Based on the analyses of the severity of cutting process as well as the failure mechanisms of ceramic tools, a model for designing functionally gradient ceramic tool materials with symmetrical distribution is presente...Based on the analyses of the severity of cutting process as well as the failure mechanisms of ceramic tools, a model for designing functionally gradient ceramic tool materials with symmetrical distribution is presented, by which a Al 2O 3/(W,Ti)C ceramic tool material FG 2 was developed. Multi objective optimization method was employed in designing the compositional distribution of this ceramic tool material. The results of both continuous and intermittent cutting tests are indicative of the much better cutting behavior of the functionally gradient ceramic tool FG 2 than that of the common ceramic tool SG 4.展开更多
Based on the deep understanding of the requirements of cutting conditions on ceramic tools, a design model for functionally gradient ceramic tool materials with symmetrical composition distribution was presented in th...Based on the deep understanding of the requirements of cutting conditions on ceramic tools, a design model for functionally gradient ceramic tool materials with symmetrical composition distribution was presented in this paper, according to which an Al 2O 3-TiC functionally gradient ceramic tool material FG-1 was synthesized by powder-laminating and uniaxially hot-pressing technique. The thermal shock resistance of the Al 2O 3-TiC functionally gradient ceramics FG-1 was evaluated by water quenching and subsequent three-point bending tests of flexural strength diminution. Comparisons were made with results from parallel experiments conducted using a homogeneous Al 2O 3-TiC ceramics. Functionally gradient ceramics exhibited higher retained strength under all thermal shock temperature differences compared to homogeneous ceramics, indicating the higher thermal shock resistance. The experimental results were supported by the calculation of transient thermal stress field. The cutting performance of the Al 2O 3-TiC functionally gradient ceramic tool FG-1 was also investigated in rough turning the cylindrical surface of exhaust valve of diesel engine in comparison with that of a common Al 2O 3-TiC ceramic tool LT55. The results indicated that the tool life of FG-1 increased by 50 percent over that of LT55. Tool life of LT55 was mainly controlled by thermal shock cracking which was accompanied by mechanical shock. While tool life of FG-1 was mainly controlled by mechanical fatigue crack extension rather than thermal shock cracking, revealing the less thermal shock susceptibility of functionally gradient ceramics than that of common ceramics.展开更多
Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load pheno...Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.展开更多
The influences of different impregnation temperatures,pre-oxidation,carbonization temperatures and activation conditions on the iodine value and carbon deviations was discussed.SEM,EDS,and BET techniques were used to ...The influences of different impregnation temperatures,pre-oxidation,carbonization temperatures and activation conditions on the iodine value and carbon deviations was discussed.SEM,EDS,and BET techniques were used to investigate the microstructures and properties of materials.Results showed that activated carbon functional ceramic exhibited excellent comprehensive properties when porous ceramics adsorbed the coal pitch at 150 ℃ for 0.5 h,oxidized at 420 ℃ for 1.0 h,and carbonizated at 700 ℃ for 1.0 h and then activated by using KOH（20wt%） as agent at 800 ℃ for 1.0 h,as confirmed by the high iodine value（162.6 mg/g） and high specific surface area（83.5 m2/g）.展开更多
Protonic ceramic fuel cells(PCFCs)have been attracting increasing attention because of their advances in high-efficiency power generation in an intermediate-temperature range,as compared to the high-temperature solid ...Protonic ceramic fuel cells(PCFCs)have been attracting increasing attention because of their advances in high-efficiency power generation in an intermediate-temperature range,as compared to the high-temperature solid oxide fuel cells(SOFCs).The greatest difference between PCFCs and SOFCs is the specific requirement of protonic(H+)conductivity at the PCFC cathode,in addition to the electronic(e^(-))and oxide-ion(O^(2-))conductivity.The development of a triple H^(+)/e^(-)/O^(2-)conductor for PCFC cathode is still challenging.Thus,the most-widely used cathode material is based on the mature e^(-)/O^(2-)conductor.However,this leads to insufficient triple phase boundary(TPB),i.e.,reaction area.Herein,an efficient strategy that uses a~100 nm-thick proton conductive functional layer(La_(0.5)Sr_(0.5)CoO_(3-δ),LSC55)in-between the typical La_(0.8)Sr_(0.2)CoO_(3-δ)cathode(a mature e-/O^(2-)conductor,LS C 82)and B aZr_(0.4)Ce_(0.4)Y_(0.1)Yb_(0.)1O_(3-δ)elec trolyte(11 mm in diameter,20μm in thickness)is proposed to significantly enhance the reaction area.Reasonably,the ohmic resistance and polarization resistance are both decreased by 47%and 62%,respectively,compared with that of PCFCs without the functional layer.The power density of the PCFC with such a functional layer can be raised by up to 2.24 times,superior to those described in previous reports.The enhanced PCFC performances are attributed to the well-built TPB and enhanced reaction area via the functional layer engineering strategy.展开更多
Using porous carbon hosts in cathodes of Li-S cells can disperse S actives and offset their poor electrical conductivity.However,such reservoirs would in turn absorb excess electrolyte solvents to S-unfilled regions,c...Using porous carbon hosts in cathodes of Li-S cells can disperse S actives and offset their poor electrical conductivity.However,such reservoirs would in turn absorb excess electrolyte solvents to S-unfilled regions,causing the electrolyte overconsumption,specific energy decline,and even safety hazards for battery devices.To build better cathodes,we propose to substitute carbons by In-doped SnO_(2)(ITO)nano ceramics that own three-in-one functionalities:1)using conductive ITO enables minimizing the total carbon content to an extremely low mass ratio(~3%)in cathodes,elevating the electrode tap density and averting the electrolyte overuse;2)polar ITO nanoclusters can serve as robust anchors toward Li polysulfide(LiPS)by electrostatic adsorption or chemical bond interactions;3)they offer catalysis centers for liquid–solid phase conversions of S-based actives.Also,such ceramics are intrinsically nonflammable,preventing S cathodes away from thermal runaway or explosion.These merits entail our configured cathodes with high tap density(1.54 g cm^(−3)),less electrolyte usage,good security for flame retardance,and decent Li-storage behaviors.With lean and LiNO_(3)-free electrolyte,packed full cells exhibit excellent redox kinetics,suppressed LiPS shuttling,and excellent cyclability.This may trigger great research enthusiasm in rational design of low-carbon and safer S cathodes.展开更多
Presently, the products of functional ceramic are widely applied in the light & mechatronics fields such as communication, aeronautic and astronautic engineering, military affairs and home-use electrical appliance...Presently, the products of functional ceramic are widely applied in the light & mechatronics fields such as communication, aeronautic and astronautic engineering, military affairs and home-use electrical appliance etc. It’s performance of working is mainly determined by the physical performance of the surface. And therefore the roughness and the affected layer’s depth of the final processing surface have a direct influence to the performance of the device. It is obvious that how to guarantee the processing quality of functional ceramic is a kernel problem whether it can achieve the purpose of application or not. Ultra-precision planarization is usually as the final processing method of functional ceramic substrates, and the mirror surface of Ra 0.01～0.002 μm can be obtained by ultra-precision polishing. For the ultra-precision planarization processing of functional ceramic material, simplex chemical or mechanical polishing method is very difficult to achieve the technic demands, and furthermore various defects of processing exist in the surface of crystal after planarization. However, chemical mechanical planarization (CMP) which has emerged recently as a new indispensable processing technique for higher degree planarization of functional ceramic is be able to satisfy the processing requests from the aspects of processing performance and rate. The current paper systematically introduces the processing course of functional ceramic by using chemical mechanical planarization. In addition, material removal mechanism is analyzed, and the choosing of processing conditions and components and effect of polishing slurry are discussed. Then the present research status and development trend of CMP technology for functional ceramic are discussed. Finally the current existing main questions and their solutions are presented.展开更多
The cutting properties of the functionally gradient ceramic cutting tools relate closely to the gradient distribution. A cutting model of the functionally gradient ceramic tool is firstly designed in the present paper...The cutting properties of the functionally gradient ceramic cutting tools relate closely to the gradient distribution. A cutting model of the functionally gradient ceramic tool is firstly designed in the present paper. The optimum of gradient distribution is obtained by way of the FEM analyses.展开更多
The local structure of an alternative Pb（Zn1/3Nb2/3）O3-based perovskite ceramic is investigated. The 0.07BaTiO33-0.93Pb（Zn1/3Nb2/3）O3 ceramic is synthesized using a combination of Zn3Nb2O8 B-site precursor and BaT...The local structure of an alternative Pb（Zn1/3Nb2/3）O3-based perovskite ceramic is investigated. The 0.07BaTiO33-0.93Pb（Zn1/3Nb2/3）O3 ceramic is synthesized using a combination of Zn3Nb2O8 B-site precursor and BaTiO33 perovskite phase stabilizer. Then, x-ray absorption spectroscopy and density functional theory are employed to calculate the local structure configuration and formation energy of the prepared samples. Ba2＋ is found to replace Pb2＋ in AA-site with Zn2＋ occupying BB-site in Pb（Zn1/3Nb2/3）O3, while in the neighboring structure, Ti4＋4＋ replaces Nb5＋5＋ in BB-site with Pb2＋2＋ occupying AA-site. With the substitution of BaTiO33 in Pb（Zn1/3Nb2/3）O3, the bond length between Zn2＋ and Pb2＋ is longer than that of the typical perovskite phase of Pb（Zn1/3Nb2/3）O3. This indicates the key role of BaTiO33 in decreasing the steric hindrance of Pb2＋ lone pair, and the mutual interactions between Pb2＋ lone pair and Zn2＋ and the formation energy is seen to decrease. This finding of the formation energy and local structure configuration relationship can further extend a fundamental understanding of the role of BaTiO33 in stabilizing the perovskite phase in PbZn13Nb23O3-based materials, which in turn will lead to an improved preparation technique for desired electrical properties.展开更多
A nonlinear finite element method is applied to observe how inclusion shape influence the thermal response of a ceramic-metal functionally graded material (FGM). The elastic and plastic behaviors of the layers which a...A nonlinear finite element method is applied to observe how inclusion shape influence the thermal response of a ceramic-metal functionally graded material (FGM). The elastic and plastic behaviors of the layers which are two-phase isotropic composites consisting of randomly oriented elastic spheroidal Inclusions and a ductile matrix are predicted by cc mean field method. The prediction results show that inclusion shape has remarkable influence on the overall behavior of the composite. The consequences of the thermal response analysis of the FGM are that the response is dependent on inclusion shape and its composition profile cooperatively and that the plastic behavior of each layer should be taken into account in optimum design of a ceramic-metal FGM.展开更多
Hydrogen stands as a promising energy carrier that plays a pivotal role in addressing global sustainability and achieving carbon neutrality.The conversion of hydrogen energy through fuel cells has emerged as a central...Hydrogen stands as a promising energy carrier that plays a pivotal role in addressing global sustainability and achieving carbon neutrality.The conversion of hydrogen energy through fuel cells has emerged as a central technology in this pursuit.Notably,protonic ceramic fuel cells(PCFCs)hold potential for the future hydrogen energy ecosystem,owing to their impressive energy conversion efficiencies at low-to-intermediate temperatures(300-750℃).It is becoming increasingly evident that the development of PCFC technology relies on advancements in the cathode,as oxygen-involved reactions often exhibit sluggish kinetics.In this comprehensive review,we aim to provide an overview of the current state of knowledge concerning the design of advanced cathodes for PCFCs.This includes discussing key descriptors for cathodes,methods for characterizing material properties,and functionalization techniques to enhance electrode performance.Finally,we present insights into future research directions.展开更多
Graphene nanoplatelets(GNPs)are considered to be one of the most promising new reinforcements due to their unique two-dimensional structure and remarkable mechanical properties.In addition,their impressive electrical ...Graphene nanoplatelets(GNPs)are considered to be one of the most promising new reinforcements due to their unique two-dimensional structure and remarkable mechanical properties.In addition,their impressive electrical and thermal properties make them attractive fillers for producing multifunctional ceramics with a wide range of applications.This paper reviews the current status of the research and development of graphene-reinforced ceramic matrix composite(CMC)materials.Firstly,we focused on the processing methods for effective dispersion of GNPs throughout ceramic matrices and the reduction of the porosity of CMC products.Then,the microstructure and mechanical properties are provided,together with an emphasis on the possible toughening mechanisms that may operate.Additionally,the unique functional properties endowed by GNPs,such as enhanced electrical/thermal conductivity,are discussed,with a comprehensive comparison in different ceramic matrices as oxide and nonoxide composites.Finally,the prospects and problems needed to be solved in GNPs-reinforced CMCs are discussed.展开更多
In order to utilize solid wastes, ceramic facing brick was made form East-lake sediment and some additives. The strength and freeze-thaw resistance of the samples were tested, and the crystal phases and microstructure...In order to utilize solid wastes, ceramic facing brick was made form East-lake sediment and some additives. The strength and freeze-thaw resistance of the samples were tested, and the crystal phases and microstructures were studied by XRD and SEM. The results indicate that the samples have a wide firing temperature range. The main crystal phases are CaA12SizOs, a-Al203, Fe203, which distribute uniformly in the samples. The sample have the best properties in the series ＇Ca-A1-Si＇, and water absorption （Wa）, porosity （Pa）, bulk density （D）, bending strength and compressive strength are 7.24%, 15.82%, 2.19 g.cm＂3, 45.57 MPa and 56.81 MPa respectively, when the addition amount of East-lake sediment is 80% and the firing temperature is 1 100 ~C. In the series ＇K-A1-Si＇, the sample with the best properties was obtained when addition amount of East-lake sediment was 70% and firing temperature was 1 060 ~C. The water absorption, porosity, bulk density, bending strength and compressive strength are 7.62%, 16.37%, 2.15 g ~ cm＂3, 39.26 MPa, and 50.81 MPa respectively. They all come up to the national standardization, and meet the needs of manufacturing production.展开更多
The gaseous Pr-penetration is a new method to modify ceramics, which is expected to be a promising method for producing new conductor ceramic materials. The gaseous penetration of Pr into PbTiO_3 ceramics and their im...The gaseous Pr-penetration is a new method to modify ceramics, which is expected to be a promising method for producing new conductor ceramic materials. The gaseous penetration of Pr into PbTiO_3 ceramics and their improved electric properties were reported. Through XRD, EPMA and SEM analysis,it is confirmed that the gaseous penetration makes Pr enter into PbTiO_3 ceramics, and the new compound of Pr_2Ti_2O_7 is formed by the penetration of Pr in the gaseous state. The formed new Pr_2Ti_2O_7-PbTiO_3 ceramic materials have a significant change in electric properties. The room temperature resistivity decreases from 2.0×10^(10) Ω·m to 9.487 Ω·m. The grain resistance and the grain boundary resistance decrease with increase in temperature, and the PTCR effect disappears. The tendency of transition to a conductive body is manifest.展开更多
Aluminium hybrid functionally graded metal matrix composites(FGMMCs),meet growing demands for supreme tribo-mechanical performance in automotive and aviation industry.This research experimentally compares the influenc...Aluminium hybrid functionally graded metal matrix composites(FGMMCs),meet growing demands for supreme tribo-mechanical performance in automotive and aviation industry.This research experimentally compares the influence of carbide ceramics(B_(4)C,SiC,TiC)as reinforcements,in improving reciprocating tribology performance and mechanical strength of A333 hybrid composites against alloy.Hollow cylindrical samples of A333/6 wt%B_(4)C/4 wt%TiC and A333/6 wt%B_(4)C/4 wt%SiC hybrid FGMMCs were developed using horizontal centrifugal casting.Metallography analysis on both composites revealed increasing ceramic gradient distribution towards outer composite wall.Particle rich zone of A333/B_(4)C/SiC hybrid FGMMC showed maximum micro-hardness(198.9 HV)and tensile strength(267.9 MPa).Elemental mapping confirmed effective distribution of ceramics and detected elemental composition of both composites.Particle rich layer of A333/B_(4)C/SiC hybrid FGMMC exhibited improved wear resistance in comparison with all three layers of A333/B_(4)C/TiC hybrid FGMMC and alloy.Third-body abrasion and tribo-chemical wear were the predominant mechanisms revealed for both composites during worn surface analysis.展开更多
This paper presents a study on nonlinear vibration of inhomogeneous functional plates composed of sigmoid graded metalceramic materials. The material properties vary continuously along the thickness direction accordin...This paper presents a study on nonlinear vibration of inhomogeneous functional plates composed of sigmoid graded metalceramic materials. The material properties vary continuously along the thickness direction according to a sigmoid distribution rule, which is defined by piecewise functions to ensure smooth distribution of stress among all the interfaces. The geometric nonlinearity is considered by adopting the von Kármán geometrical relations. Based on the d'Alembert's principle, the nonlinear out-of-plane equation of motion of the plates is developed. The Galerkin method is employed to discretize the motion equation to a series of ordinary differential ones, which are subsequently analyzed via the use of the method of harmonic balance. Then, the analytical results are validated by the comparison to numerical solutions, which are obtained by using the adaptive step-size fourth-order Runge-Kutta method. The stability of the steady-state response is examined by the perturbation technique. Results show the first and third modes are both activated while the second mode is not activated for the plates under harmonic point excitation. The frequency response relationships of activated modes exhibit very complicated curves due to the nonlinear modal interaction. In addition, influences of key system parameters on nonlinear vibrational characteristics of the present inhomogeneous plates are illustrated.展开更多
A super-hydrophilic functional ceramic was prepared by adjusting the chemical components of ceramic glaze. Effect of surface free energy of ceramic glaze on oil droplet shape and its behavior in water were studied. Th...A super-hydrophilic functional ceramic was prepared by adjusting the chemical components of ceramic glaze. Effect of surface free energy of ceramic glaze on oil droplet shape and its behavior in water were studied. The results show that water can spread on ceramic surface with high surface free energy, and oil droplet can aggregate rapidly and separate from the ceramic surface in water. For the ceramic with lower surface free energy, the polar shares are dependant on its easy-cleaning property. The higher the polar shares, the better the easy-cleaning property, and the easier the droplet separates from the ceramic surface in water.展开更多
Graphene-incorporated ceramics are recognized as promising candidates for various tribological applications,including machining tools,nozzles,mechanical seals,bearings,and gears.Generally,graphene-incorporated ceramic...Graphene-incorporated ceramics are recognized as promising candidates for various tribological applications,including machining tools,nozzles,mechanical seals,bearings,and gears.Generally,graphene-incorporated ceramics exhibit lower friction coefficients and wear rates compared to ceramic composites reinforced by other lubricants,including CaF5,MoS2,h-BN,carbon fiber,and CNTs.This review comprehensively summarizes the current knowledge of the tribological performance of graphene-reinforced ceramics,highlighting the effects of in situ grown graphene,core-shell structured graphene,three-dimensional assembled graphene,and functionally graded graphene on the friction and wear properties of ceramics.In situ graphene forms stable lubrication films,effectively reducing the friction coefficient of the ceramic matrix.Core-shell structured graphene ceramics achieve outstanding wear resistance through rolling friction mechanisms and crack inhibition.Three-dimensional assembled graphene enhances the stability of lubrication films and contributes to superior friction reduction.Functionally graded graphene ceramics optimize internal structures,improving impact resistance and tribological stability.Furthermore,the challenges and future development directions of graphene-incorporated ceramics are discussed,highlighting their promising applications in high-temperature,extreme environments,and precision mechanical systems.展开更多
This paper provides a brief review of current research activities that focus on the synthesis and controlled assembly of inorganic nano-bers by electrospinning,their electrical,optical and magnetic properties,as well ...This paper provides a brief review of current research activities that focus on the synthesis and controlled assembly of inorganic nano-bers by electrospinning,their electrical,optical and magnetic properties,as well as their applications in various areas including sensors,catalysts,batteries,filters and separators.We begin with a brief introduction to electrospinning technology and a brief method to produce ceramic nanofibers from electrospinning.We then discuss approaches to the controlled assembly and patterning of electrospun ceramic nanofibers.We continue with a highlight of some recent applications enabled by electrospun ceramic nano-bers,with a focus on the physical properties of functional ceramic nanofibers as well as their applications in energy and environmental technologies.In the end,we conclude this review with some perspectives on the future directions and implications for this new class of functional nanomaterials.It is expected that this review paper can help the readers quickly become acquainted with the basic principles and particularly the experimental procedure for preparing and assembly of 1D ceramic nanofiber and its arrays.展开更多
The idea of functionally gradient material (FGM) theory was used to design ceramic nozzle based on the erosion wear behaviors of the ceramic nozzles and the out- standing properties of FGM. The purpose is to reduce th...The idea of functionally gradient material (FGM) theory was used to design ceramic nozzle based on the erosion wear behaviors of the ceramic nozzles and the out- standing properties of FGM. The purpose is to reduce the tensile stress at the entry region of the nozzle during sand blasting processes. The design theory and methods of gradient ceramic nozzle were proposed. The physical, micromechanical, and composition distribution models of gradient ceramic nozzle were established. The optimum composition distribution of the gradient ceramic nozzle material was determined from the solution of the multi-objective optimization calculation by constructing the models of the composition distribution versus the structural in- tegrity of the compact in fabricating process. Results showed that compressive residual stresses appeared at the entry area of the gradient ceramic nozzle. The optimized component distribution exponent p is 0.5. An SiC/(W,Ti)C gradient ce- ramic nozzle material was synthesized by hot-pressing according to the design result. Results showed that the surface Vickers hardness of the FGM-1 gradient ceramic nozzle materials was greatly improved in comparison with that of the other layers.展开更多
文摘Based on the analyses of the severity of cutting process as well as the failure mechanisms of ceramic tools, a model for designing functionally gradient ceramic tool materials with symmetrical distribution is presented, by which a Al 2O 3/(W,Ti)C ceramic tool material FG 2 was developed. Multi objective optimization method was employed in designing the compositional distribution of this ceramic tool material. The results of both continuous and intermittent cutting tests are indicative of the much better cutting behavior of the functionally gradient ceramic tool FG 2 than that of the common ceramic tool SG 4.
文摘Based on the deep understanding of the requirements of cutting conditions on ceramic tools, a design model for functionally gradient ceramic tool materials with symmetrical composition distribution was presented in this paper, according to which an Al 2O 3-TiC functionally gradient ceramic tool material FG-1 was synthesized by powder-laminating and uniaxially hot-pressing technique. The thermal shock resistance of the Al 2O 3-TiC functionally gradient ceramics FG-1 was evaluated by water quenching and subsequent three-point bending tests of flexural strength diminution. Comparisons were made with results from parallel experiments conducted using a homogeneous Al 2O 3-TiC ceramics. Functionally gradient ceramics exhibited higher retained strength under all thermal shock temperature differences compared to homogeneous ceramics, indicating the higher thermal shock resistance. The experimental results were supported by the calculation of transient thermal stress field. The cutting performance of the Al 2O 3-TiC functionally gradient ceramic tool FG-1 was also investigated in rough turning the cylindrical surface of exhaust valve of diesel engine in comparison with that of a common Al 2O 3-TiC ceramic tool LT55. The results indicated that the tool life of FG-1 increased by 50 percent over that of LT55. Tool life of LT55 was mainly controlled by thermal shock cracking which was accompanied by mechanical shock. While tool life of FG-1 was mainly controlled by mechanical fatigue crack extension rather than thermal shock cracking, revealing the less thermal shock susceptibility of functionally gradient ceramics than that of common ceramics.
基金Sponsored by the 2007 Fujian University and College New Century Excellent Talent Support Program (No. XSJRC2007-17)Natural Science Foundation of Fujian Province (No. 2010J01279)
文摘Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.
基金sponsored by Fujian Scientific and Technological Department (Nos.2004I003 and 2006N0037)
文摘The influences of different impregnation temperatures,pre-oxidation,carbonization temperatures and activation conditions on the iodine value and carbon deviations was discussed.SEM,EDS,and BET techniques were used to investigate the microstructures and properties of materials.Results showed that activated carbon functional ceramic exhibited excellent comprehensive properties when porous ceramics adsorbed the coal pitch at 150 ℃ for 0.5 h,oxidized at 420 ℃ for 1.0 h,and carbonizated at 700 ℃ for 1.0 h and then activated by using KOH（20wt%） as agent at 800 ℃ for 1.0 h,as confirmed by the high iodine value（162.6 mg/g） and high specific surface area（83.5 m2/g）.
基金financially supported by China Post-doctoral Science Foundation(No.2022M710856)Guangzhou Postdoctoral Research Project(No.62104380)+2 种基金the Outstanding Youth Project of Natural Science Foundation of Guangdong Province(No.2022B1515020020)the Funding by Science and Technology Projects in Guangzhou(Nos.202206050003 and 202201010603)Guangdong Engineering Technology Research Center for Hydrogen Energy and Fuel Cells。
文摘Protonic ceramic fuel cells(PCFCs)have been attracting increasing attention because of their advances in high-efficiency power generation in an intermediate-temperature range,as compared to the high-temperature solid oxide fuel cells(SOFCs).The greatest difference between PCFCs and SOFCs is the specific requirement of protonic(H+)conductivity at the PCFC cathode,in addition to the electronic(e^(-))and oxide-ion(O^(2-))conductivity.The development of a triple H^(+)/e^(-)/O^(2-)conductor for PCFC cathode is still challenging.Thus,the most-widely used cathode material is based on the mature e^(-)/O^(2-)conductor.However,this leads to insufficient triple phase boundary(TPB),i.e.,reaction area.Herein,an efficient strategy that uses a~100 nm-thick proton conductive functional layer(La_(0.5)Sr_(0.5)CoO_(3-δ),LSC55)in-between the typical La_(0.8)Sr_(0.2)CoO_(3-δ)cathode(a mature e-/O^(2-)conductor,LS C 82)and B aZr_(0.4)Ce_(0.4)Y_(0.1)Yb_(0.)1O_(3-δ)elec trolyte(11 mm in diameter,20μm in thickness)is proposed to significantly enhance the reaction area.Reasonably,the ohmic resistance and polarization resistance are both decreased by 47%and 62%,respectively,compared with that of PCFCs without the functional layer.The power density of the PCFC with such a functional layer can be raised by up to 2.24 times,superior to those described in previous reports.The enhanced PCFC performances are attributed to the well-built TPB and enhanced reaction area via the functional layer engineering strategy.
基金support by the National Natural Science Foundation of China(51802269,21773138)Fundamental Research Funds for the Central Universities(XDJK2019AA002)+1 种基金the Venture&Innovation Support Program for Chongqing Overseas Returnees(cx2018027)the innovation platform for academicians of Hainan province.
文摘Using porous carbon hosts in cathodes of Li-S cells can disperse S actives and offset their poor electrical conductivity.However,such reservoirs would in turn absorb excess electrolyte solvents to S-unfilled regions,causing the electrolyte overconsumption,specific energy decline,and even safety hazards for battery devices.To build better cathodes,we propose to substitute carbons by In-doped SnO_(2)(ITO)nano ceramics that own three-in-one functionalities:1)using conductive ITO enables minimizing the total carbon content to an extremely low mass ratio(~3%)in cathodes,elevating the electrode tap density and averting the electrolyte overuse;2)polar ITO nanoclusters can serve as robust anchors toward Li polysulfide(LiPS)by electrostatic adsorption or chemical bond interactions;3)they offer catalysis centers for liquid–solid phase conversions of S-based actives.Also,such ceramics are intrinsically nonflammable,preventing S cathodes away from thermal runaway or explosion.These merits entail our configured cathodes with high tap density(1.54 g cm^(−3)),less electrolyte usage,good security for flame retardance,and decent Li-storage behaviors.With lean and LiNO_(3)-free electrolyte,packed full cells exhibit excellent redox kinetics,suppressed LiPS shuttling,and excellent cyclability.This may trigger great research enthusiasm in rational design of low-carbon and safer S cathodes.
文摘Presently, the products of functional ceramic are widely applied in the light & mechatronics fields such as communication, aeronautic and astronautic engineering, military affairs and home-use electrical appliance etc. It’s performance of working is mainly determined by the physical performance of the surface. And therefore the roughness and the affected layer’s depth of the final processing surface have a direct influence to the performance of the device. It is obvious that how to guarantee the processing quality of functional ceramic is a kernel problem whether it can achieve the purpose of application or not. Ultra-precision planarization is usually as the final processing method of functional ceramic substrates, and the mirror surface of Ra 0.01～0.002 μm can be obtained by ultra-precision polishing. For the ultra-precision planarization processing of functional ceramic material, simplex chemical or mechanical polishing method is very difficult to achieve the technic demands, and furthermore various defects of processing exist in the surface of crystal after planarization. However, chemical mechanical planarization (CMP) which has emerged recently as a new indispensable processing technique for higher degree planarization of functional ceramic is be able to satisfy the processing requests from the aspects of processing performance and rate. The current paper systematically introduces the processing course of functional ceramic by using chemical mechanical planarization. In addition, material removal mechanism is analyzed, and the choosing of processing conditions and components and effect of polishing slurry are discussed. Then the present research status and development trend of CMP technology for functional ceramic are discussed. Finally the current existing main questions and their solutions are presented.
基金supported by the National Natural Science Foundation of China(59875091)
文摘The cutting properties of the functionally gradient ceramic cutting tools relate closely to the gradient distribution. A cutting model of the functionally gradient ceramic tool is firstly designed in the present paper. The optimum of gradient distribution is obtained by way of the FEM analyses.
基金Supported by the Thailand Research Fund under Grant No TRG5880097
文摘The local structure of an alternative Pb（Zn1/3Nb2/3）O3-based perovskite ceramic is investigated. The 0.07BaTiO33-0.93Pb（Zn1/3Nb2/3）O3 ceramic is synthesized using a combination of Zn3Nb2O8 B-site precursor and BaTiO33 perovskite phase stabilizer. Then, x-ray absorption spectroscopy and density functional theory are employed to calculate the local structure configuration and formation energy of the prepared samples. Ba2＋ is found to replace Pb2＋ in AA-site with Zn2＋ occupying BB-site in Pb（Zn1/3Nb2/3）O3, while in the neighboring structure, Ti4＋4＋ replaces Nb5＋5＋ in BB-site with Pb2＋2＋ occupying AA-site. With the substitution of BaTiO33 in Pb（Zn1/3Nb2/3）O3, the bond length between Zn2＋ and Pb2＋ is longer than that of the typical perovskite phase of Pb（Zn1/3Nb2/3）O3. This indicates the key role of BaTiO33 in decreasing the steric hindrance of Pb2＋ lone pair, and the mutual interactions between Pb2＋ lone pair and Zn2＋ and the formation energy is seen to decrease. This finding of the formation energy and local structure configuration relationship can further extend a fundamental understanding of the role of BaTiO33 in stabilizing the perovskite phase in PbZn13Nb23O3-based materials, which in turn will lead to an improved preparation technique for desired electrical properties.
基金Funded by National Science Foundation of China(Grant:1987205).
文摘A nonlinear finite element method is applied to observe how inclusion shape influence the thermal response of a ceramic-metal functionally graded material (FGM). The elastic and plastic behaviors of the layers which are two-phase isotropic composites consisting of randomly oriented elastic spheroidal Inclusions and a ductile matrix are predicted by cc mean field method. The prediction results show that inclusion shape has remarkable influence on the overall behavior of the composite. The consequences of the thermal response analysis of the FGM are that the response is dependent on inclusion shape and its composition profile cooperatively and that the plastic behavior of each layer should be taken into account in optimum design of a ceramic-metal FGM.
基金National Research Foundation of Korea,Grant/Award Number:RS-2023-00278820Korea Electric Power Corporation,Grant/Award Number:R23XO07-02。
文摘Hydrogen stands as a promising energy carrier that plays a pivotal role in addressing global sustainability and achieving carbon neutrality.The conversion of hydrogen energy through fuel cells has emerged as a central technology in this pursuit.Notably,protonic ceramic fuel cells(PCFCs)hold potential for the future hydrogen energy ecosystem,owing to their impressive energy conversion efficiencies at low-to-intermediate temperatures(300-750℃).It is becoming increasingly evident that the development of PCFC technology relies on advancements in the cathode,as oxygen-involved reactions often exhibit sluggish kinetics.In this comprehensive review,we aim to provide an overview of the current state of knowledge concerning the design of advanced cathodes for PCFCs.This includes discussing key descriptors for cathodes,methods for characterizing material properties,and functionalization techniques to enhance electrode performance.Finally,we present insights into future research directions.
基金financially supported by the National Natural Science Foundation of China(Nos.51432004 and 51672041)the Fundamental Research Funds for the Central Universities(No.2232018G-07)+2 种基金the Innovation Program of Shanghai Municipal Education Commission(No.2017-01-07-00-03-E00025)the Program for Innovative Research Team in University of Ministry of Education of China(No.IRT_16R13)Shanghai Sailing Program(No.17YF1400400)。
文摘Graphene nanoplatelets(GNPs)are considered to be one of the most promising new reinforcements due to their unique two-dimensional structure and remarkable mechanical properties.In addition,their impressive electrical and thermal properties make them attractive fillers for producing multifunctional ceramics with a wide range of applications.This paper reviews the current status of the research and development of graphene-reinforced ceramic matrix composite(CMC)materials.Firstly,we focused on the processing methods for effective dispersion of GNPs throughout ceramic matrices and the reduction of the porosity of CMC products.Then,the microstructure and mechanical properties are provided,together with an emphasis on the possible toughening mechanisms that may operate.Additionally,the unique functional properties endowed by GNPs,such as enhanced electrical/thermal conductivity,are discussed,with a comprehensive comparison in different ceramic matrices as oxide and nonoxide composites.Finally,the prospects and problems needed to be solved in GNPs-reinforced CMCs are discussed.
文摘In order to utilize solid wastes, ceramic facing brick was made form East-lake sediment and some additives. The strength and freeze-thaw resistance of the samples were tested, and the crystal phases and microstructures were studied by XRD and SEM. The results indicate that the samples have a wide firing temperature range. The main crystal phases are CaA12SizOs, a-Al203, Fe203, which distribute uniformly in the samples. The sample have the best properties in the series ＇Ca-A1-Si＇, and water absorption （Wa）, porosity （Pa）, bulk density （D）, bending strength and compressive strength are 7.24%, 15.82%, 2.19 g.cm＂3, 45.57 MPa and 56.81 MPa respectively, when the addition amount of East-lake sediment is 80% and the firing temperature is 1 100 ~C. In the series ＇K-A1-Si＇, the sample with the best properties was obtained when addition amount of East-lake sediment was 70% and firing temperature was 1 060 ~C. The water absorption, porosity, bulk density, bending strength and compressive strength are 7.62%, 16.37%, 2.15 g ~ cm＂3, 39.26 MPa, and 50.81 MPa respectively. They all come up to the national standardization, and meet the needs of manufacturing production.
文摘The gaseous Pr-penetration is a new method to modify ceramics, which is expected to be a promising method for producing new conductor ceramic materials. The gaseous penetration of Pr into PbTiO_3 ceramics and their improved electric properties were reported. Through XRD, EPMA and SEM analysis,it is confirmed that the gaseous penetration makes Pr enter into PbTiO_3 ceramics, and the new compound of Pr_2Ti_2O_7 is formed by the penetration of Pr in the gaseous state. The formed new Pr_2Ti_2O_7-PbTiO_3 ceramic materials have a significant change in electric properties. The room temperature resistivity decreases from 2.0×10^(10) Ω·m to 9.487 Ω·m. The grain resistance and the grain boundary resistance decrease with increase in temperature, and the PTCR effect disappears. The tendency of transition to a conductive body is manifest.
文摘Aluminium hybrid functionally graded metal matrix composites(FGMMCs),meet growing demands for supreme tribo-mechanical performance in automotive and aviation industry.This research experimentally compares the influence of carbide ceramics(B_(4)C,SiC,TiC)as reinforcements,in improving reciprocating tribology performance and mechanical strength of A333 hybrid composites against alloy.Hollow cylindrical samples of A333/6 wt%B_(4)C/4 wt%TiC and A333/6 wt%B_(4)C/4 wt%SiC hybrid FGMMCs were developed using horizontal centrifugal casting.Metallography analysis on both composites revealed increasing ceramic gradient distribution towards outer composite wall.Particle rich zone of A333/B_(4)C/SiC hybrid FGMMC showed maximum micro-hardness(198.9 HV)and tensile strength(267.9 MPa).Elemental mapping confirmed effective distribution of ceramics and detected elemental composition of both composites.Particle rich layer of A333/B_(4)C/SiC hybrid FGMMC exhibited improved wear resistance in comparison with all three layers of A333/B_(4)C/TiC hybrid FGMMC and alloy.Third-body abrasion and tribo-chemical wear were the predominant mechanisms revealed for both composites during worn surface analysis.
基金supported by the National Natural Science Foundation of China(Grant Nos.11672071,11302046 and 11672072)the Fundamental Research Funds for the Central Universities(Grant No N170504023)
文摘This paper presents a study on nonlinear vibration of inhomogeneous functional plates composed of sigmoid graded metalceramic materials. The material properties vary continuously along the thickness direction according to a sigmoid distribution rule, which is defined by piecewise functions to ensure smooth distribution of stress among all the interfaces. The geometric nonlinearity is considered by adopting the von Kármán geometrical relations. Based on the d'Alembert's principle, the nonlinear out-of-plane equation of motion of the plates is developed. The Galerkin method is employed to discretize the motion equation to a series of ordinary differential ones, which are subsequently analyzed via the use of the method of harmonic balance. Then, the analytical results are validated by the comparison to numerical solutions, which are obtained by using the adaptive step-size fourth-order Runge-Kutta method. The stability of the steady-state response is examined by the perturbation technique. Results show the first and third modes are both activated while the second mode is not activated for the plates under harmonic point excitation. The frequency response relationships of activated modes exhibit very complicated curves due to the nonlinear modal interaction. In addition, influences of key system parameters on nonlinear vibrational characteristics of the present inhomogeneous plates are illustrated.
文摘A super-hydrophilic functional ceramic was prepared by adjusting the chemical components of ceramic glaze. Effect of surface free energy of ceramic glaze on oil droplet shape and its behavior in water were studied. The results show that water can spread on ceramic surface with high surface free energy, and oil droplet can aggregate rapidly and separate from the ceramic surface in water. For the ceramic with lower surface free energy, the polar shares are dependant on its easy-cleaning property. The higher the polar shares, the better the easy-cleaning property, and the easier the droplet separates from the ceramic surface in water.
基金the National Natural Science Foundation of China(52375451,52005396)Shandong Provincial Natural Science Foundation(ZR2023YQ052)+6 种基金Young Taishan Scholars Program of Shandong Province(tsqn202306041)Guandong Basic and Applied Basic Research Foundation(2023A1515010044)Shandong Provincial Youth Innovation Team(2022KJ038)Open Project of State Key Laboratory of Solid Lubrication(LSL-22-11)Shandong Provincial Technological SME Innovation Capability Promotion Project(2023TSGC0848)Instrument Improvement Funds of Shandong University Public Technology Platform(20230113)Qilu Youth Scholar Project Funding of Shandong University。
文摘Graphene-incorporated ceramics are recognized as promising candidates for various tribological applications,including machining tools,nozzles,mechanical seals,bearings,and gears.Generally,graphene-incorporated ceramics exhibit lower friction coefficients and wear rates compared to ceramic composites reinforced by other lubricants,including CaF5,MoS2,h-BN,carbon fiber,and CNTs.This review comprehensively summarizes the current knowledge of the tribological performance of graphene-reinforced ceramics,highlighting the effects of in situ grown graphene,core-shell structured graphene,three-dimensional assembled graphene,and functionally graded graphene on the friction and wear properties of ceramics.In situ graphene forms stable lubrication films,effectively reducing the friction coefficient of the ceramic matrix.Core-shell structured graphene ceramics achieve outstanding wear resistance through rolling friction mechanisms and crack inhibition.Three-dimensional assembled graphene enhances the stability of lubrication films and contributes to superior friction reduction.Functionally graded graphene ceramics optimize internal structures,improving impact resistance and tribological stability.Furthermore,the challenges and future development directions of graphene-incorporated ceramics are discussed,highlighting their promising applications in high-temperature,extreme environments,and precision mechanical systems.
基金the National Natural Science Foundation of China(Nos.50872063,50990302,and 51072088).
文摘This paper provides a brief review of current research activities that focus on the synthesis and controlled assembly of inorganic nano-bers by electrospinning,their electrical,optical and magnetic properties,as well as their applications in various areas including sensors,catalysts,batteries,filters and separators.We begin with a brief introduction to electrospinning technology and a brief method to produce ceramic nanofibers from electrospinning.We then discuss approaches to the controlled assembly and patterning of electrospun ceramic nanofibers.We continue with a highlight of some recent applications enabled by electrospun ceramic nano-bers,with a focus on the physical properties of functional ceramic nanofibers as well as their applications in energy and environmental technologies.In the end,we conclude this review with some perspectives on the future directions and implications for this new class of functional nanomaterials.It is expected that this review paper can help the readers quickly become acquainted with the basic principles and particularly the experimental procedure for preparing and assembly of 1D ceramic nanofiber and its arrays.
基金the Specialized Research Fund for Doctoral Program of Higher Education (Grant No. 20030422105)the Natural Science Founda-tion of Shandong Province (Grant Nos. Y2004F08, Z2003F01)the Program for New Century Excellent Talents in University (Grant No. NCET-04-0622)
文摘The idea of functionally gradient material (FGM) theory was used to design ceramic nozzle based on the erosion wear behaviors of the ceramic nozzles and the out- standing properties of FGM. The purpose is to reduce the tensile stress at the entry region of the nozzle during sand blasting processes. The design theory and methods of gradient ceramic nozzle were proposed. The physical, micromechanical, and composition distribution models of gradient ceramic nozzle were established. The optimum composition distribution of the gradient ceramic nozzle material was determined from the solution of the multi-objective optimization calculation by constructing the models of the composition distribution versus the structural in- tegrity of the compact in fabricating process. Results showed that compressive residual stresses appeared at the entry area of the gradient ceramic nozzle. The optimized component distribution exponent p is 0.5. An SiC/(W,Ti)C gradient ce- ramic nozzle material was synthesized by hot-pressing according to the design result. Results showed that the surface Vickers hardness of the FGM-1 gradient ceramic nozzle materials was greatly improved in comparison with that of the other layers.
