The process of repetitive upsetting-extrusion （RUE） was used to achieve severe plastic deformation （SPD） for an as-cast AZ61 magnesium alloy in temperature range of 285-380 ℃. The microstructure and mechanical pr...The process of repetitive upsetting-extrusion （RUE） was used to achieve severe plastic deformation （SPD） for an as-cast AZ61 magnesium alloy in temperature range of 285-380 ℃. The microstructure and mechanical properties of the as-cast and RUE processed AZ61 alloys were investigated. The results indicated that homogeneous fine-grained structure with mean grain size of 3.5 μm was obtained as the accumulated true strain in the axial direction increased to 4.28 after three RUE passes at 285 ℃. The dominant reason of grain refinement was considered the dynamic recrystallization induced by strain localization. It was also found that the microstructural evolution was affected by temperature and accumulated deformation. The mechanical properties of RUE processed AZ61 alloys were significantly improved owing to grain refinement. Furthermore, the relationship between deformation parameters and mechanical properties of AZ61 alloy prepared by RUE processing was revealed by tensile tests carried out at room temperature.展开更多
TiB/Ti-1.5Fe-2.25Mo composites were synthesized in situ using the spark plasma sintering （SPS） method at temperatures of 850-1150 °C. The effect of the sintering temperature on microstructure and mechanical pro...TiB/Ti-1.5Fe-2.25Mo composites were synthesized in situ using the spark plasma sintering （SPS） method at temperatures of 850-1150 °C. The effect of the sintering temperature on microstructure and mechanical properties of the composites was investigated. The results indicate that the aspect ratio of the in situ synthesized TiB whiskers in Ti alloy matrix decreases rapidly with an increase in sintering temperature. However, both the relative density of the sintered specimens and the volume content of TiB whiskers in composites increase with increasing sintering temperature. Thus, the bending strength of the composites synthesized using SPS process increases slowly with increasing the sintering temperature from 850 to 1150 °C. TiB/Ti-1.5Fe-2.25Mo composite synthesized at 1150 °C using SPS method exhibits the highest bending strength of 1596 MPa due to the formation of fine TiB whiskers in Ti alloy matrix and the dense microstructure of the composite.展开更多
Geological disasters will happen in cold regions because of the effects of freeze-thaw cycles on rocks or soils, so studying the effects of these cycles on the mechanical characteristics and permeability properties of...Geological disasters will happen in cold regions because of the effects of freeze-thaw cycles on rocks or soils, so studying the effects of these cycles on the mechanical characteristics and permeability properties of rocks is very important. In this study, red sandstone samples were frozen and thawed with o, 4, 8 and 12 cycles, each cycle including 12 h of freezing and 12 h of thawing. The P-wave velocities of these samples were measured, and the mechanical properties and evolution of the steady-state permeabilities were investigated in a series of uniaxial and triaxial compression tests. Experimental results show that, with the increasing of cyclic freeze-thaw times, the P-wave velocity of the red sandstone decreases. The number of freeze-thaw cycles has a significant influence on the uniaxial compressive strength, elastic modulus, cohesion, and angle of internal friction. The evolution of permeability of the rock samples after cycles of freeze-thaw in a complete stress-strain process under triaxial compression is closely related to the variation of the microstructure in the rock. There is a highly corresponding relationship between volumetric strain and permeability with axial strain in all stages of the stress-strain behaviour.展开更多
The effects of Ni content on the microstructure and the wetting behavior of Sn-9Zn-xNi solders on Al and Cu substrates, as well as the mechanical properties and electrochemical corrosion behavior of Al/Sn-9Zn-xNi/Cu s...The effects of Ni content on the microstructure and the wetting behavior of Sn-9Zn-xNi solders on Al and Cu substrates, as well as the mechanical properties and electrochemical corrosion behavior of Al/Sn-9Zn-xNi/Cu solder joints, were investigated. The microstructure of Sn-gZn-xNi revealed that tiny Zn and coarsened Ni5Zn21 phases dispersed in theβ-Sn matrix. The wettability of Sn-9Zn-xNi solders on Al substrate was much better than that on Cu substrate. With increasing Ni content, the wettability on Cu substrate was slightly improved but became worse on Al substrate. In the Al/Sn-9Zn-xNi/Cu joints, an Al4.2Cu3.2Zn0.7 intermetallic compound （IMC） layer formed at the Sn-gZn-xNi/Cu interfaces, while an Al-Zn-Sn solid solution layer formed at the Sn-9Zn-xNi/Al interface. The mixed compounds of Ni3Sna and Al3Ni dispersed in the solder matrix and coarsened with increasing Ni content, thus leading to a reduction in shear strength of the Al/Sn-9Zn- xNi/Cu joints. Al particles were segregated at both interfaces in the solder joints. The corrosion potentials of Sn-9Zn-xNi solders continuously increased with increasing Ni content. The Al/Sn-9Zn-0.25Ni/Cu joint was found to have the best electrochemical corrosion resistance in 5% NaCl solution.展开更多
Novel Ti6Al4V particles-reinforced AZ91 Mg matrix composites were successfully fabricated by stir casting method. The stirring time in semisolid condition directly affected the particle distribution and the quality of...Novel Ti6Al4V particles-reinforced AZ91 Mg matrix composites were successfully fabricated by stir casting method. The stirring time in semisolid condition directly affected the particle distribution and the quality of the ingots. Furthermore, the optimal speed of the heating and the liquid stirring could overcome particle settlement caused by the density difference between the matrix and the particles. Ti6Al4V particles distributed uniformly in the composites with different particle contents. The average grain size decreased with the increase in the particle contents. The Ti6A14V particles bonded pretty well with the alloy matrix. In addition, there were some interfacial reactions in the composites. There were rod-like A13Ti phases at the interface. The precipitates extended from the particle surface to the matrix, and they might improve the interfacial bonding strength. The ultimate tensile strength, yield strength and elastic modulus were enhanced as the particle contents increased, and the elongation was much better than that of the same matrix material reinforced with SiC particles. Thus, the novel composites exhibit better comprehensive mechanical properties.展开更多
This work aims to reveal the relationships between the microstructure, mechanical properties and flow behavior of die-casting AlMg5Si2Mn alloy. Results indicated that the microstructure of the die-cast AlMgsSi2Mn cons...This work aims to reveal the relationships between the microstructure, mechanical properties and flow behavior of die-casting AlMg5Si2Mn alloy. Results indicated that the microstructure of the die-cast AlMgsSi2Mn consists of α1-Al grains, fine-size α2-Al grains and （Al ＋ Mg2Si） eutectic. The surface layer observed has the thickness in a range of 120-135 μm, while an ellipse-like surface layer edge is observed in the corner of the plateqike sample. Tensile strength and elongation （3） of the specimens are slightly decreased along the die-filling direction due to the backflow of melt. Pure （Al ＋ Mg2Si） eutectic layer and ultra-fine-size α2-Al grains observed are around the overflow channels. Mass feeding is predominantly responsible for the superior mechanical properties of the round bars as compared to those of plate-like samples.展开更多
The effective connection of 1050 Al and AZ31 Mg was realized by magnetic pulse welding.The maximum tensile-shear force of the dissimilar Al/Mg metal lap joint reached 97%of that of the 1050 Al alloy base material by o...The effective connection of 1050 Al and AZ31 Mg was realized by magnetic pulse welding.The maximum tensile-shear force of the dissimilar Al/Mg metal lap joint reached 97%of that of the 1050 Al alloy base material by optimizing the process parameters.The microstructure of dissimilar Al/Mg welded joints was analysed by Scanning Electron Microscope(SEM),Energy Dispersive Spectrometer(EDS)and Electron Backscattered Diffraction(EBSD).The results show that the key to obtaining high shear strength of Al/Mg dissimilar metal joints is mainly due to the following two reasons.On the one hand,grain refinement and element interdiffusion occur at the interface.On the other hand,no intermetallic compounds are formed at the interface.展开更多
The cooling rate sensitivities of A1TiB, RE and A1TiB-RE refiners were investigated using laboratory experiments and the actual industrial applications of A356 automotive wheel via low pressure die casting technology....The cooling rate sensitivities of A1TiB, RE and A1TiB-RE refiners were investigated using laboratory experiments and the actual industrial applications of A356 automotive wheel via low pressure die casting technology. Their impact mechanisms on the microstructure and mechanical properties of the A356 alloy were discussed. The results demonstrated that the AITiB-RE refiner possessed most effective and synergetic refinement effects compared to the individual A1TiB or RE refiners. The A1TiB-RE refiner exhibited the least sensitivity to the cooling rate changes than the other refiners. The comprehensive properties of alloy wheel refined by the A1TiB-RE refiner were improved significantly. The tensile strength, yield strength, and elongation of wheel spoke improved by approximately 11.3%, 10.8% and 44.1%, respectively. The property difference values of the tensile strength, yield strength, and elongation in different positions of the wheel decreased from 14.8%, 31.2% and 47.7% to 8.6%, 27.1% and 30.9%, respectively.展开更多
Microstructural evolution and mechanical properties of in situ TiB2/A1 composites fabricated with exothermic reaction process under high-intensity ultra- sound produced by the magnetostrictive transducer were investig...Microstructural evolution and mechanical properties of in situ TiB2/A1 composites fabricated with exothermic reaction process under high-intensity ultra- sound produced by the magnetostrictive transducer were investigated. In this method, the microstructure and grain refining performance of the TiB2/A1 composites were characterized by optical morphology （OM）, scanning electron microscopy （SEM）, energy-dispersive spec- trometer （EDS）, and X-ray diffraction （XRD） analysis. Microstructural observations show a decreasing trend in the grain size of the composites due to the ultrasound and the content of TiB2 particles in the composites. Compared with the process without ultrasound, the morphology and ag- glomeration of TiB2 particles are improved by high-in- tensity ultrasound. Meanwhile, it is proposed that the formation of TiBz particles occurs via the transformation from TiA13, and at the optimal amount of the reactants, the conversion efficiency of TiA13 into TiB2 almost reaches up to 100 %. Finally, the effects of high-intensity ultrasound and TiB2 particles on the mechanical properties of the TiB2/A1 composites were also discussed.展开更多
Various types of wound debridement approaches are currently available in clinical practice such as autolytie, enzymatic. biodebridement, mechanical, and surgical debridemenl techniques. A critical look at these variou...Various types of wound debridement approaches are currently available in clinical practice such as autolytie, enzymatic. biodebridement, mechanical, and surgical debridemenl techniques. A critical look at these various options can explain their potential but also their limitations. In this study, a novel textile pad, which is composed of polyester filaments on the fleecy side and a bioeompatible coating on the opposite side, was made to provide a safe, inexpensive, easier and especially more efficient debridement process that can be used in all healthcare settings by all healthcare practitioners. Eighteen kinds of samples were prepared with different pile density, ground yarn count and coating amount. Dimensional morphology, stitch density, mass per unit area and mechanical properties were investigated to study the intrinsic relationship of structure and properties of textile pad for wound debridement. Results showed that tensile strength and suturing strength at piped site increased obviously with the increment of ground yarn count, while the amount of coating could also have a slight impact on these two properties. However, compressive load was mainly affected by pile density, with no obvious relation to ground yarn count and coating amount.展开更多
β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical prop...β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical properties of Si3N4 ceramics prepared using this method were compared with those obtained by hot pressing process. Well densified Si3N4 ceramics with finer and homogeneous microstructure and better mechanical properties were obtained in the case of the SPS technique at 200°C lower than that of hot pressing. The microhardness is 15.72 GPa, the bending strength is 716.46 MPa, and the fracture toughness is 7.03 MPa·m1/2.展开更多
The one-dimensional carbon nanotubes/nanorods(CNT/CNR)mixed nano-carbon material was successfully prepared by halloysite nanotubes(HNTs)as the template for the first time,in which CNT was formed through PVA modificati...The one-dimensional carbon nanotubes/nanorods(CNT/CNR)mixed nano-carbon material was successfully prepared by halloysite nanotubes(HNTs)as the template for the first time,in which CNT was formed through PVA modification in internal surface of HNTs and CNR was obtained by nanocasting PVA in hollow nanostructure of HNTs.The CNT of the mixture with flexible structure has ca.20 nm in pore diameter and ca.500 nm in length,whereas the CNR with hard and solid structure shows ca.30 nm in diameter and ca.2μm in length.For application as fillers,the CNT/CNR mixed nano-material is used to reinforce the properties of polytetrafluoroethylene(PTFE).The mechanical and tribological properties of PTFE nanocomposites were intensively examined by a series of testing.The ring-on-ring counterface was used to evaluate the tribological behavior of the nanocomposites.The results showed that the volume wear rate of the CNT/CNR-reinforced PTFE nanocomposite after being filled with 0.3%of CNT/CNR was only 1/700 of that of the pure PTFE under a load of 200 N and a rotary speed of 200 r/min,while other mechanical and tribological performance was comparable to the performance of pure PTFE,which exhibited a desirable application prospect.展开更多
The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimen...The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimental results displayed that the tensile strength of the joint made with angular butt joint and 0.3 ram-wide gap reached 266 MPa, the joint fractured through the heat-affected zone or base metal during tensile testing, and the microstructure examination showed that no macropore appeared in the fusion zone. However, macropores in diameter of larger than 200 micron occurred for other joint designs, the tensile strength of the resultant joints decreased, and the joints fractured through the fusion zone during tensile testing. The fracture surfaces were examined by scanning electron microscopy and the microhardness distribution in the joints was measured by using a Vickers microhardness tester.展开更多
The effects of magnesium addition on the dispersoid precipitation as well as mechanical properties of 3xxx alloys wereinvestigated. The microstructures in as-cast and heat-treated conditions were evaluated by optical ...The effects of magnesium addition on the dispersoid precipitation as well as mechanical properties of 3xxx alloys wereinvestigated. The microstructures in as-cast and heat-treated conditions were evaluated by optical microscopy and transmissionelectron microscopy. The results reveal that Mg has a strong influence on the distribution and volume fraction of dispersoids duringprecipitation heat treatment. The microhardness and yield strength at ambient temperature increase with increasing Mg content. Thesolid solution and dispersoid strengthening mechanisms of materials after heat treatment are quantitatively analyzed. Dispersoidstrengthening for the alloys is the predominant strengthening mechanism after precipitation heat treatment. An analytical model isintroduced to predict the evolution of ambient-temperature yield strength.展开更多
We studied the effect of salinity on nail-hold- ing power in wood construction. In saline solution, the holding power of nails was less than in purified water. With the increase of salt concentration, the surface and ...We studied the effect of salinity on nail-hold- ing power in wood construction. In saline solution, the holding power of nails was less than in purified water. With the increase of salt concentration, the surface and side nail- holding power of the wood specimens both declined, but the differences between salinity treatments were not sig- nificant. However, compared to the surface and side nail- holding power, the power on the edge was generally less and the difference was not obvious in different salt con- centrations. In the same salt concentration, with the extension of the processing cycle, the performance of holding power of nails showed a downward trend, expect the temporary rise in the middle.展开更多
The effect of water depth on underwater wet welds was investigated by underwater wet shielded metal-arc welding technique. The microstructures, chemical composition, welding defects, and mechanical properties were stu...The effect of water depth on underwater wet welds was investigated by underwater wet shielded metal-arc welding technique. The microstructures, chemical composition, welding defects, and mechanical properties were studied. The contents of alloying elements decrease, while the oxygen content increases with water depth. Within 55 m depth, the carbon monoxide reaction is controlling the oxygen content which will further control the contents of alloying elements. The columnar microstructures in weld metal obtained at shallow water consist of grain boundary ferrite, side-plate ferrite, and acicular ferrite, while those at depth greater than 11 m exhibit more proeutectoid ferrite due to the loss of alloying elements. Mechanical properties are a strong function of depth owing to the increase in oxidation of alloying elements and porosity. Welds obtained within 11 m show preferable strength, ductility, and toughness. The mechanical properties significantly drop from 11 to 25 m because of the increased porosity and oxidation of alloying elements.展开更多
To improve the strength, toughness, heat-resistance and deformability of magnesium alloy, the microstructure and mechanical properties of ZK60 alloy strengthened by Mg-Zn-Nd spherical quasi-crystal phase (I-phase) par...To improve the strength, toughness, heat-resistance and deformability of magnesium alloy, the microstructure and mechanical properties of ZK60 alloy strengthened by Mg-Zn-Nd spherical quasi-crystal phase (I-phase) particles were investigated. Mg40Zn55Nd5 (I-phase) particles in addition to α-Mg, MgZn phase and MgZn2 phases can be obtained in ZK60-based composites under normal casting condition by the addition of quasi-crystal containing Mg-Zn-Nd master alloy. The experimental results show that the introduction of Mg-Zn-Nd spherical quasi-crystal phase into ZK60 alloy makes a great contribution to the refinement of the matrix microstructures and the improvement of mechanical properties. While adding Mg-Zn-Nd spherical quasi-crystal master alloy of 4.0wt.%, the ultimate tensile strength and yield strength of ZK60-based composite at ambient temperature reach their peak values of 256.7 MPa and 150.4 MPa, which were about 17.8% and 24.1% higher respectively than those of the ZK60 alloy. The improved mechanical properties are mainly attributed to the pinning effect of the quasi-crystal particles (I-phase) at the grain boundaries. This research results provide a new way for strengthening and toughening of magnesium alloys as well as a new application of Mg-based spherical quasi-crystals.展开更多
Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N...Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N_44 grains, and the p-Si_3N_4 grain growth as well as theoxynitride glass chemical characteristic on the microstructure and mechanical properties wereinvestigated. The experimental results show that the p-Si_3N_4 grains in high oxynitride glass growto elongated rod-like crystals and form the stereo-network structure. Under the sintering conditionsof 1800 deg C and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and anaverage of 1 mu m can be obtained. A large amount of oxynitride glass phase with high nitrogencontent enhances the elevated temperature fracture toughness because of its high softeningtemperature and high viscosity. In the present material, the crack deflection and pullout of theelongated rod-like P-Si_3N_44 grains are the primary toughening mechanisms.展开更多
Fe-WC nanocomposites were successfully fabricated by high-frequency induction heated sintering of ball milled nanostructure powders. The ball milled powders were characterized by X-ray diffraction. Density measurement...Fe-WC nanocomposites were successfully fabricated by high-frequency induction heated sintering of ball milled nanostructure powders. The ball milled powders were characterized by X-ray diffraction. Density measurements by the Archimedes method show that all sintered samples have the relative density higher than 95%. Studies on the effects of WC content, milling speed, and milling time indicate that a higher milling speed and a more WC content lead to the improvement of mechanical properties. There is a very good distribution of WC particles in the Fe matrix at the milling speed of 650 r/rain. For the sintered sample 20-5-650 （20wt% WC, milling time of 5 h, and milled speed of 650 r/min）, the maximum Brinell hardness and yield stress are obtained to be 3.25 GPa and 858 MPa, respectively. All sintered samples have brittle fracture during compression test except the sample 20-5-650.展开更多
Ab initio calculations are performed to investigate the ground state properties, structural phase transition, electronic structure and mechanical properties of lithium nitride （Li3N）, lithium imide （Li2NH） and lit...Ab initio calculations are performed to investigate the ground state properties, structural phase transition, electronic structure and mechanical properties of lithium nitride （Li3N）, lithium imide （Li2NH） and lithium amide （LiNH2）. The computed ground state properties like equilibrium lattice constant, cell volume, valence electron density, cohesive energy, bulk modulus and its derivatives are in good agreement with available experimental data. The structural phase transitions from α-P6/mmm to β-P63/mmc phase at a pressure of 17.5 GPa in LiaN and cubic （Fm3m） to hexagonal （P63/ mmc） phase at a pressure of 102 GPa in lithium imide （Li2NH） are observed. A new high pressure hexagonal （P63/mmc） phase is predicted for LiENH. Electronic structure reveals that Li3N and LiNH2 are semiconductors, whereas Li2NH is an insulator. The calculated elastic constants indicate that these materials are mechanically stable at ambient condition.展开更多
基金Project(51075098)supported by the National Natural Science Foundation of ChinaProject(HIT.NSRIF.2014006)supported by the Fundamental Research Funds for the Central Universities,China
文摘The process of repetitive upsetting-extrusion （RUE） was used to achieve severe plastic deformation （SPD） for an as-cast AZ61 magnesium alloy in temperature range of 285-380 ℃. The microstructure and mechanical properties of the as-cast and RUE processed AZ61 alloys were investigated. The results indicated that homogeneous fine-grained structure with mean grain size of 3.5 μm was obtained as the accumulated true strain in the axial direction increased to 4.28 after three RUE passes at 285 ℃. The dominant reason of grain refinement was considered the dynamic recrystallization induced by strain localization. It was also found that the microstructural evolution was affected by temperature and accumulated deformation. The mechanical properties of RUE processed AZ61 alloys were significantly improved owing to grain refinement. Furthermore, the relationship between deformation parameters and mechanical properties of AZ61 alloy prepared by RUE processing was revealed by tensile tests carried out at room temperature.
基金Prject(20111D0503200316)supported by the Programme for Peking Excellent Talents in University,ChinaProject(613135)supported by 973 Defence Plan of China
文摘TiB/Ti-1.5Fe-2.25Mo composites were synthesized in situ using the spark plasma sintering （SPS） method at temperatures of 850-1150 °C. The effect of the sintering temperature on microstructure and mechanical properties of the composites was investigated. The results indicate that the aspect ratio of the in situ synthesized TiB whiskers in Ti alloy matrix decreases rapidly with an increase in sintering temperature. However, both the relative density of the sintered specimens and the volume content of TiB whiskers in composites increase with increasing sintering temperature. Thus, the bending strength of the composites synthesized using SPS process increases slowly with increasing the sintering temperature from 850 to 1150 °C. TiB/Ti-1.5Fe-2.25Mo composite synthesized at 1150 °C using SPS method exhibits the highest bending strength of 1596 MPa due to the formation of fine TiB whiskers in Ti alloy matrix and the dense microstructure of the composite.
基金supported by the National Basic Research Program of China (973 Program) (Grant No. 2011CB013503)the National Natural Science Foundation of China (Grant No. 51374112)the Promotion Program for Young and Middle-aged Teacher in Science and Technology Research of Huaqiao University (ZQN-PY112)
文摘Geological disasters will happen in cold regions because of the effects of freeze-thaw cycles on rocks or soils, so studying the effects of these cycles on the mechanical characteristics and permeability properties of rocks is very important. In this study, red sandstone samples were frozen and thawed with o, 4, 8 and 12 cycles, each cycle including 12 h of freezing and 12 h of thawing. The P-wave velocities of these samples were measured, and the mechanical properties and evolution of the steady-state permeabilities were investigated in a series of uniaxial and triaxial compression tests. Experimental results show that, with the increasing of cyclic freeze-thaw times, the P-wave velocity of the red sandstone decreases. The number of freeze-thaw cycles has a significant influence on the uniaxial compressive strength, elastic modulus, cohesion, and angle of internal friction. The evolution of permeability of the rock samples after cycles of freeze-thaw in a complete stress-strain process under triaxial compression is closely related to the variation of the microstructure in the rock. There is a highly corresponding relationship between volumetric strain and permeability with axial strain in all stages of the stress-strain behaviour.
基金supported by the National Natural Science Foundation of China (Nos. U0734006 and 51171036)
文摘The effects of Ni content on the microstructure and the wetting behavior of Sn-9Zn-xNi solders on Al and Cu substrates, as well as the mechanical properties and electrochemical corrosion behavior of Al/Sn-9Zn-xNi/Cu solder joints, were investigated. The microstructure of Sn-gZn-xNi revealed that tiny Zn and coarsened Ni5Zn21 phases dispersed in theβ-Sn matrix. The wettability of Sn-9Zn-xNi solders on Al substrate was much better than that on Cu substrate. With increasing Ni content, the wettability on Cu substrate was slightly improved but became worse on Al substrate. In the Al/Sn-9Zn-xNi/Cu joints, an Al4.2Cu3.2Zn0.7 intermetallic compound （IMC） layer formed at the Sn-gZn-xNi/Cu interfaces, while an Al-Zn-Sn solid solution layer formed at the Sn-9Zn-xNi/Al interface. The mixed compounds of Ni3Sna and Al3Ni dispersed in the solder matrix and coarsened with increasing Ni content, thus leading to a reduction in shear strength of the Al/Sn-9Zn- xNi/Cu joints. Al particles were segregated at both interfaces in the solder joints. The corrosion potentials of Sn-9Zn-xNi solders continuously increased with increasing Ni content. The Al/Sn-9Zn-0.25Ni/Cu joint was found to have the best electrochemical corrosion resistance in 5% NaCl solution.
基金supported by the National Natural Science Foundation of China (Grant No. 51471059)the China Postdoctoral Science Foundation (Grant No. 2014T70328)
文摘Novel Ti6Al4V particles-reinforced AZ91 Mg matrix composites were successfully fabricated by stir casting method. The stirring time in semisolid condition directly affected the particle distribution and the quality of the ingots. Furthermore, the optimal speed of the heating and the liquid stirring could overcome particle settlement caused by the density difference between the matrix and the particles. Ti6Al4V particles distributed uniformly in the composites with different particle contents. The average grain size decreased with the increase in the particle contents. The Ti6A14V particles bonded pretty well with the alloy matrix. In addition, there were some interfacial reactions in the composites. There were rod-like A13Ti phases at the interface. The precipitates extended from the particle surface to the matrix, and they might improve the interfacial bonding strength. The ultimate tensile strength, yield strength and elastic modulus were enhanced as the particle contents increased, and the elongation was much better than that of the same matrix material reinforced with SiC particles. Thus, the novel composites exhibit better comprehensive mechanical properties.
基金financially supported by Guangdong Provincial Department of Science and Technology,China (No.2012A090300016)
文摘This work aims to reveal the relationships between the microstructure, mechanical properties and flow behavior of die-casting AlMg5Si2Mn alloy. Results indicated that the microstructure of the die-cast AlMgsSi2Mn consists of α1-Al grains, fine-size α2-Al grains and （Al ＋ Mg2Si） eutectic. The surface layer observed has the thickness in a range of 120-135 μm, while an ellipse-like surface layer edge is observed in the corner of the plateqike sample. Tensile strength and elongation （3） of the specimens are slightly decreased along the die-filling direction due to the backflow of melt. Pure （Al ＋ Mg2Si） eutectic layer and ultra-fine-size α2-Al grains observed are around the overflow channels. Mass feeding is predominantly responsible for the superior mechanical properties of the round bars as compared to those of plate-like samples.
基金supported by National Natural Science Foundation of China(No.51474101,51975202)the equipment pre-research project of China(Nos.41422060204)the Natural Science Foundation of Hunan Province(2019JJ30005).
文摘The effective connection of 1050 Al and AZ31 Mg was realized by magnetic pulse welding.The maximum tensile-shear force of the dissimilar Al/Mg metal lap joint reached 97%of that of the 1050 Al alloy base material by optimizing the process parameters.The microstructure of dissimilar Al/Mg welded joints was analysed by Scanning Electron Microscope(SEM),Energy Dispersive Spectrometer(EDS)and Electron Backscattered Diffraction(EBSD).The results show that the key to obtaining high shear strength of Al/Mg dissimilar metal joints is mainly due to the following two reasons.On the one hand,grain refinement and element interdiffusion occur at the interface.On the other hand,no intermetallic compounds are formed at the interface.
基金financially supported by the National High Technology Research and Development Program(No.2013AA031002)
文摘The cooling rate sensitivities of A1TiB, RE and A1TiB-RE refiners were investigated using laboratory experiments and the actual industrial applications of A356 automotive wheel via low pressure die casting technology. Their impact mechanisms on the microstructure and mechanical properties of the A356 alloy were discussed. The results demonstrated that the AITiB-RE refiner possessed most effective and synergetic refinement effects compared to the individual A1TiB or RE refiners. The A1TiB-RE refiner exhibited the least sensitivity to the cooling rate changes than the other refiners. The comprehensive properties of alloy wheel refined by the A1TiB-RE refiner were improved significantly. The tensile strength, yield strength, and elongation of wheel spoke improved by approximately 11.3%, 10.8% and 44.1%, respectively. The property difference values of the tensile strength, yield strength, and elongation in different positions of the wheel decreased from 14.8%, 31.2% and 47.7% to 8.6%, 27.1% and 30.9%, respectively.
基金financially supported by the National High Technology Research and Development Program of China(No.2013AA031104)
文摘Microstructural evolution and mechanical properties of in situ TiB2/A1 composites fabricated with exothermic reaction process under high-intensity ultra- sound produced by the magnetostrictive transducer were investigated. In this method, the microstructure and grain refining performance of the TiB2/A1 composites were characterized by optical morphology （OM）, scanning electron microscopy （SEM）, energy-dispersive spec- trometer （EDS）, and X-ray diffraction （XRD） analysis. Microstructural observations show a decreasing trend in the grain size of the composites due to the ultrasound and the content of TiB2 particles in the composites. Compared with the process without ultrasound, the morphology and ag- glomeration of TiB2 particles are improved by high-in- tensity ultrasound. Meanwhile, it is proposed that the formation of TiBz particles occurs via the transformation from TiA13, and at the optimal amount of the reactants, the conversion efficiency of TiA13 into TiB2 almost reaches up to 100 %. Finally, the effects of high-intensity ultrasound and TiB2 particles on the mechanical properties of the TiB2/A1 composites were also discussed.
基金Chinese Universities Scientific Fund，National Feature Specialty Construction "Functional Materials",China
文摘Various types of wound debridement approaches are currently available in clinical practice such as autolytie, enzymatic. biodebridement, mechanical, and surgical debridemenl techniques. A critical look at these various options can explain their potential but also their limitations. In this study, a novel textile pad, which is composed of polyester filaments on the fleecy side and a bioeompatible coating on the opposite side, was made to provide a safe, inexpensive, easier and especially more efficient debridement process that can be used in all healthcare settings by all healthcare practitioners. Eighteen kinds of samples were prepared with different pile density, ground yarn count and coating amount. Dimensional morphology, stitch density, mass per unit area and mechanical properties were investigated to study the intrinsic relationship of structure and properties of textile pad for wound debridement. Results showed that tensile strength and suturing strength at piped site increased obviously with the increment of ground yarn count, while the amount of coating could also have a slight impact on these two properties. However, compressive load was mainly affected by pile density, with no obvious relation to ground yarn count and coating amount.
基金the National Natural Science Foundation of China (No.2001AA333080).
文摘β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical properties of Si3N4 ceramics prepared using this method were compared with those obtained by hot pressing process. Well densified Si3N4 ceramics with finer and homogeneous microstructure and better mechanical properties were obtained in the case of the SPS technique at 200°C lower than that of hot pressing. The microhardness is 15.72 GPa, the bending strength is 716.46 MPa, and the fracture toughness is 7.03 MPa·m1/2.
基金funded by the Talent Introduction Fund of Yangzhou University(2012)the Zhenjiang High Technology Research Institute of Yangzhou University(2017)+5 种基金the Key Research Project-Industry Foresight and General Key Technology of Yangzhou(YZ2015020)the Innovative Talent Program of Green Yang Golden Phoenix(yzlyjfjh2015CX073)the Yangzhou Social Development Project(YZ2016072)the Jiangsu Province Six Talent Peaks Project(2014-XCL-013)the Jiangsu Industrial-Academic-Research Prospective Joint Project(BY2016069-02)the Priority Academic Program Development of Jiangsu Higher Education Institutions and Top-notch Academic Programs Project of Jiangsu Higher Education Institutions(PPZY2015B112)for the financial support
文摘The one-dimensional carbon nanotubes/nanorods(CNT/CNR)mixed nano-carbon material was successfully prepared by halloysite nanotubes(HNTs)as the template for the first time,in which CNT was formed through PVA modification in internal surface of HNTs and CNR was obtained by nanocasting PVA in hollow nanostructure of HNTs.The CNT of the mixture with flexible structure has ca.20 nm in pore diameter and ca.500 nm in length,whereas the CNR with hard and solid structure shows ca.30 nm in diameter and ca.2μm in length.For application as fillers,the CNT/CNR mixed nano-material is used to reinforce the properties of polytetrafluoroethylene(PTFE).The mechanical and tribological properties of PTFE nanocomposites were intensively examined by a series of testing.The ring-on-ring counterface was used to evaluate the tribological behavior of the nanocomposites.The results showed that the volume wear rate of the CNT/CNR-reinforced PTFE nanocomposite after being filled with 0.3%of CNT/CNR was only 1/700 of that of the pure PTFE under a load of 200 N and a rotary speed of 200 r/min,while other mechanical and tribological performance was comparable to the performance of pure PTFE,which exhibited a desirable application prospect.
基金supported by the State Key Lab of Advanced Welding and Joining,Harbin Institute of Technology (Project No.09009)
文摘The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimental results displayed that the tensile strength of the joint made with angular butt joint and 0.3 ram-wide gap reached 266 MPa, the joint fractured through the heat-affected zone or base metal during tensile testing, and the microstructure examination showed that no macropore appeared in the fusion zone. However, macropores in diameter of larger than 200 micron occurred for other joint designs, the tensile strength of the resultant joints decreased, and the joints fractured through the fusion zone during tensile testing. The fracture surfaces were examined by scanning electron microscopy and the microhardness distribution in the joints was measured by using a Vickers microhardness tester.
基金the financial support of the Natural Sciences and Engineering Research Council of Canada (NSERC)Rio Tinto Aluminum through the NSERC Industry Research Chair in the Metallurgy of Aluminum Transformation at University of Quebec at Chicoutimi
文摘The effects of magnesium addition on the dispersoid precipitation as well as mechanical properties of 3xxx alloys wereinvestigated. The microstructures in as-cast and heat-treated conditions were evaluated by optical microscopy and transmissionelectron microscopy. The results reveal that Mg has a strong influence on the distribution and volume fraction of dispersoids duringprecipitation heat treatment. The microhardness and yield strength at ambient temperature increase with increasing Mg content. Thesolid solution and dispersoid strengthening mechanisms of materials after heat treatment are quantitatively analyzed. Dispersoidstrengthening for the alloys is the predominant strengthening mechanism after precipitation heat treatment. An analytical model isintroduced to predict the evolution of ambient-temperature yield strength.
基金financially supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)Jiangsu Overseas Research&Training Program for University Prominent Young&Middle-aged Teachers and Presidents
文摘We studied the effect of salinity on nail-hold- ing power in wood construction. In saline solution, the holding power of nails was less than in purified water. With the increase of salt concentration, the surface and side nail- holding power of the wood specimens both declined, but the differences between salinity treatments were not sig- nificant. However, compared to the surface and side nail- holding power, the power on the edge was generally less and the difference was not obvious in different salt con- centrations. In the same salt concentration, with the extension of the processing cycle, the performance of holding power of nails showed a downward trend, expect the temporary rise in the middle.
基金the financial support of marine scientific research project (investigate on the key technology of underwater welding and inspection processes-developing special machines and processes for local dry and wet underwater welding) sponsored by Offshore Oil Engineering Co., Ltd.
文摘The effect of water depth on underwater wet welds was investigated by underwater wet shielded metal-arc welding technique. The microstructures, chemical composition, welding defects, and mechanical properties were studied. The contents of alloying elements decrease, while the oxygen content increases with water depth. Within 55 m depth, the carbon monoxide reaction is controlling the oxygen content which will further control the contents of alloying elements. The columnar microstructures in weld metal obtained at shallow water consist of grain boundary ferrite, side-plate ferrite, and acicular ferrite, while those at depth greater than 11 m exhibit more proeutectoid ferrite due to the loss of alloying elements. Mechanical properties are a strong function of depth owing to the increase in oxidation of alloying elements and porosity. Welds obtained within 11 m show preferable strength, ductility, and toughness. The mechanical properties significantly drop from 11 to 25 m because of the increased porosity and oxidation of alloying elements.
基金supported by the National Science Foundation of China(No.50571073)the Natural Science Foundation of Shanxi province(No.2009011028-3)
文摘To improve the strength, toughness, heat-resistance and deformability of magnesium alloy, the microstructure and mechanical properties of ZK60 alloy strengthened by Mg-Zn-Nd spherical quasi-crystal phase (I-phase) particles were investigated. Mg40Zn55Nd5 (I-phase) particles in addition to α-Mg, MgZn phase and MgZn2 phases can be obtained in ZK60-based composites under normal casting condition by the addition of quasi-crystal containing Mg-Zn-Nd master alloy. The experimental results show that the introduction of Mg-Zn-Nd spherical quasi-crystal phase into ZK60 alloy makes a great contribution to the refinement of the matrix microstructures and the improvement of mechanical properties. While adding Mg-Zn-Nd spherical quasi-crystal master alloy of 4.0wt.%, the ultimate tensile strength and yield strength of ZK60-based composite at ambient temperature reach their peak values of 256.7 MPa and 150.4 MPa, which were about 17.8% and 24.1% higher respectively than those of the ZK60 alloy. The improved mechanical properties are mainly attributed to the pinning effect of the quasi-crystal particles (I-phase) at the grain boundaries. This research results provide a new way for strengthening and toughening of magnesium alloys as well as a new application of Mg-based spherical quasi-crystals.
文摘Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N_44 grains, and the p-Si_3N_4 grain growth as well as theoxynitride glass chemical characteristic on the microstructure and mechanical properties wereinvestigated. The experimental results show that the p-Si_3N_4 grains in high oxynitride glass growto elongated rod-like crystals and form the stereo-network structure. Under the sintering conditionsof 1800 deg C and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and anaverage of 1 mu m can be obtained. A large amount of oxynitride glass phase with high nitrogencontent enhances the elevated temperature fracture toughness because of its high softeningtemperature and high viscosity. In the present material, the crack deflection and pullout of theelongated rod-like P-Si_3N_44 grains are the primary toughening mechanisms.
文摘Fe-WC nanocomposites were successfully fabricated by high-frequency induction heated sintering of ball milled nanostructure powders. The ball milled powders were characterized by X-ray diffraction. Density measurements by the Archimedes method show that all sintered samples have the relative density higher than 95%. Studies on the effects of WC content, milling speed, and milling time indicate that a higher milling speed and a more WC content lead to the improvement of mechanical properties. There is a very good distribution of WC particles in the Fe matrix at the milling speed of 650 r/rain. For the sintered sample 20-5-650 （20wt% WC, milling time of 5 h, and milled speed of 650 r/min）, the maximum Brinell hardness and yield stress are obtained to be 3.25 GPa and 858 MPa, respectively. All sintered samples have brittle fracture during compression test except the sample 20-5-650.
基金The financial assistance from UGC under research award scheme(No.F:30-36/2011 SA-II)
文摘Ab initio calculations are performed to investigate the ground state properties, structural phase transition, electronic structure and mechanical properties of lithium nitride （Li3N）, lithium imide （Li2NH） and lithium amide （LiNH2）. The computed ground state properties like equilibrium lattice constant, cell volume, valence electron density, cohesive energy, bulk modulus and its derivatives are in good agreement with available experimental data. The structural phase transitions from α-P6/mmm to β-P63/mmc phase at a pressure of 17.5 GPa in LiaN and cubic （Fm3m） to hexagonal （P63/ mmc） phase at a pressure of 102 GPa in lithium imide （Li2NH） are observed. A new high pressure hexagonal （P63/mmc） phase is predicted for LiENH. Electronic structure reveals that Li3N and LiNH2 are semiconductors, whereas Li2NH is an insulator. The calculated elastic constants indicate that these materials are mechanically stable at ambient condition.
