This paper addresses a master-slave synchro- nization strategy for complex dynamic systems based on feedback control. This strategy is applied to 3-DOF pla- nar manipulators in order to obtain synchronization in such ...This paper addresses a master-slave synchro- nization strategy for complex dynamic systems based on feedback control. This strategy is applied to 3-DOF pla- nar manipulators in order to obtain synchronization in such complicated as chaotic motions of end-effectors. A chaotic curve is selected from Duffing equation as the trajectory of master end-effector and a piecewise approximation method is proposed to accurately represent this chaotic trajectory of end-effectors. The dynamical equations of master-slave manipulators with synchronization controller are derived, and the Lyapunov stability theory is used to determine the stability of this controlled synchronization system. In numer- ical experiments, the synchronous motions of end-effectors as well as three joint angles and torques of master-slave manipulators are studied under the control of the proposed synchronization strategy. It is found that the positive gain matrix affects the implementation of synchronization con- trol strategy. This synchronization control strategy proves the synchronization＇s feasibility and controllability for com- plicated motions generated by master-slave manipulators.展开更多
In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardwar...In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.展开更多
Aiming at the weaknesses of LON bus, combining the coexistence of fieldbus and DCS (Distribu ted Control Systems) in control networks, the authors introduce a hierarchical hybrid control network design based on LON an...Aiming at the weaknesses of LON bus, combining the coexistence of fieldbus and DCS (Distribu ted Control Systems) in control networks, the authors introduce a hierarchical hybrid control network design based on LON and master slave RS 422/485 protocol. This design adopts LON as the trunk, master slave RS 422/485 control networks are connected to LON as special subnets by dedicated gateways. It is an implementation method for isomerous control network integration. Data management is ranked according to real time requirements for different network data. The core components, such as control network nodes, router and gateway, are detailed in the paper. The design utilizes both communication advantage of LonWorks technology and the more powerful control ability of universal MCUs or PLCs, thus it greatly increases system response speed and performance cost ratio.展开更多
Master robots are integral components of teleoperated robot-assisted minimally invasive surgery systems.Among them,parallel mechanism-based 6-degree-of-freedom master robots are distinguished by low inertia and high-f...Master robots are integral components of teleoperated robot-assisted minimally invasive surgery systems.Among them,parallel mechanism-based 6-degree-of-freedom master robots are distinguished by low inertia and high-force feedback.However,complex kinematics and singularities are the main barriers limiting its usage.This study converts the Hexa-type 6-RUS mechanism into a master robot to construct master-slave teleoperation system.The clinical background is briefly introduced and a representative surgical robot is employed to analyze the master-slave mapping relationship.The inverse/forward kinematics,the Jacobian matrix,and the translation and orientation workspace are derived as the bases of master robot’s application.The architecture parameters are optimized by the global transmission index to achieve better motion/force transmissibility.Based on the optimal result,the prototype and the master-slave control loop are constructed.Finally,the corresponding master-slave teleoperation experiment and model experiment demonstrate that the proposed master robot satisfies the basic need for medical application.展开更多
Content Addressable Memory (CAM) is a type of memory used for high-speed search applications. Due to parallel comparison feature, the CAM memory leads to large power consumption which is caused by frequent pre-charge ...Content Addressable Memory (CAM) is a type of memory used for high-speed search applications. Due to parallel comparison feature, the CAM memory leads to large power consumption which is caused by frequent pre-charge or discharge of match line. In this paper, CAM for automatic charge balancing with self-control mechanism is proposed to control the voltage swing of ML for reducing the power consumption of CAM. Another technique to reduce the power dissipation is to use MSML, it combines the master-slave architecture with charge minimization technique. Unlike the conventional design, only one match line (ML) is used, whereas in Master-Slave Match Line (MSML) one master ML and several slave MLs are used to reduce the power dissipation in CAM caused by match lines (MLs). Theoretically, the match line (ML) reduces the power consumption up to 50% which is independent of search and match case. The simulation results using Cadence tool of MSML show the reduced power consumption in CAM and modified CAM cell.展开更多
The networked synchronization problem of a class of master-slave chaotic systems with time-varying communication topologies is investigated in this paper. Based on algebraic graph theory and matrix theory, a simple li...The networked synchronization problem of a class of master-slave chaotic systems with time-varying communication topologies is investigated in this paper. Based on algebraic graph theory and matrix theory, a simple linear state feedback controller is designed to synchronize the master chaotic system and the slave chaotic systems with a time- varying communication topology connection. The exponential stability of the closed-loop networked synchronization error system is guaranteed by applying Lyapunov stability theory. The derived novel criteria are in the form of linear matrix inequalities （LMIs）, which are easy to examine and tremendously reduce the computation burden from the feedback matrices. This paper provides an alternative networked secure communication scheme which can be extended conveniently. An illustrative example is given to demonstrate the effectiveness of the proposed networked synchronization method.展开更多
In order to make the manipulators useful, some force feedback is required to enable the operator to sense the robot’s feelings. Without force feedback, many tasks will not be able to be carried out. For these reasons...In order to make the manipulators useful, some force feedback is required to enable the operator to sense the robot’s feelings. Without force feedback, many tasks will not be able to be carried out. For these reasons, a master slave system with different kinematics has been developed. The system permits us to vary the ratio of the position/attitude, to design a master manipulator without considering the kinematics of the slave manipulator, and so on. To overcome the difficulties, a master slave manipulator system with different kinematics is proposed. The master manipulator is force controlled via a force torque sensor in the handle. As to master slave manipulator system with two way force feedback is concerned, the force goes to the actuator from the operator, and come back to the operator from the actuator. The working situation is viewed by the stereo TV supervisory system. The force and vision telepresence are thus achieved. In order to ensure the maneuverability, direct drive DC motors and PWM servo units are adopted to improve the response speed. It can provide force response in a wide range. A lot of experiments were performed with the master slave manipulator system force telepresence to study the force response under restricted environment. By two force sensors, the force position bilateral force response system effectively decreases the affection of friction and inertia force, and increases the authenticity of bilateral force response. When the slave manipulator arm is encountered with soft object(sponge), in the experiments, the operator can clearly have the fine feeling as if he himself is contacted with the object.展开更多
A 3 DOF master-slave telerobot system is established for study on force telepresence technology. A force feedback and position control scheme is adopted in the bilateral force response control system,and force fidelit...A 3 DOF master-slave telerobot system is established for study on force telepresence technology. A force feedback and position control scheme is adopted in the bilateral force response control system,and force fidelity and controllability experiments demonstrate feasibility of the con-trol system.展开更多
A microwave power-combining system composed of two Panasonic 2M244-M1 magnetrons based on master–slave injection-locking is demonstrated in this paper. The principle of master–slave injection-locking and the locking...A microwave power-combining system composed of two Panasonic 2M244-M1 magnetrons based on master–slave injection-locking is demonstrated in this paper. The principle of master–slave injection-locking and the locking condition are theoretical analyzed. Experimental results are consistent with the theoretical analysis and the experimental combined efficiency is higher than 96%. Compared with the external-injection-locked system, the power-combining based on the master–slave injection-locking magnetron is superior by taking out the external solid-state driver and the real-time phase control system. Thus, this power-combining system has great potential for obtaining a high efficiency, high stability, low cost, and high power microwave source.展开更多
This paper proposes an adaptive synchronization problem for the master and slave structure of linear systems with nonlinear perturbations and mixed time-varying delays comprising different discrete and distributed tim...This paper proposes an adaptive synchronization problem for the master and slave structure of linear systems with nonlinear perturbations and mixed time-varying delays comprising different discrete and distributed time delays. Using an appropriate Lyapunov-Krasovskii functional, some delay-dependent sufficient conditions and an adaptation law including the master-slave parame- ters are established for designing a delayed synchronization law in terms of linear matrix inequalities（LMIs）. The time-varying controller guarantees the H ∞ synchronization of the two coupled master and slave systems regardless of their initial states. Particularly, it is shown that the synchronization speed can be controlled by adjusting the updated gain of the synchronization signal. Two numerical examples are given to demonstrate the effectiveness of the method.展开更多
Welding seam tracking precision was decreased due to human hand tremor during the master-slave welding teleoperation. To solve this problem, a master-slave robot remote welding system was built, the system consisted o...Welding seam tracking precision was decreased due to human hand tremor during the master-slave welding teleoperation. To solve this problem, a master-slave robot remote welding system was built, the system consisted of a master manipulator with six degree of freedom （ DOF ） , an industrial computer control system and a slave Motoman HP3 J robot, and human hand tremor and digital filtering were discussed. An optimal digital filter was designed to clean human tremor signal for improving the welding seam tracking precision. The experimental results show that the digital filter suppresses the operator＇ s tremor signal.展开更多
This study aims to address the feasibility of planned islanding operation and to investigate the effect of unplanned islanding using the master-slave islanding method for controlling the distributed generation units d...This study aims to address the feasibility of planned islanding operation and to investigate the effect of unplanned islanding using the master-slave islanding method for controlling the distributed generation units during grid-connected and islanding operation. Neplan desktop power simulation tool was used for the modelling and simulation of a realistic MV network with four different distributed generation technologies (diesel, gas, hydro and wind) along with their excitation and governor control systems, while an exponential model was used to represent the loads in the network. The dynamic and steady state behavior of the four distributed generation technologies were investigated during grid-connected operation and two transition modes to the islanding situation, planned and unplanned. The obtained results that validated through various case studies have shown that a suitable planned islanding transition could provide support to critical loads at the event of electricity utility outages.展开更多
基金supported by the Key Project of Chinese Ministry of Education(108037)the National Natural Science Foundation of China(10402008 and 50535010)
文摘This paper addresses a master-slave synchro- nization strategy for complex dynamic systems based on feedback control. This strategy is applied to 3-DOF pla- nar manipulators in order to obtain synchronization in such complicated as chaotic motions of end-effectors. A chaotic curve is selected from Duffing equation as the trajectory of master end-effector and a piecewise approximation method is proposed to accurately represent this chaotic trajectory of end-effectors. The dynamical equations of master-slave manipulators with synchronization controller are derived, and the Lyapunov stability theory is used to determine the stability of this controlled synchronization system. In numer- ical experiments, the synchronous motions of end-effectors as well as three joint angles and torques of master-slave manipulators are studied under the control of the proposed synchronization strategy. It is found that the positive gain matrix affects the implementation of synchronization con- trol strategy. This synchronization control strategy proves the synchronization＇s feasibility and controllability for com- plicated motions generated by master-slave manipulators.
文摘In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.
文摘Aiming at the weaknesses of LON bus, combining the coexistence of fieldbus and DCS (Distribu ted Control Systems) in control networks, the authors introduce a hierarchical hybrid control network design based on LON and master slave RS 422/485 protocol. This design adopts LON as the trunk, master slave RS 422/485 control networks are connected to LON as special subnets by dedicated gateways. It is an implementation method for isomerous control network integration. Data management is ranked according to real time requirements for different network data. The core components, such as control network nodes, router and gateway, are detailed in the paper. The design utilizes both communication advantage of LonWorks technology and the more powerful control ability of universal MCUs or PLCs, thus it greatly increases system response speed and performance cost ratio.
基金the National Natural Science Foundation of China(No.62211540723)the Interdisciplinary Program of Shanghai Jiao Tong University(Nos.YG2023ZD05 and YG2023ZD14)+1 种基金the Quanzhou High-Level Talent Innovation and Entrepreneurship Project(No.2021C003R)the Research Project of Institute of Medical Robotics of Shanghai Jiao Tong University。
文摘Master robots are integral components of teleoperated robot-assisted minimally invasive surgery systems.Among them,parallel mechanism-based 6-degree-of-freedom master robots are distinguished by low inertia and high-force feedback.However,complex kinematics and singularities are the main barriers limiting its usage.This study converts the Hexa-type 6-RUS mechanism into a master robot to construct master-slave teleoperation system.The clinical background is briefly introduced and a representative surgical robot is employed to analyze the master-slave mapping relationship.The inverse/forward kinematics,the Jacobian matrix,and the translation and orientation workspace are derived as the bases of master robot’s application.The architecture parameters are optimized by the global transmission index to achieve better motion/force transmissibility.Based on the optimal result,the prototype and the master-slave control loop are constructed.Finally,the corresponding master-slave teleoperation experiment and model experiment demonstrate that the proposed master robot satisfies the basic need for medical application.
文摘Content Addressable Memory (CAM) is a type of memory used for high-speed search applications. Due to parallel comparison feature, the CAM memory leads to large power consumption which is caused by frequent pre-charge or discharge of match line. In this paper, CAM for automatic charge balancing with self-control mechanism is proposed to control the voltage swing of ML for reducing the power consumption of CAM. Another technique to reduce the power dissipation is to use MSML, it combines the master-slave architecture with charge minimization technique. Unlike the conventional design, only one match line (ML) is used, whereas in Master-Slave Match Line (MSML) one master ML and several slave MLs are used to reduce the power dissipation in CAM caused by match lines (MLs). Theoretically, the match line (ML) reduces the power consumption up to 50% which is independent of search and match case. The simulation results using Cadence tool of MSML show the reduced power consumption in CAM and modified CAM cell.
基金supported by the National Natural Science Foundation of China (Grant Nos. 60904046, 60972164, 60974071, and 60804006)the Special Fund for Basic Scientific Research of Central Colleges, Northeastern University, China (Grant No. 090604005)+2 种基金the Science and Technology Program of Shenyang (Grant No. F11-264-1-70)the Program for Liaoning Excellent Talents in University (Grant No. LJQ2011137)the Program for Liaoning Innovative Research Team in University (Grant No. LT2011019)
文摘The networked synchronization problem of a class of master-slave chaotic systems with time-varying communication topologies is investigated in this paper. Based on algebraic graph theory and matrix theory, a simple linear state feedback controller is designed to synchronize the master chaotic system and the slave chaotic systems with a time- varying communication topology connection. The exponential stability of the closed-loop networked synchronization error system is guaranteed by applying Lyapunov stability theory. The derived novel criteria are in the form of linear matrix inequalities （LMIs）, which are easy to examine and tremendously reduce the computation burden from the feedback matrices. This paper provides an alternative networked secure communication scheme which can be extended conveniently. An illustrative example is given to demonstrate the effectiveness of the proposed networked synchronization method.
文摘In order to make the manipulators useful, some force feedback is required to enable the operator to sense the robot’s feelings. Without force feedback, many tasks will not be able to be carried out. For these reasons, a master slave system with different kinematics has been developed. The system permits us to vary the ratio of the position/attitude, to design a master manipulator without considering the kinematics of the slave manipulator, and so on. To overcome the difficulties, a master slave manipulator system with different kinematics is proposed. The master manipulator is force controlled via a force torque sensor in the handle. As to master slave manipulator system with two way force feedback is concerned, the force goes to the actuator from the operator, and come back to the operator from the actuator. The working situation is viewed by the stereo TV supervisory system. The force and vision telepresence are thus achieved. In order to ensure the maneuverability, direct drive DC motors and PWM servo units are adopted to improve the response speed. It can provide force response in a wide range. A lot of experiments were performed with the master slave manipulator system force telepresence to study the force response under restricted environment. By two force sensors, the force position bilateral force response system effectively decreases the affection of friction and inertia force, and increases the authenticity of bilateral force response. When the slave manipulator arm is encountered with soft object(sponge), in the experiments, the operator can clearly have the fine feeling as if he himself is contacted with the object.
文摘A 3 DOF master-slave telerobot system is established for study on force telepresence technology. A force feedback and position control scheme is adopted in the bilateral force response control system,and force fidelity and controllability experiments demonstrate feasibility of the con-trol system.
基金Project supported by the National Basic Research Program of China(Grant No.2013CB328902)the National Natural Science Foundation of China(Grant No.61501311)
文摘A microwave power-combining system composed of two Panasonic 2M244-M1 magnetrons based on master–slave injection-locking is demonstrated in this paper. The principle of master–slave injection-locking and the locking condition are theoretical analyzed. Experimental results are consistent with the theoretical analysis and the experimental combined efficiency is higher than 96%. Compared with the external-injection-locked system, the power-combining based on the master–slave injection-locking magnetron is superior by taking out the external solid-state driver and the real-time phase control system. Thus, this power-combining system has great potential for obtaining a high efficiency, high stability, low cost, and high power microwave source.
文摘This paper proposes an adaptive synchronization problem for the master and slave structure of linear systems with nonlinear perturbations and mixed time-varying delays comprising different discrete and distributed time delays. Using an appropriate Lyapunov-Krasovskii functional, some delay-dependent sufficient conditions and an adaptation law including the master-slave parame- ters are established for designing a delayed synchronization law in terms of linear matrix inequalities（LMIs）. The time-varying controller guarantees the H ∞ synchronization of the two coupled master and slave systems regardless of their initial states. Particularly, it is shown that the synchronization speed can be controlled by adjusting the updated gain of the synchronization signal. Two numerical examples are given to demonstrate the effectiveness of the method.
基金This research is supported by National Natural Science Foundation of China （No. 50905043）.
文摘Welding seam tracking precision was decreased due to human hand tremor during the master-slave welding teleoperation. To solve this problem, a master-slave robot remote welding system was built, the system consisted of a master manipulator with six degree of freedom （ DOF ） , an industrial computer control system and a slave Motoman HP3 J robot, and human hand tremor and digital filtering were discussed. An optimal digital filter was designed to clean human tremor signal for improving the welding seam tracking precision. The experimental results show that the digital filter suppresses the operator＇ s tremor signal.
文摘This study aims to address the feasibility of planned islanding operation and to investigate the effect of unplanned islanding using the master-slave islanding method for controlling the distributed generation units during grid-connected and islanding operation. Neplan desktop power simulation tool was used for the modelling and simulation of a realistic MV network with four different distributed generation technologies (diesel, gas, hydro and wind) along with their excitation and governor control systems, while an exponential model was used to represent the loads in the network. The dynamic and steady state behavior of the four distributed generation technologies were investigated during grid-connected operation and two transition modes to the islanding situation, planned and unplanned. The obtained results that validated through various case studies have shown that a suitable planned islanding transition could provide support to critical loads at the event of electricity utility outages.
