As the protective component,steel plate had attracted extensive attention because of frequently threats of explosive loads.In this paper,the evolution of microstructure and the mechanism of damage in the quasi-crackin...As the protective component,steel plate had attracted extensive attention because of frequently threats of explosive loads.In this paper,the evolution of microstructure and the mechanism of damage in the quasi-cracking area of steel plate subjected to explosive load were discussed and the relationships between micro defects and dynamic mechanical response were revealed.After the explosion experiment,five observation points were selected equidistant from the quasi-cracking area of the section of the steel plate along the thickness direction,and the characteristics of micro defects at the observation points were analyzed by optical microscope(OM),scanning electron microscope(SEM) and electron backscattered diffraction(EBSD).The observation result shows that many slip bands(SBs) appeared,and the grain orientation changed obviously in the steel plate,the two were the main damage types of micro defects.In addition,cracks,peeling pits,grooves and other lager micro defects were appeared in the lower area of the plate.The stress parameters of the observation points were obtained through an effective numerical model.The mechanism of damage generation and crack propagation in the quasicracking area were clarified by comparing the specific impulse of each observation point with the corresponding micro defects.The result shows that the generation and expansion of micro defects are related to the stress area(i.e.the upper compression area,the neutral plane area,and the lower tension area).The micro defects gather and expand at the grain boundary,and will become macroscopic damage under the continuous action of tensile stress.Besides,the micro defects at the midpoint of the section of the steel plate in the direction away from the explosion center(i.e.the horizontal direction) were also studied.It was found that the specific impulse at these positions were much smaller than that in the thickness direction,the micro defects were only SBs and a few micro cracks,and the those decreased with the increase of the distance from the explosion center.展开更多
Nickel-based single crystal superalloys have become the main structural materials of the aero-engines due to excellent high-temperature strength.The micro defects evolution of nickel-based single crystal superalloys u...Nickel-based single crystal superalloys have become the main structural materials of the aero-engines due to excellent high-temperature strength.The micro defects evolution of nickel-based single crystal superalloys under shear deformation was investigated by molecular dynamics(MD)simulations in the present study.It is found that the interfacial dislocations decompose into Shockley dislocations under low shear stress,resulting in the plastic deformation of the Ni phase.The initial plastic deformation of the Ni3Al phase is caused by Shockley dislocations cutting into the Ni3Al phase.The following deformation from low temperature to medium temperature is controlled by dislocation slip,but the deformation at high temperature is changed.It is also found that the microvoid evolution can be divided into void growth and coalescence during shear deformation.The microvoid could prevent dislocation entanglement,accelerate dislocation decomposition,and promote earlier plastic deformation under relatively low temperatures.展开更多
As the basic protective element, steel plate had attracted world-wide attention because of frequent threats of explosive loads. This paper reports the relationships between microscopic defects of Q345 steel plate unde...As the basic protective element, steel plate had attracted world-wide attention because of frequent threats of explosive loads. This paper reports the relationships between microscopic defects of Q345 steel plate under the explosive load and its macroscopic dynamics simulation. Firstly, the defect characteristics of the steel plate were investigated by stereoscopic microscope(SM) and scanning electron microscope(SEM). At the macroscopic level, the defect was the formation of cave which was concentrated in the range of 0-3.0 cm from the explosion center, while at the microscopic level, the cavity and void formation were the typical damage characteristics. It also explains that the difference in defect morphology at different positions was the combining results of high temperature and high pressure. Secondly, the variation rules of mechanical properties of steel plate under explosive load were studied. The Arbitrary Lagrange-Euler(ALE) algorithm and multi-material fluid-structure coupling method were used to simulate the explosion process of steel plate. The accuracy of the method was verified by comparing the deformation of the simulation results with the experimental results, the pressure and stress at different positions on the surface of the steel plate were obtained. The simulation results indicated that the critical pressure causing the plate defects may be approximately 2.01 GPa. On this basis, it was found that the variation rules of surface pressure and microscopic defect area of the Q345 steel plate were strikingly similar, and the corresponding mathematical relationship between them was established. Compared with Monomolecular growth fitting models(MGFM) and Logistic fitting models(LFM), the relationship can be better expressed by cubic polynomial fitting model(CPFM). This paper illustrated that the explosive defect characteristics of metal plate at the microscopic level can be explored by analyzing its macroscopic dynamic mechanical response.展开更多
This study aimed to utilize micro-computed tomography （micro-CT） analysis to compare new bone formation in rat calvarial defects using chitosan/fibroin-hydroxyapatite （CFB-HAP） or collagen （Bio-Gide） membranes. ...This study aimed to utilize micro-computed tomography （micro-CT） analysis to compare new bone formation in rat calvarial defects using chitosan/fibroin-hydroxyapatite （CFB-HAP） or collagen （Bio-Gide） membranes. Fifty-four （54） rats were studied. A circular bony defect （8 mm diameter） was formed in the centre of the calvaria using a trephine bur. The CFB-HAP membrane was prepared by thermally induced phase separation. In the experimental group （n= 18）, the CFB-HAP membrane was used to cover the bony defect, and in the control group （n= 18）, a resorbable collagen membrane （Bio-Gide） was used. In the negative control group （n= 18）, no membrane was used. In each group, six animals were euthanized at 2, 4 and 8 weeks after surgery. The specimens were then analysed using micro-CT. There were significant differences in bone volume （BV） and bone mineral density （BMD） （P〈O.05） between the negative control group and the membrane groups. However, there were no significant differences between the CFB-HAP group and the collagen group. We concluded that the CFB-HAP membrane has significant potential as a guided bone regeneration （GBR） membrane.展开更多
目的采用微焦点断层扫描(Micro-CT)评价超声骨焊接技术应用过程中超声震荡产热作用下PDLLA材料对骨愈合性能的影响。方法选择SPF级雄性新西兰大白兔36只,随机分为超声骨焊接技术辅助PDLLA材料组(A组)、拧入技术辅助PDLLA材料组(B组)、...目的采用微焦点断层扫描(Micro-CT)评价超声骨焊接技术应用过程中超声震荡产热作用下PDLLA材料对骨愈合性能的影响。方法选择SPF级雄性新西兰大白兔36只,随机分为超声骨焊接技术辅助PDLLA材料组(A组)、拧入技术辅助PDLLA材料组(B组)、假手术组(C组)、空白对照组(D组),各9只。于术后4、8、12周取下颌骨标本,周围骨组织进行HE染色,观察各组植入钉周围情况。对术后4、8、12周的下颌骨大体标本拍摄Micro-CT图,使用VG Studio MAX软件进行三维重建,摆正数据样本,即颌骨颊侧造模处为轴向,动态分析植入钉体积、植入钉周围200μm环状区及骨缺损处的植入材料体积数、相对骨体积分数(BV/TV)、骨小梁厚度(Tb.Th)、骨小梁数(Tb.N)、骨小梁间隙(Tb.Sp)等骨愈合相关指标。结果HE染色结果显示,按3个时间可动态观察到A、B、C组骨缺损处骨性骨痂替代纤维性骨痂,形成类骨质,编织骨的过程符合正常骨损伤愈合的过程。Micro-CT结果显示,A、B组术后3个时间点的材料体积比较差异均无统计学意义(P>0.05);在3个时间点,4组植入钉周围200μm环状区中BV/TV、Tb.Th、Tb.N、Tb.Sp比较差异均无统计学意义(P>0.05);在骨缺损处,A、B、C组三个时间点BV/TV、Tb.Th、Tb.N、Tb.Sp比较差异无统计学意义(P>0.05);术后4周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.N、Tb.Sp差异有统计学意义(P<0.05);与C组比较,A、B组Tb.N差异有统计学意义(P<0.01)。术后8周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.N、Tb.Sp差异有统计学意义(P<0.05);术后12周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.Sp差异有统计学意义(P<0.05)。结论超声骨焊接技术其超声震荡产热作用下PDLLA材料对骨愈合性能无不良影响。展开更多
Centrifugal casting is a foundry process allowing the production of near net-shaped axially symmetrical components. The present study focuses on the microstructural characterization of centrifugally cast alloys featur...Centrifugal casting is a foundry process allowing the production of near net-shaped axially symmetrical components. The present study focuses on the microstructural characterization of centrifugally cast alloys featuring different chemical compositions for the construction of spheres applied in valves made of alloy IN625 for operation at high pressure. Control of the solidification microstructure is needed to assure the reliability of the castings. Actually, a Ni-base superalloy such as this one should have an outstanding combination of mechanical properties, high temperature stability and corrosion resistance. Alloys such as IN625 are characterised by a large amount of alloying elements and a wide solidification range, so they can be affected by micro-porosity defects, related to the shrinkage difference between the matrix and the secondary reinforcing phases(Nb-rich carbides and Laves phase). In this study, the microstructure characterization was performed as a function of the applied heat treatments and it was coupled with a calorimetric analysis in order to understand the mechanism ruling the formation of micro-porosities that can assure alloy soundness. The obtained results show that the presence of micro-porosities is governed by morphology and by the size of the secondary phases, and the presence of the observed secondary phases is detrimental to corrosion resistance.展开更多
基金supported by the Science and Technology Project of Fire Rescue Bureau of Ministry of Emergency Management (Grant No.2022XFZD05)S&T Program of Hebei(Grant No.22375419D)National Natural Science Foundation of China (Grant No.11802160)。
文摘As the protective component,steel plate had attracted extensive attention because of frequently threats of explosive loads.In this paper,the evolution of microstructure and the mechanism of damage in the quasi-cracking area of steel plate subjected to explosive load were discussed and the relationships between micro defects and dynamic mechanical response were revealed.After the explosion experiment,five observation points were selected equidistant from the quasi-cracking area of the section of the steel plate along the thickness direction,and the characteristics of micro defects at the observation points were analyzed by optical microscope(OM),scanning electron microscope(SEM) and electron backscattered diffraction(EBSD).The observation result shows that many slip bands(SBs) appeared,and the grain orientation changed obviously in the steel plate,the two were the main damage types of micro defects.In addition,cracks,peeling pits,grooves and other lager micro defects were appeared in the lower area of the plate.The stress parameters of the observation points were obtained through an effective numerical model.The mechanism of damage generation and crack propagation in the quasicracking area were clarified by comparing the specific impulse of each observation point with the corresponding micro defects.The result shows that the generation and expansion of micro defects are related to the stress area(i.e.the upper compression area,the neutral plane area,and the lower tension area).The micro defects gather and expand at the grain boundary,and will become macroscopic damage under the continuous action of tensile stress.Besides,the micro defects at the midpoint of the section of the steel plate in the direction away from the explosion center(i.e.the horizontal direction) were also studied.It was found that the specific impulse at these positions were much smaller than that in the thickness direction,the micro defects were only SBs and a few micro cracks,and the those decreased with the increase of the distance from the explosion center.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52175306,52205347)the Natural Science Foundation of Shandong Province(Grant No.ZR2021QE181)the China Postdoctoral Science Foundation(Grant No.2022M712432)。
文摘Nickel-based single crystal superalloys have become the main structural materials of the aero-engines due to excellent high-temperature strength.The micro defects evolution of nickel-based single crystal superalloys under shear deformation was investigated by molecular dynamics(MD)simulations in the present study.It is found that the interfacial dislocations decompose into Shockley dislocations under low shear stress,resulting in the plastic deformation of the Ni phase.The initial plastic deformation of the Ni3Al phase is caused by Shockley dislocations cutting into the Ni3Al phase.The following deformation from low temperature to medium temperature is controlled by dislocation slip,but the deformation at high temperature is changed.It is also found that the microvoid evolution can be divided into void growth and coalescence during shear deformation.The microvoid could prevent dislocation entanglement,accelerate dislocation decomposition,and promote earlier plastic deformation under relatively low temperatures.
基金Science and Technology Project of Fire Rescue Bureau of Ministry of Emergency Management(Grant No.2022XFZD05)S&T Program of Hebei(Grant No.22375419D)National Natural Science Foundation of China(Grant No.11802160).
文摘As the basic protective element, steel plate had attracted world-wide attention because of frequent threats of explosive loads. This paper reports the relationships between microscopic defects of Q345 steel plate under the explosive load and its macroscopic dynamics simulation. Firstly, the defect characteristics of the steel plate were investigated by stereoscopic microscope(SM) and scanning electron microscope(SEM). At the macroscopic level, the defect was the formation of cave which was concentrated in the range of 0-3.0 cm from the explosion center, while at the microscopic level, the cavity and void formation were the typical damage characteristics. It also explains that the difference in defect morphology at different positions was the combining results of high temperature and high pressure. Secondly, the variation rules of mechanical properties of steel plate under explosive load were studied. The Arbitrary Lagrange-Euler(ALE) algorithm and multi-material fluid-structure coupling method were used to simulate the explosion process of steel plate. The accuracy of the method was verified by comparing the deformation of the simulation results with the experimental results, the pressure and stress at different positions on the surface of the steel plate were obtained. The simulation results indicated that the critical pressure causing the plate defects may be approximately 2.01 GPa. On this basis, it was found that the variation rules of surface pressure and microscopic defect area of the Q345 steel plate were strikingly similar, and the corresponding mathematical relationship between them was established. Compared with Monomolecular growth fitting models(MGFM) and Logistic fitting models(LFM), the relationship can be better expressed by cubic polynomial fitting model(CPFM). This paper illustrated that the explosive defect characteristics of metal plate at the microscopic level can be explored by analyzing its macroscopic dynamic mechanical response.
文摘This study aimed to utilize micro-computed tomography （micro-CT） analysis to compare new bone formation in rat calvarial defects using chitosan/fibroin-hydroxyapatite （CFB-HAP） or collagen （Bio-Gide） membranes. Fifty-four （54） rats were studied. A circular bony defect （8 mm diameter） was formed in the centre of the calvaria using a trephine bur. The CFB-HAP membrane was prepared by thermally induced phase separation. In the experimental group （n= 18）, the CFB-HAP membrane was used to cover the bony defect, and in the control group （n= 18）, a resorbable collagen membrane （Bio-Gide） was used. In the negative control group （n= 18）, no membrane was used. In each group, six animals were euthanized at 2, 4 and 8 weeks after surgery. The specimens were then analysed using micro-CT. There were significant differences in bone volume （BV） and bone mineral density （BMD） （P〈O.05） between the negative control group and the membrane groups. However, there were no significant differences between the CFB-HAP group and the collagen group. We concluded that the CFB-HAP membrane has significant potential as a guided bone regeneration （GBR） membrane.
文摘目的采用微焦点断层扫描(Micro-CT)评价超声骨焊接技术应用过程中超声震荡产热作用下PDLLA材料对骨愈合性能的影响。方法选择SPF级雄性新西兰大白兔36只,随机分为超声骨焊接技术辅助PDLLA材料组(A组)、拧入技术辅助PDLLA材料组(B组)、假手术组(C组)、空白对照组(D组),各9只。于术后4、8、12周取下颌骨标本,周围骨组织进行HE染色,观察各组植入钉周围情况。对术后4、8、12周的下颌骨大体标本拍摄Micro-CT图,使用VG Studio MAX软件进行三维重建,摆正数据样本,即颌骨颊侧造模处为轴向,动态分析植入钉体积、植入钉周围200μm环状区及骨缺损处的植入材料体积数、相对骨体积分数(BV/TV)、骨小梁厚度(Tb.Th)、骨小梁数(Tb.N)、骨小梁间隙(Tb.Sp)等骨愈合相关指标。结果HE染色结果显示,按3个时间可动态观察到A、B、C组骨缺损处骨性骨痂替代纤维性骨痂,形成类骨质,编织骨的过程符合正常骨损伤愈合的过程。Micro-CT结果显示,A、B组术后3个时间点的材料体积比较差异均无统计学意义(P>0.05);在3个时间点,4组植入钉周围200μm环状区中BV/TV、Tb.Th、Tb.N、Tb.Sp比较差异均无统计学意义(P>0.05);在骨缺损处,A、B、C组三个时间点BV/TV、Tb.Th、Tb.N、Tb.Sp比较差异无统计学意义(P>0.05);术后4周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.N、Tb.Sp差异有统计学意义(P<0.05);与C组比较,A、B组Tb.N差异有统计学意义(P<0.01)。术后8周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.N、Tb.Sp差异有统计学意义(P<0.05);术后12周,与D组比较,A、B、C组BV/TV、Tb.Th、Tb.Sp差异有统计学意义(P<0.05)。结论超声骨焊接技术其超声震荡产热作用下PDLLA材料对骨愈合性能无不良影响。
文摘Centrifugal casting is a foundry process allowing the production of near net-shaped axially symmetrical components. The present study focuses on the microstructural characterization of centrifugally cast alloys featuring different chemical compositions for the construction of spheres applied in valves made of alloy IN625 for operation at high pressure. Control of the solidification microstructure is needed to assure the reliability of the castings. Actually, a Ni-base superalloy such as this one should have an outstanding combination of mechanical properties, high temperature stability and corrosion resistance. Alloys such as IN625 are characterised by a large amount of alloying elements and a wide solidification range, so they can be affected by micro-porosity defects, related to the shrinkage difference between the matrix and the secondary reinforcing phases(Nb-rich carbides and Laves phase). In this study, the microstructure characterization was performed as a function of the applied heat treatments and it was coupled with a calorimetric analysis in order to understand the mechanism ruling the formation of micro-porosities that can assure alloy soundness. The obtained results show that the presence of micro-porosities is governed by morphology and by the size of the secondary phases, and the presence of the observed secondary phases is detrimental to corrosion resistance.
