As a crucial human activity,dam construction can profoundly impact the surface hydrology patterns.The Three Gorges Reservoir(TGR),as one of the largest hydraulic engineering projects in the world,has gained continuous...As a crucial human activity,dam construction can profoundly impact the surface hydrology patterns.The Three Gorges Reservoir(TGR),as one of the largest hydraulic engineering projects in the world,has gained continuous attention for its eco-hydrological effects.However,further investigation is necessary to understand the runoff and social impacts of the TGR on the Upper Yangtze River.This study first employed a modified SWAT model to simulate runoff,compared scenarios with and without the TGR,and finally evaluated water supply and demand in the Upper Yangtze River.The results showed a significant increasing trend in the surface water area of the Upper Yangtze River from 2000-2020.The modified SWAT model performs well in simulating the runoff,with Nash-Sutcliffe Efficiency and Percent Bias improved by 0.04-0.30 and 2-31.90,respectively.Scenario simulation results revealed that the TGR reduced seasonal differences in runoff.During the flood season,the runoff volume at the Yichang Station in the scenario with the TGR is lower than in the scenario without the TGR,peaking at 4500 m3/s.Conversely,in the dry season,the runoff volume of the scenario with TGR is higher,with a maximum increase of 1500 m3/s.The region exhibiting the greatest runoff variations is the Yangtze River's main stem in the Three Gorges Reservoir region.Besides,the TGR notably alleviated the water supply-demand imbalance in Chongqing during the winter and spring seasons,with a maximum increase of 0.16 in the supplydemand index.This study can contribute significantly to understanding the natural and social impacts of the TGR from the perspective of hydrological and scenario simulation.展开更多
To investigate the performance of utilizing the shape memory effect of SMA(Shape Memory Alloy)wire to generate recovery stress,this paper performed single heating recovery stress tests and reciprocating heating-coolin...To investigate the performance of utilizing the shape memory effect of SMA(Shape Memory Alloy)wire to generate recovery stress,this paper performed single heating recovery stress tests and reciprocating heating-cooling recovery stress tests on SMA wire under varying initial strain conditions.The effects of various strains and different energized heating methods on the recovery stress of SMA wires were explored in the single heating tests.The SMA wire was strained from 2%to 8%initially,and two distinct heating approaches were employed:one using a large current interval for rapid heating and one using a small current interval for slower heating.The experimental outcomes reveal that during a single heating cycle,the temperature-recovery stress relationship of SMA wire exhibits three distinct stages:the martensite phase stage,the transition stage from martensite to austenite phase,and the austenite phase stage.Notably,the choice of heating method does not influence the maximum recovery stress value,and the correlation between initial strain and maximum recovery stress is predominantly linear.Moreover,conducting the reciprocating temperature rise and fall performance test is important to better simulate the scenario in practical engineering where multiple recovery stress in SMA wires for structural repair.In this test,two temperature cycling methods were studied:interval rise and fall,as well as direct rise and fall.In the case of utilizing the interval temperature rise and fall method,it was observed that the recovery stress associated with cooling was significantly higher than that corresponding to heating at the same temperature.Furthermore,the recovery stress was lower upon subsequent heating than that measured during the previous heating cycle.Based on the experimental results,a prediction model for the temperature-recovery stress relationship has been proposed to simplify numerical calculations.It is hoped that an approximate temperaturerecovery stress curve can be obtained from the parameters of the SMA wire.The calculated values derived from this model show good alignment with the measured values,indicating its reliability.展开更多
In this paper, we study a modified Leslie-Gower predator-prey model with Smith growth subject to homogeneous Neumann boundary condition, in which the functional response is the Crowley-Martin functional response term....In this paper, we study a modified Leslie-Gower predator-prey model with Smith growth subject to homogeneous Neumann boundary condition, in which the functional response is the Crowley-Martin functional response term. Firstly, for ODE model, the local stability of equilibrium point is given. And by using bifurcation theory and selecting suitable bifurcation parameters, we find many kinds of bifurcation phenomena, including Transcritical bifurcation and Hopf bifurcation. For the reaction-diffusion model, we find that Turing instability occurs. Besides, it is proved that Hopf bifurcation exists in the model. Finally, numerical simulations are presented to verify and illustrate the theoretical results.展开更多
Warm rotary draw bending provides a feasible method to form the large-diameter thin-walled（LDTW）TC4 bent tubes, which are widely used in the pneumatic system of aircrafts. An accurate prediction of flow behavior of ...Warm rotary draw bending provides a feasible method to form the large-diameter thin-walled（LDTW）TC4 bent tubes, which are widely used in the pneumatic system of aircrafts. An accurate prediction of flow behavior of TC4 tubes considering the couple effects of temperature,strain rate and strain is critical for understanding the deformation behavior of metals and optimizing the processing parameters in warm rotary draw bending of TC4 tubes. In this study, isothermal compression tests of TC4 tube alloy were performed from 573 to 873 K with an interval of 100 K and strain rates of 0.001, 0.010 and0.100 s^（-1）. The prediction of flow behavior was done using two constitutive models, namely modified Arrhenius model and artificial neural network（ANN） model. The predictions of these constitutive models were compared using statistical measures like correlation coefficient（R）, average absolute relative error（AARE） and its variation with the deformation parameters（temperature, strain rate and strain）. Analysis of statistical measures reveals that the two models show high predicted accuracy in terms of R and AARE. Comparatively speaking, the ANN model presents higher predicted accuracy than the modified Arrhenius model. In addition, the predicted accuracy of ANN model presents high stability at the whole deformation parameter ranges, whereas the predictability of the modified Arrhenius model has some fluctuation at different deformation conditions. It presents higher predicted accuracy at temperatures of 573-773 K, strain rates of 0.010-0.100 s^（-1）and strain of 0.04-0.32, while low accuracy at temperature of 873 K, strain rates of 0.001 s^（-1）and strain of 0.36-0.48.Thus, the application of modified Arrhenius model is limited by its relatively low predicted accuracy at some deformation conditions, while the ANN model presents very high predicted accuracy at all deformation conditions,which can be used to study the compression behavior of TC4 tube at the temperature range of 573-873 K and the strain rate of 0.001-0.100 s^（-1）. It can provide guideline for the design of processing parameters in warm rotary draw bending of LDTW TC4 tubes.展开更多
Through modifying the CPN model, a kind of multivariable fuzzy model is put forward, and the matching fuzzy multistep predictive control algorithm is deduced based on the model. The modified model works in a competiti...Through modifying the CPN model, a kind of multivariable fuzzy model is put forward, and the matching fuzzy multistep predictive control algorithm is deduced based on the model. The modified model works in a competitive output manner which results in its local representation property. While studying on line, only a few parameters need to be regulated. So the model has the merits of fast learning and on line self organizing modeling. The control algorithm is simple, adaptive and useful in multivariable and time delay systems. Applying the algorithm in a paper making system, simulation shows its good effect.展开更多
Compaction process simulation and residual stress prediction of green PM compact were carried out with elasto-plastic 3D FEA based on the modified Drueker-Prager Cap model in Abaqus. The model parameters of the invest...Compaction process simulation and residual stress prediction of green PM compact were carried out with elasto-plastic 3D FEA based on the modified Drueker-Prager Cap model in Abaqus. The model parameters of the investigated powder Distaloy AE were determined as functions of relative density through typical mechanical property tests of powder. The model was implemented as a user subroutine USDFLD. Single sided compaction of a d20 ram^5 mm disk green compact of Distaloy AE was simulated, and the residual stress of the disk after ejection was predicted with FEA. The FEA results of the compaction process and the residual stress of the disk show good agreement with compaction experiments and X-ray diffraction measurements, which validates the model and its parameters. The results indicate that the compressive residual stresses exist mainly in a thin layer on the side surface, but the residual stresses are very small on the top and bottom surfaces.展开更多
The hot compressive deformation behaviors of Cu-6wt.%Ag alloy were studied experimentally in the temperature range of 973.1123 K and the strain rate range of 0.01.10 s^-1.The stress increases and reaches the maximum v...The hot compressive deformation behaviors of Cu-6wt.%Ag alloy were studied experimentally in the temperature range of 973.1123 K and the strain rate range of 0.01.10 s^-1.The stress increases and reaches the maximum value when the true strain is very small,and then the stress changes slowly and tends to be stable under the action of work hardening,dynamic recovery and recrystallization.The material parameters of the conventional Arrhenius constitutive model are only related to strain under different deformation conditions,and the prediction error is large,which cannot accurately characterize the hot deformation behavior of the alloy.To describe the hot deformation behavior of the alloy accurately,a modified constitutive model was established by considering the simultaneous influence of forming temperature,strain rate and strain.The results indicate that correlation coefficient(R)and the average absolute relative error(AARE)are 0.993 and 4.2%,respectively.The modified constitutive model can accurately describe the hot deformation behavior of Cu-6wt.%Ag alloy.展开更多
Taking into account the viscoelasticity of the fenugreek gum, a modified Maxwell model in terms of fractional derivatives is developed. Using this model, it is observed that the fenugreek gums with at least two differ...Taking into account the viscoelasticity of the fenugreek gum, a modified Maxwell model in terms of fractional derivatives is developed. Using this model, it is observed that the fenugreek gums with at least two different concentrations obey the Cox-Merz rule.展开更多
Considering the compressibility of the cavity in the cavitating flow, this paper presents a modified k-ω model for predicting the cavitating flow in a centrifugal pump, in which the modified k-ω model and Schnerr-Sa...Considering the compressibility of the cavity in the cavitating flow, this paper presents a modified k-ω model for predicting the cavitating flow in a centrifugal pump, in which the modified k-ω model and Schnerr-Sauer cavitation model were combined with ANSYS CFX. To evaluate the modified and standard k-co models, numerical simulations were performed with these two models, respectively, and the calculation results were compared with the experimental data. Numerical simulations were executed with three different values of the flow coefficient, and the simulation results of the modified k-ω model showed agreement with most of the experimental data. The cavitating flow in the centrifugal pump obtained by the modified k-ω model at the design flow coefficient of 0.102, was analyzed. When the cavitation number decreases, the cavity initially generates on the suction side of the blade near the leading edge and then expands to the outlet of the impeller, and the decrease of the total pressure coefficient mainly occurs upstream of the impeller passage, while the downstream remains almost unaffected by the development of cavitation.展开更多
AIM:To explore the related risk factors for diabetic retinopathy(DR)in type 2 diabetes with insulin therapy.METHODS:We studied the relationships among blood glucose,serum C-peptide,plasma insulin,beta-cell function an...AIM:To explore the related risk factors for diabetic retinopathy(DR)in type 2 diabetes with insulin therapy.METHODS:We studied the relationships among blood glucose,serum C-peptide,plasma insulin,beta-cell function and the development of DR.Beta-cell function was assessed by a modified homeostasis model assessment(modified HOMA)which was gained by using C-peptide to replace insulin in the homeostasis model assessment(HOMA)of beta-cell function.We also studied the relationships between modified HOMA index and serum C-peptide response to 100 g tasteless steamed bread to determine the accuracy of modified HOMA.RESULTS:Our study group consisted of 170 type 2diabetic inpatients with DR(age:58.35±13.87y,mean±SD)and 205 type 2 diabetic inpatients with no DR(NDR)(age:65.52±11.59y).DR patients had higher age,longer diabetic duration,higher hypertension grade,higher postprandial plasma glucose,higher fluctuation level of plasma glucose,lower body mass index(BMI),lower postprandial serum insulin and C-peptide,lower fluctuation level of serum insulin and C-peptide(P【0.05).In our logistic regression model,duration of diabetes,hypertension grade,fasting plasma insulin and glycosylated hemoglobin(HbA1C)were significantly associated with the presence of DR after adjustment for confounding factors(P【0.05).CONCLUSION:Our results suggested although modified HOMA showed significant correlation to the occurrence of DR on Spearman’s rank-correlationanalysis,logistic regression showed no significant association between these two variables after adjustment for relevant confounding factors(such as age,sex,duration of diabetes,BMI,hypertension grade,HbA1C,plasma insulin).Duration of diabetes,hypertension grade,fasting plasma insulin and HbA1C were independently associated with the development of DR in Chinese type 2 diabetics.展开更多
The purpose of this study is to predict the morphologies in the solidification process for Cu-0.6Cr(mass fraction,%)alloy by vacuum continuous casting(VCC)and verify its accuracy by the observed experimental results.I...The purpose of this study is to predict the morphologies in the solidification process for Cu-0.6Cr(mass fraction,%)alloy by vacuum continuous casting(VCC)and verify its accuracy by the observed experimental results.In numerical simulation aspect, finite difference(FD)method and modified cellular automaton(MCA)model were used to simulate the macro-temperature field, micro-concentration field,nucleation and grain growth of Cu-0.6Cr alloy using real data from actual casting operations.From the observed casting experiment,the preliminary grain morphologies are the directional columnar grains by the VCC process.The solidification morphologies by MCAFD model are in agreement with the result of actual casting experiment well.展开更多
The theoretical flame temperature （TFT） before tuyere, always highly concerned by blast furnace （BF） operators, is one of the most important parameters for evaluating the thermal state of hearth. However, some inf...The theoretical flame temperature （TFT） before tuyere, always highly concerned by blast furnace （BF） operators, is one of the most important parameters for evaluating the thermal state of hearth. However, some influ- encing parameters, for example, the SiO2 reduction by carbon, were always neglected or inaccurate when calculating the TFT. According to the definition of TFT, the temperature of coke into raceway and the reduction rate of SiO2 in ash of coke and pulverized coal were obtained by analyzing the samples before tuyere in blast furnace. Taking full ac- count of different factors, a modified model for calculating the TFT in blast furnace was established. The effects of the oxygen enrichment rate, the reduction rate of SiO2 in raceway, the ash content in coke and pulverized coal and the pulverized coal injection （PCI） rate on TFT were determined quantitatively. The modified model was applied to selecting the used coal for PCI in blast furnace. Considering the different SiO2 contents of mixed coal, the calculated TFT remained a stable level. This showed that the selected coal could be suitable for PCI in blast furnace.展开更多
Considering the discontinuous characteristics of sea ice on various scales,a modified discrete element model（DEM） for sea ice dynamics is developed based on the granular material rheology.In this modified DEM,a soft...Considering the discontinuous characteristics of sea ice on various scales,a modified discrete element model（DEM） for sea ice dynamics is developed based on the granular material rheology.In this modified DEM,a soft sea ice particle element is introduced as a self-adjustive particle size function.Each ice particle can be treated as an assembly of ice floes,with its concentration and thickness changing to variable sizes under the conservation of mass.In this model,the contact forces among ice particles are calculated using a viscous-elastic-plastic model,while the maximum shear forces are described with the Mohr-Coulomb friction law.With this modified DEM,the ice flow dynamics is simulated under the drags of wind and current in a channel of various widths.The thicknesses,concentrations and velocities of ice particles are obtained,and then reasonable dynamic process is analyzed.The sea ice dynamic process is also simulated in a vortex wind field.Taking the influence of thermodynamics into account,this modified DEM will be improved in the future work.展开更多
The water entry problem of an asymmetric wedge with roll motion was analyzed by the method of a modified Logvinovich model (MLM). The MLM is a kind of analytical model based on the Wagner method, which linearizes the ...The water entry problem of an asymmetric wedge with roll motion was analyzed by the method of a modified Logvinovich model (MLM). The MLM is a kind of analytical model based on the Wagner method, which linearizes the free surface condition and body boundary condition. The difference is that the MLM applies a nonlinear Bernoulli equation to obtain pressure distribution, which has been proven to be helpful to enhance the accuracy of hydrodynamic loads. The Wagner condition in this paper was generalized to solve the problem of the water entry of a wedge body with rotational velocity. The comparison of wet width between the MLM and a fully nonlinear numerical approach was given, and they agree well with each other. The effect of angular velocity on the hydrodynamic loads of a wedge body was investigated.展开更多
Two modifications for the basic Barcelona model(BBM) are present. One is the replacement of the net stress by the average skeleton stress in unsaturated soil modeling, and the other is the adoption of an expression fo...Two modifications for the basic Barcelona model(BBM) are present. One is the replacement of the net stress by the average skeleton stress in unsaturated soil modeling, and the other is the adoption of an expression for the load-collapse(LC) yield surface that can match flexibly the normal compression lines at different suctions. The predictions of the modified BBM for the controlled-suction triaxial test on the unsaturated compacted clay are presented and compared with the experimental results. A good agreement between the predicted and experimental results demonstrates the reasonability of the modified BBM. On this basis, the coupled processes of groundwater flow and soil deformation in a homogeneous soil slope under a long heavy rainfall are simulated with the proposed elasto-plastic model. The numerical results reveal that the failure of a slope under rainfall infiltration is due to both the reduction of soil suction and the significant rise in groundwater table. The evolution of the displacements is greatly related to the change of suction. The maximum collapse deformation happens near the surface of slope where infiltrated rainwater can quickly reach. The results may provide a helpful reference for hazard assessment and control of rainfall-induced landslides.展开更多
The existing magnetomechancial models cannot explain the different experimental phenomena when the ferromagnetic specimen is respectively subjected to tension and compression stress in the constant and low intensity m...The existing magnetomechancial models cannot explain the different experimental phenomena when the ferromagnetic specimen is respectively subjected to tension and compression stress in the constant and low intensity magnetic field,especially in the compression case. To promote the development of magnetomechancial theory, the energy conservation equation, effective magnetic field equation, and anhysteretic magnetization equation of the original Jiles-Atherton（J-A）theory are elucidated and modified, an equation of the local equilibrium status is employed and the differential expression of the modified magnetomechancial model based on the modified J-A theory is established finally. The effect of stress and plastic deformation on the magnetic parameters is analyzed. An excellent agreement is achieved between the theoretic predictions by the present modified model and the previous experimental results. Comparing with the calculation results given by the existing models and experimental results, it is seen indeed that the modified magnetomechanical model can describe the different magnetization features during tension-release and compression-release processes much better, and is the only one which can accurately reflect the experimental observation that the magnetic induction intensity reverses to negative value with the increase of the compressive stress and applied field.展开更多
The subway is the primary travel tool for urban residents in China. Due to the complex structure of the subway and high personnel density in rush hours, subway evacuation capacity is critical. The subway evacuation mo...The subway is the primary travel tool for urban residents in China. Due to the complex structure of the subway and high personnel density in rush hours, subway evacuation capacity is critical. The subway evacuation model is explored in this work by combining the improved social force model with the view radius using the Vicsek model. The pedestrians are divided into two categories based on different force models. The first category is sensitive pedestrians who have normal responses to emergency signs. The second category is insensitive pedestrians. By simulating different proportions of the insensitive pedestrians, we find that the escape time is directly proportional to the number of insensitive pedestrians and inversely proportional to the view radius. However, when the view radius is large enough, the escape time does not change significantly, and the evacuation of people in a small view radius environment tends to be integrated. With the improvement of view radius conditions, the escape time changes more obviously with the proportion of insensitive pedestrians. A new emergency sign layout is proposed, and the simulations show that the proposed layout can effectively reduce the escape time in a small view radius environment. However, the evacuation effect of the new escape sign layout on the large view radius environment is not apparent. In this case, the exit setting emerges as an additional factor affecting the escape time.展开更多
In this study,through experimental research and an investigation on large datasets of the durability parameters in ocean engineering,the values,ranges,and types of distribution of the durability parameters employed fo...In this study,through experimental research and an investigation on large datasets of the durability parameters in ocean engineering,the values,ranges,and types of distribution of the durability parameters employed for the durability design in ocean engineering in northern China were confirmed.Based on a modified theoretical model of chloride diffusion and the reliability theory,the service lives of concrete structures exposed to the splash,tidal,and underwater zones were calculated.Mixed concrete proportions meeting the requirement of a service life of 100 or 120 years were designed,and a cover thickness requirement was proposed.In addition,the effects of the different time-varying relationships of the boundary condition(Cs)and diffusion coefficient(Df)on the service life were compared;the results showed that the time-varying relationships used in this study(i.e.,Cscontinuously increased and then remained stable,and Dfcontinuously decreased and then remained stable)were beneficial for the durability design of concrete structures in marine environment.展开更多
In order to theoretically study the growth morphology of dihydroxylammonium 5,5’-bistetrazole-1,1’-dio late(TKX-50)crystal in different solvent systems,crystal–solvent models were established,and then molecular dyn...In order to theoretically study the growth morphology of dihydroxylammonium 5,5’-bistetrazole-1,1’-dio late(TKX-50)crystal in different solvent systems,crystal–solvent models were established,and then molecular dynamics(MD)methods were adopted as a means to simulate particle motion.Modified attachment energy(MAE)model was employed to calculate the growth morphology of TKX-50.The simulation results demonstrate that COMPASS force field and RESP charge are suitable for molecular dynamics simulation of TKX-50.The morphologically dominant growth surfaces of TKX-50 in vacuum are(020),(011),(11–1),(100)and(120),respectively.In water(H_(2)O)and N,N-dimethylformamide(DMF)solvents,the(11–1)face is the largest in the habit face,the growth rate of(020)face becomes faster.With the increase of temperature,the aspect ratios of TKX-50 crystal in DMF solvent increase,and the areas of the(120)faces decrease.In ethylene glycol/H_(2)O mixed solvent system with volume ratio of 1/1,aspect ratio of TKX-50 is relatively small.In formic acid/H_(2)O mixed solvents with different volume ratios(1/4,1/3,1/2,1/1 and 2/1),aspect ratio of TKX-50 is relatively small when volume ratio is 1/2.展开更多
The modified sub regular solution model was used for a calculation of the activity coefficient of immiscible binary alloy systems. The parameters needed for the calculation are the interaction parameters, λ 1 a...The modified sub regular solution model was used for a calculation of the activity coefficient of immiscible binary alloy systems. The parameters needed for the calculation are the interaction parameters, λ 1 and λ 2, which are represented as a linear function of temperature, T . The molar excess Gibbs free energy, G m E, can be written in the form G m E= x A x B[( λ 11 + λ 12 T )+( λ 21 + λ 22 T ) x B ] The calculation is carried out numerically for three immiscible binary alloy systems, Al Pb, Cu Tl and In V. The agreement between the calculated and experimentally determined values of activity coefficient is excellent.展开更多
基金supported by the National Natural Science Foundation of China(Nos.41975044,42371354,41801021,42101385)Open Fund of Hubei Luojia Laboratory(No.2201000043)the Fundamental Research Funds for National Universities,China University of Geosciences,Wuhan。
文摘As a crucial human activity,dam construction can profoundly impact the surface hydrology patterns.The Three Gorges Reservoir(TGR),as one of the largest hydraulic engineering projects in the world,has gained continuous attention for its eco-hydrological effects.However,further investigation is necessary to understand the runoff and social impacts of the TGR on the Upper Yangtze River.This study first employed a modified SWAT model to simulate runoff,compared scenarios with and without the TGR,and finally evaluated water supply and demand in the Upper Yangtze River.The results showed a significant increasing trend in the surface water area of the Upper Yangtze River from 2000-2020.The modified SWAT model performs well in simulating the runoff,with Nash-Sutcliffe Efficiency and Percent Bias improved by 0.04-0.30 and 2-31.90,respectively.Scenario simulation results revealed that the TGR reduced seasonal differences in runoff.During the flood season,the runoff volume at the Yichang Station in the scenario with the TGR is lower than in the scenario without the TGR,peaking at 4500 m3/s.Conversely,in the dry season,the runoff volume of the scenario with TGR is higher,with a maximum increase of 1500 m3/s.The region exhibiting the greatest runoff variations is the Yangtze River's main stem in the Three Gorges Reservoir region.Besides,the TGR notably alleviated the water supply-demand imbalance in Chongqing during the winter and spring seasons,with a maximum increase of 0.16 in the supplydemand index.This study can contribute significantly to understanding the natural and social impacts of the TGR from the perspective of hydrological and scenario simulation.
基金financially supported by National Natural Science Foundation of China(Project No.51878156).
文摘To investigate the performance of utilizing the shape memory effect of SMA(Shape Memory Alloy)wire to generate recovery stress,this paper performed single heating recovery stress tests and reciprocating heating-cooling recovery stress tests on SMA wire under varying initial strain conditions.The effects of various strains and different energized heating methods on the recovery stress of SMA wires were explored in the single heating tests.The SMA wire was strained from 2%to 8%initially,and two distinct heating approaches were employed:one using a large current interval for rapid heating and one using a small current interval for slower heating.The experimental outcomes reveal that during a single heating cycle,the temperature-recovery stress relationship of SMA wire exhibits three distinct stages:the martensite phase stage,the transition stage from martensite to austenite phase,and the austenite phase stage.Notably,the choice of heating method does not influence the maximum recovery stress value,and the correlation between initial strain and maximum recovery stress is predominantly linear.Moreover,conducting the reciprocating temperature rise and fall performance test is important to better simulate the scenario in practical engineering where multiple recovery stress in SMA wires for structural repair.In this test,two temperature cycling methods were studied:interval rise and fall,as well as direct rise and fall.In the case of utilizing the interval temperature rise and fall method,it was observed that the recovery stress associated with cooling was significantly higher than that corresponding to heating at the same temperature.Furthermore,the recovery stress was lower upon subsequent heating than that measured during the previous heating cycle.Based on the experimental results,a prediction model for the temperature-recovery stress relationship has been proposed to simplify numerical calculations.It is hoped that an approximate temperaturerecovery stress curve can be obtained from the parameters of the SMA wire.The calculated values derived from this model show good alignment with the measured values,indicating its reliability.
文摘In this paper, we study a modified Leslie-Gower predator-prey model with Smith growth subject to homogeneous Neumann boundary condition, in which the functional response is the Crowley-Martin functional response term. Firstly, for ODE model, the local stability of equilibrium point is given. And by using bifurcation theory and selecting suitable bifurcation parameters, we find many kinds of bifurcation phenomena, including Transcritical bifurcation and Hopf bifurcation. For the reaction-diffusion model, we find that Turing instability occurs. Besides, it is proved that Hopf bifurcation exists in the model. Finally, numerical simulations are presented to verify and illustrate the theoretical results.
基金financially supported by the National Natural Science Foundation of China(Nos.51275415 and50905144)the Natural Science Basic Research Plan in Shanxi Province(No.2011JQ6004)the Program of the Ministry of Education of China for Introducing Talents of Discipline to Universities(No.B08040)
文摘Warm rotary draw bending provides a feasible method to form the large-diameter thin-walled（LDTW）TC4 bent tubes, which are widely used in the pneumatic system of aircrafts. An accurate prediction of flow behavior of TC4 tubes considering the couple effects of temperature,strain rate and strain is critical for understanding the deformation behavior of metals and optimizing the processing parameters in warm rotary draw bending of TC4 tubes. In this study, isothermal compression tests of TC4 tube alloy were performed from 573 to 873 K with an interval of 100 K and strain rates of 0.001, 0.010 and0.100 s^（-1）. The prediction of flow behavior was done using two constitutive models, namely modified Arrhenius model and artificial neural network（ANN） model. The predictions of these constitutive models were compared using statistical measures like correlation coefficient（R）, average absolute relative error（AARE） and its variation with the deformation parameters（temperature, strain rate and strain）. Analysis of statistical measures reveals that the two models show high predicted accuracy in terms of R and AARE. Comparatively speaking, the ANN model presents higher predicted accuracy than the modified Arrhenius model. In addition, the predicted accuracy of ANN model presents high stability at the whole deformation parameter ranges, whereas the predictability of the modified Arrhenius model has some fluctuation at different deformation conditions. It presents higher predicted accuracy at temperatures of 573-773 K, strain rates of 0.010-0.100 s^（-1）and strain of 0.04-0.32, while low accuracy at temperature of 873 K, strain rates of 0.001 s^（-1）and strain of 0.36-0.48.Thus, the application of modified Arrhenius model is limited by its relatively low predicted accuracy at some deformation conditions, while the ANN model presents very high predicted accuracy at all deformation conditions,which can be used to study the compression behavior of TC4 tube at the temperature range of 573-873 K and the strain rate of 0.001-0.100 s^（-1）. It can provide guideline for the design of processing parameters in warm rotary draw bending of LDTW TC4 tubes.
文摘Through modifying the CPN model, a kind of multivariable fuzzy model is put forward, and the matching fuzzy multistep predictive control algorithm is deduced based on the model. The modified model works in a competitive output manner which results in its local representation property. While studying on line, only a few parameters need to be regulated. So the model has the merits of fast learning and on line self organizing modeling. The control algorithm is simple, adaptive and useful in multivariable and time delay systems. Applying the algorithm in a paper making system, simulation shows its good effect.
基金Project(2009ZX04004-031-04) supported by the National Science and Technology Major Project of the Ministry of Science and Technology of China
文摘Compaction process simulation and residual stress prediction of green PM compact were carried out with elasto-plastic 3D FEA based on the modified Drueker-Prager Cap model in Abaqus. The model parameters of the investigated powder Distaloy AE were determined as functions of relative density through typical mechanical property tests of powder. The model was implemented as a user subroutine USDFLD. Single sided compaction of a d20 ram^5 mm disk green compact of Distaloy AE was simulated, and the residual stress of the disk after ejection was predicted with FEA. The FEA results of the compaction process and the residual stress of the disk show good agreement with compaction experiments and X-ray diffraction measurements, which validates the model and its parameters. The results indicate that the compressive residual stresses exist mainly in a thin layer on the side surface, but the residual stresses are very small on the top and bottom surfaces.
基金Project(51675061)supported by the National Natural Science Foundation of China
文摘The hot compressive deformation behaviors of Cu-6wt.%Ag alloy were studied experimentally in the temperature range of 973.1123 K and the strain rate range of 0.01.10 s^-1.The stress increases and reaches the maximum value when the true strain is very small,and then the stress changes slowly and tends to be stable under the action of work hardening,dynamic recovery and recrystallization.The material parameters of the conventional Arrhenius constitutive model are only related to strain under different deformation conditions,and the prediction error is large,which cannot accurately characterize the hot deformation behavior of the alloy.To describe the hot deformation behavior of the alloy accurately,a modified constitutive model was established by considering the simultaneous influence of forming temperature,strain rate and strain.The results indicate that correlation coefficient(R)and the average absolute relative error(AARE)are 0.993 and 4.2%,respectively.The modified constitutive model can accurately describe the hot deformation behavior of Cu-6wt.%Ag alloy.
基金Supported by the National Natural Science Foundation of China(No.29576238).
文摘Taking into account the viscoelasticity of the fenugreek gum, a modified Maxwell model in terms of fractional derivatives is developed. Using this model, it is observed that the fenugreek gums with at least two different concentrations obey the Cox-Merz rule.
基金supported by the National Natural Science Foundation of China (Grants No. 51179075 and 51239005) A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘Considering the compressibility of the cavity in the cavitating flow, this paper presents a modified k-ω model for predicting the cavitating flow in a centrifugal pump, in which the modified k-ω model and Schnerr-Sauer cavitation model were combined with ANSYS CFX. To evaluate the modified and standard k-co models, numerical simulations were performed with these two models, respectively, and the calculation results were compared with the experimental data. Numerical simulations were executed with three different values of the flow coefficient, and the simulation results of the modified k-ω model showed agreement with most of the experimental data. The cavitating flow in the centrifugal pump obtained by the modified k-ω model at the design flow coefficient of 0.102, was analyzed. When the cavitation number decreases, the cavity initially generates on the suction side of the blade near the leading edge and then expands to the outlet of the impeller, and the decrease of the total pressure coefficient mainly occurs upstream of the impeller passage, while the downstream remains almost unaffected by the development of cavitation.
文摘AIM:To explore the related risk factors for diabetic retinopathy(DR)in type 2 diabetes with insulin therapy.METHODS:We studied the relationships among blood glucose,serum C-peptide,plasma insulin,beta-cell function and the development of DR.Beta-cell function was assessed by a modified homeostasis model assessment(modified HOMA)which was gained by using C-peptide to replace insulin in the homeostasis model assessment(HOMA)of beta-cell function.We also studied the relationships between modified HOMA index and serum C-peptide response to 100 g tasteless steamed bread to determine the accuracy of modified HOMA.RESULTS:Our study group consisted of 170 type 2diabetic inpatients with DR(age:58.35±13.87y,mean±SD)and 205 type 2 diabetic inpatients with no DR(NDR)(age:65.52±11.59y).DR patients had higher age,longer diabetic duration,higher hypertension grade,higher postprandial plasma glucose,higher fluctuation level of plasma glucose,lower body mass index(BMI),lower postprandial serum insulin and C-peptide,lower fluctuation level of serum insulin and C-peptide(P【0.05).In our logistic regression model,duration of diabetes,hypertension grade,fasting plasma insulin and glycosylated hemoglobin(HbA1C)were significantly associated with the presence of DR after adjustment for confounding factors(P【0.05).CONCLUSION:Our results suggested although modified HOMA showed significant correlation to the occurrence of DR on Spearman’s rank-correlationanalysis,logistic regression showed no significant association between these two variables after adjustment for relevant confounding factors(such as age,sex,duration of diabetes,BMI,hypertension grade,HbA1C,plasma insulin).Duration of diabetes,hypertension grade,fasting plasma insulin and HbA1C were independently associated with the development of DR in Chinese type 2 diabetics.
文摘The purpose of this study is to predict the morphologies in the solidification process for Cu-0.6Cr(mass fraction,%)alloy by vacuum continuous casting(VCC)and verify its accuracy by the observed experimental results.In numerical simulation aspect, finite difference(FD)method and modified cellular automaton(MCA)model were used to simulate the macro-temperature field, micro-concentration field,nucleation and grain growth of Cu-0.6Cr alloy using real data from actual casting operations.From the observed casting experiment,the preliminary grain morphologies are the directional columnar grains by the VCC process.The solidification morphologies by MCAFD model are in agreement with the result of actual casting experiment well.
基金Sponsored by National Natural Science Foundation of China and Baosteel(51274026,50874129)National High-tech Research and Development Program of China(2009AA06Z105)
文摘The theoretical flame temperature （TFT） before tuyere, always highly concerned by blast furnace （BF） operators, is one of the most important parameters for evaluating the thermal state of hearth. However, some influ- encing parameters, for example, the SiO2 reduction by carbon, were always neglected or inaccurate when calculating the TFT. According to the definition of TFT, the temperature of coke into raceway and the reduction rate of SiO2 in ash of coke and pulverized coal were obtained by analyzing the samples before tuyere in blast furnace. Taking full ac- count of different factors, a modified model for calculating the TFT in blast furnace was established. The effects of the oxygen enrichment rate, the reduction rate of SiO2 in raceway, the ash content in coke and pulverized coal and the pulverized coal injection （PCI） rate on TFT were determined quantitatively. The modified model was applied to selecting the used coal for PCI in blast furnace. Considering the different SiO2 contents of mixed coal, the calculated TFT remained a stable level. This showed that the selected coal could be suitable for PCI in blast furnace.
基金Special Fund of Marine Commonweal Industry under contact Nos 201105016 and 201205007supported by National Marine Environment Forecasting Centrethe National Natural Science Foundation of China under contact No.41176012
文摘Considering the discontinuous characteristics of sea ice on various scales,a modified discrete element model（DEM） for sea ice dynamics is developed based on the granular material rheology.In this modified DEM,a soft sea ice particle element is introduced as a self-adjustive particle size function.Each ice particle can be treated as an assembly of ice floes,with its concentration and thickness changing to variable sizes under the conservation of mass.In this model,the contact forces among ice particles are calculated using a viscous-elastic-plastic model,while the maximum shear forces are described with the Mohr-Coulomb friction law.With this modified DEM,the ice flow dynamics is simulated under the drags of wind and current in a channel of various widths.The thicknesses,concentrations and velocities of ice particles are obtained,and then reasonable dynamic process is analyzed.The sea ice dynamic process is also simulated in a vortex wind field.Taking the influence of thermodynamics into account,this modified DEM will be improved in the future work.
基金Supported by Supported by "111 Program" (B07019)
文摘The water entry problem of an asymmetric wedge with roll motion was analyzed by the method of a modified Logvinovich model (MLM). The MLM is a kind of analytical model based on the Wagner method, which linearizes the free surface condition and body boundary condition. The difference is that the MLM applies a nonlinear Bernoulli equation to obtain pressure distribution, which has been proven to be helpful to enhance the accuracy of hydrodynamic loads. The Wagner condition in this paper was generalized to solve the problem of the water entry of a wedge body with rotational velocity. The comparison of wet width between the MLM and a fully nonlinear numerical approach was given, and they agree well with each other. The effect of angular velocity on the hydrodynamic loads of a wedge body was investigated.
基金Project(1301015A)supported by the Post-doctoral Research Fund of Jiangsu Province,ChinaProject Funded by the Priority Academic Program of Jiangsu Higher Education Institution,China+1 种基金Project(2014M561566)supported by China Postdoctoral Science FoundationProject(YK913007)supported by Key Laboratory of Earth-Rock Dam Failure Mechanism and Safety Control Technologies,China
文摘Two modifications for the basic Barcelona model(BBM) are present. One is the replacement of the net stress by the average skeleton stress in unsaturated soil modeling, and the other is the adoption of an expression for the load-collapse(LC) yield surface that can match flexibly the normal compression lines at different suctions. The predictions of the modified BBM for the controlled-suction triaxial test on the unsaturated compacted clay are presented and compared with the experimental results. A good agreement between the predicted and experimental results demonstrates the reasonability of the modified BBM. On this basis, the coupled processes of groundwater flow and soil deformation in a homogeneous soil slope under a long heavy rainfall are simulated with the proposed elasto-plastic model. The numerical results reveal that the failure of a slope under rainfall infiltration is due to both the reduction of soil suction and the significant rise in groundwater table. The evolution of the displacements is greatly related to the change of suction. The maximum collapse deformation happens near the surface of slope where infiltrated rainwater can quickly reach. The results may provide a helpful reference for hazard assessment and control of rainfall-induced landslides.
基金Project supported by the Major Program of Sichuan Province Science and Technology Plan,China(Grant No.2015SZ0010)the Scientific Research Foundation of Sichuan Province,China(Grant No.2014GZ0121)
文摘The existing magnetomechancial models cannot explain the different experimental phenomena when the ferromagnetic specimen is respectively subjected to tension and compression stress in the constant and low intensity magnetic field,especially in the compression case. To promote the development of magnetomechancial theory, the energy conservation equation, effective magnetic field equation, and anhysteretic magnetization equation of the original Jiles-Atherton（J-A）theory are elucidated and modified, an equation of the local equilibrium status is employed and the differential expression of the modified magnetomechancial model based on the modified J-A theory is established finally. The effect of stress and plastic deformation on the magnetic parameters is analyzed. An excellent agreement is achieved between the theoretic predictions by the present modified model and the previous experimental results. Comparing with the calculation results given by the existing models and experimental results, it is seen indeed that the modified magnetomechanical model can describe the different magnetization features during tension-release and compression-release processes much better, and is the only one which can accurately reflect the experimental observation that the magnetic induction intensity reverses to negative value with the increase of the compressive stress and applied field.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51874183 and 51874182)the National Key Research and Development Program of China (Grant No. 2018YFC0809300)。
文摘The subway is the primary travel tool for urban residents in China. Due to the complex structure of the subway and high personnel density in rush hours, subway evacuation capacity is critical. The subway evacuation model is explored in this work by combining the improved social force model with the view radius using the Vicsek model. The pedestrians are divided into two categories based on different force models. The first category is sensitive pedestrians who have normal responses to emergency signs. The second category is insensitive pedestrians. By simulating different proportions of the insensitive pedestrians, we find that the escape time is directly proportional to the number of insensitive pedestrians and inversely proportional to the view radius. However, when the view radius is large enough, the escape time does not change significantly, and the evacuation of people in a small view radius environment tends to be integrated. With the improvement of view radius conditions, the escape time changes more obviously with the proportion of insensitive pedestrians. A new emergency sign layout is proposed, and the simulations show that the proposed layout can effectively reduce the escape time in a small view radius environment. However, the evacuation effect of the new escape sign layout on the large view radius environment is not apparent. In this case, the exit setting emerges as an additional factor affecting the escape time.
基金financial support provided by the National Natural Science Foundation of China(51508272,11832013,51878350,and 51678304)。
文摘In this study,through experimental research and an investigation on large datasets of the durability parameters in ocean engineering,the values,ranges,and types of distribution of the durability parameters employed for the durability design in ocean engineering in northern China were confirmed.Based on a modified theoretical model of chloride diffusion and the reliability theory,the service lives of concrete structures exposed to the splash,tidal,and underwater zones were calculated.Mixed concrete proportions meeting the requirement of a service life of 100 or 120 years were designed,and a cover thickness requirement was proposed.In addition,the effects of the different time-varying relationships of the boundary condition(Cs)and diffusion coefficient(Df)on the service life were compared;the results showed that the time-varying relationships used in this study(i.e.,Cscontinuously increased and then remained stable,and Dfcontinuously decreased and then remained stable)were beneficial for the durability design of concrete structures in marine environment.
基金supported by Fundamental Research Program of Shanxi Province(20210302123055)and(201801D221035).
文摘In order to theoretically study the growth morphology of dihydroxylammonium 5,5’-bistetrazole-1,1’-dio late(TKX-50)crystal in different solvent systems,crystal–solvent models were established,and then molecular dynamics(MD)methods were adopted as a means to simulate particle motion.Modified attachment energy(MAE)model was employed to calculate the growth morphology of TKX-50.The simulation results demonstrate that COMPASS force field and RESP charge are suitable for molecular dynamics simulation of TKX-50.The morphologically dominant growth surfaces of TKX-50 in vacuum are(020),(011),(11–1),(100)and(120),respectively.In water(H_(2)O)and N,N-dimethylformamide(DMF)solvents,the(11–1)face is the largest in the habit face,the growth rate of(020)face becomes faster.With the increase of temperature,the aspect ratios of TKX-50 crystal in DMF solvent increase,and the areas of the(120)faces decrease.In ethylene glycol/H_(2)O mixed solvent system with volume ratio of 1/1,aspect ratio of TKX-50 is relatively small.In formic acid/H_(2)O mixed solvents with different volume ratios(1/4,1/3,1/2,1/1 and 2/1),aspect ratio of TKX-50 is relatively small when volume ratio is 1/2.
文摘The modified sub regular solution model was used for a calculation of the activity coefficient of immiscible binary alloy systems. The parameters needed for the calculation are the interaction parameters, λ 1 and λ 2, which are represented as a linear function of temperature, T . The molar excess Gibbs free energy, G m E, can be written in the form G m E= x A x B[( λ 11 + λ 12 T )+( λ 21 + λ 22 T ) x B ] The calculation is carried out numerically for three immiscible binary alloy systems, Al Pb, Cu Tl and In V. The agreement between the calculated and experimentally determined values of activity coefficient is excellent.
