There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cab...There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cable simultaneously, a double differential-mode current in- jection test method (DDMCI) is proposed. The method adopted the equivalence source wave theorem and Baum-Liu-Tesche(BLT) equation as its theory foundation. The equivalent corresponding relation between injection voltage and radiation electric field intensity is derived, and the phase relation between the two injection voltage sources is confirmed. The results indicate that the amplitude and phase of the equivalent injection voltage source is closely related to the S parameter of directional coupling device, the transmission line length, and the source vector in BLT equation, but has nothing to do with the reflection coefficient between the two equipment pieces. Therefore, by choosing the right amplitude and phase of the double injection voltage sources, the DDMCI test is equivalent to the radiation test for two interconnected equipment of a system.展开更多
To achieve the electric field strength and the induced currents in equivalence in susceptibility tests with the high-level field radiation above 400 MHz,a double differential-mode(DM) current injection method based on...To achieve the electric field strength and the induced currents in equivalence in susceptibility tests with the high-level field radiation above 400 MHz,a double differential-mode(DM) current injection method based on directional couplers is proposed.Two cascaded symmetrical directional couplers compose a coupling device to inject the DM currents.When the coupling device is used,two devices are necessary to achieve the equivalence between radiation and injection,i.e.the equivalence between the injected voltages and the field strength,which is linear,regardless of the characteristics of the equipment under test(EUT).The results are verified by experiments using typical coaxial cables and nonlinear devices,where the equivalence between the nonlinear EUT responses induced by radiation and injection at both ends is achieved by using two coupling devices.At a frequency up to 1.75 GHz,the maximal experimental error is only 3.39%.The experimental results confirm the accuracy of the proposed method even both the EUTs work in the nonlinear region.The proposed method is applicable for radiated susceptibility(RS) testing of interconnected systems in the microwave frequency band.展开更多
A novel CMOS bandgap reference is presented. The output reference of this new current mode structure can be set to an arbitrary value above the bandgap voltage of silicon,avoiding offset in application. It also overco...A novel CMOS bandgap reference is presented. The output reference of this new current mode structure can be set to an arbitrary value above the bandgap voltage of silicon,avoiding offset in application. It also overcomes the systematic mismatch of conventional current mode bandgap references. The proposed bandgap reference has been implemented in UMC 0.18μm mixed mode technology. Under the supply voltage of 1.6V, the proposed bandgap reference provides an output reference of 1.45V and consumes 27μA of supply current. Using no curvature compensation,it can reach a temperature coefficient of 23ppm/℃ from 30 to 150℃ with a line regulation of 2. 1mV/V from 1.6 to 3V and a PSRR of 40dB at DC frequency. The chip area of the bandgap reference （without pad） is 0. 088mm^2.展开更多
A single power supply common-gate （CG） current mode transimpedance preamplifier （TIA） is developed with a 0.5μm GaAs PHEMT process. The amplifier has a measured - 3dB bandwidth of 7. 5GHz and a transimpedance gai...A single power supply common-gate （CG） current mode transimpedance preamplifier （TIA） is developed with a 0.5μm GaAs PHEMT process. The amplifier has a measured - 3dB bandwidth of 7. 5GHz and a transimpedance gain of 45dBΩ. Both the input and output voltage standing wave ratios （VSWR） are less than 2 within the bandwidth. The equivalent input noise current spectral density varies from 14.3 to 22pA/√Hz, with an average value of 17. 2pA/√Hz. Having a timing jitter of 14ps and eye amplitude of about 138mV,the measured output eye diagram for 10Gb/s NRZ pseudorandom binary sequence （PRBS） is clear and satisfactory.展开更多
A practical method of current mode circuit symbolic analysis using Mathematica is proposed. With the powerful symbolic manipulation capacity of Mathematica, current mode circuit symbolic analysis can be significantly ...A practical method of current mode circuit symbolic analysis using Mathematica is proposed. With the powerful symbolic manipulation capacity of Mathematica, current mode circuit symbolic analysis can be significantly simplified. The active devices are modelled by nullors. The examples of current mode filters using CCIIs are presented.展开更多
An improved high-resolution current-mode sorter is presented.Its structure complexity is O(N),which is crucial to the expansion of its size,and its dynamic range is large.Only one clock signal and one reset signal are...An improved high-resolution current-mode sorter is presented.Its structure complexity is O(N),which is crucial to the expansion of its size,and its dynamic range is large.Only one clock signal and one reset signal are needed.No biasing signal is required.The operation point is constructed according to the input current,so it is self-adaptive,which is very important for an all-purpose component.In average value circuit,subtraction circuit,Winner-Take-All(WTA) circuit and control circuit,it has good performance even at a large input current.This sorter has high precision,high resolution and low power,as has been proved via HSPICE simulation.It can be implemented in the standard digital CMOS technology and widely used in many fields,so it is of great value in applications.展开更多
Carbon Nano-Tube Field Effect Transistors(CNTFETs) are being widely studied as possible successors to silicon MOSFETs.Using current mode has many advantages such as performing sum operation by means of a simple wired ...Carbon Nano-Tube Field Effect Transistors(CNTFETs) are being widely studied as possible successors to silicon MOSFETs.Using current mode has many advantages such as performing sum operation by means of a simple wired connection.Also,direction of the current can be used to exhibit the sign of digits.It is expected that the advantages of current mode approaches will become even more important with increased speed requirements and decreased supply voltage.In this paper,we present five new circuit designs for differential absolute value in current mode logic which have been simulated by CNTFET model.The considered base current for this model is 2 μA and supply voltage is 0.9 V.In all of our designs we used N-type CNTFET current mirrors which operate as truncated difference circuits.The operation of Differential Absolute Value circuit calculates the difference between two input currents and our circuit designs are operate in 8 logic levels.展开更多
A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magne...A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.展开更多
Based on a linearized MHD model, the effect of equilibrium current profiles on external kink modes in tokamaks is studied by MARS code. Three types of equilibrium current profiles are adopted in this work. Firstly, a ...Based on a linearized MHD model, the effect of equilibrium current profiles on external kink modes in tokamaks is studied by MARS code. Three types of equilibrium current profiles are adopted in this work. Firstly, a set of parabolic equilibrium current profiles are chosen. In these profiles the maximum current values in the center of the plasma are fixed, and the currents have different gradient and jump at the plasma boundary. The effects of the current gradient and jump on the growth rate of external kink mode are investigated. It is found that the current jump which causes the q profiles to change plays an important role in the externM kink modes in tokamaks. Secondly, a set of step equilibrium current profiles with different jump positions are chosen. The effect of jump position on external kink modes is discussed. Thirdly, a set of parabolic equilibrium current profiles with current bumps are chosen for the case of off-axis heating. The effects of height~ width and position of the current bumps on external kink modes are analyzed. The fiat equilibrium current profiles are disadvantageous for the MHD stabilities of tokamaks, because of the large current jump at the plasma edge. The peaked equilibrium current profiles and a large and localized current bump near the plasma edge benefit the MHD stabilities of tokamaks.展开更多
One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltag...One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltage-mode circuit exhibit simultaneously lowpass and bandpass filters. The proposed current-mode circuit exhibit simultaneously lowpass, bandpass and highpass filters. The proposed circuits offer the following features: no requirements for component matching conditions;low active and passive sensitivities;employing only grounded capacitors and the ability to obtain multifunction filters from the same circuit configuration.展开更多
This paper presents a synthesis of current-mode PI, PD and PID controllers employing current controlled current differential buffer amplifiers (CCCDBAs). The features of these controllers are that: the output paramete...This paper presents a synthesis of current-mode PI, PD and PID controllers employing current controlled current differential buffer amplifiers (CCCDBAs). The features of these controllers are that: the output parameters can be electronically/independently controlled by adjusting corresponding bias currents in the proportional, integral, and deviation controllers;circuit description of the PID controller is simply formulated, it consists of four CCCDBAs cooperating with two grounded capacitors, and PI and PD controllers are composed of three CCCCDBAs and a grounded capacitor. Without any external resistor, the proposed circuits are very suitable to develop into integrated circuit architecture. The given results from the PSpice simulation agree well with the theoretical anticipation. The approximate power consumption in a closed loop control system consisting of the PI, PD and PID controller with low-pass filter passive plant are 4.03 mW, 4.85 mW and 5.71 mW, respectively, at ±1.5 V power supply voltages.展开更多
By applying switch-signal theory, the interaction between MOS transmission switch-ing transistor and current signal in current-mode CMOS circuits is analyzed, and the theory oftransmission current-switches which is su...By applying switch-signal theory, the interaction between MOS transmission switch-ing transistor and current signal in current-mode CMOS circuits is analyzed, and the theory oftransmission current-switches which is suitable to current-mode CMOS circuits is proposed. Thecircuits, such as ternary full-adder etc., designed by using this theory have simpler circuit struc-tures and correct logic functions. It is confirmed that this theory is efficient in guiding the logicdesign of current-mode CMOS circuits at switch level.展开更多
Based on the analysis of the basic principle of slope compensation, a high-precision adaptive slope compensation circuit for peak current mode boost DC/DC converter is designed. The circuit dynamically detects the inp...Based on the analysis of the basic principle of slope compensation, a high-precision adaptive slope compensation circuit for peak current mode boost DC/DC converter is designed. The circuit dynamically detects the input and output voltage of the boost circuit to realize automatic adjustment of the compensation amount with the change of duty ratio, which makes the ramp compensation slope optimized. The design uses a high-precision subtracter to improve the accuracy of slope compensation. While eliminating sub-slope oscillation and improving the stability of boost circuit, the negative impact of compensation on boost circuit is minimized, and the load capacity and transient response speed of boost circuit are guaranteed. The circuit is designed based on SMIC 0.18um CMOS technology, with simple structure, high reliability and easy engineering implementation. Spectre circuit simulator 17.1.0.124 64b simulation results show that the circuit has high compensation accuracy and wide input and output voltage range. When the working voltage is 3.3 V, the compensation slope can be adjusted adaptively under different duty cycles, and the minimum error between the compensation slope and the theoretical optimal compensation slope is only 0.42%.展开更多
A state variable method of converting single-resistance-controlled- oscillators (SRCO), into universal current-mode biquad (offering realizations of all the five standard filter functions namely, low pass, band pass, ...A state variable method of converting single-resistance-controlled- oscillators (SRCO), into universal current-mode biquad (offering realizations of all the five standard filter functions namely, low pass, band pass, high pass, notch and all pass) has been highlighted. The workability of the exemplary implementation of the derived current-mode universal biquad has been demonstrated by PSPICE simulation results based upon 0.35 μ m technology. It is expected that the proposed method can be applied to other SRCOs to generate other multifunction filter structures.展开更多
This paper presents a new current-mode single input multi output (SIMO) type biquad employing one voltage differencing transconductance amplifier (VDTA), two grounded capacitors and a single grounded resistor. The con...This paper presents a new current-mode single input multi output (SIMO) type biquad employing one voltage differencing transconductance amplifier (VDTA), two grounded capacitors and a single grounded resistor. The configuration realizes all basic filter functions (i.e. Low Pass (LP), High Pass (HP), Band Pass (BP), Notch (BR) and All Pass (AP)). The natural frequency (ω0) and bandwidth (BW) are independently tunable. The workability of proposed configuration has been verified using SPICE simulation with TSMC CMOS 0.18 μm process parameters.展开更多
An electronically controllable fully uncoupled explicit current-mode quadrature oscillator employing Voltage Differencing Transconductance Amplifiers (VDTAs) as active elements has been presented. The proposed configu...An electronically controllable fully uncoupled explicit current-mode quadrature oscillator employing Voltage Differencing Transconductance Amplifiers (VDTAs) as active elements has been presented. The proposed configuration employs two VDTAs along with grounded capacitors and offers the following advantageous features 1) fully and electronically independent control of condition of oscillation (CO) and frequency of oscillation (FO);2) explicit current-mode quadrature oscillations;and 3) low active and passive sensitivities. The workability of proposed configuration has been demonstrated by PSPICE simulations with TSMC CMOS 0.18 μm process parameters.展开更多
This paper presents an electronically tunable current/trans-impedance-mode biquad universal filter employing only single multi-output current controlled current conveyor trans-conductance amplifier (MO-CCCCTA) and two...This paper presents an electronically tunable current/trans-impedance-mode biquad universal filter employing only single multi-output current controlled current conveyor trans-conductance amplifier (MO-CCCCTA) and two grounded capacitors. The proposed filter realizes all the standard filter func-tions i.e. low pass (LP), band pass (BP) and high pass (HP), notch and all pass (AP) filters in the current form at high impedance output through appropriate selection of the input signals, without any matching conditions. Simultaneously, it can also realize all the standard filter functions in trans-impedance form from the same circuit topology. The circuit does not require inverting-type input current signal(s) and double input current signal(s) to realize all the responses in the design. The validity of proposed filter is verified through PSPICE simulations.展开更多
An analytic closed-form based loop compensator for direct current-direct current （DC-DC） buckboost converter in discontinuous conduction with peak current-mode control is proposed to increase efficiency of the desir...An analytic closed-form based loop compensator for direct current-direct current （DC-DC） buckboost converter in discontinuous conduction with peak current-mode control is proposed to increase efficiency of the desired process through systemization. As a result, the process saves a lot of computation time that can be translated into design cost savings. Finally, the output voltage regulation in the presence of audio susceptibility and output impedance is shown for verifying.展开更多
A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of...A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of an oxidation- confined 850 nm VCSEL. The single-mode output power of 2.6 mW, threshold current of 0.6 mA, full width of half maximum lasing spectrum of less than 0.1 nm, side mode suppression ratio of 28.4 dB, and far-field divergence angle of about 10% are obtained. The effects of different hole depths on the optical characteristics are simulated and analysed, including far-field divergence, spectrum and lateral cavity mode. The single-mode performance of this multi-hole device is attributed to the large radiation loss from the inter hole spacing and the scattering loss at the bottom of the holes, particularly for higher order modes.展开更多
基金Project supported by Arm Pre-research Program （51333040101）, National Defense 973 Program （6131380301 ）, National Natural Science Foundation of China （61040003）.
文摘There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cable simultaneously, a double differential-mode current in- jection test method (DDMCI) is proposed. The method adopted the equivalence source wave theorem and Baum-Liu-Tesche(BLT) equation as its theory foundation. The equivalent corresponding relation between injection voltage and radiation electric field intensity is derived, and the phase relation between the two injection voltage sources is confirmed. The results indicate that the amplitude and phase of the equivalent injection voltage source is closely related to the S parameter of directional coupling device, the transmission line length, and the source vector in BLT equation, but has nothing to do with the reflection coefficient between the two equipment pieces. Therefore, by choosing the right amplitude and phase of the double injection voltage sources, the DDMCI test is equivalent to the radiation test for two interconnected equipment of a system.
基金supported by National Basic Research Program of China(973 Program)
文摘To achieve the electric field strength and the induced currents in equivalence in susceptibility tests with the high-level field radiation above 400 MHz,a double differential-mode(DM) current injection method based on directional couplers is proposed.Two cascaded symmetrical directional couplers compose a coupling device to inject the DM currents.When the coupling device is used,two devices are necessary to achieve the equivalence between radiation and injection,i.e.the equivalence between the injected voltages and the field strength,which is linear,regardless of the characteristics of the equipment under test(EUT).The results are verified by experiments using typical coaxial cables and nonlinear devices,where the equivalence between the nonlinear EUT responses induced by radiation and injection at both ends is achieved by using two coupling devices.At a frequency up to 1.75 GHz,the maximal experimental error is only 3.39%.The experimental results confirm the accuracy of the proposed method even both the EUTs work in the nonlinear region.The proposed method is applicable for radiated susceptibility(RS) testing of interconnected systems in the microwave frequency band.
文摘A novel CMOS bandgap reference is presented. The output reference of this new current mode structure can be set to an arbitrary value above the bandgap voltage of silicon,avoiding offset in application. It also overcomes the systematic mismatch of conventional current mode bandgap references. The proposed bandgap reference has been implemented in UMC 0.18μm mixed mode technology. Under the supply voltage of 1.6V, the proposed bandgap reference provides an output reference of 1.45V and consumes 27μA of supply current. Using no curvature compensation,it can reach a temperature coefficient of 23ppm/℃ from 30 to 150℃ with a line regulation of 2. 1mV/V from 1.6 to 3V and a PSRR of 40dB at DC frequency. The chip area of the bandgap reference （without pad） is 0. 088mm^2.
文摘A single power supply common-gate （CG） current mode transimpedance preamplifier （TIA） is developed with a 0.5μm GaAs PHEMT process. The amplifier has a measured - 3dB bandwidth of 7. 5GHz and a transimpedance gain of 45dBΩ. Both the input and output voltage standing wave ratios （VSWR） are less than 2 within the bandwidth. The equivalent input noise current spectral density varies from 14.3 to 22pA/√Hz, with an average value of 17. 2pA/√Hz. Having a timing jitter of 14ps and eye amplitude of about 138mV,the measured output eye diagram for 10Gb/s NRZ pseudorandom binary sequence （PRBS） is clear and satisfactory.
文摘A practical method of current mode circuit symbolic analysis using Mathematica is proposed. With the powerful symbolic manipulation capacity of Mathematica, current mode circuit symbolic analysis can be significantly simplified. The active devices are modelled by nullors. The examples of current mode filters using CCIIs are presented.
文摘An improved high-resolution current-mode sorter is presented.Its structure complexity is O(N),which is crucial to the expansion of its size,and its dynamic range is large.Only one clock signal and one reset signal are needed.No biasing signal is required.The operation point is constructed according to the input current,so it is self-adaptive,which is very important for an all-purpose component.In average value circuit,subtraction circuit,Winner-Take-All(WTA) circuit and control circuit,it has good performance even at a large input current.This sorter has high precision,high resolution and low power,as has been proved via HSPICE simulation.It can be implemented in the standard digital CMOS technology and widely used in many fields,so it is of great value in applications.
文摘Carbon Nano-Tube Field Effect Transistors(CNTFETs) are being widely studied as possible successors to silicon MOSFETs.Using current mode has many advantages such as performing sum operation by means of a simple wired connection.Also,direction of the current can be used to exhibit the sign of digits.It is expected that the advantages of current mode approaches will become even more important with increased speed requirements and decreased supply voltage.In this paper,we present five new circuit designs for differential absolute value in current mode logic which have been simulated by CNTFET model.The considered base current for this model is 2 μA and supply voltage is 0.9 V.In all of our designs we used N-type CNTFET current mirrors which operate as truncated difference circuits.The operation of Differential Absolute Value circuit calculates the difference between two input currents and our circuit designs are operate in 8 logic levels.
基金supported by ITER Program of China(973 Program)(No.2011GB109002)National Natural Science Foundation of China(No.11275056)Hefei University of Technology Doctor Research Foundation of China(No.2011HGBZ1292)
文摘A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.
基金supported by National Natural Science Foundation of China(Nos.11275041 and 11105065)
文摘Based on a linearized MHD model, the effect of equilibrium current profiles on external kink modes in tokamaks is studied by MARS code. Three types of equilibrium current profiles are adopted in this work. Firstly, a set of parabolic equilibrium current profiles are chosen. In these profiles the maximum current values in the center of the plasma are fixed, and the currents have different gradient and jump at the plasma boundary. The effects of the current gradient and jump on the growth rate of external kink mode are investigated. It is found that the current jump which causes the q profiles to change plays an important role in the externM kink modes in tokamaks. Secondly, a set of step equilibrium current profiles with different jump positions are chosen. The effect of jump position on external kink modes is discussed. Thirdly, a set of parabolic equilibrium current profiles with current bumps are chosen for the case of off-axis heating. The effects of height~ width and position of the current bumps on external kink modes are analyzed. The fiat equilibrium current profiles are disadvantageous for the MHD stabilities of tokamaks, because of the large current jump at the plasma edge. The peaked equilibrium current profiles and a large and localized current bump near the plasma edge benefit the MHD stabilities of tokamaks.
文摘One configuration for realizing voltage-mode multifunction filters and another configuration for realizing current-mode multifunction filters using current feedback amplifiers (CFAs) are presented. The proposed voltage-mode circuit exhibit simultaneously lowpass and bandpass filters. The proposed current-mode circuit exhibit simultaneously lowpass, bandpass and highpass filters. The proposed circuits offer the following features: no requirements for component matching conditions;low active and passive sensitivities;employing only grounded capacitors and the ability to obtain multifunction filters from the same circuit configuration.
文摘This paper presents a synthesis of current-mode PI, PD and PID controllers employing current controlled current differential buffer amplifiers (CCCDBAs). The features of these controllers are that: the output parameters can be electronically/independently controlled by adjusting corresponding bias currents in the proportional, integral, and deviation controllers;circuit description of the PID controller is simply formulated, it consists of four CCCDBAs cooperating with two grounded capacitors, and PI and PD controllers are composed of three CCCCDBAs and a grounded capacitor. Without any external resistor, the proposed circuits are very suitable to develop into integrated circuit architecture. The given results from the PSpice simulation agree well with the theoretical anticipation. The approximate power consumption in a closed loop control system consisting of the PI, PD and PID controller with low-pass filter passive plant are 4.03 mW, 4.85 mW and 5.71 mW, respectively, at ±1.5 V power supply voltages.
基金Supported by National Natural Science Foundation of China
文摘By applying switch-signal theory, the interaction between MOS transmission switch-ing transistor and current signal in current-mode CMOS circuits is analyzed, and the theory oftransmission current-switches which is suitable to current-mode CMOS circuits is proposed. Thecircuits, such as ternary full-adder etc., designed by using this theory have simpler circuit struc-tures and correct logic functions. It is confirmed that this theory is efficient in guiding the logicdesign of current-mode CMOS circuits at switch level.
文摘Based on the analysis of the basic principle of slope compensation, a high-precision adaptive slope compensation circuit for peak current mode boost DC/DC converter is designed. The circuit dynamically detects the input and output voltage of the boost circuit to realize automatic adjustment of the compensation amount with the change of duty ratio, which makes the ramp compensation slope optimized. The design uses a high-precision subtracter to improve the accuracy of slope compensation. While eliminating sub-slope oscillation and improving the stability of boost circuit, the negative impact of compensation on boost circuit is minimized, and the load capacity and transient response speed of boost circuit are guaranteed. The circuit is designed based on SMIC 0.18um CMOS technology, with simple structure, high reliability and easy engineering implementation. Spectre circuit simulator 17.1.0.124 64b simulation results show that the circuit has high compensation accuracy and wide input and output voltage range. When the working voltage is 3.3 V, the compensation slope can be adjusted adaptively under different duty cycles, and the minimum error between the compensation slope and the theoretical optimal compensation slope is only 0.42%.
文摘A state variable method of converting single-resistance-controlled- oscillators (SRCO), into universal current-mode biquad (offering realizations of all the five standard filter functions namely, low pass, band pass, high pass, notch and all pass) has been highlighted. The workability of the exemplary implementation of the derived current-mode universal biquad has been demonstrated by PSPICE simulation results based upon 0.35 μ m technology. It is expected that the proposed method can be applied to other SRCOs to generate other multifunction filter structures.
文摘This paper presents a new current-mode single input multi output (SIMO) type biquad employing one voltage differencing transconductance amplifier (VDTA), two grounded capacitors and a single grounded resistor. The configuration realizes all basic filter functions (i.e. Low Pass (LP), High Pass (HP), Band Pass (BP), Notch (BR) and All Pass (AP)). The natural frequency (ω0) and bandwidth (BW) are independently tunable. The workability of proposed configuration has been verified using SPICE simulation with TSMC CMOS 0.18 μm process parameters.
文摘An electronically controllable fully uncoupled explicit current-mode quadrature oscillator employing Voltage Differencing Transconductance Amplifiers (VDTAs) as active elements has been presented. The proposed configuration employs two VDTAs along with grounded capacitors and offers the following advantageous features 1) fully and electronically independent control of condition of oscillation (CO) and frequency of oscillation (FO);2) explicit current-mode quadrature oscillations;and 3) low active and passive sensitivities. The workability of proposed configuration has been demonstrated by PSPICE simulations with TSMC CMOS 0.18 μm process parameters.
文摘This paper presents an electronically tunable current/trans-impedance-mode biquad universal filter employing only single multi-output current controlled current conveyor trans-conductance amplifier (MO-CCCCTA) and two grounded capacitors. The proposed filter realizes all the standard filter func-tions i.e. low pass (LP), band pass (BP) and high pass (HP), notch and all pass (AP) filters in the current form at high impedance output through appropriate selection of the input signals, without any matching conditions. Simultaneously, it can also realize all the standard filter functions in trans-impedance form from the same circuit topology. The circuit does not require inverting-type input current signal(s) and double input current signal(s) to realize all the responses in the design. The validity of proposed filter is verified through PSPICE simulations.
文摘An analytic closed-form based loop compensator for direct current-direct current （DC-DC） buckboost converter in discontinuous conduction with peak current-mode control is proposed to increase efficiency of the desired process through systemization. As a result, the process saves a lot of computation time that can be translated into design cost savings. Finally, the output voltage regulation in the presence of audio susceptibility and output impedance is shown for verifying.
基金Project supported by the National High Technology Research and Development Program of China (Grant No. 2008AA03Z402)the National Natural Science Foundation of China (Grant No. 61076044)the Natural Science Foundation of Beijing,China(Grant Nos. 4092007 and 4102003)
文摘A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of an oxidation- confined 850 nm VCSEL. The single-mode output power of 2.6 mW, threshold current of 0.6 mA, full width of half maximum lasing spectrum of less than 0.1 nm, side mode suppression ratio of 28.4 dB, and far-field divergence angle of about 10% are obtained. The effects of different hole depths on the optical characteristics are simulated and analysed, including far-field divergence, spectrum and lateral cavity mode. The single-mode performance of this multi-hole device is attributed to the large radiation loss from the inter hole spacing and the scattering loss at the bottom of the holes, particularly for higher order modes.
