In this study, two fluorinated polyurethanes（FPU） containing carborane groups in the main chains were firstly designed and synthesized via the reaction of hexamethylene diisocyanate trimer（HDI trimer） with fluorin...In this study, two fluorinated polyurethanes（FPU） containing carborane groups in the main chains were firstly designed and synthesized via the reaction of hexamethylene diisocyanate trimer（HDI trimer） with fluorinated polyesters（CFPETs） having hydroxyl-terminated carborane groups at room temperature. The structures of carborane fluorinated polyesters（CFPETs） and polyurethanes（CFPUs） were characterized by gel permeation chromatography（GPC）, Fourier transform infrared（FTIR） spectroscopy and nuclear magnetic resonance（NMR） measurements. The thermal stability, mechanical properties, Shore A hardness, solvent resistance and acid-alkali resistance of the carborane fluorinated polyurethane films were also studied. Thermogravimetric analysis（TGA） tests manifested that the introduction of carborane groups into the main chain of fluorinated polyurethane endowed the obtained fluorinated polyurethane with excellent thermal stability. The thermal decomposition temperature of carborane fluorinated polyurethane（CFPU） increased by 190 °C compared with that of the carborane-free fluorinated polyurethane（FPU）. Even at 800 °C, CFPU showed the char yield of 66.5%, which was higher than that of FPU（34.3%）. The carborane-containing fluorinated polyurethanes also showed excellent chemical resistance and prominent mechanical property even after the cured films being immersed into Jet aircraft oil or 37% HCl for 168 h or at high temperature（700 °C）. It is found that the structural characteristics of carborane group and the compacted structure of CFPU effectively improve the thermal stability, mechanical property, solvent resistance and acid-alkali resistance of the carborane-free fluorinated polyurethane. These excellent properties make CFPU as the useful raw materials to prepare the high temperature resistant coatings or adhesives for automotive engines, engine or fuel tank of aircraft and other equipment working in high-temperature or high concentrations of acid-alkali environments.展开更多
The aim of present work is to investigate the influencing factors on mechanical property stability of Cu-Mo-Ni alloyed austempered ductile iron （ADI）. The results show that after austenitized at 900℃ for 2 h follow...The aim of present work is to investigate the influencing factors on mechanical property stability of Cu-Mo-Ni alloyed austempered ductile iron （ADI）. The results show that after austenitized at 900℃ for 2 h followed by austempered at 370℃for another 2 h, the mechanical property of the alloyed ADI can reach the Germanite GGG-100 standard, i.e. σb≮1000 MPa,δ≮5%, at 95% confidence level. And the satisfactory mechanical properties were obtained when the alloyed ADI was austenitized at 850℃ to 1 000 ℃ for 1-4 h, and austempered at 355℃ to 400℃ for another 1 h to 4 h. The microstructures, including nodule number, white bright zone content （martensite-containing interdendritic segregation zone） and retained austenite content, can significantly influence the mechanical properties of the ADI. In order to obtain the good combinations of strength and ductility, the volume fraction of white bright zone should he less than 5%, and the retained austenite contents maintain hetween 30 % and 40%. The application of inoculation techniques to increase graphite nodule number can effectively reduce the white bright zone content in the structure.展开更多
The influence of Ti and Nb on the microstructure,mechanical properties,and second-phase precipitation of 430 ferritic stainless steel was investigated.In addition to optical microscopy,transmission electron microscopy...The influence of Ti and Nb on the microstructure,mechanical properties,and second-phase precipitation of 430 ferritic stainless steel was investigated.In addition to optical microscopy,transmission electron microscopy and X-ray diffraction analyses,tensile tests,and carbonitride extraction experiments were conducted to investigate the microscopic mechanisms.The results showed that the primary precipitates in SUS 430 ferritic stainless steel were Cr_（23）C_6,Mn_（23）C_6,and Cr_7C_3,and the primary strengthening mechanism was precipitation strengthening.When Ti was added separately,the main precipitates were TiC and TiN.However,coarse TiC adversely affected the mechanical properties of steel.When double-stabilized with Ti and Nb,coarse TiC was replaced by fine NbC.The type of precipitation was altered,and precipitation and solid solution strengthening occurred.Therefore,the tensile strength and plastic strain ratio（r-value） improved to 433.60 MPa and 1.37,respectively.展开更多
Oxide-dispersion-strengthened （ODS） ferritic steels are promising candidates for structural applications in the future nuclear reactors. The higher chromium contents of ODS ferritic steels, the better the corrosion ...Oxide-dispersion-strengthened （ODS） ferritic steels are promising candidates for structural applications in the future nuclear reactors. The higher chromium contents of ODS ferritic steels, the better the corrosion resistance, which can meet the harsh corrosion environment of the advanced reactors. However, increasing the Cr content may also lead to the brittleness of the ODS steels when serving at high temperatures. The ODS ferritic steels with different Cr contents （12, 16 and 18 wt% Cr, respectively） were fabricated by mechanical alloying, hot isostatic pressing and forging. Mechanical properties and microstructure evolution of the ODS ferritic steels after aging at 753 K for 2000 h were investigated. It is found that both Vickers hardness and yield strength of 18%Cr ODS ferritic steel were strongly increased and the impact energy was decreased after aging at 753 K. In order to explore the reasons for changes in the mechanical properties, the fracture surfaces were characterized by scanning electron microscopy, and microstructures after aging were observed by transmission electron microscopy. The impact fracture of 18%Cr ODS ferritic steel belongs to quasi-cleavage facture, which is consistent with its very low impact energy. The grain size and dispersed oxide particles of different ODS steels are very stable. M23C6 carbide and M2C carbide were found in 12%Cr ODS steel and 16%Cr ODS steels, respectively.展开更多
Carbon fiber reinforced high density polyethylene multi-layered laminated composite panels（HDPE/CF MLCP） with excellent in-plane properties along transverse direction have been formulated. Composite architectures wi...Carbon fiber reinforced high density polyethylene multi-layered laminated composite panels（HDPE/CF MLCP） with excellent in-plane properties along transverse direction have been formulated. Composite architectures with carbon fiber（CF） designed in 2D layout in conventional composites can alleviate their properties in thickness direction, but all attempts so far developed have achieved restrained success. Here,we have exposed an approach to the high strength composite challenge, without altering the 2D stack design on the basis of concept of fiber reinforced laminated composites that would provide enhanced mechanical and thermal properties along transverse direction. CF sheets allowed the buckling of adjoining plies in 2D MLCP. We fabricated 2D MLCP by stacking the alternative CF and HDPE layers under different loading conditions, which resulted in high strength composites. These plies of CF and HDPE served as unit cells for MLCP, with CF offering much-needed fracture toughness and hardness to these materials.For 2D HDPE/CF MLCP, we demonstrated noteworthy improvement in physical and chemical interaction between CF and HDPE, in-plane fracture strain, flexural strength（30.684 MPa）, bending modulus（7436.254 MPa）, thermal stability（40.94%）, and surface morphology, upon increasing the CF layers up to twenty, enabling these composites truly for high temperature and high strength applications.展开更多
Hydrogels are a class of special materials that contain a large amount of water and behave like rubber.These materials have found broad applications in tissue engineering,cell culturing,regenerative medicine etc.Recen...Hydrogels are a class of special materials that contain a large amount of water and behave like rubber.These materials have found broad applications in tissue engineering,cell culturing,regenerative medicine etc.Recently,the exploration of peptide-based supramolecular hydrogels has greatly expanded the repertoire of hydrogels suitable for biomedical applications.However,the mechanical properties of peptide-based hydrogels are intrinsically weak.Therefore,it is crucial to develop methods that can improve the mechanical stability of such peptide-based hydrogels.In this review,we explore the factors that determine or influence the mechanical stability of peptide-based hydrogels and summarize several key elements that may guide scientists to achieve mechanically improved hydrogels.In addition,we exemplified several methods that have been successfully developed to prepare hydrogels with enhanced mechanical stability.These mechanically strong peptide-based hydrogels may find broad applications as novel biomaterials.It is still challenging to engineer hydrogels in order to mimic the mechanical properties of biological tissues.More hydrogel materials with optimal mechanical properties suitable for various types of biological applications will be available in the near future.展开更多
To develop an efficient and bio-compatible way to improve the thermal and mechanical properties of addition type liquid silicone rubber（LSR）, a series of modified LSR samples were prepared by introducing octavinyl-p...To develop an efficient and bio-compatible way to improve the thermal and mechanical properties of addition type liquid silicone rubber（LSR）, a series of modified LSR samples were prepared by introducing octavinyl-polyhedral oligosilsesquioxanes（VPOSS） and high purity silicon sol singly or in combination before vulcanization. Significant correlation was found between the loading rate of VPOSS and thermal properties. However, mechanical properties were negatively correlated with VPOSS content within the range experimented, which may be ascribed to material defect caused by uneven distribution and aggregation. Furthermore, test results approved that the introducing of silicon sol indeed affected the stabilities of the polymer by restraining the material defect caused by the aggregation of POSS molecules and improving cross link density. For example, adding 10%-20% of silicon sol into VPOSS（1.0%） modified LSR will increase tear resistance by 43.9%-85.7%, elongation at break by 31.7%-57.3%, residue at 800 ℃ in N2 atmosphere by 32.0%-37.9%, residue at 650 ℃ in air atmosphere by 70.9%-91.6%, respectively. This work proves that, to incorporate VPOSS into LSR by hydrosilylation, and to use silicon sol as dispersant and reinforce filler can become an efficient way to improve the mechanical property, thermal stability and bio-compatibility of LSR in the future.展开更多
The present work establishes a systematic approach based on the application of in-situ Fourier transform infrared spectroscopy （FTIR） for the investigation of the crystal structure, thermal stability, redox behavior...The present work establishes a systematic approach based on the application of in-situ Fourier transform infrared spectroscopy （FTIR） for the investigation of the crystal structure, thermal stability, redox behavior （temperature-programmed reduction/temperatureprogrammed re-oxidation） as well as the catalytic properties of Co3O4 thin films. The syntheses of Co3O4 were achieved by chemical vapor deposition in the temperature range of 400-500℃. The structure analysis of the as-prepared material revealed the presence of two prominent IR bands peaking at 544 cm-1 （υ1） and 650 cm-1 （υ2） respectively, which originate from the stretching vibrations of the Co-O bond, characteristic of the Co3O4 spinel. The lattice stability limit of Co3O4 was estimated to be above 650℃. The redox properties of the spinel structure were determined by integrating the area under the emission bands υ1 and υ2 as a function of the temperature. Moreover, Co3O4 has been successfully tested as a catalyst towards complete oxidation of dimethyl ether below 340 ℃. The exhaust gas analysis during the catalytic process by in situ absorption FTIR revealed that only CO2 and H2O were detected as the final products in the catalytic reaction. The redox behavior suggests that the oxidation of dimethyl ether over Co3O4 follows a Mars-van Krevelen type mechanism. The comprehensive application of in situ FTIR provides a novel diagnostic tool in characterization and performance test of catalysts.展开更多
基金financially supported by International Cooperative Project (Harbin Institute of Technology 2014DFR40370)International Cooperative Project (Wuxi HIT Limited Corporation & Research Institute of New Materials BZ2015024)
文摘In this study, two fluorinated polyurethanes（FPU） containing carborane groups in the main chains were firstly designed and synthesized via the reaction of hexamethylene diisocyanate trimer（HDI trimer） with fluorinated polyesters（CFPETs） having hydroxyl-terminated carborane groups at room temperature. The structures of carborane fluorinated polyesters（CFPETs） and polyurethanes（CFPUs） were characterized by gel permeation chromatography（GPC）, Fourier transform infrared（FTIR） spectroscopy and nuclear magnetic resonance（NMR） measurements. The thermal stability, mechanical properties, Shore A hardness, solvent resistance and acid-alkali resistance of the carborane fluorinated polyurethane films were also studied. Thermogravimetric analysis（TGA） tests manifested that the introduction of carborane groups into the main chain of fluorinated polyurethane endowed the obtained fluorinated polyurethane with excellent thermal stability. The thermal decomposition temperature of carborane fluorinated polyurethane（CFPU） increased by 190 °C compared with that of the carborane-free fluorinated polyurethane（FPU）. Even at 800 °C, CFPU showed the char yield of 66.5%, which was higher than that of FPU（34.3%）. The carborane-containing fluorinated polyurethanes also showed excellent chemical resistance and prominent mechanical property even after the cured films being immersed into Jet aircraft oil or 37% HCl for 168 h or at high temperature（700 °C）. It is found that the structural characteristics of carborane group and the compacted structure of CFPU effectively improve the thermal stability, mechanical property, solvent resistance and acid-alkali resistance of the carborane-free fluorinated polyurethane. These excellent properties make CFPU as the useful raw materials to prepare the high temperature resistant coatings or adhesives for automotive engines, engine or fuel tank of aircraft and other equipment working in high-temperature or high concentrations of acid-alkali environments.
文摘The aim of present work is to investigate the influencing factors on mechanical property stability of Cu-Mo-Ni alloyed austempered ductile iron （ADI）. The results show that after austenitized at 900℃ for 2 h followed by austempered at 370℃for another 2 h, the mechanical property of the alloyed ADI can reach the Germanite GGG-100 standard, i.e. σb≮1000 MPa,δ≮5%, at 95% confidence level. And the satisfactory mechanical properties were obtained when the alloyed ADI was austenitized at 850℃ to 1 000 ℃ for 1-4 h, and austempered at 355℃ to 400℃ for another 1 h to 4 h. The microstructures, including nodule number, white bright zone content （martensite-containing interdendritic segregation zone） and retained austenite content, can significantly influence the mechanical properties of the ADI. In order to obtain the good combinations of strength and ductility, the volume fraction of white bright zone should he less than 5%, and the retained austenite contents maintain hetween 30 % and 40%. The application of inoculation techniques to increase graphite nodule number can effectively reduce the white bright zone content in the structure.
文摘The influence of Ti and Nb on the microstructure,mechanical properties,and second-phase precipitation of 430 ferritic stainless steel was investigated.In addition to optical microscopy,transmission electron microscopy and X-ray diffraction analyses,tensile tests,and carbonitride extraction experiments were conducted to investigate the microscopic mechanisms.The results showed that the primary precipitates in SUS 430 ferritic stainless steel were Cr_（23）C_6,Mn_（23）C_6,and Cr_7C_3,and the primary strengthening mechanism was precipitation strengthening.When Ti was added separately,the main precipitates were TiC and TiN.However,coarse TiC adversely affected the mechanical properties of steel.When double-stabilized with Ti and Nb,coarse TiC was replaced by fine NbC.The type of precipitation was altered,and precipitation and solid solution strengthening occurred.Therefore,the tensile strength and plastic strain ratio（r-value） improved to 433.60 MPa and 1.37,respectively.
文摘Oxide-dispersion-strengthened （ODS） ferritic steels are promising candidates for structural applications in the future nuclear reactors. The higher chromium contents of ODS ferritic steels, the better the corrosion resistance, which can meet the harsh corrosion environment of the advanced reactors. However, increasing the Cr content may also lead to the brittleness of the ODS steels when serving at high temperatures. The ODS ferritic steels with different Cr contents （12, 16 and 18 wt% Cr, respectively） were fabricated by mechanical alloying, hot isostatic pressing and forging. Mechanical properties and microstructure evolution of the ODS ferritic steels after aging at 753 K for 2000 h were investigated. It is found that both Vickers hardness and yield strength of 18%Cr ODS ferritic steel were strongly increased and the impact energy was decreased after aging at 753 K. In order to explore the reasons for changes in the mechanical properties, the fracture surfaces were characterized by scanning electron microscopy, and microstructures after aging were observed by transmission electron microscopy. The impact fracture of 18%Cr ODS ferritic steel belongs to quasi-cleavage facture, which is consistent with its very low impact energy. The grain size and dispersed oxide particles of different ODS steels are very stable. M23C6 carbide and M2C carbide were found in 12%Cr ODS steel and 16%Cr ODS steels, respectively.
文摘Carbon fiber reinforced high density polyethylene multi-layered laminated composite panels（HDPE/CF MLCP） with excellent in-plane properties along transverse direction have been formulated. Composite architectures with carbon fiber（CF） designed in 2D layout in conventional composites can alleviate their properties in thickness direction, but all attempts so far developed have achieved restrained success. Here,we have exposed an approach to the high strength composite challenge, without altering the 2D stack design on the basis of concept of fiber reinforced laminated composites that would provide enhanced mechanical and thermal properties along transverse direction. CF sheets allowed the buckling of adjoining plies in 2D MLCP. We fabricated 2D MLCP by stacking the alternative CF and HDPE layers under different loading conditions, which resulted in high strength composites. These plies of CF and HDPE served as unit cells for MLCP, with CF offering much-needed fracture toughness and hardness to these materials.For 2D HDPE/CF MLCP, we demonstrated noteworthy improvement in physical and chemical interaction between CF and HDPE, in-plane fracture strain, flexural strength（30.684 MPa）, bending modulus（7436.254 MPa）, thermal stability（40.94%）, and surface morphology, upon increasing the CF layers up to twenty, enabling these composites truly for high temperature and high strength applications.
基金supported by the National Natural Science Foundation of China(Grant Nos.11304156,11334004,91127026,31170813 and 11074115)China Postdoctoral Science Foundation(Grant No.2013M531312)+1 种基金the Priority Academic Program Development of Jiangsu Higher Education Institutionsthe Program for New Century Excellent Talents in University
文摘Hydrogels are a class of special materials that contain a large amount of water and behave like rubber.These materials have found broad applications in tissue engineering,cell culturing,regenerative medicine etc.Recently,the exploration of peptide-based supramolecular hydrogels has greatly expanded the repertoire of hydrogels suitable for biomedical applications.However,the mechanical properties of peptide-based hydrogels are intrinsically weak.Therefore,it is crucial to develop methods that can improve the mechanical stability of such peptide-based hydrogels.In this review,we explore the factors that determine or influence the mechanical stability of peptide-based hydrogels and summarize several key elements that may guide scientists to achieve mechanically improved hydrogels.In addition,we exemplified several methods that have been successfully developed to prepare hydrogels with enhanced mechanical stability.These mechanically strong peptide-based hydrogels may find broad applications as novel biomaterials.It is still challenging to engineer hydrogels in order to mimic the mechanical properties of biological tissues.More hydrogel materials with optimal mechanical properties suitable for various types of biological applications will be available in the near future.
基金Funded by the National Natural Science Foundation of China(No.31170558)
文摘To develop an efficient and bio-compatible way to improve the thermal and mechanical properties of addition type liquid silicone rubber（LSR）, a series of modified LSR samples were prepared by introducing octavinyl-polyhedral oligosilsesquioxanes（VPOSS） and high purity silicon sol singly or in combination before vulcanization. Significant correlation was found between the loading rate of VPOSS and thermal properties. However, mechanical properties were negatively correlated with VPOSS content within the range experimented, which may be ascribed to material defect caused by uneven distribution and aggregation. Furthermore, test results approved that the introducing of silicon sol indeed affected the stabilities of the polymer by restraining the material defect caused by the aggregation of POSS molecules and improving cross link density. For example, adding 10%-20% of silicon sol into VPOSS（1.0%） modified LSR will increase tear resistance by 43.9%-85.7%, elongation at break by 31.7%-57.3%, residue at 800 ℃ in N2 atmosphere by 32.0%-37.9%, residue at 650 ℃ in air atmosphere by 70.9%-91.6%, respectively. This work proves that, to incorporate VPOSS into LSR by hydrosilylation, and to use silicon sol as dispersant and reinforce filler can become an efficient way to improve the mechanical property, thermal stability and bio-compatibility of LSR in the future.
文摘The present work establishes a systematic approach based on the application of in-situ Fourier transform infrared spectroscopy （FTIR） for the investigation of the crystal structure, thermal stability, redox behavior （temperature-programmed reduction/temperatureprogrammed re-oxidation） as well as the catalytic properties of Co3O4 thin films. The syntheses of Co3O4 were achieved by chemical vapor deposition in the temperature range of 400-500℃. The structure analysis of the as-prepared material revealed the presence of two prominent IR bands peaking at 544 cm-1 （υ1） and 650 cm-1 （υ2） respectively, which originate from the stretching vibrations of the Co-O bond, characteristic of the Co3O4 spinel. The lattice stability limit of Co3O4 was estimated to be above 650℃. The redox properties of the spinel structure were determined by integrating the area under the emission bands υ1 and υ2 as a function of the temperature. Moreover, Co3O4 has been successfully tested as a catalyst towards complete oxidation of dimethyl ether below 340 ℃. The exhaust gas analysis during the catalytic process by in situ absorption FTIR revealed that only CO2 and H2O were detected as the final products in the catalytic reaction. The redox behavior suggests that the oxidation of dimethyl ether over Co3O4 follows a Mars-van Krevelen type mechanism. The comprehensive application of in situ FTIR provides a novel diagnostic tool in characterization and performance test of catalysts.
