Two different poling techniques-corona poling and contact poling in the backdrop of electro-optic （EO） polymer modulators are compared. A 3-layer structure EO polymer modulator is prepared for the poling. The poling...Two different poling techniques-corona poling and contact poling in the backdrop of electro-optic （EO） polymer modulators are compared. A 3-layer structure EO polymer modulator is prepared for the poling. The poling setups and procedures of these two different methods are given. It is found that a well-controlled precure step is very critical, otherwise it will result in either lower poling efficiency or damaged film. Experimental results show that contact poling does not create severe surface damage as corona poling and poling voltage is much lower, but corona poling provides higher EO effect than contact poling. Besides, contact poling can provide poling size as large as the substrate size.展开更多
Passive inter-modulation （PIM） is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communicatio...Passive inter-modulation （PIM） is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform （FFT）, we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.展开更多
A numerical model of thermoelectric module （TEM） is created by academic analysis,and the impacts of the resistance ratio and thermoelement size on the output power and thermoelectric efficiency of the TEM are analyz...A numerical model of thermoelectric module （TEM） is created by academic analysis,and the impacts of the resistance ratio and thermoelement size on the output power and thermoelectric efficiency of the TEM are analyzed by the MATLAB numerical calculation.The numerical model is validated by the ANSYS thermal,electrical,and structural coupling simulation.The effects of the variable physical property parameters and contact effect on the output power and thermoelectric efficiency are evaluated,and the concept of aspect ratio optimal domain is proposed,which provides a new design approach for the TEM.展开更多
Parameter optimization integrating operation parameters and structure parameters for the purpose of high permeate flux,high productivity and low exergy consumption of direct contact membrane distillation (DCMD) proces...Parameter optimization integrating operation parameters and structure parameters for the purpose of high permeate flux,high productivity and low exergy consumption of direct contact membrane distillation (DCMD) process was conducted based on Taguchi experimental design. L16(45) orthogonal experiments were carried out with feed inlet temperature,permeate stream inlet temperature,flow rate,module packing density and length-diameter ratio as optimization parameters and with permeate flux,water productivity per unit volume of module and water production per unit exergy loss separately as optimization objectives. By using range analysis method,the dominance degree of the various influencing factors for the three objectives was analyzed and the optimum condition was obtained for the three objectives separately. Furthermore,the multi-objectives optimization was performed based on a weight grade method. The combined optimum conditions are feed inlet temperature 75℃,packing density 30% ,length-diameter ratio 10,permeate stream inlet temperature 30 ℃ and flow rate 25 L/h,which is in order of their dominance degree,and the validity of the optimization scheme was confirmed.展开更多
文摘Two different poling techniques-corona poling and contact poling in the backdrop of electro-optic （EO） polymer modulators are compared. A 3-layer structure EO polymer modulator is prepared for the poling. The poling setups and procedures of these two different methods are given. It is found that a well-controlled precure step is very critical, otherwise it will result in either lower poling efficiency or damaged film. Experimental results show that contact poling does not create severe surface damage as corona poling and poling voltage is much lower, but corona poling provides higher EO effect than contact poling. Besides, contact poling can provide poling size as large as the substrate size.
文摘Passive inter-modulation （PIM） is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform （FFT）, we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.
基金Funded by Guangdong Natural Science Foundation (No.00355991220615019)
文摘A numerical model of thermoelectric module （TEM） is created by academic analysis,and the impacts of the resistance ratio and thermoelement size on the output power and thermoelectric efficiency of the TEM are analyzed by the MATLAB numerical calculation.The numerical model is validated by the ANSYS thermal,electrical,and structural coupling simulation.The effects of the variable physical property parameters and contact effect on the output power and thermoelectric efficiency are evaluated,and the concept of aspect ratio optimal domain is proposed,which provides a new design approach for the TEM.
文摘Parameter optimization integrating operation parameters and structure parameters for the purpose of high permeate flux,high productivity and low exergy consumption of direct contact membrane distillation (DCMD) process was conducted based on Taguchi experimental design. L16(45) orthogonal experiments were carried out with feed inlet temperature,permeate stream inlet temperature,flow rate,module packing density and length-diameter ratio as optimization parameters and with permeate flux,water productivity per unit volume of module and water production per unit exergy loss separately as optimization objectives. By using range analysis method,the dominance degree of the various influencing factors for the three objectives was analyzed and the optimum condition was obtained for the three objectives separately. Furthermore,the multi-objectives optimization was performed based on a weight grade method. The combined optimum conditions are feed inlet temperature 75℃,packing density 30% ,length-diameter ratio 10,permeate stream inlet temperature 30 ℃ and flow rate 25 L/h,which is in order of their dominance degree,and the validity of the optimization scheme was confirmed.
