In this paper, the method of relaxed boundary conditions is applied to rectangular plates with edges which are a sort of the mixture of simply supported portions and clamped portions, so that the lower limit of fundam...In this paper, the method of relaxed boundary conditions is applied to rectangular plates with edges which are a sort of the mixture of simply supported portions and clamped portions, so that the lower limit of fundamental frequency of such plates is evaluated. A kind of polynomial satisfying the displacement boundary conditions is designed, os that it is enabled to evaluate the upper limit of fundamental frequency by Ritz' method. The practical calculation examples solved by these methods have given satisfactory results. At the end of this paper, it is pointed out that the socalled exact solution of such plates usually evaluated by the force superposition method is essentially a kind of lower limit of solution, if the truncated error of series which occurs in actual calculation is considered.展开更多
To determine suitable thresholds for deficit irrigation of winter wheat in the well-irrigated area of the Huang-Huai-Hai Plain,we investigated the effects of different deficit irrigation lower limits and quotas on the...To determine suitable thresholds for deficit irrigation of winter wheat in the well-irrigated area of the Huang-Huai-Hai Plain,we investigated the effects of different deficit irrigation lower limits and quotas on the photosynthetic characteristics and grain yield of winter wheat.Four irrigation lower limits were set for initiating irrigation(i.e.,light drought(LD,50%,55%,60%and 50%of field holding capacity(FC)at the seedling-regreening,jointing,heading and filling-ripening stages,respectively),medium drought(MD,40%,50%,55%and 45%of FC at the same stages,respectively),adequate moisture(CK1,60%,65%,70%and 60%of FC at the same stages,respectively),heavy drought(CK2,35%,40%,45%and 40%of FC at the same stages,respectively))and five irrigation quota per event(30,60,90,120 and 180 mm)were set for each lower limit.We found that the increase of drought stress is conducive to normal photosynthesis of winter wheat leaves which is supported by the following findings.First,photosynthetic rate(Pn)of LD60 treatment was higher than that of LD30,LD90,LD120,LD180,MD30,MD60,MD90,MD120 and MD180.Then,Under the 90 mm irrigation quota treatment,the yield of winter wheat basically increased with the increase of irrigation’s lower limit.Moreover,With the increase in irrigation quota,the yield of winter wheat increased,and the water use efficiency(WUE)of winter wheat increased at first and then decreased.In addition,compared with the LD30,MD30,MD60,MD90,MD120,and MD180,the yield of winter wheat in LD60 treatment increased by about 3.23%(3-year average),32.3%,19.9%,11.7%,10.1%,and 14.6%.At the same time,the WUE with LD60 treatment of winter wheat was significantly higher than LD90,LD120,LD180,MD30,MD60,MD90,MD120,MD180 treatments.There was a positive correlation between soil volumetric water content and Pn and between yield and Pn.The key period for yield formation in winter wheat is 180 days after sowing.In conclusion,to achieve the dual goals of stable winter wheat yield and efficient utilization of water resources in this region,the suitable threshold for initiating deficit irrigation of winter wheat is the LD60 treatment.This conclusion provides data support for water-saving and stable yield of winter wheat in this area.展开更多
Testosterone(T)plays a crucial role in spermatogenesis because extremely low levels of intratesticular T lead to correspondingly low serum levels of total T(tT),severe disorders of spermatogenesis,and male sterility.H...Testosterone(T)plays a crucial role in spermatogenesis because extremely low levels of intratesticular T lead to correspondingly low serum levels of total T(tT),severe disorders of spermatogenesis,and male sterility.However,there is little consensus on the lower limits of serum tT in proven fertile men undergoing assisted reproductive technology treatments in Chinese or other Asian populations.We aimed to establish the reference range of serum tT based on a population of 868 fertile Chinese men undergoing in vitro fertilization or intracytoplasmic sperm injection and embryo transfer(IVF/ICSI-ET)treatments.We defined a fertile man as having had a live baby with his partner as recorded in our IVF registration system.The lower limits of serum tT were established using a Siemens IMMULITE 2000 chemiluminescent system.The 1st,2.5th,and 5th percentiles and their 95%confidence intervals(CIs)were 3.6(95%CI:2.7–4.1)nmol l−1,4.3(95%CI:4.1–5.0)nmol l−1,and 5.6(95%CI:4.8–5.8)nmol l−1,respectively.Using the linear correlation of serum tT between the Siemens platform and a liquid chromatography–tandem mass spectrometry platform,the calculated lower limits of serum tT were also established for fertile Chinese men undergoing IVF/ICSI-ET treatments,which will benefit the clinical diagnosis and treatment of male infertility during such procedures.展开更多
Here we present six key parameters that have been applied to evaluate the Silurian Longmaxi shale gas accumulations of southern Sichuan Province.These parameters include richness of organic matter,single layer shale t...Here we present six key parameters that have been applied to evaluate the Silurian Longmaxi shale gas accumulations of southern Sichuan Province.These parameters include richness of organic matter,single layer shale thickness,burial depth of the shale,maturity,shale properties,and brittle mineral content.In combination with drilling data,the lower limits of these six parameters for marine shale gas have been evaluated and the following conclusions are drawn:(1)Organic carbon recovery, gas content inversion,and production tests have been applied for the first time to measure the lower limit of TOC,which is determined to be 1.0%.(2)Based on the hydrocarbon generation and expulsion theory for source rocks and the characteristics of Longmaxi shale,the lower limit of the single-layer thickness is estimated to be 30 m,of which a thickness of at least 15 m should contain high-quality shale.(3)Based on the correlation of TOC and porosity,the lower limit of gas-filled porosity is 1.2%.(4)Other parameters,such as maturity,burial depth,and brittle mineral content have also been studied with regard to the geologic conditions of southern Sichuan.Based on the study results,an evaluation index system has been established for highly evolved marine shale gas,and the system has been applied successfully to geologically screened shale gas occurrences in southern Sichuan Province.展开更多
In this study, two rape varieties, ＂Zajiaolvbang＂ and ＂bilv＂, were used as experimental materials to investigate the effect of different lower irrigation limits （80%, 60%, 40% and 20% of field capacity） on quali...In this study, two rape varieties, ＂Zajiaolvbang＂ and ＂bilv＂, were used as experimental materials to investigate the effect of different lower irrigation limits （80%, 60%, 40% and 20% of field capacity） on quality of pet-grown rape. The results showed that contents of soluble sugar, soluble protein, vitamin C, nitrate and organic acids in rape all increased with the decreasing lower irrigation limit. Rape plants represented the best quality with lower irrigation limit of 60% of field capacity.展开更多
A feasible criterion was established to determine the lower size limit of raw coal(d_(pRm))for efficient beneficiation in the air-fluidized bed with magnetite particles.The feasibility of using small magnetite particl...A feasible criterion was established to determine the lower size limit of raw coal(d_(pRm))for efficient beneficiation in the air-fluidized bed with magnetite particles.The feasibility of using small magnetite particles to accommodate the fine raw coal was demonstrated from the experimental perspective.The minimum size for the magnetite particles to be fluidized smoothly was clarified as 47.1μm,which corresponded to the border between Geldart-B and-A groups.Since the gangue and coal components in the raw coal were crushed into the same size,d_(pRm)depended on the greater one between d_(pGm)(minimum size required for the gangue particles to sink towards the bottom)and d_(pCm)(minimum size required for the coal particles to float towards the top).dpcm was determined as 259μm by supposing that provided the gangue particles accumulated in the lower half bed,they could be potentially extracted from the bottom.On the other hand,it was observed that the coal particles could always accumulate in the upper half bed.Under such circumstances,dpcm was revealed as 9.8μm since finer coal particles would be blown out by air before the 47.1μm sized magnetite particles became fluidized.Eventually,dpRm was clarified as 259μm,agreeing with the common view that raw coal coarser than 6 mm could be effectively beneficiated in the air-fluidized bed with magnetite particles.Additionally,the difficulty in beneficiating the fine raw coal was revealed to arise more from the remixing of sorted gangue particles than that of separated coal particles.展开更多
Let x 1,x 2,… be independent identically distributed (i.i.d.) random variables, in which x n=0 or 1 and the probability of ｛x n=1｝ is p. Here p is unknown. Let τ be any finite stopping ...Let x 1,x 2,… be independent identically distributed (i.i.d.) random variables, in which x n=0 or 1 and the probability of ｛x n=1｝ is p. Here p is unknown. Let τ be any finite stopping time for (x n,n1). For any sequential sample (x 1,x 2,…,x τ ) and γ∈(0,1), we have given an optimal confidence limit of p with confidence level γ . Some related problems are also discussed.展开更多
The influence of explosive charge thickness on the quality of explosive welding of dissimilar metals was investigated.The lower limit law should be followed in the course of explosive welding.Three welding experiments...The influence of explosive charge thickness on the quality of explosive welding of dissimilar metals was investigated.The lower limit law should be followed in the course of explosive welding.Three welding experiments of stainless steel（410S）and steel（Q345R）were carried out in three different kinds of explosive charge thicknesses,namely 15,25and 35mm.Interfaces of morphology and mechanical properties of three samples were observed and tested.It was found that micro and small wavy bonding is mainly formed for charge thickness of 15mm whose strength is the highest with minor deformation and few defects in the interface;small and middle wavy bonding are mainly formed for charge thickness of 25 mm whose strength is comparatively mediocre;big wavy bonding is mainly formed for charge thickness of 35 mm whose strength is the lowest.The cause of high bonding strength of the micro and small wavy interface was analyzed and verified on the basis of the results of Electron Probe Micro-Analyzer（EPMA）tests of three selected samples.展开更多
On the basis of strict mathematical description about Failure_Free Period Life Test (FFPLT), the statistical properties of the tests and optimal confidence limit of the parameter are discussed in detail and correspond...On the basis of strict mathematical description about Failure_Free Period Life Test (FFPLT), the statistical properties of the tests and optimal confidence limit of the parameter are discussed in detail and corresponding calculating formulae are found out.展开更多
Based on the lower bound theorem of limit analysis, a solution procedure for limit analysis of three_dimensional elastoplastic structures was established using conventional boundary element method (BEM). The elastic s...Based on the lower bound theorem of limit analysis, a solution procedure for limit analysis of three_dimensional elastoplastic structures was established using conventional boundary element method (BEM). The elastic stress field for lower bound limit analysis was computed directly by three_dimensional boundary element method (3_D BEM). The self_equilibrium stress field was constructed by the linear combination of several self_equilibrium “basis vectors” which can be computed by elastic_plastic incremental iteration of 3_D BEM analysis. The lower bound limit analysis problem was finally reduced to a series of nonlinear programming sub_problems with relatively few optimal variables. The complex method was used to solve the nonlinear programming sub_problems. The numerical results show that the present solution procedure has good accuracy and high efficiency.展开更多
The finite dissolution model of silicon particles in the aluminum melt is built and calculated by the finite difference method, and the lower dissolution limit of silicon particles in the aluminum melt is proposed and...The finite dissolution model of silicon particles in the aluminum melt is built and calculated by the finite difference method, and the lower dissolution limit of silicon particles in the aluminum melt is proposed and verified by experiments, which could be the origin of microinhomogeneity in aluminum-silicon melts. When the effects of curvature and interface reaction on dissolution are not considered; the dissolution rate first decreases and later increases with time. When the effects of curvature and interface reaction on dissolution are considered, the dissolution rate first decreases and later increases when the interface reaction coefficient （k） is larger than 10 1, and the dissolution rate first decreases and later tends to be constant when k is smaller than 10-3. The dissolution is controlled by both diffusion and interface reaction when k is larger than 10-3, while the dissolution is controlled only by the interface reaction when k is smaller than 10-4.展开更多
Effectiveness and safety of a sports mouthguard depend on its thickness and material, and the thermoforming process affects these. The purpose of this study was to clarify the effects of differences in molding mechani...Effectiveness and safety of a sports mouthguard depend on its thickness and material, and the thermoforming process affects these. The purpose of this study was to clarify the effects of differences in molding mechanisms on the lower molding temperature limit and molding time in dental thermoforming. Ethylene vinyl acetate resin mouthguard sheet and two thermoforming machines;vacuum blower molding machine and vacuum ejector/pressure molding machine were used. The molding pressures for suction molding were −0.018 MPa for vacuum blower molding and −0.090 MPa for vacuum ejector molding, and for pressure molding was set to 0.090 MPa or 0.450 MPa. Based on the manufacturer’s standard molding temperature of 95˚C, the molding temperature was lowered in 2.5˚C increments to determine the lower molding temperature limit at which no molding defects occurred. In order to investigate the difference in molding time depending on the molding mechanism, the duration of molding pressure was adjusted in each molding machine, and the molding time required to obtain a sample without molding defects was measured. The molding time of each molding machine were compared using one-way analysis of variance. The lower molding temperature limit was 90.0˚C for the vacuum blower machine, 77.5˚C for the vacuum ejector machine, 77.5˚C for the pressure molding machine at 0.090 MPa, and 67.5˚C for the pressure molding machine at 0.45 MPa. The lower molding temperature limit was higher for lower absolute values of molding pressure. The molding time was shorter for pressure molding than for suction molding. Significant differences were observed between all conditions except between the pressure molding machine at 0.090 MPa and 0.45 MPa (P < 0.01). A comparison of the differences in lower molding temperature limit and molding time due to molding mechanisms in dental thermoforming revealed that the lower molding temperature limit depends on the molding pressure and that the molding time is longer for suction molding than for pressure molding.展开更多
Using the characteristic of addition of information quantity and the principle of equivalence of information quantity, this paper derives the general conversion formulae of the formation theory method conversion (synt...Using the characteristic of addition of information quantity and the principle of equivalence of information quantity, this paper derives the general conversion formulae of the formation theory method conversion (synthesis) on the systems consisting of different success failure model units. According to the fundamental method of the unit reliability assessment, the general models of system reliability approximate lower limits are given. Finally, this paper analyses the application of the assessment method by examples, the assessment results are neither conservative nor radical and very satisfactory. The assessment method can be popularized to the systems which have fixed reliability structural models.展开更多
A method of localization is proposed to lower the high order of equations in FEM calcula- tion for the stability of a complex thin-walled structure.The localized analysis enables us to obtain both the upper and lower ...A method of localization is proposed to lower the high order of equations in FEM calcula- tion for the stability of a complex thin-walled structure.The localized analysis enables us to obtain both the upper and lower limits for the bifurcating point in a whole linear elastic structural system,as well as an ap- proximate solution to asymptotic post-buckling problem.Some numerical examples are included.展开更多
In nature, many physical phenomena follow the least-action principle, which is also abided by the course of explosive welding of stainless steel/steel. The optimal welding interface can be obtained with the least expl...In nature, many physical phenomena follow the least-action principle, which is also abided by the course of explosive welding of stainless steel/steel. The optimal welding interface can be obtained with the least explosive charge by theoretical analysis and interface test. The bonding energy can be acknowledged as the ＂action＂ in explosive welding. To minimize the bonding energy, these rules must be followed such as the lower limit of explosive charge, the upper limit of span and the explosive of critical explosion velocity. The principle of least-action is achieved in the course of explosive welding, and the interface will be optimum.展开更多
This study proposes an equivalent-elevation method to evaluate the integrated effects of latitude and elevation on regional and local-scale permafrost distribution in the Qinghai-Tibet Plateau,and to model the general...This study proposes an equivalent-elevation method to evaluate the integrated effects of latitude and elevation on regional and local-scale permafrost distribution in the Qinghai-Tibet Plateau,and to model the general permafrost-distribution patterns in regional and local-scale area.It is found that the Gaussian curve―an empirical model describing the relation between variations of altitudinal permafrost lower limit (PLL) and latitude in the Northern Hemisphere―could be applied in regional-and local-scale areas in the Qinghai-Tibet Plateau in a latitude-sensitive interval of 30°-50°N.The curve was then used to evaluate the latitudinal effect on permafrost distribution through transforming the latitudinal effect into a kind of altitudinal difference of PLL.This study then calculated the local equivalent-elevation value by overlaying the altitudinal difference of PLL onto real elevation at a certain location.The equivalent-elevation method was verified in an experimental subwatershed of the Qinghai-Tibet Plateau.However,feasibility of the method should be further tested in order to extend for future studies.The use of equivalent-elevation values can build a platform for comparing the regional general permafrost distribution in the plateau,and for basing further evaluations of local factors' effects on regional permafrost distribution.展开更多
The differences in organic matter abundance and rock composition between shale and mudstone determine the discrepancy of their contributions to the formation of conventional and shale oil/gas reservoirs.The evaluation...The differences in organic matter abundance and rock composition between shale and mudstone determine the discrepancy of their contributions to the formation of conventional and shale oil/gas reservoirs.The evaluation criteria of source rocks are different in the future exploration in self-sourced petroleum systems.Shales are deposited in deep/semi-deep lacustrine,with low sedimentation rate and chemical depositions of various degrees,while mudstones are mostly formed in shallow lacustrine/lakeside,with high deposition rate and density flow characteristics.Three factors contribute to the enrichment of organic matter in shales,including the"fertility effect"caused by volcanic ash deposition and hydrothermal injection,excessive and over-speed growth of organisms promoted by radioactive materials,and deep-water anaerobic environment and low sedimentation rate to protect the accumulation of organic matter from dilution.Lamellations in shales are easy to be stripped into storage space,and acid water produced during hydrocarbon generation can dissolve some particles to generate new pores.The massive mudstones with high clay content are of poor matrix porosity.Shales with high total organic carbon,developed laminations,relatively good reservoir property,and high brittle mineral content,are the most favorable lithofacies for shale oil exploration and development.It is necessary to conduct investigation on the differences between shale and mudstone reservoirs,to identify resources distribution in shale and mudstone formations,determine the type and standard of"sweet-spot"evaluation parameters,optimize"sweet-spot areas/sections",and adopt effective development technologies,which is of great significance to objectively evaluate the total amount and economy of shale oil resources,as well as the scale of effective exploitation.展开更多
Jack-up platforms of the Ocean engineering structures always withstand the vertical gravity loads which are applied to the seabed by spudcan, so it is important to determine the bearing capacity and the penetration de...Jack-up platforms of the Ocean engineering structures always withstand the vertical gravity loads which are applied to the seabed by spudcan, so it is important to determine the bearing capacity and the penetration depth of the spudcan for its geometry. In fact, it is up to the deformation law and the failure modes of soil surrounding the spudcan which can calculate the ultimate bearing capacity of the spudcan foundation on the soil seabed. By using the finite element analysis software Abaqus, the deformation law of soil around the spudcan is analyzed in detail, and the failure modes of soil surrounding the spudcan foundation are achieved. At the same time, based on the limit equilibrium theory, by use of static permissible slip-line field, the ultimate bearing capacity of the spudcan foundation is analyzed and the lower limit solution is derived theoretically, and the effect of the spudcan angle on the ultimate bearing capacity is investigated. The numerical results are compared with those obtained by the theoretical formulas deduced in this paper. On the basis of the lower limit solutions in this paper, the effect of the spudcan angle on the ultimate bearing capacity is revealed, and a practical bearing capacity formula is given to take the effect of the spudcan angle into consideration.展开更多
The log-Weibull distribution is a variant of the three-parameter Weibull distribution. The probability plot of a distribution model is desired since it can help to decide on whether the model is appropriate for fittin...The log-Weibull distribution is a variant of the three-parameter Weibull distribution. The probability plot of a distribution model is desired since it can help to decide on whether the model is appropriate for fitting a given dataset and can provide the initial estimate of the model parameters. The decision on the appropriateness of a distribution is somehow subjective. This paper presents a probability plot of the log-Weibull distribution(LWPP). The distribution of the probability plot correlation coefficient is studied. From this distribution, a lower confidence limit is determined for determining whether the probability plot correlation coefficient derived from a given data set is large enough. The appropriateness and usefulness of this study are illustrated by two real-world examples.展开更多
Estimation of the plant-available water capacity(PAWC)of soils at a regional scale helps in adopting better land use planning,developing suitable irrigation schedules for crops,and optimizing the use of scarce water r...Estimation of the plant-available water capacity(PAWC)of soils at a regional scale helps in adopting better land use planning,developing suitable irrigation schedules for crops,and optimizing the use of scarce water resources.In the current study,72 soil profiles were sampled from the Barossa region of South Australia to estimate pedo-transfer functions deduced from easily estimated soil properties.These functions were then used to estimate the fixed(10 and 33 kPa)and dynamic pressure head(h_(fc))water contents at field capacity(FC)for minimum drainage flux(0.01 and 0.001 cm d^(-1)),which serves as the upper boundary for plant-available water in soils.The estimated residual water content was corrected for subsoil constraints,especially the exchangeable sodium percentage(ESP).The results showed that the mean values of h_(fc)in sand-dominated light and medium textured soils(i.e.,sand,loamy sand,sandy loam,and loam)varied in a narrow range(15.8-18.2 kPa),whereas those in the clay-dominated heavy textured soils(i.e.,clay loam)showed a wide range(11.3-49.3 kPa).There were large differences in PAWC for dynamic FC(PAWC_(fc))and fixed FC at 10 kPa(PAWC10),33 kPa(PAWC33),and a mix of 10and 33 kPa(PAWC_(10,33))pressure heads depending on soil texture.Normally,the difference between PAWC at 10 kPa and h_(fc)(ΔPAWC_(10))was positive,whereas that between 33 kPa and h_(fc)(ΔPAWC_(33))was negative across all sites.Nevertheless,the estimation of PAWC assuming a fixed FC at 10 and 33 kPa pressures(i.e.,PAWC_(10,33))for sandy,clay,and silty soils reduced the difference between fixed and dynamic pressure PAWCs to<10%across the region.The estimation of PAWC was improved by incorporating the impact of subsoil constraints,such as high ESP,which was more pronounced for clay and silty soils.These findings demonstrate the inherent inconsistencies between static pressure and flux-based dynamic FC estimations in soils.Soil heterogeneity,intra-texture variability,subsoil constraints,and swell-shrink clays can have great impacts on the water retention capacity in response to dynamic and fixed pressure FC values.展开更多
文摘In this paper, the method of relaxed boundary conditions is applied to rectangular plates with edges which are a sort of the mixture of simply supported portions and clamped portions, so that the lower limit of fundamental frequency of such plates is evaluated. A kind of polynomial satisfying the displacement boundary conditions is designed, os that it is enabled to evaluate the upper limit of fundamental frequency by Ritz' method. The practical calculation examples solved by these methods have given satisfactory results. At the end of this paper, it is pointed out that the socalled exact solution of such plates usually evaluated by the force superposition method is essentially a kind of lower limit of solution, if the truncated error of series which occurs in actual calculation is considered.
基金supported jointly by the Natural Science Foundation of China (No.41807041)the Ninth Batch of Key Disciplines in Henan Province—Mechanical Design,Manufacturing and Automation (JG[2018]No.119).
文摘To determine suitable thresholds for deficit irrigation of winter wheat in the well-irrigated area of the Huang-Huai-Hai Plain,we investigated the effects of different deficit irrigation lower limits and quotas on the photosynthetic characteristics and grain yield of winter wheat.Four irrigation lower limits were set for initiating irrigation(i.e.,light drought(LD,50%,55%,60%and 50%of field holding capacity(FC)at the seedling-regreening,jointing,heading and filling-ripening stages,respectively),medium drought(MD,40%,50%,55%and 45%of FC at the same stages,respectively),adequate moisture(CK1,60%,65%,70%and 60%of FC at the same stages,respectively),heavy drought(CK2,35%,40%,45%and 40%of FC at the same stages,respectively))and five irrigation quota per event(30,60,90,120 and 180 mm)were set for each lower limit.We found that the increase of drought stress is conducive to normal photosynthesis of winter wheat leaves which is supported by the following findings.First,photosynthetic rate(Pn)of LD60 treatment was higher than that of LD30,LD90,LD120,LD180,MD30,MD60,MD90,MD120 and MD180.Then,Under the 90 mm irrigation quota treatment,the yield of winter wheat basically increased with the increase of irrigation’s lower limit.Moreover,With the increase in irrigation quota,the yield of winter wheat increased,and the water use efficiency(WUE)of winter wheat increased at first and then decreased.In addition,compared with the LD30,MD30,MD60,MD90,MD120,and MD180,the yield of winter wheat in LD60 treatment increased by about 3.23%(3-year average),32.3%,19.9%,11.7%,10.1%,and 14.6%.At the same time,the WUE with LD60 treatment of winter wheat was significantly higher than LD90,LD120,LD180,MD30,MD60,MD90,MD120,MD180 treatments.There was a positive correlation between soil volumetric water content and Pn and between yield and Pn.The key period for yield formation in winter wheat is 180 days after sowing.In conclusion,to achieve the dual goals of stable winter wheat yield and efficient utilization of water resources in this region,the suitable threshold for initiating deficit irrigation of winter wheat is the LD60 treatment.This conclusion provides data support for water-saving and stable yield of winter wheat in this area.
基金the National Key Research and Development Program of China(No.2016YFC1000201,No.2018YFC1002104,No.2018YFC1002106,and No.2016YFC1000302)the National Natural Science Foundation of China(No.81300373,and No.81771650)+2 种基金the Capital Health Research and Development of Special Projects(No.2018-1-4091)the Program for Innovative Research Team of Yunnan,China(No.2017HC009)the Major National R&D Projects of China(No.2017ZX09304012-012).
文摘Testosterone(T)plays a crucial role in spermatogenesis because extremely low levels of intratesticular T lead to correspondingly low serum levels of total T(tT),severe disorders of spermatogenesis,and male sterility.However,there is little consensus on the lower limits of serum tT in proven fertile men undergoing assisted reproductive technology treatments in Chinese or other Asian populations.We aimed to establish the reference range of serum tT based on a population of 868 fertile Chinese men undergoing in vitro fertilization or intracytoplasmic sperm injection and embryo transfer(IVF/ICSI-ET)treatments.We defined a fertile man as having had a live baby with his partner as recorded in our IVF registration system.The lower limits of serum tT were established using a Siemens IMMULITE 2000 chemiluminescent system.The 1st,2.5th,and 5th percentiles and their 95%confidence intervals(CIs)were 3.6(95%CI:2.7–4.1)nmol l−1,4.3(95%CI:4.1–5.0)nmol l−1,and 5.6(95%CI:4.8–5.8)nmol l−1,respectively.Using the linear correlation of serum tT between the Siemens platform and a liquid chromatography–tandem mass spectrometry platform,the calculated lower limits of serum tT were also established for fertile Chinese men undergoing IVF/ICSI-ET treatments,which will benefit the clinical diagnosis and treatment of male infertility during such procedures.
基金supported by National Science Foundation for Distinguished Young Scholars of China(Grant No.51125019)
文摘Here we present six key parameters that have been applied to evaluate the Silurian Longmaxi shale gas accumulations of southern Sichuan Province.These parameters include richness of organic matter,single layer shale thickness,burial depth of the shale,maturity,shale properties,and brittle mineral content.In combination with drilling data,the lower limits of these six parameters for marine shale gas have been evaluated and the following conclusions are drawn:(1)Organic carbon recovery, gas content inversion,and production tests have been applied for the first time to measure the lower limit of TOC,which is determined to be 1.0%.(2)Based on the hydrocarbon generation and expulsion theory for source rocks and the characteristics of Longmaxi shale,the lower limit of the single-layer thickness is estimated to be 30 m,of which a thickness of at least 15 m should contain high-quality shale.(3)Based on the correlation of TOC and porosity,the lower limit of gas-filled porosity is 1.2%.(4)Other parameters,such as maturity,burial depth,and brittle mineral content have also been studied with regard to the geologic conditions of southern Sichuan.Based on the study results,an evaluation index system has been established for highly evolved marine shale gas,and the system has been applied successfully to geologically screened shale gas occurrences in southern Sichuan Province.
基金Supported by Project of Modern Agricultural Industry Technology System of Jilin Province-Research and Demonstration of High-efficiency Production Technology for Protected VegetablesSpecial Fund for Breeding of Jilin Province Department of Finance(201104)
文摘In this study, two rape varieties, ＂Zajiaolvbang＂ and ＂bilv＂, were used as experimental materials to investigate the effect of different lower irrigation limits （80%, 60%, 40% and 20% of field capacity） on quality of pet-grown rape. The results showed that contents of soluble sugar, soluble protein, vitamin C, nitrate and organic acids in rape all increased with the decreasing lower irrigation limit. Rape plants represented the best quality with lower irrigation limit of 60% of field capacity.
基金supported by Shandong Provincial Natural Science Foundation(ZR2023MB038)Youth Innovation Team Program of Shandong Higher Education Institution(2022KJ156)。
文摘A feasible criterion was established to determine the lower size limit of raw coal(d_(pRm))for efficient beneficiation in the air-fluidized bed with magnetite particles.The feasibility of using small magnetite particles to accommodate the fine raw coal was demonstrated from the experimental perspective.The minimum size for the magnetite particles to be fluidized smoothly was clarified as 47.1μm,which corresponded to the border between Geldart-B and-A groups.Since the gangue and coal components in the raw coal were crushed into the same size,d_(pRm)depended on the greater one between d_(pGm)(minimum size required for the gangue particles to sink towards the bottom)and d_(pCm)(minimum size required for the coal particles to float towards the top).dpcm was determined as 259μm by supposing that provided the gangue particles accumulated in the lower half bed,they could be potentially extracted from the bottom.On the other hand,it was observed that the coal particles could always accumulate in the upper half bed.Under such circumstances,dpcm was revealed as 9.8μm since finer coal particles would be blown out by air before the 47.1μm sized magnetite particles became fluidized.Eventually,dpRm was clarified as 259μm,agreeing with the common view that raw coal coarser than 6 mm could be effectively beneficiated in the air-fluidized bed with magnetite particles.Additionally,the difficulty in beneficiating the fine raw coal was revealed to arise more from the remixing of sorted gangue particles than that of separated coal particles.
文摘Let x 1,x 2,… be independent identically distributed (i.i.d.) random variables, in which x n=0 or 1 and the probability of ｛x n=1｝ is p. Here p is unknown. Let τ be any finite stopping time for (x n,n1). For any sequential sample (x 1,x 2,…,x τ ) and γ∈(0,1), we have given an optimal confidence limit of p with confidence level γ . Some related problems are also discussed.
基金supported by the National Natural Science Foundation of China(No.51541112)Special Fund Achievement Transformation Projects in Jiangsu(No.BA2012030)
文摘The influence of explosive charge thickness on the quality of explosive welding of dissimilar metals was investigated.The lower limit law should be followed in the course of explosive welding.Three welding experiments of stainless steel（410S）and steel（Q345R）were carried out in three different kinds of explosive charge thicknesses,namely 15,25and 35mm.Interfaces of morphology and mechanical properties of three samples were observed and tested.It was found that micro and small wavy bonding is mainly formed for charge thickness of 15mm whose strength is the highest with minor deformation and few defects in the interface;small and middle wavy bonding are mainly formed for charge thickness of 25 mm whose strength is comparatively mediocre;big wavy bonding is mainly formed for charge thickness of 35 mm whose strength is the lowest.The cause of high bonding strength of the micro and small wavy interface was analyzed and verified on the basis of the results of Electron Probe Micro-Analyzer（EPMA）tests of three selected samples.
文摘On the basis of strict mathematical description about Failure_Free Period Life Test (FFPLT), the statistical properties of the tests and optimal confidence limit of the parameter are discussed in detail and corresponding calculating formulae are found out.
文摘Based on the lower bound theorem of limit analysis, a solution procedure for limit analysis of three_dimensional elastoplastic structures was established using conventional boundary element method (BEM). The elastic stress field for lower bound limit analysis was computed directly by three_dimensional boundary element method (3_D BEM). The self_equilibrium stress field was constructed by the linear combination of several self_equilibrium “basis vectors” which can be computed by elastic_plastic incremental iteration of 3_D BEM analysis. The lower bound limit analysis problem was finally reduced to a series of nonlinear programming sub_problems with relatively few optimal variables. The complex method was used to solve the nonlinear programming sub_problems. The numerical results show that the present solution procedure has good accuracy and high efficiency.
基金supported by the National Basic Research Program of China(Grant No.2013CB632203)
文摘The finite dissolution model of silicon particles in the aluminum melt is built and calculated by the finite difference method, and the lower dissolution limit of silicon particles in the aluminum melt is proposed and verified by experiments, which could be the origin of microinhomogeneity in aluminum-silicon melts. When the effects of curvature and interface reaction on dissolution are not considered; the dissolution rate first decreases and later increases with time. When the effects of curvature and interface reaction on dissolution are considered, the dissolution rate first decreases and later increases when the interface reaction coefficient （k） is larger than 10 1, and the dissolution rate first decreases and later tends to be constant when k is smaller than 10-3. The dissolution is controlled by both diffusion and interface reaction when k is larger than 10-3, while the dissolution is controlled only by the interface reaction when k is smaller than 10-4.
文摘Effectiveness and safety of a sports mouthguard depend on its thickness and material, and the thermoforming process affects these. The purpose of this study was to clarify the effects of differences in molding mechanisms on the lower molding temperature limit and molding time in dental thermoforming. Ethylene vinyl acetate resin mouthguard sheet and two thermoforming machines;vacuum blower molding machine and vacuum ejector/pressure molding machine were used. The molding pressures for suction molding were −0.018 MPa for vacuum blower molding and −0.090 MPa for vacuum ejector molding, and for pressure molding was set to 0.090 MPa or 0.450 MPa. Based on the manufacturer’s standard molding temperature of 95˚C, the molding temperature was lowered in 2.5˚C increments to determine the lower molding temperature limit at which no molding defects occurred. In order to investigate the difference in molding time depending on the molding mechanism, the duration of molding pressure was adjusted in each molding machine, and the molding time required to obtain a sample without molding defects was measured. The molding time of each molding machine were compared using one-way analysis of variance. The lower molding temperature limit was 90.0˚C for the vacuum blower machine, 77.5˚C for the vacuum ejector machine, 77.5˚C for the pressure molding machine at 0.090 MPa, and 67.5˚C for the pressure molding machine at 0.45 MPa. The lower molding temperature limit was higher for lower absolute values of molding pressure. The molding time was shorter for pressure molding than for suction molding. Significant differences were observed between all conditions except between the pressure molding machine at 0.090 MPa and 0.45 MPa (P < 0.01). A comparison of the differences in lower molding temperature limit and molding time due to molding mechanisms in dental thermoforming revealed that the lower molding temperature limit depends on the molding pressure and that the molding time is longer for suction molding than for pressure molding.
文摘Using the characteristic of addition of information quantity and the principle of equivalence of information quantity, this paper derives the general conversion formulae of the formation theory method conversion (synthesis) on the systems consisting of different success failure model units. According to the fundamental method of the unit reliability assessment, the general models of system reliability approximate lower limits are given. Finally, this paper analyses the application of the assessment method by examples, the assessment results are neither conservative nor radical and very satisfactory. The assessment method can be popularized to the systems which have fixed reliability structural models.
基金Project supported by National Natural Science Foundation of China
文摘A method of localization is proposed to lower the high order of equations in FEM calcula- tion for the stability of a complex thin-walled structure.The localized analysis enables us to obtain both the upper and lower limits for the bifurcating point in a whole linear elastic structural system,as well as an ap- proximate solution to asymptotic post-buckling problem.Some numerical examples are included.
基金Sponsored by Jiangsu Provincial Foundation of Technology Achievement Transform of China(BA2012030)
文摘In nature, many physical phenomena follow the least-action principle, which is also abided by the course of explosive welding of stainless steel/steel. The optimal welding interface can be obtained with the least explosive charge by theoretical analysis and interface test. The bonding energy can be acknowledged as the ＂action＂ in explosive welding. To minimize the bonding energy, these rules must be followed such as the lower limit of explosive charge, the upper limit of span and the explosive of critical explosion velocity. The principle of least-action is achieved in the course of explosive welding, and the interface will be optimum.
基金Under the auspices of Major State Basic Research Development Program of China(No.2010CB951402)National Natural Science Foundation of China(No.41101067)+1 种基金Foundation for Excellent Youth Scholars of Cold and Arid Regions Environmental and Engineering Research Institute,Chinese Academy of Sciences(No.Y184A91001)Research Program of State Key Laboratory of Frozen Soil Engineering of Cold and Arid Regions Environmental and Engineering Research Institute,Chinese Academy of Sciences(No.SKLFSE-ZQ-10)
文摘This study proposes an equivalent-elevation method to evaluate the integrated effects of latitude and elevation on regional and local-scale permafrost distribution in the Qinghai-Tibet Plateau,and to model the general permafrost-distribution patterns in regional and local-scale area.It is found that the Gaussian curve―an empirical model describing the relation between variations of altitudinal permafrost lower limit (PLL) and latitude in the Northern Hemisphere―could be applied in regional-and local-scale areas in the Qinghai-Tibet Plateau in a latitude-sensitive interval of 30°-50°N.The curve was then used to evaluate the latitudinal effect on permafrost distribution through transforming the latitudinal effect into a kind of altitudinal difference of PLL.This study then calculated the local equivalent-elevation value by overlaying the altitudinal difference of PLL onto real elevation at a certain location.The equivalent-elevation method was verified in an experimental subwatershed of the Qinghai-Tibet Plateau.However,feasibility of the method should be further tested in order to extend for future studies.The use of equivalent-elevation values can build a platform for comparing the regional general permafrost distribution in the plateau,and for basing further evaluations of local factors' effects on regional permafrost distribution.
基金Supported by the China National Science and Technology Major Project(2016ZX05046,2017ZX05001)
文摘The differences in organic matter abundance and rock composition between shale and mudstone determine the discrepancy of their contributions to the formation of conventional and shale oil/gas reservoirs.The evaluation criteria of source rocks are different in the future exploration in self-sourced petroleum systems.Shales are deposited in deep/semi-deep lacustrine,with low sedimentation rate and chemical depositions of various degrees,while mudstones are mostly formed in shallow lacustrine/lakeside,with high deposition rate and density flow characteristics.Three factors contribute to the enrichment of organic matter in shales,including the"fertility effect"caused by volcanic ash deposition and hydrothermal injection,excessive and over-speed growth of organisms promoted by radioactive materials,and deep-water anaerobic environment and low sedimentation rate to protect the accumulation of organic matter from dilution.Lamellations in shales are easy to be stripped into storage space,and acid water produced during hydrocarbon generation can dissolve some particles to generate new pores.The massive mudstones with high clay content are of poor matrix porosity.Shales with high total organic carbon,developed laminations,relatively good reservoir property,and high brittle mineral content,are the most favorable lithofacies for shale oil exploration and development.It is necessary to conduct investigation on the differences between shale and mudstone reservoirs,to identify resources distribution in shale and mudstone formations,determine the type and standard of"sweet-spot"evaluation parameters,optimize"sweet-spot areas/sections",and adopt effective development technologies,which is of great significance to objectively evaluate the total amount and economy of shale oil resources,as well as the scale of effective exploitation.
基金financially supported by the National Natural Science Foundation of China(Grant No.51679224)
文摘Jack-up platforms of the Ocean engineering structures always withstand the vertical gravity loads which are applied to the seabed by spudcan, so it is important to determine the bearing capacity and the penetration depth of the spudcan for its geometry. In fact, it is up to the deformation law and the failure modes of soil surrounding the spudcan which can calculate the ultimate bearing capacity of the spudcan foundation on the soil seabed. By using the finite element analysis software Abaqus, the deformation law of soil around the spudcan is analyzed in detail, and the failure modes of soil surrounding the spudcan foundation are achieved. At the same time, based on the limit equilibrium theory, by use of static permissible slip-line field, the ultimate bearing capacity of the spudcan foundation is analyzed and the lower limit solution is derived theoretically, and the effect of the spudcan angle on the ultimate bearing capacity is investigated. The numerical results are compared with those obtained by the theoretical formulas deduced in this paper. On the basis of the lower limit solutions in this paper, the effect of the spudcan angle on the ultimate bearing capacity is revealed, and a practical bearing capacity formula is given to take the effect of the spudcan angle into consideration.
基金the National Natural Science Foundation of China(No.71371035)
文摘The log-Weibull distribution is a variant of the three-parameter Weibull distribution. The probability plot of a distribution model is desired since it can help to decide on whether the model is appropriate for fitting a given dataset and can provide the initial estimate of the model parameters. The decision on the appropriateness of a distribution is somehow subjective. This paper presents a probability plot of the log-Weibull distribution(LWPP). The distribution of the probability plot correlation coefficient is studied. From this distribution, a lower confidence limit is determined for determining whether the probability plot correlation coefficient derived from a given data set is large enough. The appropriateness and usefulness of this study are illustrated by two real-world examples.
文摘Estimation of the plant-available water capacity(PAWC)of soils at a regional scale helps in adopting better land use planning,developing suitable irrigation schedules for crops,and optimizing the use of scarce water resources.In the current study,72 soil profiles were sampled from the Barossa region of South Australia to estimate pedo-transfer functions deduced from easily estimated soil properties.These functions were then used to estimate the fixed(10 and 33 kPa)and dynamic pressure head(h_(fc))water contents at field capacity(FC)for minimum drainage flux(0.01 and 0.001 cm d^(-1)),which serves as the upper boundary for plant-available water in soils.The estimated residual water content was corrected for subsoil constraints,especially the exchangeable sodium percentage(ESP).The results showed that the mean values of h_(fc)in sand-dominated light and medium textured soils(i.e.,sand,loamy sand,sandy loam,and loam)varied in a narrow range(15.8-18.2 kPa),whereas those in the clay-dominated heavy textured soils(i.e.,clay loam)showed a wide range(11.3-49.3 kPa).There were large differences in PAWC for dynamic FC(PAWC_(fc))and fixed FC at 10 kPa(PAWC10),33 kPa(PAWC33),and a mix of 10and 33 kPa(PAWC_(10,33))pressure heads depending on soil texture.Normally,the difference between PAWC at 10 kPa and h_(fc)(ΔPAWC_(10))was positive,whereas that between 33 kPa and h_(fc)(ΔPAWC_(33))was negative across all sites.Nevertheless,the estimation of PAWC assuming a fixed FC at 10 and 33 kPa pressures(i.e.,PAWC_(10,33))for sandy,clay,and silty soils reduced the difference between fixed and dynamic pressure PAWCs to<10%across the region.The estimation of PAWC was improved by incorporating the impact of subsoil constraints,such as high ESP,which was more pronounced for clay and silty soils.These findings demonstrate the inherent inconsistencies between static pressure and flux-based dynamic FC estimations in soils.Soil heterogeneity,intra-texture variability,subsoil constraints,and swell-shrink clays can have great impacts on the water retention capacity in response to dynamic and fixed pressure FC values.
