This study presents the development of high-performance,solvent-free polyurethane-urea(PU)elastomeric coatings engineered for rapid curing and precise sprayability.Utilizing polyoxytetramethylene glycol(PTMG)as the pr...This study presents the development of high-performance,solvent-free polyurethane-urea(PU)elastomeric coatings engineered for rapid curing and precise sprayability.Utilizing polyoxytetramethylene glycol(PTMG)as the primary polyol and a static-mixing spraying technique,the formulations were systematically optimized.It was found that a soft-segment content of 64% yields optimalmechanical properties,achieving a remarkable tensile strength exceeding 30 MPa.Crucially,the incorporation of an ultra-low concentration(0.002 wt%)of dibutyltin dilaurate catalyst was sufficient to enhance curing completeness and mechanical performance while effectively eliminating moisture-induced foaming,a common challenge in solvent-free spray applications.The gel and tack-free times were successfully reduced to the order of minutes through strategic formulation with the chain extender dimethylsulfidetoluene diamine,minimizing reliance on high catalyst loadings.Theresultant PTMG-based coatings exhibit exceptional comprehensive properties,including a tensile strength>30 MPa,elongation at break>400%,and a tear strength of 66 N/mm,significantly surpassing conventional polypropylene-diamine-based polyurea systems.Furthermore,the coatings demonstrated superior low-temperature flexibility,evidenced by a glass transition temperature of-53℃,and suppressed soft-segment crystallinity.The solvent-free nature and tunable curing kinetics of this system enable precise spraying on complex geometries,effectively overcoming thickness-control limitations for small-object applications.This work establishes a sustainable and high-performance coating solution ideal for demanding impact-and corrosionresistant protective layers.展开更多
Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bott...Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.展开更多
Vat photopolymerization(VPP)3D printing is an optimized technology for complex-shaped ceramic cores,in which the solid loading of ceramic slurries greatly infiuences the microstructure and property of the final cerami...Vat photopolymerization(VPP)3D printing is an optimized technology for complex-shaped ceramic cores,in which the solid loading of ceramic slurries greatly infiuences the microstructure and property of the final ceramic parts.However,the high solid loading of slurries is highly limited by the high viscosity.In this study,silica-based ceramic core slurries with solid loading up to 68vol.%were achieved by the composition design to optimize the performance,considering the curing,rheological,and double bond conversion rate.The slurries demonstrate superior curing and rheological performance with mass ratio of monomers being 3:2 and mass fraction of BYK111 being 4wt.%.Afterwards,the impact of solid loading on the morphology and mechanical properties was investigated.As the solid loading increases,the microstructure becomes gradually dense,leading to an improved flexural strength of 19.5 MPa.Additionally,the sintering shrinkage becomes more uniform,satisfying the casting requirements effectively.This work serves as a guide for the preparation of ceramic slurries with a high solid loading.展开更多
Additive manufacturing(AM)is an innovative technique that enables the flexible design and construction of three-dimensional objects.In the nuclear industry,AM enables the use of advanced materials and high-performance...Additive manufacturing(AM)is an innovative technique that enables the flexible design and construction of three-dimensional objects.In the nuclear industry,AM enables the use of advanced materials and high-performance components.Although AM processing has been extensively investigated,the corresponding mechanical properties and structural integrity issues of AM parts have received less attention.This study reviews the mechanical behavior and key challenges of typical AM materials,fuel components,compact heat exchangers with complex geometries,and additive repair of damaged reactor components.The findings of this review will guide the efficient and reliable implementation of AM techniques in nuclear reactors.展开更多
A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests...A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.展开更多
This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution conc...This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution concentrations of 3%,6%,9%,and 12%,the optimal dispersion effect was achieved with an ultrasonic dispersion time of 20 minutes.Specifically,at a 6%nano-TiO_(2)content,both the workability and mechanical performance of the cement paste were enhanced.Furthermore,while nano-TiO_(2)did not alter the types of hydration products present in the cement paste,it did increase the amount of C-S-H gels.This enhancement was attributed to a higher number of nucleation sites for hydration products,which promoted hydration and reduced the porosity of the cement paste.展开更多
Floating photovoltaic(FPV)technology is emerging as a highly promising approach to accelerate decarbonization of the global economy,due to its higher power generation efficiency and lower land occupation.With the rapi...Floating photovoltaic(FPV)technology is emerging as a highly promising approach to accelerate decarbonization of the global economy,due to its higher power generation efficiency and lower land occupation.With the rapid development of FPV technology,the mechanical performance degradation of key components caused by the harsh marine environment has become a pressing issue,as it significantly contributes to failure behavior observed in FPV systems.A comprehensive compilation of the mechanical performance of key components in FPV systems is also currently unavailable.Here,the mechanical behavior of each structural component in FPV systems under harsh marine environments is systematically reviewed.It further emphasizes the synergistic effects of mechanical performance degradation among different components on the overall system.The drop-off rate(v)of normalized elongation at break(EAB)of polymer under the synergistic effect of various environmental factors increases from 7.5×10^(−4)h^(−1)to 21.8×10^(−4)h^(−1)compared with the single environmental stress.Moreover,the development of novel materials and innovative mechanical structures applied in FPV systems to enhance mechanical performance is discussed.The novel flexible PV modules applied in FPV systems minimize the loads acting on the mooring lines by 80%and increase power generation by 5%.Notably,this paper provides a theoretical foundation for developing standards of FPV systems,especially the establishment of standards related to the synergistic effects of the mechanical performance degradation of different key components on FPV systems.展开更多
To elucidate the yielding performance of compact yielding anchor cables in working state,a yielding mechanical model incorporating extrusion friction and fastening rotation under confining pressure is constructed.The ...To elucidate the yielding performance of compact yielding anchor cables in working state,a yielding mechanical model incorporating extrusion friction and fastening rotation under confining pressure is constructed.The yielding resistance enhancement effect(ω)caused by working environment constraints is evaluated through multi-layer composite sleeve hole expansion analysis,forming a theoretical framework for calculating the working yielding force.Laboratory and in-situ pull-out tests are conducted to determine the yielding performance and validate the analytical theory.The main conclusions are:(1)Yielding force and energy-release capacity increase withω,significantly outperforming the unconfined state.(2)In-situ tests under varying rockmass and geostress conditions(F1–F3)determine the yielding force increases to 183.4–290.1,204.0–290.8,and 235.0–327.1 kN.(3)The slight deviation(–12.5%to 6.2%)between the theoretical and measured yielding force confirms that the analytical theory effectively describes the working yielding performance.(4)ωincreases with higher geostress and improved rock mechanical properties,with initial geostress(σ_(0))and elastic modulus of surrounding rock(E_(3))identified as critical parameters.展开更多
Due to the features and wide range of potential applications,cellulose ionogels are the subject of extensive research.Green celluloses have been employed as a three-dimensional skeleton network to restrict the ionic l...Due to the features and wide range of potential applications,cellulose ionogels are the subject of extensive research.Green celluloses have been employed as a three-dimensional skeleton network to restrict the ionic liquids(ILs)toward advanced ion-conductive ionogels.Diversiform cellulose ionogels with desirable perfor-mances,via physical/chemical reactions between cellulose and ILs,have been harvested,which have the po-tential to emerge as a bright star in the field of flexible electronics,such as sensors,electrolyte materials as power sources,and thermoelectric devices.Herein,a review regarding cellulose ionogels in terms of fundamental types of cellulose,formation strategies and mechanism,and principal properties is presented.Next,the diverse application prospects of cellulose ionogels in flexible electronics have been summarized.More importantly,the future challenges and advancing directions to be explored for cellulose ionogels are discussed.展开更多
Indium(In)has been used as a thermal interface material(TIM1)in high-performance central processing unit(CPU)for better heat dissipation.However,leakage or pump-out of liquid indium during the multiple reflow cycles l...Indium(In)has been used as a thermal interface material(TIM1)in high-performance central processing unit(CPU)for better heat dissipation.However,leakage or pump-out of liquid indium during the multiple reflow cycles limits its application in advanced flip chip ball gray array(FCBGA)packaging.Former researchers place a seal or dam structure to prevent In leakage,leading to the risk of In explosion,thermal degradation,or require additional keep-out zones.In this work,a copper foam(CF)matrix was embedded in In to absorb the liquid In and eliminate the leakage of In TIM1 during the multiple reflow cycles,as the CF capillary force.Au/Ni/Cu-Au/Ni/Cu joint was fabricated by soldering with the composite solder at 190℃for 2 min.After reflow cycles,good metallurgical bonding was formed at interfaces of joint.Rod-like Cu_(11)In_(9) formed at the CF and In interface,due to the re-dissolved of Cu_(11)In_(9) crystal.Small amount of Cu atoms from CF can reduce the activity of In,which inhibits the growth of Ni_(3)In_(7) intermetallic compound(IMC)at the interface of In and Au/Ni/Cu substrate.The CF matrix also improved the shear strength(22.9%)and thermal conductivity of the solder joints.Besides,the fracture behavior of solder joints without CF matrix was classified to be ductile type while that with CF matrix was changed to be ductile-brittle mixed type.展开更多
Currently,as environmental pollution becomes increasingly severe,flue gas denitrification has emerged as a significant area of research.With the advancement of modern industry and the improvement of living standards,a...Currently,as environmental pollution becomes increasingly severe,flue gas denitrification has emerged as a significant area of research.With the advancement of modern industry and the improvement of living standards,air pollution has gained growing attention.Sulfur dioxide and nitrogen oxides(NO_(x))have become major contributors to air pollution,posing serious harm to the environment.Consequently,flue gas desulfurization and denitrification technologies have become key research focuses in industrial development.This paper explores the selection of agricultural waste carbon sources and their pretreatment methods.It provides an in-depth analysis of the significance of agricultural waste carbon sources in flue gas denitrification,focusing on their performance and mechanisms.The study also discusses the role of agricultural waste carbon sources in flue gas denitrification,aiming to offer new research perspectives for relevant stakeholders.展开更多
The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in...The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.展开更多
This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the spa...This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the space spiral curve, a three-dimensional parametrical geometrical model is constructed. The finite element model is built by using the beam-beam contact elements and 3D beam elements. The constituent nitinol wires are assumed to be linear elastic material. The finite element analysis figures out that the radial stiffness of the stent and the stress distribution of the wires are influenced by all the structural parameters. The helix pitch of the wires is the most important factor. Under the condition of the same load and other structural parameters remaining unchanged, when the number of wires is 24, the stress of the wire crosssection is at the minimum. A comparison between the vitro experimental results and the analytical results is conducted, and the data is consistent, which proves that the current finite element model can be used to appropriately predict the mechanical performance of the braided esophageal stents.展开更多
We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptiona...We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptional mechanical performance,including an ideal compressive strength of 343 GPa at a pressure of 300 GPa,~33% higher than that of diamond.This ultrahigh strength arises from the synergistic interplay between its three-dimensional covalent framework and hybridized bonding topology,which enables isotropic stress accommodation and dynamic electronic rearrangement.These results establish cage-N as a promising non-carbon ultrahard material and provide a bonding-driven route toward designing superhard frameworks under extreme conditions.展开更多
The high hydrophilicity of pineapple leaf fibres(PALF)limits their use in cement-and gypsum-based composites exposed to moisture.This study evaluates,for the first time,the combined effect of palm kernel oil and beesw...The high hydrophilicity of pineapple leaf fibres(PALF)limits their use in cement-and gypsum-based composites exposed to moisture.This study evaluates,for the first time,the combined effect of palm kernel oil and beeswax on the hygroscopic resistance and mechanical stability of PALF.The fibres were functionalised with three formulations(oil,wax,and a 1:2 oil/wax blend)applied at different mass ratios(CR=0.5-2).Treatments increased the average bundle diameter by up to+46%(238μm)and reduced density down to 1.06 g/cm^(3).Hygroscopically,water absorption decreased from 202.4%(raw fibres)to 76.3%(CR=2),representing a maximum reduction of 59.4%in saline medium,while moisture regain dropped from 27.9%to 14.6%(−47.7%).The oil/wax blend proved most effective,simultaneously reducing water absorption(−51.2%)and moisture regain(−46.8%)at CR=1.Mechanically,the fibres retained tensile strength(415.2 vs.460.8 MPa,+11%at CR=1)and exhibited enhanced ductility(+62.5%,with elongation at break increasing from 1.6%to 2.6%),without significantly altering Young’s modulus(12.3 to 10 GPa).Water absorption kinetics were accurately described by the Czel and Mohsenin models(R^(2)>0.98).These findings clearly demonstrate that bio-based lipid coatings can provide an eco-friendly alternative to conventional chemical treatments.They improve hygroscopic resistance and preserve mechanical integrity of PALF,providing original quantitative data for their integration into durable cement-and gypsum-based composites subjected to humid or cyclic wet-dry conditions.展开更多
The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evo...The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.展开更多
The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. ...The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. The results show that not only the alloy composition and heat treatment before forming influence the formability, but also they have an effect on the paint bake response of the alloys. Increasing the alloy Si content, decreasing Mg/Si ratio and adding 0.3% Cu （mass fraction） were generally found to improve the tensile ductility and formability of the alloys studied, while pre-ageing was found to decrease these properties. A full property profile of these alloys in terms of strength, tensile ductility, work hardening, strain rate sensitivity, forming limit and paint bake response was presented.展开更多
The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, ...The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, EDS and X-ray diffractometer, the microstructure and phase composition of aluminum rod were measured and analyzed. The results indicate that the content of rare earth element Ce is between 0.05% -0.16% in the aluminum rod for electrical purpose. Its tensile strength is enhanced to some extent. The research also discovers that the tensile strength is enhanced remarkably with impurity element Si content increases. Because influence of Si is big to the conductivity, the Si content should be controlled continuously strictly in the aluminum for electrical purpose. Adding rare earth element Ce reduces the solid solubility of Si in the aluminum matrix, and the negative effect of Si on the aluminum conductor reduces effectively. So the limit of in Si content in aluminum rod for electrical purpose can be relaxed moderately.展开更多
ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performa...ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.展开更多
This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−...This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−xBiCu solder joints were investigated.Bi-doping modified the microstructure of the solder joints by refining the primaryβ-Sn and eutectic phases.Bi-doping below 2 wt.%dissolved in theβ-Sn matrix and formed a solid solution,whereas Bi additions equal to or greater than 2 wt.%formed Bi precipitates in theβ-Sn matrix.Solid solution strengthening and precipitation strengthening mechanisms in theβ-Sn matrix increased the ultimate tensile strength and microhardness of the alloy from 35.7 MPa and 12.6 HV to 55.3 MPa and 20.8 HV,respectively,but elongation decreased from 24.6%to 16.1%.The fracture surface of a solder joint containing 2 wt.%Bi was typical of a brittle failure rather than a ductile failure.The interfacial layer of all solder joints comprised two parallel IMC layers:a layer of Cu6Sn5 and a layer of Cu3Sn.The interfacial layer was thinner and the shear strength was greater in SAC305−xBiCu joints than in SAC305Cu solder joints.Therefore,small addition of Bi refined microstructure,reduced melting temperature and improved the mechanical performance of SAC305Cu solder joints.展开更多
基金funded by the National Natural Science Foundation of China(No.U2330207)the presidential foundation of China Academy of Engineering Physics(No.YZJJZQ2024004).
文摘This study presents the development of high-performance,solvent-free polyurethane-urea(PU)elastomeric coatings engineered for rapid curing and precise sprayability.Utilizing polyoxytetramethylene glycol(PTMG)as the primary polyol and a static-mixing spraying technique,the formulations were systematically optimized.It was found that a soft-segment content of 64% yields optimalmechanical properties,achieving a remarkable tensile strength exceeding 30 MPa.Crucially,the incorporation of an ultra-low concentration(0.002 wt%)of dibutyltin dilaurate catalyst was sufficient to enhance curing completeness and mechanical performance while effectively eliminating moisture-induced foaming,a common challenge in solvent-free spray applications.The gel and tack-free times were successfully reduced to the order of minutes through strategic formulation with the chain extender dimethylsulfidetoluene diamine,minimizing reliance on high catalyst loadings.Theresultant PTMG-based coatings exhibit exceptional comprehensive properties,including a tensile strength>30 MPa,elongation at break>400%,and a tear strength of 66 N/mm,significantly surpassing conventional polypropylene-diamine-based polyurea systems.Furthermore,the coatings demonstrated superior low-temperature flexibility,evidenced by a glass transition temperature of-53℃,and suppressed soft-segment crystallinity.The solvent-free nature and tunable curing kinetics of this system enable precise spraying on complex geometries,effectively overcoming thickness-control limitations for small-object applications.This work establishes a sustainable and high-performance coating solution ideal for demanding impact-and corrosionresistant protective layers.
基金supported by the National Natural Science Foundation of China(Nos.52371128,52304378,52101031 and 92163107).
文摘Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.
基金financially supported by the National Natural Science Foundation of China(No.52102062)the Xi’an Science and Technology Plan Project(No.23LLRH0004)the Key Research and Development Project of Shaanxi Province of China(2024GX-YBXM-352)。
文摘Vat photopolymerization(VPP)3D printing is an optimized technology for complex-shaped ceramic cores,in which the solid loading of ceramic slurries greatly infiuences the microstructure and property of the final ceramic parts.However,the high solid loading of slurries is highly limited by the high viscosity.In this study,silica-based ceramic core slurries with solid loading up to 68vol.%were achieved by the composition design to optimize the performance,considering the curing,rheological,and double bond conversion rate.The slurries demonstrate superior curing and rheological performance with mass ratio of monomers being 3:2 and mass fraction of BYK111 being 4wt.%.Afterwards,the impact of solid loading on the morphology and mechanical properties was investigated.As the solid loading increases,the microstructure becomes gradually dense,leading to an improved flexural strength of 19.5 MPa.Additionally,the sintering shrinkage becomes more uniform,satisfying the casting requirements effectively.This work serves as a guide for the preparation of ceramic slurries with a high solid loading.
基金supported by Stable Support Initiative of the State Key Laboratory of Advanced Nuclear Energy Technology(Grant No.YNSW-0124-0101-03)the author Cheng Zhang would like to thank the support by Stable Support Program for Scientific Research of China(Grant No.WDZC-2023-02-02-05).
文摘Additive manufacturing(AM)is an innovative technique that enables the flexible design and construction of three-dimensional objects.In the nuclear industry,AM enables the use of advanced materials and high-performance components.Although AM processing has been extensively investigated,the corresponding mechanical properties and structural integrity issues of AM parts have received less attention.This study reviews the mechanical behavior and key challenges of typical AM materials,fuel components,compact heat exchangers with complex geometries,and additive repair of damaged reactor components.The findings of this review will guide the efficient and reliable implementation of AM techniques in nuclear reactors.
文摘A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.
基金Funded by National Natural Science Foundation of China(No.52108188)State Key Laboratory of Silicate Materials for Architectures(Wuhan University of Technology)(No.SYSJJ2024-15)+3 种基金State Key Laboratory of Mountain Bridge and Tunnel Engineering,Chongqing Jiaotong University(No.SKLBT-2301)Opening Project of State Key Laboratory of Green Building Materials(No.2022GBM10)Open Research Fund of Key Laboratory of Engineering Materials of Ministry of Water Resources,China Institute of Water Resources and Hydropower Research(No.EMF202407)General Project of Science and Technology Plan of Beijing Municipal Commission of Education(No.KM202110005018)。
文摘This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution concentrations of 3%,6%,9%,and 12%,the optimal dispersion effect was achieved with an ultrasonic dispersion time of 20 minutes.Specifically,at a 6%nano-TiO_(2)content,both the workability and mechanical performance of the cement paste were enhanced.Furthermore,while nano-TiO_(2)did not alter the types of hydration products present in the cement paste,it did increase the amount of C-S-H gels.This enhancement was attributed to a higher number of nucleation sites for hydration products,which promoted hydration and reduced the porosity of the cement paste.
基金supported by the National Key R&D Pro-gram of China(Grant No.2023YFE0114600)The National Natural Science Foundation of China(NSFC)(Grant No.52477029)Joint Laboratory of China-Morocco Green Energy and Advanced Materials,The Youth Innovation Team of Shaanxi Universities and The Xi’an City Science and Technology Project(No.23GXFW0070)。
文摘Floating photovoltaic(FPV)technology is emerging as a highly promising approach to accelerate decarbonization of the global economy,due to its higher power generation efficiency and lower land occupation.With the rapid development of FPV technology,the mechanical performance degradation of key components caused by the harsh marine environment has become a pressing issue,as it significantly contributes to failure behavior observed in FPV systems.A comprehensive compilation of the mechanical performance of key components in FPV systems is also currently unavailable.Here,the mechanical behavior of each structural component in FPV systems under harsh marine environments is systematically reviewed.It further emphasizes the synergistic effects of mechanical performance degradation among different components on the overall system.The drop-off rate(v)of normalized elongation at break(EAB)of polymer under the synergistic effect of various environmental factors increases from 7.5×10^(−4)h^(−1)to 21.8×10^(−4)h^(−1)compared with the single environmental stress.Moreover,the development of novel materials and innovative mechanical structures applied in FPV systems to enhance mechanical performance is discussed.The novel flexible PV modules applied in FPV systems minimize the loads acting on the mooring lines by 80%and increase power generation by 5%.Notably,this paper provides a theoretical foundation for developing standards of FPV systems,especially the establishment of standards related to the synergistic effects of the mechanical performance degradation of different key components on FPV systems.
基金supported by the National Natural Science Foundation of China(Nos.U2468217,U2034205,and 52308391)。
文摘To elucidate the yielding performance of compact yielding anchor cables in working state,a yielding mechanical model incorporating extrusion friction and fastening rotation under confining pressure is constructed.The yielding resistance enhancement effect(ω)caused by working environment constraints is evaluated through multi-layer composite sleeve hole expansion analysis,forming a theoretical framework for calculating the working yielding force.Laboratory and in-situ pull-out tests are conducted to determine the yielding performance and validate the analytical theory.The main conclusions are:(1)Yielding force and energy-release capacity increase withω,significantly outperforming the unconfined state.(2)In-situ tests under varying rockmass and geostress conditions(F1–F3)determine the yielding force increases to 183.4–290.1,204.0–290.8,and 235.0–327.1 kN.(3)The slight deviation(–12.5%to 6.2%)between the theoretical and measured yielding force confirms that the analytical theory effectively describes the working yielding performance.(4)ωincreases with higher geostress and improved rock mechanical properties,with initial geostress(σ_(0))and elastic modulus of surrounding rock(E_(3))identified as critical parameters.
基金supported by the National Natural Science Foundation of China(No.32271976,32371978)scientific and technological innovation funding of Fujian Agriculture and Forestry University(KFb22087,KFB23145).
文摘Due to the features and wide range of potential applications,cellulose ionogels are the subject of extensive research.Green celluloses have been employed as a three-dimensional skeleton network to restrict the ionic liquids(ILs)toward advanced ion-conductive ionogels.Diversiform cellulose ionogels with desirable perfor-mances,via physical/chemical reactions between cellulose and ILs,have been harvested,which have the po-tential to emerge as a bright star in the field of flexible electronics,such as sensors,electrolyte materials as power sources,and thermoelectric devices.Herein,a review regarding cellulose ionogels in terms of fundamental types of cellulose,formation strategies and mechanism,and principal properties is presented.Next,the diverse application prospects of cellulose ionogels in flexible electronics have been summarized.More importantly,the future challenges and advancing directions to be explored for cellulose ionogels are discussed.
基金Project(2023GK2063)supported by the Key R&D Program of Hunan Province,ChinaProject(2023GXGG006)supported by the Key Products in Manufacturing Industry of Hunan Province,ChinaProject(kq2102005)supported by Key Project of Science and Technology of Changsha,China。
文摘Indium(In)has been used as a thermal interface material(TIM1)in high-performance central processing unit(CPU)for better heat dissipation.However,leakage or pump-out of liquid indium during the multiple reflow cycles limits its application in advanced flip chip ball gray array(FCBGA)packaging.Former researchers place a seal or dam structure to prevent In leakage,leading to the risk of In explosion,thermal degradation,or require additional keep-out zones.In this work,a copper foam(CF)matrix was embedded in In to absorb the liquid In and eliminate the leakage of In TIM1 during the multiple reflow cycles,as the CF capillary force.Au/Ni/Cu-Au/Ni/Cu joint was fabricated by soldering with the composite solder at 190℃for 2 min.After reflow cycles,good metallurgical bonding was formed at interfaces of joint.Rod-like Cu_(11)In_(9) formed at the CF and In interface,due to the re-dissolved of Cu_(11)In_(9) crystal.Small amount of Cu atoms from CF can reduce the activity of In,which inhibits the growth of Ni_(3)In_(7) intermetallic compound(IMC)at the interface of In and Au/Ni/Cu substrate.The CF matrix also improved the shear strength(22.9%)and thermal conductivity of the solder joints.Besides,the fracture behavior of solder joints without CF matrix was classified to be ductile type while that with CF matrix was changed to be ductile-brittle mixed type.
文摘Currently,as environmental pollution becomes increasingly severe,flue gas denitrification has emerged as a significant area of research.With the advancement of modern industry and the improvement of living standards,air pollution has gained growing attention.Sulfur dioxide and nitrogen oxides(NO_(x))have become major contributors to air pollution,posing serious harm to the environment.Consequently,flue gas desulfurization and denitrification technologies have become key research focuses in industrial development.This paper explores the selection of agricultural waste carbon sources and their pretreatment methods.It provides an in-depth analysis of the significance of agricultural waste carbon sources in flue gas denitrification,focusing on their performance and mechanisms.The study also discusses the role of agricultural waste carbon sources in flue gas denitrification,aiming to offer new research perspectives for relevant stakeholders.
文摘The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.
基金The National Natural Science Foundation of China(No.51005124)the Opening Foundation of Jiangsu Key Laboratory for Design and Manufacture of Micro-Nano Biomedical Instruments(No.JS-NB-2009-1-1)
文摘This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the space spiral curve, a three-dimensional parametrical geometrical model is constructed. The finite element model is built by using the beam-beam contact elements and 3D beam elements. The constituent nitinol wires are assumed to be linear elastic material. The finite element analysis figures out that the radial stiffness of the stent and the stress distribution of the wires are influenced by all the structural parameters. The helix pitch of the wires is the most important factor. Under the condition of the same load and other structural parameters remaining unchanged, when the number of wires is 24, the stress of the wire crosssection is at the minimum. A comparison between the vitro experimental results and the analytical results is conducted, and the data is consistent, which proves that the current finite element model can be used to appropriately predict the mechanical performance of the braided esophageal stents.
基金supported by the Natural Science Foundation of China(Grant Nos.T2325013,52288102,52090024,12034009,12474004,and 12304036)the National Key R&D Program of China Grant No.2023YFA1610000+1 种基金the Fundamental Research Funds for the Central Universitiesthe Program for Jilin University and Sun Yat-sen University.
文摘We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptional mechanical performance,including an ideal compressive strength of 343 GPa at a pressure of 300 GPa,~33% higher than that of diamond.This ultrahigh strength arises from the synergistic interplay between its three-dimensional covalent framework and hybridized bonding topology,which enables isotropic stress accommodation and dynamic electronic rearrangement.These results establish cage-N as a promising non-carbon ultrahard material and provide a bonding-driven route toward designing superhard frameworks under extreme conditions.
文摘The high hydrophilicity of pineapple leaf fibres(PALF)limits their use in cement-and gypsum-based composites exposed to moisture.This study evaluates,for the first time,the combined effect of palm kernel oil and beeswax on the hygroscopic resistance and mechanical stability of PALF.The fibres were functionalised with three formulations(oil,wax,and a 1:2 oil/wax blend)applied at different mass ratios(CR=0.5-2).Treatments increased the average bundle diameter by up to+46%(238μm)and reduced density down to 1.06 g/cm^(3).Hygroscopically,water absorption decreased from 202.4%(raw fibres)to 76.3%(CR=2),representing a maximum reduction of 59.4%in saline medium,while moisture regain dropped from 27.9%to 14.6%(−47.7%).The oil/wax blend proved most effective,simultaneously reducing water absorption(−51.2%)and moisture regain(−46.8%)at CR=1.Mechanically,the fibres retained tensile strength(415.2 vs.460.8 MPa,+11%at CR=1)and exhibited enhanced ductility(+62.5%,with elongation at break increasing from 1.6%to 2.6%),without significantly altering Young’s modulus(12.3 to 10 GPa).Water absorption kinetics were accurately described by the Czel and Mohsenin models(R^(2)>0.98).These findings clearly demonstrate that bio-based lipid coatings can provide an eco-friendly alternative to conventional chemical treatments.They improve hygroscopic resistance and preserve mechanical integrity of PALF,providing original quantitative data for their integration into durable cement-and gypsum-based composites subjected to humid or cyclic wet-dry conditions.
基金support of the Research and Development Program in Key Areas of Guangdong Province,China(No.2019B090907001)the Science and Technology Program of Guangdong Province,China(No.2014B010129002)the National Key R&D Program of China(No.2017YFB0305800)。
文摘The densification characterization,phase constitution,precipitation evolution and mechanical performance of Al−Mg−Sc−Zr alloy processed by laser powder bed fusion(LPBF)were systematically investigated.Moreover,the evolution of phase constitution and precipitation behavior after heat treatment were characterized by using X-ray diffraction(XRD)and transmission electron microscope(TEM)analysis.The ultimate tensile strength(UTS)of as-built samples ranged from 396.8 to 414.6 MPa as the scanning speed decreased from 1600 to 1000 mm/s.After post heat treatment,the yield strength(YS)increased to(513.1±1.3)MPa,while the UTS increased from(414.6±5.1)to(539.2±1.5)MPa.The significant improvement of mechanical performance was ascribed to the formation of secondary Al3(Sc,Zr)precipitates.
文摘The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. The results show that not only the alloy composition and heat treatment before forming influence the formability, but also they have an effect on the paint bake response of the alloys. Increasing the alloy Si content, decreasing Mg/Si ratio and adding 0.3% Cu （mass fraction） were generally found to improve the tensile ductility and formability of the alloys studied, while pre-ageing was found to decrease these properties. A full property profile of these alloys in terms of strength, tensile ductility, work hardening, strain rate sensitivity, forming limit and paint bake response was presented.
基金Project supported by the Baotou Aluminum Co. Ltd.
文摘The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, EDS and X-ray diffractometer, the microstructure and phase composition of aluminum rod were measured and analyzed. The results indicate that the content of rare earth element Ce is between 0.05% -0.16% in the aluminum rod for electrical purpose. Its tensile strength is enhanced to some extent. The research also discovers that the tensile strength is enhanced remarkably with impurity element Si content increases. Because influence of Si is big to the conductivity, the Si content should be controlled continuously strictly in the aluminum for electrical purpose. Adding rare earth element Ce reduces the solid solubility of Si in the aluminum matrix, and the negative effect of Si on the aluminum conductor reduces effectively. So the limit of in Si content in aluminum rod for electrical purpose can be relaxed moderately.
基金financial supports from the National Key Research and Development Program of China(2017YFA0403804)the National Natural Science Foundation of China(51425402,51671073)。
文摘ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.
文摘This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−xBiCu solder joints were investigated.Bi-doping modified the microstructure of the solder joints by refining the primaryβ-Sn and eutectic phases.Bi-doping below 2 wt.%dissolved in theβ-Sn matrix and formed a solid solution,whereas Bi additions equal to or greater than 2 wt.%formed Bi precipitates in theβ-Sn matrix.Solid solution strengthening and precipitation strengthening mechanisms in theβ-Sn matrix increased the ultimate tensile strength and microhardness of the alloy from 35.7 MPa and 12.6 HV to 55.3 MPa and 20.8 HV,respectively,but elongation decreased from 24.6%to 16.1%.The fracture surface of a solder joint containing 2 wt.%Bi was typical of a brittle failure rather than a ductile failure.The interfacial layer of all solder joints comprised two parallel IMC layers:a layer of Cu6Sn5 and a layer of Cu3Sn.The interfacial layer was thinner and the shear strength was greater in SAC305−xBiCu joints than in SAC305Cu solder joints.Therefore,small addition of Bi refined microstructure,reduced melting temperature and improved the mechanical performance of SAC305Cu solder joints.
