Unstable operating conditions such as surge could cause damage to both aerodynamic performance and structural integrity of a compression system.This paper addresses the critical issue of aerodynamic instability in com...Unstable operating conditions such as surge could cause damage to both aerodynamic performance and structural integrity of a compression system.This paper addresses the critical issue of aerodynamic instability in compressor design,particularly focusing on an axial-centrifugal combined compressor,a widely used yet underexplored configuration.An experimental investigation was conducted on a three-stage axial and one-stage centrifugal compressor(3A1C),using two pipe systems and employing fast-responding transducers to capture the dynamic instability process from choke condition to deep surge.Results reveal that at the design speed,3A1C enters deep surge directly,whereas at off-design speeds,it experiences rotating stall and mild surge across a wide mass flow range.Some special instability features in the combined compressor can be found in the steady state map and dynamic process.The characteristic curve of the first axial stage keeps a positive slope during the whole mass flow range at an off-design speed.The first stage could work stably on the stall characteristic curve because the centrifugal stage has stronger pressurization and plays a dominant role in global aerodynamic instability.Besides,rotating instability occurs at the first rotor tip and disappears as the back pressure increases,which is also rarely seen in a single-axial compressor.This is also related to the strong pressurization of the centrifugal stage.The findings of this paper will contribute to the understanding of aerodynamic instabilities in combined compressors.展开更多
The effects of Reynolds number on the compressor efficiency are investigated by tests on three highlyloaded 10-stage axial compressors.The tests are conducted by adjusting the inlet total pressure,and thus different R...The effects of Reynolds number on the compressor efficiency are investigated by tests on three highlyloaded 10-stage axial compressors.The tests are conducted by adjusting the inlet total pressure,and thus different Reynolds numbers are obtained.The results indicate that the compressor efficiency decreases when the Reynolds number decreases.Based on the test results,reasonable correlations between the Reynolds number and compressor efficiency for each of the three compressors are obtained.The comparison between the test result-deduced correlations and Wassell correlations indicates that the effects of Reynolds number on the efficiency predicted by the Wassell correlations are less than those obtained by the test result-deduced correlations.Owing to the complex loss models and flow behavior in highly-loaded multi-stage compressors,additional influence factors,including the tip clearance and the compressor inlet duct design,should be considered for performance correlations.Nevertheless,the Wassell correlations are valid for the tendency prediction of performance changes relating to the Reynolds number,while accurate correlations still largely depend on the specific test results.展开更多
A stability model for multi-stage compressor is developed on the basis of the eigenvalue approach.This model assumes that the unsteady flow field can be decomposed into pressure,vortex and entropy waves.Besides,a line...A stability model for multi-stage compressor is developed on the basis of the eigenvalue approach.This model assumes that the unsteady flow field can be decomposed into pressure,vortex and entropy waves.Besides,a linear cascade of blades is modeled by three-dimensional semi-actuator disk theory and the characteristics of steady flow field are also considered in the present model.The connection between the analytical solution for stator,rotor and gap can be established by applying mode matching approach,the relevant stability equation can be expressed in the form of matrix,while the compressor system stability can be judged by the imaginary part of the matrix eigenvalue.The capacity of the stall inception model to predict the stall inception point of multi-stage compressor is assessed against the experimental data of National Aeronautics and Space Administration(NASA) two stage fan.The theoretical results show that this model can predict the stall onset points of a two-stage fan at different operating speeds with a reasonable accuracy.展开更多
The optimum pressure ratio distribution of a multistage reciprocating compressor is presented based on the assumption, i.e. the inter stage cooling is perfect and there are no pressure losses. The optimization of the...The optimum pressure ratio distribution of a multistage reciprocating compressor is presented based on the assumption, i.e. the inter stage cooling is perfect and there are no pressure losses. The optimization of the two or three stage pressure ratio is analyzed in two cases of constant heat transfer rate for the inter cooler or constant inter stage inlet temperature, based on the minimum of the sum of theoretical compression power at each stage about a multi stage reciprocating compressor. Furthermore, with an example of two stage compressor the influence on the sum of the power of each stage is analyzed when practical pressure ratio deviates from the optimum value. It is obtained that under different cooling conditions the optimum pressure ratio distribution of the multi stage compression is various, and the change of the optimum pressure ratio within a small range has little influence on the sum of the power each stage. For the two stage compression, this range can be represented as ε 1=(0 96～1 06)ε 1j .展开更多
The application of machine learning for pyrite discrimination establishes a robust foundation for constructing the ore-forming history of multi-stage deposits;however,published models face challenges related to limite...The application of machine learning for pyrite discrimination establishes a robust foundation for constructing the ore-forming history of multi-stage deposits;however,published models face challenges related to limited,imbalanced datasets and oversampling.In this study,the dataset was expanded to approximately 500 samples for each type,including 508 sedimentary,573 orogenic gold,548 sedimentary exhalative(SEDEX)deposits,and 364 volcanogenic massive sulfides(VMS)pyrites,utilizing random forest(RF)and support vector machine(SVM)methodologies to enhance the reliability of the classifier models.The RF classifier achieved an overall accuracy of 99.8%,and the SVM classifier attained an overall accuracy of 100%.The model was evaluated by a five-fold cross-validation approach with 93.8%accuracy for the RF and 94.9%for the SVM classifier.These results demonstrate the strong feasibility of pyrite classification,supported by a relatively large,balanced dataset and high accuracy rates.The classifier was employed to reveal the genesis of the controversial Keketale Pb-Zn deposit in NW China,which has been inconclusive among SEDEX,VMS,or a SEDEX-VMS transition.Petrographic investigations indicated that the deposit comprises early fine-grained layered pyrite(Py1)and late recrystallized pyrite(Py2).The majority voting classified Py1 as the VMS type,with an accuracy of RF and SVM being 72.2%and 75%,respectively,and confirmed Py2 as an orogenic type with 74.3% and 77.1%accuracy,respectively.The new findings indicated that the Keketale deposit originated from a submarine VMS mineralization system,followed by late orogenic-type overprinting of metamorphism and deformation,which is consistent with the geological and geochemical observations.This study further emphasizes the advantages of Machine learning(ML)methods in accurately and directly discriminating the deposit types and reconstructing the formation history of multi-stage deposits.展开更多
A modal analysis method of the rotor-stator interactions in multistage compressors has been developed by LMFA. This method, based on a double modal decomposition of the flow over space and time, has been applied to nu...A modal analysis method of the rotor-stator interactions in multistage compressors has been developed by LMFA. This method, based on a double modal decomposition of the flow over space and time, has been applied to nu- merical and experimental results of the high-speed 3Y2-stage compressor CREATE based at LMFA, Lyon-France. It reveals the presence of a very strong rotor-stator interaction which completely drives the flow at casing behind all the rotors. This modal analysis method applied to an unsteady RANS simulation permits to calculate the en- ergy of the rotor-stator interactions and to plot energetic meridian maps to explain experimental results and to analyze the interaction in the whole machine.展开更多
The high proportion of uncertain distributed power sources and the access to large-scale random electric vehicle(EV)charging resources further aggravate the voltage fluctuation of the distribution network,and the exis...The high proportion of uncertain distributed power sources and the access to large-scale random electric vehicle(EV)charging resources further aggravate the voltage fluctuation of the distribution network,and the existing research has not deeply explored the EV active-reactive synergistic regulating characteristics,and failed to realize themulti-timescale synergistic control with other regulatingmeans,For this reason,this paper proposes amultilevel linkage coordinated optimization strategy to reduce the voltage deviation of the distribution network.Firstly,a capacitor bank reactive power compensation voltage control model and a distributed photovoltaic(PV)activereactive power regulationmodel are established.Additionally,an external characteristicmodel of EVactive-reactive power regulation is developed considering the four-quadrant operational characteristics of the EVcharger.Amultiobjective optimization model of the distribution network is then constructed considering the time-series coupling constraints of multiple types of voltage regulators.A multi-timescale control strategy is proposed by considering the impact of voltage regulators on active-reactive EV energy consumption and PV energy consumption.Then,a four-stage voltage control optimization strategy is proposed for various types of voltage regulators with multiple time scales.Themulti-objective optimization is solved with the improvedDrosophila algorithmto realize the power fluctuation control of the distribution network and themulti-stage voltage control optimization.Simulation results validate that the proposed voltage control optimization strategy achieves the coordinated control of decentralized voltage control resources in the distribution network.It effectively reduces the voltage deviation of the distribution network while ensuring the energy demand of EV users and enhancing the stability and economic efficiency of the distribution network.展开更多
Seismic data denoising is a critical process usually applied at various stages of the seismic processing workflow,as our ability to mitigate noise in seismic data affects the quality of our subsequent analyses.However...Seismic data denoising is a critical process usually applied at various stages of the seismic processing workflow,as our ability to mitigate noise in seismic data affects the quality of our subsequent analyses.However,finding an optimal balance between preserving seismic signals and effectively reducing seismic noise presents a substantial challenge.In this study,we introduce a multi-stage deep learning model,trained in a self-supervised manner,designed specifically to suppress seismic noise while minimizing signal leakage.This model operates as a patch-based approach,extracting overlapping patches from the noisy data and converting them into 1D vectors for input.It consists of two identical sub-networks,each configured differently.Inspired by the transformer architecture,each sub-network features an embedded block that comprises two fully connected layers,which are utilized for feature extraction from the input patches.After reshaping,a multi-head attention module enhances the model’s focus on significant features by assigning higher attention weights to them.The key difference between the two sub-networks lies in the number of neurons within their fully connected layers.The first sub-network serves as a strong denoiser with a small number of neurons,effectively attenuating seismic noise;in contrast,the second sub-network functions as a signal-add-back model,using a larger number of neurons to retrieve some of the signal that was not preserved in the output of the first sub-network.The proposed model produces two outputs,each corresponding to one of the sub-networks,and both sub-networks are optimized simultaneously using the noisy data as the label for both outputs.Evaluations conducted on both synthetic and field data demonstrate the model’s effectiveness in suppressing seismic noise with minimal signal leakage,outperforming some benchmark methods.展开更多
Although previous researchers have attempted to decipher ore genesis and mineralization in the Erdaokan Ag-Pb-Zn deposit,some uncertainties regarding the mineralization process and evolution of both ore-forming fluids...Although previous researchers have attempted to decipher ore genesis and mineralization in the Erdaokan Ag-Pb-Zn deposit,some uncertainties regarding the mineralization process and evolution of both ore-forming fluids and magnetite types still need to be addressed.In this study,we obtained new EPMA,LA-ICP-MS,and in situ Fe isotope data from magnetite from the Erdaokan deposit,in order to better understand the mineralization mechanism and evolution of both magnetite and the ore-forming fluids.Our results identified seven types of magnetite at Erdaokan:disseminated magnetite(Mag1),coarse-grained magnetite(Mag2a),radial magnetite(Mag2b),fragmented fine-grained magnetite(Mag2c),vermicular gel magnetite(Mag3a1 and Mag3a2),colloidal magnetite(Mag3b)and dark gray magnetite(Mag4).All of the magnetite types were hydrothermal in origin and generally low in Ti(<400 ppm)and Ni(<800 ppm),while being enriched in light Fe isotopes(δ^(56)Fe ranging from−1.54‰to−0.06‰).However,they exhibit different geochemical signatures and are thus classified into high-manganese magnetite(Mag1,MnO>5 wt%),low-silicon magnetite(Mag2a-c,SiO_(2)<1 wt%),high-silicon magnetite(Mag3a-b,SiO_(2)from 1 to 7 wt%)and high-silicon-manganese magnetite(Mag4,SiO_(2)>1 wt%,MnO>0.2 wt%),each being formed within distinct hydrothermal environments.Based on mineralogy,elemental geochemistry,Fe isotopes,temperature trends,TMg-mag and(Ti+V)vs.(Al+Mn)diagrams,we propose that the Erdaokan Ag-Pb-Zn deposit underwent multi-stage mineralization,which can be broken down into four stages and nine sub-stages.Mag1,Mag2a-c,Mag3a-b and Mag4 were formed during the first sub-stage of each of the four stages,respectively.Additionally,fluid mixing,cooling and depressurization boiling were identified as the main mechanisms for mineral precipitation.The enrichment of Ag was significantly enhanced by the superposition of multi-stage ore-forming hydrothermal fluids in the Erdaokan Ag-Pb-Zn deposit.展开更多
This paper presents a new criterion for determining the unloading points quantitatively and consistently in a multi-stage triaxial test.The radial strain gradient(RSG)is first introduced as an arc tangent function of ...This paper presents a new criterion for determining the unloading points quantitatively and consistently in a multi-stage triaxial test.The radial strain gradient(RSG)is first introduced as an arc tangent function of the rate of change of radial strain to time.RSG is observed to correlate closely with the stress state of a compressed sample,and reaches a horizontal asymptote as approaching failure.For a given rock type,RSG value at peak stress is almost the same,irrespective of the porosity and permeability.These findings lead to the development of RSG criterion:Unloading points can be precisely determined at the time when RSG reaches a pre-determined value that is a little smaller than or equal to the RSG at peak stress.The RSG criterion is validated against other criteria and the single-stage triaxial test on various types of rocks.Failure envelopes from the RSG criterion match well with those from single-stage tests.A practical procedure is recommended to use the RSG criterion:an unconfined compression or single-stage test is first conducted to determine the RSG at peak stress for one sample,the unloading point is then selected to be a value close to the RSG at peak stress,and the multi-stage test is finally performed on another sample using the pre-selected RSG unloading criterion.Generally,the RSG criterion is applicable for any type of rocks,especially brittle rocks,where other criteria are not suitable.Further,it can be practically implemented on the most available rock mechanical testing instruments.展开更多
A new hang-off system has been proposed to improve the security of risers in hang-off modes during typhoons.However,efficient anti-typhoon evacuation strategies have not been investigated.Optimiza-tion model and metho...A new hang-off system has been proposed to improve the security of risers in hang-off modes during typhoons.However,efficient anti-typhoon evacuation strategies have not been investigated.Optimiza-tion model and method for the anti-typhoon evacuation strategies should be researched.Therefore,multi-objective functions are proposed based on operation time,evacuation speed stability,and steering stability.An evacuation path model and a dynamic model of risers with the new hang-off system are developed for design variables and constraints.A multi-objective optimization model with high-dimensional variables and complex constraints is established.Finally,a three-stage optimization method based on genetic algorithm,least square method,and the penalty function method is proposed to solve the multi-objective optimization model.Optimization results show that the operation time can be reduced through operation parameter optimization,especially evacuation heading optimization.The optimal anti-typhoon strategy is evacuation with all risers suspended along a variable path when the direction angle is large,while evacuation with all risers suspended along a straight path at another di-rection angle.Besides,the influencing factors on anti-typhoon evacuation strategies indicate that the proposed optimization model and method have strong applicability to working conditions and remarkable optimization effects.展开更多
Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal perform...Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal performance,accounting for its inapplicability to meet the emission criteria of 0.1 mg P/L phosphate.In this study,we report that the oxalate modification can inhibit the passivation of nZVI and alter the multi-stage phosphate adsorption mechanism by changing the adsorption sites.As expected,the stronger antipassivation ability of oxalate modified nZVI(OX-nZVI)strongly favored its phosphate adsorption.Interestingly,the oxalate modification endowed the surface Fe(III)sites with the lowest chemisorption energy and the fastest phosphate adsorption ability than the other adsorption sites,by in situ forming a Fe(III)-phosphate-oxalate ternary complex,therefore enabling an advanced phosphate removal process.At an initial phosphate concentration of 1.00 mg P/L,pH of 6.0 and a dosage of 0.3 g/L of adsorbents,OX-nZVI exhibited faster phosphate removal rate(0.11 g/mg/min)and lower residual phosphate level(0.02 mg P/L)than nZVI(0.055 g/mg/min and 0.19 mg P/L).This study sheds light on the importance of site manipulation in the development of high-performance adsorbents,and offers a facile surface modification strategy to prepare superior iron-basedmaterials for advanced phosphate removal.展开更多
The effectiveness of horizontal well multi-stage and multi-cluster fracturing in the fractured soft coal seam roof for coalbed methane(CBM) extraction has been demonstrated.This study focuses on the geological charact...The effectiveness of horizontal well multi-stage and multi-cluster fracturing in the fractured soft coal seam roof for coalbed methane(CBM) extraction has been demonstrated.This study focuses on the geological characteristics of the No.5 and No.11 coal seams in the Hancheng Block,Ordos Basin,China.A multi-functional,variable-size rock sample mold capable of securing the wellbore was developed to simulate layered formations comprising strata of varying lithology and thicknesses.A novel segmented fracturing simulation method based on an expandable pipe plugging technique is proposed.Large-scale true triaxial experiments were conducted to investigate the effects of horizontal wellbore location,perforation strategy,roof lithology,and vertical stress difference on fracture propagation,hydraulic energy variation,and the stimulated reservoir volume in horizontal wells targeting the soft coal seam roof.The results indicate that bilateral downward perforation with a phase angle of 120° optimizes hydraulic energy conservation,reduces operational costs,enhances fracture formation,and prevents fracturing failure caused by coal powder generation and migration.This perforation mode is thus considered optimal for coal seam roof fracturing.When the roof consists of sandstone,each perforation cluster tends to initiate a single dominant fracture with a regular geometry.In contrast,hydraulic fractures formed in mudstone roofs display diverse morphology.Due to its high strength,the sandstone roof requires significantly higher pressure for crack initiation and propagation,whereas the mudstone roof,with its strong water sensitivity,exhibits lower fracturing pressures.To mitigate inter-cluster interference,cluster spacing in mudstone roofs should be greater than that in sandstone roofs.Horizontal wellbore placement critically influences fracturing effectiveness.For indirect fracturing in sandstone roofs,an optimal position is 25 mm away from the lithological interface.In contrast,the optimal location for indirect fracturing in mudstone roofs is directly at the lithological interface with the coal seam.Higher vertical stress coefficients lead to increased fractu ring pressures and promote vertical,layer-penetrating fractures.A coefficient of 0.5 is identified as optimal for achieving effective indirect fracturing.This study provides valuable insights for the design and optimization of staged fracturing in horizontal wells targeting crushed soft coal seam roofs.展开更多
An opti mization process is used to redesign blades of a high-pressure compressor.An artificial neural network (ANN) method is coupled to Navier-Stokes solvers and is applied to three different redesigns.A newrotor bl...An opti mization process is used to redesign blades of a high-pressure compressor.An artificial neural network (ANN) method is coupled to Navier-Stokes solvers and is applied to three different redesigns.A newrotor blade of a transonic compressor is designed by modifying thick,stacking line andinlet angle using a 3Dapproach,with a significant efficiencyi mprovement at the design point.The off-design behavior of this new compressor is also checked afterwards,which shows that the whole performance of the inlet stage is improved over a wide range of mass flow.The losses are reduced,proving the good performance of the opti mum.The whole results indicate that the opti mization method can find i mproved design and can be integrated in a design procedure.展开更多
Triangular Au-Ag framework nanostructures （TFN） were synthesized via a multi-step galvanic replacement reaction （MGRR） of single-crystalline triangular silver nanoplates in a chlorauric acid （HAuCl4） solution at...Triangular Au-Ag framework nanostructures （TFN） were synthesized via a multi-step galvanic replacement reaction （MGRR） of single-crystalline triangular silver nanoplates in a chlorauric acid （HAuCl4） solution at room temperature. The morphological, compositional, and crystal structural changes involved with reaction steps were analyzed by using transmission electron microscopy（TEM）, energy-dispersive X-ray spectrometry （EDX）, and X-ray diffraction. TEM combined with EDX and selected area electron diffraction confirmed the replacement of Ag with Au. The in-plane dipolar surface plasmon resonance （SPR） absorption band of the Ag nanoplates locating initially at around 700 nm gradually redshifted to 1 100 nm via a multi-stage replacement manner after 7 stages. The adding amount of HAuCl4 per stage influenced the average redshift value per stage, thus enabled a fine tuning of the in-plane dipolar band. A proposed formation mechanism of the original Ag nanoplates developing pores while growing Au nanoparticles covering this underlying structure at more reaction steps was confirmed by exploiting surface-enhanced Raman scattering （SERS）.展开更多
Sichuan Basin is one of the uppermost petroliferous basins in China. It experienced three evolutionary phases which were marine carbonate platform （Ediacaran to Late Triassic）, Indosinian-Yanshanian orogeny foreland...Sichuan Basin is one of the uppermost petroliferous basins in China. It experienced three evolutionary phases which were marine carbonate platform （Ediacaran to Late Triassic）, Indosinian-Yanshanian orogeny foreland basin （Late Triassic to Late Cretaceous） and uplift and tectonic modification （Late Cretaceous to Quaternary）. The present-day tectonics of the Sichuan Ba- sin and its periphery are characterized by three basic elements which are topography, basement type and surface structure, and two settings （plate margin and interior）. Therefore, be subdivided into five units which have different structure and tectonic history. The basin contains five different sets of source rocks with thickness up to 2 500 m. These source rocks were well preserved due to the presence of Middel-Lower Triassic evaporites （〉-200 m） and thick terrestrial sediments filling in the Indosinian-Yanshanian foreland basin （〉3 000 m）. The uplift and erosion since Late Cretaceous has significant influence on cross-strata migration and accumulation of oil and gas. The multi-phase evolution of the basin and its superimposed tectonic elements, good petroleum geologic conditions and diverse petroleum systems reveal its bright exploration prospects.展开更多
Springback of a SUS321 complex geometry part formed by the multi-stage rigid-flexible compound process was studied through numerical simulations and laboratory experiments in this work.The sensitivity analysis was pro...Springback of a SUS321 complex geometry part formed by the multi-stage rigid-flexible compound process was studied through numerical simulations and laboratory experiments in this work.The sensitivity analysis was provided to have an insight in the effect of the evaluated process parameters.Furthermore,in order to minimize the springback problem,an accurate springback simulation model of the part was established and validated.The effects of the element size and timesteps on springback model were further investigated.Results indicate that the custom mesh size is beneficial for the springback simulation,and the four timesteps are found suited for the springback analysis for the complex geometry part.Finally,a strategy for reducing the springback by changing the geometry of the blank is proposed.The optimal blank geometry is obtained and used for manufacturing the part.展开更多
A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision pr...A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision process, and contains a point-mass model for the dynamics of an aircraft and takes into account the decision maker＇s preferences under uncertain conditions. Considering an active opponent, the opponent＇s maneuvers can be modeled stochastically. The solution of multistage influence diagram can be obtained by converting the multistage influence diagram into a two-level optimization problem. The simulation results show the model is effective.展开更多
The mechanical behavior and microstructures of an Al-Zn-Mg-Cu-Cr aluminum alloy during multi-stage hot deformation were investigated by thermal stimulation test, optical microscopy, and transmission electron microscop...The mechanical behavior and microstructures of an Al-Zn-Mg-Cu-Cr aluminum alloy during multi-stage hot deformation were investigated by thermal stimulation test, optical microscopy, and transmission electron microscopy. The true stress vs true strain curves and the microstructure evolution of two hot deformation procedures were gained. The flow stress of the alloy studied decreases with increasing the deforming passes and declining the temperature, and the larger the temperature decline between adjacent stages, the larger the peak stress fall is. The stress-strain behavior mainly result from the dynamic recovery during deformation, the static recovery and recrystallization in the delay time, and the second phases precipitated from the matrix at high temperature.展开更多
基金supported by the National Science and Technology Major Project of China(Nos.2017-II-0004-0016 and J2019-I-0011-0011).
文摘Unstable operating conditions such as surge could cause damage to both aerodynamic performance and structural integrity of a compression system.This paper addresses the critical issue of aerodynamic instability in compressor design,particularly focusing on an axial-centrifugal combined compressor,a widely used yet underexplored configuration.An experimental investigation was conducted on a three-stage axial and one-stage centrifugal compressor(3A1C),using two pipe systems and employing fast-responding transducers to capture the dynamic instability process from choke condition to deep surge.Results reveal that at the design speed,3A1C enters deep surge directly,whereas at off-design speeds,it experiences rotating stall and mild surge across a wide mass flow range.Some special instability features in the combined compressor can be found in the steady state map and dynamic process.The characteristic curve of the first axial stage keeps a positive slope during the whole mass flow range at an off-design speed.The first stage could work stably on the stall characteristic curve because the centrifugal stage has stronger pressurization and plays a dominant role in global aerodynamic instability.Besides,rotating instability occurs at the first rotor tip and disappears as the back pressure increases,which is also rarely seen in a single-axial compressor.This is also related to the strong pressurization of the centrifugal stage.The findings of this paper will contribute to the understanding of aerodynamic instabilities in combined compressors.
文摘The effects of Reynolds number on the compressor efficiency are investigated by tests on three highlyloaded 10-stage axial compressors.The tests are conducted by adjusting the inlet total pressure,and thus different Reynolds numbers are obtained.The results indicate that the compressor efficiency decreases when the Reynolds number decreases.Based on the test results,reasonable correlations between the Reynolds number and compressor efficiency for each of the three compressors are obtained.The comparison between the test result-deduced correlations and Wassell correlations indicates that the effects of Reynolds number on the efficiency predicted by the Wassell correlations are less than those obtained by the test result-deduced correlations.Owing to the complex loss models and flow behavior in highly-loaded multi-stage compressors,additional influence factors,including the tip clearance and the compressor inlet duct design,should be considered for performance correlations.Nevertheless,the Wassell correlations are valid for the tendency prediction of performance changes relating to the Reynolds number,while accurate correlations still largely depend on the specific test results.
基金supported by the National Natural Science Foundation of China(Grant Nos.51576008&51236001)the National Basic Research Program of China(GrantNo.2012CB720201)+2 种基金Aeronautical Science Foundation of China(Grant No.2014ZB51018)the Collaborative Innovation Center for Advanced Aero-Engine of Chinathe Fundamental Research Funds for the Central Universities
文摘A stability model for multi-stage compressor is developed on the basis of the eigenvalue approach.This model assumes that the unsteady flow field can be decomposed into pressure,vortex and entropy waves.Besides,a linear cascade of blades is modeled by three-dimensional semi-actuator disk theory and the characteristics of steady flow field are also considered in the present model.The connection between the analytical solution for stator,rotor and gap can be established by applying mode matching approach,the relevant stability equation can be expressed in the form of matrix,while the compressor system stability can be judged by the imaginary part of the matrix eigenvalue.The capacity of the stall inception model to predict the stall inception point of multi-stage compressor is assessed against the experimental data of National Aeronautics and Space Administration(NASA) two stage fan.The theoretical results show that this model can predict the stall onset points of a two-stage fan at different operating speeds with a reasonable accuracy.
文摘The optimum pressure ratio distribution of a multistage reciprocating compressor is presented based on the assumption, i.e. the inter stage cooling is perfect and there are no pressure losses. The optimization of the two or three stage pressure ratio is analyzed in two cases of constant heat transfer rate for the inter cooler or constant inter stage inlet temperature, based on the minimum of the sum of theoretical compression power at each stage about a multi stage reciprocating compressor. Furthermore, with an example of two stage compressor the influence on the sum of the power of each stage is analyzed when practical pressure ratio deviates from the optimum value. It is obtained that under different cooling conditions the optimum pressure ratio distribution of the multi stage compression is various, and the change of the optimum pressure ratio within a small range has little influence on the sum of the power each stage. For the two stage compression, this range can be represented as ε 1=(0 96～1 06)ε 1j .
基金the National Key Research and Development Program of China(2021YFC2900300)the Natural Science Foundation of Guangdong Province(2024A1515030216)+2 种基金MOST Special Fund from State Key Laboratory of Geological Processes and Mineral Resources,China University of Geosciences(GPMR202437)the Guangdong Province Introduced of Innovative R&D Team(2021ZT09H399)the Third Xinjiang Scientific Expedition Program(2022xjkk1301).
文摘The application of machine learning for pyrite discrimination establishes a robust foundation for constructing the ore-forming history of multi-stage deposits;however,published models face challenges related to limited,imbalanced datasets and oversampling.In this study,the dataset was expanded to approximately 500 samples for each type,including 508 sedimentary,573 orogenic gold,548 sedimentary exhalative(SEDEX)deposits,and 364 volcanogenic massive sulfides(VMS)pyrites,utilizing random forest(RF)and support vector machine(SVM)methodologies to enhance the reliability of the classifier models.The RF classifier achieved an overall accuracy of 99.8%,and the SVM classifier attained an overall accuracy of 100%.The model was evaluated by a five-fold cross-validation approach with 93.8%accuracy for the RF and 94.9%for the SVM classifier.These results demonstrate the strong feasibility of pyrite classification,supported by a relatively large,balanced dataset and high accuracy rates.The classifier was employed to reveal the genesis of the controversial Keketale Pb-Zn deposit in NW China,which has been inconclusive among SEDEX,VMS,or a SEDEX-VMS transition.Petrographic investigations indicated that the deposit comprises early fine-grained layered pyrite(Py1)and late recrystallized pyrite(Py2).The majority voting classified Py1 as the VMS type,with an accuracy of RF and SVM being 72.2%and 75%,respectively,and confirmed Py2 as an orogenic type with 74.3% and 77.1%accuracy,respectively.The new findings indicated that the Keketale deposit originated from a submarine VMS mineralization system,followed by late orogenic-type overprinting of metamorphism and deformation,which is consistent with the geological and geochemical observations.This study further emphasizes the advantages of Machine learning(ML)methods in accurately and directly discriminating the deposit types and reconstructing the formation history of multi-stage deposits.
基金the CNRS and the company Snecma (SAFRAN) which support the compressor CREATE research program
文摘A modal analysis method of the rotor-stator interactions in multistage compressors has been developed by LMFA. This method, based on a double modal decomposition of the flow over space and time, has been applied to nu- merical and experimental results of the high-speed 3Y2-stage compressor CREATE based at LMFA, Lyon-France. It reveals the presence of a very strong rotor-stator interaction which completely drives the flow at casing behind all the rotors. This modal analysis method applied to an unsteady RANS simulation permits to calculate the en- ergy of the rotor-stator interactions and to plot energetic meridian maps to explain experimental results and to analyze the interaction in the whole machine.
基金funded by the State Grid Corporation Science and Technology Project(5108-202218280A-2-391-XG).
文摘The high proportion of uncertain distributed power sources and the access to large-scale random electric vehicle(EV)charging resources further aggravate the voltage fluctuation of the distribution network,and the existing research has not deeply explored the EV active-reactive synergistic regulating characteristics,and failed to realize themulti-timescale synergistic control with other regulatingmeans,For this reason,this paper proposes amultilevel linkage coordinated optimization strategy to reduce the voltage deviation of the distribution network.Firstly,a capacitor bank reactive power compensation voltage control model and a distributed photovoltaic(PV)activereactive power regulationmodel are established.Additionally,an external characteristicmodel of EVactive-reactive power regulation is developed considering the four-quadrant operational characteristics of the EVcharger.Amultiobjective optimization model of the distribution network is then constructed considering the time-series coupling constraints of multiple types of voltage regulators.A multi-timescale control strategy is proposed by considering the impact of voltage regulators on active-reactive EV energy consumption and PV energy consumption.Then,a four-stage voltage control optimization strategy is proposed for various types of voltage regulators with multiple time scales.Themulti-objective optimization is solved with the improvedDrosophila algorithmto realize the power fluctuation control of the distribution network and themulti-stage voltage control optimization.Simulation results validate that the proposed voltage control optimization strategy achieves the coordinated control of decentralized voltage control resources in the distribution network.It effectively reduces the voltage deviation of the distribution network while ensuring the energy demand of EV users and enhancing the stability and economic efficiency of the distribution network.
基金supported by the King Abdullah University of Science and Technology(KAUST)。
文摘Seismic data denoising is a critical process usually applied at various stages of the seismic processing workflow,as our ability to mitigate noise in seismic data affects the quality of our subsequent analyses.However,finding an optimal balance between preserving seismic signals and effectively reducing seismic noise presents a substantial challenge.In this study,we introduce a multi-stage deep learning model,trained in a self-supervised manner,designed specifically to suppress seismic noise while minimizing signal leakage.This model operates as a patch-based approach,extracting overlapping patches from the noisy data and converting them into 1D vectors for input.It consists of two identical sub-networks,each configured differently.Inspired by the transformer architecture,each sub-network features an embedded block that comprises two fully connected layers,which are utilized for feature extraction from the input patches.After reshaping,a multi-head attention module enhances the model’s focus on significant features by assigning higher attention weights to them.The key difference between the two sub-networks lies in the number of neurons within their fully connected layers.The first sub-network serves as a strong denoiser with a small number of neurons,effectively attenuating seismic noise;in contrast,the second sub-network functions as a signal-add-back model,using a larger number of neurons to retrieve some of the signal that was not preserved in the output of the first sub-network.The proposed model produces two outputs,each corresponding to one of the sub-networks,and both sub-networks are optimized simultaneously using the noisy data as the label for both outputs.Evaluations conducted on both synthetic and field data demonstrate the model’s effectiveness in suppressing seismic noise with minimal signal leakage,outperforming some benchmark methods.
基金financially supported by the Heilongjiang Provincial Key R&D Program Project(No.GA21A204)Heilongjiang Provincial Natural Science Foundation of China(No.LH2022D031)the Research Project of Heilongjiang Province Bureau of Geology and Mineral Resources(No.HKY202302).
文摘Although previous researchers have attempted to decipher ore genesis and mineralization in the Erdaokan Ag-Pb-Zn deposit,some uncertainties regarding the mineralization process and evolution of both ore-forming fluids and magnetite types still need to be addressed.In this study,we obtained new EPMA,LA-ICP-MS,and in situ Fe isotope data from magnetite from the Erdaokan deposit,in order to better understand the mineralization mechanism and evolution of both magnetite and the ore-forming fluids.Our results identified seven types of magnetite at Erdaokan:disseminated magnetite(Mag1),coarse-grained magnetite(Mag2a),radial magnetite(Mag2b),fragmented fine-grained magnetite(Mag2c),vermicular gel magnetite(Mag3a1 and Mag3a2),colloidal magnetite(Mag3b)and dark gray magnetite(Mag4).All of the magnetite types were hydrothermal in origin and generally low in Ti(<400 ppm)and Ni(<800 ppm),while being enriched in light Fe isotopes(δ^(56)Fe ranging from−1.54‰to−0.06‰).However,they exhibit different geochemical signatures and are thus classified into high-manganese magnetite(Mag1,MnO>5 wt%),low-silicon magnetite(Mag2a-c,SiO_(2)<1 wt%),high-silicon magnetite(Mag3a-b,SiO_(2)from 1 to 7 wt%)and high-silicon-manganese magnetite(Mag4,SiO_(2)>1 wt%,MnO>0.2 wt%),each being formed within distinct hydrothermal environments.Based on mineralogy,elemental geochemistry,Fe isotopes,temperature trends,TMg-mag and(Ti+V)vs.(Al+Mn)diagrams,we propose that the Erdaokan Ag-Pb-Zn deposit underwent multi-stage mineralization,which can be broken down into four stages and nine sub-stages.Mag1,Mag2a-c,Mag3a-b and Mag4 were formed during the first sub-stage of each of the four stages,respectively.Additionally,fluid mixing,cooling and depressurization boiling were identified as the main mechanisms for mineral precipitation.The enrichment of Ag was significantly enhanced by the superposition of multi-stage ore-forming hydrothermal fluids in the Erdaokan Ag-Pb-Zn deposit.
文摘This paper presents a new criterion for determining the unloading points quantitatively and consistently in a multi-stage triaxial test.The radial strain gradient(RSG)is first introduced as an arc tangent function of the rate of change of radial strain to time.RSG is observed to correlate closely with the stress state of a compressed sample,and reaches a horizontal asymptote as approaching failure.For a given rock type,RSG value at peak stress is almost the same,irrespective of the porosity and permeability.These findings lead to the development of RSG criterion:Unloading points can be precisely determined at the time when RSG reaches a pre-determined value that is a little smaller than or equal to the RSG at peak stress.The RSG criterion is validated against other criteria and the single-stage triaxial test on various types of rocks.Failure envelopes from the RSG criterion match well with those from single-stage tests.A practical procedure is recommended to use the RSG criterion:an unconfined compression or single-stage test is first conducted to determine the RSG at peak stress for one sample,the unloading point is then selected to be a value close to the RSG at peak stress,and the multi-stage test is finally performed on another sample using the pre-selected RSG unloading criterion.Generally,the RSG criterion is applicable for any type of rocks,especially brittle rocks,where other criteria are not suitable.Further,it can be practically implemented on the most available rock mechanical testing instruments.
基金supported by the National Natural Science Foundation of China(Grant No:52271300,52071337)National Key Research and Development Program of China(2022YFC2806501)+1 种基金High-tech Ship Research Projects Sponsored by MIIT(CBG2N21-4-25)Program for Changjiang Scholars and Innovative Research Team in University(Grant No.IRT14R58).
文摘A new hang-off system has been proposed to improve the security of risers in hang-off modes during typhoons.However,efficient anti-typhoon evacuation strategies have not been investigated.Optimiza-tion model and method for the anti-typhoon evacuation strategies should be researched.Therefore,multi-objective functions are proposed based on operation time,evacuation speed stability,and steering stability.An evacuation path model and a dynamic model of risers with the new hang-off system are developed for design variables and constraints.A multi-objective optimization model with high-dimensional variables and complex constraints is established.Finally,a three-stage optimization method based on genetic algorithm,least square method,and the penalty function method is proposed to solve the multi-objective optimization model.Optimization results show that the operation time can be reduced through operation parameter optimization,especially evacuation heading optimization.The optimal anti-typhoon strategy is evacuation with all risers suspended along a variable path when the direction angle is large,while evacuation with all risers suspended along a straight path at another di-rection angle.Besides,the influencing factors on anti-typhoon evacuation strategies indicate that the proposed optimization model and method have strong applicability to working conditions and remarkable optimization effects.
基金supported by the National Key Research and Development Program of China(Nos.2022YFA1205602,and 2023YFC3707801)the National Natural Science Foundation of China(Nos.U22A20402,22376073,21936003 and 22306119)China Postdoctoral Science Foundation(No.2023T160419).
文摘Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal performance,accounting for its inapplicability to meet the emission criteria of 0.1 mg P/L phosphate.In this study,we report that the oxalate modification can inhibit the passivation of nZVI and alter the multi-stage phosphate adsorption mechanism by changing the adsorption sites.As expected,the stronger antipassivation ability of oxalate modified nZVI(OX-nZVI)strongly favored its phosphate adsorption.Interestingly,the oxalate modification endowed the surface Fe(III)sites with the lowest chemisorption energy and the fastest phosphate adsorption ability than the other adsorption sites,by in situ forming a Fe(III)-phosphate-oxalate ternary complex,therefore enabling an advanced phosphate removal process.At an initial phosphate concentration of 1.00 mg P/L,pH of 6.0 and a dosage of 0.3 g/L of adsorbents,OX-nZVI exhibited faster phosphate removal rate(0.11 g/mg/min)and lower residual phosphate level(0.02 mg P/L)than nZVI(0.055 g/mg/min and 0.19 mg P/L).This study sheds light on the importance of site manipulation in the development of high-performance adsorbents,and offers a facile surface modification strategy to prepare superior iron-basedmaterials for advanced phosphate removal.
基金support from China National Natural Science Foundation (11672333)。
文摘The effectiveness of horizontal well multi-stage and multi-cluster fracturing in the fractured soft coal seam roof for coalbed methane(CBM) extraction has been demonstrated.This study focuses on the geological characteristics of the No.5 and No.11 coal seams in the Hancheng Block,Ordos Basin,China.A multi-functional,variable-size rock sample mold capable of securing the wellbore was developed to simulate layered formations comprising strata of varying lithology and thicknesses.A novel segmented fracturing simulation method based on an expandable pipe plugging technique is proposed.Large-scale true triaxial experiments were conducted to investigate the effects of horizontal wellbore location,perforation strategy,roof lithology,and vertical stress difference on fracture propagation,hydraulic energy variation,and the stimulated reservoir volume in horizontal wells targeting the soft coal seam roof.The results indicate that bilateral downward perforation with a phase angle of 120° optimizes hydraulic energy conservation,reduces operational costs,enhances fracture formation,and prevents fracturing failure caused by coal powder generation and migration.This perforation mode is thus considered optimal for coal seam roof fracturing.When the roof consists of sandstone,each perforation cluster tends to initiate a single dominant fracture with a regular geometry.In contrast,hydraulic fractures formed in mudstone roofs display diverse morphology.Due to its high strength,the sandstone roof requires significantly higher pressure for crack initiation and propagation,whereas the mudstone roof,with its strong water sensitivity,exhibits lower fracturing pressures.To mitigate inter-cluster interference,cluster spacing in mudstone roofs should be greater than that in sandstone roofs.Horizontal wellbore placement critically influences fracturing effectiveness.For indirect fracturing in sandstone roofs,an optimal position is 25 mm away from the lithological interface.In contrast,the optimal location for indirect fracturing in mudstone roofs is directly at the lithological interface with the coal seam.Higher vertical stress coefficients lead to increased fractu ring pressures and promote vertical,layer-penetrating fractures.A coefficient of 0.5 is identified as optimal for achieving effective indirect fracturing.This study provides valuable insights for the design and optimization of staged fracturing in horizontal wells targeting crushed soft coal seam roofs.
文摘An opti mization process is used to redesign blades of a high-pressure compressor.An artificial neural network (ANN) method is coupled to Navier-Stokes solvers and is applied to three different redesigns.A newrotor blade of a transonic compressor is designed by modifying thick,stacking line andinlet angle using a 3Dapproach,with a significant efficiencyi mprovement at the design point.The off-design behavior of this new compressor is also checked afterwards,which shows that the whole performance of the inlet stage is improved over a wide range of mass flow.The losses are reduced,proving the good performance of the opti mum.The whole results indicate that the opti mization method can find i mproved design and can be integrated in a design procedure.
基金Project(10804101)supported by the National Natural Science Foundation of ChinaProject(2007CB815102)supported by the National Basic Research Program of ChinaProject(2007B08007)supported by the Science and Technology Development Foundation of Chinese Academy of Engineering Physics,China
文摘Triangular Au-Ag framework nanostructures （TFN） were synthesized via a multi-step galvanic replacement reaction （MGRR） of single-crystalline triangular silver nanoplates in a chlorauric acid （HAuCl4） solution at room temperature. The morphological, compositional, and crystal structural changes involved with reaction steps were analyzed by using transmission electron microscopy（TEM）, energy-dispersive X-ray spectrometry （EDX）, and X-ray diffraction. TEM combined with EDX and selected area electron diffraction confirmed the replacement of Ag with Au. The in-plane dipolar surface plasmon resonance （SPR） absorption band of the Ag nanoplates locating initially at around 700 nm gradually redshifted to 1 100 nm via a multi-stage replacement manner after 7 stages. The adding amount of HAuCl4 per stage influenced the average redshift value per stage, thus enabled a fine tuning of the in-plane dipolar band. A proposed formation mechanism of the original Ag nanoplates developing pores while growing Au nanoparticles covering this underlying structure at more reaction steps was confirmed by exploiting surface-enhanced Raman scattering （SERS）.
基金supported by the National Basic Research Program of China (No. 2012CB214805)the National Natural Science Foundation of China (Nos. 41230313, 41402119, 2017JQ0025, 41472017, 41572111)
文摘Sichuan Basin is one of the uppermost petroliferous basins in China. It experienced three evolutionary phases which were marine carbonate platform （Ediacaran to Late Triassic）, Indosinian-Yanshanian orogeny foreland basin （Late Triassic to Late Cretaceous） and uplift and tectonic modification （Late Cretaceous to Quaternary）. The present-day tectonics of the Sichuan Ba- sin and its periphery are characterized by three basic elements which are topography, basement type and surface structure, and two settings （plate margin and interior）. Therefore, be subdivided into five units which have different structure and tectonic history. The basin contains five different sets of source rocks with thickness up to 2 500 m. These source rocks were well preserved due to the presence of Middel-Lower Triassic evaporites （〉-200 m） and thick terrestrial sediments filling in the Indosinian-Yanshanian foreland basin （〉3 000 m）. The uplift and erosion since Late Cretaceous has significant influence on cross-strata migration and accumulation of oil and gas. The multi-phase evolution of the basin and its superimposed tectonic elements, good petroleum geologic conditions and diverse petroleum systems reveal its bright exploration prospects.
基金Project(2014ZX04002041)supported by the National Science and Technology Major Project,ChinaProject(51175024)supported by the National Natural Science Foundation of China
文摘Springback of a SUS321 complex geometry part formed by the multi-stage rigid-flexible compound process was studied through numerical simulations and laboratory experiments in this work.The sensitivity analysis was provided to have an insight in the effect of the evaluated process parameters.Furthermore,in order to minimize the springback problem,an accurate springback simulation model of the part was established and validated.The effects of the element size and timesteps on springback model were further investigated.Results indicate that the custom mesh size is beneficial for the springback simulation,and the four timesteps are found suited for the springback analysis for the complex geometry part.Finally,a strategy for reducing the springback by changing the geometry of the blank is proposed.The optimal blank geometry is obtained and used for manufacturing the part.
文摘A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision process, and contains a point-mass model for the dynamics of an aircraft and takes into account the decision maker＇s preferences under uncertain conditions. Considering an active opponent, the opponent＇s maneuvers can be modeled stochastically. The solution of multistage influence diagram can be obtained by converting the multistage influence diagram into a two-level optimization problem. The simulation results show the model is effective.
基金supported by the National Key Basic Research and Development Program of China(No.G1999064908)
文摘The mechanical behavior and microstructures of an Al-Zn-Mg-Cu-Cr aluminum alloy during multi-stage hot deformation were investigated by thermal stimulation test, optical microscopy, and transmission electron microscopy. The true stress vs true strain curves and the microstructure evolution of two hot deformation procedures were gained. The flow stress of the alloy studied decreases with increasing the deforming passes and declining the temperature, and the larger the temperature decline between adjacent stages, the larger the peak stress fall is. The stress-strain behavior mainly result from the dynamic recovery during deformation, the static recovery and recrystallization in the delay time, and the second phases precipitated from the matrix at high temperature.
