Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic ...Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic rolled SF-7055 Al alloy is elongated to form a fiber texture.Numerous proliferating dislocations in the microstructure accumulate into dislocation walls and cells,and eventually form subgrains.These subgrain boundaries divide the original grain,thereby reducing the grain size.Under severe deformation conditions,they even enable the formation of nanograins.Meanwhile,the Cu-rich precipitates in the matrix are also broken and refined under the action of large rolling stress.In the process of cryogenic rolling,the tensile strength and hardness of SF-7055 Al alloy gradually increase,while the plasticity decreases.Moreover,the fracture morphology of cryogenic rolled SF-7055 Al alloy gradually transforms to the ductile and quasi-cleavage hybrid fracture characteristics with increased reduction.展开更多
The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepar...The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepared by vacuum arc melting.The microstructure,mechanical properties,and related influencing mechanisms were systematically investigated.The results indicate that the solidification microstructure of the Ti46Al1.5Cr8Nb-xTa alloys comprises theγ-TiAl phase,α_(2)-Ti_(3)Al phase,and B2 phase.As the Ta content increases from 0.2 at.%to 1.0 at.%,the content ofα_(2)phase and B2 phase increases,while theγphase content decreases.Among them,the B2 phase shows the most pronounced change,being significantly refined,with its content increasing from 12.49%to 21.91%.In addition,the average size of the lamellar colony decreases from 160.65 to 94.44μm.The addition of the Ta element shifts the solidification path toward lower aluminum concentrations,leading to changes in phase content.The tantalum-induced increase in the B2 phase and enhanced supercooling at the solidification front provide the basis for lamellar colony refinement.Compressive testing at room temperature reveals that the Ti46 Al1.5 Cr8 Nb0.4 Ta alloy exhibits optimal compressive properties,achieving a compressive strength of 2,434 MPa and a compressive strain of 33.1%.The improvement of its properties is attributed to a combination of lamellar colony refinement,solid solution strengthening resulting from the incorporation of Ta element,and a reduction in the c/a of theγphase.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of re...Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of recycled coral aggregate on concrete properties,this study performed a comprehensive analysis of the physical properties of recycled coral aggregate and the basic mechanical properties and microstructure of RCAC.The test results indicate that,compared to coral debris,the crushing index of recycled coral aggregate was reduced by 9.4%,while porosity decreased by 33.5%.Furthermore,RCAC retained the early strength characteristics of coral concrete,with compressive strength and flexural strength exhibiting a notable increase as the water-cement ratio decreased.Under identical conditions,the compressive strength and flexural strength of RCAC were 12.7% and 2.5% higher than coral concrete's,respectively,with porosity correspondingly reduced from 3.13% to 5.11%.This enhancement could be attributed to the new mortar filling the recycled coral aggregate.Scanning electron microscopy(SEM)analysis revealed three distinct interface transition zones within RCAC,with the‘new mortar-old mortar’interface identified as the weakest.The above findings provided a reference for the sustainable use of coral concrete in constructing offshore islands.展开更多
To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrough...To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrought Zn−0.1Mg alloy by annealing at 200℃ for varying durations.The findings reveal that the tensile strength of the alloy rapidly and significantly declines with prolonged annealing time,decreasing from 383 MPa for the as-received alloy to 102 MPa for the alloy subjected to 1440 min of annealing.The primary factors contributing to this considerable reduction in strength are static recrystallization,grain coarsening,and dislocation annihilation.Initially,the ductility of the alloy shows fluctuations,ultimately experiencing a marked decrease after extended annealing.This decline is linked to the grain growth and heightened texture intensity,while the unusual increase in ductility observed between 30 and 120 min of annealing is likely due to the formation of twins.In addition,due to rapid grain growth and an increase in precipitates and twins,the corrosion resistance of the alloy in Hank’s solution has worsened,with the corrosion rate rising from 0.037 to 0.069 mm/a following 300 min of annealing.展开更多
The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding ...The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding 0.2 wt.%Mn to T6-treated Al−Si−Mg alloys enhanced the corrosion resistance by promoting the formation ofα-AlFeMnSi phase,characterized by smaller absolute Volta potential values compared to eutectic Si,β-AlFeSi andπ-AlFeMgSi phases.However,the addition of 0.5 wt.%Mn and 1.0 wt.%Mn to the T6-treated Al−Si−Mg alloys increased the size of theα-AlFeMnSi phase.This decreased the properties of T6-treated Al−Si−Mg alloys.Therefore,the optimum Mn content was 0.2 wt.%,providing a novel approach for synergistically enhancing mechanical properties and corrosion resistance of Al−Si−Mg alloys.展开更多
High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as not...High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as notable solid-state welding and processing techniques,have been proved effectiveness in enhancing microstructures and mechanical properties of HEAs.This review article summarizes the current status of FSW/P of HEAs.The welding materials and conditions used for FSW/P in HEAs are reviewed and discussed.The effects of FSW/P on the evolutions of grain structure,texture,dislocation,and secondary phase for different HEAs are highlighted.Furthermore,the influences of FSW/P on the mechanical properties of various HEAs are analyzed.Finally,potential applications,challenges,and future directions of FSW/P in HEAs are forecasted.Overall,FSW/P enable to refine grains of HEAs through dynamic recrystallization and to activate diverse deformation mechanisms of HEAs through tailoring phase structures,thereby significantly improving the strength,hardness,and ductility of both single-and dual-phase HEAs.Future progress in this field will rely on comprehensive optimization of processing parameters and alloy composition,integration of multi-scale modeling with advanced characterization for in-depth exploration of microstructural mechanisms,systematic evaluation of functional properties,and effective bridging of the gap between laboratory research and industrial application.The review aims to provide an overview of recent advancements in the FSW/P of HEAs and encourage further research in this area.展开更多
The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The micr...The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.展开更多
The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evo...The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.展开更多
The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solutio...The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.展开更多
The microstructures and mechanical properties of Al-8.3Zn-3.3Cu-2.2Mg alloys prepared via hot extrusion and liquid forging methods were investigated.Results show that based on DEFORM simulation analysis,the optimal ho...The microstructures and mechanical properties of Al-8.3Zn-3.3Cu-2.2Mg alloys prepared via hot extrusion and liquid forging methods were investigated.Results show that based on DEFORM simulation analysis,the optimal hot extrusion parameters are determined as ingot initial temperature of 380°C and extrusion speed of 3 mm/s.The hot-extruded aluminum alloy after T6 heat treatment presents superior mechanical properties with yield strength of 519.6 MPa,ultimate tensile strength of 582.1 MPa,and elongation of 11.0%.Compared with the properties of gravity-cast and liquid-forged alloys,the yield strength of hot-extruded alloy increases by 30.8%and 4.9%,and the ultimate tensile strength improves by 43.5%and 10.2%,respectively.The significant improvement in tensile strength of the hot-extruded alloys is attributed to the elimination of casting defects and the refinement of matrix grain and eutectic phases.In addition,the hot-extruded alloy demonstrates superior plasticity compared with the liquid-forged alloy.This is because severe plastic deformation occurs during hot extrusion,which effectively breaks and disperses the eutectic phases,facilitating the dissolution and precipitation of the second phases and inhibiting the microcrack initiation.展开更多
Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of L...Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of LIBs towards higher energy densities and the increasing density of electronic components on circuits,copper foil is required to have demanding properties,such as extremely thin thickness and extremely high tensile strength.This comprehensive review firstly summarizes recent progress on the fabrication of electrolytic copper foil,and the effects of process parameters,cathode substrate,and additives on the electrodeposition behavior,microstructure,and properties of copper foil are discussed in detail.Then the regulation strategies of mechanical properties of electrolytic copper foil are also summarized,including the formation of nanotwins and texture.Furthermore,the recent advances in novel electrolytic copper foils,such as composite foils and extra-thin copper foils,are also overviewed.Lastly,the remaining challenges and perspectives on the further development of electrolytic copper foils are presented.展开更多
Hot isostatic pressing (HIP) temperature has a significant impact on the service performance of powder metallurgy titanium alloys. In this study, a high-temperature titanium alloy, Ti-6.5Al-3.5Mo-1.5Zr-0.3Si, was prep...Hot isostatic pressing (HIP) temperature has a significant impact on the service performance of powder metallurgy titanium alloys. In this study, a high-temperature titanium alloy, Ti-6.5Al-3.5Mo-1.5Zr-0.3Si, was prepared under different HIP temperatures (880–1000℃), and the microstructural evolution and mechanical properties were systematically investigated. The results demonstrated that the HIPed alloys were predominantly composed of more than 80 vol.% α phase and a small amount of β phase, and their phase compositions were basically unaffected by the HIP temperatures. Under the typical single-temperature-maintained HIP (STM-HIP) regime, the microstructure of alloy significantly coarsened as the HIP temperature increased, and the alloy strength exhibited an obvious linear negative correlation with the HIP temperature. On the basis of Hall–Petch relation, the prediction model of grain size was established, and the mathematical equation between HIP temperature and grain size (d=M(T_(HIP-N)^(-2))) was deduced. Furthermore, a possible evolution mechanism of microstructure was proposed, which could be divided into the decomposition of initial α′ martensite for as-received powder, formation of the globular α grains in prior particle boundaries (PPBs) region, and precipitation of the platelet α grains in non-PPBs region. For these alloys prepared by the dual-temperature-maintained HIP (DTM-HIP) regime, although their tensile properties were comparable to that of alloy prepared by STM-HIP regime with same high-temperature holding stage, higher proportion of globular α grains occurred due to more recrystallization nucleation during the low-temperature holding stage, which probably provided a solution for improving the dynamic service performance of HIPed alloys.展开更多
Refractory high/medium-entropy alloys(RH/MEAs)are known for their outstanding performance at el-evated temperatures;however,they usually exhibit poor room-temperature plasticity,which can be at-tributed to the non-uni...Refractory high/medium-entropy alloys(RH/MEAs)are known for their outstanding performance at el-evated temperatures;however,they usually exhibit poor room-temperature plasticity,which can be at-tributed to the non-uniform deformation that occurs at room temperature.Once cracks nucleate,they will rapidly propagate into vertical splitting cracks.Here,we introduce multiple phases including FCC and HCP phases into the NbMoTa RMEA via appropriate addition of carbon.The results show that multiple-phase synergy effectively suppresses non-uniform deformation,thereby delaying the onset of vertical splitting cracks.An optimal combination of compressive strength-plasticity is achieved by the(NbMoTa)_(92.5)C_(7.5) alloy.The significant improvement in room-temperature mechanical properties can be attributed to its hierarchical microstructure:in the mesoscale,the BCC matrix is divided by eutectic structures;while at the microscale,the BCC matrix is further refined by abundant lath-like FCC precipitates.The FCC precip-itates contain high-density stacking faults,acting as a dislocation source under compressive loading.The HCP phase in the eutectic microstructures,in turn,acts as a strong barrier to dislocation movement and simultaneously increases the dislocation storage capacity.These findings open a new route to tailor the microstructure and mechanical properties of RH/MEAs.展开更多
This article studies the effects of different Sn contents on the melting characteristics,microstructure,and mechanical properties of brazed joints of low-silver BAg5CuZn-0.3 wt.%La brazing material.A differential ther...This article studies the effects of different Sn contents on the melting characteristics,microstructure,and mechanical properties of brazed joints of low-silver BAg5CuZn-0.3 wt.%La brazing material.A differential thermal analyzer(HCR-1)was used to measure the solid-liquidus temperature of BAg5CuZn-0.3 wt.%La-xSn brazing material.The results show that the addition of Sn element effect-ively reduces the solid-liquidus temperature of BAg5CuZn-0.3 wt.%La brazing material.Microstructural characterization was con-ducted using scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),X-ray diffraction(XRD),etc.Analysis re-veals that progressive aggregation and precipitation of Cu-Sn intermetallic compounds occur with increasing Sn content,leading to microstructural coarsening.Notably,severe grain coarsening is observed when the Sn content reaches 4 wt.%.Shear testing of the BAg5CuZn-0.3 wt.%La-xSn brazing joints reveals a non-monotonic trend in joint strength:as Sn content increases,the shear strength initially improves but subsequently deteriorates after reaching an optimal value.展开更多
The high-strength Mg-7Sn alloys(wt.%)with a heterogeneous grain structure were prepared by low-temperature extrusion(230°C)with the extrusion ratio of 9:1(9E230)and 17:1(17E230).The two extruded alloys contained ...The high-strength Mg-7Sn alloys(wt.%)with a heterogeneous grain structure were prepared by low-temperature extrusion(230°C)with the extrusion ratio of 9:1(9E230)and 17:1(17E230).The two extruded alloys contained fine dynamic recrystallization(DRX)grains(FG)and coarse un DRX grains(CG).The difference in deformability between CG and FG leads to the formation of heterogeneous grain structure.The average grain size and basal texture intensities increased while the volume fraction of CG decreased with increasing extrusion ratio.Tensile testing results indicated that the extruded 17E230 alloy exhibited higher tensile strengths than 9E230 alloy,whose tensile yield strength(σ_(0.2)),ultimate tensile strengths(σ_(b)),and elongation to failure(ε_(f))were 231.1 MPa,319.5MPa,and 12.54%respectively.The high tensile strengths of the extruded alloy mainly originated from grain refinement,texture strengthening,precipitation strengthening from a great number of nano-scale Mg_(2)Sn phases,solid solution strengthening and hetero-deformation induced(HDI)strengthening,while the good ductility of the alloy was also mainly attributed to grain refinement,activation of the non-basal slip systems and HDI hardening.展开更多
Thin walls of an AZ91 magnesium alloy with fine equiaxed grains were fabricated via cold arc-based wire arc additive manufacturing(CA-WAAM),and the droplet transfer behaviours,microstructures,and mechanical properties...Thin walls of an AZ91 magnesium alloy with fine equiaxed grains were fabricated via cold arc-based wire arc additive manufacturing(CA-WAAM),and the droplet transfer behaviours,microstructures,and mechanical properties were investigated.The results showed that the cold arc process reduced splashing at the moment of liquid bridge breakage and effectively shortened the droplet transfer period.The microstructures of the deposited samples exhibited layered characteristics with alternating distributions of coarse and fine grains.During layer-by-layer deposition,the β-phase precipitated and grew preferentially along grain boundaries,while the fineη-Al_(8)Mn_(5)phase was dispersed in the α-Mg matrix.The mechanical properties of the CA-WAAM deposited sample showed isotropic characteristics.The ultimate tensile strength and elongation in the building direction(BD)were 282.7 MPa and 14.2%,respectively.The microhardness values of the deposited parts were relatively uniform,with an average value of HV 69.6.展开更多
The regulation of sintering temperature in spark plasma sintering enables the achievement of grain refinement,phase control,and performance enhancement in the preparation of AZ91D magnesium alloy.This study investigat...The regulation of sintering temperature in spark plasma sintering enables the achievement of grain refinement,phase control,and performance enhancement in the preparation of AZ91D magnesium alloy.This study investigates the influence of sintering temperature on microstructural evolution and mechanical properties of the AZ91D alloy.Microstructural analysis was conducted using scanning electron microscopy,electron backscatter diffraction,and X-ray diffraction.Microscopic structures and mechanical behaviors were examined through hardness and tensile tests.Elevated sintering temperatures resulted in reduced secondary phase content,leading to a decrease in mechanical performance.The alloy exhibited optimal mechanical properties at 320℃.The nanoparticle coarsening process and particle evolution during sintering were simulated using phase field methods.By optimizing the sintering temperature,precise control over microstructural and textural evolution can be achieved,facilitating the attainment of desired hardness levels and mechanical properties.展开更多
Low-oxygen TZM alloy(oxygen content of 0.03vol%)was subjected to solid-solution heat treatment at various temperatures followed by quenching.Results show that the tensile strength of the alloy gradually decreases with...Low-oxygen TZM alloy(oxygen content of 0.03vol%)was subjected to solid-solution heat treatment at various temperatures followed by quenching.Results show that the tensile strength of the alloy gradually decreases with the increase in solidsolution temperature,and the elongation first increases and then decreases.The the amount of nanoscale Ti-rich phases precipitated in low-oxygen TZM alloys gradually increases with the increase in solid-solution temperature.Special strip-shaped Ti-rich areas appear in the samples solidified at 1200 and 1300℃.The nanoscale Ti-rich phases ensure the uniform distribution of dislocations throughout TZM alloy,while significantly improving the plasticity of low-oxygen TZM alloy samples.展开更多
The microstructure,micro-hardness,and tensile properties of interface between hot isostatic pressing densified low alloy steel and Inconel 690 cladding were investigated during the aging process at 600℃.The results s...The microstructure,micro-hardness,and tensile properties of interface between hot isostatic pressing densified low alloy steel and Inconel 690 cladding were investigated during the aging process at 600℃.The results show that the interface region can be divided into four zones from base metal to deposited metal:carbon-depleted zone(CDZ),partial melting zone(PMZ),planar growth zone(PGZ),and brownish feature zone(BFZ).Dimensions of these zones do not significantly change during aging.However,type I carbides noticeably increase in size in the PMZ,and precipitates clearly occur in the PGZ.The main reason for their growth and occurrence is continuous carbon migration.The highest micro-hardness appears in the PGZ and BFZ regions,which is related to carbon accumulation and precipitates in these regions.Tensile failure occurs on the base metal side due to the high strength mismatch between these two materials.The CDZ,composed of only ferrite,has lower strength and fractures at the boundary between CDZ and base metal.The ultimate tensile strength decreases by only 50 MPa after aging for 1500 h,and the interface region maintains high strength without significant deformation.展开更多
基金financially and technically supported by the National Key Laboratory Foundation of Science and Technology on Materials under Shock and Impact,Beijing Institute of Technology,China(No.WDZC2024-1)。
文摘Cryogenic rolling impacts on microstructure and mechanical properties of spray-formed 7055(SF-7055)Al alloy were investigated.Results show that with the increase of the reduction from 20%to 80%,the grain of cryogenic rolled SF-7055 Al alloy is elongated to form a fiber texture.Numerous proliferating dislocations in the microstructure accumulate into dislocation walls and cells,and eventually form subgrains.These subgrain boundaries divide the original grain,thereby reducing the grain size.Under severe deformation conditions,they even enable the formation of nanograins.Meanwhile,the Cu-rich precipitates in the matrix are also broken and refined under the action of large rolling stress.In the process of cryogenic rolling,the tensile strength and hardness of SF-7055 Al alloy gradually increase,while the plasticity decreases.Moreover,the fracture morphology of cryogenic rolled SF-7055 Al alloy gradually transforms to the ductile and quasi-cleavage hybrid fracture characteristics with increased reduction.
基金the financial support by the Major Science and Technology Achievement Transformation Project in Heilongjiang Province(No.ZC2023SH0075)the National Natural Science Foundation of China(Nos.52425401,U2441255,52474377,and 52371015)+1 种基金the Young Elite Scientists Sponsorship·Program by CAST(No.2021QNRC001)the Henan Provincial Key Research and Development&Promotion Special Program(No.251111231400)。
文摘The microstructure of high Nb-TiAl alloys was optimized by the addition of a small amount of Ta elements to further improve their properties.A series of Ti46Al1.5Cr8Nb-xTa(x=0.2,0.4,0.6,0.8,1.0,at.%)alloys were prepared by vacuum arc melting.The microstructure,mechanical properties,and related influencing mechanisms were systematically investigated.The results indicate that the solidification microstructure of the Ti46Al1.5Cr8Nb-xTa alloys comprises theγ-TiAl phase,α_(2)-Ti_(3)Al phase,and B2 phase.As the Ta content increases from 0.2 at.%to 1.0 at.%,the content ofα_(2)phase and B2 phase increases,while theγphase content decreases.Among them,the B2 phase shows the most pronounced change,being significantly refined,with its content increasing from 12.49%to 21.91%.In addition,the average size of the lamellar colony decreases from 160.65 to 94.44μm.The addition of the Ta element shifts the solidification path toward lower aluminum concentrations,leading to changes in phase content.The tantalum-induced increase in the B2 phase and enhanced supercooling at the solidification front provide the basis for lamellar colony refinement.Compressive testing at room temperature reveals that the Ti46 Al1.5 Cr8 Nb0.4 Ta alloy exhibits optimal compressive properties,achieving a compressive strength of 2,434 MPa and a compressive strain of 33.1%.The improvement of its properties is attributed to a combination of lamellar colony refinement,solid solution strengthening resulting from the incorporation of Ta element,and a reduction in the c/a of theγphase.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
基金Funded by Natural Science Foundation of Guangxi(No.2025GXNSFBA069565)Guangxi Science and Technology Program(No.AD25069101)Guangxi Bagui Scholars Fund。
文摘Crushing waste coral concrete into recycled aggregates to create recycled coral aggregate concrete(RCAC)contributes to sustainable construction development on offshore islands and reefs.To investigate the impact of recycled coral aggregate on concrete properties,this study performed a comprehensive analysis of the physical properties of recycled coral aggregate and the basic mechanical properties and microstructure of RCAC.The test results indicate that,compared to coral debris,the crushing index of recycled coral aggregate was reduced by 9.4%,while porosity decreased by 33.5%.Furthermore,RCAC retained the early strength characteristics of coral concrete,with compressive strength and flexural strength exhibiting a notable increase as the water-cement ratio decreased.Under identical conditions,the compressive strength and flexural strength of RCAC were 12.7% and 2.5% higher than coral concrete's,respectively,with porosity correspondingly reduced from 3.13% to 5.11%.This enhancement could be attributed to the new mortar filling the recycled coral aggregate.Scanning electron microscopy(SEM)analysis revealed three distinct interface transition zones within RCAC,with the‘new mortar-old mortar’interface identified as the weakest.The above findings provided a reference for the sustainable use of coral concrete in constructing offshore islands.
基金supported by the National Natural Science Foundation of China(No.52271101)Suzhou Science and Technology Project,China(Nos.SYG202312,SJC2023005,SZS2023023)+1 种基金Nanjing Major Science and Technology Project,China(No.202309015)the Opening Project of Jiangsu Key Laboratory of Advanced Structural Materials and Application Technology,China(No.ASMA202305)。
文摘To investigate the aging mechanisms and elucidate the correlations between unstable microstructure and performance in biodegradable Zn alloys,the accelerated aging experiment was conducted on a high-performance wrought Zn−0.1Mg alloy by annealing at 200℃ for varying durations.The findings reveal that the tensile strength of the alloy rapidly and significantly declines with prolonged annealing time,decreasing from 383 MPa for the as-received alloy to 102 MPa for the alloy subjected to 1440 min of annealing.The primary factors contributing to this considerable reduction in strength are static recrystallization,grain coarsening,and dislocation annihilation.Initially,the ductility of the alloy shows fluctuations,ultimately experiencing a marked decrease after extended annealing.This decline is linked to the grain growth and heightened texture intensity,while the unusual increase in ductility observed between 30 and 120 min of annealing is likely due to the formation of twins.In addition,due to rapid grain growth and an increase in precipitates and twins,the corrosion resistance of the alloy in Hank’s solution has worsened,with the corrosion rate rising from 0.037 to 0.069 mm/a following 300 min of annealing.
基金supported by the National Key Research and Development Program of China(No.2022YFB3404202)the National Natural Science Foundation of China(No.52271103)the Jilin Scientific and Technological Development Program,China(Nos.20220301026GX,20210301041GX)。
文摘The impact of Mn addition on the microstructure,mechanical properties and corrosion behavior of T6-treated Al−Si−Mg−xMn(x=0.2−1.0 wt.%)alloys in a 3.5 wt.%NaCl solution was investigated.The results showed that adding 0.2 wt.%Mn to T6-treated Al−Si−Mg alloys enhanced the corrosion resistance by promoting the formation ofα-AlFeMnSi phase,characterized by smaller absolute Volta potential values compared to eutectic Si,β-AlFeSi andπ-AlFeMgSi phases.However,the addition of 0.5 wt.%Mn and 1.0 wt.%Mn to the T6-treated Al−Si−Mg alloys increased the size of theα-AlFeMnSi phase.This decreased the properties of T6-treated Al−Si−Mg alloys.Therefore,the optimum Mn content was 0.2 wt.%,providing a novel approach for synergistically enhancing mechanical properties and corrosion resistance of Al−Si−Mg alloys.
基金supported by National Natural Science Foundation of China(Grant No.52171032)Hebei Natural Science Foundation(Grant No.E2023501002)Fundamental Research Funds for the Central Universities(Grant No.2024GFYD003)。
文摘High entropy alloys(HEAs)have recently attracted significant attention due to their exceptional mechanical properties and potential applications across various fields.Friction stir welding and processing(FSW/P),as notable solid-state welding and processing techniques,have been proved effectiveness in enhancing microstructures and mechanical properties of HEAs.This review article summarizes the current status of FSW/P of HEAs.The welding materials and conditions used for FSW/P in HEAs are reviewed and discussed.The effects of FSW/P on the evolutions of grain structure,texture,dislocation,and secondary phase for different HEAs are highlighted.Furthermore,the influences of FSW/P on the mechanical properties of various HEAs are analyzed.Finally,potential applications,challenges,and future directions of FSW/P in HEAs are forecasted.Overall,FSW/P enable to refine grains of HEAs through dynamic recrystallization and to activate diverse deformation mechanisms of HEAs through tailoring phase structures,thereby significantly improving the strength,hardness,and ductility of both single-and dual-phase HEAs.Future progress in this field will rely on comprehensive optimization of processing parameters and alloy composition,integration of multi-scale modeling with advanced characterization for in-depth exploration of microstructural mechanisms,systematic evaluation of functional properties,and effective bridging of the gap between laboratory research and industrial application.The review aims to provide an overview of recent advancements in the FSW/P of HEAs and encourage further research in this area.
基金supported by the National Natural Science Foundation of China(No.51874368)。
文摘The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.
基金support of the Research and Development Program in Key Areas of Guangdong Province,China(No.2019B090907001)the Science and Technology Program of Guangdong Province,China(No.2014B010129002)the National Key R&D Program of China(No.2017YFB0305800)。
文摘The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.
基金Tianjin Municipal Natural Science Foundation(23JCYBJC00040)National Natural Science Foundation of China(52175369)。
文摘The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.
基金Natural Science Foundation of Shandong Province of China(ZR2023QE193)。
文摘The microstructures and mechanical properties of Al-8.3Zn-3.3Cu-2.2Mg alloys prepared via hot extrusion and liquid forging methods were investigated.Results show that based on DEFORM simulation analysis,the optimal hot extrusion parameters are determined as ingot initial temperature of 380°C and extrusion speed of 3 mm/s.The hot-extruded aluminum alloy after T6 heat treatment presents superior mechanical properties with yield strength of 519.6 MPa,ultimate tensile strength of 582.1 MPa,and elongation of 11.0%.Compared with the properties of gravity-cast and liquid-forged alloys,the yield strength of hot-extruded alloy increases by 30.8%and 4.9%,and the ultimate tensile strength improves by 43.5%and 10.2%,respectively.The significant improvement in tensile strength of the hot-extruded alloys is attributed to the elimination of casting defects and the refinement of matrix grain and eutectic phases.In addition,the hot-extruded alloy demonstrates superior plasticity compared with the liquid-forged alloy.This is because severe plastic deformation occurs during hot extrusion,which effectively breaks and disperses the eutectic phases,facilitating the dissolution and precipitation of the second phases and inhibiting the microcrack initiation.
基金supported by the National Key R&D Plan Program of China(No.2021YFB3400800)Henan Key Research and Development Program(No.231111241000)+1 种基金the Joint Fund of Henan Province Science and Technology R&D Program(No.225200810026)Zhongyuan Scholar Workstation Funded Program(No.224400510025).
文摘Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of LIBs towards higher energy densities and the increasing density of electronic components on circuits,copper foil is required to have demanding properties,such as extremely thin thickness and extremely high tensile strength.This comprehensive review firstly summarizes recent progress on the fabrication of electrolytic copper foil,and the effects of process parameters,cathode substrate,and additives on the electrodeposition behavior,microstructure,and properties of copper foil are discussed in detail.Then the regulation strategies of mechanical properties of electrolytic copper foil are also summarized,including the formation of nanotwins and texture.Furthermore,the recent advances in novel electrolytic copper foils,such as composite foils and extra-thin copper foils,are also overviewed.Lastly,the remaining challenges and perspectives on the further development of electrolytic copper foils are presented.
基金support from CAS Project for Young Scientists in Basic Research(YSBR-025)and the Technology Innovation(RCJJ-145-24-39)R.P.Guo acknowledges the financial support from the National Natural Science Foundation of China(No.52401104)+1 种基金the Fundamental Research Program of Shanxi Province(No.202203021221072)the China Postdoctoral Science Foundation(No.2024M753298).
文摘Hot isostatic pressing (HIP) temperature has a significant impact on the service performance of powder metallurgy titanium alloys. In this study, a high-temperature titanium alloy, Ti-6.5Al-3.5Mo-1.5Zr-0.3Si, was prepared under different HIP temperatures (880–1000℃), and the microstructural evolution and mechanical properties were systematically investigated. The results demonstrated that the HIPed alloys were predominantly composed of more than 80 vol.% α phase and a small amount of β phase, and their phase compositions were basically unaffected by the HIP temperatures. Under the typical single-temperature-maintained HIP (STM-HIP) regime, the microstructure of alloy significantly coarsened as the HIP temperature increased, and the alloy strength exhibited an obvious linear negative correlation with the HIP temperature. On the basis of Hall–Petch relation, the prediction model of grain size was established, and the mathematical equation between HIP temperature and grain size (d=M(T_(HIP-N)^(-2))) was deduced. Furthermore, a possible evolution mechanism of microstructure was proposed, which could be divided into the decomposition of initial α′ martensite for as-received powder, formation of the globular α grains in prior particle boundaries (PPBs) region, and precipitation of the platelet α grains in non-PPBs region. For these alloys prepared by the dual-temperature-maintained HIP (DTM-HIP) regime, although their tensile properties were comparable to that of alloy prepared by STM-HIP regime with same high-temperature holding stage, higher proportion of globular α grains occurred due to more recrystallization nucleation during the low-temperature holding stage, which probably provided a solution for improving the dynamic service performance of HIPed alloys.
基金financial support from the Na-tional Natural Science Foundation of China(No.52231006)National Key Research and Development Program of China(No.2017YFB0702003)the National Natural Science Foundation of China(No.51871217).
文摘Refractory high/medium-entropy alloys(RH/MEAs)are known for their outstanding performance at el-evated temperatures;however,they usually exhibit poor room-temperature plasticity,which can be at-tributed to the non-uniform deformation that occurs at room temperature.Once cracks nucleate,they will rapidly propagate into vertical splitting cracks.Here,we introduce multiple phases including FCC and HCP phases into the NbMoTa RMEA via appropriate addition of carbon.The results show that multiple-phase synergy effectively suppresses non-uniform deformation,thereby delaying the onset of vertical splitting cracks.An optimal combination of compressive strength-plasticity is achieved by the(NbMoTa)_(92.5)C_(7.5) alloy.The significant improvement in room-temperature mechanical properties can be attributed to its hierarchical microstructure:in the mesoscale,the BCC matrix is divided by eutectic structures;while at the microscale,the BCC matrix is further refined by abundant lath-like FCC precipitates.The FCC precip-itates contain high-density stacking faults,acting as a dislocation source under compressive loading.The HCP phase in the eutectic microstructures,in turn,acts as a strong barrier to dislocation movement and simultaneously increases the dislocation storage capacity.These findings open a new route to tailor the microstructure and mechanical properties of RH/MEAs.
基金the support from Jinhua Sanhuan Welding Materials Company LimitedSchool of Materials Science and Engineering,Nanjing University of Science and Technology.
文摘This article studies the effects of different Sn contents on the melting characteristics,microstructure,and mechanical properties of brazed joints of low-silver BAg5CuZn-0.3 wt.%La brazing material.A differential thermal analyzer(HCR-1)was used to measure the solid-liquidus temperature of BAg5CuZn-0.3 wt.%La-xSn brazing material.The results show that the addition of Sn element effect-ively reduces the solid-liquidus temperature of BAg5CuZn-0.3 wt.%La brazing material.Microstructural characterization was con-ducted using scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),X-ray diffraction(XRD),etc.Analysis re-veals that progressive aggregation and precipitation of Cu-Sn intermetallic compounds occur with increasing Sn content,leading to microstructural coarsening.Notably,severe grain coarsening is observed when the Sn content reaches 4 wt.%.Shear testing of the BAg5CuZn-0.3 wt.%La-xSn brazing joints reveals a non-monotonic trend in joint strength:as Sn content increases,the shear strength initially improves but subsequently deteriorates after reaching an optimal value.
基金supported by the Major Science and Technology Project of Gansu Province(Grant No.22ZD6GA008)the National Natural Science Foundation of China(Nos.52261027,52001152 and 51961021)+2 种基金the Open Project of State Key Laboratory for Mechanical Behavior of Materials(20192102)Undergraduate Innovation and Entrepreneurship Training Program(Nos.DC20231482,DC20231188 and DC20231558)Gansu Provincial Excellent Graduate Students“Innovation Star”Program(2022CXZX-394)。
文摘The high-strength Mg-7Sn alloys(wt.%)with a heterogeneous grain structure were prepared by low-temperature extrusion(230°C)with the extrusion ratio of 9:1(9E230)and 17:1(17E230).The two extruded alloys contained fine dynamic recrystallization(DRX)grains(FG)and coarse un DRX grains(CG).The difference in deformability between CG and FG leads to the formation of heterogeneous grain structure.The average grain size and basal texture intensities increased while the volume fraction of CG decreased with increasing extrusion ratio.Tensile testing results indicated that the extruded 17E230 alloy exhibited higher tensile strengths than 9E230 alloy,whose tensile yield strength(σ_(0.2)),ultimate tensile strengths(σ_(b)),and elongation to failure(ε_(f))were 231.1 MPa,319.5MPa,and 12.54%respectively.The high tensile strengths of the extruded alloy mainly originated from grain refinement,texture strengthening,precipitation strengthening from a great number of nano-scale Mg_(2)Sn phases,solid solution strengthening and hetero-deformation induced(HDI)strengthening,while the good ductility of the alloy was also mainly attributed to grain refinement,activation of the non-basal slip systems and HDI hardening.
基金supported by the National Natural Science Foundation of China(No.51805265)the Fundamental Research Funds for the Central Universities,China(No.30922010921).
文摘Thin walls of an AZ91 magnesium alloy with fine equiaxed grains were fabricated via cold arc-based wire arc additive manufacturing(CA-WAAM),and the droplet transfer behaviours,microstructures,and mechanical properties were investigated.The results showed that the cold arc process reduced splashing at the moment of liquid bridge breakage and effectively shortened the droplet transfer period.The microstructures of the deposited samples exhibited layered characteristics with alternating distributions of coarse and fine grains.During layer-by-layer deposition,the β-phase precipitated and grew preferentially along grain boundaries,while the fineη-Al_(8)Mn_(5)phase was dispersed in the α-Mg matrix.The mechanical properties of the CA-WAAM deposited sample showed isotropic characteristics.The ultimate tensile strength and elongation in the building direction(BD)were 282.7 MPa and 14.2%,respectively.The microhardness values of the deposited parts were relatively uniform,with an average value of HV 69.6.
基金supported by the National Natural Science Foundation of China(Nos.52074246,22008224,52275390,52205429,52201146)National Defense Basic Scientific Research Program of China(Nos.JCKY2020408B002,WDZC2022-12)+2 种基金Key Research and Development Program of Shanxi Province(202102050201011,2022ZDYF035)Science and Technology Major Project of Shanxi Province(20191102008,20191102007)Guiding Local Science and Technology Development Projects by the Central Government(YDZJSX2022A025,YDZJSX2021A027).
文摘The regulation of sintering temperature in spark plasma sintering enables the achievement of grain refinement,phase control,and performance enhancement in the preparation of AZ91D magnesium alloy.This study investigates the influence of sintering temperature on microstructural evolution and mechanical properties of the AZ91D alloy.Microstructural analysis was conducted using scanning electron microscopy,electron backscatter diffraction,and X-ray diffraction.Microscopic structures and mechanical behaviors were examined through hardness and tensile tests.Elevated sintering temperatures resulted in reduced secondary phase content,leading to a decrease in mechanical performance.The alloy exhibited optimal mechanical properties at 320℃.The nanoparticle coarsening process and particle evolution during sintering were simulated using phase field methods.By optimizing the sintering temperature,precise control over microstructural and textural evolution can be achieved,facilitating the attainment of desired hardness levels and mechanical properties.
基金Outstanding Doctorate Dissertation Cultivation Fund of Xi'an University of Architecture and Technology(160842012)National Natural Science Foundation of China(52404409,52374401,52104382)+3 种基金China Postdoctoral Science Foundation(2024MD753961)Scientific and Technological Innovation Team Project of Shaanxi Innovation Capability Support Plan(2022TD-30)Key R&D Plan of Shaanxi Province(2023JBGS-14,2024QCYKXJ-116)Xi'an Science and Technology Plan Project(24ZDCYJSGG0043,2023JH-GXRC-0020)。
文摘Low-oxygen TZM alloy(oxygen content of 0.03vol%)was subjected to solid-solution heat treatment at various temperatures followed by quenching.Results show that the tensile strength of the alloy gradually decreases with the increase in solidsolution temperature,and the elongation first increases and then decreases.The the amount of nanoscale Ti-rich phases precipitated in low-oxygen TZM alloys gradually increases with the increase in solid-solution temperature.Special strip-shaped Ti-rich areas appear in the samples solidified at 1200 and 1300℃.The nanoscale Ti-rich phases ensure the uniform distribution of dislocations throughout TZM alloy,while significantly improving the plasticity of low-oxygen TZM alloy samples.
基金Major Scientific and Technological Project of Gansu(22ZD6GA008)Excellent Doctorate Project of Gansu(23JRRA806)National Natural Science Foundation of China(52175325,51961024,52071170)。
文摘The microstructure,micro-hardness,and tensile properties of interface between hot isostatic pressing densified low alloy steel and Inconel 690 cladding were investigated during the aging process at 600℃.The results show that the interface region can be divided into four zones from base metal to deposited metal:carbon-depleted zone(CDZ),partial melting zone(PMZ),planar growth zone(PGZ),and brownish feature zone(BFZ).Dimensions of these zones do not significantly change during aging.However,type I carbides noticeably increase in size in the PMZ,and precipitates clearly occur in the PGZ.The main reason for their growth and occurrence is continuous carbon migration.The highest micro-hardness appears in the PGZ and BFZ regions,which is related to carbon accumulation and precipitates in these regions.Tensile failure occurs on the base metal side due to the high strength mismatch between these two materials.The CDZ,composed of only ferrite,has lower strength and fractures at the boundary between CDZ and base metal.The ultimate tensile strength decreases by only 50 MPa after aging for 1500 h,and the interface region maintains high strength without significant deformation.
