Lithium(Li)metal is believed to be the“Holy Grail”among all anode materials for next-generation Li-based batteries due to its high theoretical specific capacity(3860 mAh/g)and lowest redox potential(−3.04 V).Disappo...Lithium(Li)metal is believed to be the“Holy Grail”among all anode materials for next-generation Li-based batteries due to its high theoretical specific capacity(3860 mAh/g)and lowest redox potential(−3.04 V).Disappointingly,uncontrolled dendrite formation and“hostless”deposition impede its further development.It is well accepted that the construction of three-dimensional(3D)composite Li metal anode could tackle the above problems to some extent by reducing local current density and maintaining electrode volume during cycling.However,most strategies to build 3D composite Li metal anode require either electrodeposition or melt-infusion process.In spite of their effectiveness,these procedures bring multiple complex processing steps,high temperature,and harsh experimental conditions which cannot meet the actual production demand in consideration of cost and safety.Under this condition,a novel method to construct 3D composite anode via simple mechanical modification has been recently proposed which does not involve harsh conditions,fussy procedures,or fancy equipment.In this mini review,a systematic and in-depth investigation of this mechanical deformation technique to build 3D composite Li metal anode is provided.First,by summarizing a number of recent studies,different mechanical modification approaches are classified clearly according to their specific procedures.Then,the effect of each individual mechanical modification approach and its working mechanisms is reviewed.Afterwards,the merits and limits of different approaches are compared.Finally,a general summary and perspective on construction strategies for next-generation 3D composite Li anode are presented.展开更多
Severe segregation and poor rheological properties in crumb rubber(CR)modified asphalt(CRMT)were addressed by investigating the performance improvement effect of organic expanded vermiculite(OEV)as a comodifier,while ...Severe segregation and poor rheological properties in crumb rubber(CR)modified asphalt(CRMT)were addressed by investigating the performance improvement effect of organic expanded vermiculite(OEV)as a comodifier,while the modification mechanism of the resulting asphalt was also elucidated.Vermiculite was thermally treated and chemically modified to enhance its interaction with the asphalt matrix and CR,improving dispersion and interfacial properties.CR/OEV/furfural extract oil(OIL)composite modified asphalt(COMT)was prepared in this study.The compatibility and microscopic mechanism of modified asphalt were characterized by dynamic shear rheological test,multiple stress creep recovery(MSCR)test,BBR test,thermal segregation test,fluorescent scanning test,infrared spectroscopy,and gel permeation chromatography.Rheological tests showed that the modified asphalt exhibited improved high-temperature stability,with increased G*/sin(δ)values,and better low-temperature flexibility.Storage stability tests showed a reduced softening point difference,indicating enhanced homogeneity and reduced segregation.Microscopic analysis revealed that OEV effectively optimized the microstructure of the composite system by promoting the uniform dispersion of CR within the asphalt matrix.Furthermore,the macromolecular weight of COMT was increased by 31.9%,molecular weight analysis confirmed a higher proportion of large molecular weight fractions,contributing to enhanced rheological properties and compatibility.These findings demonstrated that OEV significantly improved the performance and durability of CRMT,providing a promising approach for sustainable road construction.展开更多
In the corrosive environment of carbonaceous mudstone,the mechanical properties of grouting materials in the anchorage section of anchor bolts continue to deteriorate.In response,a cement-based modified anchoring grou...In the corrosive environment of carbonaceous mudstone,the mechanical properties of grouting materials in the anchorage section of anchor bolts continue to deteriorate.In response,a cement-based modified anchoring grouting material(MAGM)with high corrosion resistance was developed.The results reveal that compared with those of ordinary Portland cement(OPC)grouting material,the compressive strength,tensile strength,and shear stress peak of the MAGM increased by 85.9%,44.4%and 45.4%,respectively,after 28 d of corrosion in a carbonaceous mudstone solution.Waterborne epoxy resin and curing agent create a network membrane structure under the action of nano-Al_(2)O_(3)to protect the cement hydration products.In the corrosive environment of carbonaceous mudstone,corrosion products formed on the surface of the stone body have adsorbed onto the reticular membrane structure,filling the pores of the stone body and slowing the erosion rate of ions.After 365 d of application of MAGM and OPC in the corrosive environment of a carbonaceous mudstone slope,the peak shear stress of MAGM is,on average,55.3%greater than that of OPC.展开更多
Steel slag(SS)accumulates unavoidably due to its complex and unstable composition,high production volumes,and limited value-added resource utilization.Single or multiple interface modifiers were proposed to enhance th...Steel slag(SS)accumulates unavoidably due to its complex and unstable composition,high production volumes,and limited value-added resource utilization.Single or multiple interface modifiers were proposed to enhance the properties of SS through high-speed dispersion,transforming its inherent hydrophilic and oleophobic characteristics into hydrophily and lipophilicity.The modification effects were innovatively assessed by observing the color changes of modified steel slag solutions following the dissolution-settlement equilibrium constant.This approach avoided human-induced errors and improved estimated accuracy in conformance with conventional methods such as oil absorption value,activation index,sedimentation volume,and lipophilicity.The hydrolysis of 3-aminopropyltriethoxysilane(KH)generated–Si(OH)_(3)structure to form hydrogen or covalent bonds with active substances(OH groups)from SS.Concurrently,SS underwent encapsulation via Si–O–Si structure resulting from the dehydration of–Si(OH)_(3).The stearic acid coupling agent(SA),aluminate coupling agent(AC),and titanate coupling agent(TN)underwent chemical reactions with Ca(OH)_(2),Al(OH)_(3),and CaCO_(3)in SS.The acidic SA primarily created stable chemical bonds and acted as a supplement due to its package,reducing surface activity and hydrophilicity while enhancing lipophilicity.Specifically,the optimal modification effect was obtained at 3 wt.%SA.Consequently,3 wt.%SA was established as the benchmark for multiple modifiers and the most effective combination was 3 wt.%SA and 3 wt.%AC.Compared with a single interface modifier,SA corroded the SS surface to provide numerous active sites for further modification by KH,AC,or TN,resulting in a more densely packed structure.In addition,more organic groups on SS prevent the proximity of other particles from agglomerating to achieve dispersion and a synergistic modification,laying a theoretical foundation of SS in a new pathway for organic composite materials.展开更多
To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt b...To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt by physical property index,microscopic morphology,rheological testing,and infrared spectroscopy on multiple scales.The results show that the best preparation process for TB-modified asphalt is stirring at 260℃ for 4 h at 400 rpm,which significantly reduces the modification time of the asphalt.From a physical property viewpoint,the TB composite-modified asphalt sample with 5% styrene-butadiene-styrene(SBS)+1% aromatics+0.1% sulfur exhibits high-comprehensive,high-and low-temperature properties.More-over,its crosslinked mesh structure comprises black rubber particles uniformly interwoven in the middle,which further enhances the performance of the asphalt and results in an excellent performance formulation.In addition,the sample with 5%SBS content has a higher G*value and smaller δ value than that with 3%SBS content,indicating that its high-temperature resistance is improved.The effect of adding 3%SBS content on the viscoelastic ratio is,to some extent,less than that caused by 20% rubber powder.展开更多
Calcium carbonate,which is widely employed as a filler added into the polymer matrix,has large numbers of applications owing to the excellent properties such as low cost,non-toxicity,high natural reserves and biocompa...Calcium carbonate,which is widely employed as a filler added into the polymer matrix,has large numbers of applications owing to the excellent properties such as low cost,non-toxicity,high natural reserves and biocompatibility.Nevertheless,in order to obtain the good filling effect,calcium carbonate needs to be surface modified by organic molecules so as to enhance the dispersion and compatibility within the composites.This review paper systematically introduces the theory,methods,and applications progress of calcium carbonate with surface modification.Additionally,the key factors that affect the properties of the composites as well as the current difficulties and challenges are highlighted.The current research progress and potential application prospects of calcium carbonate in the fields of plastics,rubber,paper,medicine and environmental protection are discussed as well.Generally,this review can provide valuable reference for the modification and comprehensive utilization of calcium carbonate.展开更多
The effect of the rare earth cerium （Ce） on the hypereutectic Al-Si alloy under different casting states have been studied by optical microscope and quantitative image analysis. It is found that the size and the qua...The effect of the rare earth cerium （Ce） on the hypereutectic Al-Si alloy under different casting states have been studied by optical microscope and quantitative image analysis. It is found that the size and the quantity of primary silicon in castings decrease with the increase of added Ce in the melt. Meanwhile primary silicon changes from branched shape to fine facetted shape. Although the modification on eutectic silicon in castings also improves with the increase of added Ce in the melt, the effect of modification on eutectic silicon away from primary silicon is more obvious than that on eutectic silicon close to primary silicon. The modification mechanism was analyzed in detail by means of scanning electron microscope equipped with energy dispersive analysis of X-ray and thermodynamics analysis, which included the analysis on the change in standard Gibbs energy of reaction and reaction equilibrium.展开更多
Loess disintegration can lead to geotechnical engineering problems,e.g.,slope erosion,wetting-induced landslide,and hydroconsolidation.Microbially induced calcite precipitation(MICP)technique is a potential loess rein...Loess disintegration can lead to geotechnical engineering problems,e.g.,slope erosion,wetting-induced landslide,and hydroconsolidation.Microbially induced calcite precipitation(MICP)technique is a potential loess reinforcing method.This study investigated the physical-mechanical properties of MICP-treated loess and then explored the mechanism of loess modification by MICP.Here,loess first underwent MICP treatment,i.e.,mixing loess with Sporosarcina pasteurii and cementation solution(CS).Then,the effects of the CS concentration(0.2,0.6,0.8,and 1 M)on the physical and mechanical properties of the MICP-treated loess were tested.Finally,the static contact angle test,scanning electron microscopy(SEM),and X-ray diffractometry(XRD)were conducted to study the mechanism of MICP treatment on loess.Results showed the following property changes of loess after MICP treatment:the liquid limit decreased by 1.7%,the average particle size increased from 6 to 47μm,the specific gravity decreased from 2.65 to 2.43,the unconfined compressive strength increased from 37 to 71 k Pa,and the disintegration time increased from 10 to 25 min.Besides,the shear strength also increased,and the shear strength parameters(cohesion c and internal friction angle?)varied with the CS concentration.The static contact angle tests indicated that the water absorption ability of loess was reduced after MICP treatment.SEM and XRD results verified that the CaCO_(3)from MICP was attributed to the above results.The above findings explained the mechanism of MICP treatment of loess:the CaCO_(3)coats and cements the particles,and fills the pores of loess,improving the strength and water stability of loess.展开更多
A model of liquid ZA27 cast alloy is established according to molecular dynamics theory and an atomic structural model of co-existent a phase and liquid is also presented by means of computer programming. Recursion me...A model of liquid ZA27 cast alloy is established according to molecular dynamics theory and an atomic structural model of co-existent a phase and liquid is also presented by means of computer programming. Recursion method is adopted to calculate the electronic structure of RE (rare earth) in grains and around phase boundaries respectively. The calculation shows that RE is more stable around phase boundaries than in grains, which explains the fact that the solution of RE in a phase is less, and RE mainly aggregates in front of phase boundary. The calculations of bonding order integrals also show that RE in front of phases hardly solidify onto the grain surfaces as active element so as to prevent grains growth and refine the grains. As a result, the modification mechanism of RE may be explained from the view of electronic structure.展开更多
The model of the liquid-phase ZA27 alloys was set up by molecular dynamics theory. The atomic structure of phase, RE-compounds, and the phase-liquid interface in ZA27 alloys were constructed by computer programming. E...The model of the liquid-phase ZA27 alloys was set up by molecular dynamics theory. The atomic structure of phase, RE-compounds, and the phase-liquid interface in ZA27 alloys were constructed by computer programming. Electronic structures of phase with rare earth elements dissolved and of phase-liquid interfaces with rare earth elements enrichment in ZA27 casting alloys were investigated by using the Recursion method. The ESE energy of RE elements and the structure energy of RE-compounds, phase, and the liquid-phase ZA27 alloys were calculated. The results show that rare earth elements are more stable to be in the phase interface than in phase, which explains the fact of very small solid solubility of rare earth elements in phase, and the enrichment in the solid-liquid growth front. This makes dendrite melt and break down, dissociate and propagate. RE-compounds can act as heterogeneous nuclei for phase, leading to phase refinement. All above elucidates the modification mechanism of rare earth elements in zinc-aluminum casting alloys at electronic level.展开更多
A near eutectic Al−12.6Si alloy was developed with 0.0wt%,2.0wt%,4.0wt%,and 6.0wt%Al−5Ti−1B master alloy.The micro-structural morphology,hardness,tensile strength,elongation,and fracture behaviour of the alloys were s...A near eutectic Al−12.6Si alloy was developed with 0.0wt%,2.0wt%,4.0wt%,and 6.0wt%Al−5Ti−1B master alloy.The micro-structural morphology,hardness,tensile strength,elongation,and fracture behaviour of the alloys were studied.The unmodified Al−12.6Si al-loy has an irregular needle and plate-like eutectic silicon(ESi)and coarse polygonal primary silicon(PSi)particles in the matrix-likeα-Al phase.The P_(Si),E_(Si),andα-Al morphology and volume fraction were changed due to the addition of the Al−5Ti−1B master alloy.The hardness,UTS,and elongation improved due to the microstructural modification.Nano-sized in-situ Al3Ti particles and ex-situ TiB_(2)particles caused the mi-crostructural modification.The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time.The Al−5Ti−1B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.展开更多
In recent years,with the improvement of the requirements of road performance,modified emulsified asphalts with better performance has gradually replaced the emulsified asphalt and become the primary material for road ...In recent years,with the improvement of the requirements of road performance,modified emulsified asphalts with better performance has gradually replaced the emulsified asphalt and become the primary material for road maintenance.This paper introduces the modified emulsified asphalt materials commonly used in pavement maintenance projects,definitions and modified mechanisms of polymerized styrene butadiene rubber(SBR)modified emulsified asphalt,styrene butadiene styrene block polymer(SBS)modified emulsified asphalt and waterborne epoxy resin(WER)modified emulsified asphalt are summarized.The analysis focused on comparing the effects of modifiers,preparation process,auxiliary additives,and other factors on the performance of modified emulsified asphalt.In this paper,it is considered that the greatest impact on the performance of emulsified asphalt is the modifier,emulsifier mainly affects the speed of breaking the emulsion,stabilizers on the basic performance of emulsified asphalt evaporative residue is small;and when the modifier is distributed in the asphalt in a network,the dosage at this time is the recommended optimum dosage.Finally,this study recommends that in the future,the polymer-asphalt compatibility can be improved through composite modification,chemical grafting and other methods to continue to develop broader applicability and better performance of modified emulsified asphalt.展开更多
Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is...Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is restricted due to its unsatisfactory oxidant activation efficiency.Fortunately,recently remarkable research on deep activation mechanisms and modification of MNO_(x)have been undertaken to improve its reactivity.Herein,modification enhancement mechanisms of MNO_(x)to efficiently degrade various organic contaminants were discussed and highlighted,including metal doping,coupling with other metal oxides,composite with carbonaceous material,and compounding with other support.The activation mechanisms of different MNO_(x)and derivative-modified material(such as doped MNO_(x),metal oxide-MNO_(x)hybrids,and MNO_(x)-carbonaceous material hybrids)were summarized in great details,which was specifically categorized into both radical and non-radical pathways.The effects of pH,inorganic ions,and natural organic matter on degradation reactions are also discussed.Finally,future research directions and perspectives are presented to provide a clear interpretation on the MNO_(x)initiated AOPs.展开更多
Effects of mischmetal（RE） and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential sc...Effects of mischmetal（RE） and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential scanning calorimetry（DSC）, optical microscopy（OM）, scanning electron microscopy（SEM）. The DSC results showed that an addition of RE decreased the eutectic temperature and caused supercooling, promoting the nucleation of eutectic Si crystals. In addition, the maximum temperature of the first endothermic peak varied with the different RE contents, which had a good correlation with the microstructural modification of the eutectic Si phase. The α-Al dendrites were well refined by increasing the cooling rate or adding 0.08 wt.% of Ti. When 0.05 wt.% RE was added to the Al-5Si-0.08 Ti alloy, the morphology of eutectic Si phase was transformed from coarse platelet to fine fibers and the mechanical properties of the resulting welding rod were well improved. Whereas, when excess RE was added, a large number of β-Fe phases appeared and the aspect ratios of β-Fe phases increased. The morphologies and chemical components of two kinds of RE-containing intermetallic compounds（IMCs） were also discussed.展开更多
In order to reveal the surface modification mechanism of fine coal by electrochemical methods, the structural changes of the coal surface before and after electrochemical modification were investigated by Fourier Tran...In order to reveal the surface modification mechanism of fine coal by electrochemical methods, the structural changes of the coal surface before and after electrochemical modification were investigated by Fourier Transform In- frared Spectra (FTIR) and Raman Spectra. The results show that under certain electrochemical conditions, the oxy- gen-containing functional group in the coal structure and the oxygen content of absorption could be reduced and the floatability of coal improved. At the same time, the sulfur in the coal was reduced to the hydrophilic S2– which could be separated easily from coal. Thus electrochemical modification methods could be used to change the structure and func- tional group on the coal surface and to enhance the floatability of coal.展开更多
Modification conditions determine the surface topography and the active material phase composition of a catalyst.To study the influence of modification on a carbon-based sorbent,coconut husk activated carbon(AC)which ...Modification conditions determine the surface topography and the active material phase composition of a catalyst.To study the influence of modification on a carbon-based sorbent,coconut husk activated carbon(AC)which was activated using HNO_(3)and modified by FeSO4 and Fe(NO_(3))_(3)was examined.The pore textures and surface chemical characteristics of the carbon materials were examined by scanning electron microscopy(SEM),Brunner-Emmet-Teller(BET),X-ray diffraction(XRD)and Fourier transform infrared(FTIR)spectroscopy.The surface topography,the pore structure,active materials,and functional groups of AC,AC modificated by HNO3(HNO3/AC for short),and AC modificated by FeSO4 and Fe(NO3)3(Fe/AC for short)were systematically studied.Subsequently,the mechanism of modifying the conditions for the carbon materials was determined.Results showed that the surface micro topography of HNO3/AC became unsystematic and disordered.After modification with FeSO4,the ferriferous oxide was mainly present as a near-spherical crystal.Ferriferous oxides from Fe(NO_(3))_(3)modification mainly exhibited a plate shape.HNO_(3)modification could enlarge the pores but decrease the specific surface area of AC.FeSO_(4)modification resulted in a new net post structure in the pore canal of AC.Fe(NO_(3))_(3)modification caused the pore space structure to develop in the interior,and a higher calcination temperature was useful for ablation.The ash content of the AC was substantially reduced upon HNO_(3)modification.Upon FeSO_(4)modification,α-FeOOH,α-Fe_(2)O_(3)andγ-Fe_(2)O_(3)coexisted under the condition of a lower concentration of FeSO_(4)and a lower calcination temperature,and a higher FeSO_(4)concentration and calcination temperature generated moreα-Fe_(2)O_(3).The same Fe(NO_(3))_(3)modification and a higher calcination temperature were beneficial to the minor chipping formation ofγ-Fe_(2)O_(3).A higher Fe(NO_(3))_(3)loading produced a lower graphitization degree.HNO_(3)modification formed various new oxygen-containing functional groups and few nitrogen-containing groups.Based on the cover,FeSO_(4)and Fe(NO_(3))_(3)modification could decrease the oxygen-containing and nitrogen-containing functional groups.These results could optimize the modification condition and improve physical and chemical properties of carbon-based sorbents.展开更多
In order to investigate the influening factors of organic modification procedure and find out connections between organic modification and the properties of bentonite greases, organic montmorillonite(OMMT) thickeners ...In order to investigate the influening factors of organic modification procedure and find out connections between organic modification and the properties of bentonite greases, organic montmorillonite(OMMT) thickeners with different surfactant dosages and constituents were synthesized through intercalation reaction between sodium montmorillonite(NaM MT) and quaternary ammonium surfactants in aqueous solvents. The lubricating greases were prepared with the resulting organoclays, while the penetration and oil separation of lubricating greases were evaluated, respectively. The surface modification process of montmorillonite(MMT) was analyzed and the thickening mechanism of OMMT was discussed in this study. The experimental results showed that, with an increasing amount of surfactant, the basal spacing between the clay platelets was increasing and the structure of modifier molecules layer in the interlayer was changing from lateral bilayer to paraffin-type bilayer. The optimal properties of lubricating greases were achieved, when the structure of surfactant molecules loaded in the interlayer was the paraffin-type monolayer, which meant that the dosage of modifier was equal to 120—140 mmol/(100g). Meanwhile, it was found that the thickening performance, colloid stability, anti-wear and friction-reducing performance of lubricating greases were improved, when the surfactants were mixed with octadecyl trimethyl ammonium chloride(OTAC) and hexadecyl trimethyl ammonium chloride(HTAC). And the optimum mole ratio of two surfactants is was 1:1.展开更多
Dysprosium composite cobalt ferrite ionic magnetic fluids were prepared by precipitation in the presence of Tri-sodium citrate. Influence of dysprosium modification on magnetic property is studied. The result shows th...Dysprosium composite cobalt ferrite ionic magnetic fluids were prepared by precipitation in the presence of Tri-sodium citrate. Influence of dysprosium modification on magnetic property is studied. The result shows that magnetic response toward exterior magnetic field can be improved by adding Dy3+. Studies also show that the increase of reaction temperature may improve the modification effect of dysprosium. By adding dysprosium ions, the average diameter of the magnetic nanoparticles will be decreased evidently. It is clear that the particles appear as balls. Cobalt ferrite with sizes of 12-15 nm, rare earth composite cobalt ferrite with sizes of 6-8 nm.展开更多
A calcium sulfate whisker （CSW） coated with glutaraldehyde crosslinked chitosan （GACS） was prepared to reinforce polyvinyl chloride （PVC） in this study. The results show that the optimum concentration of both ch...A calcium sulfate whisker （CSW） coated with glutaraldehyde crosslinked chitosan （GACS） was prepared to reinforce polyvinyl chloride （PVC） in this study. The results show that the optimum concentration of both chitosan （CS） and glutaraldehyde （GA） is 0.05 wt%. The tensile strength, impact strength, flexural modulus and vicat softening temperature of the PVC composite with 12 wt% of modified CSW are in- creased by 1 Z5%, 40.4%, 0.8% and 3.8% compared with those of the PVC composite with 12 wt~ of unmodified CSW, and by 2.9%, 42.4%, 2Z1% and 6.8% compared with those of pure PVC, respectively. The dynamic mechanical analysis results indicate that the modified CSW/PVC composite exhibits much higher storage modulus and glass transition temperature than those of unmodified CSW/PVC composite and pure PVC. In addition, the modified CSW/PVC composite also demonstrates good thermal properties with a high rapidest decomposition temperature （Trvd） and char residue. The scanning electron microscopy images of tensile-fractured surfaces show that the modified CSW has a strong interfacial adhesion with PVC matrix.展开更多
To study the mechanism by which activated carbon is modified by HNO3 and Mn(NO3)2,the pore texture and surface chemical characteristics of carbon materials in coconut husk activated carbon(AC)were examined via scannin...To study the mechanism by which activated carbon is modified by HNO3 and Mn(NO3)2,the pore texture and surface chemical characteristics of carbon materials in coconut husk activated carbon(AC)were examined via scanning electron microscopy(SEM),Brunauer-Emmett-Teller(BET),X-ray diffraction(XRD),Fourier-transform infrared spectroscopy(FTIR),and X-ray photoelectron spectroscopy(XPS).After being modified by HNO3,the millipore character of AC became deformed,and the character of the adjacent pores remained consolidated.The surface manganites of Mn/AC-1 presented as block and reticular fiber structures,Mn/AC-2's surface manganites presented as petty mammock crystals,and Mn/AC-3's surface manganites were observed as gauze nanosheets that interlace to fill in the pore canal.Nitric acid modification was shown to enlarge surface pores but decrease the specific surface area of AC.Mn loading can be used to construct a new pore structure that,in turn,increased the total specific surface area as well as the specific surface area and the volume of the millipores.Mn/AC-2's pore structure was optimized at a calcination temperature of 500℃and a loading quantity of 5%.The ash content of AC was considerably reduced after modified by HNO3.The active materials for Mn/AC-1 mainly consisted of Mn3O4,with a few Mn2O3 crystals,whereas Mn/AC-2's materials were mainly Mn3O4 and some MnO crystals.Mn/AC-3 was exclusively composed of Mn3O4.HNO3 activation and Mn loading modification did not considerably affect the functional group species present on the catalyst.Modification conditions using the same loading quantities and higher calcination temperatures decreased the number of O—H and N—H bonds while conversely increasing the number of CC and C—O bonds.On the contrary,the use of a higher loading quantity while maintaining the same calcination temperature increased the number of O—H and N—H bonds.A higher loading quantity is beneficial for increasing Mn^4+species.A higher calcination temperature is beneficial for increasing Mn^3+species.The results can optimize the conditions under which Mn/AC catalyst modification occurs,thus improving the physical and chemical properties of carbon-based sorbents.展开更多
文摘Lithium(Li)metal is believed to be the“Holy Grail”among all anode materials for next-generation Li-based batteries due to its high theoretical specific capacity(3860 mAh/g)and lowest redox potential(−3.04 V).Disappointingly,uncontrolled dendrite formation and“hostless”deposition impede its further development.It is well accepted that the construction of three-dimensional(3D)composite Li metal anode could tackle the above problems to some extent by reducing local current density and maintaining electrode volume during cycling.However,most strategies to build 3D composite Li metal anode require either electrodeposition or melt-infusion process.In spite of their effectiveness,these procedures bring multiple complex processing steps,high temperature,and harsh experimental conditions which cannot meet the actual production demand in consideration of cost and safety.Under this condition,a novel method to construct 3D composite anode via simple mechanical modification has been recently proposed which does not involve harsh conditions,fussy procedures,or fancy equipment.In this mini review,a systematic and in-depth investigation of this mechanical deformation technique to build 3D composite Li metal anode is provided.First,by summarizing a number of recent studies,different mechanical modification approaches are classified clearly according to their specific procedures.Then,the effect of each individual mechanical modification approach and its working mechanisms is reviewed.Afterwards,the merits and limits of different approaches are compared.Finally,a general summary and perspective on construction strategies for next-generation 3D composite Li anode are presented.
基金supported by National Key R&D Program of China(2024YFF0510200)National Natural Science Foundation of China(52478438,52174237)+2 种基金Excellent Early Career Scientists form Germany(GZ1717)Science and Technology Project of Changsha-Outstanding Innovative Youth(kq2406007)Practice Innovation and Entrepreneurship Enhancement Program for Postgraduate of Changsha University of Science&Technology(CLSJCX24006).
文摘Severe segregation and poor rheological properties in crumb rubber(CR)modified asphalt(CRMT)were addressed by investigating the performance improvement effect of organic expanded vermiculite(OEV)as a comodifier,while the modification mechanism of the resulting asphalt was also elucidated.Vermiculite was thermally treated and chemically modified to enhance its interaction with the asphalt matrix and CR,improving dispersion and interfacial properties.CR/OEV/furfural extract oil(OIL)composite modified asphalt(COMT)was prepared in this study.The compatibility and microscopic mechanism of modified asphalt were characterized by dynamic shear rheological test,multiple stress creep recovery(MSCR)test,BBR test,thermal segregation test,fluorescent scanning test,infrared spectroscopy,and gel permeation chromatography.Rheological tests showed that the modified asphalt exhibited improved high-temperature stability,with increased G*/sin(δ)values,and better low-temperature flexibility.Storage stability tests showed a reduced softening point difference,indicating enhanced homogeneity and reduced segregation.Microscopic analysis revealed that OEV effectively optimized the microstructure of the composite system by promoting the uniform dispersion of CR within the asphalt matrix.Furthermore,the macromolecular weight of COMT was increased by 31.9%,molecular weight analysis confirmed a higher proportion of large molecular weight fractions,contributing to enhanced rheological properties and compatibility.These findings demonstrated that OEV significantly improved the performance and durability of CRMT,providing a promising approach for sustainable road construction.
基金Projects(52278439,51838001)supported by the National Natural Science Foundation of ChinaProject(2023RC3138)supported by the Science and Technology Innovation Plan Project of Hunan Province,China+2 种基金Project(21B0317)supported by the Natural Science Youth Project of Education Department of Hunan Province,ChinaProject(2022JJ40500)supported by the Natural Science Foundation of Hunan Province,ChinaProject(21KB13)supported by the Open Fund of Key Laboratory of Safety Control of Bridge Engineering,Ministry of Education(Changsha University of Science&Technology),China。
文摘In the corrosive environment of carbonaceous mudstone,the mechanical properties of grouting materials in the anchorage section of anchor bolts continue to deteriorate.In response,a cement-based modified anchoring grouting material(MAGM)with high corrosion resistance was developed.The results reveal that compared with those of ordinary Portland cement(OPC)grouting material,the compressive strength,tensile strength,and shear stress peak of the MAGM increased by 85.9%,44.4%and 45.4%,respectively,after 28 d of corrosion in a carbonaceous mudstone solution.Waterborne epoxy resin and curing agent create a network membrane structure under the action of nano-Al_(2)O_(3)to protect the cement hydration products.In the corrosive environment of carbonaceous mudstone,corrosion products formed on the surface of the stone body have adsorbed onto the reticular membrane structure,filling the pores of the stone body and slowing the erosion rate of ions.After 365 d of application of MAGM and OPC in the corrosive environment of a carbonaceous mudstone slope,the peak shear stress of MAGM is,on average,55.3%greater than that of OPC.
基金supported by the National Natural Science Foundation of China(U23A20605)Anhui Graduate Innovation and Entrepreneurship Practice Project(2022cxcysj090)+2 种基金China Baowu Low Carbon Metallurgy Innovation Foundation(BWLCF202202)the University Synergy Innovation Program of Anhui Province(GXXT-2020-072)the Outstanding Youth Fund of Anhui Province(2208085J19).
文摘Steel slag(SS)accumulates unavoidably due to its complex and unstable composition,high production volumes,and limited value-added resource utilization.Single or multiple interface modifiers were proposed to enhance the properties of SS through high-speed dispersion,transforming its inherent hydrophilic and oleophobic characteristics into hydrophily and lipophilicity.The modification effects were innovatively assessed by observing the color changes of modified steel slag solutions following the dissolution-settlement equilibrium constant.This approach avoided human-induced errors and improved estimated accuracy in conformance with conventional methods such as oil absorption value,activation index,sedimentation volume,and lipophilicity.The hydrolysis of 3-aminopropyltriethoxysilane(KH)generated–Si(OH)_(3)structure to form hydrogen or covalent bonds with active substances(OH groups)from SS.Concurrently,SS underwent encapsulation via Si–O–Si structure resulting from the dehydration of–Si(OH)_(3).The stearic acid coupling agent(SA),aluminate coupling agent(AC),and titanate coupling agent(TN)underwent chemical reactions with Ca(OH)_(2),Al(OH)_(3),and CaCO_(3)in SS.The acidic SA primarily created stable chemical bonds and acted as a supplement due to its package,reducing surface activity and hydrophilicity while enhancing lipophilicity.Specifically,the optimal modification effect was obtained at 3 wt.%SA.Consequently,3 wt.%SA was established as the benchmark for multiple modifiers and the most effective combination was 3 wt.%SA and 3 wt.%AC.Compared with a single interface modifier,SA corroded the SS surface to provide numerous active sites for further modification by KH,AC,or TN,resulting in a more densely packed structure.In addition,more organic groups on SS prevent the proximity of other particles from agglomerating to achieve dispersion and a synergistic modification,laying a theoretical foundation of SS in a new pathway for organic composite materials.
基金Funded by the National Natural Science Foundation of China(No.52278446)。
文摘To explore the best preparation process for terminal blend(TB)composite-modified asphalt and to filter its formulation with excellent performance,this study evaluates the performance of TB composite modified asphalt by physical property index,microscopic morphology,rheological testing,and infrared spectroscopy on multiple scales.The results show that the best preparation process for TB-modified asphalt is stirring at 260℃ for 4 h at 400 rpm,which significantly reduces the modification time of the asphalt.From a physical property viewpoint,the TB composite-modified asphalt sample with 5% styrene-butadiene-styrene(SBS)+1% aromatics+0.1% sulfur exhibits high-comprehensive,high-and low-temperature properties.More-over,its crosslinked mesh structure comprises black rubber particles uniformly interwoven in the middle,which further enhances the performance of the asphalt and results in an excellent performance formulation.In addition,the sample with 5%SBS content has a higher G*value and smaller δ value than that with 3%SBS content,indicating that its high-temperature resistance is improved.The effect of adding 3%SBS content on the viscoelastic ratio is,to some extent,less than that caused by 20% rubber powder.
基金Project(AA18242008)supported by the Guangxi Science&Technology Major Project,ChinaProject(HZXYKFKT201904)supported by the Opening Project of Guangxi Key Laboratory of Calcium Carbonate Resources Comprehensive Utilization,China。
文摘Calcium carbonate,which is widely employed as a filler added into the polymer matrix,has large numbers of applications owing to the excellent properties such as low cost,non-toxicity,high natural reserves and biocompatibility.Nevertheless,in order to obtain the good filling effect,calcium carbonate needs to be surface modified by organic molecules so as to enhance the dispersion and compatibility within the composites.This review paper systematically introduces the theory,methods,and applications progress of calcium carbonate with surface modification.Additionally,the key factors that affect the properties of the composites as well as the current difficulties and challenges are highlighted.The current research progress and potential application prospects of calcium carbonate in the fields of plastics,rubber,paper,medicine and environmental protection are discussed as well.Generally,this review can provide valuable reference for the modification and comprehensive utilization of calcium carbonate.
基金The work is financially supported by Shanghai Leading Academic Discipline Project (No. T0101)the Open Funds of Shanghai Key Laboratory of Metal Function Materials Research and Application.
文摘The effect of the rare earth cerium （Ce） on the hypereutectic Al-Si alloy under different casting states have been studied by optical microscope and quantitative image analysis. It is found that the size and the quantity of primary silicon in castings decrease with the increase of added Ce in the melt. Meanwhile primary silicon changes from branched shape to fine facetted shape. Although the modification on eutectic silicon in castings also improves with the increase of added Ce in the melt, the effect of modification on eutectic silicon away from primary silicon is more obvious than that on eutectic silicon close to primary silicon. The modification mechanism was analyzed in detail by means of scanning electron microscope equipped with energy dispersive analysis of X-ray and thermodynamics analysis, which included the analysis on the change in standard Gibbs energy of reaction and reaction equilibrium.
基金funded by the Beijing Natural Science Foundation(No.8214060)the National Natural Science Foundation of China(No.42107164)the 2021 Graduate Innovation Fund Project of China University of Geosciences,Beijing(No.ZD2021YC059)。
文摘Loess disintegration can lead to geotechnical engineering problems,e.g.,slope erosion,wetting-induced landslide,and hydroconsolidation.Microbially induced calcite precipitation(MICP)technique is a potential loess reinforcing method.This study investigated the physical-mechanical properties of MICP-treated loess and then explored the mechanism of loess modification by MICP.Here,loess first underwent MICP treatment,i.e.,mixing loess with Sporosarcina pasteurii and cementation solution(CS).Then,the effects of the CS concentration(0.2,0.6,0.8,and 1 M)on the physical and mechanical properties of the MICP-treated loess were tested.Finally,the static contact angle test,scanning electron microscopy(SEM),and X-ray diffractometry(XRD)were conducted to study the mechanism of MICP treatment on loess.Results showed the following property changes of loess after MICP treatment:the liquid limit decreased by 1.7%,the average particle size increased from 6 to 47μm,the specific gravity decreased from 2.65 to 2.43,the unconfined compressive strength increased from 37 to 71 k Pa,and the disintegration time increased from 10 to 25 min.Besides,the shear strength also increased,and the shear strength parameters(cohesion c and internal friction angle?)varied with the CS concentration.The static contact angle tests indicated that the water absorption ability of loess was reduced after MICP treatment.SEM and XRD results verified that the CaCO_(3)from MICP was attributed to the above results.The above findings explained the mechanism of MICP treatment of loess:the CaCO_(3)coats and cements the particles,and fills the pores of loess,improving the strength and water stability of loess.
基金Authors deeply appreciate the support from the National Natural Science Foundation of China(No.50275098)the Natural Science Foundation of Liaoning Province(No.20022031)
文摘A model of liquid ZA27 cast alloy is established according to molecular dynamics theory and an atomic structural model of co-existent a phase and liquid is also presented by means of computer programming. Recursion method is adopted to calculate the electronic structure of RE (rare earth) in grains and around phase boundaries respectively. The calculation shows that RE is more stable around phase boundaries than in grains, which explains the fact that the solution of RE in a phase is less, and RE mainly aggregates in front of phase boundary. The calculations of bonding order integrals also show that RE in front of phases hardly solidify onto the grain surfaces as active element so as to prevent grains growth and refine the grains. As a result, the modification mechanism of RE may be explained from the view of electronic structure.
文摘The model of the liquid-phase ZA27 alloys was set up by molecular dynamics theory. The atomic structure of phase, RE-compounds, and the phase-liquid interface in ZA27 alloys were constructed by computer programming. Electronic structures of phase with rare earth elements dissolved and of phase-liquid interfaces with rare earth elements enrichment in ZA27 casting alloys were investigated by using the Recursion method. The ESE energy of RE elements and the structure energy of RE-compounds, phase, and the liquid-phase ZA27 alloys were calculated. The results show that rare earth elements are more stable to be in the phase interface than in phase, which explains the fact of very small solid solubility of rare earth elements in phase, and the enrichment in the solid-liquid growth front. This makes dendrite melt and break down, dissociate and propagate. RE-compounds can act as heterogeneous nuclei for phase, leading to phase refinement. All above elucidates the modification mechanism of rare earth elements in zinc-aluminum casting alloys at electronic level.
基金The authors would also like to thank NIT,Durgapur RIG#2 project for financial support and the Director of National In-stitute of Technology Durgapur,India,for his continuous en-couragement.
文摘A near eutectic Al−12.6Si alloy was developed with 0.0wt%,2.0wt%,4.0wt%,and 6.0wt%Al−5Ti−1B master alloy.The micro-structural morphology,hardness,tensile strength,elongation,and fracture behaviour of the alloys were studied.The unmodified Al−12.6Si al-loy has an irregular needle and plate-like eutectic silicon(ESi)and coarse polygonal primary silicon(PSi)particles in the matrix-likeα-Al phase.The P_(Si),E_(Si),andα-Al morphology and volume fraction were changed due to the addition of the Al−5Ti−1B master alloy.The hardness,UTS,and elongation improved due to the microstructural modification.Nano-sized in-situ Al3Ti particles and ex-situ TiB_(2)particles caused the mi-crostructural modification.The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time.The Al−5Ti−1B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.
基金The authors acknowledge the financial support from National Natural Science Foundation of China(No.51968006).
文摘In recent years,with the improvement of the requirements of road performance,modified emulsified asphalts with better performance has gradually replaced the emulsified asphalt and become the primary material for road maintenance.This paper introduces the modified emulsified asphalt materials commonly used in pavement maintenance projects,definitions and modified mechanisms of polymerized styrene butadiene rubber(SBR)modified emulsified asphalt,styrene butadiene styrene block polymer(SBS)modified emulsified asphalt and waterborne epoxy resin(WER)modified emulsified asphalt are summarized.The analysis focused on comparing the effects of modifiers,preparation process,auxiliary additives,and other factors on the performance of modified emulsified asphalt.In this paper,it is considered that the greatest impact on the performance of emulsified asphalt is the modifier,emulsifier mainly affects the speed of breaking the emulsion,stabilizers on the basic performance of emulsified asphalt evaporative residue is small;and when the modifier is distributed in the asphalt in a network,the dosage at this time is the recommended optimum dosage.Finally,this study recommends that in the future,the polymer-asphalt compatibility can be improved through composite modification,chemical grafting and other methods to continue to develop broader applicability and better performance of modified emulsified asphalt.
基金the National Natural Science Foundation of China(Nos.52170088 and 52070133)for financial support。
文摘Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is restricted due to its unsatisfactory oxidant activation efficiency.Fortunately,recently remarkable research on deep activation mechanisms and modification of MNO_(x)have been undertaken to improve its reactivity.Herein,modification enhancement mechanisms of MNO_(x)to efficiently degrade various organic contaminants were discussed and highlighted,including metal doping,coupling with other metal oxides,composite with carbonaceous material,and compounding with other support.The activation mechanisms of different MNO_(x)and derivative-modified material(such as doped MNO_(x),metal oxide-MNO_(x)hybrids,and MNO_(x)-carbonaceous material hybrids)were summarized in great details,which was specifically categorized into both radical and non-radical pathways.The effects of pH,inorganic ions,and natural organic matter on degradation reactions are also discussed.Finally,future research directions and perspectives are presented to provide a clear interpretation on the MNO_(x)initiated AOPs.
基金Project supported by National Natural Science Foundation of China(51375233)Priority Academic Program Development(PAPD)of Jiangsu Higher Education InstitutionsChina Postdoctoral Science Foundation(2014M550289,2015T80548)
文摘Effects of mischmetal（RE） and/or Ti modifier on the microstructure including α-Al dendrites, eutectic Si phases and other secondary phases of Al-Si brazing and/or welding alloys were investigated by differential scanning calorimetry（DSC）, optical microscopy（OM）, scanning electron microscopy（SEM）. The DSC results showed that an addition of RE decreased the eutectic temperature and caused supercooling, promoting the nucleation of eutectic Si crystals. In addition, the maximum temperature of the first endothermic peak varied with the different RE contents, which had a good correlation with the microstructural modification of the eutectic Si phase. The α-Al dendrites were well refined by increasing the cooling rate or adding 0.08 wt.% of Ti. When 0.05 wt.% RE was added to the Al-5Si-0.08 Ti alloy, the morphology of eutectic Si phase was transformed from coarse platelet to fine fibers and the mechanical properties of the resulting welding rod were well improved. Whereas, when excess RE was added, a large number of β-Fe phases appeared and the aspect ratios of β-Fe phases increased. The morphologies and chemical components of two kinds of RE-containing intermetallic compounds（IMCs） were also discussed.
基金Project 50174054 supported by the National Natural Science Foundation of China
文摘In order to reveal the surface modification mechanism of fine coal by electrochemical methods, the structural changes of the coal surface before and after electrochemical modification were investigated by Fourier Transform In- frared Spectra (FTIR) and Raman Spectra. The results show that under certain electrochemical conditions, the oxy- gen-containing functional group in the coal structure and the oxygen content of absorption could be reduced and the floatability of coal improved. At the same time, the sulfur in the coal was reduced to the hydrophilic S2– which could be separated easily from coal. Thus electrochemical modification methods could be used to change the structure and func- tional group on the coal surface and to enhance the floatability of coal.
基金General Project of Science and Technology Plan of Yunnan Science and Technology Department,China(No.2019FB077)Open Fund of Key Laboratory of Ministry of Education for Metallurgical Emission Reduction and Comprehensive Utilization of Resources,China(No.JKF19-08)。
文摘Modification conditions determine the surface topography and the active material phase composition of a catalyst.To study the influence of modification on a carbon-based sorbent,coconut husk activated carbon(AC)which was activated using HNO_(3)and modified by FeSO4 and Fe(NO_(3))_(3)was examined.The pore textures and surface chemical characteristics of the carbon materials were examined by scanning electron microscopy(SEM),Brunner-Emmet-Teller(BET),X-ray diffraction(XRD)and Fourier transform infrared(FTIR)spectroscopy.The surface topography,the pore structure,active materials,and functional groups of AC,AC modificated by HNO3(HNO3/AC for short),and AC modificated by FeSO4 and Fe(NO3)3(Fe/AC for short)were systematically studied.Subsequently,the mechanism of modifying the conditions for the carbon materials was determined.Results showed that the surface micro topography of HNO3/AC became unsystematic and disordered.After modification with FeSO4,the ferriferous oxide was mainly present as a near-spherical crystal.Ferriferous oxides from Fe(NO_(3))_(3)modification mainly exhibited a plate shape.HNO_(3)modification could enlarge the pores but decrease the specific surface area of AC.FeSO_(4)modification resulted in a new net post structure in the pore canal of AC.Fe(NO_(3))_(3)modification caused the pore space structure to develop in the interior,and a higher calcination temperature was useful for ablation.The ash content of the AC was substantially reduced upon HNO_(3)modification.Upon FeSO_(4)modification,α-FeOOH,α-Fe_(2)O_(3)andγ-Fe_(2)O_(3)coexisted under the condition of a lower concentration of FeSO_(4)and a lower calcination temperature,and a higher FeSO_(4)concentration and calcination temperature generated moreα-Fe_(2)O_(3).The same Fe(NO_(3))_(3)modification and a higher calcination temperature were beneficial to the minor chipping formation ofγ-Fe_(2)O_(3).A higher Fe(NO_(3))_(3)loading produced a lower graphitization degree.HNO_(3)modification formed various new oxygen-containing functional groups and few nitrogen-containing groups.Based on the cover,FeSO_(4)and Fe(NO_(3))_(3)modification could decrease the oxygen-containing and nitrogen-containing functional groups.These results could optimize the modification condition and improve physical and chemical properties of carbon-based sorbents.
基金financially supported by the Chongqing Construction Project of Innovation Teams in Colleges and Universities-Petroleum Products Application Engineering and Technology(Project No.KJTD201342)the Chongqing Project of Innovation Research by Postgraduates(Project No.CYB16130)
文摘In order to investigate the influening factors of organic modification procedure and find out connections between organic modification and the properties of bentonite greases, organic montmorillonite(OMMT) thickeners with different surfactant dosages and constituents were synthesized through intercalation reaction between sodium montmorillonite(NaM MT) and quaternary ammonium surfactants in aqueous solvents. The lubricating greases were prepared with the resulting organoclays, while the penetration and oil separation of lubricating greases were evaluated, respectively. The surface modification process of montmorillonite(MMT) was analyzed and the thickening mechanism of OMMT was discussed in this study. The experimental results showed that, with an increasing amount of surfactant, the basal spacing between the clay platelets was increasing and the structure of modifier molecules layer in the interlayer was changing from lateral bilayer to paraffin-type bilayer. The optimal properties of lubricating greases were achieved, when the structure of surfactant molecules loaded in the interlayer was the paraffin-type monolayer, which meant that the dosage of modifier was equal to 120—140 mmol/(100g). Meanwhile, it was found that the thickening performance, colloid stability, anti-wear and friction-reducing performance of lubricating greases were improved, when the surfactants were mixed with octadecyl trimethyl ammonium chloride(OTAC) and hexadecyl trimethyl ammonium chloride(HTAC). And the optimum mole ratio of two surfactants is was 1:1.
文摘Dysprosium composite cobalt ferrite ionic magnetic fluids were prepared by precipitation in the presence of Tri-sodium citrate. Influence of dysprosium modification on magnetic property is studied. The result shows that magnetic response toward exterior magnetic field can be improved by adding Dy3+. Studies also show that the increase of reaction temperature may improve the modification effect of dysprosium. By adding dysprosium ions, the average diameter of the magnetic nanoparticles will be decreased evidently. It is clear that the particles appear as balls. Cobalt ferrite with sizes of 12-15 nm, rare earth composite cobalt ferrite with sizes of 6-8 nm.
基金supported by the National Natural Science Foundation of China (No. U 1507123)the Foundation from Qinghai Science and Technology Department (No. 2014-HZ-817)
文摘A calcium sulfate whisker （CSW） coated with glutaraldehyde crosslinked chitosan （GACS） was prepared to reinforce polyvinyl chloride （PVC） in this study. The results show that the optimum concentration of both chitosan （CS） and glutaraldehyde （GA） is 0.05 wt%. The tensile strength, impact strength, flexural modulus and vicat softening temperature of the PVC composite with 12 wt% of modified CSW are in- creased by 1 Z5%, 40.4%, 0.8% and 3.8% compared with those of the PVC composite with 12 wt~ of unmodified CSW, and by 2.9%, 42.4%, 2Z1% and 6.8% compared with those of pure PVC, respectively. The dynamic mechanical analysis results indicate that the modified CSW/PVC composite exhibits much higher storage modulus and glass transition temperature than those of unmodified CSW/PVC composite and pure PVC. In addition, the modified CSW/PVC composite also demonstrates good thermal properties with a high rapidest decomposition temperature （Trvd） and char residue. The scanning electron microscopy images of tensile-fractured surfaces show that the modified CSW has a strong interfacial adhesion with PVC matrix.
基金The Science and Technology Plan of Yunnan Science and Technology Department(No.2019FB077,202001AT070029)the Open Fund of Key Laboratory of Ministry of Education for Metallurgical Emission Reduction and Comprehensive Utilization of Resources(No.JKF19-08)the Industrialization Cultivation Project of Scientific Research Fund of Yunnan Provincial Department of Education(No.2016CYH07).
文摘To study the mechanism by which activated carbon is modified by HNO3 and Mn(NO3)2,the pore texture and surface chemical characteristics of carbon materials in coconut husk activated carbon(AC)were examined via scanning electron microscopy(SEM),Brunauer-Emmett-Teller(BET),X-ray diffraction(XRD),Fourier-transform infrared spectroscopy(FTIR),and X-ray photoelectron spectroscopy(XPS).After being modified by HNO3,the millipore character of AC became deformed,and the character of the adjacent pores remained consolidated.The surface manganites of Mn/AC-1 presented as block and reticular fiber structures,Mn/AC-2's surface manganites presented as petty mammock crystals,and Mn/AC-3's surface manganites were observed as gauze nanosheets that interlace to fill in the pore canal.Nitric acid modification was shown to enlarge surface pores but decrease the specific surface area of AC.Mn loading can be used to construct a new pore structure that,in turn,increased the total specific surface area as well as the specific surface area and the volume of the millipores.Mn/AC-2's pore structure was optimized at a calcination temperature of 500℃and a loading quantity of 5%.The ash content of AC was considerably reduced after modified by HNO3.The active materials for Mn/AC-1 mainly consisted of Mn3O4,with a few Mn2O3 crystals,whereas Mn/AC-2's materials were mainly Mn3O4 and some MnO crystals.Mn/AC-3 was exclusively composed of Mn3O4.HNO3 activation and Mn loading modification did not considerably affect the functional group species present on the catalyst.Modification conditions using the same loading quantities and higher calcination temperatures decreased the number of O—H and N—H bonds while conversely increasing the number of CC and C—O bonds.On the contrary,the use of a higher loading quantity while maintaining the same calcination temperature increased the number of O—H and N—H bonds.A higher loading quantity is beneficial for increasing Mn^4+species.A higher calcination temperature is beneficial for increasing Mn^3+species.The results can optimize the conditions under which Mn/AC catalyst modification occurs,thus improving the physical and chemical properties of carbon-based sorbents.
