For the processor working in the radiation environment in space, it tends to suffer from the single event effect on circuits and system failures, due to cosmic rays and high energy particle radiation. Therefore, the r...For the processor working in the radiation environment in space, it tends to suffer from the single event effect on circuits and system failures, due to cosmic rays and high energy particle radiation. Therefore, the reliability of the processor has become an increasingly serious issue. The BCH-based error correction code can correct multibit errors, but it introduces large latency overhead. This paper proposes a hybrid error correction approach that combines BCH and EDAC to correct both multi-bit and single-bit errors for caches with low cost. The proposed technique can correct up to four-bit error, and correct single-bit error in one cycle. Evaluation results show that, the proposed hybrid error-correction scheme can improve the performance of cache accesses up to 20% compared to the pure BCH scheme.展开更多
This paper explores the impact of back-gate bias (V_(soi)) and supply voltage (V_(DD)) on the single-event upset (SEU) cross section of 0.18μm configurable silicon-on-insulator static random-access memory (SRAM) unde...This paper explores the impact of back-gate bias (V_(soi)) and supply voltage (V_(DD)) on the single-event upset (SEU) cross section of 0.18μm configurable silicon-on-insulator static random-access memory (SRAM) under high linear energy transfer heavyion experimentation.The experimental findings demonstrate that applying a negative back-gate bias to NMOS and a positive back-gate bias to PMOS enhances the SEU resistance of SRAM.Specifically,as the back-gate bias for N-type transistors(V_(nsoi)) decreases from 0 to-10 V,the SEU cross section decreases by 93.23%,whereas an increase in the back-gate bias for P-type transistors (V_(psoi)) from 0 to 10 V correlates with an 83.7%reduction in SEU cross section.Furthermore,a significant increase in the SEU cross section was observed with increase in supply voltage,as evidenced by a 159%surge at V_(DD)=1.98 V compared with the nominal voltage of 1.8 V.To explore the physical mechanisms underlying these experimental data,we analyzed the dependence of the critical charge of the circuit and the collected charge on the bias voltage by simulating SEUs using technology computer-aided design.展开更多
AZ31-4.6% Mg2Si （mass fraction） composite was prepared by conventional casting method. Repetitive upsetting （RU） was applied to severely deforming the as-cast composite at 400 ℃ for 1, 3, and 5 passes. Finite ele...AZ31-4.6% Mg2Si （mass fraction） composite was prepared by conventional casting method. Repetitive upsetting （RU） was applied to severely deforming the as-cast composite at 400 ℃ for 1, 3, and 5 passes. Finite element analysis of the material flow indicates that deformation concentrates in the bottom region of the sample after 1 pass, and much more uniform deformation is obtained after 5 passes. During multi-pass RU process, both dendritic and Chinese script type Mg2Si phases are broken up into smaller particles owing to the shear stress forced by the matrix. With the increasing number of RU passes, finer grain size and more homogeneous distribution of Mg2Si particles are obtained along with significant enhancement in both strength and ductility. AZ31-4.6%Mg2Si composite exhibits tensile strength of 284 MPa and elongation of 9.8%after 5 RU passes at 400 ℃ compared with the initial 128 MPa and 5.4%of original AZ31-4.6%Mg2Si composite.展开更多
We study the problem of multiple node upset （MNU） using three-dimensional device simulation. The results show the transient floating node and charge lateral diffusion are the key reasons for MNU. We compare the MNU ...We study the problem of multiple node upset （MNU） using three-dimensional device simulation. The results show the transient floating node and charge lateral diffusion are the key reasons for MNU. We compare the MNU with multiple bit upset （MBU）,and find that their characteristics are different. Methods to avoid MNU are also discussed.展开更多
Three-dimensional integrated circuits(3D ICs)have entered into the mainstream due to their high performance,high integration,and low power consumption.When used in atmospheric environments,3D ICs are irradiated inevit...Three-dimensional integrated circuits(3D ICs)have entered into the mainstream due to their high performance,high integration,and low power consumption.When used in atmospheric environments,3D ICs are irradiated inevitably by neutrons.In this paper,a 3D die-stacked SRAM device is constructed based on a real planar SRAM device.Then,the single event upsets(SEUs)caused by neutrons with different energies are studied by the Monte Carlo method.The SEU cross-sections for each die and for the whole three-layer die-stacked SRAM device is obtained for neutrons with energy ranging from 1 MeV to 1000 MeV.The results indicate that the variation trend of the SEU cross-section for every single die and for the entire die-stacked device is consistent,but the specific values are different.The SEU cross-section is shown to be dependent on the threshold of linear energy transfer(LETth)and thickness of the sensitive volume(Tsv).The secondary particle distribution and energy deposition are analyzed,and the internal mechanism that is responsible for this difference is illustrated.Besides,the ratio and patterns of multiple bit upset(MBU)caused by neutrons with different energies are also presented.This work is helpful for the aerospace IC designers to understand the SEU mechanism of 3D ICs caused by neutrons irradiation.展开更多
Heavy ion-induced single event upsets(SEUs)of static random access memory(SRAM), integrated with three-dimensional integrated circuit technology, are evaluated using a Monte Carlo simulation method based on the Geant4...Heavy ion-induced single event upsets(SEUs)of static random access memory(SRAM), integrated with three-dimensional integrated circuit technology, are evaluated using a Monte Carlo simulation method based on the Geant4 simulation toolkit. The SEU cross sections and multiple cell upset(MCU) susceptibility of 3D SRAM are explored using different types and energies of heavy ions.In the simulations, the sensitivities of different dies of 3D SRAM show noticeable discrepancies for low linear energy transfers(LETs). The average percentage of MCUs of 3D SRAM increases from 17.2 to 32.95%, followed by the energy of ^(209)Bi decreasing from 71.77 to 38.28 MeV/u. For a specific LET, the percentage of MCUs presents a notable difference between the face-to-face and back-toface structures. In the back-to-face structure, the percentage of MCUs increases with a deeper die, compared with the face-to-face structure. The simulation method and process are verified by comparing the SEU cross sections of planar SRAM with experimental data. The upset cross sections of the planar process and 3D integrated SRAM are analyzed. The results demonstrate that the 3D SRAM sensitivity is not greater than that of the planar SRAM. The 3D process technology has the potential to be applied to the aerospace and military fields.展开更多
Experimental evidence is presented relevant to the angular dependences of multiple-bit upset （MBU） rates and patterns in static random access memories （SRAMs） under heavy ion irradiation. The single event upset （...Experimental evidence is presented relevant to the angular dependences of multiple-bit upset （MBU） rates and patterns in static random access memories （SRAMs） under heavy ion irradiation. The single event upset （SEU） cross sections under tilted ion strikes are overestimated by 23.9%-84.6%, compared with under normally incident ion with the equivalent linear energy transfer （LET） value of 41 MeV/（mg/cm2）, which can be partially explained by the fact that the MBU rate for tilted ions of 30° is 8.5%-9.8% higher than for normally incident ions. While at a lower LET of - 9.5 MeV/（mg/cm2）, no clear discrepancy is observed. Moreover, since the ion trajectories at normal and tilted incidences are different, the predominant double-bit upset （DBU） patterns measured are different in both conditions. Those differences depend on the LET values of heavy ions and devices under test. Thus, effective LET method should be used carefully in ground-based testing of single event effects （SEE） sensitivity, especially in MBU-sensitive devices.展开更多
The instantaneous reversible soft logic upset induced by the electromagnetic interference（EMI） severely affects the performances and reliabilities of complementary metal–oxide–semiconductor（CMOS） inverters. This...The instantaneous reversible soft logic upset induced by the electromagnetic interference（EMI） severely affects the performances and reliabilities of complementary metal–oxide–semiconductor（CMOS） inverters. This kind of soft logic upset is investigated in theory and simulation. Physics-based analysis is performed, and the result shows that the upset is caused by the non-equilibrium carrier accumulation in channels, which can ultimately lead to an abnormal turn-on of specific metal–oxide–semiconductor field-effect transistor（MOSFET） in CMOS inverter. Then a soft logic upset simulation model is introduced. Using this model, analysis of upset characteristic reveals an increasing susceptibility under higher injection powers, which accords well with experimental results, and the influences of EMI frequency and device size are studied respectively using the same model. The research indicates that in a range from L waveband to C waveband, lower interference frequency and smaller device size are more likely to be affected by the soft logic upset.展开更多
We investigate the impact of heavy ion irradiation on a hypothetical static random access memory （SRAM） device. Influences of the irradiation angle, critical charge, drain-drain spacing, and dimension of device stru...We investigate the impact of heavy ion irradiation on a hypothetical static random access memory （SRAM） device. Influences of the irradiation angle, critical charge, drain-drain spacing, and dimension of device structure on the device sensitivity have been studied. These prediction and simulated results are interpreted with MUFPSA, a Monte Carlo code based on Geant4. The results show that the orientation of ion beams and device with different critical charge exert indis- pensable effects on multiple-bit upsets （MBUs）, and that with the decrease in spacing distance between adjacent cells or the dimension of the cells, the device is more susceptible to single event effect, especially to MBUs at oblique incidence.展开更多
文摘For the processor working in the radiation environment in space, it tends to suffer from the single event effect on circuits and system failures, due to cosmic rays and high energy particle radiation. Therefore, the reliability of the processor has become an increasingly serious issue. The BCH-based error correction code can correct multibit errors, but it introduces large latency overhead. This paper proposes a hybrid error correction approach that combines BCH and EDAC to correct both multi-bit and single-bit errors for caches with low cost. The proposed technique can correct up to four-bit error, and correct single-bit error in one cycle. Evaluation results show that, the proposed hybrid error-correction scheme can improve the performance of cache accesses up to 20% compared to the pure BCH scheme.
基金supported by the National Key Laboratory of Materials Behavior and Evaluation Technology in Space Environment(No.6142910220208)National Natural Science Foundation of China(Nos.12105341 and 12035019)the opening fund of Key Laboratory of Silicon Device and Technology,Chinese Academy of Sciences(No.KLSDTJJ2022-3).
文摘This paper explores the impact of back-gate bias (V_(soi)) and supply voltage (V_(DD)) on the single-event upset (SEU) cross section of 0.18μm configurable silicon-on-insulator static random-access memory (SRAM) under high linear energy transfer heavyion experimentation.The experimental findings demonstrate that applying a negative back-gate bias to NMOS and a positive back-gate bias to PMOS enhances the SEU resistance of SRAM.Specifically,as the back-gate bias for N-type transistors(V_(nsoi)) decreases from 0 to-10 V,the SEU cross section decreases by 93.23%,whereas an increase in the back-gate bias for P-type transistors (V_(psoi)) from 0 to 10 V correlates with an 83.7%reduction in SEU cross section.Furthermore,a significant increase in the SEU cross section was observed with increase in supply voltage,as evidenced by a 159%surge at V_(DD)=1.98 V compared with the nominal voltage of 1.8 V.To explore the physical mechanisms underlying these experimental data,we analyzed the dependence of the critical charge of the circuit and the collected charge on the bias voltage by simulating SEUs using technology computer-aided design.
基金Projects(51074106,51374145)supported by the National Natural Science Foundation of ChinaProject(09JC1408200)supported by the Science and Technology Commission of Shanghai Municipality,China+1 种基金Project(2014M561466)supported by China Postdoctoral Science FoundationProject(14R21411000)supported by Shanghai Postdoctoral Scientific Program,China
文摘AZ31-4.6% Mg2Si （mass fraction） composite was prepared by conventional casting method. Repetitive upsetting （RU） was applied to severely deforming the as-cast composite at 400 ℃ for 1, 3, and 5 passes. Finite element analysis of the material flow indicates that deformation concentrates in the bottom region of the sample after 1 pass, and much more uniform deformation is obtained after 5 passes. During multi-pass RU process, both dendritic and Chinese script type Mg2Si phases are broken up into smaller particles owing to the shear stress forced by the matrix. With the increasing number of RU passes, finer grain size and more homogeneous distribution of Mg2Si particles are obtained along with significant enhancement in both strength and ductility. AZ31-4.6%Mg2Si composite exhibits tensile strength of 284 MPa and elongation of 9.8%after 5 RU passes at 400 ℃ compared with the initial 128 MPa and 5.4%of original AZ31-4.6%Mg2Si composite.
文摘We study the problem of multiple node upset （MNU） using three-dimensional device simulation. The results show the transient floating node and charge lateral diffusion are the key reasons for MNU. We compare the MNU with multiple bit upset （MBU）,and find that their characteristics are different. Methods to avoid MNU are also discussed.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12035019,111690041,and 11675233)the Project of Science and Technology on Analog Integrated Circuit Laboratory,China(Grant No.6142802WD201801).
文摘Three-dimensional integrated circuits(3D ICs)have entered into the mainstream due to their high performance,high integration,and low power consumption.When used in atmospheric environments,3D ICs are irradiated inevitably by neutrons.In this paper,a 3D die-stacked SRAM device is constructed based on a real planar SRAM device.Then,the single event upsets(SEUs)caused by neutrons with different energies are studied by the Monte Carlo method.The SEU cross-sections for each die and for the whole three-layer die-stacked SRAM device is obtained for neutrons with energy ranging from 1 MeV to 1000 MeV.The results indicate that the variation trend of the SEU cross-section for every single die and for the entire die-stacked device is consistent,but the specific values are different.The SEU cross-section is shown to be dependent on the threshold of linear energy transfer(LETth)and thickness of the sensitive volume(Tsv).The secondary particle distribution and energy deposition are analyzed,and the internal mechanism that is responsible for this difference is illustrated.Besides,the ratio and patterns of multiple bit upset(MBU)caused by neutrons with different energies are also presented.This work is helpful for the aerospace IC designers to understand the SEU mechanism of 3D ICs caused by neutrons irradiation.
基金supported by the Fundamental Research Funds for the Central Universities(No.HIT.KISTP.201404)Harbin science and innovation research special fund(No.2015RAXXJ003)Special fund for development of Shenzhen strategic emerging industries(No.JCYJ20150625142543456)
文摘Heavy ion-induced single event upsets(SEUs)of static random access memory(SRAM), integrated with three-dimensional integrated circuit technology, are evaluated using a Monte Carlo simulation method based on the Geant4 simulation toolkit. The SEU cross sections and multiple cell upset(MCU) susceptibility of 3D SRAM are explored using different types and energies of heavy ions.In the simulations, the sensitivities of different dies of 3D SRAM show noticeable discrepancies for low linear energy transfers(LETs). The average percentage of MCUs of 3D SRAM increases from 17.2 to 32.95%, followed by the energy of ^(209)Bi decreasing from 71.77 to 38.28 MeV/u. For a specific LET, the percentage of MCUs presents a notable difference between the face-to-face and back-toface structures. In the back-to-face structure, the percentage of MCUs increases with a deeper die, compared with the face-to-face structure. The simulation method and process are verified by comparing the SEU cross sections of planar SRAM with experimental data. The upset cross sections of the planar process and 3D integrated SRAM are analyzed. The results demonstrate that the 3D SRAM sensitivity is not greater than that of the planar SRAM. The 3D process technology has the potential to be applied to the aerospace and military fields.
基金supported by the National Natural Science Foundation of China(Grant Nos.11179003,10975164,10805062,and 11005134)
文摘Experimental evidence is presented relevant to the angular dependences of multiple-bit upset （MBU） rates and patterns in static random access memories （SRAMs） under heavy ion irradiation. The single event upset （SEU） cross sections under tilted ion strikes are overestimated by 23.9%-84.6%, compared with under normally incident ion with the equivalent linear energy transfer （LET） value of 41 MeV/（mg/cm2）, which can be partially explained by the fact that the MBU rate for tilted ions of 30° is 8.5%-9.8% higher than for normally incident ions. While at a lower LET of - 9.5 MeV/（mg/cm2）, no clear discrepancy is observed. Moreover, since the ion trajectories at normal and tilted incidences are different, the predominant double-bit upset （DBU） patterns measured are different in both conditions. Those differences depend on the LET values of heavy ions and devices under test. Thus, effective LET method should be used carefully in ground-based testing of single event effects （SEE） sensitivity, especially in MBU-sensitive devices.
基金supported by the National Natural Science Foundation of China(Grant No.60776034)the Open Fund of Key Laboratory of Complex Electromagnetic Environment Science and Technology,China Academy of Engineering Physics(Grant No.2015-0214.XY.K)
文摘The instantaneous reversible soft logic upset induced by the electromagnetic interference（EMI） severely affects the performances and reliabilities of complementary metal–oxide–semiconductor（CMOS） inverters. This kind of soft logic upset is investigated in theory and simulation. Physics-based analysis is performed, and the result shows that the upset is caused by the non-equilibrium carrier accumulation in channels, which can ultimately lead to an abnormal turn-on of specific metal–oxide–semiconductor field-effect transistor（MOSFET） in CMOS inverter. Then a soft logic upset simulation model is introduced. Using this model, analysis of upset characteristic reveals an increasing susceptibility under higher injection powers, which accords well with experimental results, and the influences of EMI frequency and device size are studied respectively using the same model. The research indicates that in a range from L waveband to C waveband, lower interference frequency and smaller device size are more likely to be affected by the soft logic upset.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 11179003, 10975164, 10805062, and 11005134)
文摘We investigate the impact of heavy ion irradiation on a hypothetical static random access memory （SRAM） device. Influences of the irradiation angle, critical charge, drain-drain spacing, and dimension of device structure on the device sensitivity have been studied. These prediction and simulated results are interpreted with MUFPSA, a Monte Carlo code based on Geant4. The results show that the orientation of ion beams and device with different critical charge exert indis- pensable effects on multiple-bit upsets （MBUs）, and that with the decrease in spacing distance between adjacent cells or the dimension of the cells, the device is more susceptible to single event effect, especially to MBUs at oblique incidence.
