Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLD...Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLDPEs)with comparable molecular weights but different short-chain branch(SCB)contents(ranging of 5-66 per 1000 carbon atoms)were modified via dynamic melt mixing using 2 wt% benzoyl peroxide at 145℃ and 50 r/min for 30 min.The influence of SCB content on the processability and structure of the resulting products was systematically investigated.All modified products exhibited good melt processability with melt flow rates(MFR)ranging from 0.46 g/10min to 1.07 g/10min.Products derived from low-SCB LLDPEs showed a lower MFR,higher cross-linking content,a larger number of long-chain branches,and a higher degree of benzoyl grafting.In contrast,those produced from high-SCB LLDPEs exhibited improved processability,reduced cross-linking,fewer long-chain branches,and lower benzoyl grafting levels.A detailed structural investigation of the soluble and insoluble fractions,which were separated using trichlorobenzene fractionation,was conducted to analyze the structural features of various modified products and demonstrate that the SCB content(i.e.,tertiary carbon density)significantly influences radical coupling during dynamic modification.Elevated tertiary carbon density,by introducing greater steric hindrance,suppresses radical coupling during dynamic modification,thereby reducing the efficiency of both crosslinking and peroxide fragment grafting.These findings provide new insights into the structure-reactivity relationships in peroxide-induced polyethylene modification and lay the foundation for tailoring material properties via dynamic processing.展开更多
During the hoisting process of the offshore substation,changes in the hoisting speed can affect the hoisting system.Therefore,this study set four different speed conditions for the lifting and lowering stages of the i...During the hoisting process of the offshore substation,changes in the hoisting speed can affect the hoisting system.Therefore,this study set four different speed conditions for the lifting and lowering stages of the installation process,and studied the impact of different lifting and lowering speeds on the hoisting system under the same environmental conditions through numerical simulation.The results show that during the lifting operation,as the lifting speed increases,the swing motion of the substation and the installation vessel tends to decrease,and the faster the hoisting speed,the more obvious the swing suppression of the substation and the installation vessel,and the smaller the fluctuation in the tension amplitude of the slings and mooring lines.In contrast,during the lowering operation,as the lowering speed increases,the swing motion of the substation and the installation vessel tends to increase,and the faster the lowering speed,the more obvious the swing amplification effect of the substation and the installation vessel.Therefore,during hoisting operations,increasing the lifting speed and reducing the lowering speed can mitigate the motion performance of the hoisting coupling system,reduce the tension amplitude variation of the sling and mooring,and ensure the smooth progress of the hoisting operation.展开更多
Electrocatalytic oxidation is a promising technology for wastewater treatment,but poor mass transfer and low current efficiency impaded its engineering applications.To address these issues,researchers have developed f...Electrocatalytic oxidation is a promising technology for wastewater treatment,but poor mass transfer and low current efficiency impaded its engineering applications.To address these issues,researchers have developed flow-through electrochemical reactors(FERs)primarily based on porous electrodes,where the pore structure significantly impacts the electrochemical reaction.Therefore,this study systematically investigated the impact of different pore sizes on the fluid dynamics,current potential distribution,mass transfer processes,and degradation performance of FERs.Computational Fluid Dynamics(CFD)results indicated that smaller pore sizes(10μm,30μm,and 60μm)significantly enhanced convective effects within the fluid,reduced short fluid paths and dead volume regions within the microchannels,and facilitated mass transfer processes.Additionally,smaller pore sizes were conducive to a uniform distribution of current density.Furthermore,Fe(CN)_(6)^(4−)oxidation experiments revealed that the current density at a pore size of 160μm was notably lower than that at 10μm,indicating slower mass transfer of Fe(CN)_(6)^(4−)within larger channels.Calculations based on experimental results demonstrated that the mass transfer rate at a pore size of 10μm was six times than that at 160μm,further confirming the enhancing effect of smaller pore sizes on the mass transfer process.Lastly,experiments on tetracycline degradation showed that at a residence time of 90 s,the removal efficiencies of tetracycline were 80%and 39.1%for porous electrodes with pore sizes of 10μm and 160μm,respectively,demonstrating the superior removal efficiency of smaller pore sizes for tetracycline degradation.展开更多
Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects s...Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.展开更多
The multi-scale modeling combined with the cohesive zone model(CZM)and the molecular dynamics(MD)method were preformed to simulate the crack propagation in NiTi shape memory alloys(SMAs).The metallographic microscope ...The multi-scale modeling combined with the cohesive zone model(CZM)and the molecular dynamics(MD)method were preformed to simulate the crack propagation in NiTi shape memory alloys(SMAs).The metallographic microscope and image processing technology were employed to achieve a quantitative grain size distribution of NiTi alloys so as to provide experimental data for molecular dynamics modeling at the atomic scale.Considering the size effect of molecular dynamics model on material properties,a reasonable modeling size was provided by taking into account three characteristic dimensions from the perspective of macro,meso,and micro scales according to the Buckinghamπtheorem.Then,the corresponding MD simulation on deformation and fracture behavior was investigated to derive a parameterized traction-separation(T-S)law,and then it was embedded into cohesive elements of finite element software.Thus,the crack propagation behavior in NiTi alloys was reproduced by the finite element method(FEM).The experimental results show that the predicted initiation fracture toughness is in good agreement with experimental data.In addition,it is found that the dynamics initiation fracture toughness increases with decreasing grain size and increasing loading velocity.展开更多
A model for dynamic frictionless contact between a viscoelastic body and foundation is considered.The viscoelastic constitutive law is assumed to be nonlinear and the contact is modelled with the normal compliance con...A model for dynamic frictionless contact between a viscoelastic body and foundation is considered.The viscoelastic constitutive law is assumed to be nonlinear and the contact is modelled with the normal compliance condition.We obtain the well-posedness using nonlinear semigroup theory arguments.Moreover,the exponential stability result of the solution is shown by using the energy method to produce a suitable Lyapunov function.展开更多
Strong long-wavelength laser pulses enable direct manipulation of atomic lattices for engineering novel quantum states in complex materials.Nonlinear coupling between two infrared-active phonon modes(TO_(1) and TO_(2)...Strong long-wavelength laser pulses enable direct manipulation of atomic lattices for engineering novel quantum states in complex materials.Nonlinear coupling between two infrared-active phonon modes(TO_(1) and TO_(2)),induced by intense terahertz light fields,significantly enhances the amplitude of the TO_(1) mode and facilitates ultrafast control of transient structural distortions.This light-induced distortion reduces the lattice thermal conductivity from 8.1 W·m^(-1)·K^(-1)to 3.0 W·m^(-1)·K^(-1).The reduction originates from the nonlinear coupling,which enhances anharmonic interactions in the lattice potential energy and substantially shortens the phonon lifetime(τ).This work demonstrates a strategy applicable to other perovskite materials and provides a framework for investigating light-induced electrical,optical,and thermodynamic phase transitions.展开更多
Data-driven process monitoring is an effective approach to assure safe operation of modern manufacturing and energy systems,such as thermal power plants being studied in this work.Industrial processes are inherently d...Data-driven process monitoring is an effective approach to assure safe operation of modern manufacturing and energy systems,such as thermal power plants being studied in this work.Industrial processes are inherently dynamic and need to be monitored using dynamic algorithms.Mainstream dynamic algorithms rely on concatenating current measurement with past data.This work proposes a new,alternative dynamic process monitoring algorithm,using dot product feature analysis(DPFA).DPFA computes the dot product of consecutive samples,thus naturally capturing the process dynamics through temporal correlation.At the same time,DPFA's online computational complexity is lower than not just existing dynamic algorithms,but also classical static algorithms(e.g.,principal component analysis and slow feature analysis).The detectability of the new algorithm is analyzed for three types of faults typically seen in process systems:sensor bias,process fault and gain change fault.Through experiments with a numerical example and real data from a thermal power plant,the DPFA algorithm is shown to be superior to the state-of-the-art methods,in terms of better monitoring performance(fault detection rate and false alarm rate)and lower computational complexity.展开更多
Under the paradigm of Industry 5.0,intelligent manufacturing transcends mere efficiency enhancement by emphasizing human-machine collaboration,where human expertise plays a central role in assembly processes.Despite a...Under the paradigm of Industry 5.0,intelligent manufacturing transcends mere efficiency enhancement by emphasizing human-machine collaboration,where human expertise plays a central role in assembly processes.Despite advancements in intelligent and digital technologies,assembly process design still heavily relies on manual knowledge reuse,and inefficiencies and inconsistent quality in process documentation are caused.To address the aforementioned issues,this paper proposes a knowledge push method of complex product assembly process design based on distillation model-based dynamically enhanced graph and Bayesian network.First,an initial knowledge graph is constructed using a BERT-BiLSTM-CRF model trained with integrated human expertise and a fine-tuned large language model.Then,a confidence-based dynamic weighted fusion strategy is employed to achieve dynamic incremental construction of the knowledge graph with low resource consumption.Subsequently,a Bayesian network model is constructed based on the relationships between assembly components,assembly features,and operations.Bayesian network reasoning is used to push assembly process knowledge under different design requirements.Finally,the feasibility of the Bayesian network construction method and the effectiveness of Bayesian network reasoning are verified through a specific example,significantly improving the utilization of assembly process knowledge and the efficiency of assembly process design.展开更多
The calculation of settling speed of coarse particles is firstly addressed,with accelerated Stokesian dynamics without adjustable parameters,in which far field force acting on the particle instead of particle velocity...The calculation of settling speed of coarse particles is firstly addressed,with accelerated Stokesian dynamics without adjustable parameters,in which far field force acting on the particle instead of particle velocity is chosen as dependent variables to consider inter-particle hydrodynamic interactions.The sedimentation of a simple cubic array of spherical particles is simulated and compared to the results available to verify and validate the numerical code and computational scheme.The improved method keeps the same computational cost of the order O(NlogN)as usual accelerated Stokesian dynamics does.Then,more realistic random suspension sedimentation is investigated with the help of Mont Carlo method.The computational results agree well with experimental fitting.Finally,the sedimentation of finer cohesive particle,which is often observed in estuary environment,is presented as a further application in coastal engineering.展开更多
Remote sensing imagery,due to its high altitude,presents inherent challenges characterized by multiple scales,limited target areas,and intricate backgrounds.These inherent traits often lead to increased miss and false...Remote sensing imagery,due to its high altitude,presents inherent challenges characterized by multiple scales,limited target areas,and intricate backgrounds.These inherent traits often lead to increased miss and false detection rates when applying object recognition algorithms tailored for remote sensing imagery.Additionally,these complexities contribute to inaccuracies in target localization and hinder precise target categorization.This paper addresses these challenges by proposing a solution:The YOLO-MFD model(YOLO-MFD:Remote Sensing Image Object Detection withMulti-scale Fusion Dynamic Head).Before presenting our method,we delve into the prevalent issues faced in remote sensing imagery analysis.Specifically,we emphasize the struggles of existing object recognition algorithms in comprehensively capturing critical image features amidst varying scales and complex backgrounds.To resolve these issues,we introduce a novel approach.First,we propose the implementation of a lightweight multi-scale module called CEF.This module significantly improves the model’s ability to comprehensively capture important image features by merging multi-scale feature information.It effectively addresses the issues of missed detection and mistaken alarms that are common in remote sensing imagery.Second,an additional layer of small target detection heads is added,and a residual link is established with the higher-level feature extraction module in the backbone section.This allows the model to incorporate shallower information,significantly improving the accuracy of target localization in remotely sensed images.Finally,a dynamic head attentionmechanism is introduced.This allows themodel to exhibit greater flexibility and accuracy in recognizing shapes and targets of different sizes.Consequently,the precision of object detection is significantly improved.The trial results show that the YOLO-MFD model shows improvements of 6.3%,3.5%,and 2.5%over the original YOLOv8 model in Precision,map@0.5 and map@0.5:0.95,separately.These results illustrate the clear advantages of the method.展开更多
Seismic data reconstruction can provide high-density sampling and regular input data for inversion and imaging,playing a crucial role in seismic data processing.In seismic data reconstruction,a common scenario involve...Seismic data reconstruction can provide high-density sampling and regular input data for inversion and imaging,playing a crucial role in seismic data processing.In seismic data reconstruction,a common scenario involves a significant distance between the source and the first receiver,which makes it unattainable to acquire near-offset data.A new workflow for seismic data extrapolation is proposed to address this issue,which is based on a multi-scale dynamic time warping(MS-DTW)algorithm.MS-DTW can accurately calculate the time-shift between two time series and is a robust method for predicting time-offset(t-x)domain data.Using the time-shift calculated by the MS-DTW as the basic input,predict the two-way traveltime(TWT)of other traces based on the TWT of the reference trace.Perform autoregressive polynomial fitting on TWT and extrapolate TWT based on the fitted polynomial coefficients.Extract amplitude information from the TWT curve,fit the amplitude curve,and extrapolate the amplitude using polynomial coefficients.The proposed workflow does not necessitate data conversion to other domains and does not require prior knowledge of underground geological information.It applies to both isotropic and anisotropic media.The effectiveness of the workflow was verified through synthetic data and field data.The results show that compared with the method of predictive painting based on local slope,this approach can accurately predict missing near-offset seismic signals and demonstrates good robustness to noise.展开更多
The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that...The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that discontinuous dynamic recrystallization（DDRX） is the predominant recrystallization mechanism at temperature higher than 1050 °C and strain rate lower than 0.01 s-1.Meanwhile,continuous dynamic recrystallization is the main mechanism observed at temperature below 1050 °C and strain rate above 0.01 s-1,mixed with a few DDRX grains.In addition,decreasing strain rate and increasing deformation temperature are found to facilitate the progress of DRX and refinement of grains in the Ti alloy in β forging process.展开更多
The absorbing process in isolating and coating process of α-olefin drag reducing polymer was studied by molecular dynamic simulation method, on basis of coating theory of α-olefin drag reducing polymer particles wit...The absorbing process in isolating and coating process of α-olefin drag reducing polymer was studied by molecular dynamic simulation method, on basis of coating theory of α-olefin drag reducing polymer particles with polyurethane as coating material. The distributions of sodium laurate, sodium dodeeyl sulfate, and sodium dodeeyl benzene sulfonate on the surface of α-olefin drag reducing polymer particles were almost the same, but the bending degrees of them were obviously different. The bending degree of SLA molecules was greater than those of the other two surfactant molecules. Simulation results of absorbing and accumulating structure showed that, though hydrophobie properties of surfactant molecules were almost the same, water density around long chain sulfonate sodium was bigger than that around alkyl sulfate sodium. This property goes against useful absorbing and accumulating on the surface of α-olefin drag reducing polymer particles; simulation results of interactions of different surfactant and multiple hydroxyl compounds on surface of particles showed that, interactions of different surfaetant and one kind of multiple hydroxyl compound were similar to those of one kind of surfaetant and different multiple hydroxyl compounds. These two contrast types of interactions also exhibited the differences of absorbing distribution and closing degrees to surface of particles. The sequence of closing degrees was derived from simulation; control step of addition polymerization interaction in coating process was absorbing mass transfer process, so the more closed to surface of particle the multiple hydroxyl compounds were, the easier interactions With isoeyanate were. Simulation results represented the compatibility relationship between surfactant and multiple hydroxyl compounds. The isolating and coating processes of α-olefin drag reducing polymer were further understood on molecule and atom level through above simulation research, and based on the simulation, a referenced theoretical basis was provided for practical optimal selection and experimental preparation of α-olefin drag reducing polymer particles suspension isolation agent.展开更多
In the research of parachute, canopy inflation process modeling is one of the most complicated tasks. As canopy often experiences the largest deformations and loa-dings during a very short time, it is of great difficu...In the research of parachute, canopy inflation process modeling is one of the most complicated tasks. As canopy often experiences the largest deformations and loa-dings during a very short time, it is of great difficulty for theoretical analysis and experimental measurements. In this paper, aerodynamic equations and structural dynamics equations were developed for describing parachute opening process, and an iterative coupling solving strategy incorpo- rating the above equations was proposed for a small-scale, flexible and flat-circular parachute. Then, analyses were carried out for canopy geometry, time-dependent pressure difference between the inside and outside of the canopy, transient vortex around the canopy and the flow field in the radial plane as a sequence in opening process. The mechanism of the canopy shape development was explained from perspective of transient flow fields during the inflation process. Experiments of the parachute opening process were conducted in a wind tunnel, in which instantaneous shape of the canopy was measured by high velocity camera and the opening loading was measured by dynamometer balance. The theoretical predictions were found in good agreement with the experimental results, validating the proposed approach. This numerical method can improve the situation of strong dependence of parachute research on wind tunnel tests, and is of significance to the understanding of the mechanics of parachute inflation process.展开更多
One of the assumptions of previous research in evolutionary game dynamics is that individuals use only one rule to update their strategy. In reality, an individual's strategy update rules may change with the envir...One of the assumptions of previous research in evolutionary game dynamics is that individuals use only one rule to update their strategy. In reality, an individual's strategy update rules may change with the environment, and it is possible for an individual to use two or more rules to update their strategy. We consider the case where an individual updates strategies based on the Moran and imitation processes, and establish mixed stochastic evolutionary game dynamics by combining both processes. Our aim is to study how individuals change strategies based on two update rules and how this affects evolutionary game dynamics. We obtain an analytic expression and properties of the fixation probability and fixation times(the unconditional fixation time or conditional average fixation time) associated with our proposed process. We find unexpected results. The fixation probability within the proposed model is independent of the probabilities that the individual adopts the imitation rule update strategy. This implies that the fixation probability within the proposed model is equal to that from the Moran and imitation processes. The one-third rule holds in the proposed mixed model. However, under weak selection, the fixation times are different from those of the Moran and imitation processes because it is connected with the probability that individuals adopt an imitation update rule. Numerical examples are presented to illustrate the relationships between fixation times and the probability that an individual adopts the imitation update rule, as well as between fixation times and selection intensity. From the simulated analysis, we find that the fixation time for a mixed process is greater than that of the Moran process, but is less than that of the imitation process. Moreover, the fixation times for a cooperator in the proposed process increase as the probability of adopting an imitation update increases; however, the relationship becomes more complex than a linear relationship.展开更多
In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firs...In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firstly investigated. During casting AZ31 alloy by this process, non-uniform microstructure distributions and non- equilibrium solidification region near the roll surface were found in the roll-shoe gap. Microstructural evolution from dendrite to rosette and spherical grains was observed during the casting by CSEP. Casting temperature, roll-shoe gap width and cooling ability have great effect on casting process and metal flow, so these factors should be carefully controlled, a proper casting temperature of 710-750℃ is suggested. The white α phases were strongly stretched during the processing, and the remnant liquids are correspondingly distributes along the solid phase boundaries and also show stripped lines.展开更多
The western coast of Hainan Island exhibits a savanna landscape. Many types of sand dunes, including transverse dune ridges, longitudinal dune ridges, elliptical dunes, coppice dunes, and climbing dunes, are widely di...The western coast of Hainan Island exhibits a savanna landscape. Many types of sand dunes, including transverse dune ridges, longitudinal dune ridges, elliptical dunes, coppice dunes, and climbing dunes, are widely distributed in the coastal zone. In winter, high-frequency and high-energy NE winds （dominant winds） are prevalent, with a resultant drift direction （RDD） of S35.6°W. In spring, low-frequency and low-energy SW secondary winds prevail, with a RDD of N25.1°E. Wind tunnel simulations revealed that the airflow over the dune surface is the main factor controlling the erosion and deposition patterns of dune surfaces and the morphological development of dunes. In the region＇s bidirectional wind environment, with two seasonally distinct energy levels, the airflow over the surface of elliptical dunes, barchan dunes, and transverse dune ridges will exhibit a transverse pattern, whereas the airflow over longitudinal dunes ridges exhibits a lateral pattern and that over climbing dunes exhibits a climbing-circumfluent pattern. These patterns represent different dynamic processes. The coastal dunes on the western coast of Hainan Island are influenced by factors such as onshore winds, sand sources, coastal slopes, rivers, and forest shelter belts. The source of the sand that supplements these dunes particularly influences the development pattern： when there is more sand, the pattern shows positive equilibrium deposition between dune ridges and dunes; otherwise, it shows negative equilibrium deposition. The presence or absence of forest shelter belts also influences deposition and dune development patterns and transformation of dune forms. Coastal dunes and inland desert dunes experience similar dynamic processes, but the former have more diversified shapes and more complex formation mechanisms.展开更多
For critical engineering systems such as aircraft and aerospace vehicles, accurate Remaining Useful Life(RUL) prediction not only means cost saving, but more importantly, is of great significance in ensuring system re...For critical engineering systems such as aircraft and aerospace vehicles, accurate Remaining Useful Life(RUL) prediction not only means cost saving, but more importantly, is of great significance in ensuring system reliability and preventing disaster. RUL is affected not only by a system's intrinsic deterioration, but also by the operational conditions under which the system is operating. This paper proposes an RUL prediction approach to estimate the mean RUL of a continuously degrading system under dynamic operational conditions and subjected to condition monitoring at short equi-distant intervals. The dynamic nature of the operational conditions is described by a discrete-time Markov chain, and their influences on the degradation signal are quantified by degradation rates and signal jumps in the degradation model. The uniqueness of our proposed approach is formulating the RUL prediction problem in a semi-Markov decision process framework, by which the system mean RUL can be obtained through the solution to a limited number of equations. To extend the use of our proposed approach in real applications, different failure standards according to different operational conditions are also considered. The application and effectiveness of this approach are illustrated by a turbofan engine dataset and a comparison with existing results for the same dataset.展开更多
Abstract The Nansha ultra-crust layer-block is confined by ultra-crustal boundary faults of distinctive features, bordering the Kangtai-Shuangzi-Xiongnan extensional faulted zone on the north, the Baxian-Baram-Yoca-Cu...Abstract The Nansha ultra-crust layer-block is confined by ultra-crustal boundary faults of distinctive features, bordering the Kangtai-Shuangzi-Xiongnan extensional faulted zone on the north, the Baxian-Baram-Yoca-Cuyo nappe faulted zone on the south, the Wan'an-Natuna strike-slip tensional faulted zone on the west and the Mondoro-Panay strike-slip compressive faulted zone on the east. These faults take the top of the Nansha asthenosphere as their common detachmental surface. The Cenozoic dynamic process of the ultra-crust layer-block can be divided into four stages: K2-E21, during which the northern boundary faults extended, this ultra-crust layer-block was separated from the South China-Indosinian continental margin, the Palaeo-South China Sea subducted southwards and the Sibu accretion wedge was formed; E22-E31, during which the Southwest sub-sea basin extended and orogeny was active due to the collision of the Sibu accretion wedge; E32-N11, during which the central sub-sea basin extended, the Miri accretion wedge was formed and “A-type” subduction of the southern margin of the north Balawan occurred; N12-the present, during which large-scale thrusting and napping of the boundary faults in the south and mountain-building have taken place and the South China Sea stopped its extension.展开更多
基金financially supported by the Science and Technology Project of PetroChina Company Limited,China(No.2022DJ6314)the National Natural Science Foundation of China(No.52173056)。
文摘Dynamic melt modification of polyethylene via the direct grafting of peroxide fragments shows promise for the development of processable functionalized materials.In this study,four linear low-density polyethylenes(LLDPEs)with comparable molecular weights but different short-chain branch(SCB)contents(ranging of 5-66 per 1000 carbon atoms)were modified via dynamic melt mixing using 2 wt% benzoyl peroxide at 145℃ and 50 r/min for 30 min.The influence of SCB content on the processability and structure of the resulting products was systematically investigated.All modified products exhibited good melt processability with melt flow rates(MFR)ranging from 0.46 g/10min to 1.07 g/10min.Products derived from low-SCB LLDPEs showed a lower MFR,higher cross-linking content,a larger number of long-chain branches,and a higher degree of benzoyl grafting.In contrast,those produced from high-SCB LLDPEs exhibited improved processability,reduced cross-linking,fewer long-chain branches,and lower benzoyl grafting levels.A detailed structural investigation of the soluble and insoluble fractions,which were separated using trichlorobenzene fractionation,was conducted to analyze the structural features of various modified products and demonstrate that the SCB content(i.e.,tertiary carbon density)significantly influences radical coupling during dynamic modification.Elevated tertiary carbon density,by introducing greater steric hindrance,suppresses radical coupling during dynamic modification,thereby reducing the efficiency of both crosslinking and peroxide fragment grafting.These findings provide new insights into the structure-reactivity relationships in peroxide-induced polyethylene modification and lay the foundation for tailoring material properties via dynamic processing.
基金support from the National Natural Science Foundation of China(No.52271287)funding from the State Key Laboratory of Hydraulic Engineering Intelligent Construction and Operation,Tianjin University。
文摘During the hoisting process of the offshore substation,changes in the hoisting speed can affect the hoisting system.Therefore,this study set four different speed conditions for the lifting and lowering stages of the installation process,and studied the impact of different lifting and lowering speeds on the hoisting system under the same environmental conditions through numerical simulation.The results show that during the lifting operation,as the lifting speed increases,the swing motion of the substation and the installation vessel tends to decrease,and the faster the hoisting speed,the more obvious the swing suppression of the substation and the installation vessel,and the smaller the fluctuation in the tension amplitude of the slings and mooring lines.In contrast,during the lowering operation,as the lowering speed increases,the swing motion of the substation and the installation vessel tends to increase,and the faster the lowering speed,the more obvious the swing amplification effect of the substation and the installation vessel.Therefore,during hoisting operations,increasing the lifting speed and reducing the lowering speed can mitigate the motion performance of the hoisting coupling system,reduce the tension amplitude variation of the sling and mooring,and ensure the smooth progress of the hoisting operation.
基金supported by the National Natural Science Foundation of China(Nos.U22A20241 and 21876105)Shaanxi“Scientist&Engineer”Team(No.2023KXJ-131)Xianyang Key S&T Special Projects(No.L2023-ZDKJ-QCY-SXGG-GY-007).
文摘Electrocatalytic oxidation is a promising technology for wastewater treatment,but poor mass transfer and low current efficiency impaded its engineering applications.To address these issues,researchers have developed flow-through electrochemical reactors(FERs)primarily based on porous electrodes,where the pore structure significantly impacts the electrochemical reaction.Therefore,this study systematically investigated the impact of different pore sizes on the fluid dynamics,current potential distribution,mass transfer processes,and degradation performance of FERs.Computational Fluid Dynamics(CFD)results indicated that smaller pore sizes(10μm,30μm,and 60μm)significantly enhanced convective effects within the fluid,reduced short fluid paths and dead volume regions within the microchannels,and facilitated mass transfer processes.Additionally,smaller pore sizes were conducive to a uniform distribution of current density.Furthermore,Fe(CN)_(6)^(4−)oxidation experiments revealed that the current density at a pore size of 160μm was notably lower than that at 10μm,indicating slower mass transfer of Fe(CN)_(6)^(4−)within larger channels.Calculations based on experimental results demonstrated that the mass transfer rate at a pore size of 10μm was six times than that at 160μm,further confirming the enhancing effect of smaller pore sizes on the mass transfer process.Lastly,experiments on tetracycline degradation showed that at a residence time of 90 s,the removal efficiencies of tetracycline were 80%and 39.1%for porous electrodes with pore sizes of 10μm and 160μm,respectively,demonstrating the superior removal efficiency of smaller pore sizes for tetracycline degradation.
基金funded by the National Natural Science Foundation of China Youth Fund(Grant No.62304022)Science and Technology on Electromechanical Dynamic Control Laboratory(China,Grant No.6142601012304)the 2022e2024 China Association for Science and Technology Innovation Integration Association Youth Talent Support Project(Grant No.2022QNRC001).
文摘Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.
基金Funded by the National Natural Science Foundation of China Academy of Engineering Physics and Jointly Setup"NSAF"Joint Fund(No.U1430119)。
文摘The multi-scale modeling combined with the cohesive zone model(CZM)and the molecular dynamics(MD)method were preformed to simulate the crack propagation in NiTi shape memory alloys(SMAs).The metallographic microscope and image processing technology were employed to achieve a quantitative grain size distribution of NiTi alloys so as to provide experimental data for molecular dynamics modeling at the atomic scale.Considering the size effect of molecular dynamics model on material properties,a reasonable modeling size was provided by taking into account three characteristic dimensions from the perspective of macro,meso,and micro scales according to the Buckinghamπtheorem.Then,the corresponding MD simulation on deformation and fracture behavior was investigated to derive a parameterized traction-separation(T-S)law,and then it was embedded into cohesive elements of finite element software.Thus,the crack propagation behavior in NiTi alloys was reproduced by the finite element method(FEM).The experimental results show that the predicted initiation fracture toughness is in good agreement with experimental data.In addition,it is found that the dynamics initiation fracture toughness increases with decreasing grain size and increasing loading velocity.
文摘A model for dynamic frictionless contact between a viscoelastic body and foundation is considered.The viscoelastic constitutive law is assumed to be nonlinear and the contact is modelled with the normal compliance condition.We obtain the well-posedness using nonlinear semigroup theory arguments.Moreover,the exponential stability result of the solution is shown by using the energy method to produce a suitable Lyapunov function.
基金Project supported by the National Key Research and Development Program of China(Grant No.2024YFF0508503)。
文摘Strong long-wavelength laser pulses enable direct manipulation of atomic lattices for engineering novel quantum states in complex materials.Nonlinear coupling between two infrared-active phonon modes(TO_(1) and TO_(2)),induced by intense terahertz light fields,significantly enhances the amplitude of the TO_(1) mode and facilitates ultrafast control of transient structural distortions.This light-induced distortion reduces the lattice thermal conductivity from 8.1 W·m^(-1)·K^(-1)to 3.0 W·m^(-1)·K^(-1).The reduction originates from the nonlinear coupling,which enhances anharmonic interactions in the lattice potential energy and substantially shortens the phonon lifetime(τ).This work demonstrates a strategy applicable to other perovskite materials and provides a framework for investigating light-induced electrical,optical,and thermodynamic phase transitions.
基金supported in part by the National Science Fund for Distinguished Young Scholars of China(62225303)the National Natural Science Fundation of China(62303039,62433004)+2 种基金the China Postdoctoral Science Foundation(BX20230034,2023M730190)the Fundamental Research Funds for the Central Universities(buctrc202201,QNTD2023-01)the High Performance Computing Platform,College of Information Science and Technology,Beijing University of Chemical Technology
文摘Data-driven process monitoring is an effective approach to assure safe operation of modern manufacturing and energy systems,such as thermal power plants being studied in this work.Industrial processes are inherently dynamic and need to be monitored using dynamic algorithms.Mainstream dynamic algorithms rely on concatenating current measurement with past data.This work proposes a new,alternative dynamic process monitoring algorithm,using dot product feature analysis(DPFA).DPFA computes the dot product of consecutive samples,thus naturally capturing the process dynamics through temporal correlation.At the same time,DPFA's online computational complexity is lower than not just existing dynamic algorithms,but also classical static algorithms(e.g.,principal component analysis and slow feature analysis).The detectability of the new algorithm is analyzed for three types of faults typically seen in process systems:sensor bias,process fault and gain change fault.Through experiments with a numerical example and real data from a thermal power plant,the DPFA algorithm is shown to be superior to the state-of-the-art methods,in terms of better monitoring performance(fault detection rate and false alarm rate)and lower computational complexity.
基金Supported by National Key Research and Development Program(Grant No.2024YFB3312700)National Natural Science Foundation of China(Grant No.52405541)the Changzhou Municipal Sci&Tech Program(Grant No.CJ20241131)。
文摘Under the paradigm of Industry 5.0,intelligent manufacturing transcends mere efficiency enhancement by emphasizing human-machine collaboration,where human expertise plays a central role in assembly processes.Despite advancements in intelligent and digital technologies,assembly process design still heavily relies on manual knowledge reuse,and inefficiencies and inconsistent quality in process documentation are caused.To address the aforementioned issues,this paper proposes a knowledge push method of complex product assembly process design based on distillation model-based dynamically enhanced graph and Bayesian network.First,an initial knowledge graph is constructed using a BERT-BiLSTM-CRF model trained with integrated human expertise and a fine-tuned large language model.Then,a confidence-based dynamic weighted fusion strategy is employed to achieve dynamic incremental construction of the knowledge graph with low resource consumption.Subsequently,a Bayesian network model is constructed based on the relationships between assembly components,assembly features,and operations.Bayesian network reasoning is used to push assembly process knowledge under different design requirements.Finally,the feasibility of the Bayesian network construction method and the effectiveness of Bayesian network reasoning are verified through a specific example,significantly improving the utilization of assembly process knowledge and the efficiency of assembly process design.
基金the National Natural Science Foundation of China(10332050 and 10572144)Knowledge Innovation Program(KJCX-SW-L08)
文摘The calculation of settling speed of coarse particles is firstly addressed,with accelerated Stokesian dynamics without adjustable parameters,in which far field force acting on the particle instead of particle velocity is chosen as dependent variables to consider inter-particle hydrodynamic interactions.The sedimentation of a simple cubic array of spherical particles is simulated and compared to the results available to verify and validate the numerical code and computational scheme.The improved method keeps the same computational cost of the order O(NlogN)as usual accelerated Stokesian dynamics does.Then,more realistic random suspension sedimentation is investigated with the help of Mont Carlo method.The computational results agree well with experimental fitting.Finally,the sedimentation of finer cohesive particle,which is often observed in estuary environment,is presented as a further application in coastal engineering.
基金the Scientific Research Fund of Hunan Provincial Education Department(23A0423).
文摘Remote sensing imagery,due to its high altitude,presents inherent challenges characterized by multiple scales,limited target areas,and intricate backgrounds.These inherent traits often lead to increased miss and false detection rates when applying object recognition algorithms tailored for remote sensing imagery.Additionally,these complexities contribute to inaccuracies in target localization and hinder precise target categorization.This paper addresses these challenges by proposing a solution:The YOLO-MFD model(YOLO-MFD:Remote Sensing Image Object Detection withMulti-scale Fusion Dynamic Head).Before presenting our method,we delve into the prevalent issues faced in remote sensing imagery analysis.Specifically,we emphasize the struggles of existing object recognition algorithms in comprehensively capturing critical image features amidst varying scales and complex backgrounds.To resolve these issues,we introduce a novel approach.First,we propose the implementation of a lightweight multi-scale module called CEF.This module significantly improves the model’s ability to comprehensively capture important image features by merging multi-scale feature information.It effectively addresses the issues of missed detection and mistaken alarms that are common in remote sensing imagery.Second,an additional layer of small target detection heads is added,and a residual link is established with the higher-level feature extraction module in the backbone section.This allows the model to incorporate shallower information,significantly improving the accuracy of target localization in remotely sensed images.Finally,a dynamic head attentionmechanism is introduced.This allows themodel to exhibit greater flexibility and accuracy in recognizing shapes and targets of different sizes.Consequently,the precision of object detection is significantly improved.The trial results show that the YOLO-MFD model shows improvements of 6.3%,3.5%,and 2.5%over the original YOLOv8 model in Precision,map@0.5 and map@0.5:0.95,separately.These results illustrate the clear advantages of the method.
基金the National Natural Science Foundation of China(42374133)the Beijing Nova Program(2022056)for their funding of this research。
文摘Seismic data reconstruction can provide high-density sampling and regular input data for inversion and imaging,playing a crucial role in seismic data processing.In seismic data reconstruction,a common scenario involves a significant distance between the source and the first receiver,which makes it unattainable to acquire near-offset data.A new workflow for seismic data extrapolation is proposed to address this issue,which is based on a multi-scale dynamic time warping(MS-DTW)algorithm.MS-DTW can accurately calculate the time-shift between two time series and is a robust method for predicting time-offset(t-x)domain data.Using the time-shift calculated by the MS-DTW as the basic input,predict the two-way traveltime(TWT)of other traces based on the TWT of the reference trace.Perform autoregressive polynomial fitting on TWT and extrapolate TWT based on the fitted polynomial coefficients.Extract amplitude information from the TWT curve,fit the amplitude curve,and extrapolate the amplitude using polynomial coefficients.The proposed workflow does not necessitate data conversion to other domains and does not require prior knowledge of underground geological information.It applies to both isotropic and anisotropic media.The effectiveness of the workflow was verified through synthetic data and field data.The results show that compared with the method of predictive painting based on local slope,this approach can accurately predict missing near-offset seismic signals and demonstrates good robustness to noise.
基金Project (2007CB613803) supported by the National Basic Research Program of ChinaProject (2010GQC0170) supported by the Natural Science Foundation of Jiangxi Province,ChinaProject (GJJ11159) supported by the Educational Committee of Jiangxi Province,China
文摘The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that discontinuous dynamic recrystallization（DDRX） is the predominant recrystallization mechanism at temperature higher than 1050 °C and strain rate lower than 0.01 s-1.Meanwhile,continuous dynamic recrystallization is the main mechanism observed at temperature below 1050 °C and strain rate above 0.01 s-1,mixed with a few DDRX grains.In addition,decreasing strain rate and increasing deformation temperature are found to facilitate the progress of DRX and refinement of grains in the Ti alloy in β forging process.
文摘The absorbing process in isolating and coating process of α-olefin drag reducing polymer was studied by molecular dynamic simulation method, on basis of coating theory of α-olefin drag reducing polymer particles with polyurethane as coating material. The distributions of sodium laurate, sodium dodeeyl sulfate, and sodium dodeeyl benzene sulfonate on the surface of α-olefin drag reducing polymer particles were almost the same, but the bending degrees of them were obviously different. The bending degree of SLA molecules was greater than those of the other two surfactant molecules. Simulation results of absorbing and accumulating structure showed that, though hydrophobie properties of surfactant molecules were almost the same, water density around long chain sulfonate sodium was bigger than that around alkyl sulfate sodium. This property goes against useful absorbing and accumulating on the surface of α-olefin drag reducing polymer particles; simulation results of interactions of different surfactant and multiple hydroxyl compounds on surface of particles showed that, interactions of different surfaetant and one kind of multiple hydroxyl compound were similar to those of one kind of surfaetant and different multiple hydroxyl compounds. These two contrast types of interactions also exhibited the differences of absorbing distribution and closing degrees to surface of particles. The sequence of closing degrees was derived from simulation; control step of addition polymerization interaction in coating process was absorbing mass transfer process, so the more closed to surface of particle the multiple hydroxyl compounds were, the easier interactions With isoeyanate were. Simulation results represented the compatibility relationship between surfactant and multiple hydroxyl compounds. The isolating and coating processes of α-olefin drag reducing polymer were further understood on molecule and atom level through above simulation research, and based on the simulation, a referenced theoretical basis was provided for practical optimal selection and experimental preparation of α-olefin drag reducing polymer particles suspension isolation agent.
基金the National Natural Science Foundation of China(10377006).
文摘In the research of parachute, canopy inflation process modeling is one of the most complicated tasks. As canopy often experiences the largest deformations and loa-dings during a very short time, it is of great difficulty for theoretical analysis and experimental measurements. In this paper, aerodynamic equations and structural dynamics equations were developed for describing parachute opening process, and an iterative coupling solving strategy incorpo- rating the above equations was proposed for a small-scale, flexible and flat-circular parachute. Then, analyses were carried out for canopy geometry, time-dependent pressure difference between the inside and outside of the canopy, transient vortex around the canopy and the flow field in the radial plane as a sequence in opening process. The mechanism of the canopy shape development was explained from perspective of transient flow fields during the inflation process. Experiments of the parachute opening process were conducted in a wind tunnel, in which instantaneous shape of the canopy was measured by high velocity camera and the opening loading was measured by dynamometer balance. The theoretical predictions were found in good agreement with the experimental results, validating the proposed approach. This numerical method can improve the situation of strong dependence of parachute research on wind tunnel tests, and is of significance to the understanding of the mechanics of parachute inflation process.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.71871171,71871173,and 71832010)
文摘One of the assumptions of previous research in evolutionary game dynamics is that individuals use only one rule to update their strategy. In reality, an individual's strategy update rules may change with the environment, and it is possible for an individual to use two or more rules to update their strategy. We consider the case where an individual updates strategies based on the Moran and imitation processes, and establish mixed stochastic evolutionary game dynamics by combining both processes. Our aim is to study how individuals change strategies based on two update rules and how this affects evolutionary game dynamics. We obtain an analytic expression and properties of the fixation probability and fixation times(the unconditional fixation time or conditional average fixation time) associated with our proposed process. We find unexpected results. The fixation probability within the proposed model is independent of the probabilities that the individual adopts the imitation rule update strategy. This implies that the fixation probability within the proposed model is equal to that from the Moran and imitation processes. The one-third rule holds in the proposed mixed model. However, under weak selection, the fixation times are different from those of the Moran and imitation processes because it is connected with the probability that individuals adopt an imitation update rule. Numerical examples are presented to illustrate the relationships between fixation times and the probability that an individual adopts the imitation update rule, as well as between fixation times and selection intensity. From the simulated analysis, we find that the fixation time for a mixed process is greater than that of the Moran process, but is less than that of the imitation process. Moreover, the fixation times for a cooperator in the proposed process increase as the probability of adopting an imitation update increases; however, the relationship becomes more complex than a linear relationship.
基金supports from National High-Tech R&D Program of China (GrantNo. 2007AA03Z111)Natural Science Foundation of China (Grant No. 50604007)the Program for New Century Excellent Talents in University (Grant No.NCET-06-0285 and NCET-08-0097)
文摘In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firstly investigated. During casting AZ31 alloy by this process, non-uniform microstructure distributions and non- equilibrium solidification region near the roll surface were found in the roll-shoe gap. Microstructural evolution from dendrite to rosette and spherical grains was observed during the casting by CSEP. Casting temperature, roll-shoe gap width and cooling ability have great effect on casting process and metal flow, so these factors should be carefully controlled, a proper casting temperature of 710-750℃ is suggested. The white α phases were strongly stretched during the processing, and the remnant liquids are correspondingly distributes along the solid phase boundaries and also show stripped lines.
基金National Natural Science Foundation of China, No.40671186 No.40271012
文摘The western coast of Hainan Island exhibits a savanna landscape. Many types of sand dunes, including transverse dune ridges, longitudinal dune ridges, elliptical dunes, coppice dunes, and climbing dunes, are widely distributed in the coastal zone. In winter, high-frequency and high-energy NE winds （dominant winds） are prevalent, with a resultant drift direction （RDD） of S35.6°W. In spring, low-frequency and low-energy SW secondary winds prevail, with a RDD of N25.1°E. Wind tunnel simulations revealed that the airflow over the dune surface is the main factor controlling the erosion and deposition patterns of dune surfaces and the morphological development of dunes. In the region＇s bidirectional wind environment, with two seasonally distinct energy levels, the airflow over the surface of elliptical dunes, barchan dunes, and transverse dune ridges will exhibit a transverse pattern, whereas the airflow over longitudinal dunes ridges exhibits a lateral pattern and that over climbing dunes exhibits a climbing-circumfluent pattern. These patterns represent different dynamic processes. The coastal dunes on the western coast of Hainan Island are influenced by factors such as onshore winds, sand sources, coastal slopes, rivers, and forest shelter belts. The source of the sand that supplements these dunes particularly influences the development pattern： when there is more sand, the pattern shows positive equilibrium deposition between dune ridges and dunes; otherwise, it shows negative equilibrium deposition. The presence or absence of forest shelter belts also influences deposition and dune development patterns and transformation of dune forms. Coastal dunes and inland desert dunes experience similar dynamic processes, but the former have more diversified shapes and more complex formation mechanisms.
基金the National Natural science Foundation of China (No. 71701008) for supporting this research
文摘For critical engineering systems such as aircraft and aerospace vehicles, accurate Remaining Useful Life(RUL) prediction not only means cost saving, but more importantly, is of great significance in ensuring system reliability and preventing disaster. RUL is affected not only by a system's intrinsic deterioration, but also by the operational conditions under which the system is operating. This paper proposes an RUL prediction approach to estimate the mean RUL of a continuously degrading system under dynamic operational conditions and subjected to condition monitoring at short equi-distant intervals. The dynamic nature of the operational conditions is described by a discrete-time Markov chain, and their influences on the degradation signal are quantified by degradation rates and signal jumps in the degradation model. The uniqueness of our proposed approach is formulating the RUL prediction problem in a semi-Markov decision process framework, by which the system mean RUL can be obtained through the solution to a limited number of equations. To extend the use of our proposed approach in real applications, different failure standards according to different operational conditions are also considered. The application and effectiveness of this approach are illustrated by a turbofan engine dataset and a comparison with existing results for the same dataset.
文摘Abstract The Nansha ultra-crust layer-block is confined by ultra-crustal boundary faults of distinctive features, bordering the Kangtai-Shuangzi-Xiongnan extensional faulted zone on the north, the Baxian-Baram-Yoca-Cuyo nappe faulted zone on the south, the Wan'an-Natuna strike-slip tensional faulted zone on the west and the Mondoro-Panay strike-slip compressive faulted zone on the east. These faults take the top of the Nansha asthenosphere as their common detachmental surface. The Cenozoic dynamic process of the ultra-crust layer-block can be divided into four stages: K2-E21, during which the northern boundary faults extended, this ultra-crust layer-block was separated from the South China-Indosinian continental margin, the Palaeo-South China Sea subducted southwards and the Sibu accretion wedge was formed; E22-E31, during which the Southwest sub-sea basin extended and orogeny was active due to the collision of the Sibu accretion wedge; E32-N11, during which the central sub-sea basin extended, the Miri accretion wedge was formed and “A-type” subduction of the southern margin of the north Balawan occurred; N12-the present, during which large-scale thrusting and napping of the boundary faults in the south and mountain-building have taken place and the South China Sea stopped its extension.
