Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bott...Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.展开更多
A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests...A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.展开更多
This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution conc...This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution concentrations of 3%,6%,9%,and 12%,the optimal dispersion effect was achieved with an ultrasonic dispersion time of 20 minutes.Specifically,at a 6%nano-TiO_(2)content,both the workability and mechanical performance of the cement paste were enhanced.Furthermore,while nano-TiO_(2)did not alter the types of hydration products present in the cement paste,it did increase the amount of C-S-H gels.This enhancement was attributed to a higher number of nucleation sites for hydration products,which promoted hydration and reduced the porosity of the cement paste.展开更多
The microstructure and mechanical performance of the unidirectionally and cross-directionally rolled Mg-8Li-6Zn-1Y(in wt.%)sheets have been investigated and compared.It reveals that after the unidirectional rolling(UR...The microstructure and mechanical performance of the unidirectionally and cross-directionally rolled Mg-8Li-6Zn-1Y(in wt.%)sheets have been investigated and compared.It reveals that after the unidirectional rolling(UR),the broken I-phase particles are aggregated at theα-Mg/β-Li phase interfaces.However,the cross-rolling(CR)process can not only severely break the bulk I-phase,but also cause the obviously uniform distribution of I-phase particles in the matrix phases.Moreover,the average grain size of the CR samples is 3.61μm and about 50%that of the UR samples.The maximum texture intensities ofα-Mg andβ-Li phases in the CR samples are slightly stronger than those in the UR samples.Tensile results demonstrate that the CR process can effectively enhance the tensile properties and remarkably reduce the mechanical anisotropy of the alloy.For the UR samples,the yield strength,ultimate tensile strength,and elongation ratio along the rolling direction(RD)are 164 MPa,198 MPa,and 16.4%,whereas those along the transverse direction(TD)are 157 MPa,185 MPa,and 22.0%,respectively.For the CR samples,their mechanical properties are basically the same and the mechanical anisotropy is almost eliminated.The yield strength,ultimate tensile strength,and elongation ratio along the cross-rolling direction 1(CRD1)and 2(CRD2)are respectively measured to be 181 MPa and 182 MPa,220 MPa and 218 MPa,20.6%and 20.7%.Failure analysis indicates that for the UR samples being tensile tested along the RD and TD,microcracks are preferentially initiated in the region of aggregated I-phase particles.For the CR samples being tensile tested along both two cross-rolling directions,the initiation of micro-cracks mainly occurs at the I-phase/matrix phase interfaces and in the interior of matrix phases.展开更多
Alloying seriously deteriorates the thermal conductivity of magnesium(Mg)alloys,thus,restricts their applications in the fields of computer,communication,and consumer products.In order to improve the thermal conductiv...Alloying seriously deteriorates the thermal conductivity of magnesium(Mg)alloys,thus,restricts their applications in the fields of computer,communication,and consumer products.In order to improve the thermal conductivity of Mg alloys,adding carbon nanotube(CNT)combined with aging treatment is proposed in this work,i.e.fabricating the D-CNT(a kind of dispersed CNT)reinforced ZK61 matrix composite via powder metallurgy,and conducting aging treatment to the composite.Results indicate the as-aged ZK61/0.6 wt.%D-CNT composite achieved an excellent thermal conductivity of 166 W/(mK),exhibiting 52.3%enhancement in comparison with matrix,as well as tensile yield strength of 321 MPa,ultimate tensile strength of 354 of MPa,and elongation of 14%.The simultaneously enhanced thermal conductivity and mechanical performance are mainly attributed to:(1)the embedded interface of the D-CNT with matrix and(2)the coherent interface of precipitates with matrix.It is expected the current work can provide a clue for devising Mg matrix composites with integrated structural and functional performances,and enlarge the current restricted applications of Mg alloys.展开更多
This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the spa...This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the space spiral curve, a three-dimensional parametrical geometrical model is constructed. The finite element model is built by using the beam-beam contact elements and 3D beam elements. The constituent nitinol wires are assumed to be linear elastic material. The finite element analysis figures out that the radial stiffness of the stent and the stress distribution of the wires are influenced by all the structural parameters. The helix pitch of the wires is the most important factor. Under the condition of the same load and other structural parameters remaining unchanged, when the number of wires is 24, the stress of the wire crosssection is at the minimum. A comparison between the vitro experimental results and the analytical results is conducted, and the data is consistent, which proves that the current finite element model can be used to appropriately predict the mechanical performance of the braided esophageal stents.展开更多
The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. ...The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. The results show that not only the alloy composition and heat treatment before forming influence the formability, but also they have an effect on the paint bake response of the alloys. Increasing the alloy Si content, decreasing Mg/Si ratio and adding 0.3% Cu （mass fraction） were generally found to improve the tensile ductility and formability of the alloys studied, while pre-ageing was found to decrease these properties. A full property profile of these alloys in terms of strength, tensile ductility, work hardening, strain rate sensitivity, forming limit and paint bake response was presented.展开更多
The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, ...The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, EDS and X-ray diffractometer, the microstructure and phase composition of aluminum rod were measured and analyzed. The results indicate that the content of rare earth element Ce is between 0.05% -0.16% in the aluminum rod for electrical purpose. Its tensile strength is enhanced to some extent. The research also discovers that the tensile strength is enhanced remarkably with impurity element Si content increases. Because influence of Si is big to the conductivity, the Si content should be controlled continuously strictly in the aluminum for electrical purpose. Adding rare earth element Ce reduces the solid solubility of Si in the aluminum matrix, and the negative effect of Si on the aluminum conductor reduces effectively. So the limit of in Si content in aluminum rod for electrical purpose can be relaxed moderately.展开更多
ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performa...ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.展开更多
This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−...This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−xBiCu solder joints were investigated.Bi-doping modified the microstructure of the solder joints by refining the primaryβ-Sn and eutectic phases.Bi-doping below 2 wt.%dissolved in theβ-Sn matrix and formed a solid solution,whereas Bi additions equal to or greater than 2 wt.%formed Bi precipitates in theβ-Sn matrix.Solid solution strengthening and precipitation strengthening mechanisms in theβ-Sn matrix increased the ultimate tensile strength and microhardness of the alloy from 35.7 MPa and 12.6 HV to 55.3 MPa and 20.8 HV,respectively,but elongation decreased from 24.6%to 16.1%.The fracture surface of a solder joint containing 2 wt.%Bi was typical of a brittle failure rather than a ductile failure.The interfacial layer of all solder joints comprised two parallel IMC layers:a layer of Cu6Sn5 and a layer of Cu3Sn.The interfacial layer was thinner and the shear strength was greater in SAC305−xBiCu joints than in SAC305Cu solder joints.Therefore,small addition of Bi refined microstructure,reduced melting temperature and improved the mechanical performance of SAC305Cu solder joints.展开更多
Rare earth -containing PSBR sheet was prepared by reaction of rare earth alkoxide with quaternary ammonium salt of pyridine modified SBR (PSBR) latex, and then it was blended with natural rubber (NR) to produce rare e...Rare earth -containing PSBR sheet was prepared by reaction of rare earth alkoxide with quaternary ammonium salt of pyridine modified SBR (PSBR) latex, and then it was blended with natural rubber (NR) to produce rare earth - containing composite elastomer. It is found that mechanical performance can be improved remarkably. Analyzed by infrared spectrometry (IR), differential scanning calorimetry (DSC) and cross-linking densitometry, the relationship between structure and performance was discussed.展开更多
Solid-state diffusion bonding(DB)of TiAl alloy and Ti2 AlNb alloy was carried out using pure Ti as an interlayer at 1000℃under 20 MPa for 60-120 min.The effects of bonding times on the interfacial microstructure and ...Solid-state diffusion bonding(DB)of TiAl alloy and Ti2 AlNb alloy was carried out using pure Ti as an interlayer at 1000℃under 20 MPa for 60-120 min.The effects of bonding times on the interfacial microstructure and mechanical performance of the TiAl/Ti/Ti_(2)AlNb bonded joints at room temperature(RT)were investigated detailly.The results demonstrated that the diffusion layers(DLs)mainly consisted of four characteristic layers,(Ⅰ)single coarseα_(2)phase adjacent TiAl alloy,(Ⅱ)single refinedα_(2)phase at the bonding interface,(Ⅲ)equiaxed/acicularα_(2)phase embedded inβphase adjacent Ti_(2)AtNb alloy and(IV)both equiaxedα_(2)phase and acicular O phase embedded inβphase adj acent Ti_(2)AlNb alloy,respectively.The thickness of the four layers increased with the increasing of the bonding time.The growth of DLs is controlled by diffusion and the reaction rate constant k for regionⅠ,Ⅱ,ⅢandⅣare 1.22×10^(-6),1.27×10^(-6),2.6×10^(-7)and 7.7×10^(-7)m·s^(-1/2),respectively.Meanwhile,the interfaceα_(2)grain grows up without texture.The maximum tensile strength of 281 MPa was maintained at1000℃for 90 min under the pressure of 20 MPa.Consequently,the phase transformation and dynamic recrystallization behavior of the DLs were discussed.展开更多
Motivated by the huge practical engineering demand for the fundamental understanding of mechanical characteristics of high-speed railway infrastructure,a fullscale multi-functional test platform for high-speed railway...Motivated by the huge practical engineering demand for the fundamental understanding of mechanical characteristics of high-speed railway infrastructure,a fullscale multi-functional test platform for high-speed railway track–subgrade system is developed in this paper,and its main functions for investigating the mechanical performance of track–subgrade systems are elaborated with three typical experimental examples.Comprising the full-scale subgrade structure and all the five types of track structures adopted in Chinese high-speed railways,namely the CRTS I,the CRTS II and the CRTS III ballastless tracks,the double-block ballastless track and the ballasted track,the test platform is established strictly according to the construction standard of Chinese high-speed railways.Three kinds of effective loading methods are employed,including the real bogie loading,multi-point loading and the impact loading.Various types of sensors are adopted in different components of the five types of track–subgrade systems to measure the displacement,acceleration,pressure,structural strain and deformation,etc.Utilizing this test platform,both dynamic characteristics and long-term performance evolution of high-speed railway track–subgrade systems can be investigated,being able to satisfy the actual demand for large-scale operation of Chinese high-speed railways.As examples,three typical experimental studies are presented to elucidate the comprehensive functionalities of the full-scale multi-functional test platform for exploring the dynamic performance and its long-term evolution of ballastless track systems and for studying the long-term accumulative settlement of the ballasted track–subgrade system in high-speed railways.Some interesting phenomena and meaningful results are captured by the developed test platform,which provide a useful guidance for the scientific operation and maintenance of high-speed railway infrastructure.展开更多
Nature consists of various soft tissues with well-ordered hierarchical anisotropic structures, which play essential roles in biological systems to exhibit particular functions. Mimicking bio-tissues, synthetic hydroge...Nature consists of various soft tissues with well-ordered hierarchical anisotropic structures, which play essential roles in biological systems to exhibit particular functions. Mimicking bio-tissues, synthetic hydrogels with anisotropic structures have received considerable attention in recent years. However, existing approaches to fabricate anisotropic hydrogels often require complicated procedures, which are timeconsuming and labor-demanding. Inspired by the dry-induced crystallization phenomenon, we report a simple yet effective prestretching-drying-swelling method to afford anisotropic crystalline polyvinyl alcohol hydrogels. Owing to the distinct anisotropic microstructure, the hydrogels demonstrate excellent mechanical properties with noticeable directional distinction. It is revealed that both the enhancing of pre-orientation strain and the extending of heating time make the hydrogels with better mechanical properties and more remarkable anisotropicity. Owing to the anisotropically aligned structure, the hydrogels exhibit remarkably differential ionic conductivity: the difference between the parallel and vertical conductivity of the same sample can reach as high as 6.6 times, making the materials possible candidates as nano-conductive materials. We anticipate that this simple yet effective approach may become highly useful for fabricating oriented hydrogels and endow the materials with more promising application prospects in the future.展开更多
The aim of this study is to provide the quantificational change laws of strength,stiffness,and deformation capacity of frost-damaged concrete relating to a united index,the data were obtained by different researchers....The aim of this study is to provide the quantificational change laws of strength,stiffness,and deformation capacity of frost-damaged concrete relating to a united index,the data were obtained by different researchers.Then the index of relative compressive strength（RCS） was introduced as the indicator of frost damage and a large number of mechanical performance testing data of frost-damaged concrete were collected and analyzed.By curve fitting,the correlations between RCS and the initial elastic modulus,the strain at peak compressive stress,and biaxial compressive strength,and tensile strength,and the strain at peak tensile stress were established.Thereafter,the analytical stress-strain response of frost-damaged concrete under monotonic loading was presented using RCS and compared with that of the experimental data.Moreover,an isotropic elastoplastic damage model of frost-damaged concrete subjected to repeated loading was established.Finally,we can systematically estimate the effects of frost-damage on the mechanical performance of concrete,which can be provided for the numerical simulation of frost-damaged concrete structures.展开更多
Silk protein builds one of the strongest natural fibers based on its complex nanocomposite structures.However,the mechanical performance of silk protein,related to its molecular structure and packing is still elusive....Silk protein builds one of the strongest natural fibers based on its complex nanocomposite structures.However,the mechanical performance of silk protein,related to its molecular structure and packing is still elusive.In this study,we constructed an atomistic silk protein network model,which reproduces the extensive connection topology of silk protein with structure details of theβ-sheet crystallites and amorphous domains.With the silk protein network model,we investigated the structure evolution and stress distribution of silk protein under external loading.We found a pre-stretching treatment during the spinning process can improve the strength of silk protein.This treatment improves the properties of silk protein network,i.e.,increases the number of nodes and bridges,makes the nodes distributed homogeneously,and induces the bridges in the network well aligned to the loading direction,which is of great benefit to the mechanical performances of silk protein.Our study not only provides a realized atomistic model for silk protein network that well represents the structures and deformations of silk proteins under loading,but also gains deep insights into the mechanism how the pre-loading on silk proteins during spinning improves the mechanical properties of silk fibers.展开更多
Nitrogen doped diamond-like carbon （DLC：N） films were prepared by electron cyclotron resonance chemical vapor deposition （ECR-CVD） on polycrystalline Si chips. Film thickness is about 50 nm. Auger electron spectr...Nitrogen doped diamond-like carbon （DLC：N） films were prepared by electron cyclotron resonance chemical vapor deposition （ECR-CVD） on polycrystalline Si chips. Film thickness is about 50 nm. Auger electron spectroscopy （AES） was used to evaluate nitrogen content, and increasing N2 flow improved N content from 0 to 7.6%. Raman and X-ray photoelectron spectroscopy （XPS） analysis results reveal CN-sp^3C and N-sp^2C structure. With increasing the N2 flow, sp^3C decreases from 73.74% down to 42.66%, and so does N-sp^3C from 68.04% down to 20.23%. The hardness decreases from 29.18 GPa down to 19.74 GPa, and the Young＇s modulus from 193.03 GPa down to 144.52 GPa.展开更多
On the basis of test, nonlinear finite element analysis of reinforcedconcrete (R. C) short-limb shear walls under monotonic horizontal load are carried out by ANSYSprogram in order to understand the evolution of crack...On the basis of test, nonlinear finite element analysis of reinforcedconcrete (R. C) short-limb shear walls under monotonic horizontal load are carried out by ANSYSprogram in order to understand the evolution of cracking, deformation and failure course of thespecimens. At the same time, the results of numerical calculation are compared with the results oftest. The results indicate that, under monotonic horizontal load the failures of the specimens withflange wall and without flange wall all occur at the intersections of lintel bottom and limb ofwall, the failures also occur at the bottom of limb; the load-displacement curve of wall withoutflange is steeper than that of wall with flange, and the ductility is worse than that of wall withflange; the results, such as cracking, deformation, yield load and so on of finite element analysisagree well with the results of test. These results provide theoretical basis of study andapplication of R. C short-limb shear wall.展开更多
The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on t...The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on the mechanical performance of SiCf/phenolic composites after high-temperature pyrolysis was studied through flexural performance test.The results show that the composite material has good thermal stability and high-temperature mechanical properties.After static ablation at 1400℃ for 15 minutes,the flexural strength of the composite material reaches 286 MPa,which is still 7.3%higher than at room temperature,indicating that the composite material still has good mechanical properties even after heat treatment at 1400℃.展开更多
In the induction heating of airport pavement to remove snow and ice,soft magnetic geopolymer composite(SMGC)can be used to gather the dissipated electromagnetic energy,thus enhancing the energy utilization efficiency....In the induction heating of airport pavement to remove snow and ice,soft magnetic geopolymer composite(SMGC)can be used to gather the dissipated electromagnetic energy,thus enhancing the energy utilization efficiency.The aim of this work is to analyze the influence mechanism of iron powder content on the electromagnetic and mechanical performance of SMGC,so as to provide theoretical guidance for the design of soft magnetic layer within airport pavement structure.The results show that the increase of iron powder content reduces the resistance and magnetoresistance of SMGC by decreasing the content of non-magnetic phases between iron powder.However,the reduction of iron powder spacing also provides a shorter transmission path for the inter-particle eddy currents in the SMGC specimen,which enhances the exchange coupling between iron powder,thus increasing the electromagnetic loss.Therefore,the compatibility between magnetic permeability and electromagnetic loss should be considered comprehensively in the mix design of SMGC.In addition,although iron powder can enhance the mechanical properties of SMGC by improving the density of geopolymer matrix,the excessive amount of iron powder can lead to a weak interfacial transition zone between geopolymer matrix and iron powder.According to the induction heating results,optimized SMGC can improve the energy transfer efficiency of induction heating by 24.03%.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52371128,52304378,52101031 and 92163107).
文摘Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.
文摘A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.
基金Funded by National Natural Science Foundation of China(No.52108188)State Key Laboratory of Silicate Materials for Architectures(Wuhan University of Technology)(No.SYSJJ2024-15)+3 种基金State Key Laboratory of Mountain Bridge and Tunnel Engineering,Chongqing Jiaotong University(No.SKLBT-2301)Opening Project of State Key Laboratory of Green Building Materials(No.2022GBM10)Open Research Fund of Key Laboratory of Engineering Materials of Ministry of Water Resources,China Institute of Water Resources and Hydropower Research(No.EMF202407)General Project of Science and Technology Plan of Beijing Municipal Commission of Education(No.KM202110005018)。
文摘This article investigated the factors and mechanisms that affected the workability and mechanical properties of cement paste incorporating nano-TiO_(2).The findings indicated that,for nano-TiO_(2)aqueous solution concentrations of 3%,6%,9%,and 12%,the optimal dispersion effect was achieved with an ultrasonic dispersion time of 20 minutes.Specifically,at a 6%nano-TiO_(2)content,both the workability and mechanical performance of the cement paste were enhanced.Furthermore,while nano-TiO_(2)did not alter the types of hydration products present in the cement paste,it did increase the amount of C-S-H gels.This enhancement was attributed to a higher number of nucleation sites for hydration products,which promoted hydration and reduced the porosity of the cement paste.
基金supported by the National Natural Science Foundation of China Projects under Grant(Nos.52071220,U21A2049,51871211,51701129,and 51971054)China Postdoctoral Science Foundation(No.2023M733572)+7 种基金Liaoning Province’s project of“Revitalizing Liaoning Talents”(No.XLYC1907062)the Doctor Startup Fund of Natural Science Foundation Program of Liaoning Province(No.2019-BS-200)High level achievement construction project of Shenyang Ligong University(No.SYLUXM202105)Liaoning BaiQianWan Talents Program,the Domain Foundation of Equipment Advance Research of 13th Five-year Plan(No.61409220118)National Key Research and Development Program of China under Grant(Nos.2017YFB0702001 and 2016YFB0301105)the Innovation Fund of Institute of Metal Research(IMR),Chinese Academy of Sciences(CAS),the National Basic Research Program of China(973 Program)project under Grant No.2013CB632205the Fundamental Research Fund for the Central Universities under Grant(No.N2009006)Bintech-IMR R&D Program(No.GYY-JSBU-2022–009).
文摘The microstructure and mechanical performance of the unidirectionally and cross-directionally rolled Mg-8Li-6Zn-1Y(in wt.%)sheets have been investigated and compared.It reveals that after the unidirectional rolling(UR),the broken I-phase particles are aggregated at theα-Mg/β-Li phase interfaces.However,the cross-rolling(CR)process can not only severely break the bulk I-phase,but also cause the obviously uniform distribution of I-phase particles in the matrix phases.Moreover,the average grain size of the CR samples is 3.61μm and about 50%that of the UR samples.The maximum texture intensities ofα-Mg andβ-Li phases in the CR samples are slightly stronger than those in the UR samples.Tensile results demonstrate that the CR process can effectively enhance the tensile properties and remarkably reduce the mechanical anisotropy of the alloy.For the UR samples,the yield strength,ultimate tensile strength,and elongation ratio along the rolling direction(RD)are 164 MPa,198 MPa,and 16.4%,whereas those along the transverse direction(TD)are 157 MPa,185 MPa,and 22.0%,respectively.For the CR samples,their mechanical properties are basically the same and the mechanical anisotropy is almost eliminated.The yield strength,ultimate tensile strength,and elongation ratio along the cross-rolling direction 1(CRD1)and 2(CRD2)are respectively measured to be 181 MPa and 182 MPa,220 MPa and 218 MPa,20.6%and 20.7%.Failure analysis indicates that for the UR samples being tensile tested along the RD and TD,microcracks are preferentially initiated in the region of aggregated I-phase particles.For the CR samples being tensile tested along both two cross-rolling directions,the initiation of micro-cracks mainly occurs at the I-phase/matrix phase interfaces and in the interior of matrix phases.
基金supported by National Key Research and Development Program of China(No.2021YFB3701100)Beijing Natural Science Foundation(2192006)National Natural Science Foundation of China(51801004).
文摘Alloying seriously deteriorates the thermal conductivity of magnesium(Mg)alloys,thus,restricts their applications in the fields of computer,communication,and consumer products.In order to improve the thermal conductivity of Mg alloys,adding carbon nanotube(CNT)combined with aging treatment is proposed in this work,i.e.fabricating the D-CNT(a kind of dispersed CNT)reinforced ZK61 matrix composite via powder metallurgy,and conducting aging treatment to the composite.Results indicate the as-aged ZK61/0.6 wt.%D-CNT composite achieved an excellent thermal conductivity of 166 W/(mK),exhibiting 52.3%enhancement in comparison with matrix,as well as tensile yield strength of 321 MPa,ultimate tensile strength of 354 of MPa,and elongation of 14%.The simultaneously enhanced thermal conductivity and mechanical performance are mainly attributed to:(1)the embedded interface of the D-CNT with matrix and(2)the coherent interface of precipitates with matrix.It is expected the current work can provide a clue for devising Mg matrix composites with integrated structural and functional performances,and enlarge the current restricted applications of Mg alloys.
基金The National Natural Science Foundation of China(No.51005124)the Opening Foundation of Jiangsu Key Laboratory for Design and Manufacture of Micro-Nano Biomedical Instruments(No.JS-NB-2009-1-1)
文摘This paper aims to find the relationship between the structural parameters and the radial stiffness of the braided stent and to understand the stress distribution law of the wires. According to the equation of the space spiral curve, a three-dimensional parametrical geometrical model is constructed. The finite element model is built by using the beam-beam contact elements and 3D beam elements. The constituent nitinol wires are assumed to be linear elastic material. The finite element analysis figures out that the radial stiffness of the stent and the stress distribution of the wires are influenced by all the structural parameters. The helix pitch of the wires is the most important factor. Under the condition of the same load and other structural parameters remaining unchanged, when the number of wires is 24, the stress of the wire crosssection is at the minimum. A comparison between the vitro experimental results and the analytical results is conducted, and the data is consistent, which proves that the current finite element model can be used to appropriately predict the mechanical performance of the braided esophageal stents.
文摘The effect of alloy composition and heat treatment, including natural ageing and pre-ageing, on the mechanical performance of eight 6xxx alloys designed with systematically varying Si, Mg and Cu contents was studied. The results show that not only the alloy composition and heat treatment before forming influence the formability, but also they have an effect on the paint bake response of the alloys. Increasing the alloy Si content, decreasing Mg/Si ratio and adding 0.3% Cu （mass fraction） were generally found to improve the tensile ductility and formability of the alloys studied, while pre-ageing was found to decrease these properties. A full property profile of these alloys in terms of strength, tensile ductility, work hardening, strain rate sensitivity, forming limit and paint bake response was presented.
基金Project supported by the Baotou Aluminum Co. Ltd.
文摘The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, EDS and X-ray diffractometer, the microstructure and phase composition of aluminum rod were measured and analyzed. The results indicate that the content of rare earth element Ce is between 0.05% -0.16% in the aluminum rod for electrical purpose. Its tensile strength is enhanced to some extent. The research also discovers that the tensile strength is enhanced remarkably with impurity element Si content increases. Because influence of Si is big to the conductivity, the Si content should be controlled continuously strictly in the aluminum for electrical purpose. Adding rare earth element Ce reduces the solid solubility of Si in the aluminum matrix, and the negative effect of Si on the aluminum conductor reduces effectively. So the limit of in Si content in aluminum rod for electrical purpose can be relaxed moderately.
基金financial supports from the National Key Research and Development Program of China(2017YFA0403804)the National Natural Science Foundation of China(51425402,51671073)。
文摘ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.
文摘This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−xBiCu solder joints were investigated.Bi-doping modified the microstructure of the solder joints by refining the primaryβ-Sn and eutectic phases.Bi-doping below 2 wt.%dissolved in theβ-Sn matrix and formed a solid solution,whereas Bi additions equal to or greater than 2 wt.%formed Bi precipitates in theβ-Sn matrix.Solid solution strengthening and precipitation strengthening mechanisms in theβ-Sn matrix increased the ultimate tensile strength and microhardness of the alloy from 35.7 MPa and 12.6 HV to 55.3 MPa and 20.8 HV,respectively,but elongation decreased from 24.6%to 16.1%.The fracture surface of a solder joint containing 2 wt.%Bi was typical of a brittle failure rather than a ductile failure.The interfacial layer of all solder joints comprised two parallel IMC layers:a layer of Cu6Sn5 and a layer of Cu3Sn.The interfacial layer was thinner and the shear strength was greater in SAC305−xBiCu joints than in SAC305Cu solder joints.Therefore,small addition of Bi refined microstructure,reduced melting temperature and improved the mechanical performance of SAC305Cu solder joints.
文摘Rare earth -containing PSBR sheet was prepared by reaction of rare earth alkoxide with quaternary ammonium salt of pyridine modified SBR (PSBR) latex, and then it was blended with natural rubber (NR) to produce rare earth - containing composite elastomer. It is found that mechanical performance can be improved remarkably. Analyzed by infrared spectrometry (IR), differential scanning calorimetry (DSC) and cross-linking densitometry, the relationship between structure and performance was discussed.
基金the National Natural Science Foundation of China(No.51771150)the National Key Research and Development Program of China(No.2016YFB0701303)+1 种基金the Aeronautical Science Foundation of China(No.201936053001)the Research Fund of the State Key Laboratory of Solidification(NWPU),China(No.2019-TS-07)。
文摘Solid-state diffusion bonding(DB)of TiAl alloy and Ti2 AlNb alloy was carried out using pure Ti as an interlayer at 1000℃under 20 MPa for 60-120 min.The effects of bonding times on the interfacial microstructure and mechanical performance of the TiAl/Ti/Ti_(2)AlNb bonded joints at room temperature(RT)were investigated detailly.The results demonstrated that the diffusion layers(DLs)mainly consisted of four characteristic layers,(Ⅰ)single coarseα_(2)phase adjacent TiAl alloy,(Ⅱ)single refinedα_(2)phase at the bonding interface,(Ⅲ)equiaxed/acicularα_(2)phase embedded inβphase adjacent Ti_(2)AtNb alloy and(IV)both equiaxedα_(2)phase and acicular O phase embedded inβphase adj acent Ti_(2)AlNb alloy,respectively.The thickness of the four layers increased with the increasing of the bonding time.The growth of DLs is controlled by diffusion and the reaction rate constant k for regionⅠ,Ⅱ,ⅢandⅣare 1.22×10^(-6),1.27×10^(-6),2.6×10^(-7)and 7.7×10^(-7)m·s^(-1/2),respectively.Meanwhile,the interfaceα_(2)grain grows up without texture.The maximum tensile strength of 281 MPa was maintained at1000℃for 90 min under the pressure of 20 MPa.Consequently,the phase transformation and dynamic recrystallization behavior of the DLs were discussed.
基金This work was supported by the National Natural Science Foundation of China[Grant Nos.11790283,51978587,51708457]the Program of Introducing Talents of Discipline to Universities(111 Project)[Grant No.B16041].
文摘Motivated by the huge practical engineering demand for the fundamental understanding of mechanical characteristics of high-speed railway infrastructure,a fullscale multi-functional test platform for high-speed railway track–subgrade system is developed in this paper,and its main functions for investigating the mechanical performance of track–subgrade systems are elaborated with three typical experimental examples.Comprising the full-scale subgrade structure and all the five types of track structures adopted in Chinese high-speed railways,namely the CRTS I,the CRTS II and the CRTS III ballastless tracks,the double-block ballastless track and the ballasted track,the test platform is established strictly according to the construction standard of Chinese high-speed railways.Three kinds of effective loading methods are employed,including the real bogie loading,multi-point loading and the impact loading.Various types of sensors are adopted in different components of the five types of track–subgrade systems to measure the displacement,acceleration,pressure,structural strain and deformation,etc.Utilizing this test platform,both dynamic characteristics and long-term performance evolution of high-speed railway track–subgrade systems can be investigated,being able to satisfy the actual demand for large-scale operation of Chinese high-speed railways.As examples,three typical experimental studies are presented to elucidate the comprehensive functionalities of the full-scale multi-functional test platform for exploring the dynamic performance and its long-term evolution of ballastless track systems and for studying the long-term accumulative settlement of the ballasted track–subgrade system in high-speed railways.Some interesting phenomena and meaningful results are captured by the developed test platform,which provide a useful guidance for the scientific operation and maintenance of high-speed railway infrastructure.
基金financial support from the National Key Research and Development Program of China (No.2019YFE0111000)the National Natural Science Foundation of China (NSFC,Nos.51903253,51903257)+2 种基金Natural Science Foundation of Guangdong Province of China (Nos.2019A1515011150,2019A1515011258)Macao University of Science and Technology Foundation (No.FRG-19-003-SP)the Science and Technology Development Fund of Macao (Nos.FDCT 0009/2019/A,0083/2019/A2,0007/2019/AKP)。
文摘Nature consists of various soft tissues with well-ordered hierarchical anisotropic structures, which play essential roles in biological systems to exhibit particular functions. Mimicking bio-tissues, synthetic hydrogels with anisotropic structures have received considerable attention in recent years. However, existing approaches to fabricate anisotropic hydrogels often require complicated procedures, which are timeconsuming and labor-demanding. Inspired by the dry-induced crystallization phenomenon, we report a simple yet effective prestretching-drying-swelling method to afford anisotropic crystalline polyvinyl alcohol hydrogels. Owing to the distinct anisotropic microstructure, the hydrogels demonstrate excellent mechanical properties with noticeable directional distinction. It is revealed that both the enhancing of pre-orientation strain and the extending of heating time make the hydrogels with better mechanical properties and more remarkable anisotropicity. Owing to the anisotropically aligned structure, the hydrogels exhibit remarkably differential ionic conductivity: the difference between the parallel and vertical conductivity of the same sample can reach as high as 6.6 times, making the materials possible candidates as nano-conductive materials. We anticipate that this simple yet effective approach may become highly useful for fabricating oriented hydrogels and endow the materials with more promising application prospects in the future.
基金Funded by the Program of Innovative Team of the Ministry of Education of China(No.IRT13089)the National Natural Science Foundation of China(No.51078307)
文摘The aim of this study is to provide the quantificational change laws of strength,stiffness,and deformation capacity of frost-damaged concrete relating to a united index,the data were obtained by different researchers.Then the index of relative compressive strength（RCS） was introduced as the indicator of frost damage and a large number of mechanical performance testing data of frost-damaged concrete were collected and analyzed.By curve fitting,the correlations between RCS and the initial elastic modulus,the strain at peak compressive stress,and biaxial compressive strength,and tensile strength,and the strain at peak tensile stress were established.Thereafter,the analytical stress-strain response of frost-damaged concrete under monotonic loading was presented using RCS and compared with that of the experimental data.Moreover,an isotropic elastoplastic damage model of frost-damaged concrete subjected to repeated loading was established.Finally,we can systematically estimate the effects of frost-damage on the mechanical performance of concrete,which can be provided for the numerical simulation of frost-damaged concrete structures.
基金This work was supported by the National Natural Science Foundation of China(Grants Nos.12122212,11932017,11772054,and 11772055).
文摘Silk protein builds one of the strongest natural fibers based on its complex nanocomposite structures.However,the mechanical performance of silk protein,related to its molecular structure and packing is still elusive.In this study,we constructed an atomistic silk protein network model,which reproduces the extensive connection topology of silk protein with structure details of theβ-sheet crystallites and amorphous domains.With the silk protein network model,we investigated the structure evolution and stress distribution of silk protein under external loading.We found a pre-stretching treatment during the spinning process can improve the strength of silk protein.This treatment improves the properties of silk protein network,i.e.,increases the number of nodes and bridges,makes the nodes distributed homogeneously,and induces the bridges in the network well aligned to the loading direction,which is of great benefit to the mechanical performances of silk protein.Our study not only provides a realized atomistic model for silk protein network that well represents the structures and deformations of silk proteins under loading,but also gains deep insights into the mechanism how the pre-loading on silk proteins during spinning improves the mechanical properties of silk fibers.
文摘Nitrogen doped diamond-like carbon （DLC：N） films were prepared by electron cyclotron resonance chemical vapor deposition （ECR-CVD） on polycrystalline Si chips. Film thickness is about 50 nm. Auger electron spectroscopy （AES） was used to evaluate nitrogen content, and increasing N2 flow improved N content from 0 to 7.6%. Raman and X-ray photoelectron spectroscopy （XPS） analysis results reveal CN-sp^3C and N-sp^2C structure. With increasing the N2 flow, sp^3C decreases from 73.74% down to 42.66%, and so does N-sp^3C from 68.04% down to 20.23%. The hardness decreases from 29.18 GPa down to 19.74 GPa, and the Young＇s modulus from 193.03 GPa down to 144.52 GPa.
文摘On the basis of test, nonlinear finite element analysis of reinforcedconcrete (R. C) short-limb shear walls under monotonic horizontal load are carried out by ANSYSprogram in order to understand the evolution of cracking, deformation and failure course of thespecimens. At the same time, the results of numerical calculation are compared with the results oftest. The results indicate that, under monotonic horizontal load the failures of the specimens withflange wall and without flange wall all occur at the intersections of lintel bottom and limb ofwall, the failures also occur at the bottom of limb; the load-displacement curve of wall withoutflange is steeper than that of wall with flange, and the ductility is worse than that of wall withflange; the results, such as cracking, deformation, yield load and so on of finite element analysisagree well with the results of test. These results provide theoretical basis of study andapplication of R. C short-limb shear wall.
基金Funded by the Joint Fund of Ministry of Education for Equipment Pre-research(No.6141A02022250)the Fundamental Research Funds for the Central Universities,China(No.WUT:2021III003XZ)。
文摘The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on the mechanical performance of SiCf/phenolic composites after high-temperature pyrolysis was studied through flexural performance test.The results show that the composite material has good thermal stability and high-temperature mechanical properties.After static ablation at 1400℃ for 15 minutes,the flexural strength of the composite material reaches 286 MPa,which is still 7.3%higher than at room temperature,indicating that the composite material still has good mechanical properties even after heat treatment at 1400℃.
基金This work was supported by National Key Research and Development Project(2020YFB1600102,2020YFA0714302)National Natural Science Foundation of China(51878164,51922030,52208430)+2 种基金Fundamental Research Funds for the Central Universities of China(2242022R10059)Natural Science Foundation of Jiangsu Province(SBK2021042206)Southeast University“Zhongying Young Scholars”Project,and Shuangchuang Program of Jiangsu Province(JSSCBS20210058).
文摘In the induction heating of airport pavement to remove snow and ice,soft magnetic geopolymer composite(SMGC)can be used to gather the dissipated electromagnetic energy,thus enhancing the energy utilization efficiency.The aim of this work is to analyze the influence mechanism of iron powder content on the electromagnetic and mechanical performance of SMGC,so as to provide theoretical guidance for the design of soft magnetic layer within airport pavement structure.The results show that the increase of iron powder content reduces the resistance and magnetoresistance of SMGC by decreasing the content of non-magnetic phases between iron powder.However,the reduction of iron powder spacing also provides a shorter transmission path for the inter-particle eddy currents in the SMGC specimen,which enhances the exchange coupling between iron powder,thus increasing the electromagnetic loss.Therefore,the compatibility between magnetic permeability and electromagnetic loss should be considered comprehensively in the mix design of SMGC.In addition,although iron powder can enhance the mechanical properties of SMGC by improving the density of geopolymer matrix,the excessive amount of iron powder can lead to a weak interfacial transition zone between geopolymer matrix and iron powder.According to the induction heating results,optimized SMGC can improve the energy transfer efficiency of induction heating by 24.03%.
