The role of cold nitrogen gas and oil mist on tool wear and surface roughness is investigated in turning the K424 nickel-base super alloy with Sialon and SiC whisker-reinforced alumina ceramic tools. A new cooling sys...The role of cold nitrogen gas and oil mist on tool wear and surface roughness is investigated in turning the K424 nickel-base super alloy with Sialon and SiC whisker-reinforced alumina ceramic tools. A new cooling system is developed and used to lower the temperature of the compressed nitrogen gas. Experiments are performed in three different cooling/lubrication modes, i.e. the dry cutting, the cold nitrogen gas （CNG）, and the cold nitrogen gas and oil mist （CNGOM）. Experimental results show that the depth-of-cut notching severely limits the tool life in all the cooling/lubrication modes. Compared with the dry cutting, the use of CNG and CNGOMcan yield higher wear rate of depth-of-cut notching and worse surface finish.展开更多
A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC mac...A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.展开更多
Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro...Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro-structure has been applied on the micro-grinding tool.A morphology modeling has been established in this study to characterize the surface of microstructured micro-grinding tool,and the grinding performance of micro-structured micro-grinding tool has been analyzed through undeformed chip thickness,abrasive edge width,and effective distance between abrasives.Then deviation analysis,path optimization and parameter optimization of microchannel array precision grinding have been finished to improve processing quality and efficiency,and the deflection angle has the most obvious effects on the rectangular slot depth,micro-structured micro-grinding tool could reduce 10%surface roughness and 20%grinding force compared to original micro-grinding tool.Finally,the microchannel array has been machined with a size deviation of 2μm and surface roughness of 0.2μm.展开更多
Cardiovascular disease is the leading cause of human mortality,and calcified tissue blocking blood vessels is the main cause of major adverse cardiovascular events(MACE).Rotational Atherectomy(RA)is a minimally invasi...Cardiovascular disease is the leading cause of human mortality,and calcified tissue blocking blood vessels is the main cause of major adverse cardiovascular events(MACE).Rotational Atherectomy(RA)is a minimally invasive catheterbased treatment method that involves high-speed cutting of calcified tissue using miniature tools for removal.However,the cutting forces,heat,and debris can induce tissue damage and give rise to serious surgical complications.To enhance the effectiveness and efficiency of RA,a novel eccentric rotational cutting tool,with one side comprising axial and circumferential staggered micro-blades,was designed and fabricated in this study.In addition,a series of experiments were conducted to analyze their performance across five dimensions:tool kinematics,force,temperature,debris,and surface morphology of the specimens.Experimental results show that the force,temperature and debris size of the novel tool were well inhibited at the highest rotational speed.For the tool of standard clinical size(diameter 1.25 mm),the maximum force is 0.75 N,with a maximum temperature rise in the operation area of 1.09℃.Debris distribution followed a normal distribution pattern,with 90%of debris measuring smaller than 9.12μm.All tool metrics met clinical safety requirements,indicating its superior performance.This study provides a new idea for the design of calcified tissue removal tools,and contributes positively to the advancement of RA.展开更多
Smart machining has tremendous potential and is becoming one of new generation high value precision manufacturing technologies in line with the advance of Industry 4.0 concepts. This paper presents some innovative des...Smart machining has tremendous potential and is becoming one of new generation high value precision manufacturing technologies in line with the advance of Industry 4.0 concepts. This paper presents some innovative design concepts and, in particular, the development of four types of smart cutting tools, including a force-based smart cutting tool, a temperature-based internally-cooled cutting tool, a fast tool servo （FTS） and smart collets for ultra- precision and micro manufacturing purposes. Implemen- tation and application perspectives of these smart cutting tools are explored and discussed particularly for smart machining against a number of industrial application requirements. They are contamination-free machining, machining of tool-wear-prone Si-based infra-red devices and medical applications, high speed micro milling and micro drilling, etc. Furthermore, implementation tech- niques are presented focusing on： （a） plug-and-produce design principle and the associated smart control algo- rithms, （b） piezoelectric film and surface acoustic wave transducers to measure cutting forces in process, （c） critical cutting temperature control in real-time machining, （d） in- process calibration through machining trials, （e） FE-based design and analysis of smart cutting tools, and （f） applica- tion exemplars on adaptive smart machining.展开更多
Vibration cutting has emerged as a promising method for creating surface functional microstructures.However,achieving precise tool setting is a time-consuming process that significantly impacts process efficiency.This...Vibration cutting has emerged as a promising method for creating surface functional microstructures.However,achieving precise tool setting is a time-consuming process that significantly impacts process efficiency.This study proposes an intelligent approach for tool setting in vibration cutting using machine vision and hearing,divided into two steps.In the first step,machine vision is employed to achieve rough precision in tool setting within tens of micrometers.Subsequently,in the second step,machine hearing utilizes sound pickup to capture vibration audio signals,enabling fine tool adjustment within 1μm precision.The relationship between the spectral intensity of vibration audio and cutting depth is analyzed to establish criteria for tool–workpiece contact.Finally,the efficacy of this approach is validated on an ultra-precision platform,demonstrating that the automated tool-setting process takes no more than 74 s.The total cost of the vision and hearing sensors is less than$1500.展开更多
Recent advancements in drilling technology have driven substantial progress in cuttings removal tool development,particularly for addressing borehole cleaning challenges in highly deviated directional critical factors...Recent advancements in drilling technology have driven substantial progress in cuttings removal tool development,particularly for addressing borehole cleaning challenges in highly deviated directional critical factors in operational safety and efficiency improvement.Despite these innovations,two fundamental challenges persist:an incomplete understanding of mechanistic cuttings removal processes and an insufficient methodological framework for optimal tool installation.Studying the installation positions and assessing the effects of two cuttings removal are essential steps to advance the application of such tools.This investigation was initiated with a comprehensive analysis of particle settling dynamics and migration behaviors in annular wellbore spaces.Building upon Moore's terminal settling velocity equation,a modified model was developed to characterize the transport patterns of cuttings.Through model integration,the precise positioning of the efficient Vortex Cuttings Removal Tool(VCRT)was determined at 188 m from the bit.Subsequently,Computational Fluid Dynamics(CFD)numerical simulation was employed to reveal distinct annular flow field characteristics between VCRT and conventional drilling tools.Field validation in Well Z401X demonstrated a strong correlation between empirical measurements and simulated predictions,with pressure drop deviations of 6.25%and rotational speed variances limited to 7.50%.Analytical results confirmed VCRT's superior performance,exhibited 36.43%reductions in cuttings accumulation at the wellbore's lower quadrant compared to conventional drilling tools.The application of VCRT accelerated cuttings migration velocity in the annular space,significantly increasing the volume of returned onsite cuttings.Friction resistance decreased by approximately 35.90%,indicating higher cuttings removal efficiency than conventional drilling tools.展开更多
The research of rare earth elements (RE), added into cemented carbide tools, is one of the recent developments of new types of tool materials in China. Systematic experiments about RE carbides YG8R. (K30), YT14R (P20)...The research of rare earth elements (RE), added into cemented carbide tools, is one of the recent developments of new types of tool materials in China. Systematic experiments about RE carbides YG8R. (K30), YT14R (P20) and, YW1R (M10) were made to study on the cutting performance in comparison with non-RE carbides YG8, YT14 and YW1. The cutting experiments were as follows: tool life, cutting force, tool-chip friction coefficient and interrupted machining. The action of RE on the carbide materials and the cutting mechanism of the RE carbide tools in the cutting process were verified with the aid of SEM and energy spectrum analysis. Experimental results show that the RE carbide tools have a good overall performance.展开更多
As one of the most important terminals in machining, cutting tools have been widely used for components manufacturing in aerospace and other industries. The quality of these components and processing efficiency are cl...As one of the most important terminals in machining, cutting tools have been widely used for components manufacturing in aerospace and other industries. The quality of these components and processing efficiency are closely linked to the performance of cutting tools. Therefore, it is essential and critical to inspect the cutting tools and monitor the condition during the stage of manufacturing and machining. This review aims to discuss and summarize the key problems, methods,and techniques from the perspective of the tool geometric and the physical quantities measurement,including machine vision, physical sensors and data processing. It is worth mentioning that we focus on the topic of precision measurement methods and discuss universal solutions by identifying the common characteristics of the measured quantities. Eventually, the challenges and future trends for the development of in-depth research and practical applications are concluded. The research and application of precise measurement techniques for geometric and physical quantities will better promote the development of intelligent manufacturing.展开更多
Diamond tools play a critical role in ultra-precision machining due to their excellent physical and mechanical material properties,such as that cutting edge can be sharpened to nanoscale accuracy.However,abrasive chem...Diamond tools play a critical role in ultra-precision machining due to their excellent physical and mechanical material properties,such as that cutting edge can be sharpened to nanoscale accuracy.However,abrasive chemical reactions between diamond and non-diamond-machinable metal elements,including Fe,Cr,Ti,Ni,etc,can cause excessive tool wear in diamond cutting of such metals and most of their alloys.This paper reviews the latest achievements in the chemical wear and wear suppression methods for diamond tools in cutting of ferrous metals.The focus will be on the wear mechanism of diamond tools,and the typical wear reduction methods for diamond cutting of ferrous metals,including ultrasonic vibration cutting,cryogenic cutting,surface nitridation and plasma assisted cutting,etc.Relevant commercially available devices are introduced as well.Furthermore,future research trends in diamond tool wear suppression are discussed and examined.展开更多
C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short too...C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short tool life and low productivity. In this paper, a newly developed Ti（C7N3）-based cermet insert manufactured by a hot-pressing method is used to machine the C-276 nickel-based alloy, and its cutting performances are studied. Based on orthogonal experiment method, the influence of cutting parameters on tool life, material removal rates and surface roughness are investigated. Experimental research results indicate that the optimal cutting condition is a cutting speed of 50 m/min, depth of cut of 0.4 mm and feed rate of 0.15 mm/r if the tool life and material removal rates are considered comprehensively. In this case, the tool life is 32 min and material removal rates are 3000 mm^3/min, which is appropriate to the rough machining. If the tool life and surface roughness are considered, the better cutting condition is a cutting speed of 75 m/min, depth of cut of 0.6 mm and feed rate of 0.1 mm/r. In this case, the surface roughness is 0.59μm. Notch wear, flank wear, chipping at the tool nose, built-up edge（BUE） and micro-cracks are found when Ti（C7N3）-based cermet insert turned Hastelloy C-276. Oxidation, adhesive, abrasive and diffusion are the wear mechanisms, which can be investigated by the observations of scanning electron microscope and energy-dispersive spectroscopy. This research will help to guide studies on the evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy C-276 machining.展开更多
An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and f...An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.展开更多
Cutting tools are known as the“productivity”of the manufacturing industry,which affects the production efficiency and quality of the workpiece,and has become the focus of research and attention in academia and indus...Cutting tools are known as the“productivity”of the manufacturing industry,which affects the production efficiency and quality of the workpiece,and has become the focus of research and attention in academia and industry.However,traditional cutting tools often suffer from adhesion or wear during the cutting process,which considerably reduces the cutting efficiency and service life of the tools,and makes it difficult to meet current production requirements.To solve the above problems,scholars have introduced bionics into the tool’s design,applying the microscopic structure of the biological surface to the tool surface to alleviate the tool’s failure.This paper mainly summarizes the research progress of bionic textured cutting tools.Firstly,categorize whether the bionic texture design is inspired by a single organism or multiple organisms.Secondly,it is discussed that the non-smooth surface of the biological surface has five characteristics:hydrophilic lubricity,wear resistance,drag reduction and hydrophobicity,anti-adhesion,and arrangement,and the non-smooth structure of these different characteristics are applied to the surface of the tool is designed with bionic texture.Furtherly,the cutting performance of bionic textured cutting tools is discussed.The anti-friction and wear-resisting mechanism of bionic textured cutting tools is analyzed.Finally,some pending problems and perspectives have been proposed to provide new inspirations for the design of bionic textured cutting tools.展开更多
The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the ...The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the workpiece critical hardness is proved. The life equationat two kinds of workpiece hardness demonstrates that the effect of the cutting speed on the PCBNtool life is less than that of carbide tools and ceramic tools.展开更多
There were only two kinds of superhard tool material at the past, i.e. diamond and cubic boron nitride (CBN). Manmade diamond and CBN are manufactured by the middle of 20th century. Various manufacturing methods and m...There were only two kinds of superhard tool material at the past, i.e. diamond and cubic boron nitride (CBN). Manmade diamond and CBN are manufactured by the middle of 20th century. Various manufacturing methods and manmade superhard materials were developed later. They were widely used in different industry and science areas. Recently, a new kind of superhard tool material, C 3N 4 coating film, had been developed. American physical scientists, A. M. Liu and M. L. Cohen, designed a new kind of inorganic compound C 3N 4 with the theory of molecule engineering. According to calculation, it can reach or even exceed the hardness of diamond, so material scientists and technique circles draw their attention to it. A high speed steel twist drill coated with C 3N 4 film is applied to the drilling hole process on steel workpiece in cutting tests, the tool life is increased greatly. When the C 3N 4 film is coated on the cemented carbide inserts, the cutting performance is improved, but is not good enough. The data of mechanical performance and cutting tests about this kind of new tool material is given in this paper, it shows that C 3N 4 has a promising future. The anti-wear ability of cutting tool increases sharply after C 3N 4 being coated on HSS tool. Coated HSS drill also has some benefit after being reground. The tool life prolongs after C 3N 4 being coated on cemented carbide inserts, but is not so long as that of C 3N 4 coated HSS tool. When machining PRCM with C 3N 4 thin-film coated cemented carbide tool, the cutting performance is poor and it is much better when machining PRCM with PCBN, PCD compound plates and CVD thick-film coated cutting tool. Some relative aspects need to be deeply discussed and researched, e.g. the existing coating techniques is not good enough and should be improved in the future, the film thickness should be optimized and try to find out the most effective value, the binding force and mutual effect between coated film and substrate need to be studied furtherly, etc.展开更多
High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due...High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.展开更多
This work was carried out with the aim of using alloying and ageing processes to develop new alloys from grey cast iron that will have optimum properties suitable for the manufacturing of machine cutting tools. Four d...This work was carried out with the aim of using alloying and ageing processes to develop new alloys from grey cast iron that will have optimum properties suitable for the manufacturing of machine cutting tools. Four different alloys of grey cast iron with alloying composition of Fe-3% Al-2.5% Cr-2% Mo;Fe-3% Al-2% Cr-2% Mo;Fe-3% Al-2.5% Cr-1.5% Mo and Fe-3% Al-1.5% Cr-2% Mo were produced. The chemical analysis of both as-received base metal and produced alloys was determined using Spetro-CJRO Arc-Spectrometer. The microstructural properties and mechanical properties (hardness, impact toughness and ultimate tensile strength) of the produced alloys were determined for both as-cast samples and aged samples. The results showed that the addition of these alloying elements slightly decreased carbon, silicon and phosphorus content and thereby changed the hypereutectic cast iron to hypoeutectic by reducing the carbon equivalent. Also the morphology of graphite flake was changed as a result of the formation of nitrides and carbides of different phases. The results of the mechanical properties showed that the maximum hardness values obtained for each of the four alloys produced and aged at 300?C are 71.5 HRc, 69 HRc, 66.5 HRc and 65.4 HRc respectively. The maximum values for impact toughness obtained for each of the same produced alloys are 66 J, 63.6 J, 62 J and 60.3 J respectively. Also the maximum ultimate tensile strength values obtained for each of the alloys are 1380 N·mm-2, 1311 N·mm-2, 1260 N·mm-2 and 1190 N·mm-2. Comparing the properties obtained from the produced alloys with those of the commercial cutting tools, it was found that cutting tools manufactured from these produced alloys can compete favourably with cast cobalt tool, high speed steel (HSS) and tool steel.展开更多
Wear of cutting tools is a big concern for industrial manufacturers, because of their acquisition cost as well as the impact on the production lines when they are unavailable. Law of wear is very important in determin...Wear of cutting tools is a big concern for industrial manufacturers, because of their acquisition cost as well as the impact on the production lines when they are unavailable. Law of wear is very important in determining cutting tools lifespan, but most of the existing models don’t take into account the cutting temperature. In this work, the theoretical and experimental results of a dynamic study of metal machining against cutting temperature of a treated steel of grade S235JR with a high-speed steel tool are provided. This study is based on the analysis of two complementary approaches, an experimental approach with the measurement of the temperature and on the other hand, an approach using modeling. Based on unifactorial and multifactorial tests (speed of cut, feed, and depth of cut), this study allowed the highlighting of the influence of the cutting temperature on the machining time. To achieve this objective, two specific approaches have been selected. The first was to measure the temperature of the cutting tool and the second was to determine the wear law using Rayleigh-Ham dimensional analysis method. This study permitted the determination of a law that integrates the cutting temperature in the calculations of the lifespan of the tools during machining.展开更多
Micro diamond tools are indispensable for the efficient machining of microstructured surfaces.The precision in tool manufacturing and cutting performance directly determines the processing quality of components.The ma...Micro diamond tools are indispensable for the efficient machining of microstructured surfaces.The precision in tool manufacturing and cutting performance directly determines the processing quality of components.The manufacturing of high-quality micro diamond tools relies on scientific design methods and appropriate processing techniques.However,there is currently a lack of systematic review on the design and manufacturing methods of micro diamond tools in academia.This study systematically summarizes and analyzes modern manufacturing methods for micro diamond tools,as well as the impact of tool waviness,sharpness,and durability on machining quality.Subsequently,a design method is proposed based on the theory of cutting edge strength distribution to enhance tool waviness,sharpness,and durability.Finally,this paper presents current technical challenges faced by micro diamond tools along with potential future solutions to guide scientists in this field.The aim of this review is to contribute to the further development of the current design and manufacturing processes for micro diamond cutting tools.展开更多
In spite of the considerable progress made in the domain of the sciences of materials, cutting tools subjected to an intense abrasive wear and a very high temperature of edge. They record during their use an reduced w...In spite of the considerable progress made in the domain of the sciences of materials, cutting tools subjected to an intense abrasive wear and a very high temperature of edge. They record during their use an reduced working life. The operations of machining on lathe are regularly stopped for replacing these tools, which influences enormously the production process. Indeed, the search the new materials of substitution, remain a domain very coveted, owing to the fact, it belongs to one stake very significant industrial, in particular, in the mechanical domain and its varied sectors. The recourse to the thermal treatments traditional, limiting in an interval, reduces the wear and the excessive consumption of these cutting tools, but the principal concern of the experts and researchers, in the domain of the mechanical engineering, remain posed. The goal of this study is the introduction of the technique of plasmas, as physical phenomenon, for making material of coating at base of titanium nitrides doped at iron, at the different concentrations. To this objective, one magnetron sputtering with plasma was used for the realization of the coatings deposed on the active parts of the cutting tools. During the experimentation, it was noted that the cutting tools which are treated by plasma, subjected to the machining operations on lathe and the hardness tests, presents one improvement of their hardness and a remarkable increase in their lifespan.展开更多
文摘The role of cold nitrogen gas and oil mist on tool wear and surface roughness is investigated in turning the K424 nickel-base super alloy with Sialon and SiC whisker-reinforced alumina ceramic tools. A new cooling system is developed and used to lower the temperature of the compressed nitrogen gas. Experiments are performed in three different cooling/lubrication modes, i.e. the dry cutting, the cold nitrogen gas （CNG）, and the cold nitrogen gas and oil mist （CNGOM）. Experimental results show that the depth-of-cut notching severely limits the tool life in all the cooling/lubrication modes. Compared with the dry cutting, the use of CNG and CNGOMcan yield higher wear rate of depth-of-cut notching and worse surface finish.
文摘A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.
基金co-supported by the Enterprise Innovation and Development Joint Program of the National Natural Science Foundation of China(No.U20B2032)Open Project Funding of State Key Laboratory for High Performance Tools(GXNGJSKL-2024-08)+1 种基金Open Foundation of the State Key Laboratory of Intelligent Manufacturing Equipment and Technology(IMETKF2023005)Introduced Innovative Scientific Research Team Project of Zhongshan(the tenth batch)(CXTD2023008)。
文摘Micro-grinding has been widely used in aerospace and other industry.However,the small diameter of the micro-grinding tool has limited its machining performance and efficiency.In order to solve the above problems,micro-structure has been applied on the micro-grinding tool.A morphology modeling has been established in this study to characterize the surface of microstructured micro-grinding tool,and the grinding performance of micro-structured micro-grinding tool has been analyzed through undeformed chip thickness,abrasive edge width,and effective distance between abrasives.Then deviation analysis,path optimization and parameter optimization of microchannel array precision grinding have been finished to improve processing quality and efficiency,and the deflection angle has the most obvious effects on the rectangular slot depth,micro-structured micro-grinding tool could reduce 10%surface roughness and 20%grinding force compared to original micro-grinding tool.Finally,the microchannel array has been machined with a size deviation of 2μm and surface roughness of 0.2μm.
基金Supported by National Natural Science Foundation of China(Grant No.52205455)Fujian Provincial Health Technology Project(Grant Nos.2022CXA005,2022CXA015)。
文摘Cardiovascular disease is the leading cause of human mortality,and calcified tissue blocking blood vessels is the main cause of major adverse cardiovascular events(MACE).Rotational Atherectomy(RA)is a minimally invasive catheterbased treatment method that involves high-speed cutting of calcified tissue using miniature tools for removal.However,the cutting forces,heat,and debris can induce tissue damage and give rise to serious surgical complications.To enhance the effectiveness and efficiency of RA,a novel eccentric rotational cutting tool,with one side comprising axial and circumferential staggered micro-blades,was designed and fabricated in this study.In addition,a series of experiments were conducted to analyze their performance across five dimensions:tool kinematics,force,temperature,debris,and surface morphology of the specimens.Experimental results show that the force,temperature and debris size of the novel tool were well inhibited at the highest rotational speed.For the tool of standard clinical size(diameter 1.25 mm),the maximum force is 0.75 N,with a maximum temperature rise in the operation area of 1.09℃.Debris distribution followed a normal distribution pattern,with 90%of debris measuring smaller than 9.12μm.All tool metrics met clinical safety requirements,indicating its superior performance.This study provides a new idea for the design of calcified tissue removal tools,and contributes positively to the advancement of RA.
基金Supported by the UK Technology Strategy Board(TSB)(SEEM Project,Contract No.:BD266E)Innovate UK(KTP Project,Contract No.:9277)
文摘Smart machining has tremendous potential and is becoming one of new generation high value precision manufacturing technologies in line with the advance of Industry 4.0 concepts. This paper presents some innovative design concepts and, in particular, the development of four types of smart cutting tools, including a force-based smart cutting tool, a temperature-based internally-cooled cutting tool, a fast tool servo （FTS） and smart collets for ultra- precision and micro manufacturing purposes. Implemen- tation and application perspectives of these smart cutting tools are explored and discussed particularly for smart machining against a number of industrial application requirements. They are contamination-free machining, machining of tool-wear-prone Si-based infra-red devices and medical applications, high speed micro milling and micro drilling, etc. Furthermore, implementation tech- niques are presented focusing on： （a） plug-and-produce design principle and the associated smart control algo- rithms, （b） piezoelectric film and surface acoustic wave transducers to measure cutting forces in process, （c） critical cutting temperature control in real-time machining, （d） in- process calibration through machining trials, （e） FE-based design and analysis of smart cutting tools, and （f） applica- tion exemplars on adaptive smart machining.
基金the financial support for this research provided by the National Natural Science Foundation of China(Grant Nos.52275470,124115301,and 52105458)the Natural Science Foundation of Beijing(Grant No.3222009).
文摘Vibration cutting has emerged as a promising method for creating surface functional microstructures.However,achieving precise tool setting is a time-consuming process that significantly impacts process efficiency.This study proposes an intelligent approach for tool setting in vibration cutting using machine vision and hearing,divided into two steps.In the first step,machine vision is employed to achieve rough precision in tool setting within tens of micrometers.Subsequently,in the second step,machine hearing utilizes sound pickup to capture vibration audio signals,enabling fine tool adjustment within 1μm precision.The relationship between the spectral intensity of vibration audio and cutting depth is analyzed to establish criteria for tool–workpiece contact.Finally,the efficacy of this approach is validated on an ultra-precision platform,demonstrating that the automated tool-setting process takes no more than 74 s.The total cost of the vision and hearing sensors is less than$1500.
基金supported by the National Natural Science Foundation of China(No.52374008,No.52174003)Shanghai Leading Academic Discipline Project(No,S30106).
文摘Recent advancements in drilling technology have driven substantial progress in cuttings removal tool development,particularly for addressing borehole cleaning challenges in highly deviated directional critical factors in operational safety and efficiency improvement.Despite these innovations,two fundamental challenges persist:an incomplete understanding of mechanistic cuttings removal processes and an insufficient methodological framework for optimal tool installation.Studying the installation positions and assessing the effects of two cuttings removal are essential steps to advance the application of such tools.This investigation was initiated with a comprehensive analysis of particle settling dynamics and migration behaviors in annular wellbore spaces.Building upon Moore's terminal settling velocity equation,a modified model was developed to characterize the transport patterns of cuttings.Through model integration,the precise positioning of the efficient Vortex Cuttings Removal Tool(VCRT)was determined at 188 m from the bit.Subsequently,Computational Fluid Dynamics(CFD)numerical simulation was employed to reveal distinct annular flow field characteristics between VCRT and conventional drilling tools.Field validation in Well Z401X demonstrated a strong correlation between empirical measurements and simulated predictions,with pressure drop deviations of 6.25%and rotational speed variances limited to 7.50%.Analytical results confirmed VCRT's superior performance,exhibited 36.43%reductions in cuttings accumulation at the wellbore's lower quadrant compared to conventional drilling tools.The application of VCRT accelerated cuttings migration velocity in the annular space,significantly increasing the volume of returned onsite cuttings.Friction resistance decreased by approximately 35.90%,indicating higher cuttings removal efficiency than conventional drilling tools.
文摘The research of rare earth elements (RE), added into cemented carbide tools, is one of the recent developments of new types of tool materials in China. Systematic experiments about RE carbides YG8R. (K30), YT14R (P20) and, YW1R (M10) were made to study on the cutting performance in comparison with non-RE carbides YG8, YT14 and YW1. The cutting experiments were as follows: tool life, cutting force, tool-chip friction coefficient and interrupted machining. The action of RE on the carbide materials and the cutting mechanism of the RE carbide tools in the cutting process were verified with the aid of SEM and energy spectrum analysis. Experimental results show that the RE carbide tools have a good overall performance.
基金co-supported by the National Key Research and Development Project of China (No. 2018YFA0703304)the National Natural Science Foundation of China (Nos. 52125504, 92148301, 52090053)。
文摘As one of the most important terminals in machining, cutting tools have been widely used for components manufacturing in aerospace and other industries. The quality of these components and processing efficiency are closely linked to the performance of cutting tools. Therefore, it is essential and critical to inspect the cutting tools and monitor the condition during the stage of manufacturing and machining. This review aims to discuss and summarize the key problems, methods,and techniques from the perspective of the tool geometric and the physical quantities measurement,including machine vision, physical sensors and data processing. It is worth mentioning that we focus on the topic of precision measurement methods and discuss universal solutions by identifying the common characteristics of the measured quantities. Eventually, the challenges and future trends for the development of in-depth research and practical applications are concluded. The research and application of precise measurement techniques for geometric and physical quantities will better promote the development of intelligent manufacturing.
基金This work was supported by Science Challenge Project(Nos.TZ2016006-0103 and TZ2016006-0107-02)National Natural Science Foundation of China(Nos.90923025 and 51905194)Science Fund for Creative Research Groups of NSFC(No.51621064).The sincere thanks are given to Professor Zhang Xinquan(Shanghai Jiao Tong University)for his comments,and Mr Xu Yongbo for his kind assistance.
文摘Diamond tools play a critical role in ultra-precision machining due to their excellent physical and mechanical material properties,such as that cutting edge can be sharpened to nanoscale accuracy.However,abrasive chemical reactions between diamond and non-diamond-machinable metal elements,including Fe,Cr,Ti,Ni,etc,can cause excessive tool wear in diamond cutting of such metals and most of their alloys.This paper reviews the latest achievements in the chemical wear and wear suppression methods for diamond tools in cutting of ferrous metals.The focus will be on the wear mechanism of diamond tools,and the typical wear reduction methods for diamond cutting of ferrous metals,including ultrasonic vibration cutting,cryogenic cutting,surface nitridation and plasma assisted cutting,etc.Relevant commercially available devices are introduced as well.Furthermore,future research trends in diamond tool wear suppression are discussed and examined.
基金Supported by Program for New Century Excellent Talents in University of China(Grant No.NCET-13-0357)Shandong Provincial Natural Science Foundation of China(Grant No.ZR2014EEM026)Tai Shan Scholar Foundation of China
文摘C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short tool life and low productivity. In this paper, a newly developed Ti（C7N3）-based cermet insert manufactured by a hot-pressing method is used to machine the C-276 nickel-based alloy, and its cutting performances are studied. Based on orthogonal experiment method, the influence of cutting parameters on tool life, material removal rates and surface roughness are investigated. Experimental research results indicate that the optimal cutting condition is a cutting speed of 50 m/min, depth of cut of 0.4 mm and feed rate of 0.15 mm/r if the tool life and material removal rates are considered comprehensively. In this case, the tool life is 32 min and material removal rates are 3000 mm^3/min, which is appropriate to the rough machining. If the tool life and surface roughness are considered, the better cutting condition is a cutting speed of 75 m/min, depth of cut of 0.6 mm and feed rate of 0.1 mm/r. In this case, the surface roughness is 0.59μm. Notch wear, flank wear, chipping at the tool nose, built-up edge（BUE） and micro-cracks are found when Ti（C7N3）-based cermet insert turned Hastelloy C-276. Oxidation, adhesive, abrasive and diffusion are the wear mechanisms, which can be investigated by the observations of scanning electron microscope and energy-dispersive spectroscopy. This research will help to guide studies on the evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy C-276 machining.
基金Selected from Proceedings of the 7th International Conference on Frontiers of DesignManufacturing(ICFDM'2006)This project is supported by National Natural Science Foundation of China(No.50275086)the University of New South Wales Visiting Professorship Scheme,Australia.
文摘An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.
基金supported by National Natural Science Foundation of China(52175431)Natural Science Foundation of Tianjin of China(22JCZDJC00730).
文摘Cutting tools are known as the“productivity”of the manufacturing industry,which affects the production efficiency and quality of the workpiece,and has become the focus of research and attention in academia and industry.However,traditional cutting tools often suffer from adhesion or wear during the cutting process,which considerably reduces the cutting efficiency and service life of the tools,and makes it difficult to meet current production requirements.To solve the above problems,scholars have introduced bionics into the tool’s design,applying the microscopic structure of the biological surface to the tool surface to alleviate the tool’s failure.This paper mainly summarizes the research progress of bionic textured cutting tools.Firstly,categorize whether the bionic texture design is inspired by a single organism or multiple organisms.Secondly,it is discussed that the non-smooth surface of the biological surface has five characteristics:hydrophilic lubricity,wear resistance,drag reduction and hydrophobicity,anti-adhesion,and arrangement,and the non-smooth structure of these different characteristics are applied to the surface of the tool is designed with bionic texture.Furtherly,the cutting performance of bionic textured cutting tools is discussed.The anti-friction and wear-resisting mechanism of bionic textured cutting tools is analyzed.Finally,some pending problems and perspectives have been proposed to provide new inspirations for the design of bionic textured cutting tools.
基金This project is supported by Provincial Natural Science Foundation of China(No.59975026).
文摘The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the workpiece critical hardness is proved. The life equationat two kinds of workpiece hardness demonstrates that the effect of the cutting speed on the PCBNtool life is less than that of carbide tools and ceramic tools.
文摘There were only two kinds of superhard tool material at the past, i.e. diamond and cubic boron nitride (CBN). Manmade diamond and CBN are manufactured by the middle of 20th century. Various manufacturing methods and manmade superhard materials were developed later. They were widely used in different industry and science areas. Recently, a new kind of superhard tool material, C 3N 4 coating film, had been developed. American physical scientists, A. M. Liu and M. L. Cohen, designed a new kind of inorganic compound C 3N 4 with the theory of molecule engineering. According to calculation, it can reach or even exceed the hardness of diamond, so material scientists and technique circles draw their attention to it. A high speed steel twist drill coated with C 3N 4 film is applied to the drilling hole process on steel workpiece in cutting tests, the tool life is increased greatly. When the C 3N 4 film is coated on the cemented carbide inserts, the cutting performance is improved, but is not good enough. The data of mechanical performance and cutting tests about this kind of new tool material is given in this paper, it shows that C 3N 4 has a promising future. The anti-wear ability of cutting tool increases sharply after C 3N 4 being coated on HSS tool. Coated HSS drill also has some benefit after being reground. The tool life prolongs after C 3N 4 being coated on cemented carbide inserts, but is not so long as that of C 3N 4 coated HSS tool. When machining PRCM with C 3N 4 thin-film coated cemented carbide tool, the cutting performance is poor and it is much better when machining PRCM with PCBN, PCD compound plates and CVD thick-film coated cutting tool. Some relative aspects need to be deeply discussed and researched, e.g. the existing coating techniques is not good enough and should be improved in the future, the film thickness should be optimized and try to find out the most effective value, the binding force and mutual effect between coated film and substrate need to be studied furtherly, etc.
文摘High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.
文摘This work was carried out with the aim of using alloying and ageing processes to develop new alloys from grey cast iron that will have optimum properties suitable for the manufacturing of machine cutting tools. Four different alloys of grey cast iron with alloying composition of Fe-3% Al-2.5% Cr-2% Mo;Fe-3% Al-2% Cr-2% Mo;Fe-3% Al-2.5% Cr-1.5% Mo and Fe-3% Al-1.5% Cr-2% Mo were produced. The chemical analysis of both as-received base metal and produced alloys was determined using Spetro-CJRO Arc-Spectrometer. The microstructural properties and mechanical properties (hardness, impact toughness and ultimate tensile strength) of the produced alloys were determined for both as-cast samples and aged samples. The results showed that the addition of these alloying elements slightly decreased carbon, silicon and phosphorus content and thereby changed the hypereutectic cast iron to hypoeutectic by reducing the carbon equivalent. Also the morphology of graphite flake was changed as a result of the formation of nitrides and carbides of different phases. The results of the mechanical properties showed that the maximum hardness values obtained for each of the four alloys produced and aged at 300?C are 71.5 HRc, 69 HRc, 66.5 HRc and 65.4 HRc respectively. The maximum values for impact toughness obtained for each of the same produced alloys are 66 J, 63.6 J, 62 J and 60.3 J respectively. Also the maximum ultimate tensile strength values obtained for each of the alloys are 1380 N·mm-2, 1311 N·mm-2, 1260 N·mm-2 and 1190 N·mm-2. Comparing the properties obtained from the produced alloys with those of the commercial cutting tools, it was found that cutting tools manufactured from these produced alloys can compete favourably with cast cobalt tool, high speed steel (HSS) and tool steel.
文摘Wear of cutting tools is a big concern for industrial manufacturers, because of their acquisition cost as well as the impact on the production lines when they are unavailable. Law of wear is very important in determining cutting tools lifespan, but most of the existing models don’t take into account the cutting temperature. In this work, the theoretical and experimental results of a dynamic study of metal machining against cutting temperature of a treated steel of grade S235JR with a high-speed steel tool are provided. This study is based on the analysis of two complementary approaches, an experimental approach with the measurement of the temperature and on the other hand, an approach using modeling. Based on unifactorial and multifactorial tests (speed of cut, feed, and depth of cut), this study allowed the highlighting of the influence of the cutting temperature on the machining time. To achieve this objective, two specific approaches have been selected. The first was to measure the temperature of the cutting tool and the second was to determine the wear law using Rayleigh-Ham dimensional analysis method. This study permitted the determination of a law that integrates the cutting temperature in the calculations of the lifespan of the tools during machining.
基金the China Postdoctoral Science Foundation(No.2024M754169)Fundamentals of Equipment Technology(No.2212W22002)for the support of this work。
文摘Micro diamond tools are indispensable for the efficient machining of microstructured surfaces.The precision in tool manufacturing and cutting performance directly determines the processing quality of components.The manufacturing of high-quality micro diamond tools relies on scientific design methods and appropriate processing techniques.However,there is currently a lack of systematic review on the design and manufacturing methods of micro diamond tools in academia.This study systematically summarizes and analyzes modern manufacturing methods for micro diamond tools,as well as the impact of tool waviness,sharpness,and durability on machining quality.Subsequently,a design method is proposed based on the theory of cutting edge strength distribution to enhance tool waviness,sharpness,and durability.Finally,this paper presents current technical challenges faced by micro diamond tools along with potential future solutions to guide scientists in this field.The aim of this review is to contribute to the further development of the current design and manufacturing processes for micro diamond cutting tools.
文摘In spite of the considerable progress made in the domain of the sciences of materials, cutting tools subjected to an intense abrasive wear and a very high temperature of edge. They record during their use an reduced working life. The operations of machining on lathe are regularly stopped for replacing these tools, which influences enormously the production process. Indeed, the search the new materials of substitution, remain a domain very coveted, owing to the fact, it belongs to one stake very significant industrial, in particular, in the mechanical domain and its varied sectors. The recourse to the thermal treatments traditional, limiting in an interval, reduces the wear and the excessive consumption of these cutting tools, but the principal concern of the experts and researchers, in the domain of the mechanical engineering, remain posed. The goal of this study is the introduction of the technique of plasmas, as physical phenomenon, for making material of coating at base of titanium nitrides doped at iron, at the different concentrations. To this objective, one magnetron sputtering with plasma was used for the realization of the coatings deposed on the active parts of the cutting tools. During the experimentation, it was noted that the cutting tools which are treated by plasma, subjected to the machining operations on lathe and the hardness tests, presents one improvement of their hardness and a remarkable increase in their lifespan.
