In this article,a graphic design method for broadband Doherty power amplifier(DPA) is proposed based on the basic principle of impedance matching with the help of Smith chart.The proposed graphic method avoids the com...In this article,a graphic design method for broadband Doherty power amplifier(DPA) is proposed based on the basic principle of impedance matching with the help of Smith chart.The proposed graphic method avoids the complex formula derivation in the traditional amplifier circuit design process,and the design process is more simple and intuitive.Besides,it only takes three steps to build the load modulation network(LMN) of two power amplifiers(PA) of the DPA.Besides,a capacitor is used to replace the parasitic parameters of the transistor,and the LMN designed in the two modes is used for exploration and comparison.Further more,the output impedance of the peaking PA is introduced to make the reflection coefficient trajectory on Smith chart lowfrequency dispersion so as to expand the bandwidth of the DPA at the output power back-off(OBO) level.It would not affect the performance of DPA in the saturation(SAT) state.In this way,a broadband DPA can be implemented easily.To validate the proposed design method,a broadband DPA operating from 1.9to 2.6 GHz is designed and measured based on the proposed method.Under the continuous-wave excitation,the fabricated DPA has a 6 dB OBO efficiency of 48%-56% and a SAT efficiency of 64%-73% from 1.75 to 2.45 GHz,and the peak output power is 48.9-49.8 dBm.展开更多
Unlike traditional propeller-driven underwater vehicles,blended-wing-body underwater gliders(BWBUGs)achieve zigzag gliding through periodic adjustments of their net buoyancy,enhancing their cruising capabilities while...Unlike traditional propeller-driven underwater vehicles,blended-wing-body underwater gliders(BWBUGs)achieve zigzag gliding through periodic adjustments of their net buoyancy,enhancing their cruising capabilities while mini-mizing energy consumption.However,enhancing gliding performance is challenging due to the complex system design and limited design experience.To address this challenge,this paper introduces a model-based,multidisciplinary system design optimization method for BWBUGs at the conceptual design stage.First,a model-based,multidisciplinary co-simulation design framework is established to evaluate both system-level and disciplinary indices of BWBUG performance.A data-driven,many-objective multidisciplinary optimization is subsequently employed to explore the design space,yielding 32 Pareto optimal solutions.Finally,a model-based physical system simulation,which represents the design with the largest hyper-volume contribution among the 32 final designs,is established.Its gliding perfor-mance,validated by component behavior,lays the groundwork for constructing the entire system’s digital prototype.In conclusion,this model-based,multidisciplinary design optimization method effectively generates design schemes for innovative underwater vehicles,facilitating the development of digital prototypes.展开更多
This work was focused on the model-based design method of two-axis four-actuator(TAFA) fast steering mirror system(FSM), in order to improve the design efficiency. The structure and operation principle commonality of ...This work was focused on the model-based design method of two-axis four-actuator(TAFA) fast steering mirror system(FSM), in order to improve the design efficiency. The structure and operation principle commonality of normal TAFA FSM were investigated. Based on the structure and the commonality, the conditions of single-axis idea, high-frequency resonance and coupling were modeled gradually. Combining these models, a holonomic system model was established to reflect and predict the performance of TAFA FSM. A model-based design method was proposed based on the holonomic system model. The design flow and design concept of the method were described. In accordance with the method, a TAFA FSM was designed. Simulations and experiments of the FSM were done, and the results of them were compared. The compared results indicate that the holonomic system model can well reflect and predict the performance of TAFA FSM. The bandwidth of TAFA FSM is more than 250 Hz; adjust time is less than 15 ms;overshoot is less than 8%; position accuracy is better than 10 μrad; the FSM prototype can satisfy the requirements.展开更多
The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) metho...The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) method to address these limitations. In the vLEC method, the waverider is directly designed from the preassigned leading edge and the variable shock angle distribution based on the Leading-Edge Cone (LEC) concept. Since the vLEC method is an approximate method, two test waveriders are designed and evaluated using numerical simulations to validate the shock design accuracy and the effectiveness of the vLEC method. The results show that the shocks of the test waveriders coincide well with the preassigned positions. Furthermore, four specifically designed application cases are conducted to analyze the performance benefits of the vLEC waveriders. The results of these cases indicate that, due to their variable shock angle distributions, the vLEC waveriders exhibit higher lift-to-drag ratios and better longitudinal static stability than conventional waveriders. Additionally, the vLEC waveriders demonstrate superior volumetric capacities near the symmetry plane, albeit with a minor decrease in volumetric efficiency.展开更多
This paper proposes a model-based prognostics method that couples the Extended Kalman Filter(EKF) and a new developed linearization method. The proposed prognostics method is developed in the context of fatigue crack ...This paper proposes a model-based prognostics method that couples the Extended Kalman Filter(EKF) and a new developed linearization method. The proposed prognostics method is developed in the context of fatigue crack propagation in fuselage panels where the model parameters are unknown and the crack propagation is affected by different types of uncertainties. The coupled method is composed of two steps. The first step employs EKF to estimate the unknown model parameters and the current damage state. In the second step, the proposed efficient linearization method is applied to compute analytically the statistical distribution of the damage evolution path in some future time. A numerical case study is implemented to evaluate the performance of the proposed method. The results show that the coupled EKF-linearization method provides satisfactory results: the EKF algorithm well identifies the model parameters, and the linearization method gives comparable prediction results to Monte Carlo(MC) method while leading to very significant computational cost saving. The proposed prognostics method for fatigue crack growth can be used for developing predictive maintenance strategy for an aircraft fleet, in which case, the computational cost saving is significantly meaningful.展开更多
The big-tapered profiled ring disk is a key component of engines for rockets and missiles.A new forming technology,as called spinning-rolling process,has been proposed previously for the high performance,high efficien...The big-tapered profiled ring disk is a key component of engines for rockets and missiles.A new forming technology,as called spinning-rolling process,has been proposed previously for the high performance,high efficiency and low-cost manufacturing of the component.Blank design is the key part of plastic forming process design.For spinning-rolling process,the shape and size of the blank play a crucial role in process stability,deformation behavior and dimensional accuracy.So this work proposes a blank design method to determine the geometry structure and sizes of the blank.The mathematical model for calculating the blank size has been deduced based on volume conservation and neutral layer length invariance principle.The FE simulation and corresponding trial production of an actual big-tapered profiled ring disk show that the proposed blank design method is applicative.In order to obtain a preferred blank,the influence rules of blank size determined by different deformation degrees(rolling ratio k)on the spinning-rolling process are revealed by comprehensive FE simulations.Overall considering the process stability,circularity of the deformed ring disk and forming forces,a reasonable range of deformation degree(rolling ratio k)is recommended for the blank design of the new spinning-rolling process.展开更多
The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt suppo...The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt support is very important to the safety control of surrounding rock as a common support means.The control mechanism and design method of bolt support for shallow-buried large-span caverns is carried out.The calculation method of bolt prestress and length based on arched failure and collapsed failure mode is established.The influence mechanism of different influencing factors on the bolt prestress and length is clarified.At the same time,the constant resistance energy-absorbing bolt with high strength and high toughness is developed,and the comparative test of mechanical properties is carried out.On this basis,the design method of high prestressed bolt support for shallow-buried large-span caverns is put forward,and the field test is carried out in Qingdao metro station in China.The monitoring results show that the maximum roof settlement is 6.8 mm after the new design method is adopted,and the effective control of the shallow-buried large-span caverns is realized.The research results can provide theoretical and technical support for the safety control of shallow-buried large-span caverns.展开更多
Variable Cycle Engine(VCE)serves as the core system in achieving future advanced fighters with cross-generational performance and mission versatility.However,the resultant complex configuration and strong coupling of ...Variable Cycle Engine(VCE)serves as the core system in achieving future advanced fighters with cross-generational performance and mission versatility.However,the resultant complex configuration and strong coupling of control parameters present significant challenges in designing acceleration and deceleration control schedules.To thoroughly explore the performance potential of engine,a global integration design method for acceleration and deceleration control schedule based on inner and outer loop optimization is proposed.The outer loop optimization module employs Integrated Surrogate-Assisted Co-Differential Evolutionary(ISACDE)algorithm to optimize the variable geometry adjustment laws based on B-spline curve,and the inner loop optimization module adopts the fixed-state method to design the open-loop fuel–air ratio control schedules,which are aimed at minimizing the acceleration and deceleration time under multiple constraints.Simulation results demonstrate that the proposed global integration design method not only furthest shortens the acceleration and deceleration time,but also effectively safeguards the engine from overlimit.展开更多
The Nei's improved genetic distance(DA)and gene flow(Nm)were measured using sixteen microsatellite markers.Dendograms based on DA genetic distance using the neighbor-joining(NJ)method and STRUCTURE program were co...The Nei's improved genetic distance(DA)and gene flow(Nm)were measured using sixteen microsatellite markers.Dendograms based on DA genetic distance using the neighbor-joining(NJ)method and STRUCTURE program were constructed to analyze the genetic structure and relationship among 10 Chinese indigenous chicken breeds.The results showed that dendograms of DA genetic distance using the NJ method divided the 10 chicken breeds into two main clusters;one consisted of breeds of low weight body(CHA,TTB,XIA,GUS and BAI),the other contained heavier breeds(LAN,DAG,YOU,XIS and LUY).In the lighter breeds,TIB and CHA clustered together,as did XIA and GUS.In the heavier breeds,XIS and LUY was clustered together in one branch,but LAN,DAG and YOU clustered in independent branches.The results were consistent with Nm estimates among the 10 indigenous chicken breeds.The STRUCTURE program properly inferred the presence of genetic structure despite not pre-defining the origin of individuals.The genetic cluster inferred by STRUCTURE was basically the same as that from the DA distance clustering method.An advantage of the STRUCTURE program was its ability to identify the migrants and admixed individuals in the 10 chicken populations;this could not be achieved by use of the DA distance clustering method.展开更多
With the raising complexity of modern civil aircraft,both academy and industry have shown strong interests on MBSE(Model-Based System Engineering).However,following the application of MBSE,the duration of the design p...With the raising complexity of modern civil aircraft,both academy and industry have shown strong interests on MBSE(Model-Based System Engineering).However,following the application of MBSE,the duration of the design phase exceeded expectations.This paper conducted a survey to the relevant participants involved in the design,revealed that a lack of proper process management is a critical issue.The current MBSE methodology does not provide clear guidelines for monitoring,controlling,and managing processes,which are crucial for both efficiency and effectiveness.To address this,the present paper introduced an improved Process Model(PM)within the MBSE framework for civil aircraft design.This improved model incorporates three new Management Blocks(MB):Progress Management Block(PMB),Review Management Block(RMB),and Configuration Management Block(CMB),developed based on the Capability Maturity Model Integration(CMMI).These additions aim to streamline the design process and better align it with engineering practices.The upgraded MBSE method with the improved PM offers a more structured approach to manage complex aircraft design projects,and a case study is conducted to validate its potential to reduce timelines and enhance overall project outcomes.展开更多
The quasi-rectangular tunnel represents a novel cross-section design,intended to supersede the traditional circular and rectangular tunnel formats.Due to the limited capacity of the tunnel vault to withstand vertical ...The quasi-rectangular tunnel represents a novel cross-section design,intended to supersede the traditional circular and rectangular tunnel formats.Due to the limited capacity of the tunnel vault to withstand vertical loads,an interior column is often installed at the center to enhance its load-bearing capacity.This study aims to develop a hyperstatic reaction method(HRM)for the analysis of deformation and structural integrity in this specific tunnel type.The computational model is validated through comparison with the corresponding finite element method(FEM)analysis.Following comprehensive validation,an ensemble machine learning(ML)model is proposed,using numerical benchmark data,to facilitate real-time design and optimization.Subsequently,three widely used ensemble models,i.e.random forest(RF),gradient boosting decision tree(GBDT),and extreme gradient boosting(XGBoost)are compared to identify the most efficient ML model for replacing the HRM model in the design optimization process.The performance metrics,such as the coefficient of determination R2 of about 0.999 and the mean absolute percentage error(MAPE)of about 1%,indicate that XGBoost outperforms the others,exhibiting excellent agreement with the HRM analysis.Additionally,the model demonstrates high computational efficiency,with prediction times measured in seconds.Finally,the HRM-XGBoost model is integrated with the well-known particle swarm optimization(PSO)for the real-time design optimization of quasi-rectangular tunnels,both with and without the interior column.A feature importance assessment is conducted to evaluate the sensitivity of design input features,enabling the selection of the most critical features for the optimization task.展开更多
Radiative cooling passively emits heat to outer space without energy input,offering promise for energy-efficient thermal management.It is an important solution to promote the low-carbon environmental protection strate...Radiative cooling passively emits heat to outer space without energy input,offering promise for energy-efficient thermal management.It is an important solution to promote the low-carbon environmental protection strategy.With the continuous development of radiative cooling technologies,the material selection,preparation process,structural design,and applica-tion fields have also made more diverse progress.Therefore,this review aims to systematically introduce the fundamental concepts and underlying principles of radiative cooling.A summary of the commonly used materials for radiative cooling is provided.In addition,the advanced fabrication processes and structural designs of radiative cooling materials are further explored and discussed.Subsequently,the unique functions of radiative cooling materials are highlighted to enhance their applicability and usefulness across various fields.An overview of combining radiative cooling materials with different fields is also provided.In reality,these applications hold the potential to improve thermal management across a range of fields.Finally,it summarizes the shortcomings and great potential of radiative cooling materials in various fields.It also looks forward to the future,aiming to promote the progress and widespread adoption of radiative cooling technologies.展开更多
Design for modem engineering system is becoming multidisciplinary and incorporates practical uncertainties; therefore, it is necessary to synthesize reliability analysis and the multidisciplinary design optimization ...Design for modem engineering system is becoming multidisciplinary and incorporates practical uncertainties; therefore, it is necessary to synthesize reliability analysis and the multidisciplinary design optimization （MDO） techniques for the design of complex engineering system. An advanced first order second moment method-based concurrent subspace optimization approach is proposed based on the comparison and analysis of the existing multidisciplinary optimization techniques and the reliability analysis methods. It is seen through a canard configuration optimization for a three-surface transport that the proposed method is computationally efficient and practical with the least modification to the current deterministic optimization process.展开更多
Urban rain-caused floods can not be well resolved with rising urban problem. Hence, construction of sponge park is born at the right moment. The research reviewed the concept, content and value of sponge parks and pro...Urban rain-caused floods can not be well resolved with rising urban problem. Hence, construction of sponge park is born at the right moment. The research reviewed the concept, content and value of sponge parks and proposed theory and principle of landscape design in order to seek the method of landscape design of sponge parks, improve urban eco-environment and advance harmony development between human and nature.展开更多
A new reliability-based multidisciplinary design optimization （RBMDO） framework is proposed by combining the single-loop-based reliability analysis （SLBRA） method with multidisciplinary feasible （MDF） method. Th...A new reliability-based multidisciplinary design optimization （RBMDO） framework is proposed by combining the single-loop-based reliability analysis （SLBRA） method with multidisciplinary feasible （MDF） method. The Kriging approximate model with updating is introduced to reduce the computational cost of MDF caused by the complex structure. The computational efficiency is remarkably improved as the lack of iterative process during reliability analysis. Special attention is paid to a turbine blade design optimization by adopting the proposed method. Results show that the method is much more efficient than the commonly used double-loop based RBMDO method. It is feasible and efficient to apply the method to the engineering design.展开更多
The shape optimization is studied by adopting the domain integrated method which is based on the calculus of variations during the shape design sensitivity analysis. A new method of improving the efficiency of the de...The shape optimization is studied by adopting the domain integrated method which is based on the calculus of variations during the shape design sensitivity analysis. A new method of improving the efficiency of the design velocity field analysis and the quality of the finite element method (FEM) mesh is put forward. The sensitivity analysis which is based on the calculus of variations is used in the shape optimization. The design velocity field is solved by Herrmann method. An example shows that both the quality of the FEM mesh and the efficiency of the computing of the design velocity field are improved by Herrmann method. So the effect and the efficiency of the shape optimization are guaranteed. If using sensitivity analysis which is based on the calculus of variations in the shape optimization, the sensitivity analysis can be a relatively independent module. The efficiency of computing the design velocity field and the quality of mesh will be improved by using Herrmann method.展开更多
Deterministic optimization methods are combined with the Pareto front concept to solve multi-criterion design problems. The algorithm and the numerical implementation are applied to aerodynamic designs. Evolutionary a...Deterministic optimization methods are combined with the Pareto front concept to solve multi-criterion design problems. The algorithm and the numerical implementation are applied to aerodynamic designs. Evolutionary algorithms （EAs） and the Pareto front concept are used to solve practical design problems in industry for its robustness in capturing convex, concave, discrete or discontinuous Pareto fronts of multi-objective optimization problems. However, the process is time-consuming. Therefore, deterministic optimization methods are introduced to capture the Pareto front, and the types of the captured Pareto front are explained. Numerical experiments show that the deterministic optimization method is a good alternative to EAs for capturing any convex and some concave Pareto fronts in multi-criterion aerodynamic optimization problems due to its efficiency.展开更多
This article is based on the theory of foreign language course design. It mainly introduces and analyzes the methods and mode of foreign language design and also integrates with the practice of foreign language teachi...This article is based on the theory of foreign language course design. It mainly introduces and analyzes the methods and mode of foreign language design and also integrates with the practice of foreign language teaching, the author thinks a competent foreign language teacher should not only be satisfied with inculcating ready-made knowledge, but they should also constantly foster the ability of blazing new trails and try to grasp the theory and methods of course design ,and try to carry out course design according to practice and try to give play to their teaching personality and creativity and to have a bold try and exploration and try to improve the foreign language course and foreign language teaching.展开更多
Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing e...Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing efficiency and simplified programming. Both the dual convex programming method and perimeter constraint scheme are used to optimize the 2D and 3D microstructures. Numerical results indicate that the strain energy-based method has the same effectiveness as that of homogenization method for orthotropic materials.展开更多
A microwave-H202 process for sludge pretreatment exhibited high efticiencies of releasing organics, nitrogen, and phosphorus, but large quantifies of H202 residues were detected. A uniform design method was thus emplo...A microwave-H202 process for sludge pretreatment exhibited high efticiencies of releasing organics, nitrogen, and phosphorus, but large quantifies of H202 residues were detected. A uniform design method was thus employed in this study to further optimize H202 dosage by investigating effects of pH and H202 dosage on the amount of 1-I202 residue and releases of organics, nitrogen, and phosphorus. A regression model was established with pH and H202 dosage as the independent variables, and H202 residue and releases of organics, nitrogen, and phosphorus as the dependent variables. In the optimized microwave-H202 process, the pH value of the sludge was firstly adjusted to 11.0, then the sludge was heated to 80~C and H202 was dosed at a H202 ：mixed liquor suspended solids （MLSS） ratio of 0.2, and the sludge was finally heated to 100~C by microwave irradiation. Compared to the microwave-H202 process without optimization, the H202 dosage and the utilization rate of H202 in the optimized microwave-H202 process were reduced by 80% and greatly improved by 3.87 times, respectively, when the H202：MLSS dosage ratio was decreased from 1.0 to 0.2, resulting in nearly the same release rate of soluble chemical oxygen demand in the microwave-H202 process without optimization at H202：MLSS ratio of 0.5.展开更多
基金National Natural Science Foundation of China (No. 62001061)。
文摘In this article,a graphic design method for broadband Doherty power amplifier(DPA) is proposed based on the basic principle of impedance matching with the help of Smith chart.The proposed graphic method avoids the complex formula derivation in the traditional amplifier circuit design process,and the design process is more simple and intuitive.Besides,it only takes three steps to build the load modulation network(LMN) of two power amplifiers(PA) of the DPA.Besides,a capacitor is used to replace the parasitic parameters of the transistor,and the LMN designed in the two modes is used for exploration and comparison.Further more,the output impedance of the peaking PA is introduced to make the reflection coefficient trajectory on Smith chart lowfrequency dispersion so as to expand the bandwidth of the DPA at the output power back-off(OBO) level.It would not affect the performance of DPA in the saturation(SAT) state.In this way,a broadband DPA can be implemented easily.To validate the proposed design method,a broadband DPA operating from 1.9to 2.6 GHz is designed and measured based on the proposed method.Under the continuous-wave excitation,the fabricated DPA has a 6 dB OBO efficiency of 48%-56% and a SAT efficiency of 64%-73% from 1.75 to 2.45 GHz,and the peak output power is 48.9-49.8 dBm.
基金supported by the Postdoctoral Fellowship Program of CPSF(Grant No.GZC20242194)the National Natural Science Foundation of China(Grant Nos.52175251 and 52205268)+1 种基金the Industry Key Technology Research Fund Project of Northwestern Polytechnical University(Grant No.HYGJXM202318)the National Basic Scientific Research Program(Grant No.JCKY2021206B005).
文摘Unlike traditional propeller-driven underwater vehicles,blended-wing-body underwater gliders(BWBUGs)achieve zigzag gliding through periodic adjustments of their net buoyancy,enhancing their cruising capabilities while mini-mizing energy consumption.However,enhancing gliding performance is challenging due to the complex system design and limited design experience.To address this challenge,this paper introduces a model-based,multidisciplinary system design optimization method for BWBUGs at the conceptual design stage.First,a model-based,multidisciplinary co-simulation design framework is established to evaluate both system-level and disciplinary indices of BWBUG performance.A data-driven,many-objective multidisciplinary optimization is subsequently employed to explore the design space,yielding 32 Pareto optimal solutions.Finally,a model-based physical system simulation,which represents the design with the largest hyper-volume contribution among the 32 final designs,is established.Its gliding perfor-mance,validated by component behavior,lays the groundwork for constructing the entire system’s digital prototype.In conclusion,this model-based,multidisciplinary design optimization method effectively generates design schemes for innovative underwater vehicles,facilitating the development of digital prototypes.
基金Projects(51135009)supported by the National Natural Science Foundation of China
文摘This work was focused on the model-based design method of two-axis four-actuator(TAFA) fast steering mirror system(FSM), in order to improve the design efficiency. The structure and operation principle commonality of normal TAFA FSM were investigated. Based on the structure and the commonality, the conditions of single-axis idea, high-frequency resonance and coupling were modeled gradually. Combining these models, a holonomic system model was established to reflect and predict the performance of TAFA FSM. A model-based design method was proposed based on the holonomic system model. The design flow and design concept of the method were described. In accordance with the method, a TAFA FSM was designed. Simulations and experiments of the FSM were done, and the results of them were compared. The compared results indicate that the holonomic system model can well reflect and predict the performance of TAFA FSM. The bandwidth of TAFA FSM is more than 250 Hz; adjust time is less than 15 ms;overshoot is less than 8%; position accuracy is better than 10 μrad; the FSM prototype can satisfy the requirements.
基金supported by grants from the National Natural Science Foundation of China(No.U20B2006)the Guangdong Basic and Applied Basic Research Foundation(No.2022A1515110145)Young Elite Scientists Sponsorship Program by China Association for Science and Technology(No.2022QNRC001).
文摘The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) method to address these limitations. In the vLEC method, the waverider is directly designed from the preassigned leading edge and the variable shock angle distribution based on the Leading-Edge Cone (LEC) concept. Since the vLEC method is an approximate method, two test waveriders are designed and evaluated using numerical simulations to validate the shock design accuracy and the effectiveness of the vLEC method. The results show that the shocks of the test waveriders coincide well with the preassigned positions. Furthermore, four specifically designed application cases are conducted to analyze the performance benefits of the vLEC waveriders. The results of these cases indicate that, due to their variable shock angle distributions, the vLEC waveriders exhibit higher lift-to-drag ratios and better longitudinal static stability than conventional waveriders. Additionally, the vLEC waveriders demonstrate superior volumetric capacities near the symmetry plane, albeit with a minor decrease in volumetric efficiency.
基金partially funded by the National Natural Science Foundation of China (No.51805262)
文摘This paper proposes a model-based prognostics method that couples the Extended Kalman Filter(EKF) and a new developed linearization method. The proposed prognostics method is developed in the context of fatigue crack propagation in fuselage panels where the model parameters are unknown and the crack propagation is affected by different types of uncertainties. The coupled method is composed of two steps. The first step employs EKF to estimate the unknown model parameters and the current damage state. In the second step, the proposed efficient linearization method is applied to compute analytically the statistical distribution of the damage evolution path in some future time. A numerical case study is implemented to evaluate the performance of the proposed method. The results show that the coupled EKF-linearization method provides satisfactory results: the EKF algorithm well identifies the model parameters, and the linearization method gives comparable prediction results to Monte Carlo(MC) method while leading to very significant computational cost saving. The proposed prognostics method for fatigue crack growth can be used for developing predictive maintenance strategy for an aircraft fleet, in which case, the computational cost saving is significantly meaningful.
基金the National Natural Science Foundation of China(No.52275378)the National Key Laboratory for Precision Hot Processing of Metals(6142909200208)。
文摘The big-tapered profiled ring disk is a key component of engines for rockets and missiles.A new forming technology,as called spinning-rolling process,has been proposed previously for the high performance,high efficiency and low-cost manufacturing of the component.Blank design is the key part of plastic forming process design.For spinning-rolling process,the shape and size of the blank play a crucial role in process stability,deformation behavior and dimensional accuracy.So this work proposes a blank design method to determine the geometry structure and sizes of the blank.The mathematical model for calculating the blank size has been deduced based on volume conservation and neutral layer length invariance principle.The FE simulation and corresponding trial production of an actual big-tapered profiled ring disk show that the proposed blank design method is applicative.In order to obtain a preferred blank,the influence rules of blank size determined by different deformation degrees(rolling ratio k)on the spinning-rolling process are revealed by comprehensive FE simulations.Overall considering the process stability,circularity of the deformed ring disk and forming forces,a reasonable range of deformation degree(rolling ratio k)is recommended for the blank design of the new spinning-rolling process.
基金Project(2023YFC3805700) supported by the National Key Research and Development Program of ChinaProjects(42477166,42277174) supported by the National Natural Science Foundation of China+2 种基金Project(2024JCCXSB01) supported by the Fundamental Research Funds for the Central Universities,ChinaProject(KFJJ24-01M) supported by the State Key Laboratory of Explosion Science and Safety Protection,Beijing Institute of Technology,ChinaProject(HLCX-2024-04) supported by the Open Foundation of Collaborative Innovation Center of Green Development and Ecological Restoration of Mineral Resources,China。
文摘The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt support is very important to the safety control of surrounding rock as a common support means.The control mechanism and design method of bolt support for shallow-buried large-span caverns is carried out.The calculation method of bolt prestress and length based on arched failure and collapsed failure mode is established.The influence mechanism of different influencing factors on the bolt prestress and length is clarified.At the same time,the constant resistance energy-absorbing bolt with high strength and high toughness is developed,and the comparative test of mechanical properties is carried out.On this basis,the design method of high prestressed bolt support for shallow-buried large-span caverns is put forward,and the field test is carried out in Qingdao metro station in China.The monitoring results show that the maximum roof settlement is 6.8 mm after the new design method is adopted,and the effective control of the shallow-buried large-span caverns is realized.The research results can provide theoretical and technical support for the safety control of shallow-buried large-span caverns.
基金supported by the Basic Research on Dynamic Real-time Modeling and Onboard Adaptive Modeling of Aero Engine,China(No.QZPY202308)。
文摘Variable Cycle Engine(VCE)serves as the core system in achieving future advanced fighters with cross-generational performance and mission versatility.However,the resultant complex configuration and strong coupling of control parameters present significant challenges in designing acceleration and deceleration control schedules.To thoroughly explore the performance potential of engine,a global integration design method for acceleration and deceleration control schedule based on inner and outer loop optimization is proposed.The outer loop optimization module employs Integrated Surrogate-Assisted Co-Differential Evolutionary(ISACDE)algorithm to optimize the variable geometry adjustment laws based on B-spline curve,and the inner loop optimization module adopts the fixed-state method to design the open-loop fuel–air ratio control schedules,which are aimed at minimizing the acceleration and deceleration time under multiple constraints.Simulation results demonstrate that the proposed global integration design method not only furthest shortens the acceleration and deceleration time,but also effectively safeguards the engine from overlimit.
基金supported by the Program of National Technological Basis from Ministry of Science and Technology of China(No.2005DKA21101)the National Natural Science Foundation of China(No.30700572)
文摘The Nei's improved genetic distance(DA)and gene flow(Nm)were measured using sixteen microsatellite markers.Dendograms based on DA genetic distance using the neighbor-joining(NJ)method and STRUCTURE program were constructed to analyze the genetic structure and relationship among 10 Chinese indigenous chicken breeds.The results showed that dendograms of DA genetic distance using the NJ method divided the 10 chicken breeds into two main clusters;one consisted of breeds of low weight body(CHA,TTB,XIA,GUS and BAI),the other contained heavier breeds(LAN,DAG,YOU,XIS and LUY).In the lighter breeds,TIB and CHA clustered together,as did XIA and GUS.In the heavier breeds,XIS and LUY was clustered together in one branch,but LAN,DAG and YOU clustered in independent branches.The results were consistent with Nm estimates among the 10 indigenous chicken breeds.The STRUCTURE program properly inferred the presence of genetic structure despite not pre-defining the origin of individuals.The genetic cluster inferred by STRUCTURE was basically the same as that from the DA distance clustering method.An advantage of the STRUCTURE program was its ability to identify the migrants and admixed individuals in the 10 chicken populations;this could not be achieved by use of the DA distance clustering method.
基金supported by the National Natural Science Foundation of China(No.62073267)。
文摘With the raising complexity of modern civil aircraft,both academy and industry have shown strong interests on MBSE(Model-Based System Engineering).However,following the application of MBSE,the duration of the design phase exceeded expectations.This paper conducted a survey to the relevant participants involved in the design,revealed that a lack of proper process management is a critical issue.The current MBSE methodology does not provide clear guidelines for monitoring,controlling,and managing processes,which are crucial for both efficiency and effectiveness.To address this,the present paper introduced an improved Process Model(PM)within the MBSE framework for civil aircraft design.This improved model incorporates three new Management Blocks(MB):Progress Management Block(PMB),Review Management Block(RMB),and Configuration Management Block(CMB),developed based on the Capability Maturity Model Integration(CMMI).These additions aim to streamline the design process and better align it with engineering practices.The upgraded MBSE method with the improved PM offers a more structured approach to manage complex aircraft design projects,and a case study is conducted to validate its potential to reduce timelines and enhance overall project outcomes.
基金funded by the Hanoi University of Mining and Geology(Grant No.T23-44)The research is also funded by the German Research Foundation(DFG e Project number 518862444)in collaboration with the Vietnam National Foundation for Science and Technology Development(NAFOSTED)under grant number DFG.105e2022.03The third author was funded by the Postdoctoral Scholarship Program of the Vingroup Innovation Foundation(VINIF)(VINIF.2023.STS.15).
文摘The quasi-rectangular tunnel represents a novel cross-section design,intended to supersede the traditional circular and rectangular tunnel formats.Due to the limited capacity of the tunnel vault to withstand vertical loads,an interior column is often installed at the center to enhance its load-bearing capacity.This study aims to develop a hyperstatic reaction method(HRM)for the analysis of deformation and structural integrity in this specific tunnel type.The computational model is validated through comparison with the corresponding finite element method(FEM)analysis.Following comprehensive validation,an ensemble machine learning(ML)model is proposed,using numerical benchmark data,to facilitate real-time design and optimization.Subsequently,three widely used ensemble models,i.e.random forest(RF),gradient boosting decision tree(GBDT),and extreme gradient boosting(XGBoost)are compared to identify the most efficient ML model for replacing the HRM model in the design optimization process.The performance metrics,such as the coefficient of determination R2 of about 0.999 and the mean absolute percentage error(MAPE)of about 1%,indicate that XGBoost outperforms the others,exhibiting excellent agreement with the HRM analysis.Additionally,the model demonstrates high computational efficiency,with prediction times measured in seconds.Finally,the HRM-XGBoost model is integrated with the well-known particle swarm optimization(PSO)for the real-time design optimization of quasi-rectangular tunnels,both with and without the interior column.A feature importance assessment is conducted to evaluate the sensitivity of design input features,enabling the selection of the most critical features for the optimization task.
基金National Natural Science Foundation of China Excellent Youth Fund(No.52222509)the Foundation for Innovative Research Groups of the National Natural Science Foundation of China(No.52021003)+3 种基金National Key Research and Development Program of China(No.2018YFA0703300)National Natural Science Foundation of China(No.52105298)Science and Technology Development Program of Jilin Province(No.SKL202402005)"Fundamental Research Funds for the Central Universities".
文摘Radiative cooling passively emits heat to outer space without energy input,offering promise for energy-efficient thermal management.It is an important solution to promote the low-carbon environmental protection strategy.With the continuous development of radiative cooling technologies,the material selection,preparation process,structural design,and applica-tion fields have also made more diverse progress.Therefore,this review aims to systematically introduce the fundamental concepts and underlying principles of radiative cooling.A summary of the commonly used materials for radiative cooling is provided.In addition,the advanced fabrication processes and structural designs of radiative cooling materials are further explored and discussed.Subsequently,the unique functions of radiative cooling materials are highlighted to enhance their applicability and usefulness across various fields.An overview of combining radiative cooling materials with different fields is also provided.In reality,these applications hold the potential to improve thermal management across a range of fields.Finally,it summarizes the shortcomings and great potential of radiative cooling materials in various fields.It also looks forward to the future,aiming to promote the progress and widespread adoption of radiative cooling technologies.
基金National Natural Science Foundation of China (10377015)
文摘Design for modem engineering system is becoming multidisciplinary and incorporates practical uncertainties; therefore, it is necessary to synthesize reliability analysis and the multidisciplinary design optimization （MDO） techniques for the design of complex engineering system. An advanced first order second moment method-based concurrent subspace optimization approach is proposed based on the comparison and analysis of the existing multidisciplinary optimization techniques and the reliability analysis methods. It is seen through a canard configuration optimization for a three-surface transport that the proposed method is computationally efficient and practical with the least modification to the current deterministic optimization process.
文摘Urban rain-caused floods can not be well resolved with rising urban problem. Hence, construction of sponge park is born at the right moment. The research reviewed the concept, content and value of sponge parks and proposed theory and principle of landscape design in order to seek the method of landscape design of sponge parks, improve urban eco-environment and advance harmony development between human and nature.
基金Supported by the National High Technology Research and Development Program of China("863" Program) (2009AA04Z418, 2007AA04Z404)the National "111" Project(B07050)~~
文摘A new reliability-based multidisciplinary design optimization （RBMDO） framework is proposed by combining the single-loop-based reliability analysis （SLBRA） method with multidisciplinary feasible （MDF） method. The Kriging approximate model with updating is introduced to reduce the computational cost of MDF caused by the complex structure. The computational efficiency is remarkably improved as the lack of iterative process during reliability analysis. Special attention is paid to a turbine blade design optimization by adopting the proposed method. Results show that the method is much more efficient than the commonly used double-loop based RBMDO method. It is feasible and efficient to apply the method to the engineering design.
文摘The shape optimization is studied by adopting the domain integrated method which is based on the calculus of variations during the shape design sensitivity analysis. A new method of improving the efficiency of the design velocity field analysis and the quality of the finite element method (FEM) mesh is put forward. The sensitivity analysis which is based on the calculus of variations is used in the shape optimization. The design velocity field is solved by Herrmann method. An example shows that both the quality of the FEM mesh and the efficiency of the computing of the design velocity field are improved by Herrmann method. So the effect and the efficiency of the shape optimization are guaranteed. If using sensitivity analysis which is based on the calculus of variations in the shape optimization, the sensitivity analysis can be a relatively independent module. The efficiency of computing the design velocity field and the quality of mesh will be improved by using Herrmann method.
文摘Deterministic optimization methods are combined with the Pareto front concept to solve multi-criterion design problems. The algorithm and the numerical implementation are applied to aerodynamic designs. Evolutionary algorithms （EAs） and the Pareto front concept are used to solve practical design problems in industry for its robustness in capturing convex, concave, discrete or discontinuous Pareto fronts of multi-objective optimization problems. However, the process is time-consuming. Therefore, deterministic optimization methods are introduced to capture the Pareto front, and the types of the captured Pareto front are explained. Numerical experiments show that the deterministic optimization method is a good alternative to EAs for capturing any convex and some concave Pareto fronts in multi-criterion aerodynamic optimization problems due to its efficiency.
文摘This article is based on the theory of foreign language course design. It mainly introduces and analyzes the methods and mode of foreign language design and also integrates with the practice of foreign language teaching, the author thinks a competent foreign language teacher should not only be satisfied with inculcating ready-made knowledge, but they should also constantly foster the ability of blazing new trails and try to grasp the theory and methods of course design ,and try to carry out course design according to practice and try to give play to their teaching personality and creativity and to have a bold try and exploration and try to improve the foreign language course and foreign language teaching.
基金National Natural Science Foundation of China （90405016, 10676028） 973 Program （2006CB601205）+1 种基金 863 Project （2006AA04Z 122） Aeronautical Science Foundation （04B53080, 2006ZA 53006） and 111 Project （B07050）
文摘Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing efficiency and simplified programming. Both the dual convex programming method and perimeter constraint scheme are used to optimize the 2D and 3D microstructures. Numerical results indicate that the strain energy-based method has the same effectiveness as that of homogenization method for orthotropic materials.
基金supported by the National Natural Science Foundation of China (No. 51008297)the Hi-Tech Research and Development Program (863) of China(No. 2007AA06Z347)the National Major Science & Technology Projects for Water Pollution Control and Management (No. 2012ZX07202-005)
文摘A microwave-H202 process for sludge pretreatment exhibited high efticiencies of releasing organics, nitrogen, and phosphorus, but large quantifies of H202 residues were detected. A uniform design method was thus employed in this study to further optimize H202 dosage by investigating effects of pH and H202 dosage on the amount of 1-I202 residue and releases of organics, nitrogen, and phosphorus. A regression model was established with pH and H202 dosage as the independent variables, and H202 residue and releases of organics, nitrogen, and phosphorus as the dependent variables. In the optimized microwave-H202 process, the pH value of the sludge was firstly adjusted to 11.0, then the sludge was heated to 80~C and H202 was dosed at a H202 ：mixed liquor suspended solids （MLSS） ratio of 0.2, and the sludge was finally heated to 100~C by microwave irradiation. Compared to the microwave-H202 process without optimization, the H202 dosage and the utilization rate of H202 in the optimized microwave-H202 process were reduced by 80% and greatly improved by 3.87 times, respectively, when the H202：MLSS dosage ratio was decreased from 1.0 to 0.2, resulting in nearly the same release rate of soluble chemical oxygen demand in the microwave-H202 process without optimization at H202：MLSS ratio of 0.5.
