to analyze the dynamic characteristics of gear system. Considering the stiffness excitation, error excitation and meshing shock excitation, the dynamic finite element model is established for the entire gear system which includes gears, shafts, bearings and gearbox housing. By the software of I-DEAS, the natural frequency, normal mode, dynamic time-domain response, frequency-domain response and one-third octave velocity grade structure borne noise of gear system are studied by the method of theoretical modal analysis and dynamic response analysis. The maximum values of vibration and structure borne noise are occurred at the mesh frequency of output grade gearing.
基金Supported by the National Natural Science Foundation of China under Grant Nos 61472048,61402058,61272511,61472046,61202082 and 61370194the Beijing Natural Science Foundation under Grant No 4152038the China Postdoctoral Science Foundation Funded Project under Grant No 2014M561826
文摘To analyze the security of two-step quantum direct communication protocol （QDCP） by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 （2003）042317] in collective-rotation noise channel, an excellent model of noise analysis is proposed. In the security analysis, the method of the entropy theory is introduced, and is compared with QDCP, an error rate point Qo（M ： （Q0, 1.0）） is given. In different noise levels, if Eve wants to obtain the same amount of information, the error rate Q is distinguishable. The larger the noise level ~ is, the larger the error rate Q is. When the noise level ~ is lower than 11%, the high error rate is 0.153 without eavesdropping. Lastly, the security of the proposed protocol is discussed. It turns out that the quantum channel will be safe when Q 〈 0.153. Similarly, if error rate Q〉 0.153 = Q0, eavesdropping information I 〉 1, which means that there exist eavesdroppers in the quantum channel, and the quantum channel will not be safe anymore.
基金supported by the National 863 Projects under Grant No. 2007AA03Z415.
文摘A distributed feedback fiber laser （DFB FL） sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs an unbalanced Michelson interferometer to translate laser wavelength shifts induced by weak measurands into phase shifts. A digital phase generated carrier demodulation scheme is introduced to achieve ultra-high resolution interrogation. A detailed noise analysis of the system is presented, and it is shown that the system resolution is limited by the frequency noise of the DFB FL.
文摘The chattering noise problem of reed switch sensor signal for Automatic Meter Reading system was analyzed experimentally under various types of external vibrations and shocks. The external vibration level amplitude was measured with an accelerometer. To apply for water flow measurement devices, the reed switch sensors should keep high reliability. But the measured digital meter data are occurred difference or errors by chattering noise. The reed switch contains chattering error by itself at the force equivalent position. The vibrations such as passing vehicle near to the reed switch installed location causes chattering. In order to reduce chattering error, most system uses just software methods, for example using digital filter algorithm and also statistical calibration methods. However software approaches were implemented for reducing chattering error, there has still generated chattering error due to external mechanical vibrations and magnetic field. The chattering errors can be reduced by changing leaf spring structure using mechanical hysteresis characteristics.
文摘Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition (VMD) and Empirical Wavelet Transform (EWT) offer valuable support for studying signal components, they also present certain limitations. This article integrates the strengths of both methods and proposes an enhanced approach that integrates VMD into the frequency band division principle of EWT. Initially, the method decomposes the signal using VMD, determining the mode count based on residuals, and subsequently employs EWT decomposition based on this information. This addresses mode aliasing issues in the original method while capitalizing on VMD’s adaptability. Feasibility was confirmed through simulation signals and ultimately applied to noise signals from vibrators. Experimental results demonstrate that the improved method not only resolves EWT frequency band division challenges but also effectively decomposes signal components compared to the VMD method.
文摘A new architecture of CMOS low voltage downconve rsion mixer is presented.With 1.452GHz LO input and 1.45GHz RF input,simulation results show that the conversion gain is 15dB,IIP3 is -4.5dBm,NF is 17dB,the maximum transient power dissipation is 9.3mW,and DC power dissipation is 9.2mW.The mixer’s noise and linearity analyses are also presented.
文摘Transient electromagnetic method (TEM),as a non-seismic geophysical exploration mainstream electromagnetic method,is widely used in oil,gas,mineral and other underground resources exploration areas. The coil sensor is generally used to collect data. In view of the problems of incomplete information of the abnormal body and the data loss in the existing TEM single-component coil sensor,a three-component TEM coil sensor is designed. By analyzing the relationship between sensor sensitivity and coil structure parameters,the coil structure and turns are designed. By analyzing the frequency response characteristics of the TEM magnetic field sensor,the signal distortion is reduced by using the under-damped matching mode. By analyzing the distribution of various noise sources of the magnetic sensor,the appropriate amplifier is selected to reduce the background noise. Finally,a three-component TEM induction magnetic field sensor is designed. The weight of the sensor is controlled at 3.2 kg and the working frequency is 10 mHz-10 kHz. The background noises of X and Y components probably keep in 1.5×10^-8 V/ Hz and sensitivities are 8.4 and 9.8 nT/s,respectively,the background noise of vertical component is 2.1× 10^-7 V/ Hz and sensitivity is 18.5 nT/s. Compared with the existing single-component TEM receiving magnetic field sensor,the designed sensor realizes the signal acquisition of three components. Without too much increase in volume and total weight,it improves the sensitivity of the sensor and reduces the background noise,thus the signal-to-noise ratio (SNR) of the signal is improved.
文摘The relation between generalized operators and operator-valued distributions is discussed so that these two viewpoints can be used alternatively to explain quantum fields.
文摘Magnetometric resistivity(MMR)method is a new way to detect dam leakage.The coil sensor is generally used to collect data in geophysical exploration methods.Given the characteristics of accurate vector data requirements and high sensitivity requirement,a three-component MMR air-core coil sensor is designed.Through the analysis of sensor sensitivity and coil structure parameters,the coil structure and turn number are designed.By analyzing the noise source of the sensor,a suitable amplifier is selected to reduce the background noise of the system.Through the analysis of the three-component non-orthogonal angles,the parameters of the non-orthogonal angles of the coils are corrected.Finally,a three-component MMR induction magnetic field sensor is designed.The volume of the sensor is controlled at 0.027 m 3.The background noise of X、Y and Z are 5.030435 nV/Hz@380 Hz and magnetic field sensitivities are 0.18995 pT/Hz@380 Hz.The three channels have good consistency,and the three-component nonorthogonal angles correction error of three components is controlled within 0.2%.
基金Foundation item: National Natural Science Foundation of China(No.60372072)
文摘In order to reduce the hidden danger of noise which can be charactered by singularity spectrum, a new algorithm based on wavelet transform modulus maxima method was proposed. Singularity analysis is one of the most promising new approaches for extracting noise hidden information from noisy time series . Because of singularity strength is hard to calculate accurately, a wavelet transform modulus maxima method was used to get singularity spectrum. The singularity spectrum of white noise and aluminium interconnection electromigration noise was calculated and analyzed. The experimental results show that the new algorithm is more accurate than tradition estimating algorithm. The proposed method is feasible and efficient.
文摘This work elaborates a fast and robust structural health monitoring scheme for copying with aircraft structural fatigue.The type of noise in structural strain signals is determined by using a statistical analysis method,which can be regarded as a mixture of Gaussian-like(tiny hairy signals)and impulse-like noise(single signals with anomalous movements in peak and valley areas).Based on this,a least squares filtering method is employed to preprocess strain signals.To precisely eliminate noise or outliers in strain signals,we propose a novel variational model to generate step signals instead of strain ones.Expert judgments are employed to classify the generated signals.Based on the classification labels,whether the aircraft is structurally healthy is accurately judged.By taking the generated step count vectors and labels as an input,a discriminative neural network is proposed to realize automatic signal discrimination.The network output means whether the aircraft structure is healthy or not.Experimental results demonstrate that the proposed scheme is effective and efficient,as well as achieves more satisfactory results than other peers.
文摘This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the penetrable data surface were used for noise prediction. The results showed that the three kinds of wave leading edge blades were effective in reducing the rotor-stator interaction tonal noise and also have a certain inhibitory effect on broadband noise. The A10W15 stator blade can effectively reduce broadband noise in the frequency range of 2200 - 4200 Hz. When the amplitude is increased to 20, the noise reduction effect is further enhanced. However, when the amplitude is increased to 30, the broadband noise reduction effect is no longer significant. Further research shows that the wave leading edge stator blades can significantly change the pressure fluctuation distribution on the leading edge and suction surface, which control the modal energy distribution. Finally, this paper analyzed multiple factors affecting the broadband noise reduction, such as the noise source cut-off and cut-on effect and correlation. The purpose of this paper is to explore the laws of the influence of wave leading edge blades on the duct noise of real fan, and to reveal its noise control mechanism. .
基金The authors greatly appreciate the financial support from the Rail Manufacturing Cooperative Research Centre(funded jointly by participating rail organisations and the Australian Federal Government’s Business Cooperative Research Centres Programme)through Project R1.7.1–“Estimation of adhesion conditions between wheels and rails for the development of advanced braking control systems”.
文摘The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–rail interaction.Most previous wheel–rail noise analysis has been conducted to mitigate those noises.However,in this paper,the noise is analysed to estimate the adhesion condition at the wheel–rail contact interface in combination with the other methodologies applied for this purpose.The adhesion level changes with changes in operational and environmental factors.To accurately estimate the adhesion level,the influence of those factors is included in this study.The testing and verification of the methodology required an accurate test prototype of the roller rig.In general,such testing and verification involve complex experimental works required by the intricate nature of the adhesion process and the integration of the different subsystems(i.e.controller,traction,braking).To this end,a new reduced-scale roller rig is developed to study the adhesion between wheel and rail roller contact.The various stages involved in the development of such a complex mechatronics system are described in this paper.Furthermore,the proposed brake control system was validated using the test rig under various adhesion conditions.The results indicate that the proposed brake controller has achieved a shorter stopping distance as compared to the conventional brake controller,and the brake control algorithm was able to maintain the operational condition even at the abrupt changes in adhesion condition.
文摘Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value of the device is extracted and evaluated by several estimation techniques. However, these assessed values of V<sub>TH</sub> diverge from the exact values due to various short channel effects (SCEs) and non-idealities present in the device. Numerous prevalent V<sub>TH</sub> extraction methods are discussed. All the results are verified by extensive 2-D TCAD simulation and confirmed through analytical results at 10-nm technology node. Aim of this research paper is to explore and present a comparative study of largely applied threshold extraction methods for bulk driven nano-MOSFETs especially at 10-nm technology node along with various sub 45-nm technology nodes. Application of the threshold extraction methods to implement noise analysis is briefly presented to infer the most appropriate extraction method at nanometer technology nodes.
文摘The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of a systematic nature, which can significantly affect the reliability of the obtained velocity estimates. This research shows that using non-classical error theory of measurement(NETM)for processing GNSS time series allows detecting the presence of weak, not removed from GNSS processing, sources of systematic errors. Based on the coordinate time series of selected permanent GNSS stations in Europe, we checked the empirical distributions of errors by the NETM on G. Jeffries’ recommendations and on the principles of the theory of hypothesis tests according to Pearson’s criterion. It is established that the obtained coordinates time series of GNSS-stations only partially confirm the hypothesis of their conformity to the normal Gaussian distribution law, and this may be the main reason for their unrepresentative classification. In the future, it is necessary to identify and take into account the causes of residual errors that distort the real distribution of the results of the GNSS time series.
