This work proposed a strategy of indirectly inducing uniform microarc discharge by controlling the content and distribution ofβ-Mg_(17)Al_(12)phase in AZ91D Mg alloy.Two kinds of nano-particles(ZrO_(2)and TiO_(2))wer...This work proposed a strategy of indirectly inducing uniform microarc discharge by controlling the content and distribution ofβ-Mg_(17)Al_(12)phase in AZ91D Mg alloy.Two kinds of nano-particles(ZrO_(2)and TiO_(2))were designed to be added into the substrate of Mg alloy by friction stir processing(FSP).Then,Mg alloy sample designed with different precipitated morphology ofβ-Mg_(17)Al_(12)phase was treated by microarc oxidation(MAO)in Na_(3)PO_(4)/Na2SiO3electrolyte.The characteristics and performance of the MAO coating was analyzed using scanning electron microscopy(SEM),energy dispersive spectrometer(EDS),X-ray diffraction(XRD),X-ray photoelectron spectroscopy(XPS),contact angle meter,and potentiodynamic polarization.It was found that the coarseα-Mg grains in extruded AZ91D Mg alloy were refined by FSP,and theβ-Mg_(17)Al_(12)phase with reticular structure was broken and dispersed.The nano-ZrO_(2)particles were pinned at the grain boundary by FSP,which refined theα-Mg grain and promoted the precipitation ofβ-Mg_(17)Al_(12)phase in grains.It effectively inhibited the“cascade”phenomenon of microarcs,which induced the uniform distribution of discharge pores.The MAO coating on Zr-FSP sample had good wettability and corrosion resistance.However,TiO_(2)particles were hardly detected in the coating on TiFSP sample.展开更多
The combined microarc oxidation （MAO） and magnetron sputtering deposition process was used to deposit duplex a-C：H/MAO and Ti-a-C：H/MAO coatings on AM80 magnesium alloy. The microstructure, mechanical properties a...The combined microarc oxidation （MAO） and magnetron sputtering deposition process was used to deposit duplex a-C：H/MAO and Ti-a-C：H/MAO coatings on AM80 magnesium alloy. The microstructure, mechanical properties and tribological behavior of the two duplex coatings were investigated. The experimental results showed that the a-C：H and Ti-a-C：H top films on Si substrates were dense and had a low G peak position and ID/IG ratio, compared with the hydrogen-free amorphous carbon films. Numerous micropores were found on the duplex a-C：H/MAO and Ti-a-C：H/MAO coatings together with low values of hardness （H） and elastic modulus （E）, which also showed good binding strength with the Mg alloy substrates. Compared to MAO treated substrate used for the protection of the Mg alloy, the duplex a-C：H/MAO and Ti-a- C：H/MAO coatings still had stable and low value of friction coefficient, even though the surface of the duplex coatings was rough and porous. Furthermore, the mechanism of friction reduction of the two duplex coatings on the Mg alloy substrates was discussed.展开更多
Nano-zinc oxides(ZnO)demonstrate remarkable antibacterial properties.To further enhance the corrosion resistance and antibacterial efficiency of magnesium alloy micro-arc oxidation(MAO)coatings,this study investigates...Nano-zinc oxides(ZnO)demonstrate remarkable antibacterial properties.To further enhance the corrosion resistance and antibacterial efficiency of magnesium alloy micro-arc oxidation(MAO)coatings,this study investigates the preparation of ZnO-containing micro-arc oxidation coatings with dual functionality by incorporating nano-ZnO into MAO electrolyte.The influence of varying ZnO concentrations on the microstructure,corrosion resistance,and antibacterial properties of the coating was examined through microstructure analysis,immersion tests,electrochemical experiments,and antibacterial assays.The findings revealed that the addition of nano-ZnO significantly enhanced the corrosion resistance of the MAO-coated alloy.Specifically,when the ZnO concentration in the electrolyte was 5 g/L,the corrosion rate was more than ten times lower compared to the MAO coatings without ZnO.Moreover,the antibacterial efficacy of ZnO+MAO coating,prepared with a ZnO concentration of 5 g/L,surpassed 95%after 24 h of co-culturing with Staphylococcus aureus(S.aureus).The nano-ZnO+MAO-coated alloy exhibited exceptional degradation resistance,corrosion resistance,and antibacterial effectiveness.展开更多
Micro-arc oxidation(MAO)flm can only provide common mechanical protection for magnesium(Mg)–lithium(Li)alloys.These alloys are susceptible to severe localized corrosion,if the MAO flm is disrupted.This work reports t...Micro-arc oxidation(MAO)flm can only provide common mechanical protection for magnesium(Mg)–lithium(Li)alloys.These alloys are susceptible to severe localized corrosion,if the MAO flm is disrupted.This work reports the successful hydrothermal preparation of a MgLiAlCe-LDHs@GO flm on a MAO-coated Mg–Li alloy following Ce confnement.The graphene oxide(GO)sheet increased the difusion path of the corrosive media,and the addition of rare-earth cerium ions(Ce^(3+))endowed the flm with a certain self-healing ability,which signifcantly improved the corrosion resistance of the flm,and the corrosion current density(icorr)reached 3.27×10^(−8)A cm^(−2).The synergistic action of GO and Ce^(3+)can achieve long-term corrosion protection for the substrate.The corrosion resistance mechanism of MgLiAlCe-LDHs@GO flm was discussed by the scanning vibration electrode technique(SVET).展开更多
The microarc oxidation（MAO） coatings produced at different current frequencies on AZ91 D magnesium alloys were studied systematically. The morphologies, thickness, corrosion performances, and tribological properties...The microarc oxidation（MAO） coatings produced at different current frequencies on AZ91 D magnesium alloys were studied systematically. The morphologies, thickness, corrosion performances, and tribological properties of the coatings were investigated by the scanning electron microscopy, the electrochemical measurement system, and MS-T3000 friction test rig, respectively. The results show that the structure of the coatings becomes denser, and thickness becomes thinner with the increase of the current frequency. It is also found that the corrosion resistance of the coatings produced at higher frequency is improved greatly and the difference of the corrosion current density becomes small with increasing current frequency, which is similar to that of the coating thickness. The tribological test shows that the friction coefficient decreases with increasing the current frequency and the wear resistance of the coatings is influenced by both the thickness and structures. All these results were explained by analyzing the growing process of the MAO coating.展开更多
Microarc oxidation （MAO） process was conducted on AZ91D magnesium alloy in an electrolyte composed of NazSiO3, NaAlO2, NaEB4O7, NaOH, C3H803 and C6H5Na307 by AC pulse electrical source. The surface and cross-section...Microarc oxidation （MAO） process was conducted on AZ91D magnesium alloy in an electrolyte composed of NazSiO3, NaAlO2, NaEB4O7, NaOH, C3H803 and C6H5Na307 by AC pulse electrical source. The surface and cross-sectional morphologies, film thickness, chemical composition and structure of the coatings were characterized by scanning electron microscopy（SEM）, layer thickness metry, energy disperse spectroscopy（EDS） and X-ray diffraction（XRD）. The corrosiofi resistances of the coatings in a 3.5% NaC1 neutral solution were evaluated by electrochemical impedance spectroscopy （EIS） and potentiodynamic polarization test. The results showed that an optimized electrolyte with a composition of 15 g/L NazSiO3, 9 g/L NaA102, 2 g/L NazB407, 3 g/L NaOH, 5 mL/L C3H803 and 7 g/LC,HsNa307 was developed by means of orthogonal experiment. The coating obtained in the optimized electrolyte had a dense structure and revealed a lower current density, decreased by two orders of magnitude as compared with the magnesium substrate. Meanwhile, the corrosive potentials of the coated samples increased nearly by 73 inV. EIS result showed that the corrosion resistance of the coating was mainly determined by the inner dense layer. The coating primarily contained elements Mg, Al, O and Si and XRD analyses indicated that the coating was mainly composed of MgO, Mg2SiO4 and MgAl204.展开更多
The effects of rare earths on the properties of the microarc oxidation（MAO） coating on a magnesium alloy were investigated by means of scanning electron microscopy（SEM）,energy dispersive X-ray spectroscopy（EDS）,...The effects of rare earths on the properties of the microarc oxidation（MAO） coating on a magnesium alloy were investigated by means of scanning electron microscopy（SEM）,energy dispersive X-ray spectroscopy（EDS）,and electrochemistry methods.The results show that a nice and compact MAO coating was successfully obtained when the magnesium alloy was treated in nitrate solutions as the pre-treatment of MAO.However,the MAO was not successfully completed for the silicate electrolytes with the addition of rare earths.After the magnesium alloy being treated by rare earth nitrate,the obtained MAO coating has advantages such as uniform distribution of thickness,improved corrosion resistance,and nice-uniform surface,as compared with the untreated magnesium alloy.In addition,the time of non-ESP,the voltage and current density of the MAO process obviously decrease.Cerium oxide doped on the surface of the magnesium alloy can significantly improve the corrosion resistance of the MAO coating and decrease the current density of the MAO process,as compared with lanthanum oxide,whereas the doped rare earths have no significant effect on the components of the MAO coating.展开更多
Zirconia coatings as hydrogen permeation barriers were formed on disktype ZrHj.s substrate speci mens in phosphate solution system by microarc oxidation technique. Influence of positive voltage on hydrogen per meation...Zirconia coatings as hydrogen permeation barriers were formed on disktype ZrHj.s substrate speci mens in phosphate solution system by microarc oxidation technique. Influence of positive voltage on hydrogen per meation barriers on the surface of zirconium hydride was investigated as the main factor. The thickness of total oxide layer increased from 42.5 to 55.0 ~tm the increase of positive voltage increasing from 325 up to 425 V. The permeation reduction factor （PRF） was observed under different voltages, which increased with the increasing positive voltages. The phase structure of oxide layer was monoclinic Zr02 and tetragonal ZrO1.88. No reduction reaction occured in the process of hydrogen escaping, and it indicates that hydrogen permeation through oxide layer is restricted.展开更多
Selective growth of oxidation coating was observed with Al18B4O33 crystal whisker as reinforced phase） on Mg matrix composite Al18B4O33w/AZ91 （a composite when this composite was treated by microarc oxidation （MAO...Selective growth of oxidation coating was observed with Al18B4O33 crystal whisker as reinforced phase） on Mg matrix composite Al18B4O33w/AZ91 （a composite when this composite was treated by microarc oxidation （MAO） technique, and then the role of Al18B4O33 whisker in the process of MAO was analyzed. The protective properties of MAO coating also were investigated. Scanning electron microscopy （SEM） was used to characterize the existing state of Al18B4O33 whisker in MAO process and the microstructure of MAO coating. Corrosion resistance of the bare and coated composite was evaluated by immersion corrosion test and potentiodynamic polarizing test. Wear resistance of MAO coating was investigated by a ball-on-disc friction and wear tester. The results showed that sparking discharge did not occur on Al18B4O33 whisker and the whisker existed in the coating as a heterogeneous phase when MAO coating grew on the composite; then the whisker would be covered gradually with growing thick of the coating. Corrosion current density of the coated composite was decreased by 4 orders of magnitude compared with that of the uncoated composite; excellent corrosion resistance was closely related to the compact whisker-coating interface since Al18B4O33 whisker did not induce structural defects. The coating also exhibited high wear resistance and a slight adhesive wear tendency with bearing steel as its counterpart material.展开更多
Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the su...Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the surface ofpure titanium by alternating-current microarc discharge in aluminate solution were investigated byX-ray diffraction and scanning electron microscopy. The profiles of the hardness H and the elasticmodulus E in the coatings were determined using a nanoindentation method. The concentrationdistributions of Ti, Al, and O in the coating show that this coating over 30 mu m thick contains twolayers: an outer layer and an inner layer. The oxide coating is mainly composed of TiO_2 rutile andAl_2TiO_5 compounds. During oxidation, the temperature in the microarc discharge channel was veryhigh to make the local coating molten. From the surface to the interior of the coating, H and Eincrease gradually, and then reach maximum values of 9.78 GPa and 176 GPa respectively at a distanceof 7 mu m from the coating/titanium interface. They are also rather high near the interface.展开更多
In this work, microarc oxidation(MAO) technology was used to form oxide ceramic coating on the surface of aluminum alloy. The combined additives nano-TiOand nano-ZnO were added into the silicate electrolyte, and the e...In this work, microarc oxidation(MAO) technology was used to form oxide ceramic coating on the surface of aluminum alloy. The combined additives nano-TiOand nano-ZnO were added into the silicate electrolyte, and the effect of the compound nano-additive on microstructure and properties of MAO coating was investigated. The results show that compared with those of the nano-additive-free coating formed on aluminum alloy, the thickness, hardness, abrasion resistance and corrosion resistance of the nano-additive-containing coating are obviously improved. The surface of coating with nanoadditive becomes smooth, dense, and there are less porosities and microcracks. Moreover, the content of crystal phase a-AlOand y-AlOincreases visibly on the nano-additive-containing MAO coatings, and new phases AlTi and ZnTiare detected in the coatings, which are mainly contributed to the excellent corrosion resistance and abrasion resistance of the film. When the contents of nano-TiOand nano-ZnO are, respectively, 4 and 2 g-L, the film has better comprehensive performance, the thickness and hardness of the film could reach 52 μm and HV 692,respectively.展开更多
Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation（MAO） in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings...Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation（MAO） in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings were studied by XRD and SEM,respectively.The growing mechanism of ceramic coatings was discussed in a preliminary manner.The results show that with an increase in MAO time,the compactness of the coating improved and the thickness increased.From the inner layer to the coating surface,the content of Zr increased,while the content of Al decreased.In addition,the coating was composed of m-ZrO2,t-ZrO2,and a little amount of γ-Al2O3.With an increase in reaction time,the relative content of t-ZrO2 within the coating sharply decreased while the relative content of m-ZrO2 sharply increased,and then both generally kept at a constant level after 60 min.展开更多
Selective growth of oxidation coating was observed on Mg alloy AZ91 D when this alloy was treated by microarc oxidation （MAO） technique, and then the role of intermetallic phase Mg17AI12 （β phase） during MAO was ...Selective growth of oxidation coating was observed on Mg alloy AZ91 D when this alloy was treated by microarc oxidation （MAO） technique, and then the role of intermetallic phase Mg17AI12 （β phase） during MAO was investigated. Corrosion resistance and anti-corrosion mechanism of the MAO coating were also studied. Optical microscopy and scanning electron microscopy （SEM） were used to characterize β phase and coating microstructure. Corrosion properties of the coated alloy were studied by potentiodynamic polarization test and electrochemical impedance spectroscopy （EIS） in 3.5% NaCI solution. Results showed that sparking discharge preferentially occurred on ^-Mg phase rather than on β phase at the early stage of MAO; however selective growth of the coating disappeared gradually with the increasing oxidation time and β phase would not further inhibit coating growth at the prolonged stage of MAO. MglTAI12 phase ultimately was unable to destroy the integrity and continuity of MAO coating. The MAO coating could restrain charge transfer process and then greatly enhance corrosion resistance of AZ91D alloy. Sealing treatment of MAO coating by stearic acid could further improve the corrosion resistance of AZ91 D alloy.展开更多
The combined microarc oxidation (MAO) and inorganic sealing process was used to deposit a composite coating to improve the corrosion resistance of AZ31 magnesium alloy.The surface morphologies of the resulting duplex ...The combined microarc oxidation (MAO) and inorganic sealing process was used to deposit a composite coating to improve the corrosion resistance of AZ31 magnesium alloy.The surface morphologies of the resulting duplex coatings were studied by SEM.Furthermore,the corrosion resistance of the coated Mg alloy substrates was investigated using electrochemical workstation and dropping corrosion test.The results show that the composite coating surface consists of Mg,Si,O and Na.It is difficult to deposit inorganic coating on a thick MAO coating surface.As the composite coating was solidified by CO2 under 175 °C,it exhibits a better corrosion resistance than the MAO monolayer,owing to the thick and compact inorganic coating.展开更多
Dense ceramic oxide coatings of about 50 μm may be prepared on Ti-6AI-4V alloy surface by alternating-current microarc oxidation in aluminate and silicate solutions, respectively. Their phase constituent and microstr...Dense ceramic oxide coatings of about 50 μm may be prepared on Ti-6AI-4V alloy surface by alternating-current microarc oxidation in aluminate and silicate solutions, respectively. Their phase constituent and microstructure were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the electrolytic ions have incorporated into the interior of the coatings. The coating formed in aluminate solution is composed of the rutile TiO2 and TiAl2O5 phases rather than the rutile, anatase and amorphous SiO2 phases for the coating formed in silicate solution. However, TiAl2O5 content in the outer layer of the two coatings is much higher than in the inner layer. It is suggested that all these oxides may result from a rapid solidification of the molten coating in the microarc discharge zone.展开更多
A reliable,high-performance coating procedure was developed using PDMS to modify a duplex MAO/DLC coating on an AZ31B Mg alloy.First,the duplex MAO/DLC coating was fabricated via a combined MAO and unbalanced magnetro...A reliable,high-performance coating procedure was developed using PDMS to modify a duplex MAO/DLC coating on an AZ31B Mg alloy.First,the duplex MAO/DLC coating was fabricated via a combined MAO and unbalanced magnetron sputter process.Subsequently,a PDMS solution was used to modify the MAO/DLC coating via a conventional dip-coating method.The surface characteristics,bond strength,hardness,tribological behaviour,and corrosion resistance of the coated samples were evaluated via SEM,CA,Raman spectroscopy,friction and wear behaviour,polarisation curve,and NSS tests.The PDMS modification reduced the HIT of MAO/DLC coating from 15.96 to 8.34GPa;this is ascribed to the penetration of PDMS,which has good rheological properties to form a viscoelastic Si-based organic polymer layer on the MAO/DLC coating.However,the PDMS-modified MAO/DLC coating was denser,hydrophobic,and had higher bond strength compared with MAO-and MAO/DLC-coated samples.Moreover,the PDMS modification reduced the COF and wear rate of the duplex MAO/DLC coating.This indicates that the PDMS improved the tribological behaviour owing to the transferred Si oxide that originated from the Si-O network of the PDMS,as well as the low graphitisation of the DLC layer during sliding.Furthermore,the corrosion current density of the MAO/DLC-coated sample modified by PDMS for 10min decreased by two order of magnitude compared with that of the MAO/DLC-coated sample but by five orders of magnitude compared with that of the bare substrate.The NSS tests proved that the PDMS layer slowed the corrosion of the Mg alloy under long-term service,enhancing the corrosion protection efficiency.The results are attributed to the high bond strength and lubricant MAO/DLC layer,and the dual role of sealing and hydrophobicity of PDMS.Therefore,PDMS modification is promising for the fabrication of protective materials for Mg alloys that require corrosion and wear resistance.展开更多
Microarc oxidation(MAO)is an effective surface treatment method for Ti alloys to allow their application in extreme environments.Here,binary electrolytes consisting of different amounts of sodium phosphate and sodium ...Microarc oxidation(MAO)is an effective surface treatment method for Ti alloys to allow their application in extreme environments.Here,binary electrolytes consisting of different amounts of sodium phosphate and sodium silicate were designed for MAO.The surface morphology,composition,and properties of MAO coatings on Ti-6Al-4V alloy treated in 0.10 mol/L electrolyte were investigated to reveal the effect of PO_(4)^(3-)and SiO_(3)^(2-)ray diffraction,and potentiodynamic polarization.The results showed that PO_(4)^(3-)is beneficial for generating microarcs and forming pores within the coating,resulting in a thick but porous coating.SiO_(3)^(2-)eration of microarcs,resulting in a thin dense coating.The thickness,density,phases content,and polarization resistance of the MAO coatings are primarily affected by the intensity of microarcs for low SiO_(3)^(2-)ciently high.The thickness of MAO coatings obtained in P/Si electrolytes shows a piecewise linear increase with increasing process time during the three stages of microarc discharge.SiO_(3)^(2-)discharge,but slows down the growth of the coating formed in the next stage.展开更多
In this work, the morphology, phase composition, and corrosion properties of microarc oxidized (MAO) gas tungsten arc (GTA) weldments of AZ31 alloy were investigated. Autogenous gas tungsten arc welds were made as ful...In this work, the morphology, phase composition, and corrosion properties of microarc oxidized (MAO) gas tungsten arc (GTA) weldments of AZ31 alloy were investigated. Autogenous gas tungsten arc welds were made as full penetration bead-on-plate welding under the alternating-current mode. A uniform oxide layer was developed on the surface of the specimens with MAO treatment in silicate-based alkaline electrolytes for different oxidation times. The corrosion behavior of the samples was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy. The oxide film improved the corrosion resistance substantially compared to the uncoated specimens. The sample coated for 10 min exhibited better corrosion properties. The corrosion resistance of the coatings was concluded to strongly depend on the morphology, whereas the phase composition and thickness were concluded to only slightly affect the corrosion resistance.展开更多
基金funded by China Postdoctoral Science Foundation(No.2021M700569)Chongqing Postdoctoral Science Foundation(No.7 cstc2021jcyj-bshX0087)。
文摘This work proposed a strategy of indirectly inducing uniform microarc discharge by controlling the content and distribution ofβ-Mg_(17)Al_(12)phase in AZ91D Mg alloy.Two kinds of nano-particles(ZrO_(2)and TiO_(2))were designed to be added into the substrate of Mg alloy by friction stir processing(FSP).Then,Mg alloy sample designed with different precipitated morphology ofβ-Mg_(17)Al_(12)phase was treated by microarc oxidation(MAO)in Na_(3)PO_(4)/Na2SiO3electrolyte.The characteristics and performance of the MAO coating was analyzed using scanning electron microscopy(SEM),energy dispersive spectrometer(EDS),X-ray diffraction(XRD),X-ray photoelectron spectroscopy(XPS),contact angle meter,and potentiodynamic polarization.It was found that the coarseα-Mg grains in extruded AZ91D Mg alloy were refined by FSP,and theβ-Mg_(17)Al_(12)phase with reticular structure was broken and dispersed.The nano-ZrO_(2)particles were pinned at the grain boundary by FSP,which refined theα-Mg grain and promoted the precipitation ofβ-Mg_(17)Al_(12)phase in grains.It effectively inhibited the“cascade”phenomenon of microarcs,which induced the uniform distribution of discharge pores.The MAO coating on Zr-FSP sample had good wettability and corrosion resistance.However,TiO_(2)particles were hardly detected in the coating on TiFSP sample.
基金Funded by the National Natural Science Foundation of China(No.51201176)the Zhejiang Provincial Natural Science Foundation of China(No.Y2110401)the Natural Science Foundation of Shaanxi Province(No.2015JM5176)
文摘The combined microarc oxidation （MAO） and magnetron sputtering deposition process was used to deposit duplex a-C：H/MAO and Ti-a-C：H/MAO coatings on AM80 magnesium alloy. The microstructure, mechanical properties and tribological behavior of the two duplex coatings were investigated. The experimental results showed that the a-C：H and Ti-a-C：H top films on Si substrates were dense and had a low G peak position and ID/IG ratio, compared with the hydrogen-free amorphous carbon films. Numerous micropores were found on the duplex a-C：H/MAO and Ti-a-C：H/MAO coatings together with low values of hardness （H） and elastic modulus （E）, which also showed good binding strength with the Mg alloy substrates. Compared to MAO treated substrate used for the protection of the Mg alloy, the duplex a-C：H/MAO and Ti-a- C：H/MAO coatings still had stable and low value of friction coefficient, even though the surface of the duplex coatings was rough and porous. Furthermore, the mechanism of friction reduction of the two duplex coatings on the Mg alloy substrates was discussed.
基金supported by the National Natural Science Foundation of China(No.52001034)the China Postdoctoral Science Foundation(No.2023M731677)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX23_3032).
文摘Nano-zinc oxides(ZnO)demonstrate remarkable antibacterial properties.To further enhance the corrosion resistance and antibacterial efficiency of magnesium alloy micro-arc oxidation(MAO)coatings,this study investigates the preparation of ZnO-containing micro-arc oxidation coatings with dual functionality by incorporating nano-ZnO into MAO electrolyte.The influence of varying ZnO concentrations on the microstructure,corrosion resistance,and antibacterial properties of the coating was examined through microstructure analysis,immersion tests,electrochemical experiments,and antibacterial assays.The findings revealed that the addition of nano-ZnO significantly enhanced the corrosion resistance of the MAO-coated alloy.Specifically,when the ZnO concentration in the electrolyte was 5 g/L,the corrosion rate was more than ten times lower compared to the MAO coatings without ZnO.Moreover,the antibacterial efficacy of ZnO+MAO coating,prepared with a ZnO concentration of 5 g/L,surpassed 95%after 24 h of co-culturing with Staphylococcus aureus(S.aureus).The nano-ZnO+MAO-coated alloy exhibited exceptional degradation resistance,corrosion resistance,and antibacterial effectiveness.
基金supported by the National Key R&D Program of China(2021YFB3701100)the National Natural Science Foundation of China(52171101)the Fundamental Research Funds for the Central Universities(2024IAIS-QN009).
文摘Micro-arc oxidation(MAO)flm can only provide common mechanical protection for magnesium(Mg)–lithium(Li)alloys.These alloys are susceptible to severe localized corrosion,if the MAO flm is disrupted.This work reports the successful hydrothermal preparation of a MgLiAlCe-LDHs@GO flm on a MAO-coated Mg–Li alloy following Ce confnement.The graphene oxide(GO)sheet increased the difusion path of the corrosive media,and the addition of rare-earth cerium ions(Ce^(3+))endowed the flm with a certain self-healing ability,which signifcantly improved the corrosion resistance of the flm,and the corrosion current density(icorr)reached 3.27×10^(−8)A cm^(−2).The synergistic action of GO and Ce^(3+)can achieve long-term corrosion protection for the substrate.The corrosion resistance mechanism of MgLiAlCe-LDHs@GO flm was discussed by the scanning vibration electrode technique(SVET).
基金Project(11005151)supported by the Young Scientists Fund of the National Natural Science Foundation of ChinaProject(YETP1297)supported by the Beijing Higher Education Young Elite Teacher Project,ChinaProject(BEIJ2014110003)supported by the Undergraduate Research and Innovative Undertaking Program of Beijing,China
文摘The microarc oxidation（MAO） coatings produced at different current frequencies on AZ91 D magnesium alloys were studied systematically. The morphologies, thickness, corrosion performances, and tribological properties of the coatings were investigated by the scanning electron microscopy, the electrochemical measurement system, and MS-T3000 friction test rig, respectively. The results show that the structure of the coatings becomes denser, and thickness becomes thinner with the increase of the current frequency. It is also found that the corrosion resistance of the coatings produced at higher frequency is improved greatly and the difference of the corrosion current density becomes small with increasing current frequency, which is similar to that of the coating thickness. The tribological test shows that the friction coefficient decreases with increasing the current frequency and the wear resistance of the coatings is influenced by both the thickness and structures. All these results were explained by analyzing the growing process of the MAO coating.
基金Project (12504230006) supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions, China
文摘Microarc oxidation （MAO） process was conducted on AZ91D magnesium alloy in an electrolyte composed of NazSiO3, NaAlO2, NaEB4O7, NaOH, C3H803 and C6H5Na307 by AC pulse electrical source. The surface and cross-sectional morphologies, film thickness, chemical composition and structure of the coatings were characterized by scanning electron microscopy（SEM）, layer thickness metry, energy disperse spectroscopy（EDS） and X-ray diffraction（XRD）. The corrosiofi resistances of the coatings in a 3.5% NaC1 neutral solution were evaluated by electrochemical impedance spectroscopy （EIS） and potentiodynamic polarization test. The results showed that an optimized electrolyte with a composition of 15 g/L NazSiO3, 9 g/L NaA102, 2 g/L NazB407, 3 g/L NaOH, 5 mL/L C3H803 and 7 g/LC,HsNa307 was developed by means of orthogonal experiment. The coating obtained in the optimized electrolyte had a dense structure and revealed a lower current density, decreased by two orders of magnitude as compared with the magnesium substrate. Meanwhile, the corrosive potentials of the coated samples increased nearly by 73 inV. EIS result showed that the corrosion resistance of the coating was mainly determined by the inner dense layer. The coating primarily contained elements Mg, Al, O and Si and XRD analyses indicated that the coating was mainly composed of MgO, Mg2SiO4 and MgAl204.
文摘The effects of rare earths on the properties of the microarc oxidation（MAO） coating on a magnesium alloy were investigated by means of scanning electron microscopy（SEM）,energy dispersive X-ray spectroscopy（EDS）,and electrochemistry methods.The results show that a nice and compact MAO coating was successfully obtained when the magnesium alloy was treated in nitrate solutions as the pre-treatment of MAO.However,the MAO was not successfully completed for the silicate electrolytes with the addition of rare earths.After the magnesium alloy being treated by rare earth nitrate,the obtained MAO coating has advantages such as uniform distribution of thickness,improved corrosion resistance,and nice-uniform surface,as compared with the untreated magnesium alloy.In addition,the time of non-ESP,the voltage and current density of the MAO process obviously decrease.Cerium oxide doped on the surface of the magnesium alloy can significantly improve the corrosion resistance of the MAO coating and decrease the current density of the MAO process,as compared with lanthanum oxide,whereas the doped rare earths have no significant effect on the components of the MAO coating.
基金supported by the National Natural Science Foundation of China(No.51164023)Inner Mongolia Natural Science Foundation(No.2009BS0801)
文摘Zirconia coatings as hydrogen permeation barriers were formed on disktype ZrHj.s substrate speci mens in phosphate solution system by microarc oxidation technique. Influence of positive voltage on hydrogen per meation barriers on the surface of zirconium hydride was investigated as the main factor. The thickness of total oxide layer increased from 42.5 to 55.0 ~tm the increase of positive voltage increasing from 325 up to 425 V. The permeation reduction factor （PRF） was observed under different voltages, which increased with the increasing positive voltages. The phase structure of oxide layer was monoclinic Zr02 and tetragonal ZrO1.88. No reduction reaction occured in the process of hydrogen escaping, and it indicates that hydrogen permeation through oxide layer is restricted.
基金supported by the National Natural Science Foundation of China(No.51001036)the Fundamental Research Funds for the Central Universities(Nos. HEUCFR1021 and HEUCF201210001)
文摘Selective growth of oxidation coating was observed with Al18B4O33 crystal whisker as reinforced phase） on Mg matrix composite Al18B4O33w/AZ91 （a composite when this composite was treated by microarc oxidation （MAO） technique, and then the role of Al18B4O33 whisker in the process of MAO was analyzed. The protective properties of MAO coating also were investigated. Scanning electron microscopy （SEM） was used to characterize the existing state of Al18B4O33 whisker in MAO process and the microstructure of MAO coating. Corrosion resistance of the bare and coated composite was evaluated by immersion corrosion test and potentiodynamic polarizing test. Wear resistance of MAO coating was investigated by a ball-on-disc friction and wear tester. The results showed that sparking discharge did not occur on Al18B4O33 whisker and the whisker existed in the coating as a heterogeneous phase when MAO coating grew on the composite; then the whisker would be covered gradually with growing thick of the coating. Corrosion current density of the coated composite was decreased by 4 orders of magnitude compared with that of the uncoated composite; excellent corrosion resistance was closely related to the compact whisker-coating interface since Al18B4O33 whisker did not induce structural defects. The coating also exhibited high wear resistance and a slight adhesive wear tendency with bearing steel as its counterpart material.
文摘Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the surface ofpure titanium by alternating-current microarc discharge in aluminate solution were investigated byX-ray diffraction and scanning electron microscopy. The profiles of the hardness H and the elasticmodulus E in the coatings were determined using a nanoindentation method. The concentrationdistributions of Ti, Al, and O in the coating show that this coating over 30 mu m thick contains twolayers: an outer layer and an inner layer. The oxide coating is mainly composed of TiO_2 rutile andAl_2TiO_5 compounds. During oxidation, the temperature in the microarc discharge channel was veryhigh to make the local coating molten. From the surface to the interior of the coating, H and Eincrease gradually, and then reach maximum values of 9.78 GPa and 176 GPa respectively at a distanceof 7 mu m from the coating/titanium interface. They are also rather high near the interface.
基金financially supported by the International Technology Cooperation Plan in Guizhou Province (No.2012-7001)
文摘In this work, microarc oxidation(MAO) technology was used to form oxide ceramic coating on the surface of aluminum alloy. The combined additives nano-TiOand nano-ZnO were added into the silicate electrolyte, and the effect of the compound nano-additive on microstructure and properties of MAO coating was investigated. The results show that compared with those of the nano-additive-free coating formed on aluminum alloy, the thickness, hardness, abrasion resistance and corrosion resistance of the nano-additive-containing coating are obviously improved. The surface of coating with nanoadditive becomes smooth, dense, and there are less porosities and microcracks. Moreover, the content of crystal phase a-AlOand y-AlOincreases visibly on the nano-additive-containing MAO coatings, and new phases AlTi and ZnTiare detected in the coatings, which are mainly contributed to the excellent corrosion resistance and abrasion resistance of the film. When the contents of nano-TiOand nano-ZnO are, respectively, 4 and 2 g-L, the film has better comprehensive performance, the thickness and hardness of the film could reach 52 μm and HV 692,respectively.
基金supported by the National Natural Science Foundation of China(No.50171026)Harbin Special Creation Foundation of Science and Technology for Fellow of China(No.2006RFQXG032).
文摘Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation（MAO） in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings were studied by XRD and SEM,respectively.The growing mechanism of ceramic coatings was discussed in a preliminary manner.The results show that with an increase in MAO time,the compactness of the coating improved and the thickness increased.From the inner layer to the coating surface,the content of Zr increased,while the content of Al decreased.In addition,the coating was composed of m-ZrO2,t-ZrO2,and a little amount of γ-Al2O3.With an increase in reaction time,the relative content of t-ZrO2 within the coating sharply decreased while the relative content of m-ZrO2 sharply increased,and then both generally kept at a constant level after 60 min.
基金supports of the National Natural Science Foundation of China(No.51001036)the Fundamental Research Funds for the Central Universities(No.HEUCF20130910010)
文摘Selective growth of oxidation coating was observed on Mg alloy AZ91 D when this alloy was treated by microarc oxidation （MAO） technique, and then the role of intermetallic phase Mg17AI12 （β phase） during MAO was investigated. Corrosion resistance and anti-corrosion mechanism of the MAO coating were also studied. Optical microscopy and scanning electron microscopy （SEM） were used to characterize β phase and coating microstructure. Corrosion properties of the coated alloy were studied by potentiodynamic polarization test and electrochemical impedance spectroscopy （EIS） in 3.5% NaCI solution. Results showed that sparking discharge preferentially occurred on ^-Mg phase rather than on β phase at the early stage of MAO; however selective growth of the coating disappeared gradually with the increasing oxidation time and β phase would not further inhibit coating growth at the prolonged stage of MAO. MglTAI12 phase ultimately was unable to destroy the integrity and continuity of MAO coating. The MAO coating could restrain charge transfer process and then greatly enhance corrosion resistance of AZ91D alloy. Sealing treatment of MAO coating by stearic acid could further improve the corrosion resistance of AZ91 D alloy.
基金Project(51201176)supported by the National Natural Science Foundation of ChinaProject(2006BAE04B05-1)supported by the National Key Technologies of Research and Development Program of China
文摘The combined microarc oxidation (MAO) and inorganic sealing process was used to deposit a composite coating to improve the corrosion resistance of AZ31 magnesium alloy.The surface morphologies of the resulting duplex coatings were studied by SEM.Furthermore,the corrosion resistance of the coated Mg alloy substrates was investigated using electrochemical workstation and dropping corrosion test.The results show that the composite coating surface consists of Mg,Si,O and Na.It is difficult to deposit inorganic coating on a thick MAO coating surface.As the composite coating was solidified by CO2 under 175 °C,it exhibits a better corrosion resistance than the MAO monolayer,owing to the thick and compact inorganic coating.
基金This rescarch was sponsored by the National"863"High-tech Progran of China(No.715-011-020)the National Natural Science Foundation of China(No.59801003)Beijing New-Star Progratn for Science and Technology(No.9558102500).
文摘Dense ceramic oxide coatings of about 50 μm may be prepared on Ti-6AI-4V alloy surface by alternating-current microarc oxidation in aluminate and silicate solutions, respectively. Their phase constituent and microstructure were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the electrolytic ions have incorporated into the interior of the coatings. The coating formed in aluminate solution is composed of the rutile TiO2 and TiAl2O5 phases rather than the rutile, anatase and amorphous SiO2 phases for the coating formed in silicate solution. However, TiAl2O5 content in the outer layer of the two coatings is much higher than in the inner layer. It is suggested that all these oxides may result from a rapid solidification of the molten coating in the microarc discharge zone.
基金This work was supported by Special Fund for Local Science and Technology Development from the Ministry of Science and Technology of China(2020ZYD053)Science and Technology Planning Project of Zigong(2019YYJC22)Opening Project of Key Laboratories of Fine Chemicals and Surfactants in Sichuan Provincial Universities(2020JXY05).
文摘A reliable,high-performance coating procedure was developed using PDMS to modify a duplex MAO/DLC coating on an AZ31B Mg alloy.First,the duplex MAO/DLC coating was fabricated via a combined MAO and unbalanced magnetron sputter process.Subsequently,a PDMS solution was used to modify the MAO/DLC coating via a conventional dip-coating method.The surface characteristics,bond strength,hardness,tribological behaviour,and corrosion resistance of the coated samples were evaluated via SEM,CA,Raman spectroscopy,friction and wear behaviour,polarisation curve,and NSS tests.The PDMS modification reduced the HIT of MAO/DLC coating from 15.96 to 8.34GPa;this is ascribed to the penetration of PDMS,which has good rheological properties to form a viscoelastic Si-based organic polymer layer on the MAO/DLC coating.However,the PDMS-modified MAO/DLC coating was denser,hydrophobic,and had higher bond strength compared with MAO-and MAO/DLC-coated samples.Moreover,the PDMS modification reduced the COF and wear rate of the duplex MAO/DLC coating.This indicates that the PDMS improved the tribological behaviour owing to the transferred Si oxide that originated from the Si-O network of the PDMS,as well as the low graphitisation of the DLC layer during sliding.Furthermore,the corrosion current density of the MAO/DLC-coated sample modified by PDMS for 10min decreased by two order of magnitude compared with that of the MAO/DLC-coated sample but by five orders of magnitude compared with that of the bare substrate.The NSS tests proved that the PDMS layer slowed the corrosion of the Mg alloy under long-term service,enhancing the corrosion protection efficiency.The results are attributed to the high bond strength and lubricant MAO/DLC layer,and the dual role of sealing and hydrophobicity of PDMS.Therefore,PDMS modification is promising for the fabrication of protective materials for Mg alloys that require corrosion and wear resistance.
基金financially supported by China Postdoctoral Science Foundation (No.2021M700569)Chongqing Postdoctoral Science Foundation (No.cstc2021jcyj-bsh0133)
文摘Microarc oxidation(MAO)is an effective surface treatment method for Ti alloys to allow their application in extreme environments.Here,binary electrolytes consisting of different amounts of sodium phosphate and sodium silicate were designed for MAO.The surface morphology,composition,and properties of MAO coatings on Ti-6Al-4V alloy treated in 0.10 mol/L electrolyte were investigated to reveal the effect of PO_(4)^(3-)and SiO_(3)^(2-)ray diffraction,and potentiodynamic polarization.The results showed that PO_(4)^(3-)is beneficial for generating microarcs and forming pores within the coating,resulting in a thick but porous coating.SiO_(3)^(2-)eration of microarcs,resulting in a thin dense coating.The thickness,density,phases content,and polarization resistance of the MAO coatings are primarily affected by the intensity of microarcs for low SiO_(3)^(2-)ciently high.The thickness of MAO coatings obtained in P/Si electrolytes shows a piecewise linear increase with increasing process time during the three stages of microarc discharge.SiO_(3)^(2-)discharge,but slows down the growth of the coating formed in the next stage.
基金the Department of Metallurgical and Materials Engineering,National Institute of Technology,Tiruchirapalli for providing the funds and facilities to conduct this research work
文摘In this work, the morphology, phase composition, and corrosion properties of microarc oxidized (MAO) gas tungsten arc (GTA) weldments of AZ31 alloy were investigated. Autogenous gas tungsten arc welds were made as full penetration bead-on-plate welding under the alternating-current mode. A uniform oxide layer was developed on the surface of the specimens with MAO treatment in silicate-based alkaline electrolytes for different oxidation times. The corrosion behavior of the samples was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy. The oxide film improved the corrosion resistance substantially compared to the uncoated specimens. The sample coated for 10 min exhibited better corrosion properties. The corrosion resistance of the coatings was concluded to strongly depend on the morphology, whereas the phase composition and thickness were concluded to only slightly affect the corrosion resistance.
