Combining the vector level set model,the shape sensitivity analysis theory with the gradient projection technique,a level set method for topology optimization with multi-constraints and multi-materials is presented in...Combining the vector level set model,the shape sensitivity analysis theory with the gradient projection technique,a level set method for topology optimization with multi-constraints and multi-materials is presented in this paper.The method implicitly describes structural material in- terfaces by the vector level set and achieves the optimal shape and topology through the continuous evolution of the material interfaces in the structure.In order to increase computational efficiency for a fast convergence,an appropriate nonlinear speed mapping is established in the tangential space of the active constraints.Meanwhile,in order to overcome the numerical instability of general topology opti- mization problems,the regularization with the mean curvature flow is utilized to maintain the interface smoothness during the optimization process.The numerical examples demonstrate that the approach possesses a good flexibility in handling topological changes and gives an interface representation in a high fidelity,compared with other methods based on explicit boundary variations in the literature.展开更多
The least-square gridless method was extended to simulate the compressible multi-material flows. The algorithm was accomplished to solve the Arbitrary Lagrange-Euler( ALE) formulation. The local least-square curve fit...The least-square gridless method was extended to simulate the compressible multi-material flows. The algorithm was accomplished to solve the Arbitrary Lagrange-Euler( ALE) formulation. The local least-square curve fits was adopted to approximate the spatial derivatives of a point on the base of the points in its circular support domain,and the basis function was linear. The HLLC( Harten-Lax-van Leer-Contact) scheme was used to calculate the inviscid flux. On the material interfaces,the gridless points were endued with a dual definition corresponding to different materials. The moving velocity of the interface points was updated by solving the Riemann problem. The interface boundary condition was built by using the Ghost Fluid Method( GFM).Computations were performed for several one and two dimensional typical examples. The numerical results show that the interface and the shock wave are well captured,which proves the effectiveness of gridless method in dealing with multi-material flow problems.展开更多
A new flux-based hybrid subcell-remapping algorithm for staggered multimaterial arbitrary Lagrangian-Eulerian (MMALE) methods is presented. This new method is an effective generalization of the original subcell-remapp...A new flux-based hybrid subcell-remapping algorithm for staggered multimaterial arbitrary Lagrangian-Eulerian (MMALE) methods is presented. This new method is an effective generalization of the original subcell-remapping method to the multi-material regime (LOUBERE, R. and SHASHKOV,M. A subcell remapping method on staggered polygonal grids for arbitrary-Lagrangian-Eulerian methods. Journal of Computational Physics, 209, 105–138 (2005)). A complete remapping procedure of all fluid quantities is described detailedly in this paper. In the pure material regions, remapping of mass and internal energy is performed by using the original subcell-remapping method. In the regions near the material interfaces, remapping of mass and internal energy is performed with the intersection-based fluxes where intersections are performed between the swept regions and pure material polygons in the Lagrangian mesh, and an approximate approach is then introduced for constructing the subcell mass fluxes. In remapping of the subcell momentum, the mass fluxes are used to construct the momentum fluxes by multiplying a reconstructed velocity in the swept region. The nodal velocity is then conservatively recovered. Some numerical examples simulated in the full MMALE regime and several purely cyclic remapping examples are presented to prove the properties of the remapping method.展开更多
LS-DYNA program and the principle of ALE method were introduced, and the target features of the reinforced concrete penetration were analyzed by using the D material model and the ALE method. A numerical simulation ha...LS-DYNA program and the principle of ALE method were introduced, and the target features of the reinforced concrete penetration were analyzed by using the D material model and the ALE method. A numerical simulation has been done to show the penetration visually and veritably. The simulation results are analyzed carefully and explicitly prove their significance to the research of reinforced concrete penetration.展开更多
In the paper, the numerical simulation of interface problems for multiple material fluids is studied. The level set function is designed to capture the location of the material interface. For multi-dimensional and mul...In the paper, the numerical simulation of interface problems for multiple material fluids is studied. The level set function is designed to capture the location of the material interface. For multi-dimensional and multi-material fluids, the modified ghost fluid method needs a Riemann solution to renew the variable states near the interface. Here we present a new convenient and effective algorithm for solving the Riemann problem in the normal direction. The extrapolated variables are populated by Taylor series expansions in the direction. The anti-diffusive high order WENO difference scheme with the limiter is adopted for the numerical simulation. Finally we implement a series of numerical experiments of multi-material flows. The obtained results are satisfying, compared to those by other methods.展开更多
This paper presents a robust topology optimization design approach for multi-material functional graded structures under periodic constraint with load uncertainties.To characterize the random-field uncertainties with ...This paper presents a robust topology optimization design approach for multi-material functional graded structures under periodic constraint with load uncertainties.To characterize the random-field uncertainties with a reduced set of random variables,the Karhunen-Lo`eve(K-L)expansion is adopted.The sparse grid numerical integration method is employed to transform the robust topology optimization into a weighted summation of series of deterministic topology optimization.Under dividing the design domain,the volume fraction of each preset gradient layer is extracted.Based on the ordered solid isotropic microstructure with penalization(Ordered-SIMP),a functionally graded multi-material interpolation model is formulated by individually optimizing each preset gradient layer.The periodic constraint setting of the gradient layer is achieved by redistributing the average element compliance in sub-regions.Then,the method of moving asymptotes(MMA)is introduced to iteratively update the design variables.Several numerical examples are presented to verify the validity and applicability of the proposed method.The results demonstrate that the periodic functionally graded multi-material topology can be obtained under different numbers of sub-regions,and robust design structures are more stable than that indicated by the deterministic results.展开更多
A computational procedure is developed to solve the problems of coupled motion of a structure and a viscous incompressible fluid. In order to incorporate the effect of the moving surface of the structure as well as th...A computational procedure is developed to solve the problems of coupled motion of a structure and a viscous incompressible fluid. In order to incorporate the effect of the moving surface of the structure as well as the free surface motion, the arbitrary Lagrangian-Eulerian formulation is employed as the basis of the finite element spatial discretization. For numerical integration in time, the fraction,step method is used. This method is useful because one can use the same linear interpolation function for both velocity and pressure. The method is applied to the nonlinear interaction of a structure and a tuned liquid damper. All computations are performed with a personal computer.展开更多
Using arbitrary Lagrangian-Eulerian(ALE)finite element method,this paper made a comparative study of the opening and closing behaviour of a downstream directional valve(DDM)and a St.Jude medical valve(SJM)through a tw...Using arbitrary Lagrangian-Eulerian(ALE)finite element method,this paper made a comparative study of the opening and closing behaviour of a downstream directional valve(DDM)and a St.Jude medical valve(SJM)through a two dimensional model of mechanical valve-blood interaction in which the valve is considered as a rigid body rotating around a fixed point,and the blood is simplified as viscous incompressible fluid It's concluded that:(1)Compared with SJM valve, DDM valve opens faster and closes the more gently.(2)The peak badk-flow-flow of DDM is smaller than that of SJM.The present investigation shows that being a better analogue of natural valve,DDM has a brighter potential on its durability than SJM.展开更多
The application of multi-material topology optimization affords greater design flexibility compared to traditional single-material methods.However,density-based topology optimization methods encounter three unique cha...The application of multi-material topology optimization affords greater design flexibility compared to traditional single-material methods.However,density-based topology optimization methods encounter three unique challenges when inertial loads become dominant:non-monotonous behavior of the objective function,possible unconstrained characterization of the optimal solution,and parasitic effects.Herein,an improved Guide-Weight approach is introduced,which effectively addresses the structural topology optimization problem when subjected to inertial loads.Smooth and fast convergence of the compliance is achieved by the approach,while also maintaining the effectiveness of the volume constraints.The rational approximation of material properties model and smooth design are utilized to guarantee clear boundaries of the final structure,facilitating its seamless integration into manufacturing processes.The framework provided by the alternating active-phase algorithm is employed to decompose the multi-material topological problem under inertial loading into a set of sub-problems.The optimization of multi-material under inertial loads is accomplished through the effective resolution of these sub-problems using the improved Guide-Weight method.The effectiveness of the proposed approach is demonstrated through numerical examples involving two-phase and multi-phase materials.展开更多
Base d on fluid velocity potential, an ALE finite element formulation for the analysi s of nonlinear sloshing problems has been developed. The ALE kinemat ical description is introduced to move the computational mesh...Base d on fluid velocity potential, an ALE finite element formulation for the analysi s of nonlinear sloshing problems has been developed. The ALE kinemat ical description is introduced to move the computational mesh independently of f luid motion, and the container fixed noninertial coordinate system is employed to establish the governing equations so that the mesh is needed to be updated in this coordinate system only. This leads to a very simple mesh moving algorithm which makes it easy to trace the motion of the moving boundaries and the free su rface without producing undesirable distortion of the computational mesh. The fi nite element method and finite difference method are used spacewise and timewise , respectively. A numerical example involving either forced horizontal oscillati on or forced pitching oscillation of the fluid filled container is presented to illustrate the effectiveness and the robustness of the method. In additi on, this work can be extended for the fluid structure interaction problems.展开更多
Solidifi cation shrinkage has been recognized as an important factor for macrosegregation formation. An arbitrary Lagrangian–Eulerian(ALE) model is constructed to predict the macrosegregation caused by thermal–solut...Solidifi cation shrinkage has been recognized as an important factor for macrosegregation formation. An arbitrary Lagrangian–Eulerian(ALE) model is constructed to predict the macrosegregation caused by thermal–solutal convection and solidi-fi cation shrinkage. A novel mesh update algorithm is developed to account for the domain change induced by solidifi cation shrinkage. The velocity–pressure coupling between the non-homogenous mass conservation equation and momentum equation is addressed by a modifi ed pressure correction method. The governing equations are solved by the streamline-upwind/Petrov–Galerkin-stabilized fi nite element algorithm. The application of the model to the Pb-19.2 wt%Sn alloy solidifi cation problem is considered. The inverse segregation is successfully predicted, and reasonable agreement with the literature results is obtained. Thus, the ALE model is established to be a highly effective tool for predicting the macrosegregation caused by solidifi cation shrinkage and thermal–solutal convection. Finally, the effect of solidifi cation shrinkage is analyzed. The results demonstrate that solidifi cation shrinkage delays the advance of the solidifi cation front and intensifi es the segregation.展开更多
Employing arbitrary Lagrangian-Eulerian (ALE) finite element method, this poper studies the opening and closing process of a St. Jude medical valve through a two-dimensional model of the mechanical valve-blood interac...Employing arbitrary Lagrangian-Eulerian (ALE) finite element method, this poper studies the opening and closing process of a St. Jude medical valve through a two-dimensional model of the mechanical valve-blood interaction in which the valve is regarded as a rigid body rotating around a fixed point, and foe blood is simplified as viscous incompressible Newtonian fluid. The numerical analysis of the opening and closing behaviour of as St. Jude valve suggested that: 1. The whole opening and closing process of an artificial mechanical valve is consisted of four phases: (1) Opening phase; (2) Opening maintenance phase; (3) Closing phase; (4) Closing maintenance phase. 2. The St. Jude medical valve closes with prominent regurgitat which results in water-hammer effect. 3. During the opening and closing process of the St. Jude valve,high shear stresses occur in the middle region of the two leaflets and on the valve ring. The present model has made a breakthrough on the coupling computational analysis considering the interactive movement of the valve and blood.展开更多
Sand mold 3D printing technology based on the principle of droplet ejection has undergone rapid development in recent years and has elicited increasing attention from engineers and technicians.However,current sand mol...Sand mold 3D printing technology based on the principle of droplet ejection has undergone rapid development in recent years and has elicited increasing attention from engineers and technicians.However,current sand mold 3D printing technology exhibits several problems,such as single-material printing molds,low manufacturing efficiency,and necessary post-process drying and heating for the manufacture of sand molds.This study proposes a novel high-efficiency print forming method and device for multi-material casting molds.The proposed method is specifically related to the integrated forming of two-way coating and printing and the shortflow manufacture of roller compaction and layered heating.These processes can realize the high-efficiency print forming of high-performance sand molds.Experimental results demonstrate that the efficiency of sand mold fabrication can be increased by 200%using the proposed two-way coating and printing method.The integrated forming method for layered heating and roller compaction presented in this study effectively shortens the manufacturing process for 3D-printed sand molds,increases sand mold strength by 63.8%,and reduces resin usage by approximately 30%.The manufacture of multi-material casting molds is demonstrated on typical wheeled cast-iron parts.This research provides theoretical guidance for the engineering application of sand mold 3D printing.展开更多
Combining the strengths of Lagrangian and Eulerian descriptions,the coupled Lagrangian–Eulerian methods play an increasingly important role in various subjects.This work reviews their development and application in o...Combining the strengths of Lagrangian and Eulerian descriptions,the coupled Lagrangian–Eulerian methods play an increasingly important role in various subjects.This work reviews their development and application in ocean engineering.Initially,we briefly outline the advantages and disadvantages of the Lagrangian and Eulerian descriptions and the main characteristics of the coupled Lagrangian–Eulerian approach.Then,following the developmental trajectory of these methods,the fundamental formulations and the frameworks of various approaches,including the arbitrary Lagrangian–Eulerian finite element method,the particle-in-cell method,the material point method,and the recently developed Lagrangian–Eulerian stabilized collocation method,are detailedly reviewed.In addition,the article reviews the research progress of these methods with applications in ocean hydrodynamics,focusing on free surface flows,numerical wave generation,wave overturning and breaking,interactions between waves and coastal structures,fluid–rigid body interactions,fluid–elastic body interactions,multiphase flow problems and visualization of ocean flows,etc.Furthermore,the latest research advancements in the numerical stability,accuracy,efficiency,and consistency of the coupled Lagrangian–Eulerian particle methods are reviewed;these advancements enable efficient and highly accurate simulation of complicated multiphysics problems in ocean and coastal engineering.By building on these works,the current challenges and future directions of the hybrid Lagrangian–Eulerian particle methods are summarized.展开更多
The ghost fluid method(GFM)provides a simple way to simulate the interaction of immiscible materials.Especially,the modified GFM(MGFM)and its variants,based on the solutions of multi-material Riemann problems,are capa...The ghost fluid method(GFM)provides a simple way to simulate the interaction of immiscible materials.Especially,the modified GFM(MGFM)and its variants,based on the solutions of multi-material Riemann problems,are capable of faithfully taking into account the effects of nonlinear wave interaction and material property near the interface.Reasonable treatments for ghost fluid states or interface conditions have been shown to be crucial when applied to various interfacial phenomena involving large discontinuity and strong nonlinearity.These methods,therefore,have great potential in engineering applications.In this paper,we review the development of such methods.The methodologies of representative GFM-based algorithms for definition of interface conditions are illustrated and compared to each other.The research progresses in design principle and accuracy analysis are briefly described.Some steps and techniques for multi-dimensional extension are also summarized.In addition,we present some progresses in more challenging scientific problems,including a variety of fluid/solid-fluid/solid interactions with complex physical properties.Of course the challenges faced by researchers in this field are also discussed.展开更多
The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field ...The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field distributions of strain rate,stress,temperature and velocity of metal flow were obtained.The results are basically consistent with the experiment,which indicates that this method may successfully predict the defects in the actual extrusion process.展开更多
Ditching is considered as one of the important aspects of safety performances of airplanes. It is related primarily with the fluid-solid interaction, whose studies mainly depend on experiments at the present time. Num...Ditching is considered as one of the important aspects of safety performances of airplanes. It is related primarily with the fluid-solid interaction, whose studies mainly depend on experiments at the present time. Numerical and analytical methods for fluid-solid interaction by using 3-D full scale airplane＇s model will reduce the dependence on the expensive model tests. Numerical studies can be used to estimate the safety of ditching and provide a reference for the crashworthiness design. This article proposes a 3-D dynamical structural model after the real shape of an airplane and an Arbitrary Lagrange-Euler （ALE） fluid-field model, to simulate the fluid-solid interactions caused by low speed ditching. The simulation is based on interaction computational methods, within LS-DYNA nonlinear finite-element code. The results of pressure distributions and accelerating time histories of the airplane＇s subfloor are discussed in the context of the safety of ditching, and the simulation results and the analytical methods are verified.展开更多
A numerical study was conducted for the vortex-induced vibrations of anelastic circular cylinder at low Reynolds numbers. An Arbitrary Lagrangian-Eulerian (ALE) method wasemployed to deal with the fluid-structure inte...A numerical study was conducted for the vortex-induced vibrations of anelastic circular cylinder at low Reynolds numbers. An Arbitrary Lagrangian-Eulerian (ALE) method wasemployed to deal with the fluid-structure interaction with an H-O type of non-staggered gridsincorporating the domain decomposition method (DDM), which could save the computational CPU time dueto re-meshing. The computational domain was divided into nine sub-domains including one ALEsub-domain and eight Eulerian sub-domains. The convection term and dissipation term in the N-Sequations were discretized using the third-order upwind compact scheme and the fourth-order centralcompact scheme, respectively. The motion of the cylinder was modeled by a spring-damper-mass systemand solved using the Runge-Kutta method. By simulating the non-linear fluid-structure interaction,the ''lock-in'', ''beating'' and ''phase switch'' phenomena were successfully captured, and the resultsagree with experimental data Furthermore, the vortex structure, the unsteady lift and drag on thecylinder, and the cylinder displacement at various natural frequency of the cylinder for Re = 200were discussed in detail, by which a jump transition of the wake structure was captured.展开更多
Non-equal channel lateral extrusion（NECLE） is a new process that can be used to attain higher grain refinement in comparison with equal channel lateral extrusion（ECLE）. The die design for this process was numerica...Non-equal channel lateral extrusion（NECLE） is a new process that can be used to attain higher grain refinement in comparison with equal channel lateral extrusion（ECLE）. The die design for this process was numerically and experimentally studied. After finding a good correlation between the numerical and experimental results, more comprehensive FE analyses were carried out. Different die geometrical parameters were considered and their effects on the induced plastic strain, stress distribution, velocity field and forming load of the process were investigated. It was found that by this process with a suitable set of die geometrical parameters, higher induced effective strain and more homogeneous strain distribution could be achieved in comparison with ECLE operation.展开更多
Based on the theory of optimization,we use edges and angles of cells to represent the geometric quality of computational grids,employ the local gradients of the flow variables to describe the variation of flow field,a...Based on the theory of optimization,we use edges and angles of cells to represent the geometric quality of computational grids,employ the local gradients of the flow variables to describe the variation of flow field,and construct a multi-objective programming model.The solution of this optimization problem gives appropriate balance between the geometric quality and adaptation of grids.By solving the optimization problem,we propose a new grid rezoning method,which not only keeps good geometric quality of grids,but also can track rapid changes in the flow field.In particular,it performs well for some complex concave domains with corners.We also incorporate the rezoningmethod into anArbitrary Lagrangian-Eulerian(ALE)method which is widely used in the simulation of high-speed multi-material flows.The proposed rezoning and ALE methods of this paper are tested by a number of numerical examples with complex concave domains and compared with some other rezoning methods.The numerical results validate the robustness of the proposed methods.展开更多
基金The project supported by the National Natural Science Foundation of China (59805001,10332010) and Key Science and Technology Research Project of Ministry of Education of China (No.104060)
文摘Combining the vector level set model,the shape sensitivity analysis theory with the gradient projection technique,a level set method for topology optimization with multi-constraints and multi-materials is presented in this paper.The method implicitly describes structural material in- terfaces by the vector level set and achieves the optimal shape and topology through the continuous evolution of the material interfaces in the structure.In order to increase computational efficiency for a fast convergence,an appropriate nonlinear speed mapping is established in the tangential space of the active constraints.Meanwhile,in order to overcome the numerical instability of general topology opti- mization problems,the regularization with the mean curvature flow is utilized to maintain the interface smoothness during the optimization process.The numerical examples demonstrate that the approach possesses a good flexibility in handling topological changes and gives an interface representation in a high fidelity,compared with other methods based on explicit boundary variations in the literature.
文摘The least-square gridless method was extended to simulate the compressible multi-material flows. The algorithm was accomplished to solve the Arbitrary Lagrange-Euler( ALE) formulation. The local least-square curve fits was adopted to approximate the spatial derivatives of a point on the base of the points in its circular support domain,and the basis function was linear. The HLLC( Harten-Lax-van Leer-Contact) scheme was used to calculate the inviscid flux. On the material interfaces,the gridless points were endued with a dual definition corresponding to different materials. The moving velocity of the interface points was updated by solving the Riemann problem. The interface boundary condition was built by using the Ghost Fluid Method( GFM).Computations were performed for several one and two dimensional typical examples. The numerical results show that the interface and the shock wave are well captured,which proves the effectiveness of gridless method in dealing with multi-material flow problems.
基金Project supported by the China Postdoctoral Science Foundation(No.2017M610823)
文摘A new flux-based hybrid subcell-remapping algorithm for staggered multimaterial arbitrary Lagrangian-Eulerian (MMALE) methods is presented. This new method is an effective generalization of the original subcell-remapping method to the multi-material regime (LOUBERE, R. and SHASHKOV,M. A subcell remapping method on staggered polygonal grids for arbitrary-Lagrangian-Eulerian methods. Journal of Computational Physics, 209, 105–138 (2005)). A complete remapping procedure of all fluid quantities is described detailedly in this paper. In the pure material regions, remapping of mass and internal energy is performed by using the original subcell-remapping method. In the regions near the material interfaces, remapping of mass and internal energy is performed with the intersection-based fluxes where intersections are performed between the swept regions and pure material polygons in the Lagrangian mesh, and an approximate approach is then introduced for constructing the subcell mass fluxes. In remapping of the subcell momentum, the mass fluxes are used to construct the momentum fluxes by multiplying a reconstructed velocity in the swept region. The nodal velocity is then conservatively recovered. Some numerical examples simulated in the full MMALE regime and several purely cyclic remapping examples are presented to prove the properties of the remapping method.
文摘LS-DYNA program and the principle of ALE method were introduced, and the target features of the reinforced concrete penetration were analyzed by using the D material model and the ALE method. A numerical simulation has been done to show the penetration visually and veritably. The simulation results are analyzed carefully and explicitly prove their significance to the research of reinforced concrete penetration.
文摘In the paper, the numerical simulation of interface problems for multiple material fluids is studied. The level set function is designed to capture the location of the material interface. For multi-dimensional and multi-material fluids, the modified ghost fluid method needs a Riemann solution to renew the variable states near the interface. Here we present a new convenient and effective algorithm for solving the Riemann problem in the normal direction. The extrapolated variables are populated by Taylor series expansions in the direction. The anti-diffusive high order WENO difference scheme with the limiter is adopted for the numerical simulation. Finally we implement a series of numerical experiments of multi-material flows. The obtained results are satisfying, compared to those by other methods.
基金This work is supported by the Natural Science Foundation of China(Grant 51705268)China Postdoctoral Science Foundation Funded Project(Grant 2017M612191).
文摘This paper presents a robust topology optimization design approach for multi-material functional graded structures under periodic constraint with load uncertainties.To characterize the random-field uncertainties with a reduced set of random variables,the Karhunen-Lo`eve(K-L)expansion is adopted.The sparse grid numerical integration method is employed to transform the robust topology optimization into a weighted summation of series of deterministic topology optimization.Under dividing the design domain,the volume fraction of each preset gradient layer is extracted.Based on the ordered solid isotropic microstructure with penalization(Ordered-SIMP),a functionally graded multi-material interpolation model is formulated by individually optimizing each preset gradient layer.The periodic constraint setting of the gradient layer is achieved by redistributing the average element compliance in sub-regions.Then,the method of moving asymptotes(MMA)is introduced to iteratively update the design variables.Several numerical examples are presented to verify the validity and applicability of the proposed method.The results demonstrate that the periodic functionally graded multi-material topology can be obtained under different numbers of sub-regions,and robust design structures are more stable than that indicated by the deterministic results.
文摘A computational procedure is developed to solve the problems of coupled motion of a structure and a viscous incompressible fluid. In order to incorporate the effect of the moving surface of the structure as well as the free surface motion, the arbitrary Lagrangian-Eulerian formulation is employed as the basis of the finite element spatial discretization. For numerical integration in time, the fraction,step method is used. This method is useful because one can use the same linear interpolation function for both velocity and pressure. The method is applied to the nonlinear interaction of a structure and a tuned liquid damper. All computations are performed with a personal computer.
文摘Using arbitrary Lagrangian-Eulerian(ALE)finite element method,this paper made a comparative study of the opening and closing behaviour of a downstream directional valve(DDM)and a St.Jude medical valve(SJM)through a two dimensional model of mechanical valve-blood interaction in which the valve is considered as a rigid body rotating around a fixed point,and the blood is simplified as viscous incompressible fluid It's concluded that:(1)Compared with SJM valve, DDM valve opens faster and closes the more gently.(2)The peak badk-flow-flow of DDM is smaller than that of SJM.The present investigation shows that being a better analogue of natural valve,DDM has a brighter potential on its durability than SJM.
基金supported by the National Natural Science Foundation of China(Grant No.52172356)the Hunan Provincial Natural Science Foundation of China(Grant No.2022JJ10012).
文摘The application of multi-material topology optimization affords greater design flexibility compared to traditional single-material methods.However,density-based topology optimization methods encounter three unique challenges when inertial loads become dominant:non-monotonous behavior of the objective function,possible unconstrained characterization of the optimal solution,and parasitic effects.Herein,an improved Guide-Weight approach is introduced,which effectively addresses the structural topology optimization problem when subjected to inertial loads.Smooth and fast convergence of the compliance is achieved by the approach,while also maintaining the effectiveness of the volume constraints.The rational approximation of material properties model and smooth design are utilized to guarantee clear boundaries of the final structure,facilitating its seamless integration into manufacturing processes.The framework provided by the alternating active-phase algorithm is employed to decompose the multi-material topological problem under inertial loading into a set of sub-problems.The optimization of multi-material under inertial loads is accomplished through the effective resolution of these sub-problems using the improved Guide-Weight method.The effectiveness of the proposed approach is demonstrated through numerical examples involving two-phase and multi-phase materials.
文摘Base d on fluid velocity potential, an ALE finite element formulation for the analysi s of nonlinear sloshing problems has been developed. The ALE kinemat ical description is introduced to move the computational mesh independently of f luid motion, and the container fixed noninertial coordinate system is employed to establish the governing equations so that the mesh is needed to be updated in this coordinate system only. This leads to a very simple mesh moving algorithm which makes it easy to trace the motion of the moving boundaries and the free su rface without producing undesirable distortion of the computational mesh. The fi nite element method and finite difference method are used spacewise and timewise , respectively. A numerical example involving either forced horizontal oscillati on or forced pitching oscillation of the fluid filled container is presented to illustrate the effectiveness and the robustness of the method. In additi on, this work can be extended for the fluid structure interaction problems.
基金supported by the National Natural Science Foundation of China-Liaoning Joint Fund (U1508215)
文摘Solidifi cation shrinkage has been recognized as an important factor for macrosegregation formation. An arbitrary Lagrangian–Eulerian(ALE) model is constructed to predict the macrosegregation caused by thermal–solutal convection and solidi-fi cation shrinkage. A novel mesh update algorithm is developed to account for the domain change induced by solidifi cation shrinkage. The velocity–pressure coupling between the non-homogenous mass conservation equation and momentum equation is addressed by a modifi ed pressure correction method. The governing equations are solved by the streamline-upwind/Petrov–Galerkin-stabilized fi nite element algorithm. The application of the model to the Pb-19.2 wt%Sn alloy solidifi cation problem is considered. The inverse segregation is successfully predicted, and reasonable agreement with the literature results is obtained. Thus, the ALE model is established to be a highly effective tool for predicting the macrosegregation caused by solidifi cation shrinkage and thermal–solutal convection. Finally, the effect of solidifi cation shrinkage is analyzed. The results demonstrate that solidifi cation shrinkage delays the advance of the solidifi cation front and intensifi es the segregation.
文摘Employing arbitrary Lagrangian-Eulerian (ALE) finite element method, this poper studies the opening and closing process of a St. Jude medical valve through a two-dimensional model of the mechanical valve-blood interaction in which the valve is regarded as a rigid body rotating around a fixed point, and foe blood is simplified as viscous incompressible Newtonian fluid. The numerical analysis of the opening and closing behaviour of as St. Jude valve suggested that: 1. The whole opening and closing process of an artificial mechanical valve is consisted of four phases: (1) Opening phase; (2) Opening maintenance phase; (3) Closing phase; (4) Closing maintenance phase. 2. The St. Jude medical valve closes with prominent regurgitat which results in water-hammer effect. 3. During the opening and closing process of the St. Jude valve,high shear stresses occur in the middle region of the two leaflets and on the valve ring. The present model has made a breakthrough on the coupling computational analysis considering the interactive movement of the valve and blood.
基金This research was supported by the National Excellent Young Scientists Fund(Grant No.51525503).
文摘Sand mold 3D printing technology based on the principle of droplet ejection has undergone rapid development in recent years and has elicited increasing attention from engineers and technicians.However,current sand mold 3D printing technology exhibits several problems,such as single-material printing molds,low manufacturing efficiency,and necessary post-process drying and heating for the manufacture of sand molds.This study proposes a novel high-efficiency print forming method and device for multi-material casting molds.The proposed method is specifically related to the integrated forming of two-way coating and printing and the shortflow manufacture of roller compaction and layered heating.These processes can realize the high-efficiency print forming of high-performance sand molds.Experimental results demonstrate that the efficiency of sand mold fabrication can be increased by 200%using the proposed two-way coating and printing method.The integrated forming method for layered heating and roller compaction presented in this study effectively shortens the manufacturing process for 3D-printed sand molds,increases sand mold strength by 63.8%,and reduces resin usage by approximately 30%.The manufacture of multi-material casting molds is demonstrated on typical wheeled cast-iron parts.This research provides theoretical guidance for the engineering application of sand mold 3D printing.
基金the support received from the Laoshan Laboratory(No.LSKJ202202000)the National Natural Science Foundation of China(Grant Nos.12032002,U22A20256,and 12302253)the Natural Science Foundation of Beijing(No.L212023)for partially funding this work.
文摘Combining the strengths of Lagrangian and Eulerian descriptions,the coupled Lagrangian–Eulerian methods play an increasingly important role in various subjects.This work reviews their development and application in ocean engineering.Initially,we briefly outline the advantages and disadvantages of the Lagrangian and Eulerian descriptions and the main characteristics of the coupled Lagrangian–Eulerian approach.Then,following the developmental trajectory of these methods,the fundamental formulations and the frameworks of various approaches,including the arbitrary Lagrangian–Eulerian finite element method,the particle-in-cell method,the material point method,and the recently developed Lagrangian–Eulerian stabilized collocation method,are detailedly reviewed.In addition,the article reviews the research progress of these methods with applications in ocean hydrodynamics,focusing on free surface flows,numerical wave generation,wave overturning and breaking,interactions between waves and coastal structures,fluid–rigid body interactions,fluid–elastic body interactions,multiphase flow problems and visualization of ocean flows,etc.Furthermore,the latest research advancements in the numerical stability,accuracy,efficiency,and consistency of the coupled Lagrangian–Eulerian particle methods are reviewed;these advancements enable efficient and highly accurate simulation of complicated multiphysics problems in ocean and coastal engineering.By building on these works,the current challenges and future directions of the hybrid Lagrangian–Eulerian particle methods are summarized.
基金supported under the National Natural Science Foundation of China(Nos.11872351 and U1730118)Science Challenge Project(No.JCKY2016212A502).
文摘The ghost fluid method(GFM)provides a simple way to simulate the interaction of immiscible materials.Especially,the modified GFM(MGFM)and its variants,based on the solutions of multi-material Riemann problems,are capable of faithfully taking into account the effects of nonlinear wave interaction and material property near the interface.Reasonable treatments for ghost fluid states or interface conditions have been shown to be crucial when applied to various interfacial phenomena involving large discontinuity and strong nonlinearity.These methods,therefore,have great potential in engineering applications.In this paper,we review the development of such methods.The methodologies of representative GFM-based algorithms for definition of interface conditions are illustrated and compared to each other.The research progresses in design principle and accuracy analysis are briefly described.Some steps and techniques for multi-dimensional extension are also summarized.In addition,we present some progresses in more challenging scientific problems,including a variety of fluid/solid-fluid/solid interactions with complex physical properties.Of course the challenges faced by researchers in this field are also discussed.
基金Project (2009A080205003) supported by the Major Science and Technology Project of Guangdong Province,ChinaProject (30815009) supported by the Foundation of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body,China
文摘The arbitrary Lagrangian-Eulerian（ALE） adaptive remeshing technology and the HyperXtrude software of transient finite element simulations were used on analogue simulation of aluminium extrusion processing.The field distributions of strain rate,stress,temperature and velocity of metal flow were obtained.The results are basically consistent with the experiment,which indicates that this method may successfully predict the defects in the actual extrusion process.
基金supported by the Shanghai Key Basic Research Program of China (Grant No. 07JC14001)
文摘Ditching is considered as one of the important aspects of safety performances of airplanes. It is related primarily with the fluid-solid interaction, whose studies mainly depend on experiments at the present time. Numerical and analytical methods for fluid-solid interaction by using 3-D full scale airplane＇s model will reduce the dependence on the expensive model tests. Numerical studies can be used to estimate the safety of ditching and provide a reference for the crashworthiness design. This article proposes a 3-D dynamical structural model after the real shape of an airplane and an Arbitrary Lagrange-Euler （ALE） fluid-field model, to simulate the fluid-solid interactions caused by low speed ditching. The simulation is based on interaction computational methods, within LS-DYNA nonlinear finite-element code. The results of pressure distributions and accelerating time histories of the airplane＇s subfloor are discussed in the context of the safety of ditching, and the simulation results and the analytical methods are verified.
文摘A numerical study was conducted for the vortex-induced vibrations of anelastic circular cylinder at low Reynolds numbers. An Arbitrary Lagrangian-Eulerian (ALE) method wasemployed to deal with the fluid-structure interaction with an H-O type of non-staggered gridsincorporating the domain decomposition method (DDM), which could save the computational CPU time dueto re-meshing. The computational domain was divided into nine sub-domains including one ALEsub-domain and eight Eulerian sub-domains. The convection term and dissipation term in the N-Sequations were discretized using the third-order upwind compact scheme and the fourth-order centralcompact scheme, respectively. The motion of the cylinder was modeled by a spring-damper-mass systemand solved using the Runge-Kutta method. By simulating the non-linear fluid-structure interaction,the ''lock-in'', ''beating'' and ''phase switch'' phenomena were successfully captured, and the resultsagree with experimental data Furthermore, the vortex structure, the unsteady lift and drag on thecylinder, and the cylinder displacement at various natural frequency of the cylinder for Re = 200were discussed in detail, by which a jump transition of the wake structure was captured.
文摘Non-equal channel lateral extrusion（NECLE） is a new process that can be used to attain higher grain refinement in comparison with equal channel lateral extrusion（ECLE）. The die design for this process was numerically and experimentally studied. After finding a good correlation between the numerical and experimental results, more comprehensive FE analyses were carried out. Different die geometrical parameters were considered and their effects on the induced plastic strain, stress distribution, velocity field and forming load of the process were investigated. It was found that by this process with a suitable set of die geometrical parameters, higher induced effective strain and more homogeneous strain distribution could be achieved in comparison with ECLE operation.
文摘Based on the theory of optimization,we use edges and angles of cells to represent the geometric quality of computational grids,employ the local gradients of the flow variables to describe the variation of flow field,and construct a multi-objective programming model.The solution of this optimization problem gives appropriate balance between the geometric quality and adaptation of grids.By solving the optimization problem,we propose a new grid rezoning method,which not only keeps good geometric quality of grids,but also can track rapid changes in the flow field.In particular,it performs well for some complex concave domains with corners.We also incorporate the rezoningmethod into anArbitrary Lagrangian-Eulerian(ALE)method which is widely used in the simulation of high-speed multi-material flows.The proposed rezoning and ALE methods of this paper are tested by a number of numerical examples with complex concave domains and compared with some other rezoning methods.The numerical results validate the robustness of the proposed methods.
