Herein,a series of manganese oxide catalysts with different valences(Mn_(3)O_(4),Mn_(2)O_(3),and MnO_(2))were designed and synthesized for the synthesis of ethylene urea(EU)from ethylenediamine(EDA)and carbon dioxide(...Herein,a series of manganese oxide catalysts with different valences(Mn_(3)O_(4),Mn_(2)O_(3),and MnO_(2))were designed and synthesized for the synthesis of ethylene urea(EU)from ethylenediamine(EDA)and carbon dioxide(CO_(2)).With a maximal EDA conversion of 82%and EU selectivity of 99%at 160℃ for 2 h,Mn_(2)O_(3) catalysts had the best catalytic activity among them,which was superior to the reported catalysts.In the following order:Mn_(2)O_(3)>MnO_(2)>Mn_(3)O_(4),the catalytic activity for the synthesis of EU from CO_(2) and EDA decreased.Further characterization showed the Mn_(2)O_(3) catalyst possessed a greater Mn^(3+)/Mn4+ratio and more surface oxygen vacancies than the MnO_(2) and Mn_(3)O_(4),which improved its capacity to adsorb and activate CO_(2) and EDA.After four recycling runs,the EDA conversion slightly declined from 82%to 56%on Mn_(2)O_(3) catalyst,while no obvious change in EU selectivity was observed.The loss of surface Ov contents and Mn^(3+)proportion were concluded as main reasons for the decrease in catalytic activity over Mn_(2)O_(3) catalyst.This work demonstrated a metal oxide catalyst that was efficient in producing EU from CO_(2) and EDA.展开更多
A series of copper manganese oxides were prepared using a selective etching technique with various amounts of ammonia added during the co-precipitation process. The effect of the ammonia etching on the structure and c...A series of copper manganese oxides were prepared using a selective etching technique with various amounts of ammonia added during the co-precipitation process. The effect of the ammonia etching on the structure and catalytic properties of the copper manganese oxides was investigated using elemental analysis, nitrogen physisorption, X-ray powder diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, H2 temperature-programmed reduc- tion, and Oz temperature-programmed desorption combined with catalytic oxidation of CO. It was found that ammonia can selectively remove copper species from the copper manganese oxides, which correspondingly generates more defects in these oxides. An oxygen spillover from the man- ganese to the copper species was observed by H2 temperature-programmed desorption, indicating that ammonia etching enhanced the mobility of lattice oxygen species in these oxides. The Oz tem- perature-programmed desorption measurements further revealed that ammonia etching improved the ability of these oxides to release lattice oxygen. The improvement in redox properties of the copper manganese oxides following ammonia etching was associated with enhanced catalytic performance for CO oxidation.展开更多
The effects of calcination temperature on the physicochemical properties of manganese oxide catalysts prepared by a precipitation method were assessed by X-ray diffraction,N2 adsorption-desorption,X-ray photoelectron ...The effects of calcination temperature on the physicochemical properties of manganese oxide catalysts prepared by a precipitation method were assessed by X-ray diffraction,N2 adsorption-desorption,X-ray photoelectron spectroscopy,H2 temperature-programmed reduction,O2 temperature-programmed desorption,and thermogravimetry-differential analysis.The catalytic performance of each of these materials during the selective oxidation of cyclohexane with oxygen in a solvent-free system was subsequently examined.It was found that the MnOx-500 catalyst,calcined at 500 °C,consisted of a Mn2O3 phase in addition to Mn5O8 and Mn3O4 phases and possessed a low surface area.Unlike MnOx-500,the MnOx-400 catalyst prepared at 400 °C was composed solely of Mn3O4 and Mn5O8 and had a higher surface area.The pronounced catalytic activity of this latter material for the oxidation of cyclohexene was determined to result from numerous factors,including a higher concentration of surface adsorbed oxygen,greater quantities of the surface Mn4＋ ions that promote oxygen mobility and the extent of O2 adsorption and reducibility on the catalyst.The effects of various reaction conditions on the activity of the MnOx-400 during the oxidation of cyclohexane were also evaluated,such as the reaction temperature,reaction time,and initial oxygen pressure.Following a 4 h reaction at an initial O2 pressure of 0.5 MPa and 140 °C,an 8.0% cyclohexane conversion and 5.0% yield of cyclohexanol and cyclohexanone were achieved over the MnOx-400 catalyst.In contrast,employing MnOx-500 resulted in a 6.1% conversion of cyclohexane and 75% selectivity for cyclohexanol and cyclohexanone.After being recycled through 10 replicate uses,the catalytic activity of the MnOx-400 catalyst was unchanged,demonstrating its good stability.展开更多
The influence of Ce doping and the precipitation method on structural properties and the catalytic activity of copper manganese oxides for CO oxidation at ambient temperature have been investigated. The catalysts were...The influence of Ce doping and the precipitation method on structural properties and the catalytic activity of copper manganese oxides for CO oxidation at ambient temperature have been investigated. The catalysts were characterized by means of the powder X-ray diffraction and N2 adsorption-desorption, the inductively coupled plasma atomic emission spectrometry, the temperature programmed reduction, diffuse reflectance UV-Vis spectra, and the X-ray photoelectron spectroscopy. It was found that after doping little amount of Ce in copper manganese oxide, CeO2 phase was highly dispersed and could prevent sintering and aggregating of the catalyst, the size of the catalytic material was decreased, the reducibility was enhanced, the specific surface area was increased and the formation of the active sites for the oxidation of CO was improved significantly. Therefore, the activity of the rare earth promoted catalyst was enhanced remarkably.展开更多
Manganese oxides are known as one type of semiconductors,but their photocatalysis characteristics have not been deeply explored.In this study,photocatalytic degradation of phenol using several synthesized manganese ox...Manganese oxides are known as one type of semiconductors,but their photocatalysis characteristics have not been deeply explored.In this study,photocatalytic degradation of phenol using several synthesized manganese oxides,i.e,acidic birnessite （BIR-H）,alkaline birnessite （BIR-OH）,cryptomelane （CRY） and todorokite （TOD）,were comparatively investigated.To elucidate phenol degradation mechanisms,X-ray diffraction （XRD）,ICP-AES （inductively coupled plasma-atomic emission spectroscopy）,TEM （transmission electronic microscope）,N 2 physisorption at 77 K and UV-visible diffuse reflectance spectroscopy （UV-Vis DRS） were employed to characterize the structural,compositional,morphological,specific surface area and optical absorption properties of the manganese oxides.After 12 hr of UV-Vis irradiation,the total organic carbon （TOC） removal rate reached 62.1%,43.1%,25.4%,and 22.5% for cryptomelane,acidic birnessite,todorokite and alkaline birnessite,respectively.Compared to the reactions in the dark condition,UV- Vis exposure improved the TOC removal rates by 55.8%,31.9%,23.4% and 17.9%.This suggests a weak ability of manganese oxides to degrade phenol in the dark condition,while UV-Vis light irradiation could significantly enhance phenol degradation.The manganese minerals exhibited photocatalytic activities in the order of：CRY BIR-H TOD BIR-OH.There may be three possible mechanisms for photochemical degradation：（1） direct photolysis of phenol;（2） direct oxidation of phenol by manganese oxides;（3） photocatalytic oxidation of phenol by manganese oxides.Photocatalytic oxidation of phenol appeared to be the dominant mechanism.展开更多
Various manganese oxides(MnOx) prepared via citric acid solution combustion synthesis were applied for catalytic oxidation of benzene. The results showed the ratios of citric acid/manganese nitrate in synthesizing pro...Various manganese oxides(MnOx) prepared via citric acid solution combustion synthesis were applied for catalytic oxidation of benzene. The results showed the ratios of citric acid/manganese nitrate in synthesizing process positively affected the physicochemical properties of MnOx, e.g., BET(Brunauer-Emmett-Teller) surface area, porous structure, reducibility and so on, which were in close relationship with their catalytic performance. Of all the catalysts, the sample prepared at a citric acid/manganese nitrate ratio of 2:1(C2M1) displayed the best catalytic activity with T(90)(the temperature when 90% of benzene was catalytically oxidized) of 212 ℃. Further investigation showed that C2M1 was Mn2O3 with abundant nano-pores, the largest surface area and the proper ratio of surface Mn^4+/Mn^3+, resulting in preferable low-temperature reducibility and abundant surface active adsorbed oxygen species. The analysis results of the in-situ Fourier transform infrared spectroscopy(in-situ FTIR) revealed that the benzene was successively oxidized to phenolate, o-benzoquinone, small molecules(such as maleates, acetates, and vinyl), and finally transformed to CO2 and H2O.展开更多
The high oxidation ability of manganese oxides or soils was used to study effects of pH and coatingon Cr(Ⅲ) oxidation. The results indicated that Cr(Ⅲ) oxidation peaked in pH 4.0-6.5. The amount andrate of Cr(Ⅲ) be...The high oxidation ability of manganese oxides or soils was used to study effects of pH and coatingon Cr(Ⅲ) oxidation. The results indicated that Cr(Ⅲ) oxidation peaked in pH 4.0-6.5. The amount andrate of Cr(Ⅲ) being oxidized by uncoated δ-MnO2 were larger than those by Fe oxide- or CaCO3-coatedone. Inorganic Cr(Ⅲ) was more easi1y oxidized by MnO2 than organic complex Cr(Ⅲ) due to differentsurface affinities. Precipitated Cr(Ⅲ) and adsorbed Cr(Ⅲ) might be transferred onto MnO2 surface andthen oxidized to Cr(VI).展开更多
The oxidation of antimony （Ⅲ） in soils was studied using X-ray absorption fine structure （XAFS） spectra. An andosol soft sample and artificial soil samples （SiO2 blended with iron （Ⅲ） hydroxide and manganese...The oxidation of antimony （Ⅲ） in soils was studied using X-ray absorption fine structure （XAFS） spectra. An andosol soft sample and artificial soil samples （SiO2 blended with iron （Ⅲ） hydroxide and manganese （Ⅳ） oxide） were used herein. After adding antimony （Ⅲ） oxide to all soil samples, the oxidation process was observed by recording the XAFS spectra of Sb K-edge, Fe Kedge, and Mn K-edge. The results indicated that manganese （Ⅳ） oxide played an important role in the oxidation of Sb（Ⅲ）; however iron （Ⅲ） hydroxide was not directly related to the reaction. During a 2-hr continuous Sb K-edge X-ray absorption near edge structure （XANES） measurement with an interval of I rain of one of the artificial soil samples （SiO2 ＋ MnO2 ＋ Sb2O3）, a pseudo-first-order reaction was determined with an average estimated rate of 0.52 ±0.04 hr-1. Compared to the lower oxidation rate of andosol, it is suggested that because of the low concentration of Mn（Ⅳ） in natural soils, the oxidation process of Sb（Ⅲ） might be relatively slow and require more time to convert Sb（Ⅲ） to Sb（V）.展开更多
Mangenese oxides were synthesized using two new methods,a novel solvent‐free reaction and a reflux technique,that produced cryptomelane‐type products(K‐OMS‐2).Oxides were also synthesized using conventional method...Mangenese oxides were synthesized using two new methods,a novel solvent‐free reaction and a reflux technique,that produced cryptomelane‐type products(K‐OMS‐2).Oxides were also synthesized using conventional methods and all specimens were applied to the oxidation of ethyl acetate and butyl acetate,acting as models for the volatile organic compounds found in industrial emissions.The catalysts were also characterized using N2adsorption,X‐ray diffraction,scanning electron microscopy,temperature programmed reduction and X‐ray photoelectron spectroscopy.Each of the manganese oxides was found to be very active during the oxidation of both esters to CO2,and the synthesis methodology evidently had a significant impact on catalytic performance.The K‐OMS‐2nanorods synthesized by the solvent‐free method showed higher activity than K‐OMS‐2materials prepared by the reflux technique,and samples with cryptomelane were more active than those prepared by the conventional methods.The catalyst with the highest performance also exhibited good stability and allowed90%conversion of ethyl and butyl acetate to CO2at213and202°C,respectively.Significant differences in the catalyst performance were observed,clearly indicating that K‐OMS‐2nanorods prepared by the solvent‐free reaction were better catalysts for the selected VOC oxidations than the mixtures of manganese oxides traditionally obtained with conventional synthesis methods.The superior performance of the K‐OMS‐2catalysts might be related to the increased average oxidation state of the manganese in these structures.Significant correlations between the catalytic performance and the surface chemical properties were also identified,hig-hlighting the K‐OMS‐2properties associated with the enhanced catalytic performance of the materials.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.展开更多
MnO_x-CeO_2 catalysts were synthesized to investigate the active sites for NO oxidation by varying the calcination temperature. XRD and TEM results showed that cubic CeO_2 and amorphous MnO_x existed in MnO_x-CeO_2 ca...MnO_x-CeO_2 catalysts were synthesized to investigate the active sites for NO oxidation by varying the calcination temperature. XRD and TEM results showed that cubic CeO_2 and amorphous MnO_x existed in MnO_x-CeO_2 catalysts. High temperature calcination caused the sintering of amorphous MnO_x and transforming to bulk crystalline Mn_2O_3, H_2-TPR and XPS results suggested the valence of Mn in MnO_x-CeO_2 was higher than pure MnO_x, and decreased with the increasing calcination temperature, The turnover frequency（TOF） was calculated based on the initial reducibility according to H_2-TPR quantitation and kinetic study. The TOF results indicated that the initial reducibility of amorphous MnO_x with high valence manganese ions was equivalent to the active sites for NO oxidation. It can be inferred that the amorphous MnO_x plays a key role in low-temperature NO oxidation.展开更多
The performances of heterogeneous catalysts can be effectively tuned by changing the catalyst structures.Here we report a controllable nitrile synthesis from alcohol ammoxidation,where the nitrile hydration side react...The performances of heterogeneous catalysts can be effectively tuned by changing the catalyst structures.Here we report a controllable nitrile synthesis from alcohol ammoxidation,where the nitrile hydration side reaction could be efficiently prevented by changing the manganese oxide catalysts.α-Mn_(2)O_(3)based catalysts are highly selective for nitrile synthesis,but MnO_(2)-based catalysts includingα,β,γ,andδphases favour the amide production from tandem ammoxidation and hydration steps.Multiple structural,kinetic,and spectroscopic investigations reveal that water decomposition is hindered onα-Mn2O3,thus to switch off the nitrile hydration.In addition,the selectivity-control feature of manganese oxide catalysts is mainly related to their crystalline nature rather than oxide morphology,although the morphological issue is usually regarded as a crucial factor in many reactions.展开更多
Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is...Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is restricted due to its unsatisfactory oxidant activation efficiency.Fortunately,recently remarkable research on deep activation mechanisms and modification of MNO_(x)have been undertaken to improve its reactivity.Herein,modification enhancement mechanisms of MNO_(x)to efficiently degrade various organic contaminants were discussed and highlighted,including metal doping,coupling with other metal oxides,composite with carbonaceous material,and compounding with other support.The activation mechanisms of different MNO_(x)and derivative-modified material(such as doped MNO_(x),metal oxide-MNO_(x)hybrids,and MNO_(x)-carbonaceous material hybrids)were summarized in great details,which was specifically categorized into both radical and non-radical pathways.The effects of pH,inorganic ions,and natural organic matter on degradation reactions are also discussed.Finally,future research directions and perspectives are presented to provide a clear interpretation on the MNO_(x)initiated AOPs.展开更多
Three forged low-density high manganese steels Mn28Al10,Mn28Al8 and Mn20Al10 were used as experimental materials in this study.The forged microstructure and external oxidation characteristics at 1323 K and 1373 K for ...Three forged low-density high manganese steels Mn28Al10,Mn28Al8 and Mn20Al10 were used as experimental materials in this study.The forged microstructure and external oxidation characteristics at 1323 K and 1373 K for 5-25 h in air were investigated by microstructural observation and X-ray diffraction（XRD）technique.The phase compositions and abundance in the forged and oxidized samples were quantitatively obtained by Rietveld method on the basis of XRD pattern analysis.The results showed that an austenitic microstructure formed in steels Mn28Al10 and Mn28Al8,and 18.02 wt%ferrite could be found in Mn20Al10.The relative amount of ~5.28 wt%-carbide（Fe_3AlC_（0.5））in Mn28Al10 was far greater than that in Mn28Al8 and Mn20Al10.The oxidation kinetics of forged steels oxidized at 1323 K for 5-25 h had two-stage parabolic rate laws;and the oxidation rate of the first stage was lower than that of the second stage.When they were oxidized at 1373 K for 5-25 h,the oxidation kinetics followed only a parabolic law and the oxidation rates were respectively greater than those at 1323 K for 5-25 h.When they were oxidized at 1323 K for 25 h,detached external scales contained Fe_2MnO_4and-Fe_2O_3oxides.-Al_2O_3and（Fe,Mn）_2O_3oxides could only be indexed in steels Mn28Al8 and Mn28Al10,respectively.When they were oxidized at 1373 K for 25 h,Fe_2MnO_4,Fe_3O_4,-Fe_2O_3 and-Al_2O_3oxides could all be indexed in the external detached scales.The main phase of detached external scales was Fe_2MnO_4;and the relative amount of-Al_2O_3in steel Mn28Al8 was higher than that in steels Mn28Al10 and Mn20Al.The external oxidation layers of these three forged steels oxidized at 1323 K and 1373 K for 25 h were essentially followed the sequence of-Al_2O_3,Fe_2MnO_4,Fe_3O_4,FeMnO_3,and Fe_2O_3from the substrate to the outside surface.The forged Mn28Al10 steel with austenitic microstructure and a certain amount of-carbide（~5.28 wt%in the present work）possessed a better combination of strength,ductility,specific strength,and oxidation rate when compared to that of the forged Mn28Al8 and Mn20Al10 steels.展开更多
The catalytic oxidation of nitrogen oxide( NO) from waste gas was investigated using advanced oxidation process based on sulfate radicals. The manganese oxide immobilized on graphene oxide( GO) can activate peroxymono...The catalytic oxidation of nitrogen oxide( NO) from waste gas was investigated using advanced oxidation process based on sulfate radicals. The manganese oxide immobilized on graphene oxide( GO) can activate peroxymonosulfate( PMS) for the oxidation of NO in waste gas. The Mn3O4 / GO catalyst system was characterized via X-ray diffraction( XRD), Fourier transform infrared spectrocopy( FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy( XPS), energy dispersive X-ray spectroscopy( EDS),and scanning electron microscope( SEM).The results showed that Mn3O4 was distributed on GO. The Mn3O4 /GO catalyst system exhibited efficient activity for NO oxidation when the Mn3O4 /GO catalyst had an optimum Mn3O4 loading. In addition,the best catalytic oxidation could be achieved within 60 min with 0. 25 mmol /L Mn3 O4 /GO catalyst, and2 mmol /L PMS dosage at 25 ℃. The catalysts also exhibited stable performance after several rounds of regeneration. Therefore,the results may have significant technical implication for utilizing Mn3O4 /PMS to oxidize NO for offgas treatment.展开更多
By enhancing surface interaction between metal oxide particles and carbon-based materials,it can effectively improve Faraday capacitance and conductivity,ultimately achieving high energy density with sufficient redox ...By enhancing surface interaction between metal oxide particles and carbon-based materials,it can effectively improve Faraday capacitance and conductivity,ultimately achieving high energy density with sufficient redox reactions in supercapacitors.Through a gentle biomineralization process and subsequent thermal reduction strategy,we successfully prepared the graphene oxide(GO)wrapping mixed-valence manganese oxides(MnO_(x))and S,P self-codoped carbon matrix porous composite(MnO_(x)@SPC@reduced graphene oxide(RGO)).During the biomineralization process of engineered Pseudomonas sp.(Ml)cells,GO nanosheets functioned as the'soil'to adsorb Mn^(2+)ion and uniformly disperse biogenic Mn oxides(BMO).After undergoing annealing,the MnO_(x) nanoparticles were evenly wrapped with graphene,resulting in the creation of the MnO_(x)@SPC@RGO3 composite.This composite possesses strong C—O—Mn bond interfaces,numerous electroactive sites,and a uniform pore structure.By optimizing the synergistic interaction between the highly conductive graphene and the remarkable surface capacitance of MnO_(x),the MnO_(x)@SPC@RGO3 electrode,with its intercalation Faraday reactions mechanism of■transformations,exhibits an outstanding specific capacity(448.3 F·g^(-1)at 0.5 A·g^(-1)),multiplying performance(340.5 F·g^(-1)at10 A·g^(-1)),and cycling stability(93.8%retention after 5000 cycles).Moreover,the asymmetric all-solidstate supercapacitors of MnO_(x)@SPC@RGO3//PC exhibit an exceptional energy density of 64.8 W·h·kg^(-1)and power density of 350 W·kg^(-1),as well as a long lifespan with capacitance retention of 92.5%after10000 cycles.In conclusion,the synthetic route utilizing biomineralization and thermal reduction exhibits significant potential for exploiting high-performance electrode materials in all-solid-state supercapacitor applications.展开更多
Water scarcity,driven by climate change and population growth,necessitates innovative desalination technologies.Conventional methods for brackish water desalination are limited by high-energy demands,especially in the...Water scarcity,driven by climate change and population growth,necessitates innovative desalination technologies.Conventional methods for brackish water desalination are limited by high-energy demands,especially in the low salinity range,prompting the exploration of electrochemical approaches like faradaic deionization.Sodium-manganese oxides,traditionally used in sodium-ion batteries,show promise as faradaic deionization electrode materials due to their abundance,low toxicity,and cost-effectiveness.However,capacity fading during cycling,often caused by structural changes,volume expansion,or chemical transformations,remains a critical challenge.This study investigates the impact of morphology and crystal structure on the electrochemical performance of commercial and synthesized sodium-manganese oxides for faradaic deionization applications.Structural and electrochemical characterization in three-electrode cells with low-concentration electrolytes provided insights into the charge storage mechanisms.Rocking-chair full flow cell experiments demonstrated that the mixed-phase sodium-manganese oxide exhibited superior desalination performance,achieving a high salt removal capacity of 54.5 mg g^(−1)and a mean value in the salt removal rate of 1.49 mg g^(−1)min^(-1).Notably,mixed-phase sodium-manganese oxide maintained 98%capacity retention over 870 cycles,one of the longest reported cycling experiments in this field,effectively mitigating the Jahn-Teller effect.These findings highlight the crucial role of sodium-manganese oxide structure and morphology in electrochemical performance,positioning mixed-phase sodium-manganese oxide as a strong candidate for sustainable water treatment technologies.展开更多
Spinel lithium manganese oxide(LiMn_(2)O_(4), LMO) emerges as a promising cathode material for future stationary energy storage applications due to its high voltage, safety, cost-effectiveness, and electrochemical per...Spinel lithium manganese oxide(LiMn_(2)O_(4), LMO) emerges as a promising cathode material for future stationary energy storage applications due to its high voltage, safety, cost-effectiveness, and electrochemical performance. However,LMO suffers from rapid capacity degradation caused by the Jahn–Teller effect, Mn dissolution and side reactions. The mechanism remains unclear and even contradictory across various studies, impeding the advancement of high-performance LMO and its widespread utilization. In this study, 14 Ah commercial-level LMO batteries were manufactured and assessed.The mechanism of capacity attenuation in cycle-aged cells at room temperature(RT, 25℃) and high temperature(HT,55℃) storage cells was systematically investigated through the application of electrochemical quantitative methods. The results indicate specific capacity losses of approximately 6.26% and 2.55% for the cathodes in RT cycle-aged cells and HT storage cells, respectively, in comparison to fresh cells. These values are lower than the 12.54% and 6.99% capacity losses observed in RT cycle-aged cells and HT storage cells. While RT cycle-aging and HT storage conditions do not lead to irreversible capacity loss on the anode side. The results suggest that the primary causes of irreversible capacity degradation are not located on the cathode or anode. Nevertheless, significant polarization arises from the continuous growth of the solid electrolyte interphase(SEI), believed to be catalyzed by Mn deposited on the anode, which is considered harmful.This study elucidates that inhibiting the dissolution of Mn from the cathode, facilitating its transport in the electrolyte,promoting its deposition on the anode, and catalyzing the decomposition of the electrolyte are crucial factors for enhancing the performance of LMO batteries.展开更多
Manganese oxide ores from Gabon and Xiangxi were leached with waste tea as reductant in dilute sulfuric acid solution. The effects of waste tea dosage, concentration of sulfuric acid, liquid-to-solid ratio, leaching t...Manganese oxide ores from Gabon and Xiangxi were leached with waste tea as reductant in dilute sulfuric acid solution. The effects of waste tea dosage, concentration of sulfuric acid, liquid-to-solid ratio, leaching temperature and reaction time on leaching process were explored. The leaching efficiency of Gabonese manganese oxide ore reached almost 100% under the optimal condition which was determined as follows： manganese oxide ore to waste tea mass ratio of 10：1, sulfuric acid concentration of 2.5 molFL, liquid-to-solid ratio of 7.5：1, leaching temperature of 368 K, time of 8 h. The leaching efficiency of Xiangxi manganese oxide ore reached 99.8% under the optimal condition which was determined as follows： manganese oxide ore to waste tea mass ratio of 10：1, sulfuric acid concentration of 1.7 mol/L, liquid-to-solid ratio of 7.5：1, leaching temperature of 368 K, time of 8 h. The leaching process followed the internal diffusion controlled kinetic model, and the apparent activation energies of Gabonese manganese oxide ore and Xiangxi manganese oxide ore were calculated to be 38.2 kJ/mol and 20.4 kJ/mol, respectively. The morphological changes and mineralogical forms of the ore before and after the chemical treatment were discussed with the support of XRD analysis and SEM analysis.展开更多
Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the ...Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.展开更多
The extraction of manganese from low-grade manganese oxide ores using Ca S derived from Ca SO4 as reductant was investigated. The effects of mass ratio of Ca S to ore, reduction temperature, reduction time, liquid to ...The extraction of manganese from low-grade manganese oxide ores using Ca S derived from Ca SO4 as reductant was investigated. The effects of mass ratio of Ca S to ore, reduction temperature, reduction time, liquid to solid ratio（L/S ratio）, stirring speed, leaching temperature, leaching time and H2SO4 concentration on the leaching rates of Mn and Fe during the reduction–acid leaching process were discussed. The leaching rates of 96.47% for Mn and 19.24% for Fe were obtained under the optimized conditions of mass ratio of Ca S to manganese oxide ore 1：6.7, L/S ratio 5：1, stirring speed 300 r/min, reduction temperature of 95 °C for 2.0 h in the reduction process and leaching stirring speed of 200 r/min, H2SO4 concentration of 1.5 mol/L, leaching temperature of 80 °C for 5 min in the leaching process. In addition, this process can be employed in the recovery of manganese from various manganese oxide ores, and Mn leaching rate above 95% is obtained.展开更多
基金supported by the National Natural Science Foundation of China(No.22278041)the Foundation of State Key Laboratory of High-efficiency Utilization of Coal and Green Chemical Engineering(No.2022-K78)+1 种基金Jiangsu Province Key Laboratory of Fine Petrochemical Engineering(No.KF2107)the Advanced Catalysis and Green Manufacturing Collab-orative Innovation Center(No.ACGM2022-10-07)。
文摘Herein,a series of manganese oxide catalysts with different valences(Mn_(3)O_(4),Mn_(2)O_(3),and MnO_(2))were designed and synthesized for the synthesis of ethylene urea(EU)from ethylenediamine(EDA)and carbon dioxide(CO_(2)).With a maximal EDA conversion of 82%and EU selectivity of 99%at 160℃ for 2 h,Mn_(2)O_(3) catalysts had the best catalytic activity among them,which was superior to the reported catalysts.In the following order:Mn_(2)O_(3)>MnO_(2)>Mn_(3)O_(4),the catalytic activity for the synthesis of EU from CO_(2) and EDA decreased.Further characterization showed the Mn_(2)O_(3) catalyst possessed a greater Mn^(3+)/Mn4+ratio and more surface oxygen vacancies than the MnO_(2) and Mn_(3)O_(4),which improved its capacity to adsorb and activate CO_(2) and EDA.After four recycling runs,the EDA conversion slightly declined from 82%to 56%on Mn_(2)O_(3) catalyst,while no obvious change in EU selectivity was observed.The loss of surface Ov contents and Mn^(3+)proportion were concluded as main reasons for the decrease in catalytic activity over Mn_(2)O_(3) catalyst.This work demonstrated a metal oxide catalyst that was efficient in producing EU from CO_(2) and EDA.
基金supported by the National Basic Research Program of China (973 Program,2013CB934104)the China Postdoctoral Science Foundation(2014M560202)~~
文摘A series of copper manganese oxides were prepared using a selective etching technique with various amounts of ammonia added during the co-precipitation process. The effect of the ammonia etching on the structure and catalytic properties of the copper manganese oxides was investigated using elemental analysis, nitrogen physisorption, X-ray powder diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, H2 temperature-programmed reduc- tion, and Oz temperature-programmed desorption combined with catalytic oxidation of CO. It was found that ammonia can selectively remove copper species from the copper manganese oxides, which correspondingly generates more defects in these oxides. An oxygen spillover from the man- ganese to the copper species was observed by H2 temperature-programmed desorption, indicating that ammonia etching enhanced the mobility of lattice oxygen species in these oxides. The Oz tem- perature-programmed desorption measurements further revealed that ammonia etching improved the ability of these oxides to release lattice oxygen. The improvement in redox properties of the copper manganese oxides following ammonia etching was associated with enhanced catalytic performance for CO oxidation.
基金supported by the National Basic Research Program of China(973 Program,2010CB732300)the National Natural Science Foundation of China(21103048)~~
文摘The effects of calcination temperature on the physicochemical properties of manganese oxide catalysts prepared by a precipitation method were assessed by X-ray diffraction,N2 adsorption-desorption,X-ray photoelectron spectroscopy,H2 temperature-programmed reduction,O2 temperature-programmed desorption,and thermogravimetry-differential analysis.The catalytic performance of each of these materials during the selective oxidation of cyclohexane with oxygen in a solvent-free system was subsequently examined.It was found that the MnOx-500 catalyst,calcined at 500 °C,consisted of a Mn2O3 phase in addition to Mn5O8 and Mn3O4 phases and possessed a low surface area.Unlike MnOx-500,the MnOx-400 catalyst prepared at 400 °C was composed solely of Mn3O4 and Mn5O8 and had a higher surface area.The pronounced catalytic activity of this latter material for the oxidation of cyclohexene was determined to result from numerous factors,including a higher concentration of surface adsorbed oxygen,greater quantities of the surface Mn4＋ ions that promote oxygen mobility and the extent of O2 adsorption and reducibility on the catalyst.The effects of various reaction conditions on the activity of the MnOx-400 during the oxidation of cyclohexane were also evaluated,such as the reaction temperature,reaction time,and initial oxygen pressure.Following a 4 h reaction at an initial O2 pressure of 0.5 MPa and 140 °C,an 8.0% cyclohexane conversion and 5.0% yield of cyclohexanol and cyclohexanone were achieved over the MnOx-400 catalyst.In contrast,employing MnOx-500 resulted in a 6.1% conversion of cyclohexane and 75% selectivity for cyclohexanol and cyclohexanone.After being recycled through 10 replicate uses,the catalytic activity of the MnOx-400 catalyst was unchanged,demonstrating its good stability.
文摘The influence of Ce doping and the precipitation method on structural properties and the catalytic activity of copper manganese oxides for CO oxidation at ambient temperature have been investigated. The catalysts were characterized by means of the powder X-ray diffraction and N2 adsorption-desorption, the inductively coupled plasma atomic emission spectrometry, the temperature programmed reduction, diffuse reflectance UV-Vis spectra, and the X-ray photoelectron spectroscopy. It was found that after doping little amount of Ce in copper manganese oxide, CeO2 phase was highly dispersed and could prevent sintering and aggregating of the catalyst, the size of the catalytic material was decreased, the reducibility was enhanced, the specific surface area was increased and the formation of the active sites for the oxidation of CO was improved significantly. Therefore, the activity of the rare earth promoted catalyst was enhanced remarkably.
基金supported by the National Natural Sci-ence Foundation of China(No.40830527,40771102)the New Century Excellent Talents in University of China(No.NCET-09-0399)
文摘Manganese oxides are known as one type of semiconductors,but their photocatalysis characteristics have not been deeply explored.In this study,photocatalytic degradation of phenol using several synthesized manganese oxides,i.e,acidic birnessite （BIR-H）,alkaline birnessite （BIR-OH）,cryptomelane （CRY） and todorokite （TOD）,were comparatively investigated.To elucidate phenol degradation mechanisms,X-ray diffraction （XRD）,ICP-AES （inductively coupled plasma-atomic emission spectroscopy）,TEM （transmission electronic microscope）,N 2 physisorption at 77 K and UV-visible diffuse reflectance spectroscopy （UV-Vis DRS） were employed to characterize the structural,compositional,morphological,specific surface area and optical absorption properties of the manganese oxides.After 12 hr of UV-Vis irradiation,the total organic carbon （TOC） removal rate reached 62.1%,43.1%,25.4%,and 22.5% for cryptomelane,acidic birnessite,todorokite and alkaline birnessite,respectively.Compared to the reactions in the dark condition,UV- Vis exposure improved the TOC removal rates by 55.8%,31.9%,23.4% and 17.9%.This suggests a weak ability of manganese oxides to degrade phenol in the dark condition,while UV-Vis light irradiation could significantly enhance phenol degradation.The manganese minerals exhibited photocatalytic activities in the order of：CRY BIR-H TOD BIR-OH.There may be three possible mechanisms for photochemical degradation：（1） direct photolysis of phenol;（2） direct oxidation of phenol by manganese oxides;（3） photocatalytic oxidation of phenol by manganese oxides.Photocatalytic oxidation of phenol appeared to be the dominant mechanism.
基金financially supported by the National Key Re-search and Development Plan (No. 2017YFC0211804)。
文摘Various manganese oxides(MnOx) prepared via citric acid solution combustion synthesis were applied for catalytic oxidation of benzene. The results showed the ratios of citric acid/manganese nitrate in synthesizing process positively affected the physicochemical properties of MnOx, e.g., BET(Brunauer-Emmett-Teller) surface area, porous structure, reducibility and so on, which were in close relationship with their catalytic performance. Of all the catalysts, the sample prepared at a citric acid/manganese nitrate ratio of 2:1(C2M1) displayed the best catalytic activity with T(90)(the temperature when 90% of benzene was catalytically oxidized) of 212 ℃. Further investigation showed that C2M1 was Mn2O3 with abundant nano-pores, the largest surface area and the proper ratio of surface Mn^4+/Mn^3+, resulting in preferable low-temperature reducibility and abundant surface active adsorbed oxygen species. The analysis results of the in-situ Fourier transform infrared spectroscopy(in-situ FTIR) revealed that the benzene was successively oxidized to phenolate, o-benzoquinone, small molecules(such as maleates, acetates, and vinyl), and finally transformed to CO2 and H2O.
文摘The high oxidation ability of manganese oxides or soils was used to study effects of pH and coatingon Cr(Ⅲ) oxidation. The results indicated that Cr(Ⅲ) oxidation peaked in pH 4.0-6.5. The amount andrate of Cr(Ⅲ) being oxidized by uncoated δ-MnO2 were larger than those by Fe oxide- or CaCO3-coatedone. Inorganic Cr(Ⅲ) was more easi1y oxidized by MnO2 than organic complex Cr(Ⅲ) due to differentsurface affinities. Precipitated Cr(Ⅲ) and adsorbed Cr(Ⅲ) might be transferred onto MnO2 surface andthen oxidized to Cr(VI).
基金XAFS measurements were carried out at Photon Factory,Tsukuba,Japan(Nos.2014G066,2016G086).
文摘The oxidation of antimony （Ⅲ） in soils was studied using X-ray absorption fine structure （XAFS） spectra. An andosol soft sample and artificial soil samples （SiO2 blended with iron （Ⅲ） hydroxide and manganese （Ⅳ） oxide） were used herein. After adding antimony （Ⅲ） oxide to all soil samples, the oxidation process was observed by recording the XAFS spectra of Sb K-edge, Fe Kedge, and Mn K-edge. The results indicated that manganese （Ⅳ） oxide played an important role in the oxidation of Sb（Ⅲ）; however iron （Ⅲ） hydroxide was not directly related to the reaction. During a 2-hr continuous Sb K-edge X-ray absorption near edge structure （XANES） measurement with an interval of I rain of one of the artificial soil samples （SiO2 ＋ MnO2 ＋ Sb2O3）, a pseudo-first-order reaction was determined with an average estimated rate of 0.52 ±0.04 hr-1. Compared to the lower oxidation rate of andosol, it is suggested that because of the low concentration of Mn（Ⅳ） in natural soils, the oxidation process of Sb（Ⅲ） might be relatively slow and require more time to convert Sb（Ⅲ） to Sb（V）.
基金This work was supported by project “AIProcMat@N2020‐Advanced Industrial Processes and Materials for a Sustainable Northern Region of Portugal 2020”, with the reference NORTE‐01‐0145‐FEDER‐000006, supported by Norte Portugal Regional Operational Programme
文摘Mangenese oxides were synthesized using two new methods,a novel solvent‐free reaction and a reflux technique,that produced cryptomelane‐type products(K‐OMS‐2).Oxides were also synthesized using conventional methods and all specimens were applied to the oxidation of ethyl acetate and butyl acetate,acting as models for the volatile organic compounds found in industrial emissions.The catalysts were also characterized using N2adsorption,X‐ray diffraction,scanning electron microscopy,temperature programmed reduction and X‐ray photoelectron spectroscopy.Each of the manganese oxides was found to be very active during the oxidation of both esters to CO2,and the synthesis methodology evidently had a significant impact on catalytic performance.The K‐OMS‐2nanorods synthesized by the solvent‐free method showed higher activity than K‐OMS‐2materials prepared by the reflux technique,and samples with cryptomelane were more active than those prepared by the conventional methods.The catalyst with the highest performance also exhibited good stability and allowed90%conversion of ethyl and butyl acetate to CO2at213and202°C,respectively.Significant differences in the catalyst performance were observed,clearly indicating that K‐OMS‐2nanorods prepared by the solvent‐free reaction were better catalysts for the selected VOC oxidations than the mixtures of manganese oxides traditionally obtained with conventional synthesis methods.The superior performance of the K‐OMS‐2catalysts might be related to the increased average oxidation state of the manganese in these structures.Significant correlations between the catalytic performance and the surface chemical properties were also identified,hig-hlighting the K‐OMS‐2properties associated with the enhanced catalytic performance of the materials.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.
基金Project supported by the National key research and development program(2016YFC0204901)the National Natural Science Foundation of China(21576207)the introduction of talent and technology cooperation plan of Tianjin(14RCGFGX00849)
文摘MnO_x-CeO_2 catalysts were synthesized to investigate the active sites for NO oxidation by varying the calcination temperature. XRD and TEM results showed that cubic CeO_2 and amorphous MnO_x existed in MnO_x-CeO_2 catalysts. High temperature calcination caused the sintering of amorphous MnO_x and transforming to bulk crystalline Mn_2O_3, H_2-TPR and XPS results suggested the valence of Mn in MnO_x-CeO_2 was higher than pure MnO_x, and decreased with the increasing calcination temperature, The turnover frequency（TOF） was calculated based on the initial reducibility according to H_2-TPR quantitation and kinetic study. The TOF results indicated that the initial reducibility of amorphous MnO_x with high valence manganese ions was equivalent to the active sites for NO oxidation. It can be inferred that the amorphous MnO_x plays a key role in low-temperature NO oxidation.
文摘The performances of heterogeneous catalysts can be effectively tuned by changing the catalyst structures.Here we report a controllable nitrile synthesis from alcohol ammoxidation,where the nitrile hydration side reaction could be efficiently prevented by changing the manganese oxide catalysts.α-Mn_(2)O_(3)based catalysts are highly selective for nitrile synthesis,but MnO_(2)-based catalysts includingα,β,γ,andδphases favour the amide production from tandem ammoxidation and hydration steps.Multiple structural,kinetic,and spectroscopic investigations reveal that water decomposition is hindered onα-Mn2O3,thus to switch off the nitrile hydration.In addition,the selectivity-control feature of manganese oxide catalysts is mainly related to their crystalline nature rather than oxide morphology,although the morphological issue is usually regarded as a crucial factor in many reactions.
基金the National Natural Science Foundation of China(Nos.52170088 and 52070133)for financial support。
文摘Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is restricted due to its unsatisfactory oxidant activation efficiency.Fortunately,recently remarkable research on deep activation mechanisms and modification of MNO_(x)have been undertaken to improve its reactivity.Herein,modification enhancement mechanisms of MNO_(x)to efficiently degrade various organic contaminants were discussed and highlighted,including metal doping,coupling with other metal oxides,composite with carbonaceous material,and compounding with other support.The activation mechanisms of different MNO_(x)and derivative-modified material(such as doped MNO_(x),metal oxide-MNO_(x)hybrids,and MNO_(x)-carbonaceous material hybrids)were summarized in great details,which was specifically categorized into both radical and non-radical pathways.The effects of pH,inorganic ions,and natural organic matter on degradation reactions are also discussed.Finally,future research directions and perspectives are presented to provide a clear interpretation on the MNO_(x)initiated AOPs.
基金financially supported by the National Natural Science Foundation of China(Grant No.51674004)the Education Department of Anhui Province of China(No.KJ2016A104,KJ2017A805)
文摘Three forged low-density high manganese steels Mn28Al10,Mn28Al8 and Mn20Al10 were used as experimental materials in this study.The forged microstructure and external oxidation characteristics at 1323 K and 1373 K for 5-25 h in air were investigated by microstructural observation and X-ray diffraction（XRD）technique.The phase compositions and abundance in the forged and oxidized samples were quantitatively obtained by Rietveld method on the basis of XRD pattern analysis.The results showed that an austenitic microstructure formed in steels Mn28Al10 and Mn28Al8,and 18.02 wt%ferrite could be found in Mn20Al10.The relative amount of ~5.28 wt%-carbide（Fe_3AlC_（0.5））in Mn28Al10 was far greater than that in Mn28Al8 and Mn20Al10.The oxidation kinetics of forged steels oxidized at 1323 K for 5-25 h had two-stage parabolic rate laws;and the oxidation rate of the first stage was lower than that of the second stage.When they were oxidized at 1373 K for 5-25 h,the oxidation kinetics followed only a parabolic law and the oxidation rates were respectively greater than those at 1323 K for 5-25 h.When they were oxidized at 1323 K for 25 h,detached external scales contained Fe_2MnO_4and-Fe_2O_3oxides.-Al_2O_3and（Fe,Mn）_2O_3oxides could only be indexed in steels Mn28Al8 and Mn28Al10,respectively.When they were oxidized at 1373 K for 25 h,Fe_2MnO_4,Fe_3O_4,-Fe_2O_3 and-Al_2O_3oxides could all be indexed in the external detached scales.The main phase of detached external scales was Fe_2MnO_4;and the relative amount of-Al_2O_3in steel Mn28Al8 was higher than that in steels Mn28Al10 and Mn20Al.The external oxidation layers of these three forged steels oxidized at 1323 K and 1373 K for 25 h were essentially followed the sequence of-Al_2O_3,Fe_2MnO_4,Fe_3O_4,FeMnO_3,and Fe_2O_3from the substrate to the outside surface.The forged Mn28Al10 steel with austenitic microstructure and a certain amount of-carbide（~5.28 wt%in the present work）possessed a better combination of strength,ductility,specific strength,and oxidation rate when compared to that of the forged Mn28Al8 and Mn20Al10 steels.
基金Education Innovation Project of Shanghai,China(No.12ZZ069)Natural Science Foundation of Shanghai,China(No.11ZR1400400)+1 种基金Doctoral Fund of Ministry of Education of China(No.20130075110006)Modification Fiber Materials Project of the National Key Laboratory of China(No.LK1203)
文摘The catalytic oxidation of nitrogen oxide( NO) from waste gas was investigated using advanced oxidation process based on sulfate radicals. The manganese oxide immobilized on graphene oxide( GO) can activate peroxymonosulfate( PMS) for the oxidation of NO in waste gas. The Mn3O4 / GO catalyst system was characterized via X-ray diffraction( XRD), Fourier transform infrared spectrocopy( FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy( XPS), energy dispersive X-ray spectroscopy( EDS),and scanning electron microscope( SEM).The results showed that Mn3O4 was distributed on GO. The Mn3O4 /GO catalyst system exhibited efficient activity for NO oxidation when the Mn3O4 /GO catalyst had an optimum Mn3O4 loading. In addition,the best catalytic oxidation could be achieved within 60 min with 0. 25 mmol /L Mn3 O4 /GO catalyst, and2 mmol /L PMS dosage at 25 ℃. The catalysts also exhibited stable performance after several rounds of regeneration. Therefore,the results may have significant technical implication for utilizing Mn3O4 /PMS to oxidize NO for offgas treatment.
基金supported by the National Natural Science Foundation of China(31900005)the Fund of Science and Technology Department of Henan Province(242102231001,242102320362,242102320157)+1 种基金the Fund of Program for Innovative Research Team(in Science and Technology)in University of Henan Province(23IRTSTHN009)Fund of Key Scientific Research Projects of Higher Education Institutions in Henan Province(22A150048)。
文摘By enhancing surface interaction between metal oxide particles and carbon-based materials,it can effectively improve Faraday capacitance and conductivity,ultimately achieving high energy density with sufficient redox reactions in supercapacitors.Through a gentle biomineralization process and subsequent thermal reduction strategy,we successfully prepared the graphene oxide(GO)wrapping mixed-valence manganese oxides(MnO_(x))and S,P self-codoped carbon matrix porous composite(MnO_(x)@SPC@reduced graphene oxide(RGO)).During the biomineralization process of engineered Pseudomonas sp.(Ml)cells,GO nanosheets functioned as the'soil'to adsorb Mn^(2+)ion and uniformly disperse biogenic Mn oxides(BMO).After undergoing annealing,the MnO_(x) nanoparticles were evenly wrapped with graphene,resulting in the creation of the MnO_(x)@SPC@RGO3 composite.This composite possesses strong C—O—Mn bond interfaces,numerous electroactive sites,and a uniform pore structure.By optimizing the synergistic interaction between the highly conductive graphene and the remarkable surface capacitance of MnO_(x),the MnO_(x)@SPC@RGO3 electrode,with its intercalation Faraday reactions mechanism of■transformations,exhibits an outstanding specific capacity(448.3 F·g^(-1)at 0.5 A·g^(-1)),multiplying performance(340.5 F·g^(-1)at10 A·g^(-1)),and cycling stability(93.8%retention after 5000 cycles).Moreover,the asymmetric all-solidstate supercapacitors of MnO_(x)@SPC@RGO3//PC exhibit an exceptional energy density of 64.8 W·h·kg^(-1)and power density of 350 W·kg^(-1),as well as a long lifespan with capacitance retention of 92.5%after10000 cycles.In conclusion,the synthetic route utilizing biomineralization and thermal reduction exhibits significant potential for exploiting high-performance electrode materials in all-solid-state supercapacitor applications.
基金supported by the SELECTVALUE project(2020-T1/AMB-19799,PI:J.J.L.)from the Community of Madrid,funded through the Talent Attraction Programfinancial support of the project RED2022-134552-T funded by MICIN/AEI/10.13039/501100011033financial support from“Comunidad de Madrid”to the project ADEMOSSBat(2022-T1/IND-23776)。
文摘Water scarcity,driven by climate change and population growth,necessitates innovative desalination technologies.Conventional methods for brackish water desalination are limited by high-energy demands,especially in the low salinity range,prompting the exploration of electrochemical approaches like faradaic deionization.Sodium-manganese oxides,traditionally used in sodium-ion batteries,show promise as faradaic deionization electrode materials due to their abundance,low toxicity,and cost-effectiveness.However,capacity fading during cycling,often caused by structural changes,volume expansion,or chemical transformations,remains a critical challenge.This study investigates the impact of morphology and crystal structure on the electrochemical performance of commercial and synthesized sodium-manganese oxides for faradaic deionization applications.Structural and electrochemical characterization in three-electrode cells with low-concentration electrolytes provided insights into the charge storage mechanisms.Rocking-chair full flow cell experiments demonstrated that the mixed-phase sodium-manganese oxide exhibited superior desalination performance,achieving a high salt removal capacity of 54.5 mg g^(−1)and a mean value in the salt removal rate of 1.49 mg g^(−1)min^(-1).Notably,mixed-phase sodium-manganese oxide maintained 98%capacity retention over 870 cycles,one of the longest reported cycling experiments in this field,effectively mitigating the Jahn-Teller effect.These findings highlight the crucial role of sodium-manganese oxide structure and morphology in electrochemical performance,positioning mixed-phase sodium-manganese oxide as a strong candidate for sustainable water treatment technologies.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 52074036 and 52404313)the Beijing Institute of Technology Teli Young Fellow Program。
文摘Spinel lithium manganese oxide(LiMn_(2)O_(4), LMO) emerges as a promising cathode material for future stationary energy storage applications due to its high voltage, safety, cost-effectiveness, and electrochemical performance. However,LMO suffers from rapid capacity degradation caused by the Jahn–Teller effect, Mn dissolution and side reactions. The mechanism remains unclear and even contradictory across various studies, impeding the advancement of high-performance LMO and its widespread utilization. In this study, 14 Ah commercial-level LMO batteries were manufactured and assessed.The mechanism of capacity attenuation in cycle-aged cells at room temperature(RT, 25℃) and high temperature(HT,55℃) storage cells was systematically investigated through the application of electrochemical quantitative methods. The results indicate specific capacity losses of approximately 6.26% and 2.55% for the cathodes in RT cycle-aged cells and HT storage cells, respectively, in comparison to fresh cells. These values are lower than the 12.54% and 6.99% capacity losses observed in RT cycle-aged cells and HT storage cells. While RT cycle-aging and HT storage conditions do not lead to irreversible capacity loss on the anode side. The results suggest that the primary causes of irreversible capacity degradation are not located on the cathode or anode. Nevertheless, significant polarization arises from the continuous growth of the solid electrolyte interphase(SEI), believed to be catalyzed by Mn deposited on the anode, which is considered harmful.This study elucidates that inhibiting the dissolution of Mn from the cathode, facilitating its transport in the electrolyte,promoting its deposition on the anode, and catalyzing the decomposition of the electrolyte are crucial factors for enhancing the performance of LMO batteries.
基金Project(2010FJ1011)supported by the Major Project of Hunan Science and Technology,ChinaProject(cstc2012ggB90002)supported by the Chongqing Key Science and Technology Program,China
文摘Manganese oxide ores from Gabon and Xiangxi were leached with waste tea as reductant in dilute sulfuric acid solution. The effects of waste tea dosage, concentration of sulfuric acid, liquid-to-solid ratio, leaching temperature and reaction time on leaching process were explored. The leaching efficiency of Gabonese manganese oxide ore reached almost 100% under the optimal condition which was determined as follows： manganese oxide ore to waste tea mass ratio of 10：1, sulfuric acid concentration of 2.5 molFL, liquid-to-solid ratio of 7.5：1, leaching temperature of 368 K, time of 8 h. The leaching efficiency of Xiangxi manganese oxide ore reached 99.8% under the optimal condition which was determined as follows： manganese oxide ore to waste tea mass ratio of 10：1, sulfuric acid concentration of 1.7 mol/L, liquid-to-solid ratio of 7.5：1, leaching temperature of 368 K, time of 8 h. The leaching process followed the internal diffusion controlled kinetic model, and the apparent activation energies of Gabonese manganese oxide ore and Xiangxi manganese oxide ore were calculated to be 38.2 kJ/mol and 20.4 kJ/mol, respectively. The morphological changes and mineralogical forms of the ore before and after the chemical treatment were discussed with the support of XRD analysis and SEM analysis.
基金supported by the National Natural Science Foundation of China(21325731,21221004 and 51478241)~~
文摘Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.
基金Project(21376273)supported by the National Natural Science Foundation of ChinaProject(2010FJ1011)supported by the Key Program of Science and Technology of Hunan Province,China
文摘The extraction of manganese from low-grade manganese oxide ores using Ca S derived from Ca SO4 as reductant was investigated. The effects of mass ratio of Ca S to ore, reduction temperature, reduction time, liquid to solid ratio（L/S ratio）, stirring speed, leaching temperature, leaching time and H2SO4 concentration on the leaching rates of Mn and Fe during the reduction–acid leaching process were discussed. The leaching rates of 96.47% for Mn and 19.24% for Fe were obtained under the optimized conditions of mass ratio of Ca S to manganese oxide ore 1：6.7, L/S ratio 5：1, stirring speed 300 r/min, reduction temperature of 95 °C for 2.0 h in the reduction process and leaching stirring speed of 200 r/min, H2SO4 concentration of 1.5 mol/L, leaching temperature of 80 °C for 5 min in the leaching process. In addition, this process can be employed in the recovery of manganese from various manganese oxide ores, and Mn leaching rate above 95% is obtained.
