Basicity has an important effect on the sinter quality, especially for low-titanium vanadium-titanium sinter. The effect of basieity on sintering behavior of low-titanium vanadium-titanium mixture, and the transferenc...Basicity has an important effect on the sinter quality, especially for low-titanium vanadium-titanium sinter. The effect of basieity on sintering behavior of low-titanium vanadium-titanium mixture, and the transference and distribution of element in sintering process were researched by sinter pot test, mineralogical analysis, scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS） analysis. The results show that CaO preferentially reacts with TiO2, generating pervoskite, so that the total liquid phase content of the sinter is low. There is an increase in the perovskite concentration of the sinter with the basicity ranging from 1.9：1 to 2.7：1. With increasing the basicity, the calcium ferrite content increases slightly and then rises rapidly, while the silicate content decreases and the metallurgical property of the sinter is improved. As for the distribution of these elements in the sinter, Ti occurs mainly in perovskite, V occurs mainly in silicate, and Fe occurs mainly in magnetite and hematite. The most abundant occurrence of Ca and Si occurs in silicate and perovskite. With increasing the basicity, the contents of A1 and Mg increase in calcium ferrite, while they decrease in other minerals.展开更多
The wear resistance of six kinds of the electrolytic low-titanium eutectic AI-Si piston alloys with various Ti content ranging from 0.00wt.% to 0.21wt.% has been studied. A new method of adding Ti is adopted in the el...The wear resistance of six kinds of the electrolytic low-titanium eutectic AI-Si piston alloys with various Ti content ranging from 0.00wt.% to 0.21wt.% has been studied. A new method of adding Ti is adopted in the electrolytic low-titanium aluminum alloy ingots. The electrolytic low-titanium eutectic AI-Si piston alloys are produced by remelting the electrolytic low-titanium aluminum alloy, crystal silicon, pure magnesium, AI-50%Cu and AI-10%Mn master alloy. The wear experiments are conducted using MM200 wear testing machine under lubricating condition. The results indicate that the better wear resistance and the less weight loss are achieved in the study for the eutectic AI-Si piston alloys with 0.08wt.%-0.12wt.% Ti content. The highest ultimate tensile strength of 135.94 MPa at 300℃ and HV141.70 hardness of the alloys are obtained at 0.12wt.% and 0.08wt.% Ti content, respectively. The wear mechanism of the eutectic AI-Si piston alloys under lubricating condition is abrasive wear.展开更多
The effects of superheating temperature on the grain refining efficiency of Ti existing in electrolytic low-titanium aluminum(ELTA)without and with the Al-4B addition and the Al-5Ti-1B master alloy in pure Al were com...The effects of superheating temperature on the grain refining efficiency of Ti existing in electrolytic low-titanium aluminum(ELTA)without and with the Al-4B addition and the Al-5Ti-1B master alloy in pure Al were comparatively investigated. The results show that the Ti existing in ELTA without Al-4B addition exhibits a certain grain refining efficiency when the melt superheating temperature is lower,but the efficiency decreases rapidly when the superheating temperature is higher.The grain refining efficiency of the Al-5Ti-1B master alloy is better than that of the Ti existing in ELTA without Al-4B addition at any superheating temperature,but it also decreases obviously with the increase of the superheating temperature.One important reason is that the TiB2 particles coming from the Al-5Ti-1B master alloy can settle down at the bottom of the Al melt easily when the superheating temperature is increased,thus decrease the number of the potent heterogeneous nuclei retained in the Al melt.If the Al-4B master alloy is added to the ELTA melt,the grain refining efficiency of the Ti existing in ELTA can be improved significantly, and does not decrease with the increase of the superheating temperature.This perhaps provides us a possible method to suppress the effect of the superheated melt on the microstructures of aluminum..展开更多
The low-cycle fatigue (LCF) behavior of two kinds of A356 alloys produced by different titanium alloying methods was investigated and compared. The effect of titanium content and titanium alloying methods on LCF behav...The low-cycle fatigue (LCF) behavior of two kinds of A356 alloys produced by different titanium alloying methods was investigated and compared. The effect of titanium content and titanium alloying methods on LCF behavior is analyzed with plastic strain energy density. The results show that all alloys exhibit the cyclic hardening behavior. Raising Ti content can obviously increase the cyclic hardening ability. But the effect of Ti alloying method isn't distinct. Whether for the EA356 alloys or for MA356 alloys, the alloys with low titanium content have longer low-cycle fatigue life than that of the alloys with high titanium content. This is because that the alloys with low titanium content can consume higher cyclic plastic strain energy during cyclic deformation compared with alloys with high titanium content.展开更多
基金Projects(2012AA062302,2012AA062304) supported by the National High Technology Research and Development Program of China(863 Program)Projects(51090384,51174051) supported by the National Natural Science Foundation of ChinaProject(2012DFR60210) supported by the International Cooperation of Ministry of China
文摘Basicity has an important effect on the sinter quality, especially for low-titanium vanadium-titanium sinter. The effect of basieity on sintering behavior of low-titanium vanadium-titanium mixture, and the transference and distribution of element in sintering process were researched by sinter pot test, mineralogical analysis, scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS） analysis. The results show that CaO preferentially reacts with TiO2, generating pervoskite, so that the total liquid phase content of the sinter is low. There is an increase in the perovskite concentration of the sinter with the basicity ranging from 1.9：1 to 2.7：1. With increasing the basicity, the calcium ferrite content increases slightly and then rises rapidly, while the silicate content decreases and the metallurgical property of the sinter is improved. As for the distribution of these elements in the sinter, Ti occurs mainly in perovskite, V occurs mainly in silicate, and Fe occurs mainly in magnetite and hematite. The most abundant occurrence of Ca and Si occurs in silicate and perovskite. With increasing the basicity, the contents of A1 and Mg increase in calcium ferrite, while they decrease in other minerals.
基金the Natural Science Fund of Education Department of Henan Province (200510459077)
文摘The wear resistance of six kinds of the electrolytic low-titanium eutectic AI-Si piston alloys with various Ti content ranging from 0.00wt.% to 0.21wt.% has been studied. A new method of adding Ti is adopted in the electrolytic low-titanium aluminum alloy ingots. The electrolytic low-titanium eutectic AI-Si piston alloys are produced by remelting the electrolytic low-titanium aluminum alloy, crystal silicon, pure magnesium, AI-50%Cu and AI-10%Mn master alloy. The wear experiments are conducted using MM200 wear testing machine under lubricating condition. The results indicate that the better wear resistance and the less weight loss are achieved in the study for the eutectic AI-Si piston alloys with 0.08wt.%-0.12wt.% Ti content. The highest ultimate tensile strength of 135.94 MPa at 300℃ and HV141.70 hardness of the alloys are obtained at 0.12wt.% and 0.08wt.% Ti content, respectively. The wear mechanism of the eutectic AI-Si piston alloys under lubricating condition is abrasive wear.
文摘The effects of superheating temperature on the grain refining efficiency of Ti existing in electrolytic low-titanium aluminum(ELTA)without and with the Al-4B addition and the Al-5Ti-1B master alloy in pure Al were comparatively investigated. The results show that the Ti existing in ELTA without Al-4B addition exhibits a certain grain refining efficiency when the melt superheating temperature is lower,but the efficiency decreases rapidly when the superheating temperature is higher.The grain refining efficiency of the Al-5Ti-1B master alloy is better than that of the Ti existing in ELTA without Al-4B addition at any superheating temperature,but it also decreases obviously with the increase of the superheating temperature.One important reason is that the TiB2 particles coming from the Al-5Ti-1B master alloy can settle down at the bottom of the Al melt easily when the superheating temperature is increased,thus decrease the number of the potent heterogeneous nuclei retained in the Al melt.If the Al-4B master alloy is added to the ELTA melt,the grain refining efficiency of the Ti existing in ELTA can be improved significantly, and does not decrease with the increase of the superheating temperature.This perhaps provides us a possible method to suppress the effect of the superheated melt on the microstructures of aluminum..
文摘The low-cycle fatigue (LCF) behavior of two kinds of A356 alloys produced by different titanium alloying methods was investigated and compared. The effect of titanium content and titanium alloying methods on LCF behavior is analyzed with plastic strain energy density. The results show that all alloys exhibit the cyclic hardening behavior. Raising Ti content can obviously increase the cyclic hardening ability. But the effect of Ti alloying method isn't distinct. Whether for the EA356 alloys or for MA356 alloys, the alloys with low titanium content have longer low-cycle fatigue life than that of the alloys with high titanium content. This is because that the alloys with low titanium content can consume higher cyclic plastic strain energy during cyclic deformation compared with alloys with high titanium content.
