Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic...Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic source.Alternatively,laser interferometry with picometer-scale motional displacement detection can rapidly and precisely measure sound-induced minute vibrations on remote surfaces.Here,we demonstrate the feasibility of sound detection up to 100 kHz at remote sites with≈60 m optical path length via laser homodyne interferometry.Based on our ultrastable hertz linewidth laser with 10-15 fractional stability,our laser interferometer achieves 0.5 pm/Hz1/2 displacement sensitivity near 10 kHz,bounded only by laser frequency noise over 10 kHz.Between 140 Hz and 15 kHz,we achieve a homodyne acoustic sensing sensitivity of subnanometer/Pascal across our conversational frequency overtones.The minimal sound pressure detectable over 60 m optical path length is≈2 mPa,with dynamic ranges over 100 dB.With the demonstrated standoff picometric distance metrology,we successfully detected and reconstructed musical scores of normal conversational volumes with high fidelity.The acoustic detection via this precision laser interferometer could be applied to selective area sound sensing for remote acoustic metrology,optomechanical vibrational motion sensing,and ultrasensitive optical microphones at the laser frequency noise limits.展开更多
The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to inves...The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to investigate the gas dynamics of the bridge film after SCB plasma extinction.Interferometric images of the SCB film gas were obtained through a laser interferometry optical path.After the degradation model of digital image processing,clearer images were produced to facilitate analysis and calculation.The results show that the gas temperature at the center of the SCB film reaches a maximum of 1000 K,and the temperature rapidly decreases along the axial direction of the bridge surface to room temperature at 300 K.The maximum diffusion velocity of the plasma is 1.8 km/s.These findings provide critical insights for SCB design and ignition control.展开更多
High harmonic generation(HHG)provides an experimental method for producing attosecond pulses and probing electron dynamics.Achieving precise dipole phase measurements is critical for tailoring the harmonic emission ph...High harmonic generation(HHG)provides an experimental method for producing attosecond pulses and probing electron dynamics.Achieving precise dipole phase measurements is critical for tailoring the harmonic emission phase and identifying the HHG mechanism.However,achieving this feature by applying traditional two-beam far-field interferometry to solid materials remains challenging.In this study,we present a novel interferometric approach that utilizes a single laser beam to excite two ZnO microwires(MWs)simultaneously,thereby generating coherent high-harmonic sources that form interference fringes in the far-field region.We leverage the diameter-dependent field-enhancement effect in MWs to measure the intensity-dependent fringe shift,revealing that the intraband current mechanism dominates the below-bandgap harmonic,whereas the interband polarization mechanism dominates the above-bandgap harmonic.This study offers a robust method for measuring the dipole phase of solid-state HHG and inspires intensity-modulated high-harmonic applications in coherent imaging and microdevice design.展开更多
Pitch is one of the most important auditory perception characteristics of sound; however, the mechanism underlying the pitch perception of sound is unclear. Although theoretical researches have suggested that percepti...Pitch is one of the most important auditory perception characteristics of sound; however, the mechanism underlying the pitch perception of sound is unclear. Although theoretical researches have suggested that perception of virtual pitch is connected with physics in cochlea of inner ear, there is no direct experimental observation of virtual pitch processing in the cochlea. By laser interferometry, we observe shift phenomena of virtual pitch in basilar membrane vibration of exsomatized cochlea, which is consistent with perceptual pitch shift observed in psychoacoustic experiments. This means that the complex mechanical vibration of basilar membrane in cochlea plays an important role in pitch information processing during hearing.展开更多
Precision measurement tools are compulsory to reduce measurement errors or machining errors in the processes of calibration and manufacturing.The laser interferometer is one of the most important measurement tools inv...Precision measurement tools are compulsory to reduce measurement errors or machining errors in the processes of calibration and manufacturing.The laser interferometer is one of the most important measurement tools invented in the 20th century.Today,it is commonly used in ultraprecision machining and manufacturing,ultraprecision positioning control,and many noncontact optical sensing technologies.So far,the state-of-the-art laser interferometers are the ground-based gravitational-wave detectors,e.g.the Laser Interferometer Gravitational-wave Observatory(LIGO).The LIGO has reached the measurement quantum limit,and some quantum technologies with squeezed light are currently being tested in order to further decompress the noise level.In this paper,we focus on the laser interferometry developed for space-based gravitational-wave detection.The basic working principle and the current status of the key technologies of intersatellite laser interferometry are introduced and discussed in detail.The launch and operation of these large-scale,gravitational-wave detectors based on space-based laser interferometry is proposed for the 2030s.展开更多
The fundamental measurement of space gravitational wave detection is to monitor the relative motion between pairs of freely falling test masses using heterodyne laser interferometry to a precision of 10 pm. The masses...The fundamental measurement of space gravitational wave detection is to monitor the relative motion between pairs of freely falling test masses using heterodyne laser interferometry to a precision of 10 pm. The masses under test are millions of kilometers apart. The inter-spacecraft laser interferometry telescope deliver laser efficiently from one spacecraft to another. It is an important component of the gravitational wave detection observatory. It needs to meet the requirements of large compression ratio, high image quality and extraordinary stray light suppression ability. Based on the primary aberration theory, the method of the large compression ratio off-axis four-mirror optical system design is explored. After optimization, the system has an entrance pupil of 200 mm, compression ratio of 40 times, scientific field of view (FOV) of ±8 μrad. To facilitate suppressing the stray light and delivering the laser beam to the back-end scientific interferometers, the intermediate images and the real exit pupils are spatially available. Over the full FOV, the maximum root mean square (RMS) wavefront error is less than 0.007λ, PV value is less than 0.03λ (λ = 1064 nm). The image quality is approached to the diffraction-limit. The TTL noise caused by the wavefront error of the telescope is analyzed. The TTL noise in the image space of 300 μrad range is less than 1 × 10-10 m whose slope is lower than 0.6 μm/rad, which is under the noise budget of the laser interferometer space antenna (LISA), satisfying the requirements of space gravitational wave detection.展开更多
In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied ...In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied to extract reversion point in the self-mixing interference signal, thus the pulse wave profile is successfully reconstructed. Considering the blood pressure values are intrinsically related to characteristic parameters of the pulse wave, 80 samples from the MIMIC-II database are used to train the extreme learning machine blood pressure model. In the experiment, 15 measured samples of pulse wave signal are used as the prediction sets. The results show that the errors of systolic and diastolic blood pressure are both within 5 mm Hg compared with that by the Coriolis method.展开更多
We present the thermal expansion coefficient （TEC） measurement technology of compensating for the effect of variations in the refractive index based on a Nd： YA G laser feedback system, the beam frequency is shifte...We present the thermal expansion coefficient （TEC） measurement technology of compensating for the effect of variations in the refractive index based on a Nd： YA G laser feedback system, the beam frequency is shifted by a pair of aeousto-optic modulators and then the heterodyne phase measurement technique is used. The sample measured is placed in a muffle furnace with two coaxial holes opened on the opposite furnace walls. The measurement beams hit perpendicularly and coaxially on each surface of the sample. The reference beams hit on the reference mirror and the high-refiectivity mirror, respectively. By the heterodyne configuration and computing, the influences of the vibration, distortion of the sample supporter and the effect of variations in the refractive index are measured and largely minimized. For validation, the TECs of aluminum samples are determined in the temperature range of 29-748K, confirming not only the precision within 5 × 10-7 K-1 and the accuracy within 0.4% from 298K to 448K but also the high sensitivity non-contact measurement of the lower reflectivity surface induced by the sample oxidization from 448 K to 748 K.展开更多
The laser speckle interferometry approach provides the possibility of an in situ optical noncontacted measurement for the surface morphology of plasma facing components(PFCs),and the reconstruction image of the PFC su...The laser speckle interferometry approach provides the possibility of an in situ optical noncontacted measurement for the surface morphology of plasma facing components(PFCs),and the reconstruction image of the PFC surface morphology is computed by a numerical model based on a phase unwrapping algorithm.A remote speckle interferometry measurement at a distance of three meters for real divertor tiles retired from EAST was carried out in the laboratory to simulate a real detection condition on EAST.The preliminary surface morphology of the divertor tiles was well reproduced by the reconstructed geometric image.The feasibility and reliability of this approach for the real-time measurement of PFCs have been demonstrated.展开更多
To implement on-line, real-time monitoring for the surface morphology of Plasma-Facing Materials(PFMs) in tokamak, we developed a Laser Speckle Interferometry measurement approach. A laser ablation method was used to ...To implement on-line, real-time monitoring for the surface morphology of Plasma-Facing Materials(PFMs) in tokamak, we developed a Laser Speckle Interferometry measurement approach. A laser ablation method was used to simulate the erosion process during Plasma-Wall Interactions in a tokamak. In the present investigation, we evaluated the results of laser ablation morphology changes on the surface of Mo material reconstructed by four different approaches(Flood-fill, Quality-guided, Discrete Cosine Transform(DCT) and Weighted-DCT). The morphology results measured by the weighted-DCT approach are very close to the measurement results from confocal microscopy with an average error rate within 7%. It is verified that the weighted-DCT algorithm has high accuracy and can efficiently reduce the influence of noise pollution coming from laser ablation, which is used as a proxy for erosion from plasma wall interaction. Additionally, the CPU computer time has been shortened. This is of great significance for the real-time monitoring of PFMs’ morphology in the Experimental Advanced Superconducting Tokamak(EAST) in the future.展开更多
A new method of receiving laser interferometric measuring signals, that is, method of three photoelectric cells, is presented. The advantages and favorable conditions of the method are analyzed and discussed thoroughl...A new method of receiving laser interferometric measuring signals, that is, method of three photoelectric cells, is presented. The advantages and favorable conditions of the method are analyzed and discussed thoroughly. This method has been successfully applied in the high precision laser interferometer.展开更多
The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can obse...The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can observe the deformation of samples under pressure in the lab and study the anomaly characteristics relating to different strain fields in different fracture-developing areas; while by using RDI, we can observe the landform and surface deformation. The results of deformation observed before and after the Ms=7.9 Mani earthquake （Tibet） and Ms=6.2 Shangyi-Zhangbei earthquake in China are obtained. It is pointed out that LRTHI and RDi are similar, which study the characteristics of anomalous deformation field by fringe variations for both of them. Therefore, the observation of deformation field in the seismogenic process, especially in the period impending an earthquake by RDI, and the comparative study in the lab by LRTHI are of great significance.展开更多
By means of a double mirror interferometry a two-dimensional temperature distribution measurement in convective thermal boundary layers is presented. When the cold air flows along a hot plate model, the interferometri...By means of a double mirror interferometry a two-dimensional temperature distribution measurement in convective thermal boundary layers is presented. When the cold air flows along a hot plate model, the interferometric fringe inside the boundary layer will bend. According to the displacement of the fringe and the relation between temperature and index of refraction, a two-dimensional temperature profile is obtained. All is accomplished by optical device with the help of micro-computer without any contact with the flow field.展开更多
Laser Ultrasonic Testing(LUT)holds great promise for industrial applications,particularly in Nondestructive Testing(NDT)of aerospace composites.It offers advantages such as non-contact,high-resolution,and real-time de...Laser Ultrasonic Testing(LUT)holds great promise for industrial applications,particularly in Nondestructive Testing(NDT)of aerospace composites.It offers advantages such as non-contact,high-resolution,and real-time defect detection.Traditional NDT methods struggle with the complex shapes of structural parts and in-situ testing,limiting their detection efficiency and sensitivity.We review the principles of excitation,optical detection,and laser parameter selection for LUT.It also compares applicability of LUT with other NDT techniques.We discuss strengths and limitations of LUT in detecting defects,characterizing material properties,and monitoring the health of aerospace composites.LUT has proven effective in detecting defects in aerospace materials under extreme conditions such as high temperature and pressure during manufacturing and service.However,challenges remain in defect localization,rapid identification,signal extraction in noisy environments,and micro-defect characterization.Despite these limitations,LUT stands out for its non-contact real-time capabilities and its ability to detect defects in harsh industrial conditions.This paper enhances the understanding for potential and future development of LUT,including improvements in laser generators,non-contact inspection equipment,modular inspection device design,and high-accuracy real-time inspection technologies.展开更多
Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive s...Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive spectral interferometry(DSI)shows promise for high-speed precision measurements,whereas the resolution of subnanometers has not yet been achieved.We present a comprehensive theoretical framework to analyze the limitations of real-time DSI based on the signal-to-noise ratio and data volume.A real-time orthogonal polarization spectral interferometry technique is proposed,which utilizes a pair of interferograms with the pi-phase shift to effectively mitigate the phase noise embedded in real-time spectral envelopes,thereby enabling the precise measurements with subnanometer resolution at megahertz frame rates.The recorded time series data are processed through interpolation,segmentation,time–frequency mapping,and de-enveloping to regain the typical cosine-shaped spectral evolution,followed by a fitting-based phase retrieval method to extract the interference phase.The phase resolution of 1.1 mrad(0.91 as for time delay and 0.3 nm for distance)is obtained at the update rate of 22.2 MHz even under the detection bandwidth of 500 MHz,and can be further enhanced to 0.29 mrad(0.24 as for time delay)after 500 times averaging(∼0.5 MHz).Our approach is validated through periodic phase modulations and applied to measure the rapid damped oscillations of a piezo stage,yielding results consistent with those obtained from a commercial picometer interferometer.展开更多
基金supported by the Office of Naval Research(Grant Nos.N00014-16-1-2094 and N00014-24-1-2547)the Lawrence Livermore National Laboratory(Grant No.B622827)the National Science Foundation.Y.-S.J.acknowledges support from KRISS(Grant Nos.25011026 and 25011211).
文摘Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic source.Alternatively,laser interferometry with picometer-scale motional displacement detection can rapidly and precisely measure sound-induced minute vibrations on remote surfaces.Here,we demonstrate the feasibility of sound detection up to 100 kHz at remote sites with≈60 m optical path length via laser homodyne interferometry.Based on our ultrastable hertz linewidth laser with 10-15 fractional stability,our laser interferometer achieves 0.5 pm/Hz1/2 displacement sensitivity near 10 kHz,bounded only by laser frequency noise over 10 kHz.Between 140 Hz and 15 kHz,we achieve a homodyne acoustic sensing sensitivity of subnanometer/Pascal across our conversational frequency overtones.The minimal sound pressure detectable over 60 m optical path length is≈2 mPa,with dynamic ranges over 100 dB.With the demonstrated standoff picometric distance metrology,we successfully detected and reconstructed musical scores of normal conversational volumes with high fidelity.The acoustic detection via this precision laser interferometer could be applied to selective area sound sensing for remote acoustic metrology,optomechanical vibrational motion sensing,and ultrasensitive optical microphones at the laser frequency noise limits.
基金supported by the Anhui Zhongchuang Energy New Energy Technology Co.,Ltd.,Entrusted Project.
文摘The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to investigate the gas dynamics of the bridge film after SCB plasma extinction.Interferometric images of the SCB film gas were obtained through a laser interferometry optical path.After the degradation model of digital image processing,clearer images were produced to facilitate analysis and calculation.The results show that the gas temperature at the center of the SCB film reaches a maximum of 1000 K,and the temperature rapidly decreases along the axial direction of the bridge surface to room temperature at 300 K.The maximum diffusion velocity of the plasma is 1.8 km/s.These findings provide critical insights for SCB design and ignition control.
基金supported by the National Key R&D Program of China (Grant Nos.2023YFA1406801 and 2022YFA1604301)the National Natural Science Foundation of China (Grant Nos.12434013,12595343,12404393,and 12174011)。
文摘High harmonic generation(HHG)provides an experimental method for producing attosecond pulses and probing electron dynamics.Achieving precise dipole phase measurements is critical for tailoring the harmonic emission phase and identifying the HHG mechanism.However,achieving this feature by applying traditional two-beam far-field interferometry to solid materials remains challenging.In this study,we present a novel interferometric approach that utilizes a single laser beam to excite two ZnO microwires(MWs)simultaneously,thereby generating coherent high-harmonic sources that form interference fringes in the far-field region.We leverage the diameter-dependent field-enhancement effect in MWs to measure the intensity-dependent fringe shift,revealing that the intraband current mechanism dominates the below-bandgap harmonic,whereas the interband polarization mechanism dominates the above-bandgap harmonic.This study offers a robust method for measuring the dipole phase of solid-state HHG and inspires intensity-modulated high-harmonic applications in coherent imaging and microdevice design.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11374118 and 90820001
文摘Pitch is one of the most important auditory perception characteristics of sound; however, the mechanism underlying the pitch perception of sound is unclear. Although theoretical researches have suggested that perception of virtual pitch is connected with physics in cochlea of inner ear, there is no direct experimental observation of virtual pitch processing in the cochlea. By laser interferometry, we observe shift phenomena of virtual pitch in basilar membrane vibration of exsomatized cochlea, which is consistent with perceptual pitch shift observed in psychoacoustic experiments. This means that the complex mechanical vibration of basilar membrane in cochlea plays an important role in pitch information processing during hearing.
基金the National Natural Science Foundation of China(Grant Nos.11655001,11654004,91836104).
文摘Precision measurement tools are compulsory to reduce measurement errors or machining errors in the processes of calibration and manufacturing.The laser interferometer is one of the most important measurement tools invented in the 20th century.Today,it is commonly used in ultraprecision machining and manufacturing,ultraprecision positioning control,and many noncontact optical sensing technologies.So far,the state-of-the-art laser interferometers are the ground-based gravitational-wave detectors,e.g.the Laser Interferometer Gravitational-wave Observatory(LIGO).The LIGO has reached the measurement quantum limit,and some quantum technologies with squeezed light are currently being tested in order to further decompress the noise level.In this paper,we focus on the laser interferometry developed for space-based gravitational-wave detection.The basic working principle and the current status of the key technologies of intersatellite laser interferometry are introduced and discussed in detail.The launch and operation of these large-scale,gravitational-wave detectors based on space-based laser interferometry is proposed for the 2030s.
文摘The fundamental measurement of space gravitational wave detection is to monitor the relative motion between pairs of freely falling test masses using heterodyne laser interferometry to a precision of 10 pm. The masses under test are millions of kilometers apart. The inter-spacecraft laser interferometry telescope deliver laser efficiently from one spacecraft to another. It is an important component of the gravitational wave detection observatory. It needs to meet the requirements of large compression ratio, high image quality and extraordinary stray light suppression ability. Based on the primary aberration theory, the method of the large compression ratio off-axis four-mirror optical system design is explored. After optimization, the system has an entrance pupil of 200 mm, compression ratio of 40 times, scientific field of view (FOV) of ±8 μrad. To facilitate suppressing the stray light and delivering the laser beam to the back-end scientific interferometers, the intermediate images and the real exit pupils are spatially available. Over the full FOV, the maximum root mean square (RMS) wavefront error is less than 0.007λ, PV value is less than 0.03λ (λ = 1064 nm). The image quality is approached to the diffraction-limit. The TTL noise caused by the wavefront error of the telescope is analyzed. The TTL noise in the image space of 300 μrad range is less than 1 × 10-10 m whose slope is lower than 0.6 μm/rad, which is under the noise budget of the laser interferometer space antenna (LISA), satisfying the requirements of space gravitational wave detection.
基金supported by the National Natural Science Foundation of China (No.61675174)the Natural Science Foundation of Fujian Province (No.2020J01705)。
文摘In this paper, we present a method based on self-mixing interferometry combing extreme learning machine for real-time human blood pressure measurement. A signal processing method based on wavelet transform is applied to extract reversion point in the self-mixing interference signal, thus the pulse wave profile is successfully reconstructed. Considering the blood pressure values are intrinsically related to characteristic parameters of the pulse wave, 80 samples from the MIMIC-II database are used to train the extreme learning machine blood pressure model. In the experiment, 15 measured samples of pulse wave signal are used as the prediction sets. The results show that the errors of systolic and diastolic blood pressure are both within 5 mm Hg compared with that by the Coriolis method.
基金Supported by the National Natural Science Foundation of China under Grant No F050306
文摘We present the thermal expansion coefficient （TEC） measurement technology of compensating for the effect of variations in the refractive index based on a Nd： YA G laser feedback system, the beam frequency is shifted by a pair of aeousto-optic modulators and then the heterodyne phase measurement technique is used. The sample measured is placed in a muffle furnace with two coaxial holes opened on the opposite furnace walls. The measurement beams hit perpendicularly and coaxially on each surface of the sample. The reference beams hit on the reference mirror and the high-refiectivity mirror, respectively. By the heterodyne configuration and computing, the influences of the vibration, distortion of the sample supporter and the effect of variations in the refractive index are measured and largely minimized. For validation, the TECs of aluminum samples are determined in the temperature range of 29-748K, confirming not only the precision within 5 × 10-7 K-1 and the accuracy within 0.4% from 298K to 448K but also the high sensitivity non-contact measurement of the lower reflectivity surface induced by the sample oxidization from 448 K to 748 K.
基金supported by the National Magnetic Confinement Fusion Science Program of China(No.2013GB109005)National Natural Science Foundation of China(Nos.11175035,11475039)Chinesisch-Deutsches Forschungs project(GZ768)
文摘The laser speckle interferometry approach provides the possibility of an in situ optical noncontacted measurement for the surface morphology of plasma facing components(PFCs),and the reconstruction image of the PFC surface morphology is computed by a numerical model based on a phase unwrapping algorithm.A remote speckle interferometry measurement at a distance of three meters for real divertor tiles retired from EAST was carried out in the laboratory to simulate a real detection condition on EAST.The preliminary surface morphology of the divertor tiles was well reproduced by the reconstructed geometric image.The feasibility and reliability of this approach for the real-time measurement of PFCs have been demonstrated.
基金supported by the National Key R&D Program of China (No. 2017YFE0301304)National Natural Science Foundation of China (Nos. 11605023, 11805028, 11705020)+1 种基金China Postdoctoral Science Foundation (Nos. 2017T100172, 2016M591423)the Fundamental Research Funds for the Central Universities (Nos. DUT17RC(4)53, DUT18LK38)
文摘To implement on-line, real-time monitoring for the surface morphology of Plasma-Facing Materials(PFMs) in tokamak, we developed a Laser Speckle Interferometry measurement approach. A laser ablation method was used to simulate the erosion process during Plasma-Wall Interactions in a tokamak. In the present investigation, we evaluated the results of laser ablation morphology changes on the surface of Mo material reconstructed by four different approaches(Flood-fill, Quality-guided, Discrete Cosine Transform(DCT) and Weighted-DCT). The morphology results measured by the weighted-DCT approach are very close to the measurement results from confocal microscopy with an average error rate within 7%. It is verified that the weighted-DCT algorithm has high accuracy and can efficiently reduce the influence of noise pollution coming from laser ablation, which is used as a proxy for erosion from plasma wall interaction. Additionally, the CPU computer time has been shortened. This is of great significance for the real-time monitoring of PFMs’ morphology in the Experimental Advanced Superconducting Tokamak(EAST) in the future.
文摘A new method of receiving laser interferometric measuring signals, that is, method of three photoelectric cells, is presented. The advantages and favorable conditions of the method are analyzed and discussed thoroughly. This method has been successfully applied in the high precision laser interferometer.
基金Joint Seismological Science Foundation of China (201012).
文摘The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can observe the deformation of samples under pressure in the lab and study the anomaly characteristics relating to different strain fields in different fracture-developing areas; while by using RDI, we can observe the landform and surface deformation. The results of deformation observed before and after the Ms=7.9 Mani earthquake （Tibet） and Ms=6.2 Shangyi-Zhangbei earthquake in China are obtained. It is pointed out that LRTHI and RDi are similar, which study the characteristics of anomalous deformation field by fringe variations for both of them. Therefore, the observation of deformation field in the seismogenic process, especially in the period impending an earthquake by RDI, and the comparative study in the lab by LRTHI are of great significance.
文摘By means of a double mirror interferometry a two-dimensional temperature distribution measurement in convective thermal boundary layers is presented. When the cold air flows along a hot plate model, the interferometric fringe inside the boundary layer will bend. According to the displacement of the fringe and the relation between temperature and index of refraction, a two-dimensional temperature profile is obtained. All is accomplished by optical device with the help of micro-computer without any contact with the flow field.
基金co-supported by the Natural Science Foundation of China(NSFC)(Nos.52305139 and 52175124)Zhejiang Provincial Natural Science Foundation,China(Nos.LQ23E050017 and LZ21E050003)+1 种基金the Fundamental Research Funds for the Provincial Universities of Zhejiang,China(No.RF-A2024001)the China Postdoctoral Science Foundation(No.2025M771342)。
文摘Laser Ultrasonic Testing(LUT)holds great promise for industrial applications,particularly in Nondestructive Testing(NDT)of aerospace composites.It offers advantages such as non-contact,high-resolution,and real-time defect detection.Traditional NDT methods struggle with the complex shapes of structural parts and in-situ testing,limiting their detection efficiency and sensitivity.We review the principles of excitation,optical detection,and laser parameter selection for LUT.It also compares applicability of LUT with other NDT techniques.We discuss strengths and limitations of LUT in detecting defects,characterizing material properties,and monitoring the health of aerospace composites.LUT has proven effective in detecting defects in aerospace materials under extreme conditions such as high temperature and pressure during manufacturing and service.However,challenges remain in defect localization,rapid identification,signal extraction in noisy environments,and micro-defect characterization.Despite these limitations,LUT stands out for its non-contact real-time capabilities and its ability to detect defects in harsh industrial conditions.This paper enhances the understanding for potential and future development of LUT,including improvements in laser generators,non-contact inspection equipment,modular inspection device design,and high-accuracy real-time inspection technologies.
基金supported by the National Natural Science Foundation of China(Grant No.61705193)the Natural Science Foundation of Zhejiang Province(Grant No.LGG20F050002)the Jinhua Science and Technology Plan(Project No.2024-1-064).
文摘Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive spectral interferometry(DSI)shows promise for high-speed precision measurements,whereas the resolution of subnanometers has not yet been achieved.We present a comprehensive theoretical framework to analyze the limitations of real-time DSI based on the signal-to-noise ratio and data volume.A real-time orthogonal polarization spectral interferometry technique is proposed,which utilizes a pair of interferograms with the pi-phase shift to effectively mitigate the phase noise embedded in real-time spectral envelopes,thereby enabling the precise measurements with subnanometer resolution at megahertz frame rates.The recorded time series data are processed through interpolation,segmentation,time–frequency mapping,and de-enveloping to regain the typical cosine-shaped spectral evolution,followed by a fitting-based phase retrieval method to extract the interference phase.The phase resolution of 1.1 mrad(0.91 as for time delay and 0.3 nm for distance)is obtained at the update rate of 22.2 MHz even under the detection bandwidth of 500 MHz,and can be further enhanced to 0.29 mrad(0.24 as for time delay)after 500 times averaging(∼0.5 MHz).Our approach is validated through periodic phase modulations and applied to measure the rapid damped oscillations of a piezo stage,yielding results consistent with those obtained from a commercial picometer interferometer.
