The temperature effects on the electrical performance of a large area multicrystalline silicon solar cell with back-contact technology have been studied in a desert area under ambient conditions using the current shun...The temperature effects on the electrical performance of a large area multicrystalline silicon solar cell with back-contact technology have been studied in a desert area under ambient conditions using the current shunt measuring technique. Therefore, most of the problems encountered with traditional measuring techniques are avoided. The temperature dependency of the current shunt from 5oC up to 50oC has been investigated. Its temperature coefficient proves to be negligible which means that the temperature dependency of the solar cell is completely independent of the current shunt. The solar module installed in a tilted position at the optimum angle of the location, has been tested in two different seasons (winter and summer). The obtained solar cell short circuit current, open circuit voltage and output power are correlated with the measured incident radiation in both seasons and all results are discussed.展开更多
The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its ...The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its definition associated closely with the surface area per unit volume, Sv, of grain. The focus of the measuring principles of the characteristic grain size is put on determining Sv of grains. Unlike the measurement of average grain size commonly used, G, correcting factors such as grain shape and grain size distribution factors, will not be applied to the determination of the characteristic grain size, Gc, due to its unique geometric meaning and the measure precision of Sv being guaranteed by quantitative stereological technique and gas adsorption method. The measurement of Gc can be directly carried out on the polished and etched cross section of materials, similar to the measuremernt of the average grain size using the Heyn intercept method.展开更多
Satellite-based precipitation products have been widely used to estimate precipitation, especially over regions with sparse rain gauge networks. However, the low spatial resolution of these products has limited their ...Satellite-based precipitation products have been widely used to estimate precipitation, especially over regions with sparse rain gauge networks. However, the low spatial resolution of these products has limited their application in localized regions and watersheds.This study investigated a spatial downscaling approach, Geographically Weighted Regression Kriging(GWRK), to downscale the Tropical Rainfall Measuring Mission(TRMM) 3 B43 Version 7 over the Lancang River Basin(LRB) for 2001–2015. Downscaling was performed based on the relationships between the TRMM precipitation and the Normalized Difference Vegetation Index(NDVI), the Land Surface Temperature(LST), and the Digital Elevation Model(DEM). Geographical ratio analysis(GRA) was used to calibrate the annual downscaled precipitation data, and the monthly fractions derived from the original TRMM data were used to disaggregate annual downscaled and calibrated precipitation to monthly precipitation at 1 km resolution. The final downscaled precipitation datasets were validated against station-based observed precipitation in 2001–2015. Results showed that: 1) The TRMM 3 B43 precipitation was highly accurate with slight overestimation at the basin scale(i.e., CC(correlation coefficient) = 0.91, Bias = 13.3%). Spatially, the accuracies of the upstream and downstream regions were higher than that of the midstream region. 2) The annual downscaled TRMM precipitation data at 1 km spatial resolution obtained by GWRK effectively captured the high spatial variability of precipitation over the LRB. 3) The annual downscaled TRMM precipitation with GRA calibration gave better accuracy compared with the original TRMM dataset. 4) The final downscaled and calibrated precipitation had significantly improved spatial resolution, and agreed well with data from the validated rain gauge stations, i.e., CC = 0.75, RMSE(root mean square error) = 182 mm, MAE(mean absolute error) = 142 mm, and Bias = 0.78%for annual precipitation and CC = 0.95, RMSE = 25 mm, MAE = 16 mm, and Bias = 0.67% for monthly precipitation.展开更多
The practical value of high-precision models of the studied physical phenomena and technological processes is a decisive factor in science and technology. Currently, numerous methods and criteria for optimizing models...The practical value of high-precision models of the studied physical phenomena and technological processes is a decisive factor in science and technology. Currently, numerous methods and criteria for optimizing models have been proposed. However, the classification of measurement uncertainties due to the number of variables taken into account and their qualitative choice is still not given sufficient attention. The goal is to develop a new criterion suitable for any groups of experimental data obtained as a result of applying various measurement methods. Using the “information-theoretic method”, we propose two procedures for analyzing experimental results using a quantitative indicator to calculate the relative uncertainty of the measurement model, which, in turn, determines the legitimacy of the declared value of a physical constant. The presented procedure is used to analyze the results of measurements of the Boltzmann constant, Planck constant, Hubble constant and gravitational constant.展开更多
This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of con...This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.展开更多
The aim of this work is mathematical education through the knowledge system and mathematical modeling. A net model of formation of mathematical knowledge as a deductive theory is suggested here. Within this model the ...The aim of this work is mathematical education through the knowledge system and mathematical modeling. A net model of formation of mathematical knowledge as a deductive theory is suggested here. Within this model the formation of deductive theory is represented as the development of a certain informational space, the elements of which are structured in the form of the orientated semantic net. This net is properly metrized and characterized by a certain system of coverings. It allows injecting net optimization parameters, regulating qualitative aspects of knowledge system under consideration. To regulate the creative processes of the formation and realization of mathematical know- edge, stochastic model of formation deductive theory is suggested here in the form of branching Markovian process, which is realized in the corresponding informational space as a semantic net. According to this stochastic model we can get correct foundation of criterion of optimization creative processes that leads to “great main points” strategy (GMP-strategy) in the process of realization of the effective control in the research work in the sphere of mathematics and its applications.展开更多
Cowpea (Vigna unguiculata (L.) Walp), a legume crop that is grown in the worldwide, provides beneficial proteins for human consumption and animal feeding. In comparison, Rapid N analyzer as traditional method, has bee...Cowpea (Vigna unguiculata (L.) Walp), a legume crop that is grown in the worldwide, provides beneficial proteins for human consumption and animal feeding. In comparison, Rapid N analyzer as traditional method, has been widely used to measure protein content through the percentage of total nitrogen in the seed’s grounded powder. Near-Infrared Reflectance (NIR) has commonly been used to measure protein content in soybean seeds using whole grain without the need of seed grinding, which makes it possible to obtain fast results at a lower cost-per-analysis than the traditional combustion method. The specific objective of this study is to test a rapid method for measuring cowpea seed protein content by the NIR analyzer comparing to the traditional rapid N analyzer. A total of 240 cowpea genotypes were used in this study, including six seed coat colors, black, blackeye, browneye, cream, pinkeye, and red with 40 cowpea genotypes. The results showed that a linear relationship exists between the NIR analyzer and the Rapid N analyzer in the six different color groups. The correlation efficiency (r) between the seed protein contents from NIR and Rapid N was higher for pinkeye seed (r = 0.867), blackeye (0.771), cream (0.729), browneye (0.700), and red (0.623), respectively, but lower for black seeds, indicating that the NIR analyzer can be used to measure protein content for cowpea seeds with the five types of seed coat except black. Overview, the cowpea seed protein content measured from the NIR analyzer showed a little higher seed protein content. A series of regression models with different seed coat color have been built to adjust to protein content of colorful cowpea seeds from the NIR analyzer. But, it is not recommended to use for black color seeds due to a very low correlation efficiency (r) value with 0.184.展开更多
Live line measurement methods can reduce the loss of power outages and eliminate interference. There are three live line measurement methods including integral method, differential method and algebraic method. A simul...Live line measurement methods can reduce the loss of power outages and eliminate interference. There are three live line measurement methods including integral method, differential method and algebraic method. A simulation model of?two coupled parallel transmission lines spanning on the same towers is built in PSCAD and the calculation errors of these three methods are compared with different sampling frequencies by using of Matlab. The effect of harmonic on calculation is also involved. The simulation results indicate that harmonic has the least effect on the algebraic method which provides stable result and small error.展开更多
Copper Zinc Antimony Sulfide(CZAS)is derived from Copper Antimony Sulfide(CAS),a famatinite class of compound.In the current paper,the first step for using Copper,Zinc,Antimony and Sulfide as materials in manufacturin...Copper Zinc Antimony Sulfide(CZAS)is derived from Copper Antimony Sulfide(CAS),a famatinite class of compound.In the current paper,the first step for using Copper,Zinc,Antimony and Sulfide as materials in manufacturing synchrotronic biosensor-namely increasing the sensitivity of biosensor through creating Copper Zinc Antimony Sulfide,CZAS(Cu1.18Zn0.40Sb1.90S7.2)semiconductor and using it instead of Copper Tin Sulfide,CTS(Cu2SnS3)for tracking,monitoring,imaging,measuring,diagnosing and detecting cancer cells,is evaluated.Further,optimization of tris(2,2'-bipyridyl)ruthenium(II)(Ru(bpy)32+)concentrations and Copper Zinc Antimony Sulfide,CZAS(Cu1.18Zn0.40Sb1.90S7.2)semiconductor as two main and effective materials in the intensity of synchrotron for tracking,monitoring,imaging,measuring,diagnosing and detecting cancer cells are considered so that the highest sensitivity obtains.In this regard,various concentrations of two materials were prepared and photon emission was investigated in the absence of cancer cells.On the other hand,ccancer diagnosis requires the analysis of images and attributes as well as collecting many clinical and mammography variables.In diagnosis of cancer,it is important to determine whether a tumor is benign or malignant.The information about cancer risk prediction along with the type of tumor are crucial for patients and effective medical decision making.An ideal diagnostic system could effectively distinguish between benign and malignant cells;however,such a system has not been created yet.In this study,a model is developed to improve the prediction probability of cancer.It is necessary to have such a prediction model as the survival probability of cancer is high when patients are diagnosed at early stages.展开更多
By using correlation-detection technique and improving structure of the test tube,the background noise of thermionic-electrons and space charge effect are restrained.The sec-ondary emission coefficient δ of thermioni...By using correlation-detection technique and improving structure of the test tube,the background noise of thermionic-electrons and space charge effect are restrained.The sec-ondary emission coefficient δ of thermionic cathode at high temperature has been studied.Theδ of impregnated scandate cathodes increases exponentially with increasing temperature at lowenergy and current of the bombardment electrons;at high energy or current of the bombardmentelectrons the temperature has little effect on δ.The research shows that an enhanced thermionicemission occurred when the cathode works at high temperature and under electron bombardment.These phenomena are discussed in terms of “internal field model”.展开更多
Selecting the optimal machining parameters for impeller surface is a challenging task in the automatic manufacturing industry, due to its free-form surface and deep-crooked flow channel.Existing experimental methods r...Selecting the optimal machining parameters for impeller surface is a challenging task in the automatic manufacturing industry, due to its free-form surface and deep-crooked flow channel.Existing experimental methods require lots of machining experiments and off-line tests, which may lead to high machining cost and low efficiency. This paper proposes a novel method of machining parameters optimization for an impeller based on the on-machine measuring technique. The absolute average error and standard deviation of the measured points are used to define the grey relational grade for reconstructing the objective function, and the complex problem of multi-objective optimization is simplified into a problem of single-objective optimization. Then, by comparing the values of the defined grey relational grade in a designed orthogonal experiment, the optimal combination of the machining parameters is obtained. The experiment-solving process of the objective function corresponds to the minimization of the used errors, which is advantageous to reducing the machining error. The proposed method is efficient and low-cost, since it does not require re-clamping the workpiece for off-line tests. Its effectiveness is verified by an on-machine inspection experiment of the impeller blade.展开更多
Rehabilitation devices help to recover the physical abilities of patients. This study aims to develop a portable rehabilitation device that is safe to use when?patients are holding it by hands. In a previous study, to...Rehabilitation devices help to recover the physical abilities of patients. This study aims to develop a portable rehabilitation device that is safe to use when?patients are holding it by hands. In a previous study, to realize a home rehabilitation device, a flexible spherical actuator that can provide motion to patients was developed. In this study, to measure the relative position between both handling stages, a 3D coordinate measuring device using three wire-type linear potentiometers and an embedded controller was proposed and tested. In this paper, the spherical actuator with built-in 3D coordinate measuring device is described. The measuring method and experimental results obtained are also presented. The tracking position control of the actuator using the measuring device was carried out. As a result, the position of the handling stages can be successfully controlled using the feedback signal from the tested?measuring device.展开更多
Rapid technological advancements drive miniaturization and high energy density in devices,thereby increasing nanoscale thermal management demands and urging development of higher spatial resolution technologies for th...Rapid technological advancements drive miniaturization and high energy density in devices,thereby increasing nanoscale thermal management demands and urging development of higher spatial resolution technologies for thermal imaging and transport research.Here,we introduce an approach to measure nanoscale thermal resistance using in situ inelastic scanning transmission electron microscopy.By constructing unidirectional heating flux with controlled temperature gradients and analyzing electron energy-loss/gain signals under optimized acquisition conditions,nanometer-resolution in mapping phonon apparent temperature is achieved.Thus,interfacial thermal resistance is determined by calculating the ratio of interfacial temperature difference to bulk temperature gradient.This methodology enables direct measurement of thermal transport properties for atomic-scale structural features(e.g.,defects and heterointerfaces),resolving critical structure-performance relationships,providing a useful tool for investigating thermal phenomena at the(sub-)nanoscale.展开更多
A lower bound to errors of measuring object position is constructed as a function of parameters of a monocular computer vision system (CVS) as well as of observation conditions and a shape of an observed marker. This ...A lower bound to errors of measuring object position is constructed as a function of parameters of a monocular computer vision system (CVS) as well as of observation conditions and a shape of an observed marker. This bound justifies the specification of the CVS parameters and allows us to formulate constraints for an object trajectory based on required measurement accuracy. For making the measurement, the boundaries of marker image are used.展开更多
By using principal component analysis,this paper had modified and put forward a theoretical model of evaluation on tourist satisfaction degree with tourist perception quality and tourist satisfaction degree as structu...By using principal component analysis,this paper had modified and put forward a theoretical model of evaluation on tourist satisfaction degree with tourist perception quality and tourist satisfaction degree as structure variables and with thirty indexes like image of tourist area,tourists' expectation,infrastructure in tourist area,landscape features and ticket price as observed variables,based on random questionnaire survey of tourists of Zhenyuan ancient city in Guizhou Province and the existing evaluation models of tourist satisfaction degree at home and abroad.The survey result showed that tourist satisfaction degree was not high,that tourists were dissatisfied with observing facilities,transportation,accommodation and landscape features,and that the attraction power of tourist area was weak.The comprehensive tourist satisfaction degree of Zhenyuan ancient city was 77.653.Therefore,the government should enhance reconstruction of infrastructure and construction of landscape features,and improve tourist service quality level,so as to realize sustainable development of tourist economy in Zhenyuan ancient city.展开更多
Improving and sustaining successful public health interventions relies increasingly on the ability to identify the key components of an intervention that are effective, to identify for whom the intervention is effecti...Improving and sustaining successful public health interventions relies increasingly on the ability to identify the key components of an intervention that are effective, to identify for whom the intervention is effective, and to identify under what conditions the intervention is effective. Bayesian probability an “advanced” experimental design framework of methodology is used in the study to develop a systematic tool that can assist health care managers and field workers in measuring effectiveness of health program intervention and systematically assess the components of programs to be applied to design program improvements and to advocate for resources. The study focuses on essential management elements of the health system that must be in place to ensure the effectiveness of IMNCI intervention. Early experiences with IMNCI implemented led to greater awareness of the need to improve drug delivery, support for effective planning and management at all levels and address issues related to the organization of work at health facilities. The efficacy of IMNCI program from the experience of experts and specialists working in the state is 0.67 and probability of effective- ness of all management components in the study is 58%. Overall the standard assessment tool used predicts success of around 39% for the IMNCI intervention implemented in current situation in Rajasthan. Training management component carried the highest weight-age of 21% with 73% probability of being effective in the state. Human resource management has weight-age of 13% with 53% probability of being effective in current scenario. Monitoring and evaluation carried a weight-age of 11% with only 33% probability of being effective. Operational planning carried a weight-age of 9% with 100% probability of being effectively managed. Supply management carried a weight-age of 8% with zero probability of being effective in the current field scenario. In the study, each question that received low score identifies it as a likely obstacle to the success of the health program. The health program should improve all sub-components with low scores to increase the likelihood of meeting its objectives. Public health interventions tend to be complex, programmatic and context dependent. The evaluation of evidence must distinguish between the fidelity of the evaluation process in detecting the success or failure of the intervention, and relative success or failure of the intervention itself. We advocate management attributes incorporation into criteria for appraising evidence on public health interventions. This can strengthen the value of evidence and their potential contributions to the process of public health management and social development.展开更多
A live line measurement method for the zero sequence parameters of transmission lines with mutual inductance is introduced. The mathematical models of the measurement method are given. Global Positioning System (GPS) ...A live line measurement method for the zero sequence parameters of transmission lines with mutual inductance is introduced. The mathematical models of the measurement method are given. Global Positioning System (GPS) is used as the synchronous signal for the measurement carried out at different substations simultaneously. The measurement system and digital simulation results are given. Finally, the live line measurement results of two 220 kV transmission lines with mutual inductance in Hainangrid are given. Results from both simulation and on-site measurement show that the live line measurement method is feasible, and its measurement accuracy can satisfactorily meet the requirements of engineering measurement.展开更多
Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= ...Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= 1010～ 1012Ω) in order to measuring the plant weak signals and ensuring high common mode rejection ratio (CMRR). And wavelet transform was applied in denoising based on cross-validation (CV)threshold value. the experiment showed that this system could effectively detect the change of plant potentials,four-week old cucumber was stimulated by heat wounding, the variation potential (VP) and action potential(AP) would be evoked, the AP's varying amplitude can reach 40mV; the AP changed very fast, its duration time is about 0.01～0.02s and its amplitude often change from 15μV～5mV.展开更多
文摘The temperature effects on the electrical performance of a large area multicrystalline silicon solar cell with back-contact technology have been studied in a desert area under ambient conditions using the current shunt measuring technique. Therefore, most of the problems encountered with traditional measuring techniques are avoided. The temperature dependency of the current shunt from 5oC up to 50oC has been investigated. Its temperature coefficient proves to be negligible which means that the temperature dependency of the solar cell is completely independent of the current shunt. The solar module installed in a tilted position at the optimum angle of the location, has been tested in two different seasons (winter and summer). The obtained solar cell short circuit current, open circuit voltage and output power are correlated with the measured incident radiation in both seasons and all results are discussed.
文摘The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its definition associated closely with the surface area per unit volume, Sv, of grain. The focus of the measuring principles of the characteristic grain size is put on determining Sv of grains. Unlike the measurement of average grain size commonly used, G, correcting factors such as grain shape and grain size distribution factors, will not be applied to the determination of the characteristic grain size, Gc, due to its unique geometric meaning and the measure precision of Sv being guaranteed by quantitative stereological technique and gas adsorption method. The measurement of Gc can be directly carried out on the polished and etched cross section of materials, similar to the measuremernt of the average grain size using the Heyn intercept method.
基金Under the auspices of the National Natural Science Foundation of China(No.41661099)the National Key Research and Development Program of China(No.Grant 2016YFA0601601)
文摘Satellite-based precipitation products have been widely used to estimate precipitation, especially over regions with sparse rain gauge networks. However, the low spatial resolution of these products has limited their application in localized regions and watersheds.This study investigated a spatial downscaling approach, Geographically Weighted Regression Kriging(GWRK), to downscale the Tropical Rainfall Measuring Mission(TRMM) 3 B43 Version 7 over the Lancang River Basin(LRB) for 2001–2015. Downscaling was performed based on the relationships between the TRMM precipitation and the Normalized Difference Vegetation Index(NDVI), the Land Surface Temperature(LST), and the Digital Elevation Model(DEM). Geographical ratio analysis(GRA) was used to calibrate the annual downscaled precipitation data, and the monthly fractions derived from the original TRMM data were used to disaggregate annual downscaled and calibrated precipitation to monthly precipitation at 1 km resolution. The final downscaled precipitation datasets were validated against station-based observed precipitation in 2001–2015. Results showed that: 1) The TRMM 3 B43 precipitation was highly accurate with slight overestimation at the basin scale(i.e., CC(correlation coefficient) = 0.91, Bias = 13.3%). Spatially, the accuracies of the upstream and downstream regions were higher than that of the midstream region. 2) The annual downscaled TRMM precipitation data at 1 km spatial resolution obtained by GWRK effectively captured the high spatial variability of precipitation over the LRB. 3) The annual downscaled TRMM precipitation with GRA calibration gave better accuracy compared with the original TRMM dataset. 4) The final downscaled and calibrated precipitation had significantly improved spatial resolution, and agreed well with data from the validated rain gauge stations, i.e., CC = 0.75, RMSE(root mean square error) = 182 mm, MAE(mean absolute error) = 142 mm, and Bias = 0.78%for annual precipitation and CC = 0.95, RMSE = 25 mm, MAE = 16 mm, and Bias = 0.67% for monthly precipitation.
文摘The practical value of high-precision models of the studied physical phenomena and technological processes is a decisive factor in science and technology. Currently, numerous methods and criteria for optimizing models have been proposed. However, the classification of measurement uncertainties due to the number of variables taken into account and their qualitative choice is still not given sufficient attention. The goal is to develop a new criterion suitable for any groups of experimental data obtained as a result of applying various measurement methods. Using the “information-theoretic method”, we propose two procedures for analyzing experimental results using a quantitative indicator to calculate the relative uncertainty of the measurement model, which, in turn, determines the legitimacy of the declared value of a physical constant. The presented procedure is used to analyze the results of measurements of the Boltzmann constant, Planck constant, Hubble constant and gravitational constant.
文摘This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.
文摘The aim of this work is mathematical education through the knowledge system and mathematical modeling. A net model of formation of mathematical knowledge as a deductive theory is suggested here. Within this model the formation of deductive theory is represented as the development of a certain informational space, the elements of which are structured in the form of the orientated semantic net. This net is properly metrized and characterized by a certain system of coverings. It allows injecting net optimization parameters, regulating qualitative aspects of knowledge system under consideration. To regulate the creative processes of the formation and realization of mathematical know- edge, stochastic model of formation deductive theory is suggested here in the form of branching Markovian process, which is realized in the corresponding informational space as a semantic net. According to this stochastic model we can get correct foundation of criterion of optimization creative processes that leads to “great main points” strategy (GMP-strategy) in the process of realization of the effective control in the research work in the sphere of mathematics and its applications.
文摘Cowpea (Vigna unguiculata (L.) Walp), a legume crop that is grown in the worldwide, provides beneficial proteins for human consumption and animal feeding. In comparison, Rapid N analyzer as traditional method, has been widely used to measure protein content through the percentage of total nitrogen in the seed’s grounded powder. Near-Infrared Reflectance (NIR) has commonly been used to measure protein content in soybean seeds using whole grain without the need of seed grinding, which makes it possible to obtain fast results at a lower cost-per-analysis than the traditional combustion method. The specific objective of this study is to test a rapid method for measuring cowpea seed protein content by the NIR analyzer comparing to the traditional rapid N analyzer. A total of 240 cowpea genotypes were used in this study, including six seed coat colors, black, blackeye, browneye, cream, pinkeye, and red with 40 cowpea genotypes. The results showed that a linear relationship exists between the NIR analyzer and the Rapid N analyzer in the six different color groups. The correlation efficiency (r) between the seed protein contents from NIR and Rapid N was higher for pinkeye seed (r = 0.867), blackeye (0.771), cream (0.729), browneye (0.700), and red (0.623), respectively, but lower for black seeds, indicating that the NIR analyzer can be used to measure protein content for cowpea seeds with the five types of seed coat except black. Overview, the cowpea seed protein content measured from the NIR analyzer showed a little higher seed protein content. A series of regression models with different seed coat color have been built to adjust to protein content of colorful cowpea seeds from the NIR analyzer. But, it is not recommended to use for black color seeds due to a very low correlation efficiency (r) value with 0.184.
文摘Live line measurement methods can reduce the loss of power outages and eliminate interference. There are three live line measurement methods including integral method, differential method and algebraic method. A simulation model of?two coupled parallel transmission lines spanning on the same towers is built in PSCAD and the calculation errors of these three methods are compared with different sampling frequencies by using of Matlab. The effect of harmonic on calculation is also involved. The simulation results indicate that harmonic has the least effect on the algebraic method which provides stable result and small error.
文摘Copper Zinc Antimony Sulfide(CZAS)is derived from Copper Antimony Sulfide(CAS),a famatinite class of compound.In the current paper,the first step for using Copper,Zinc,Antimony and Sulfide as materials in manufacturing synchrotronic biosensor-namely increasing the sensitivity of biosensor through creating Copper Zinc Antimony Sulfide,CZAS(Cu1.18Zn0.40Sb1.90S7.2)semiconductor and using it instead of Copper Tin Sulfide,CTS(Cu2SnS3)for tracking,monitoring,imaging,measuring,diagnosing and detecting cancer cells,is evaluated.Further,optimization of tris(2,2'-bipyridyl)ruthenium(II)(Ru(bpy)32+)concentrations and Copper Zinc Antimony Sulfide,CZAS(Cu1.18Zn0.40Sb1.90S7.2)semiconductor as two main and effective materials in the intensity of synchrotron for tracking,monitoring,imaging,measuring,diagnosing and detecting cancer cells are considered so that the highest sensitivity obtains.In this regard,various concentrations of two materials were prepared and photon emission was investigated in the absence of cancer cells.On the other hand,ccancer diagnosis requires the analysis of images and attributes as well as collecting many clinical and mammography variables.In diagnosis of cancer,it is important to determine whether a tumor is benign or malignant.The information about cancer risk prediction along with the type of tumor are crucial for patients and effective medical decision making.An ideal diagnostic system could effectively distinguish between benign and malignant cells;however,such a system has not been created yet.In this study,a model is developed to improve the prediction probability of cancer.It is necessary to have such a prediction model as the survival probability of cancer is high when patients are diagnosed at early stages.
文摘By using correlation-detection technique and improving structure of the test tube,the background noise of thermionic-electrons and space charge effect are restrained.The sec-ondary emission coefficient δ of thermionic cathode at high temperature has been studied.Theδ of impregnated scandate cathodes increases exponentially with increasing temperature at lowenergy and current of the bombardment electrons;at high energy or current of the bombardmentelectrons the temperature has little effect on δ.The research shows that an enhanced thermionicemission occurred when the cathode works at high temperature and under electron bombardment.These phenomena are discussed in terms of “internal field model”.
基金co-supported by the National Basic Research Program of China(No.2015CB057304)the National Natural Science Foundation of China(Nos.51535004 and91648111)
文摘Selecting the optimal machining parameters for impeller surface is a challenging task in the automatic manufacturing industry, due to its free-form surface and deep-crooked flow channel.Existing experimental methods require lots of machining experiments and off-line tests, which may lead to high machining cost and low efficiency. This paper proposes a novel method of machining parameters optimization for an impeller based on the on-machine measuring technique. The absolute average error and standard deviation of the measured points are used to define the grey relational grade for reconstructing the objective function, and the complex problem of multi-objective optimization is simplified into a problem of single-objective optimization. Then, by comparing the values of the defined grey relational grade in a designed orthogonal experiment, the optimal combination of the machining parameters is obtained. The experiment-solving process of the objective function corresponds to the minimization of the used errors, which is advantageous to reducing the machining error. The proposed method is efficient and low-cost, since it does not require re-clamping the workpiece for off-line tests. Its effectiveness is verified by an on-machine inspection experiment of the impeller blade.
文摘Rehabilitation devices help to recover the physical abilities of patients. This study aims to develop a portable rehabilitation device that is safe to use when?patients are holding it by hands. In a previous study, to realize a home rehabilitation device, a flexible spherical actuator that can provide motion to patients was developed. In this study, to measure the relative position between both handling stages, a 3D coordinate measuring device using three wire-type linear potentiometers and an embedded controller was proposed and tested. In this paper, the spherical actuator with built-in 3D coordinate measuring device is described. The measuring method and experimental results obtained are also presented. The tracking position control of the actuator using the measuring device was carried out. As a result, the position of the handling stages can be successfully controlled using the feedback signal from the tested?measuring device.
基金supported by the National Natural Science Foundation of China(Grant No.52125307)the National Key R&D Program of China(Grant No.2021YFB3501500)the support from the New Cornerstone Science Foundation through the XPLORER PRIZE。
文摘Rapid technological advancements drive miniaturization and high energy density in devices,thereby increasing nanoscale thermal management demands and urging development of higher spatial resolution technologies for thermal imaging and transport research.Here,we introduce an approach to measure nanoscale thermal resistance using in situ inelastic scanning transmission electron microscopy.By constructing unidirectional heating flux with controlled temperature gradients and analyzing electron energy-loss/gain signals under optimized acquisition conditions,nanometer-resolution in mapping phonon apparent temperature is achieved.Thus,interfacial thermal resistance is determined by calculating the ratio of interfacial temperature difference to bulk temperature gradient.This methodology enables direct measurement of thermal transport properties for atomic-scale structural features(e.g.,defects and heterointerfaces),resolving critical structure-performance relationships,providing a useful tool for investigating thermal phenomena at the(sub-)nanoscale.
文摘A lower bound to errors of measuring object position is constructed as a function of parameters of a monocular computer vision system (CVS) as well as of observation conditions and a shape of an observed marker. This bound justifies the specification of the CVS parameters and allows us to formulate constraints for an object trajectory based on required measurement accuracy. For making the measurement, the boundaries of marker image are used.
基金Supported by Planning Project of Kaili Institute(Z1009)and Youth Foundation of Special Scientific Research Project of Key Discipline of Tourist Management of Kaili Institute(lgz200904)~~
文摘By using principal component analysis,this paper had modified and put forward a theoretical model of evaluation on tourist satisfaction degree with tourist perception quality and tourist satisfaction degree as structure variables and with thirty indexes like image of tourist area,tourists' expectation,infrastructure in tourist area,landscape features and ticket price as observed variables,based on random questionnaire survey of tourists of Zhenyuan ancient city in Guizhou Province and the existing evaluation models of tourist satisfaction degree at home and abroad.The survey result showed that tourist satisfaction degree was not high,that tourists were dissatisfied with observing facilities,transportation,accommodation and landscape features,and that the attraction power of tourist area was weak.The comprehensive tourist satisfaction degree of Zhenyuan ancient city was 77.653.Therefore,the government should enhance reconstruction of infrastructure and construction of landscape features,and improve tourist service quality level,so as to realize sustainable development of tourist economy in Zhenyuan ancient city.
文摘Improving and sustaining successful public health interventions relies increasingly on the ability to identify the key components of an intervention that are effective, to identify for whom the intervention is effective, and to identify under what conditions the intervention is effective. Bayesian probability an “advanced” experimental design framework of methodology is used in the study to develop a systematic tool that can assist health care managers and field workers in measuring effectiveness of health program intervention and systematically assess the components of programs to be applied to design program improvements and to advocate for resources. The study focuses on essential management elements of the health system that must be in place to ensure the effectiveness of IMNCI intervention. Early experiences with IMNCI implemented led to greater awareness of the need to improve drug delivery, support for effective planning and management at all levels and address issues related to the organization of work at health facilities. The efficacy of IMNCI program from the experience of experts and specialists working in the state is 0.67 and probability of effective- ness of all management components in the study is 58%. Overall the standard assessment tool used predicts success of around 39% for the IMNCI intervention implemented in current situation in Rajasthan. Training management component carried the highest weight-age of 21% with 73% probability of being effective in the state. Human resource management has weight-age of 13% with 53% probability of being effective in current scenario. Monitoring and evaluation carried a weight-age of 11% with only 33% probability of being effective. Operational planning carried a weight-age of 9% with 100% probability of being effectively managed. Supply management carried a weight-age of 8% with zero probability of being effective in the current field scenario. In the study, each question that received low score identifies it as a likely obstacle to the success of the health program. The health program should improve all sub-components with low scores to increase the likelihood of meeting its objectives. Public health interventions tend to be complex, programmatic and context dependent. The evaluation of evidence must distinguish between the fidelity of the evaluation process in detecting the success or failure of the intervention, and relative success or failure of the intervention itself. We advocate management attributes incorporation into criteria for appraising evidence on public health interventions. This can strengthen the value of evidence and their potential contributions to the process of public health management and social development.
文摘A live line measurement method for the zero sequence parameters of transmission lines with mutual inductance is introduced. The mathematical models of the measurement method are given. Global Positioning System (GPS) is used as the synchronous signal for the measurement carried out at different substations simultaneously. The measurement system and digital simulation results are given. Finally, the live line measurement results of two 220 kV transmission lines with mutual inductance in Hainangrid are given. Results from both simulation and on-site measurement show that the live line measurement method is feasible, and its measurement accuracy can satisfactorily meet the requirements of engineering measurement.
文摘Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= 1010～ 1012Ω) in order to measuring the plant weak signals and ensuring high common mode rejection ratio (CMRR). And wavelet transform was applied in denoising based on cross-validation (CV)threshold value. the experiment showed that this system could effectively detect the change of plant potentials,four-week old cucumber was stimulated by heat wounding, the variation potential (VP) and action potential(AP) would be evoked, the AP's varying amplitude can reach 40mV; the AP changed very fast, its duration time is about 0.01～0.02s and its amplitude often change from 15μV～5mV.
